@article{HuckPoghossianWagneretal.2012,
  author    = {Huck, Christina and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Combined amperometric/field-effect sensor for the detection of dissolved hydrogen},
  series = {Sensors and actuators B: Chemical},
  volume    = {187},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2012.10.050},
  pages     = {168 -- 173},
  year      = {2012},
  abstract  = {Real-time and reliable monitoring of the biogas process is crucial for a stable and efficient operation of biogas production in order to avoid digester breakdowns. The concentration of dissolved hydrogen (H₂) represents one of the key parameters for biogas process control. In this work, a one-chip integrated combined amperometric/field-effect sensor for monitoring the dissolved H₂ concentration has been developed for biogas applications. The combination of two different transducer principles might allow a more accurate and reliable measurement of dissolved H₂ as an early warning indicator of digester failures. The feasibility of the approach has been demonstrated by simultaneous amperometric/field-effect measurements of dissolved H₂ concentrations in electrolyte solutions. Both, the amperometric and the field-effect transducer show a linear response behaviour in the H₂ concentration range from 0.1 to 3\% (v/v) with a slope of 198.4 ± 13.7 nA/\% (v/v) and 14.9 ± 0.5 mV/\% (v/v), respectively.},
  language  = {en}
}
@article{Weigand2012,
  author    = {Weigand, Christoph},
  title     = {Statistical Tests Based on Reliability and Precision},
  series = {Economic Quality Control : EQC ; international journal for quality and reliability},
  volume    = {27},
  journal   = {Economic Quality Control : EQC ; international journal for quality and reliability},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1869-6147},
  doi       = {10.1515/eqc-2012-0002},
  pages     = {43 -- 64},
  year      = {2012},
  abstract  = {The construction of a statistical test is investigated which is based only on "reliability" and "precision" as quality criteria. The reliability of a statistical test is quantifiedin a straightforward way by the probability that the decision of the test is correct. However, the quantification of the precision of a statistical test is not at all evident. Thereforethe paper presents and discusses several approaches. Moreover the distinction of "nullhypothesis" and "alternative hypothesis" is not necessary any longer.},
  language  = {en}
}
@article{FateriHoetterGebhardt2012,
  author    = {Fateri, Miranda and H{\"o}tter, Jan-Steffen and Gebhardt, Andreas},
  title     = {Experimental and Theoretical Investigation of Buckling Deformation of Fabricated Objects by Selective Laser Melting},
  series = {Physics Procedia},
  volume    = {39},
  journal   = {Physics Procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892},
  doi       = {10.1016/j.phpro.2012.10.062},
  pages     = {464 -- 470},
  year      = {2012},
  abstract  = {Although Selective Laser Melting (SLM) process is an innovative manufacturing method, there are challenges such as inferior mechanical properties of fabricated objects. Regarding this, buckling deformation which is caused by thermal stress is one of the undesired mechanical properties which must be alleviated. As buckling deformation is more observable in hard to process materials, silver is selected to be studied theoretically and experimentally for this paper. Different scanning strategies are utilized and a Finite Element Method (FEM) is applied to calculate the temperature gradient in order to determine its effect on the buckling deformation of the objects from experiments.},
  language  = {en}
}
@article{HasanKeilStaatetal.2012,
  author    = {Hasan, Istabrak and Keil, Ludger and Staat, Manfred and Wahl, Gerhard and Bourauel, Christoph},
  title     = {Determination of the frictional coefficient of the implant-antler interface : experimental approach},
  series = {Biomedical Engineering / Biomedizinische Technik},
  volume    = {57},
  journal   = {Biomedical Engineering / Biomedizinische Technik},
  number    = {5},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1862-278X},
  pages     = {359 -- 363},
  year      = {2012},
  abstract  = {The similar bone structure of reindeer antler to human bone permits studying the osseointegration of dental implants in the jawbone. As the friction is one of the major factors that have a significant influence on the initial stability of immediately loaded dental implants, it is essential to define the frictional coefficient of the implant-antler interface. In this study, the kinetic frictional forces at the implant-antler interface were measured experimentally using an optomechanical setup and a stepping motor controller under different axial loads and sliding velocities. The corresponding mean values of the static and kinetic frictional coefficients were within the range of 0.5-0.7 and 0.3-0.5, respectively. An increase in the frictional forces with increasing applied axial loads was registered. The measurements showed an evidence of a decrease in the magnitude of the frictional coefficient with increasing sliding velocity. The results of this study provide a considerable assessment to clarify the suitable frictional coefficient to be used in the finite element contact analysis of antler specimens.},
  language  = {en}
}
@book{WosnitzaHilgers2012,
  author    = {Wosnitza, Franz and Hilgers, Hans Gerd},
  title     = {Energieeffizienz und Energiemanagement : ein {\"U}berblick heutiger M{\"o}glichkeiten und Notwendigkeiten},
  publisher = {Springer Spektrum},
  address   = {Wiesbaden},
  isbn      = {978-3-8348-1941-3},
  pages     = {XVII, 548 S. : Ill., graph. Darst.},
  year      = {2012},
  language  = {en}
}
@book{JanserHavermann2012,
  author    = {Janser, Frank and Havermann, Marc},
  title     = {Inkompressible Str{\"o}mungen},
  publisher = {Mainz},
  address   = {Aachen},
  isbn      = {978-3-86130-446-3},
  pages     = {189 S. : Ill., graph. Darst.},
  year      = {2012},
  language  = {en}
}
@inproceedings{SchoppNachtrodtHeuermannetal.2012,
  author    = {Schopp, Christoph and Nachtrodt, Frederik and Heuermann, Holger and Scherer, Ulrich W. and Mostacci, Domiziano and Finger, Torsten and Tietsch, Wolfgang},
  title     = {A novel 2.45 GHz/200 W Microwave Plasma Jet for High Temperature Applications above 3600 K},
  series = {Journal of Physics : Conference Series},
  volume    = {406},
  booktitle = {Journal of Physics : Conference Series},
  number    = {012029},
  issn      = {1742-6596},
  pages     = {5},
  year      = {2012},
  language  = {en}
}
@inproceedings{NixFrotscherStaat2012,
  author    = {Nix, Yvonne and Frotscher, Ralf and Staat, Manfred},
  title     = {Implementation of the edge-based smoothed extended finite element method},
  series = {Proceedings 6th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012) Vienna, Austria, September 10-14, 2012},
  booktitle = {Proceedings 6th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012) Vienna, Austria, September 10-14, 2012},
  editor    = {Eberhardsteiner, J.},
  year      = {2012},
  language  = {en}
}
@inproceedings{FrotscherRaatschenStaat2012,
  author    = {Frotscher, Ralf and Raatschen, Hans-J{\"u}rgen and Staat, Manfred},
  title     = {Application of an edge-based smoothed finite element method on geometrically non-linear plates of non-linear material},
  series = {Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012)},
  booktitle = {Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012)},
  editor    = {Eberhardsteiner, J.},
  year      = {2012},
  language  = {en}
}
@inproceedings{DuongNguyenStaat2012,
  author    = {Duong, Minh Tuan and Nguyen, Nhu Huynh and Staat, Manfred},
  title     = {Numerical stability enhancement of modeling hyperelastic materials},
  series = {Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012)},
  booktitle = {Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012)},
  editor    = {Eberhardsteiner, J.},
  year      = {2012},
  language  = {en}
}