@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}
@techreport{HebelMerkensFeyerletal.2021,
  author    = {Hebel, Christoph and Merkens, Torsten and Feyerl, G{\"u}nter and Kemper, Hans and Busse, Daniel},
  title     = {Elektromobilit{\"a}t - Verbundprojekt "COSTARTebus": Comprehensive strategy to accelerate the integration of electric-buses into existing public transport systems - Teilprojekt A : Berichtszeitraum: 01.01.2018-31.10.2020},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  pages     = {219 Seiten},
  year      = {2021},
  language  = {de}
}
@techreport{ThomaLaarmannMerkensetal.2020,
  author    = {Thoma, Andreas and Laarmann, Lukas and Merkens, Torsten and Franzke, Till and M{\"o}hren, Felix and Buttermann, Lilly and van der Weem, Dirk and Fischer, Maximilian and Misch, Philipp and B{\"o}hme, Mirijam and R{\"o}th, Thilo and Hebel, Christoph and Ritz, Thomas and Franke, Marina and Braun, Carsten},
  title     = {Entwicklung eines intermodalen Mobilit{\"a}tskonzeptes f{\"u}r die Pilotregion NRW/Rhein-Maas Euregio und Schaffung voller Kundenakzeptanz durch Transfer von Standards aus dem PKW-Bereich auf ein Flugtaxi : Schlussbericht : Projektakronym: SkyCab (Kategorie B) : Laufzeit in Monaten: 6 : Hauptthema: Kategorie B: Innovative Ideen mit Bezug zu UAS/Flugtaxis},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {97 Seiten},
  year      = {2020},
  language  = {de}
}
@incollection{SchubaHoefken2022,
  author    = {Schuba, Marko and H{\"o}fken, Hans-Wilhelm},
  title     = {Cybersicherheit in Produktion, Automotive und intelligenten Geb{\"a}uden},
  series = {IT-Sicherheit - Technologien und Best Practices f{\"u}r die Umsetzung im Unternehmen},
  booktitle = {IT-Sicherheit - Technologien und Best Practices f{\"u}r die Umsetzung im Unternehmen},
  publisher = {Carl Hanser Verlag},
  address   = {M{\"u}nchen},
  isbn      = {978-3-446-47223-5},
  doi       = {10.3139/9783446473478.012},
  pages     = {193 -- 218},
  year      = {2022},
  language  = {de}
}
@incollection{EnglaenderKaminskiSchuba2022,
  author    = {Engl{\"a}nder, Jacques and Kaminski, Lars and Schuba, Marko},
  title     = {Informationssicherheitsmanagement},
  series = {Digitalisierungs- und Informationsmanagement},
  booktitle = {Digitalisierungs- und Informationsmanagement},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-63757-9},
  doi       = {10.1007/978-3-662-63758-6_15},
  pages     = {373 -- 398},
  year      = {2022},
  abstract  = {Daten und Informationen sind die wichtigsten Ressourcen vieler Unternehmen und m{\"u}ssen daher entsprechend gesch{\"u}tzt werden. Getrieben durch die erh{\"o}hte Vernetzung von Informationstechnologie, die h{\"o}here Offenheit infolge datengetriebener Dienstleistungen und eine starke Zunahme an Datenquellen, r{\"u}cken die Gefahren von Informationsdiebstahl, -manipulation und -verlust in den Fokus von produzierenden Unternehmen. Auf dem Weg zum lern- und wandlungsf{\"a}higen Unternehmen kann dies zu einem großen Hindernis werden, da einerseits zu hohe Sicherheitsanforderungen neue Entwicklungen beschr{\"a}nken, andererseits wegen des Mangels an ausreichenden Informationssicherheitskonzepten Unternehmen weniger Innovationen wagen. Deshalb bedarf es individuell angepasster Konzepte f{\"u}r die Bereiche IT-Security, IT-Safety und Datenschutz f{\"u}r vernetzte Produkte, Produktion und Arbeitspl{\"a}tze. Bei der Entwicklung und Durchsetzung dieser Konzepte steht der Faktor Mensch im Zentrum aller {\"U}berlegungen. In diesem Kapitel wird dargestellt, wie der Faktor Mensch bei der Erstellung von Informationssicherheitskonzepten in verschiedenen Phasen zu beachten ist. Beginnend mit der Integration von Informationssystemen und damit verbundenen Sicherheitsmaßnahmen, {\"u}ber die Administration, bis hin zur Anwendung durch den Endnutzer, werden Methoden beschrieben, die den Menschen, verbunden mit seinem Mehrwert wie auch den Risiken, einschließen. Dabei werden sowohl Grundlagen aufgezeigt als auch Konzepte vorgestellt, mit denen Entscheider in der Unternehmens-IT Leitlinien f{\"u}r die Informationssicherheit festlegen k{\"o}nnen.},
  language  = {de}
}
@inproceedings{SchubaHoefkenLinzbach2022,
  author    = {Schuba, Marko and H{\"o}fken, Hans-Wilhelm and Linzbach, Sophie},
  title     = {An ICS Honeynet for Detecting and Analyzing Cyberattacks in Industrial Plants},
  series = {2021 International Conference on Electrical, Computer and Energy Technologies (ICECET)},
  booktitle = {2021 International Conference on Electrical, Computer and Energy Technologies (ICECET)},
  publisher = {IEEE},
  isbn      = {978-1-6654-4231-2},
  doi       = {10.1109/ICECET52533.2021.9698746},
  pages     = {6 Seiten},
  year      = {2022},
  abstract  = {Cybersecurity of Industrial Control Systems (ICS) is an important issue, as ICS incidents may have a direct impact on safety of people or the environment. At the same time the awareness and knowledge about cybersecurity, particularly in the context of ICS, is alarmingly low. Industrial honeypots offer a cheap and easy to implement way to raise cybersecurity awareness and to educate ICS staff about typical attack patterns. When integrated in a productive network, industrial honeypots may not only reveal attackers early but may also distract them from the actual important systems of the network. Implementing multiple honeypots as a honeynet, the systems can be used to emulate or simulate a whole Industrial Control System. This paper describes a network of honeypots emulating HTTP, SNMP, S7communication and the Modbus protocol using Conpot, IMUNES and SNAP7. The nodes mimic SIMATIC S7 programmable logic controllers (PLCs) which are widely used across the globe. The deployed honeypots' features will be compared with the features of real SIMATIC S7 PLCs. Furthermore, the honeynet has been made publicly available for ten days and occurring cyberattacks have been analyzed},
  language  = {en}
}
@inproceedings{ChristianMontagSchubaetal.2018,
  author    = {Christian, Esser and Montag, Tim and Schuba, Marko and Allhof, Manuel},
  title     = {Future critical infrastructure and security - cyberattacks on charging stations},
  series = {31st International Electric Vehicle Symposium \& Exhibition and International Electric Vehicle Technology Conference (EVS31 \& EVTeC 2018)},
  booktitle = {31st International Electric Vehicle Symposium \& Exhibition and International Electric Vehicle Technology Conference (EVS31 \& EVTeC 2018)},
  publisher = {Society of Automotive Engineers of Japan (JSAE)},
  address   = {Tokyo},
  isbn      = {978-1-5108-9157-9},
  pages     = {665 -- 671},
  year      = {2018},
  language  = {en}
}
@incollection{HebelHerrmannRitzetal.2022,
  author    = {Hebel, Christoph and Herrmann, Ulf and Ritz, Thomas and R{\"o}th, Thilo and Anthrakidis, Anette and B{\"o}ker, J{\"o}rg and Franzke, Till and Grodzki, Thomas and Merkens, Torsten and Sch{\"o}ttler, Mirjam},
  title     = {FlexSHARE - Methodisches Framework zur innovativen Gestaltung der urbanen Mobilit{\"a}t durch Sharing- Angebote},
  series = {Transforming Mobility - What Next?},
  booktitle = {Transforming Mobility - What Next?},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-36429-8},
  doi       = {10.1007/978-3-658-36430-4_10},
  pages     = {153 -- 169},
  year      = {2022},
  abstract  = {Das Ziel des INTERREG-Projektes „SHAREuregio" (FKZ: 34.EFRE-0300134) ist es, grenz{\"u}berschreitende Mobilit{\"a}t in der Euregio Rhein-Maas-Nord zu erm{\"o}glichen und zu f{\"o}rdern. Dazu soll ein elektromobiles Car- und Bikesharing- System entwickelt und in der Stadt M{\"o}nchengladbach, im Kreis Viersen sowie in den Gemeinden Roermond und Venlo (beide NL) zusammen mit den Partnern Wirtschaftsf{\"o}rderung M{\"o}nchengladbach, Wirtschaftsf{\"o}rderung f{\"u}r den Kreis Viersen, NEW AG, Goodmoovs (NL), Greenflux (NL) und der FH Aachen implementiert werden. Zun{\"a}chst richtet sich das Angebot, bestehend aus 40 Elektroautos und 40 Elektrofahrr{\"a}dern, an Unternehmen und wird nach einer Erprobungsphase, mit einer gr{\"o}ßeren Anzahl an Fahrzeugen, auch f{\"u}r Privatpersonen verf{\"u}gbar gemacht werden. Die Fahrzeuge stehen bei den jeweiligen Anwendungspartnern in Deutschland und den Niederlanden. Im Rahmen dieses Projektes hat die FH Aachen „FlexSHARE" entwickelt - ein methodisches Framework zur innovativen Gestaltung urbaner Sharing- Angebote. Das Framework erm{\"o}glicht es, anhand von messbaren Kenngr{\"o}ßen, bedarfsgerechte und auf die Region abgestimmte Sharing-Systeme zu entwickeln.},
  language  = {de}
}
@article{BergmannMoehrenBraunetal.2023,
  author    = {Bergmann, Ole and M{\"o}hren, Felix and Braun, Carsten and Janser, Frank},
  title     = {On the influence of elasticity on swept propeller noise},
  series = {AIAA SCITECH 2023 Forum},
  journal   = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-0210},
  year      = {2023},
  abstract  = {High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation.},
  language  = {en}
}
@inproceedings{GrundAltherr2023,
  author    = {Grund, Raphael M. and Altherr, Lena},
  title     = {Development of an open source energy disaggregation tool for the home automation platform Home Assistant},
  series = {Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel},
  booktitle = {Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel},
  editor    = {Reiff-Stephan, J{\"o}rg and J{\"a}kel, Jens and Schwarz, Andr{\´e}},
  publisher = {le-tex publishing services GmbH},
  address   = {Leipzig},
  isbn      = {978-3-910103-01-6},
  doi       = {10.33968/2023.02},
  pages     = {11 -- 20},
  year      = {2023},
  abstract  = {In order to reduce energy consumption of homes, it is important to make transparent which devices consume how much energy. However, power consumption is often only monitored aggregated at the house energy meter. Disaggregating this power consumption into the contributions of individual devices can be achieved using Machine Learning. Our work aims at making state of the art disaggregation algorithms accessibe for users of the open source home automation platform Home Assistant.},
  language  = {en}
}