@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Wind-tunnel and CFD investigations of UAV landing gears and turrets - Improvements in empirical drag estimation},
  series = {Aerospace Science and Technology},
  volume    = {107},
  journal   = {Aerospace Science and Technology},
  number    = {Art. 106306},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1270-9638},
  doi       = {10.1016/j.ast.2020.106306},
  year      = {2020},
  abstract  = {This paper analyzes the drag characteristics of several landing gear and turret configurations that are representative of unmanned aircraft tricycle landing gears and sensor turrets. A variety of these components were constructed via 3D-printing and analyzed in a wind-tunnel measurement campaign. Both turrets and landing gears were attached to a modular fuselage that supported both isolated components and multiple components at a time. Selected cases were numerically investigated with a Reynolds-averaged Navier-Stokes approach that showed good accuracy when compared to wind-tunnel data. The drag of main gear struts could be significantly reduced via streamlining their cross-sectional shape and keeping load carrying capabilities similar. The attachment of wheels introduced interference effects that increased strut drag moderately but significantly increased wheel drag compared to isolated cases. Very similar behavior was identified for front landing gears. The drag of an electro-optical and infrared sensor turret was found to be much higher than compared to available data of a clean hemisphere-cylinder combination. This turret drag was merely influenced by geometrical features like sensor surfaces and the rotational mechanism. The new data of this study is used to develop simple drag estimation recommendations for main and front landing gear struts and wheels as well as sensor turrets. These recommendations take geometrical considerations and interference effects into account.},
  language  = {en}
}
@inproceedings{FingerBraunBil2017,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {The Impact of Electric Propulsion on the Performance of VTOL UAVs},
  series = {Deutscher Luft- und Raumfahrtkongress 2017, DLRK , M{\"u}nchen},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2017, DLRK , M{\"u}nchen},
  year      = {2017},
  language  = {en}
}
@inproceedings{RingsLudowicyFingeretal.2019,
  author    = {Rings, Ren{\´e} and Ludowicy, Jonas and Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Sensitivity Analysis of General Aviation Aircraft with Parallel Hybrid-Electric Propulsion Systems},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {14 Seiten},
  year      = {2019},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2019,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Gomez, Francisco and Bil, Cees},
  title     = {RANS Simulation Validation of a Small Sensor Turret for UAVs},
  series = {Journal of Aerospace Engineering},
  volume    = {32},
  journal   = {Journal of Aerospace Engineering},
  number    = {5},
  publisher = {ASCE},
  address   = {New York},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001055},
  pages     = {Article number 04019060},
  year      = {2019},
  abstract  = {Recent Unmanned Aerial Vehicle (UAV) design procedures rely on full aircraft steady-state Reynolds-Averaged-Navier-Stokes (RANS) analyses in early design stages. Small sensor turrets are included in such simulations, even though their aerodynamic properties show highly unsteady behavior. Very little is known about the effects of this approach on the simulation outcomes of small turrets. Therefore, the flow around a model turret at a Reynolds number of 47,400 is simulated with a steady-state RANS approach and compared to experimental data. Lift, drag, and surface pressure show good agreement with the experiment. The RANS model predicts the separation location too far downstream and shows a larger recirculation region aft of the body. Both characteristic arch and horseshoe vortex structures are visualized and qualitatively match the ones found by the experiment. The Reynolds number dependence of the drag coefficient follows the trend of a sphere within a distinct range. The outcomes indicate that a steady-state RANS model of a small sensor turret is able to give results that are useful for UAV engineering purposes but might not be suited for detailed insight into flow properties.},
  language  = {en}
}
@inproceedings{GoettenHavermannBraunetal.2018,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Gomez, Francisco and Bil, Cees},
  title     = {On the Applicability of Empirical Drag Estimation Methods for Unmanned Air Vehicle Design Read More: https://arc.aiaa.org/doi/10.2514/6.2018-3192},
  series = {2018 Aviation Technology, Integration, and Operations Conference, AIAA AVIATION Forum},
  booktitle = {2018 Aviation Technology, Integration, and Operations Conference, AIAA AVIATION Forum},
  issn      = {1533-385X},
  doi       = {10.2514/6.2018-3192},
  pages     = {Article 3192},
  year      = {2018},
  language  = {en}
}
@article{FingerGoettenBraunetal.2020,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Mass, primary energy, and cost: the impact of optimization objectives on the initial sizing of hybrid-electric general aviation aircraft},
  series = {CEAS Aeronautical Journal},
  volume    = {2020},
  journal   = {CEAS Aeronautical Journal},
  number    = {11},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {1869-5590},
  doi       = {10.1007/s13272-020-00449-8},
  pages     = {713 -- 730},
  year      = {2020},
  abstract  = {For short take-off and landing (STOL) aircraft, a parallel hybrid-electric propulsion system potentially offers superior performance compared to a conventional propulsion system, because the short-take-off power requirement is much higher than the cruise power requirement. This power-matching problem can be solved with a balanced hybrid propulsion system. However, there is a trade-off between wing loading, power loading, the level of hybridization, as well as range and take-off distance. An optimization method can vary design variables in such a way that a minimum of a particular objective is attained. In this paper, a comparison between the optimization results for minimum mass, minimum consumed primary energy, and minimum cost is conducted. A new initial sizing algorithm for general aviation aircraft with hybrid-electric propulsion systems is applied. This initial sizing methodology covers point performance, mission performance analysis, the weight estimation process, and cost estimation. The methodology is applied to the design of a STOL general aviation aircraft, intended for on-demand air mobility operations. The aircraft is sized to carry eight passengers over a distance of 500 km, while able to take off and land from short airstrips. Results indicate that parallel hybrid-electric propulsion systems must be considered for future STOL aircraft.},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Mass, Primary Energy, and Cost - The Impact of Optimization Objectives on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  doi       = {10.25967/490012},
  pages     = {1 -- 17},
  year      = {2019},
  language  = {en}
}
@article{FingerBilBraun2019,
  author    = {Finger, Felix and Bil, Cees and Braun, Carsten},
  title     = {Initial Sizing Methodology for Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {2},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035428},
  pages     = {245 -- 255},
  year      = {2019},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@inproceedings{LudowicyRingsFingeretal.2019,
  author    = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Propulsion Technology Levels on the Sizing and Energy Consumption for Serial HybridElectric General Aviation Aircraft},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {14 Seiten},
  year      = {2019},
  language  = {en}
}