@inproceedings{Butenweg2021,
  author    = {Butenweg, Christoph},
  title     = {Integrated approach for monitoring and management of buildings with digital building models and modern sensor technologies},
  series = {Proceedings of the International Conference Civil Engineering 2021 - Achievements and Visions},
  booktitle = {Proceedings of the International Conference Civil Engineering 2021 - Achievements and Visions},
  editor    = {Kuzmanović, Vladan and Ignjatović, Ivan},
  publisher = {University of Belgrade},
  address   = {Belgrade},
  pages     = {67 -- 75},
  year      = {2021},
  abstract  = {Nowadays modern high-performance buildings and facilities are equipped with monitoring systems and sensors to control building characteristics like energy consumption, temperature pattern and structural safety. The visualization and interpretation of sensor data is typically based on simple spreadsheets and non-standardized user-oriented solutions, which makes it difficult for building owners, facility managers and decision-makers to evaluate and understand the data. The solution of this problem in the future are integrated BIM-Sensor approaches which allow the generation of BIM models incorporating all relevant information of monitoring systems. These approaches support both the dynamic visualization of key structural performance parameters, the effective long-term management of sensor data based on BIM and provide a user-friendly interface to communicate with various stakeholders. A major benefit for the end user is the use of the BIM software architecture, which is the future standard anyway. In the following, the application of the integrated BIM-Sensor approach is illustrated for a typical industrial facility as a part of an early warning and rapid response system for earthquake events currently developed in the research project "ROBUST" with financial support by the German Federal Ministry for Economic Affairs and Energy (BMWI).},
  language  = {en}
}
@article{Dachwald2003,
  author    = {Dachwald, Bernd},
  title     = {Verwendung eines neuronalen Reglers und evolution{\"a}rer Algorithmen zur Berechnung optimaler interplanetarer Sonnenseglerbahnen},
  series = {Deutscher Luft- und Raumfahrtkongress 2003 : M{\"u}nchen, 17. bis 20. November 2003, Motto: 100 Jahre Motorflug - 112 Jahre Menschenflug: Visionen gestalten Zukunft / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V. (DGLR). [Red.: Peter Brandt (verantwortlich)]. - Bd. 1. - (Jahrbuch ... der Deutschen Gesellschaft f{\"u}r Luft- und Raumfahrt)},
  journal   = {Deutscher Luft- und Raumfahrtkongress 2003 : M{\"u}nchen, 17. bis 20. November 2003, Motto: 100 Jahre Motorflug - 112 Jahre Menschenflug: Visionen gestalten Zukunft / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V. (DGLR). [Red.: Peter Brandt (verantwortlich)]. - Bd. 1. - (Jahrbuch ... der Deutschen Gesellschaft f{\"u}r Luft- und Raumfahrt)},
  address   = {Bonn},
  pages     = {211 -- 218},
  year      = {2003},
  language  = {de}
}
@article{EggertKnackstedtFleischeretal.2013,
  author    = {Eggert, Mathias and Knackstedt, Ralf and Fleischer, Stefan and Becker, J{\"o}rg},
  title     = {The Potential of Configurative Reference Modeling for Business to Government Reporting - A Modeling Technique and its Evaluation},
  series = {e-Service Journal},
  volume    = {9},
  journal   = {e-Service Journal},
  number    = {1},
  publisher = {Indiana University Press},
  address   = {Bloomington},
  issn      = {1528-8234},
  pages     = {28 -- 59},
  year      = {2013},
  language  = {en}
}
@incollection{WolfFoltzLuczak2003,
  author    = {Wolf, Martin R. and Foltz, Christian and Luczak, Holger},
  title     = {Gestaltung und Evaluation eines Groupware-Konzepts},
  series = {Modelle, Werkzeuge und Infrastrukturen zur Unterst{\"u}tzung von Entwicklungsprozessen},
  booktitle = {Modelle, Werkzeuge und Infrastrukturen zur Unterst{\"u}tzung von Entwicklungsprozessen},
  editor    = {Nagl, Manfred},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  isbn      = {3-527-27769-2},
  pages     = {359 -- 360},
  year      = {2003},
  language  = {de}
}
@book{EngelnMuellgesUhlig1996,
  author    = {Engeln-M{\"u}llges, Gisela and Uhlig, Frank},
  title     = {Numeric Algorithms with Fortran},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {3-540-60529-0},
  pages     = {XXII, 602 S. : Ill., graph. Darst. + 1 CD-ROM},
  year      = {1996},
  language  = {en}
}
@article{MarinkovićFloresCalvinistiButenweg2020,
  author    = {Marinković, Marko and Flores Calvinisti, Santiago and Butenweg, Christoph},
  title     = {Numerical analysis of reinforced concrete frame buildings with decoupled infill walls},
  series = {Building Materials and Structures},
  volume    = {63},
  journal   = {Building Materials and Structures},
  number    = {4},
  publisher = {Society for Materials and Structures Testing of Serbia},
  address   = {Belgrad},
  issn      = {2217-8139},
  doi       = {10.5937/GRMK2004013M},
  pages     = {13 -- 48},
  year      = {2020},
  abstract  = {Reinforced concrete (RC) buildings with masonry infill walls are widely used in many countries all over the world. Although infills are considered as non-structural elements, they significantly change dynamic characteristics of RC frame structures during earthquake excitation. Recently, significant effort was spent on studying decoupled infills, which are isolated from the surrounding frame usually by adding a gap between frame and infill. In this case, the frame deformation does not activate infill wall, thus infills are not influencing the behaviour of the frame. This paper presents the results of the investigation of the behaviour of RC frame buildings with the INODIS system that decouples masonry infills from the surrounding frame. Effect of masonry infill decoupling was investigated first on the one-bay onestorey frame. This was used as a base for parametric study on the frames with more bays and storeys, as well as on the building level. Change of stiffness and dynamic characteristics was analysed as well as response under earthquake loading. Comparison with the bare frame and traditionally infilled frame was performed. The results show that behaviour of the decoupled infilled frames is similar to the bare frame, whereas behaviour of frames with traditional infills is significantly different and demands complex numerical models. This means that if adequate decoupling is applied, design of},
  language  = {mul}
}
@inproceedings{LuBeyerBosiljkovetal.2016,
  author    = {Lu, S. and Beyer, K. and Bosiljkov, V. and Butenweg, Christoph and D'Ayala, D. and Degee, H. and Gams, M. and Klouda, J. and Lagomarsino, S. and Penna, A. and Mojsilovic, N. and da Porto, F. and Sorrentino, L. and Vintzileou, E.},
  title     = {Next generation of Eurocode 8, masonry chapter},
  series = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  booktitle = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  editor    = {Modena, Claudio and da Porto, F. and Valluzzi, M.R.},
  publisher = {Taylor \& Francis},
  address   = {London},
  isbn      = {978-1-138-02999-6 (Print)},
  pages     = {695 -- 700},
  year      = {2016},
  abstract  = {This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date.},
  language  = {en}
}
@inproceedings{PirovanoSeefeldtDachwaldetal.2015,
  author    = {Pirovano, Laura and Seefeldt, Patric and Dachwald, Bernd and Noomen, Ron},
  title     = {Attitude and orbital modeling of an uncontrolled solar-sail experiment in low-Earth orbit},
  series = {25th International Symposium on Space Flight Dynamics ISSFD},
  booktitle = {25th International Symposium on Space Flight Dynamics ISSFD},
  pages     = {1 -- 15},
  year      = {2015},
  abstract  = {Gossamer-1 is the first project of the three-step Gossamer roadmap, the purpose of which is to develop, prove and demonstrate that solar-sail technology is a safe and reliable propulsion technique for long-lasting and high-energy missions. This paper firstly presents the structural analysis performed on the sail to understand its elastic behavior. The results are then used in attitude and orbital simulations. The model considers the main forces and torques that a satellite experiences in low-Earth orbit coupled with the sail deformation. Doing the simulations for varying initial conditions in attitude and rotation rate, the results show initial states to avoid and maximum rotation rates reached for correct and faulty deployment of the sail. Lastly comparisons with the classic flat sail model are carried out to test the hypothesis that the elastic behavior does play a role in the attitude and orbital behavior of the sail},
  language  = {en}
}
@inproceedings{MaikeLenzWolf2014,
  author    = {Maike, M{\"u}ller and Lenz, Laura and Wolf, Martin R.},
  title     = {Steigerung der Effektivit{\"a}t durch Prozessmodellierungs-Tools - {\"A}nderbarkeit und Transparenz von Prozessen am Beispiel der Business Simulation Apollo 13},
  series = {Informatik 2014},
  booktitle = {Informatik 2014},
  publisher = {Gesellschaft f{\"u}r Informatik e.V.},
  address   = {Bonn},
  isbn      = {978-3-88579-626-8},
  issn      = {1617-5468},
  pages     = {357 -- 369},
  year      = {2014},
  abstract  = {Die Nutzung von Prozessmodellierungsmethoden oder - werkzeugen kann erheblichen Einfluss auf die Effektivit{\"a}t von Prozessen haben. Das gilt insbesondere f{\"u}r Situationen, in denen Personen unter Stress stehen oder unge{\"u}bt sind. In diesen F{\"a}llen geben Prozessmodelle konkrete Empfehlungen, nach denen sich die handelnden Personen richten k{\"o}nnten. In Experimenten mit der Business-Simulation Apollo 13 haben wir den Effekt eines Einsatzes von Prozessmodellierungsmethoden und -werkzeugen untersucht. Bereits bekannte Theorien (z.B. {\"u}ber geeignete Verh{\"a}ltnisse von Kommunikationsinhalten) konnten best{\"a}tigt werden. Dar{\"u}ber hinaus haben wir eine besondere Bedeutung der {\"U}bertragbarkeit von Prozessmodellen in konkrete Handlungen identifiziert.},
  language  = {de}
}
@incollection{LuczakWolfMuehlfelder2001,
  author    = {Luczak, Holger and Wolf, Martin R. and M{\"u}hlfelder, M.},
  title     = {Arbeitswissenschaft},
  series = {CSCW-Kompendium : Lehr- und Handbuch zum computerunterst{\"u}tzten kooperativen Arbeiten ; mit 9 Tabellen},
  booktitle = {CSCW-Kompendium : Lehr- und Handbuch zum computerunterst{\"u}tzten kooperativen Arbeiten ; mit 9 Tabellen},
  editor    = {Schwabe, Gerhard},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-67552-5},
  doi       = {10.1007/978-3-642-56848-0_2},
  pages     = {7 -- 14},
  year      = {2001},
  abstract  = {Unter Arbeit wird das T{\"a}tigsein des Menschen verstanden, bei dem dieser mit anderen Menschen und (technischen) Hilfsmitteln in Interaktion tritt, um unter wirtschaftlichen Zielsetzungen G{\"u}ter und Dienstleistungen zu erstellen (Luczak, 1998a). Arbeit dient direkt oder indirekt der Erhaltung der eigenen Existenz und der Existenz der Gesellschaft. Arbeit ist deshalb eine besondere Form des T{\"a}tigseins neben anderen wie Spiel, Sport, Lemen usw.},
  language  = {de}
}