@inproceedings{MarinkovicButenweg2020,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Seismic behaviour of RC frames with uncoupled masonry infills having two storeys or two bays},
  series = {Brick and Block Masonry - From Historical to Sustainable Masonry. Proceedings of the 17th International Brick/Block Masonry Conference},
  booktitle = {Brick and Block Masonry - From Historical to Sustainable Masonry. Proceedings of the 17th International Brick/Block Masonry Conference},
  publisher = {CRC Press},
  address   = {London},
  doi       = {10.1201/9781003098508-72},
  pages     = {1 -- 7},
  year      = {2020},
  abstract  = {Reinforced concrete (RC) structures with masonry infills are widely used for several types of buildings all over the world. However, it is well known that traditional masonry infills constructed with rigid contact to the surrounding RC frame performed rather poor in past earthquakes. Masonry infills showed severe in-plane damages and failed in many cases under out-of-plane seismic loading. As the undesired interactions between frames and infills changes the load transfer on building level, complete collapses of buildings were observed. A possible solution is uncoupling of masonry infills to the frame to reduce the infill contribution activated by the frame deformation under horizontal loading. The paper presents numerical simulations on RC frames equipped with the innovative decoupling system INODIS. The system was developed within the European project INSYSME and allows an effective uncoupling of frame and infill. The simulations are carried out with a micro-modelling approach, which is able to predict the complex nonlinear behaviour resulting from the different materials and their interaction. Each brick is modelled individually and connected taking into account nonlinearity of a brick mortar interface. The calibration of the model is based on small specimen tests and experimental results for one bay one storey frame are used for the validation. The validated model is further used for parametric studies on two storey and two bay infilled frames. The response and change of the structural stiffness are analysed and compared to the traditionally infilled frame. The results confirm the effectiveness of the INODIS system with less damage and relatively low contribution of the infill at high drift levels. In contrast to the uncoupled system configurations, traditionally infilled frames experienced brittle failure at rather low drift levels.},
  language  = {en}
}
@book{ButenwegHoffmeisterHoltschoppenetal.2020,
  author    = {Butenweg, Christoph and Hoffmeister, Benno and Holtschoppen, Britta and Klinkel, Sven and Rosin, Julia and Schmitt, Timo},
  title     = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {524 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{MarkinkovicButenwegPaveseetal.2020,
  author    = {Markinkovic, Marko and Butenweg, Christoph and Pavese, A. and Lanese, I. and Hoffmeister, B. and Pinkawa, M. and Vulcu, C. and Bursi, O. and Nardin, C. and Paolacci, F. and Quinci, G. and Fragiadakis, M. and Weber, F. and Huber, P. and Renault, P. and G{\"u}ndel, M. and Dyke, S. and Ciucci, M. and Marino, A.},
  title     = {Investigation of the seismic behaviour of structural and nonstructural components in industrial facilities by means of shaking table tests},
  series = {Seismic design of industrial facilities 2020},
  booktitle = {Seismic design of industrial facilities 2020},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {159 -- 172},
  year      = {2020},
  language  = {en}
}
@inproceedings{CacciatoreButenweg2020,
  author    = {Cacciatore, Pamela and Butenweg, Christoph},
  title     = {Seismic safety of cylindrical granular material steel silos under seismic loading},
  series = {Seismic design of industrial facilities 2020},
  booktitle = {Seismic design of industrial facilities 2020},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {231 -- 244},
  year      = {2020},
  language  = {en}
}
@inproceedings{MichelRosinButenwegetal.2020,
  author    = {Michel, Philipp and Rosin, Julia and Butenweg, Christoph and Klinkel, Sven},
  title     = {Soil-dependent earthquake spectra in the analysis of liquid-storage-tanks on compliant soil},
  series = {Seismic design of industrial facilities 2020},
  booktitle = {Seismic design of industrial facilities 2020},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {245 -- 254},
  year      = {2020},
  abstract  = {A further development of the Added-Mass-Method allows the combined representation of the effects of both soil-structure-interaction and fluid-structure interaction on a liquid-filled-tank in one model. This results in a practical method for describing the dynamic fluid pressure on the tank shell during joint movement. The fluid pressure is calculated on the basis of the tank's eigenform and the earthquake acceleration and represented by additional masses on the shell. The bearing on compliant ground is represented by replacement springs, which are calculated dependent on the local soil composition. The influence of the shear modulus of the compliant soil is clearly visible in the pressure curves and the stress distribution in the shell. The acceleration spectra are also dependent on soil stiffness. According to Eurocode-8 the acceleration spectra are determined for fixed soil-classes, instead of calculating the accelerations for each site in direct dependence on the soil composition. This leads to unrealistic sudden changes in the system's response. Therefore, earthquake spectra are calculated for different soil models in direct dependence of the shear modulus. Thus, both the acceleration spectra and the replacement springs match the soil composition. This enables a reasonable and consistent calculation of the system response for the actual conditions at each site.},
  language  = {en}
}
@article{HueningBackes2020,
  author    = {H{\"u}ning, Felix and Backes, Andreas},
  title     = {Direct observation of large Barkhausen jump in thin Vicalloy wires},
  series = {IEEE Magnetics Letters},
  volume    = {11},
  journal   = {IEEE Magnetics Letters},
  number    = {Art. 2506504},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {1949-307X},
  doi       = {10.1109/LMAG.2020.3046411},
  pages     = {1 -- 4},
  year      = {2020},
  language  = {en}
}
@article{GazdaMaurischat2020,
  author    = {Gazda, Quentin and Maurischat, Andreas},
  title     = {Special functions and Gauss-Thakur sums in higher rank and dimension},
  publisher = {De Gruyter},
  address   = {Berlin},
  pages     = {26 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{ChavezBermudezWollert2020,
  author    = {Chavez Bermudez, Victor Francisco and Wollert, J{\"o}rg},
  title     = {Arduino based Framework for Rapid Application Development of a Generic IO-Link interface},
  series = {Kommunikation und Bildverarbeitung in der Automation. Ausgew{\"a}hlte Beitr{\"a}ge der Jahreskolloquien KommA und BVAu 2018},
  booktitle = {Kommunikation und Bildverarbeitung in der Automation. Ausgew{\"a}hlte Beitr{\"a}ge der Jahreskolloquien KommA und BVAu 2018},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-59895-5},
  doi       = {10.1007/978-3-662-59895-5_2},
  pages     = {21 -- 33},
  year      = {2020},
  abstract  = {The implementation of IO-Link in the automation industry has increased over the years. Its main advantage is it offers a digital point-to-point plugand-play interface for any type of device or application. This simplifies the communication between devices and increases productivity with its different features like self-parametrization and maintenance. However, its complete potential is not always used. The aim of this paper is to create an Arduino based framework for the development of generic IO-Link devices and increase its implementation for rapid prototyping. By generating the IO device description file (IODD) from a graphical user interface, and further customizable options for the device application, the end-user can intuitively develop generic IO-Link devices. The peculiarity of this framework relies on its simplicity and abstraction which allows to implement any sensor functionality and virtually connect any type of device to an IO-Link master. This work consists of the general overview of the framework, the technical background of its development and a proof of concept which demonstrates the workflow for its implementation.},
  language  = {en}
}
@inproceedings{KaschSchmidtEichleretal.2020,
  author    = {Kasch, Susanne and Schmidt, Thomas and Eichler, Fabian and Thurn, Laura and Jahn, Simon and Bremen, Sebastian},
  title     = {Solution approaches and process concepts for powder bed-based melting of glass},
  series = {Industrializing Additive Manufacturing. Proceedings of AMPA2020},
  booktitle = {Industrializing Additive Manufacturing. Proceedings of AMPA2020},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-54333-4 (Print)},
  doi       = {10.1007/978-3-030-54334-1_7},
  pages     = {82 -- 95},
  year      = {2020},
  abstract  = {In the study, the process chain of additive manufacturing by means of powder bed fusion will be presented based on the material glass. In order to reliably process components additively, new concepts with different solutions were developed and investigated. Compared to established metallic materials, the properties of glass materials differ significantly. Therefore, the process control was adapted to the material glass in the investigations. With extensive parameter studies based on various glass powders such as borosilicate glass and quartz glass, scientifically proven results on powder bed fusion of glass are presented. Based on the determination of the particle properties with different methods, extensive investigations are made regarding the melting behavior of glass by means of laser beams. Furthermore, the experimental setup was steadily expanded. In addition to the integration of coaxial temperature measurement and regulation, preheating of the building platform is of major importance. This offers the possibility to perform 3D printing at the transformation temperatures of the glass materials. To improve the component's properties, the influence of a subsequent heat treatment was also investigated. The experience gained was incorporated into a new experimental system, which allows a much better exploration of the 3D printing of glass. Currently, studies are being conducted to improve surface texture, building accuracy, and geometrical capabilities using three-dimensional specimen. The contribution shows the development of research in the field of 3D printing of glass, gives an insight into the machine and process engineering as well as an outlook on the possibilities and applications.},
  language  = {en}
}
@inproceedings{AdamsLosekammCzupalla2020,
  author    = {Adams, Moritz and Losekamm, Martin J. and Czupalla, Markus},
  title     = {Development of the Thermal Control System for the RadMap Telescope Experiment on the International Space Station},
  series = {International Conference on Environmental Systems},
  booktitle = {International Conference on Environmental Systems},
  pages     = {1 -- 10},
  year      = {2020},
  language  = {en}
}