@article{HeinkeKnickerAlbracht2020,
  author    = {Heinke, Lars N. and Knicker, Axel J. and Albracht, Kirsten},
  title     = {Increased shoulder muscle stretch reflex elicitability in supine subject posture},
  series = {Isokinetics and Exercise Science},
  volume    = {28},
  journal   = {Isokinetics and Exercise Science},
  number    = {2},
  publisher = {IOS Press},
  address   = {Amsterdam},
  issn      = {1878-5913},
  doi       = {10.3233/IES-192219},
  pages     = {139 -- 146},
  year      = {2020},
  abstract  = {BACKGROUND: Muscle stretch reflexes are widely used to examine neural muscle function. The knowledge of reflex response in muscles crossing the shoulder is limited. OBJECTIVE: To quantify reflex modulation according to various subject postures and different procedures of muscle pre-activation steering. METHODS: Thirteen healthy male participants performed two sets of external shoulder rotation stretches in various positions and with different procedures of muscle pre-activation steering on an isokinetic dynamometer over a range of two different pre-activation levels. All stretches were applied with a dynamometer acceleration of 104∘/s2 and a velocity of 150∘/s. Electromyographical response was measured via sEMG. RESULTS: Consistent reflexive response was observed in all tested muscles in all experimental conditions. The reflex elicitation rate revealed a significant muscle main effect (F (5,288) = 2.358, ρ= 0.040; η2= 0.039; f= 0.637) and a significant test condition main effect (F (1,288) = 5.884, ρ= 0.016; η2= 0.020; f= 0.143). Reflex latency revealed a significant muscle pre-activation level main effect (F (1,274) = 5.008, ρ= 0.026; η2= 0.018; f= 0.469). CONCLUSION: Muscular reflexive response was more consistent in the primary internal rotators of the shoulder. Supine posture in combination with visual feedback of muscle pre-activation level enhanced the reflex elicitation rate.},
  language  = {en}
}
@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}
@article{ChoiFelderFelderetal.2020,
  author    = {Choi, Chang-Hoon and Felder, Tim and Felder, J{\"o}rg and Tellmann, Lutz and Hong, Suk-Min and Wegener, Hans-Peter and Shah, N Jon and Ziemons, Karl},
  title     = {Design, evaluation and comparison of endorectal coils for hybrid MR-PET imaging of the prostate},
  series = {Physics in Medicine \& Biology},
  volume    = {65},
  journal   = {Physics in Medicine \& Biology},
  number    = {11},
  publisher = {IOP},
  address   = {Bristol},
  issn      = {0031-9155},
  doi       = {10.1088/1361-6560/ab87f8},
  year      = {2020},
  abstract  = {Prostate cancer is one of the most common cancers among men and its early detection is critical for its successful treatment. The use of multimodal imaging, such as MR-PET, is most advantageous as it is able to provide detailed information about the prostate. However, as the human prostate is flexible and can move into different positions under external conditions, it is important to localise the focused region-of-interest using both MRI and PET under identical circumstances. In this work, we designed five commonly used linear and quadrature radiofrequency surface coils suitable for hybrid MR-PET use in endorectal applications. Due to the endorectal design and the shielded PET insert, the outer face of the coils investigated was curved and the region to be imaged was outside the volume of the coil. The tilting angles of the coils were varied with respect to the main magnetic field direction. This was done to approximate the various positions from which the prostate could be imaged. The transmit efficiencies and safety excitation efficiencies from simulations, together with the signal-to-noise ratios from the MR images were calculated and analysed. Overall, it was found that the overlapped loops driven in quadrature were superior to the other types of coils we tested. In order to determine the effect of the different coil designs on PET, transmission scans were carried out, and it was observed that the differences between attenuation maps with and without the coils were negligible. The findings of this work can provide useful guidance for the integration of such coil designs into MR-PET hybrid systems in the future.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalili, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modeling with Application in Industry 4.0},
  series = {IEEE Access},
  volume    = {8},
  journal   = {IEEE Access},
  number    = {Art. 9108222},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {111381 -- 111393},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@inproceedings{BraunChengDoweyetal.2020,
  author    = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Survey on Security Concepts to Adapt Flexible Manufacturing and Operations Management based upon Multi-Agent Systems},
  series = {2020 IEEE 29th International Symposium on Industrial Electronics (ISIE), Proceedings},
  booktitle = {2020 IEEE 29th International Symposium on Industrial Electronics (ISIE), Proceedings},
  publisher = {IEEE},
  address   = {New York, NY},
  doi       = {10.1109/ISIE45063.2020.9152210},
  pages     = {5 Seiten},
  year      = {2020},
  abstract  = {The increasing digitalization brings new opportunities but also puts new challenges to modern industrial systems. Software agents are one of the key technologies towards self-optimizing factories and are currently used to address the needs of cyber-physical production systems (CPPS). However their interplay in industrial settings needs to be understood better.This paper focusses on securing a cloud infrastructure for multi-agent systems for industrial sites. An industrial site contains multiple production processes that need to communicate with each other and each physical resource is abstracted with a software agent. This volatile architecture needs to be managed and protected from manipulation. The proposed infrastructure presents a security concept for TCP/IP communication between agents, machines, and external networks. It is based on open-source software and tested on a three-node edge cloud controlling a model-plant.},
  language  = {en}
}
@article{KuhnhenneRegerPyschnyetal.2020,
  author    = {Kuhnhenne, Markus and Reger, Vitali and Pyschny, Dominik and D{\"o}ring, Bernd},
  title     = {Influence of airtightness of steel sandwich panel joints on heat losses},
  series = {E3S Web of Conferences 12th Nordic Symposium on Building Physics (NSB 2020)},
  volume    = {172},
  journal   = {E3S Web of Conferences 12th Nordic Symposium on Building Physics (NSB 2020)},
  number    = {Art. 05008},
  publisher = {EDP Sciences},
  address   = {Les Ulis},
  doi       = {10.1051/e3sconf/202017205008},
  pages     = {6},
  year      = {2020},
  abstract  = {Energy saving ordinances requires that buildings must be designed in such a way that the heat transfer surface including the joints is permanently air impermeable. The prefabricated roof and wall panels in lightweight steel constructions are airtight in the area of the steel covering layers. The sealing of the panel joints contributes to fulfil the comprehensive requirements for an airtight building envelope. To improve the airtightness of steel sandwich panels, additional sealing tapes can be installed in the panel joint. The influence of these sealing tapes was evaluated by measurements carried out by the RWTH Aachen University - Sustainable Metal Building Envelopes. Different installation situations were evaluated by carrying out airtightness tests for different joint distances. In addition, the influence on the heat transfer coefficient was also evaluated using the Finite Element Method (FEM). The combination of obtained air volume flow and transmission losses enables to create an "effective heat transfer coefficient" due to transmission and infiltration. This summarizes both effects in one value and is particularly helpful for approximate calculations on energy efficiency.},
  language  = {en}
}
@article{MaurischatPerkins2020,
  author    = {Maurischat, Andreas and Perkins, Rudolph},
  title     = {Taylor coefficients of Anderson generating functions and Drinfeld torsion extensions},
  number    = {Vol. 18, No. 01},
  publisher = {World Scientific},
  address   = {Singapur},
  doi       = {10.1142/S1793042122500099},
  pages     = {113 -- 130},
  year      = {2020},
  abstract  = {We generalize our work on Carlitz prime power torsion extension to torsion extensions of Drinfeld modules of arbitrary rank. As in the Carlitz case, we give a description of these extensions in terms of evaluations of Anderson generating functions and their hyperderivatives at roots of unity. We also give a direct proof that the image of the Galois representation attached to the p-adic Tate module lies in the p-adic points of the motivic Galois group. This is a generalization of the corresponding result of Chang and Papanikolas for the t-adic case.},
  language  = {en}
}
@article{ElMoussaouiTalbiAtmaneetal.2020,
  author    = {El Moussaoui, Noureddine and Talbi, Sofian and Atmane, Ilyas and Kassmi, Khalil and Schwarzer, Klemens and Chayeb, Hamid and Bachiri, Najib},
  title     = {Feasibility of a new design of a Parabolic Trough Solar Thermal Cooker (PSTC)},
  series = {Solar Energy},
  volume    = {201},
  journal   = {Solar Energy},
  number    = {Vol. 201 (May 2020)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0038-092X},
  doi       = {10.1016/j.solener.2020.03.079},
  pages     = {866 -- 871},
  year      = {2020},
  abstract  = {In this article, we describe the structure, the functioning, and the tests of parabolic trough solar thermal cooker (PSTC). This oven is designed to meet the needs of rural residents, including Urban, which requires stable cooking temperatures above 200 °C. The cooking by this cooker is based on the concentration of the sun's rays on a glass vacuum tube and heating of the oil circulate in a big tube, located inside the glass tube. Through two small tubes, associated with large tube, the heated oil, rise and heats the pot of cooking pot containing the food to be cooked (capacity of 5 kg). This cooker is designed in Germany and extensively tested in Morocco for use by the inhabitants who use wood from forests. During a sunny day, having a maximum solar radiation around 720 W/m2 and temperature ambient around 26 °C, maximum temperatures recorded of the small tube, the large tube and the center of the pot are respectively: 370 °C, 270 °C and 260 °C. The cooking process with food at high (fries, ..), we show that the cooking oil temperature rises to 200 °C, after 1 h of heating, the cooking is done at a temperature of 120 °C for 20 min. These temperatures are practically stable following variations and decreases in the intensity of irradiance during the day. The comparison of these results with those of the literature shows an improvement of 30-50 \% on the maximum value of the temperature with a heat storage that could reach 60 min of autonomy. All the results obtained show the good functioning of the PSTC and the feasibility of cooking food at high temperature (>200 °C).},
  language  = {en}
}
@article{OrzadaFiedlerBitzetal.2020,
  author    = {Orzada, Stephan and Fiedler, Thomas M. and Bitz, Andreas and Ladd, Mark E. and Quick, Harald H.},
  title     = {Local SAR compression with overestimation control to reduce maximum relative SAR overestimation and improve multi-channel RF array performance},
  series = {Magnetic Resonance Materials in Physics, Biology and Medicine},
  journal   = {Magnetic Resonance Materials in Physics, Biology and Medicine},
  number    = {34 (2021)},
  publisher = {Springer},
  address   = {Heidelberg},
  isbn      = {1352-8661},
  doi       = {10.1007/s10334-020-00890-0},
  pages     = {153 -- 164},
  year      = {2020},
  abstract  = {Objective In local SAR compression algorithms, the overestimation is generally not linearly dependent on actual local SAR. This can lead to large relative overestimation at low actual SAR values, unnecessarily constraining transmit array performance. Method Two strategies are proposed to reduce maximum relative overestimation for a given number of VOPs. The first strategy uses an overestimation matrix that roughly approximates actual local SAR; the second strategy uses a small set of pre-calculated VOPs as the overestimation term for the compression. Result Comparison with a previous method shows that for a given maximum relative overestimation the number of VOPs can be reduced by around 20\% at the cost of a higher absolute overestimation at high actual local SAR values. Conclusion The proposed strategies outperform a previously published strategy and can improve the SAR compression where maximum relative overestimation constrains the performance of parallel transmission.},
  language  = {en}
}
@article{UlmerBraunChengetal.2020,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Human-Centered Gamification Framework for Manufacturing Systems},
  series = {Procedia CIRP},
  volume    = {93},
  journal   = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2020.04.076},
  pages     = {670 -- 675},
  year      = {2020},
  abstract  = {While bringing new opportunities, the Industry 4.0 movement also imposes new challenges to the manufacturing industry and all its stakeholders. In this competitive environment, a skilled and engaged workforce is a key to success. Gamification can generate valuable feedbacks for improving employees' engagement and performance. Currently, Gamification in workspaces focuses on computer-based assignments and training, while tasks that require manual labor are rarely considered. This research provides an overview of Enterprise Gamification approaches and evaluates the challenges. Based on that, a skill-based Gamification framework for manual tasks is proposed, and a case study in the Industry 4.0 model factory is shown.},
  language  = {en}
}