@article{AlebouyehSamamiPieperBreitbachetal.2014,
  author    = {Alebouyeh Samami, Behzad and Pieper, Martin and Breitbach, Gerd and Hodapp, Josef},
  title     = {Heat production in the windings of the stators of electric machines under stationary condition},
  series = {Heat and mass transfer},
  volume    = {50},
  journal   = {Heat and mass transfer},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {0947-7411 (Print) ; 1432-1181 (E-Journal)},
  doi       = {10.1007/s00231-014-1371-8},
  pages     = {1707 -- 1716},
  year      = {2014},
  abstract  = {In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results.},
  language  = {en}
}
@inproceedings{PieperSchulz2014,
  author    = {Pieper, Martin and Schulz, Silvia},
  title     = {Teaching Simulation Methods with COMSOL Multiphysics},
  organization    = {COMSOL Conference <2014, Cambridge>},
  pages     = {7},
  year      = {2014},
  abstract  = {This paper describes two courses on simulation methods for graduate students: "Simulation Methods" and "Simulation and Optimization in Virtual Engineering" The courses were planned to teach young engineers how to work with simulation software as well as to understand the necessary mathematical background. As simulation software COMSOL is used. The main philosophy was to combine theory and praxis in a way that motivates the students. In addition "soft skills" should be improved. This was achieved by project work as final examination. As underlying didactical principle the ideas of Bloom's revised taxonomy were followed. The paper basically focusses on educational aspects, e.g. how to structure the course, plan the exercises, organize the project work and include practical COMSOL examples.},
  language  = {en}
}
@article{JildehWagnerSchoeningetal.2015,
  author    = {Jildeh, Zaid B. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Pieper, Martin},
  title     = {Simulating the electromagnetic-thermal treatment of thin aluminium layers for adhesion improvement},
  series = {Physica status solidi (a)},
  volume    = {Vol. 212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431893},
  pages     = {1234 -- 1241},
  year      = {2015},
  abstract  = {A composite layer material used in packaging industry is made from joining layers of different materials using an adhesive. An important processing step in the production of aluminium-containing composites is the surface treatment and consequent coating of adhesive material on the aluminium surface. To increase adhesion strength between aluminium layer and the adhesive material, the foil is heat treated. For efficient heating, induction heating was considered as state-of-the-art treatment process. Due to the complexity of the heating process and the unpredictable nature of the heating source, the control of the process is not yet optimised. In this work, a finite element analysis of the process was established and various process parameters were studied. The process was simplified and modelled in 3D. The numerical model contains an air domain, an aluminium layer and a copper coil fitted with a magnetic field concentrating material. The effect of changing the speed of the aluminium foil (or rolling speed) was studied with the change of the coil current. Statistical analysis was used for generating a general control equation of coil current with changing rolling speed.},
  language  = {en}
}
@inproceedings{KremersPieper2015,
  author    = {Kremers, Alexander and Pieper, Martin},
  title     = {Simulation and Verification of Bionic Heat Exchangers with COMSOL Multiphysics® Software},
  series = {COMSOL Conference 2015 User Presentations ; COMSOL Conference 2015 Grenoble October 14 - 16, 2015 - World Trade Center, Grenoble, France},
  booktitle = {COMSOL Conference 2015 User Presentations ; COMSOL Conference 2015 Grenoble October 14 - 16, 2015 - World Trade Center, Grenoble, France},
  publisher = {COMSOL},
  address   = {G{\"o}ttingen ; Berlin},
  pages     = {6 Seiten},
  year      = {2015},
  language  = {en}
}
@inproceedings{StollenwerkRiekeDahmenetal.2016,
  author    = {Stollenwerk, Dominik and Rieke, C. and Dahmen, Markus and Pieper, Martin},
  title     = {Biogas Production Modelling : A Control System Engineering Approach},
  series = {IOP Conference Series: Earth and Environmental Science. Bd. 32},
  booktitle = {IOP Conference Series: Earth and Environmental Science. Bd. 32},
  issn      = {1755-1315},
  doi       = {10.1088/1755-1315/32/1/012008},
  pages     = {012008/1 -- 012008/4},
  year      = {2016},
  language  = {en}
}
@incollection{GeislerPieper2017,
  author    = {Geisler, Simon and Pieper, Martin},
  title     = {Mathematik PLuS als E-Book. Kann ein E-Book zur Ingenieursmathematik alle Lerntypen ansprechen?},
  series = {Das elektronische Schulbuch 2016},
  booktitle = {Das elektronische Schulbuch 2016},
  publisher = {LIT Verlag},
  address   = {Berlin},
  isbn      = {978-3-643-13475-2},
  pages     = {99 -- 111},
  year      = {2017},
  language  = {de}
}
@incollection{PieperWaehlisch2017,
  author    = {Pieper, Martin and W{\"a}hlisch, Georg},
  title     = {Mehrwert von E-Learning durch f{\"a}cher{\"u}bergreifenden Einsatz},
  series = {Teaching is Touching the Future \& ePS 2016 - Kompetenzorientiertes Lehren, Lernen und Pr{\"u}fen},
  booktitle = {Teaching is Touching the Future \& ePS 2016 - Kompetenzorientiertes Lehren, Lernen und Pr{\"u}fen},
  publisher = {UVW Universit{\"a}tsverlag Webler},
  address   = {Bielefeld},
  isbn      = {978-3-946017-05-9},
  pages     = {193 -- 196},
  year      = {2017},
  language  = {de}
}
@book{Pieper2017,
  author    = {Pieper, Martin},
  title     = {Mathematische Optimierung: Eine Einf{\"u}hrung in die kontinuierliche Optimierung mit Beispielen},
  publisher = {Springer Fachmedien},
  address   = {Wiesbaden},
  isbn      = {978-3-658-16975-6},
  doi       = {10.1007/978-3-658-16975-6},
  pages     = {IX, 53 S. 20 Abb.},
  year      = {2017},
  language  = {de}
}
@article{RiekeStollenwerkDahmenetal.2018,
  author    = {Rieke, Christian and Stollenwerk, Dominik and Dahmen, Markus and Pieper, Martin},
  title     = {Modeling and optimization of a biogas plant for a demand-driven energy supply},
  series = {Energy},
  volume    = {145},
  journal   = {Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0360-5442},
  doi       = {10.1016/j.energy.2017.12.073},
  pages     = {657 -- 664},
  year      = {2018},
  abstract  = {Due to the Renewable Energy Act, in Germany it is planned to increase the amount of renewable energy carriers up to 60\%. One of the main problems is the fluctuating supply of wind and solar energy. Here biogas plants provide a solution, because a demand-driven supply is possible. Before running such a plant, it is necessary to simulate and optimize the process. This paper provides a new model of a biogas plant, which is as accurate as the standard ADM1 model. The advantage compared to ADM1 is that it is based on only four parameters compared to 28. Applying this model, an optimization was installed, which allows a demand-driven supply by biogas plants. Finally the results are confirmed by several experiments and measurements with a real test plant.},
  language  = {en}
}
@inproceedings{Pieper2018,
  author    = {Pieper, Martin},
  title     = {Digitale Hochschullehre in mathematischen und mathematikdidaktischen Veranstaltungen},
  series = {Beitr{\"a}ge zum Mathematikunterricht 2018 : Vortr{\"a}ge zur Mathematikdidaktik und zur Schnittstelle Mathematik/Mathematikdidaktik auf der gemeinsamen Jahrestagung GDM und DMV 2018 (52. Jahrestagung der Gesellschaft f{\"u}r Didaktik der Mathematik). Bd. 1},
  booktitle = {Beitr{\"a}ge zum Mathematikunterricht 2018 : Vortr{\"a}ge zur Mathematikdidaktik und zur Schnittstelle Mathematik/Mathematikdidaktik auf der gemeinsamen Jahrestagung GDM und DMV 2018 (52. Jahrestagung der Gesellschaft f{\"u}r Didaktik der Mathematik). Bd. 1},
  publisher = {WTM-Verlag},
  address   = {M{\"u}nster},
  isbn      = {978-3-95987-089-4},
  pages     = {105 -- 106},
  year      = {2018},
  language  = {de}
}