@article{YazdanbakhshSolbachBitz2012,
  author    = {Yazdanbakhsh, Pedram and Solbach, Klaus and Bitz, Andreas},
  title     = {Variable power combiner for RF mode shimming in 7-T MR imaging},
  series = {IEEE Transaction on Biomedical Engineering},
  volume    = {59},
  journal   = {IEEE Transaction on Biomedical Engineering},
  number    = {9},
  publisher = {IEEE},
  address   = {New York},
  issn      = {1558-2531},
  doi       = {10.1109/TBME.2012.2205926},
  pages     = {2549 -- 2557},
  year      = {2012},
  abstract  = {This contribution discusses the utilization of RF power in an MRI system with RF mode shimming which enables the superposition of circularly polarized modes of a transmit RF coil array driven by a Butler matrix. Since the required power for the individual modes can vary widely, mode-shimming can result in a significant underutilization of the total available RF power. A variable power combiner (VPC) is proposed to improve the power utilization: it can be realized as a reconfiguration of the MRI transmit system by the inclusion of one additional matrix network which receives the power from all transmit amplifiers at its input ports and provides any desired (combined) power distribution at its output ports by controlling the phase and amplitude of the amplifiers' input signals. The power distribution at the output ports of the VPC is then fed into the "mode" ports of the coil array Butler matrix in order to superimpose the spatial modes at the highest achievable power utilization. The VPC configuration is compared to the standard configuration of the transmit chain of our MRI system with 8 transmit channels and 16 coils. In realistic scenarios, improved power utilization was achieved from 17\% to 60\% and from 14\% to 55\% for an elliptical phantom and a region of interest in the abdomen, respectively, and an increase of the power utilization of 1 dB for a region of interest in the upper leg. In general, it is found that the VPC allows significant improvement in power utilization when the shimming solution demands only a few modes to be energized, while the technique can yield loss in power utilization in cases with many modes required at high power level.},
  language  = {en}
}
@article{Huening2012,
  author    = {H{\"u}ning, Felix},
  title     = {Using Trench PowerMOSFETs in Linear Mode},
  series = {Power Electronics Europe (2012)},
  journal   = {Power Electronics Europe (2012)},
  publisher = {DFA Media},
  address   = {Tonbridge},
  issn      = {1748-3530},
  pages     = {27 -- 29},
  year      = {2012},
  abstract  = {If we think about applications for modern Power MOSFETs using trench technology, running them in linear mode may not be top of the priority list. Yet there are multiple uses for Trench Power MOSFETs in linear mode. In fact, even turning the device on and off in switching applications is a form of linear operation. Also, these components can be run in linear mode to protect the device against voltage surges. This article will illustrate the factors that need to be considered for linear operation and show how Trench Power MOSFETs are suited to it.},
  language  = {en}
}
@inproceedings{FuchsRitzStrauch2012,
  author    = {Fuchs, Britta and Ritz, Thomas and Strauch, Jakob},
  title     = {Usability of mobile applications : dissemination of usability engineering in small and medium enterprises},
  series = {Proceedings of the International Conference on Data Communication Networking, e-Business and Optical Communication Systems : Rome, Italy, 24 - 27 July, 2012 ; [integrated in the ICETE (International Conference on e-Business and Telecommunications)]},
  booktitle = {Proceedings of the International Conference on Data Communication Networking, e-Business and Optical Communication Systems : Rome, Italy, 24 - 27 July, 2012 ; [integrated in the ICETE (International Conference on e-Business and Telecommunications)]},
  editor    = {Obaidat, Mohammad S.},
  publisher = {SciTePress},
  address   = {[Lissabon]},
  isbn      = {978-989-8565-23-5},
  pages     = {272 -- 277},
  year      = {2012},
  language  = {en}
}
@article{OrzadaMaderwaldPoseretal.2012,
  author    = {Orzada, S. and Maderwald, S. and Poser, B. A. and Johst, S. and Kannengiesser, S. and Ladd, M. E. and Bitz, Andreas},
  title     = {Time-interleaved acquisition of modes: an analysis of SAR and image contrast implications},
  series = {Magnetic Resonance in Medicine},
  volume    = {67},
  journal   = {Magnetic Resonance in Medicine},
  number    = {4},
  publisher = {Wiley-Liss},
  address   = {New York},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.23081},
  pages     = {1033 -- 1041},
  year      = {2012},
  abstract  = {s the magnetic field strength and therefore the operational frequency in MRI are increased, the radiofrequency wavelength approaches the size of the human head/body, resulting in wave effects which cause signal decreases and dropouts. Especially, whole-body imaging at 7 T and higher is therefore challenging. Recently, an acquisition scheme called time-interleaved acquisition of modes has been proposed to tackle the inhomogeneity problems in high-field MRI. The basic premise is to excite two (or more) different Burn:x-wiley:07403194:media:MRM23081:tex2gif-stack-1 modes using static radiofrequency shimming in an interleaved acquisition, where the complementary radiofrequency patterns of the two modes can be exploited to improve overall signal homogeneity. In this work, the impact of time-interleaved acquisition of mode on image contrast as well as on time-averaged specific absorption rate is addressed in detail. Time-interleaved acquisition of mode is superior in Burn:x-wiley:07403194:media:MRM23081:tex2gif-stack-2 homogeneity compared with conventional radiofrequency shimming while being highly specific absorption rate efficient. Time-interleaved acquisition of modes can enable almost homogeneous high-field imaging throughout the entire field of view in PD, T2, and T2*-weighted imaging and, if a specified homogeneity criterion is met, in T1-weighted imaging as well.},
  language  = {en}
}
@phdthesis{Bragard2012,
  author    = {Bragard, Michael},
  title     = {The integrated emitter turn-off thyristor : an innovative MOS-gated high-power device. - (Aachener Beitr{\"a}ge des ISEA ; 62)},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8440-1152-4},
  pages     = {III, 164 S. : Ill., graph. Darst.},
  year      = {2012},
  abstract  = {This thesis introduces the Integrated Emitter Turn-Off (IETO) Thyristor as a new high-power device. Known state-of-the-art research activities like the Dual GCT, the ETO thyristor and the ICT were presented and critically reviewed. A comparison with commercialized solutions identifies the pros and cons of each type of device family. Based on this analysis, the IETO structure is proposed, covering most benefits of each device class. In particular the combination of a MOS-assisted turn-off with a thyristor-based device allows a voltage-controlled MOS switching and the low on-state voltage of the thyristors. The following synthesis of an IETO device stands on a three-dimensional field of optimization spanned by electric, mechanical and thermal aspects. From an electric point of view, the lowest possible parasitic inductance and resistance within the commutation path are optimization criteria. The mechanical construction has to withstand the required contact pressure of multiple kilo Newtons. Finally, thermal borders limit the maximum average current of the device. FEM simulations covering these three aspects are performed for several design proposals. An IETO prototype is constructed and measurements on various test benches attest thermal, mechanical and electric performance. A local decoupling of the external driver stage and the presspack housing is presented by a cable connection. This separation enables a thermal and mechanical independence, which is advantageous in terms of vibrations and thermal cycles including increased reliability. The electric pulse performance of the prototype device is a factor of 3.1 above today''s solutions. In single-pulse measurements, a current up to 1600 A was successfully turned off at 115°C with an active silicon area of 823 mm². One reason for this increased turn-off capability is the extremely low-inductive construction. Additional functionality of the IETO thyristor like over-current self-protection and defined short-circuit failure state are successfully verified.},
  language  = {en}
}
@inproceedings{LogenHoefkenSchuba2012,
  author    = {Logen, Steffen and H{\"o}fken, Hans and Schuba, Marko},
  title     = {Simplifying RAM Forensics : A GUI and Extensions for the Volatility Framework},
  series = {2012 Seventh International Conference on Availability, Reliability and Security (ARES), 20-24 August 2012, Prague, Czech Republic},
  booktitle = {2012 Seventh International Conference on Availability, Reliability and Security (ARES), 20-24 August 2012, Prague, Czech Republic},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-1-4673-2244-7},
  doi       = {10.1109/ARES.2012.12},
  pages     = {620 -- 624},
  year      = {2012},
  abstract  = {The Volatility Framework is a collection of tools for the analysis of computer RAM. The framework offers a multitude of analysis options and is used by many investigators worldwide. Volatility currently comes with a command line interface only, which might be a hinderer for some investigators to use the tool. In this paper we present a GUI and extensions for the Volatility Framework, which on the one hand simplify the usage of the tool and on the other hand offer additional functionality like storage of results in a database, shortcuts for long Volatility Framework command sequences, and entirely new commands based on correlation of data stored in the database.},
  language  = {en}
}
@inproceedings{EngelsSchnabel2012,
  author    = {Engels, Elmar and Schnabel, Holger},
  title     = {Rapid-control-prototyping of industrial drives for the sercos automation bus},
  series = {13th International Workshop on Mechatronics (MECATRONICS), 2012 9th France-Japan \& 7th Europe-Asia Congress on and Research and Education in Mechatronics (REM)},
  booktitle = {13th International Workshop on Mechatronics (MECATRONICS), 2012 9th France-Japan \& 7th Europe-Asia Congress on and Research and Education in Mechatronics (REM)},
  isbn      = {978-1-4673-4771-6},
  pages     = {177 -- 181},
  year      = {2012},
  abstract  = {This article describes the functionality of a MATLAB® library that can be used to develop motion-logic applications in MATLAB programming language for industrial drive and control systems using the well known sercos automation bus. Therewith MATLAB's functionality is extended to designing automation applications from single axis machines up to multi-kinematic robots.},
  language  = {en}
}
@inproceedings{NoetzoldUphuesWegeneretal.2012,
  author    = {N{\"o}tzold, K. and Uphues, A. and Wegener, R. and Soter, S. and Fink, K. and Bragard, Michael and Griessel, R.},
  title     = {Inverter based test setup for LVRT verification of a full-scale 2 MW wind power converter},
  series = {EPE Joint Wind Energy and T\&D Chapters Seminar : 28th and 29th of June 2012, in the Utzon Centre, Aalborg, Denmark ; papers, posters, presentations. - Session 2: Grid connection, compliance},
  booktitle = {EPE Joint Wind Energy and T\&D Chapters Seminar : 28th and 29th of June 2012, in the Utzon Centre, Aalborg, Denmark ; papers, posters, presentations. - Session 2: Grid connection, compliance},
  publisher = {EPE Association},
  address   = {Brussels},
  year      = {2012},
  language  = {en}
}
@article{KobusBitzUdenetal.2012,
  author    = {Kobus, Thiele and Bitz, Andreas and Uden, Mark J. van and Lagemaat, Miram W. and Rothgang, Eva and Orzada, Stephan and Heerschap, Arend and Scheenen, Tom W. J.},
  title     = {In vivo 31P MR spectroscopic imaging of the human prostate at 7 T: safety and feasibility},
  series = {Magnetic Resonance in Medicine},
  volume    = {68},
  journal   = {Magnetic Resonance in Medicine},
  number    = {6},
  publisher = {Wiley-Liss},
  address   = {New York},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.24175},
  pages     = {1683 -- 1695},
  year      = {2012},
  abstract  = {31P MR spectroscopic imaging of the human prostate provides information about phosphorylated metabolites that could be used for prostate cancer characterization. The sensitivity of a magnetic field strength of 7 T might enable 3D 31P MR spectroscopic imaging with relevant spatial resolution in a clinically acceptable measurement time. To this end, a 31P endorectal coil was developed and combined with an eight-channel 1H body-array coil to relate metabolic information to anatomical location. An extensive safety validation was performed to evaluate the specific absorption rate, the radiofrequency field distribution, and the temperature distribution of both coils. This validation consisted of detailed Finite Integration Technique simulations, confirmed by MR thermometry and Burn:x-wiley:07403194:media:MRM24175:tex2gif-stack-1 measurements in a phantom and in vivo temperature measurements. The safety studies demonstrated that the presence of the 31P endorectal coil had no influence on the specific absorption rate levels and temperature distribution of the external eight-channel 1H array coil. To stay within a 10 g averaged local specific absorption rate of 10 W/kg, a maximum time-averaged input power of 33 W for the 1H array coil was allowed. For transmitting with the 31P endorectal coil, our safety limit of less than 1°C temperature increase in vivo during a 15-min MR spectroscopic imaging experiment was reached at a time-averaged input power of 1.9 W. With this power setting, a second in vivo measurement was performed on a healthy volunteer. Using adiabatic excitation, 3D 31P MR spectroscopic imaging produced spectra from the entire prostate in 18 min with a spatial resolution of 4 cm3. The spectral resolution enabled the separate detection of phosphocholine, phosphoethanolamine, inorganic phosphate, and other metabolites that could play an important role in the characterization of prostate cancer.},
  language  = {en}
}
@book{WosnitzaHilgers2012,
  author    = {Wosnitza, Franz and Hilgers, Hans Gerd},
  title     = {Energieeffizienz und Energiemanagement : ein {\"U}berblick heutiger M{\"o}glichkeiten und Notwendigkeiten},
  publisher = {Springer Spektrum},
  address   = {Wiesbaden},
  isbn      = {978-3-8348-1941-3},
  pages     = {XVII, 548 S. : Ill., graph. Darst.},
  year      = {2012},
  language  = {en}
}