@article{MiyamatoSakakitaWagneretal.2015,
  author    = {Miyamato, Ko-ichiro and Sakakita, Sakura and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Application of chemical imaging sensor to in-situ pH imaging in the vicinity of a corroding metal surface},
  series = {Electrochimica Acta},
  volume    = {183},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2015.07.184},
  pages     = {137 -- 142},
  year      = {2015},
  abstract  = {The chemical imaging sensor was applied to in-situ pH imaging of the solution in the vicinity of a corroding surface of stainless steel under potentiostatic polarization. A test piece of polished stainless steel was placed on the sensing surface leaving a narrow gap filled with artificial seawater and the stainless steel was corroded under polarization. The pH images obtained during polarization showed correspondence between the region of lower pH and the site of corrosion. It was also found that the pH value in the gap became as low as 2 by polarization, which triggered corrosion.},
  language  = {en}
}
@article{HamadBilattoAdlyetal.2016,
  author    = {Hamad, E. M. and Bilatto, S. E. R. and Adly, N. Y. and Correa, D. S. and Wolfrum, B. and Sch{\"o}ning, Michael Josef and Offenh{\"a}usser, A. and Yakushenko, A.},
  title     = {Inkjet printing of UV-curable adhesive and dielectric inks for microfluidic devices},
  series = {Lab on a Chip},
  volume    = {16},
  journal   = {Lab on a Chip},
  number    = {1},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {1473-0189},
  doi       = {10.1039/C5LC01195G},
  pages     = {70 -- 74},
  year      = {2016},
  abstract  = {Bonding of polymer-based microfluidics to polymer substrates still poses a challenge for Lab-On-a-Chip applications. Especially, when sensing elements are incorporated, patterned deposition of adhesives with curing at ambient conditions is required. Here, we demonstrate a fabrication method for fully printed microfluidic systems with sensing elements using inkjet and stereolithographic 3D-printing.},
  language  = {en}
}
@article{HauserKotliarTholenetal.2015,
  author    = {Hauser, C. and Kotliar, Konstantin and Tholen, S. and Hasenau, A. and Suttmann, Y. and Renders, L. and Heemann, U. and Baumann, M. and Schmaderer, C.},
  title     = {Dynamische retinale Gef{\"a}ßreaktion bei H{\"a}modialysepatienten},
  series = {Nieren- und Hochdruckkrankheiten},
  volume    = {44},
  journal   = {Nieren- und Hochdruckkrankheiten},
  number    = {11},
  publisher = {Dustri-Verlag},
  address   = {Oberhaching},
  issn      = {0300-5224},
  doi       = {10.5414/NHX01743a},
  pages     = {480 -- 480},
  year      = {2015},
  language  = {de}
}
@article{Gebhardt2015,
  author    = {Gebhardt, Andreas},
  title     = {3D-Druck ist {\"u}berall. Modische Accessoires, Kleidung, Medikamente, Nahrungsmittel, Autos, H{\"a}user, Waffen, B{\"u}sten, Musikinstrumente - alles geht},
  series = {Kunststoffe},
  volume    = {105},
  journal   = {Kunststoffe},
  number    = {10},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  issn      = {0023-5563},
  pages     = {62 -- 70},
  year      = {2015},
  language  = {de}
}
@article{FischerSelverGezeretal.2015,
  author    = {Fischer, Felix and Selver, M. Alper and Gezer, Sinem and Dicle, Oguz and Hillen, Walter},
  title     = {Systematic Parameterization, Storage, and Representation of Volumetric DICOM Data},
  series = {Journal of Medical and Biological Engineering},
  volume    = {35},
  journal   = {Journal of Medical and Biological Engineering},
  number    = {6},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2199-4757},
  doi       = {10.1007/s40846-015-0097-5},
  pages     = {709 -- 723},
  year      = {2015},
  language  = {en}
}
@article{FredebeulKrein2015,
  author    = {Fredebeul-Krein, Markus},
  title     = {Volkswirtschaftslehre : Die Klausur},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Pr{\"u}fung, Berufseinstieg und Fortbildung},
  volume    = {45},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Pr{\"u}fung, Berufseinstieg und Fortbildung},
  number    = {11},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {1253 -- 1255},
  year      = {2015},
  language  = {de}
}
@article{FredebeulKrein2015,
  author    = {Fredebeul-Krein, Markus},
  title     = {Wettbewerbspolitische Leitbilder},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  volume    = {45},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  number    = {4},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {483 -- 486},
  year      = {2015},
  language  = {de}
}
@article{FredebeulKrein2016,
  author    = {Fredebeul-Krein, Markus},
  title     = {Warum staatliche Kaufpr{\"a}mien f{\"u}r Elektroautos abzulehnen sind},
  series = {Wirtschaftliche Freiheit : das ordnungspolitische Journal},
  volume    = {2016},
  journal   = {Wirtschaftliche Freiheit : das ordnungspolitische Journal},
  number    = {4},
  publisher = {Alexander B. Brunner},
  address   = {W{\"u}rzburg},
  year      = {2016},
  abstract  = {Im Jahr 2015 wurden in Deutschland {\"u}ber drei Millionen Benzinautos und lediglich 12.363 Elektroautos neu zugelassen. Das urspr{\"u}nglich von der Bundesregierung vorgegebene Ziel, dass bis 2020 eine Million E-Autos auf deutschen Straßen fahren (und bis 2030 sechs Millionen), r{\"u}ckt damit in immer weitere Ferne. Um das Ziel dennoch zu erreichen, plant die Bundesregierung nun eine staatli­che Pr{\"a}mie f{\"u}r den Kauf von Elektroautos: Umwelt-, Verkehrs- und Wirtschaftsministerium haben gemeinsam ein Konzept entworfen, dem zufolge private K{\"a}ufer zuk{\"u}nftig einen Zuschuss von 5.000 Euro beim Erwerb eines Elektroautos bekommen sollen. 40 Prozent dieses Zuschusses soll von den Autoherstellern getragen werden. Das Programm, das weitere ausgabenwirksame {\"o}ffentli­che Maßnahmen vorsieht, w{\"u}rde Kosten in Milliarden­h{\"o}he verursachen. Die beabsichtigte Subventionierung wirft die Frage auf, ob diese wirtschaftlich sinnvoll sind.},
  language  = {de}
}
@article{BayonValeroGarciaBartualetal.2016,
  author    = {Bayon, Arnau and Valero, Daniel and Garcia-Bartual, Rafael and Vall{\´e}s-Mor{\´a}n, Francisco Jos{\´e} and L{\´o}pez-Jim{\´e}nez, P. Amparo},
  title     = {Performance assessment of OpenFOAM and FLOW-3D in the numerical modeling of a low Reynolds number hydraulic jump},
  series = {Environmental Modelling \& Software},
  volume    = {80},
  journal   = {Environmental Modelling \& Software},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {1364-8152},
  doi       = {10.1016/j.envsoft.2016.02.018},
  pages     = {322 -- 335},
  year      = {2016},
  abstract  = {A comparative performance analysis of the CFD platforms OpenFOAM and FLOW-3D is presented, focusing on a 3D swirling turbulent flow: a steady hydraulic jump at low Reynolds number. Turbulence is treated using RANS approach RNG k-ε. A Volume Of Fluid (VOF) method is used to track the air-water interface, consequently aeration is modeled using an Eulerian-Eulerian approach. Structured meshes of cubic elements are used to discretize the channel geometry. The numerical model accuracy is assessed comparing representative hydraulic jump variables (sequent depth ratio, roller length, mean velocity profiles, velocity decay or free surface profile) to experimental data. The model results are also compared to previous studies to broaden the result validation. Both codes reproduced the phenomenon under study concurring with experimental data, although special care must be taken when swirling flows occur. Both models can be used to reproduce the hydraulic performance of energy dissipation structures at low Reynolds numbers.},
  language  = {en}
}
@article{MiyamotoYuIsodaetal.2016,
  author    = {Miyamoto, Ko-ichiro and Yu, Bing and Isoda, Hiroko and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Visualization of the recovery process of defects in a cultured cell layer by chemical imaging sensor},
  series = {Sensors and Actuators B: Chemical},
  volume    = {236},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2016.04.018},
  pages     = {965 -- 969},
  year      = {2016},
  abstract  = {The chemical imaging sensor is a field-effect sensor which is able to visualize both the distribution of ions (in LAPS mode) and the distribution of impedance (in SPIM mode) in the sample. In this study, a novel cell assay is proposed, in which the chemical imaging sensor operated in SPIM mode is applied to monitor the recovery of defects in a cell layer brought into proximity of the sensing surface. A reduced impedance at a defect formed artificially in a cell layer was successfully visualized in a photocurrent image. The cell layer was cultured over two weeks, during which the temporal change of the photocurrent distribution corresponding to the recovery of the defect was observed.},
  language  = {de}
}