@article{HeinkeKnickerAlbracht2021,
  author    = {Heinke, Lars N. and Knicker, Axel J. and Albracht, Kirsten},
  title     = {Test-retest reliability of the internal shoulder rotator muscles' stretch reflex in healthy men},
  series = {Journal of Electromyography and Kinesiology},
  volume    = {62},
  journal   = {Journal of Electromyography and Kinesiology},
  number    = {Article 102611},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1050-6411},
  doi       = {10.1016/j.jelekin.2021.102611},
  year      = {2021},
  abstract  = {Until now the reproducibility of the short latency stretch reflex of the internal rotator muscles of the glenohumeral joint has not been identified. Twenty-three healthy male participants performed three sets of external shoulder rotation stretches with various pre-activation levels on two different dates of measurement to assess test-retest reliability. All stretches were applied with a dynamometer acceleration of 104°/s2 and a velocity of 150°/s. Electromyographical response was measured via surface EMG. Reflex latencies showed a pre-activation effect (ƞ2 = 0,355). ICC ranged from 0,735 to 0,909 indicating an overall "good" relative reliability. SRD 95\% lay between ±7,0 to ±12,3 ms.. The reflex gain showed overall poor test-retest reproducibility. The chosen methodological approach presented a suitable test protocol for shoulder muscles stretch reflex latency evaluation. A proof-of-concept study to validate the presented methodical approach in shoulder involvement including subjects with clinically relevant conditions is recommended.},
  language  = {en}
}
@article{WaldvogelRitzmannFreyleretal.2021,
  author    = {Waldvogel, Janice and Ritzmann, Ramona and Freyler, Kathrin and Helm, Michael and Monti, Elena and Albracht, Kirsten and St{\"a}udle, Benjamin and Gollhofer, Albert and Narici, Marco},
  title     = {The Anticipation of Gravity in Human Ballistic Movement},
  series = {Frontiers in Physiology},
  journal   = {Frontiers in Physiology},
  publisher = {Frontiers},
  address   = {Lausanne},
  issn      = {1664-042X},
  doi       = {10.3389/fphys.2021.614060},
  year      = {2021},
  abstract  = {Stretch-shortening type actions are characterized by lengthening of the pre-activated muscle-tendon unit (MTU) in the eccentric phase immediately followed by muscle shortening. Under 1 g, pre-activity before and muscle activity after ground contact, scale muscle stiffness, which is crucial for the recoil properties of the MTU in the subsequent push-off. This study aimed to examine the neuro-mechanical coupling of the stretch-shortening cycle in response to gravity levels ranging from 0.1 to 2 g. During parabolic flights, 17 subjects performed drop jumps while electromyography (EMG) of the lower limb muscles was combined with ultrasound images of the gastrocnemius medialis, 2D kinematics and kinetics to depict changes in energy management and performance. Neuro-mechanical coupling in 1 g was characterized by high magnitudes of pre-activity and eccentric muscle activity allowing an isometric muscle behavior during ground contact. EMG during pre-activity and the concentric phase systematically increased from 0.1 to 1 g. Below 1 g the EMG in the eccentric phase was diminished, leading to muscle lengthening and reduced MTU stretches. Kinetic energy at take-off and performance were decreased compared to 1 g. Above 1 g, reduced EMG in the eccentric phase was accompanied by large MTU and muscle stretch, increased joint flexion amplitudes, energy loss and reduced performance. The energy outcome function established by linear mixed model reveals that the central nervous system regulates the extensor muscles phase- and load-specifically. In conclusion, neuro-mechanical coupling appears to be optimized in 1 g. Below 1 g, the energy outcome is compromised by reduced muscle stiffness. Above 1 g, loading progressively induces muscle lengthening, thus facilitating energy dissipation.},
  language  = {en}
}
@article{Kleefeld2021,
  author    = {Kleefeld, Andreas},
  title     = {The hot spots conjecture can be false: some numerical examples},
  series = {Advances in Computational Mathematics},
  volume    = {47},
  journal   = {Advances in Computational Mathematics},
  publisher = {Springer},
  address   = {Dordrecht},
  issn      = {1019-7168},
  doi       = {10.1007/s10444-021-09911-5},
  year      = {2021},
  abstract  = {The hot spots conjecture is only known to be true for special geometries. This paper shows numerically that the hot spots conjecture can fail to be true for easy to construct bounded domains with one hole. The underlying eigenvalue problem for the Laplace equation with Neumann boundary condition is solved with boundary integral equations yielding a non-linear eigenvalue problem. Its discretization via the boundary element collocation method in combination with the algorithm by Beyn yields highly accurate results both for the first non-zero eigenvalue and its corresponding eigenfunction which is due to superconvergence. Additionally, it can be shown numerically that the ratio between the maximal/minimal value inside the domain and its maximal/minimal value on the boundary can be larger than 1 + 10- 3. Finally, numerical examples for easy to construct domains with up to five holes are provided which fail the hot spots conjecture as well.},
  language  = {en}
}
@article{BerneckerBoyerGathmann2021,
  author    = {Bernecker, Andreas and Boyer, Pierre C. and Gathmann, Christina},
  title     = {The Role of Electoral Incentives for Policy Innovation: Evidence from the US Welfare Reform},
  series = {American Economic Journal: Economic Policy},
  volume    = {13},
  journal   = {American Economic Journal: Economic Policy},
  number    = {2},
  publisher = {American Economic Association},
  address   = {Nashville, Tenn.},
  issn      = {1945-774X},
  doi       = {10.1257/pol.20190690},
  pages     = {26 -- 57},
  year      = {2021},
  language  = {en}
}
@article{HagenkampBlankeDoering2021,
  author    = {Hagenkamp, Markus and Blanke, Tobias and D{\"o}ring, Bernd},
  title     = {Thermoelectric building temperature control: a potential assessment},
  series = {International Journal of Energy and Environmental Engineering},
  volume    = {13},
  journal   = {International Journal of Energy and Environmental Engineering},
  publisher = {Springer},
  address   = {Berlin},
  doi       = {10.1007/s40095-021-00424-x},
  pages     = {241 -- 254},
  year      = {2021},
  abstract  = {This study focuses on thermoelectric elements (TEE) as an alternative for room temperature control. TEE are semi-conductor devices that can provide heating and cooling via a heat pump effect without direct noise emissions and no refrigerant use. An efficiency evaluation of the optimal operating mode is carried out for different numbers of TEE, ambient temperatures, and heating loads. The influence of an additional heat recovery unit on system efficiency and an unevenly distributed heating demand are examined. The results show that TEE can provide heat at a coefficient of performance (COP) greater than one especially for small heating demands and high ambient temperatures. The efficiency increases with the number of elements in the system and is subject to economies of scale. The best COP exceeds six at optimal operating conditions. An additional heat recovery unit proves beneficial for low ambient temperatures and systems with few TEE. It makes COPs above one possible at ambient temperatures below 0 ∘C. The effect increases efficiency by maximal 0.81 (from 1.90 to 2.71) at ambient temperature 5 K below room temperature and heating demand Q˙h=100W but is subject to diseconomies of scale. Thermoelectric technology is a valuable option for electricity-based heat supply and can provide cooling and ventilation functions. A careful system design as well as an additional heat recovery unit significantly benefits the performance. This makes TEE superior to direct current heating systems and competitive to heat pumps for small scale applications with focus on avoiding noise and harmful refrigerants.},
  language  = {en}
}
@inproceedings{KernImaniVashianiTimmermanns2021,
  author    = {Kern, Alexander and Imani Vashiani, Anahita and Timmermanns, Tobias},
  title     = {Threat for human beings due to touch voltages and body currents caused by direct lightning strikes in case of non-isolated lightning protection systems using natural components},
  series = {35th International Conference on Lightning Protection (ICLP) and XVI International Symposium on Lightning Protection (SIPDA)},
  booktitle = {35th International Conference on Lightning Protection (ICLP) and XVI International Symposium on Lightning Protection (SIPDA)},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {978-1-6654-2346-5},
  doi       = {10.1109/ICLPandSIPDA54065.2021.9627465},
  pages     = {8 Seiten},
  year      = {2021},
  abstract  = {For typical cases of non-isolated lightning protection systems (LPS) the impulse currents are investigated which may flow through a human body directly touching a structural part of the LPS. Based on a basic LPS model with conventional down-conductors especially the cases of external and internal steel columns and metal fa{\c{c}}ades are considered and compared. Numerical simulations of the line quantities voltages and currents in the time domain are performed with an equivalent circuit of the entire LPS. As a result it can be stated that by increasing the number of conventional down-conductors and external steel columns the threat for a human being can indeed be reduced, but not down to an acceptable limit. In case of internal steel columns used as natural down-conductors the threat can be reduced sufficiently, depending on the low-resistive connection of the steel columns to the lightning equipotential bonding or the earth termination system, resp. If a metal fa{\c{c}}ade is used the threat for human beings touching is usually very low, if the fa{\c{c}}ade is sufficiently interconnected and multiply connected to the lightning equipotential bonding or the earth termination system, resp.},
  language  = {en}
}
@article{KoehlerRoepkeWolf2021,
  author    = {K{\"o}hler, Klemens and R{\"o}pke, Ren{\´e} and Wolf, Martin R.},
  title     = {Through a mirror darkly - On the obscurity of teaching goals in game-based learning in IT security},
  series = {ISAGA 2019: Simulation Gaming Through Times and Disciplines},
  journal   = {ISAGA 2019: Simulation Gaming Through Times and Disciplines},
  publisher = {Springer},
  address   = {Cham},
  doi       = {10.1007/978-3-030-72132-9_6},
  pages     = {61 -- 73},
  year      = {2021},
  abstract  = {Teachers and instructors use very specific language communicating teaching goals. The most widely used frameworks of common reference are the Bloom's Taxonomy and the Revised Bloom's Taxonomy. The latter provides distinction of 209 different teaching goals which are connected to methods. In Competence Developing Games (CDGs - serious games to convey knowledge) and in IT security education, a two- or three level typology exists, reducing possible learning outcomes to awareness, training, and education. This study explores whether this much simpler framework succeeds in achieving the same range of learning outcomes. Method wise a keyword analysis was conducted. The results were threefold: 1. The words used to describe teaching goals in CDGs on IT security education do not reflect the whole range of learning outcomes. 2. The word choice is nevertheless different from common language, indicating an intentional use of language. 3. IT security CDGs use different sets of terms to describe learning outcomes, depending on whether they are awareness, training, or education games. The interpretation of the findings is that the reduction to just three types of CDGs reduces the capacity to communicate and think about learning outcomes and consequently reduces the outcomes that are intentionally achieved.},
  language  = {en}
}
@article{HugenrothNeidlinEngelmannetal.2021,
  author    = {Hugenroth, Kristin and Neidlin, Michael and Engelmann, Ulrich M. and Kaufmann, Tim A. S. and Steinseifer, Ulrich and Heilmann, Torsten},
  title     = {Tipless Transseptal Cannula Concept Combines Improved Hemodynamic Properties and Risk-Reduced Placement: an In Silico Proof-of-Concept},
  series = {Artificial Organs},
  journal   = {Artificial Organs},
  number    = {Accepted Article},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1525-1594},
  doi       = {10.1111/aor.13964},
  year      = {2021},
  language  = {en}
}
@article{MolinnusDrinicIkenetal.2021,
  author    = {Molinnus, Denise and Drinic, Aleksander and Iken, Heiko and Kr{\"o}ger, Nadja and Zinser, Max and Smeets, Ralf and K{\"o}pf, Marius and Kopp, Alexander and Sch{\"o}ning, Michael Josef},
  title     = {Towards a flexible electrochemical biosensor fabricated from biocompatible Bombyx mori silk},
  series = {Biosensors and Bioelectronics},
  volume    = {183},
  journal   = {Biosensors and Bioelectronics},
  number    = {Art. 113204},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0956-5663},
  doi       = {10.1016/j.bios.2021.113204},
  year      = {2021},
  language  = {en}
}
@article{BechtSchollmayerMonakhovaetal.2021,
  author    = {Becht, Alexander and Schollmayer, Curd and Monakhova, Yulia and Holzgrabe, Ulrike},
  title     = {Tracing the origin of paracetamol tablets by near-infrared, mid-infrared, and nuclear magnetic resonance spectroscopy using principal component analysis and linear discriminant analysis},
  series = {Analytical and Bioanalytical Chemistry},
  volume    = {413},
  journal   = {Analytical and Bioanalytical Chemistry},
  publisher = {Springer Nature},
  issn      = {1618-2650},
  doi       = {10.1007/s00216-021-03249-z},
  pages     = {3107 -- 3118},
  year      = {2021},
  abstract  = {Most drugs are no longer produced in their own countries by the pharmaceutical companies, but by contract manufacturers or at manufacturing sites in countries that can produce more cheaply. This not only makes it difficult to trace them back but also leaves room for criminal organizations to fake them unnoticed. For these reasons, it is becoming increasingly difficult to determine the exact origin of drugs. The goal of this work was to investigate how exactly this is possible by using different spectroscopic methods like nuclear magnetic resonance and near- and mid-infrared spectroscopy in combination with multivariate data analysis. As an example, 56 out of 64 different paracetamol preparations, collected from 19 countries around the world, were chosen to investigate whether it is possible to determine the pharmaceutical company, manufacturing site, or country of origin. By means of suitable pre-processing of the spectra and the different information contained in each method, principal component analysis was able to evaluate manufacturing relationships between individual companies and to differentiate between production sites or formulations. Linear discriminant analysis showed different results depending on the spectral method and purpose. For all spectroscopic methods, it was found that the classification of the preparations to their manufacturer achieves better results than the classification to their pharmaceutical company. The best results were obtained with nuclear magnetic resonance and near-infrared data, with 94.6\%/99.6\% and 98.7/100\% of the spectra of the preparations correctly assigned to their pharmaceutical company or manufacturer.},
  language  = {en}
}