@article{SchopenNarayanBeckmannetal.2024,
  author    = {Schopen, Oliver and Narayan, Sriram and Beckmann, Marvin and Najmi, Aezid-Ul-Hassan and Esch, Thomas and Shabani, Bahman},
  title     = {An EIS approach to quantify the effects of inlet air relative humidity on the performance of proton exchange membrane fuel cells: a pathway to developing a novel fault diagnostic method},
  series = {International Journal of Hydrogen Energy},
  volume    = {58},
  journal   = {International Journal of Hydrogen Energy},
  number    = {8},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0360-3199 (print)},
  issn      = {1879-3487 (online)},
  doi       = {10.1016/j.ijhydene.2024.01.218},
  pages     = {1302 -- 1315},
  year      = {2024},
  abstract  = {In this work, the effect of low air relative humidity on the operation of a polymer electrolyte membrane fuel cell is investigated. An innovative method through performing in situ electrochemical impedance spectroscopy is utilised to quantify the effect of inlet air relative humidity at the cathode side on internal ionic resistances and output voltage of the fuel cell. In addition, algorithms are developed to analyse the electrochemical characteristics of the fuel cell. For the specific fuel cell stack used in this study, the membrane resistance drops by over 39 \% and the cathode side charge transfer resistance decreases by 23 \% after increasing the humidity from 30 \% to 85 \%, while the results of static operation also show an increase of ∼2.2 \% in the voltage output after increasing the relative humidity from 30 \% to 85 \%. In dynamic operation, visible drying effects occur at < 50 \% relative humidity, whereby the increase of the air side stoichiometry increases the drying effects. Furthermore, other parameters, such as hydrogen humidification, internal stack structure, and operating parameters like stoichiometry, pressure, and temperature affect the overall water balance. Therefore, the optimal humidification range must be determined by considering all these parameters to maximise the fuel cell performance and durability. The results of this study are used to develop a health management system to ensure sufficient humidification by continuously monitoring the fuel cell polarisation data and electrochemical impedance spectroscopy indicators.},
  language  = {en}
}
@inproceedings{StarkRiepingEsch2023,
  author    = {Stark, Ralf and Rieping, Carla and Esch, Thomas},
  title     = {The impact of guide tubes on flow separation in rocket nozzles},
  series = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  booktitle = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  pages     = {8 Seiten},
  year      = {2023},
  abstract  = {Rocket engine test facilities and launch pads are typically equipped with a guide tube. Its purpose is to ensure the controlled and safe routing of the hot exhaust gases. In addition, the guide tube induces a suction that effects the nozzle flow, namely the flow separation during transient start-up and shut-down of the engine. A cold flow subscale nozzle in combination with a set of guide tubes was studied experimentally to determine the main influencing parameters.},
  language  = {en}
}
@inproceedings{StarkBartelDitscheetal.2023,
  author    = {Stark, Ralf and Bartel, Sebastian and Ditsche, Florian and Esch, Thomas},
  title     = {Design study of a 30kN LOX/LCH4 aerospike rocket engine for lunar lander application},
  series = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  booktitle = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  pages     = {9 Seiten},
  year      = {2023},
  abstract  = {Based on lunar lander concept EL3, various LOX/CH4 aerospike engines were studied. A distinction was made between single and cluster configurations as well as ideal and non-ideal contour concepts. It could be shown that non-ideal aerospike engines promise a significant payload gain.},
  language  = {en}
}
@article{StiemerThomaBraun2023,
  author    = {Stiemer, Luc Nicolas and Thoma, Andreas and Braun, Carsten},
  title     = {MBT3D: Deep learning based multi-object tracker for bumblebee 3D flight path estimation},
  series = {PLoS ONE},
  volume    = {18},
  journal   = {PLoS ONE},
  number    = {9},
  publisher = {PLOS},
  address   = {San Fancisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0291415},
  pages     = {e0291415},
  year      = {2023},
  abstract  = {This work presents the Multi-Bees-Tracker (MBT3D) algorithm, a Python framework implementing a deep association tracker for Tracking-By-Detection, to address the challenging task of tracking flight paths of bumblebees in a social group. While tracking algorithms for bumblebees exist, they often come with intensive restrictions, such as the need for sufficient lighting, high contrast between the animal and background, absence of occlusion, significant user input, etc. Tracking flight paths of bumblebees in a social group is challenging. They suddenly adjust movements and change their appearance during different wing beat states while exhibiting significant similarities in their individual appearance. The MBT3D tracker, developed in this research, is an adaptation of an existing ant tracking algorithm for bumblebee tracking. It incorporates an offline trained appearance descriptor along with a Kalman Filter for appearance and motion matching. Different detector architectures for upstream detections (You Only Look Once (YOLOv5), Faster Region Proposal Convolutional Neural Network (Faster R-CNN), and RetinaNet) are investigated in a comparative study to optimize performance. The detection models were trained on a dataset containing 11359 labeled bumblebee images. YOLOv5 reaches an Average Precision of AP = 53, 8\%, Faster R-CNN achieves AP = 45, 3\% and RetinaNet AP = 38, 4\% on the bumblebee validation dataset, which consists of 1323 labeled bumblebee images. The tracker's appearance model is trained on 144 samples. The tracker (with Faster R-CNN detections) reaches a Multiple Object Tracking Accuracy MOTA = 93, 5\% and a Multiple Object Tracking Precision MOTP = 75, 6\% on a validation dataset containing 2000 images, competing with state-of-the-art computer vision methods. The framework allows reliable tracking of different bumblebees in the same video stream with rarely occurring identity switches (IDS). MBT3D has much lower IDS than other commonly used algorithms, with one of the lowest false positive rates, competing with state-of-the-art animal tracking algorithms. The developed framework reconstructs the 3-dimensional (3D) flight paths of the bumblebees by triangulation. It also handles and compares two alternative stereo camera pairs if desired.},
  language  = {en}
}
@inproceedings{GrundAltherr2023,
  author    = {Grund, Raphael M. and Altherr, Lena},
  title     = {Development of an open source energy disaggregation tool for the home automation platform Home Assistant},
  series = {Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel},
  booktitle = {Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel},
  editor    = {Reiff-Stephan, J{\"o}rg and J{\"a}kel, Jens and Schwarz, Andr{\´e}},
  publisher = {le-tex publishing services GmbH},
  address   = {Leipzig},
  isbn      = {978-3-910103-01-6},
  doi       = {10.33968/2023.02},
  pages     = {11 -- 20},
  year      = {2023},
  abstract  = {In order to reduce energy consumption of homes, it is important to make transparent which devices consume how much energy. However, power consumption is often only monitored aggregated at the house energy meter. Disaggregating this power consumption into the contributions of individual devices can be achieved using Machine Learning. Our work aims at making state of the art disaggregation algorithms accessibe for users of the open source home automation platform Home Assistant.},
  language  = {en}
}
@inproceedings{NiederwestbergSchneiderTeixeiraBouraetal.2022,
  author    = {Niederwestberg, Stefan and Schneider, Falko and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Introduction to a direct irradiated transparent tube particle receiver},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086735},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {New materials often lead to innovations and advantages in technical applications. This also applies to the particle receiver proposed in this work that deploys high-temperature and scratch resistant transparent ceramics. With this receiver design, particles are heated through direct-contact concentrated solar irradiance while flowing downwards through tubular transparent ceramics from top to bottom. In this paper, the developed particle receiver as well as advantages and disadvantages are described. Investigations on the particle heat-up characteristics from solar irradiance were carried out with DEM simulations which indicate that particle temperatures can reach up to 1200 K. Additionally, a simulation model was set up for investigating the dynamic behavior. A test receiver at laboratory scale has been designed and is currently being built. In upcoming tests, the receiver test rig will be used to validate the simulation results. The design and the measurement equipment is described in this work.},
  language  = {en}
}
@inproceedings{NeumannAdamBackesetal.2021,
  author    = {Neumann, Hannah and Adam, Mario and Backes, Klaus and B{\"o}rner, Martin and Clees, Tanja and Doetsch, Christian and Glaeser, Susanne and Herrmann, Ulf and May, Johanna and Rosenthal, Florian and Sauer, Dirk Uwe and Stadler, Ingo},
  title     = {Development of open educational resources for renewable energy and the energy transition process},
  series = {ISES SWC 2021},
  booktitle = {ISES SWC 2021},
  publisher = {International Solar Energy Society},
  address   = {Freiburg},
  doi       = {10.18086/swc.2021.47.03},
  pages     = {6 Seiten},
  year      = {2021},
  abstract  = {The dissemination of knowledge about renewable energies is understood as a social task with the highest topicality. The transfer of teaching content on renewable energies into digital open educational resources offers the opportunity to significantly accelerate the implementation of the energy transition. Thus, in the here presented project six German universities create open educational resources for the energy transition. These materials are available to the public on the internet under a free license. So far there has been no publicly accessible, editable media that cover entire learning units about renewable energies extensively and in high technical quality. Thus, in this project, the content that remains up-to-date for a longer period is appropriately prepared in terms of media didactics. The materials enable lecturers to provide students with in-depth training about technologies for the energy transition. In a particular way, the created material is also suitable for making the general public knowledgeable about the energy transition with scientifically based material.},
  language  = {en}
}
@inproceedings{SattlerSchneiderAngeleetal.2022,
  author    = {Sattler, Johannes Christoph and Schneider, Iesse Peer and Angele, Florian and Atti, Vikrama and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Development of heliostat field calibration methods: Theory and experimental test results},
  series = {SolarPACES 2022 conference proceedings},
  booktitle = {SolarPACES 2022 conference proceedings},
  number    = {1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.678},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {In this work, three patent pending calibration methods for heliostat fields of central receiver systems (CRS) developed by the Solar-Institut J{\"u}lich (SIJ) of the FH Aachen University of Applied Sciences are presented. The calibration methods can either operate in a combined mode or in stand-alone mode. The first calibration method, method A, foresees that a camera matrix is placed into the receiver plane where it is subjected to concentrated solar irradiance during a measurement process. The second calibration method, method B, uses an unmanned aerial vehicle (UAV) such as a quadrocopter to automatically fly into the reflected solar irradiance cross-section of one or more heliostats (two variants of method B were tested). The third calibration method, method C, foresees a stereo central camera or multiple stereo cameras installed e.g. on the solar tower whereby the orientations of the heliostats are calculated from the location detection of spherical red markers attached to the heliostats. The most accurate method is method A which has a mean accuracy of 0.17 mrad. The mean accuracy of method B variant 1 is 1.36 mrad and of variant 2 is 1.73 mrad. Method C has a mean accuracy of 15.07 mrad. For method B there is great potential regarding improving the measurement accuracy. For method C the collected data was not sufficient for determining whether or not there is potential for improving the accuracy.},
  language  = {en}
}
@inproceedings{SchwagerAngeleNourietal.2022,
  author    = {Schwager, Christian and Angele, Florian and Nouri, Bijan and Schwarzb{\"o}zl, Peter and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Impact of DNI forecast quality on performance prediction for a commercial scale solar tower: Application of nowcasting DNI maps to dynamic solar tower simulation},
  series = {SolarPACES 2022 conference proceedings},
  booktitle = {SolarPACES 2022 conference proceedings},
  number    = {1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.675},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concerning current efforts to improve operational efficiency and to lower overall costs of concentrating solar power (CSP) plants with prediction-based algorithms, this study investigates the quality and uncertainty of nowcasting data regarding the implications for process predictions. DNI (direct normal irradiation) maps from an all-sky imager-based nowcasting system are applied to a dynamic prediction model coupled with ray tracing. The results underline the need for high-resolution DNI maps in order to predict net yield and receiver outlet temperature realistically. Furthermore, based on a statistical uncertainty analysis, a correlation is developed, which allows for predicting the uncertainty of the net power prediction based on the corresponding DNI forecast uncertainty. However, the study reveals significant prediction errors and the demand for further improvement in the accuracy at which local shadings are forecasted.},
  language  = {en}
}
@inproceedings{SchulteSchwagerFrantzetal.2022,
  author    = {Schulte, Jonas and Schwager, Christian and Frantz, Cathy and Schloms, Felix and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Control concept for a molten salt receiver in star design: Development, optimization and testing with cloud passage scenarios},
  series = {SolarPACES 2022 conference proceedings},
  booktitle = {SolarPACES 2022 conference proceedings},
  number    = {1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.693},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {A promising approach to reduce the system costs of molten salt solar receivers is to enable the irradiation of the absorber tubes on both sides. The star design is an innovative receiver design, pursuing this approach. The unconventional design leads to new challenges in controlling the system. This paper presents a control concept for a molten salt receiver system in star design. The control parameters are optimized in a defined test cycle by minimizing a cost function. The control concept is tested in realistic cloud passage scenarios based on real weather data. During these tests, the control system showed no sign of unstable behavior, but to perform sufficiently in every scenario further research and development like integrating Model Predictive Controls (MPCs) need to be done. The presented concept is a starting point to do so.},
  language  = {en}
}