@misc{FeldmannFranckeEspeetal.2022,
  author    = {Feldmann, Marco and Francke, Gero and Espe, Clemes and Chen, Qian and Baader, Fabian and Boxberg, Marc S. and Sustrate, Anna-Marie and Kowalski, Julia and Dachwald, Bernd},
  title     = {Performance data of an ice-melting probe from field tests in two different ice environments},
  doi       = {10.5281/zenodo.6094866},
  year      = {2022},
  abstract  = {This dataset was acquired at field tests of the steerable ice-melting probe "EnEx-IceMole" (Dachwald et al., 2014). A field test in summer 2014 was used to test the melting probe's system, before the probe was shipped to Antarctica, where, in international cooperation with the MIDGE project, the objective of a sampling mission in the southern hemisphere summer 2014/2015 was to return a clean englacial sample from the subglacial brine reservoir supplying the Blood Falls at Taylor Glacier (Badgeley et al., 2017, German et al., 2021). The standardized log-files generated by the IceMole during melting operation include more than 100 operational parameters, housekeeping information, and error states, which are reported to the base station in intervals of 4 s. Occasional packet loss in data transmission resulted in a sparse number of increased sampling intervals, which where compensated for by linear interpolation during post processing. The presented dataset is based on a subset of this data: The penetration distance is calculated based on the ice screw drive encoder signal, providing the rate of rotation, and the screw's thread pitch. The melting speed is calculated from the same data, assuming the rate of rotation to be constant over one sampling interval. The contact force is calculated from the longitudinal screw force, which es measured by strain gauges. The used heating power is calculated from binary states of all heating elements, which can only be either switched on or off. Temperatures are measured at each heating element and averaged for three zones (melting head, side-wall heaters and back-plate heaters).},
  language  = {en}
}
@article{Finger2016,
  author    = {Finger, Felix},
  title     = {Senkrechtstarter: FH-Absolvent wird f{\"u}r Transportdrohne ausgezeichnet},
  series = {campushunter: das etwas andere Karrieremagazin - Wintersemester 16/17},
  journal   = {campushunter: das etwas andere Karrieremagazin - Wintersemester 16/17},
  number    = {17. Regionalausgabe Aachen},
  publisher = {Campushunter Media},
  address   = {Heidelberg},
  issn      = {2196-9426},
  pages     = {116 -- 117},
  year      = {2016},
  language  = {de}
}
@inproceedings{Finger2016,
  author    = {Finger, Felix},
  title     = {Comparative Performance and Benefit Assessment of VTOL and CTOL UAVs},
  series = {Deutscher Luft- und Raumfahrtkongress (DLRK) 2016, 13.-15.9.2016},
  booktitle = {Deutscher Luft- und Raumfahrtkongress (DLRK) 2016, 13.-15.9.2016},
  pages     = {10 Seiten},
  year      = {2016},
  language  = {en}
}
@article{Finger2017,
  author    = {Finger, Felix},
  title     = {Vergleichende Leistungs- und Nutzenbewertung von VTOL- und CTOL-UAVs},
  series = {Luft- und Raumfahrt : informieren, vernetzen, f{\"o}rdern / Hrsg.: Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt},
  volume    = {38},
  journal   = {Luft- und Raumfahrt : informieren, vernetzen, f{\"o}rdern / Hrsg.: Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt},
  number    = {1},
  issn      = {0173-6264},
  pages     = {44 -- 47},
  year      = {2017},
  language  = {de}
}
@article{FingerBilBraun2019,
  author    = {Finger, Felix and Bil, Cees and Braun, Carsten},
  title     = {Initial Sizing Methodology for Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {2},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035428},
  pages     = {245 -- 255},
  year      = {2019},
  language  = {en}
}
@inproceedings{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1502},
  pages     = {15 Seiten},
  year      = {2020},
  abstract  = {As battery technologies advance, electric propulsion concepts are on the edge of disrupting aviation markets. However, until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial-hybrid-, parallel-hybrid-, fully-electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This paper provides insight into some factors that drive a new design towards either conventional or hybrid propulsion systems. General aviation aircraft, VTOL air taxis, transport aircraft, and UAVs are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their take-off mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints (e.g. take-off, climb). However, if the propulsion system is sized by a continuous power requirement (e.g. cruise), hybrid-electric systems offer hardly any benefit.},
  language  = {en}
}
@inproceedings{FingerBraunBil2019,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Engine Failure Constraints on the Initial Sizing of Hybrid-Electric GA Aircraft},
  series = {AIAA Scitech 2019 Forum},
  booktitle = {AIAA Scitech 2019 Forum},
  doi       = {10.2514/6.2019-1812},
  year      = {2019},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Battery Performance on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aerospace Engineering},
  volume    = {33},
  journal   = {Journal of Aerospace Engineering},
  number    = {3},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001113},
  year      = {2020},
  abstract  = {Studies suggest that hybrid-electric aircraft have the potential to generate fewer emissions and be inherently quieter when compared to conventional aircraft. By operating combustion engines together with an electric propulsion system, synergistic benefits can be obtained. However, the performance of hybrid-electric aircraft is still constrained by a battery's energy density and discharge rate. In this paper, the influence of battery performance on the gross mass for a four-seat general aviation aircraft with a hybrid-electric propulsion system is analyzed. For this design study, a high-level approach is chosen, using an innovative initial sizing methodology to determine the minimum required aircraft mass for a specific set of requirements and constraints. Only the peak-load shaving operational strategy is analyzed. Both parallel- and serial-hybrid propulsion configurations are considered for two different missions. The specific energy of the battery pack is varied from 200 to 1,000 W⋅h/kg, while the discharge time, and thus the normalized discharge rating (C-rating), is varied between 30 min (2C discharge rate) and 2 min (30C discharge rate). With the peak-load shaving operating strategy, it is desirable for hybrid-electric aircraft to use a light, low capacity battery system to boost performance. For this case, the battery's specific power rating proved to be of much higher importance than for full electric designs, which have high capacity batteries. Discharge ratings of 20C allow a significant take-off mass reduction aircraft. The design point moves to higher wing loadings and higher levels of hybridization if batteries with advanced technology are used.},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {5},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035897},
  year      = {2020},
  abstract  = {Until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial hybrid-electric, parallel hybrid-electric, fully electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This Paper provides insight into some factors that drive a new design toward either conventional or hybrid propulsion systems. General aviation aircraft, regional transport aircraft vertical takeoff and landing air taxis, and unmanned aerial vehicles are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their takeoff mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Only parallel-hybrid-electric powertrains are taken into account. Aeropropulsive interaction effects are neglected. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints. However, if the propulsion system is sized by a continuous power requirement, hybrid-electric systems offer hardly any benefit.},
  language  = {en}
}
@inproceedings{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Case studies in initial sizing for hybrid-electric general aviation aircraft},
  series = {2018 AIAA/IEEE Electric Aircraft Technologies Symposium, Cincinnati, Ohio},
  booktitle = {2018 AIAA/IEEE Electric Aircraft Technologies Symposium, Cincinnati, Ohio},
  doi       = {10.2514/6.2018-5005},
  year      = {2018},
  language  = {en}
}