@article{FischerKowalskiPudasaini2012, author = {Fischer, Jan-Thomas and Kowalski, Julia and Pudasaini, Shiva P.}, title = {Topographic curvature effects in applied avalanche modelling}, series = {Cold Regions Science and Technology}, volume = {74-75}, journal = {Cold Regions Science and Technology}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-7441}, doi = {10.1016/j.coldregions.2012.01.005}, pages = {21 -- 30}, year = {2012}, abstract = {This paper describes the implementation of topographic curvature effects within the RApid Mass MovementS (RAMMS) snow avalanche simulation toolbox. RAMMS is based on a model similar to shallow water equations with a Coulomb friction relation and the velocity dependent Voellmy drag. It is used for snow avalanche risk assessment in Switzerland. The snow avalanche simulation relies on back calculation of observed avalanches. The calibration of the friction parameters depends on characteristics of the avalanche track. The topographic curvature terms are not yet included in the above mentioned classical model. Here, we fundamentally improve this model by mathematically and physically including the topographic curvature effects. By decomposing the velocity dependent friction into a topography dependent term that accounts for a curvature enhancement in the Coulomb friction, and a topography independent contribution similar to the classical Voellmy drag, we construct a general curvature dependent frictional resistance, and thus propose new extended model equations. With three site-specific examples, we compare the apparent frictional resistance of the new approach, which includes topographic curvature effects, to the classical one. Our simulation results demonstrate substantial effects of the curvature on the flow dynamics e.g., the dynamic pressure distribution along the slope. The comparison of resistance coefficients between the two models demonstrates that the physically based extension presents an improvement to the classical approach. Furthermore a practical example highlights its influence on the pressure outline in the run out zone of the avalanche. Snow avalanche dynamics modeling natural terrain curvature centrifugal force friction coefficients.}, language = {en} } @article{BuehlerChristenKowalskietal.2011, author = {B{\"u}hler, Yves and Christen, Marc and Kowalski, Julia and Bartelt, Perry}, title = {Sensitivity of snow avalanche simulations to digital elevation model quality and resolution}, series = {Annals of Glaciology}, volume = {52}, journal = {Annals of Glaciology}, number = {58}, publisher = {Cambridge University Press}, address = {Cambridge}, isbn = {1727-5644}, pages = {72 -- 80}, year = {2011}, abstract = {Digital elevation models (DEMs), represent the three-dimensional terrain and are the basic input for numerical snow avalanche dynamics simulations. DEMs can be acquired using topographic maps or remote-sensing technologies, such as photogrammetry or lidar. Depending on the acquisition technique, different spatial resolutions and qualities are achieved. However, there is a lack of studies that investigate the sensitivity of snow avalanche simulation algorithms to the quality and resolution of DEMs. Here, we perform calculations using the numerical avalance dynamics model RAMMS, varying the quality and spatial resolution of the underlying DEMs, while holding the simulation parameters constant. We study both channelized and open-terrain avalanche tracks with variable roughness. To quantify the variance of these simulations, we use well-documented large-scale avalanche events from Davos, Switzerland (winter 2007/08), and from our large-scale avalanche test site, Valĺee de la Sionne (winter 2005/06). We find that the DEM resolution and quality is critical for modeled flow paths, run-out distances, deposits, velocities and impact pressures. Although a spatial resolution of ~25 m is sufficient for large-scale avalanche modeling, the DEM datasets must be checked carefully for anomalies and artifacts before using them for dynamics calculations.}, language = {en} } @article{ChristenBarteltKowalski2010, author = {Christen, Marc and Bartelt, Perry and Kowalski, Julia}, title = {Back calculation of the In den Arelen avalanche with RAMMS: Interpretation of model results}, series = {Annals of Glaciology}, volume = {51}, journal = {Annals of Glaciology}, number = {54}, publisher = {Cambridge University Press}, address = {Cambridge}, isbn = {1727-5644}, doi = {10.3189/172756410791386553}, pages = {161 -- 168}, year = {2010}, abstract = {Two- and three-dimensional avalanche dynamics models are being increasingly used in hazard-mitigation studies. These models can provide improved and more accurate results for hazard mapping than the simple one-dimensional models presently used in practice. However, two- and three-dimensional models generate an extensive amount of output data, making the interpretation of simulation results more difficult. To perform a simulation in three-dimensional terrain, numerical models require a digital elevation model, specification of avalanche release areas (spatial extent and volume), selection of solution methods, finding an adequate calculation resolution and, finally, the choice of friction parameters. In this paper, the importance and difficulty of correctly setting up and analysing the results of a numerical avalanche dynamics simulation is discussed. We apply the two-dimensional simulation program RAMMS to the 1968 extreme avalanche event In den Arelen. We show the effect of model input variations on simulation results and the dangers and complexities in their interpretation.}, language = {en} } @article{ChristenKowalskiBartelt2010, author = {Christen, Marc and Kowalski, Julia and Bartelt, Perry}, title = {RAMMS: Numerical simulation of dense snow avalanches in three-dimensional terrain}, series = {Cold Regions Science and Technology}, volume = {63}, journal = {Cold Regions Science and Technology}, number = {1-2}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-7441}, doi = {10.1016/j.coldregions.2010.04.005}, pages = {1 -- 14}, year = {2010}, abstract = {Numerical avalanche dynamics models have become an essential part of snow engineering. Coupled with field observations and historical records, they are especially helpful in understanding avalanche flow in complex terrain. However, their application poses several new challenges to avalanche engineers. A detailed understanding of the avalanche phenomena is required to construct hazard scenarios which involve the careful specification of initial conditions (release zone location and dimensions) and definition of appropriate friction parameters. The interpretation of simulation results requires an understanding of the numerical solution schemes and easy to use visualization tools. We discuss these problems by presenting the computer model RAMMS, which was specially designed by the SLF as a practical tool for avalanche engineers. RAMMS solves the depth-averaged equations governing avalanche flow with accurate second-order numerical solution schemes. The model allows the specification of multiple release zones in three-dimensional terrain. Snow cover entrainment is considered. Furthermore, two different flow rheologies can be applied: the standard Voellmy-Salm (VS) approach or a random kinetic energy (RKE) model, which accounts for the random motion and inelastic interaction between snow granules. We present the governing differential equations, highlight some of the input and output features of RAMMS and then apply the models with entrainment to simulate two well-documented avalanche events recorded at the Vall{\´e}e de la Sionne test site.}, language = {en} } @article{FischerKowalskiPudasainietal.2009, author = {Fischer, Jan-Thomas and Kowalski, Julia and Pudasaini, Shiva P. and Miller, S. A.}, title = {Dynamic Avalanche Modeling in Natural Terrain}, series = {International Snow Science Workshop, Davos 2009, Proceedings ; Proc. ISSW 2009}, journal = {International Snow Science Workshop, Davos 2009, Proceedings ; Proc. ISSW 2009}, pages = {448 -- 452}, year = {2009}, abstract = {The powerful avalanche simulation toolbox RAMMS (Rapid Mass Movements) is based on a depth-averaged hydrodynamic system of equations with a Voellmy-Salm friction relation. The two empirical friction parameters μ and � correspond to a dry Coulomb friction and a viscous resistance, respectively. Although μ and � lack a proper physical explanation, 60 years of acquired avalanche data in the Swiss Alps made a systematic calibration possible. RAMMS can therefore successfully model avalanche flow depth, velocities, impact pressure and run out distances. Pudasaini and Hutter (2003) have proposed extended, rigorously derived model equations that account for local curvature and twist. A coordinate transformation into a reference system, applied to the actual mountain topography of the natural avalanche path, is performed. The local curvature and the twist of the avalanche path induce an additional term in the overburden pressure. This leads to a modification of the Coulomb friction, the free-surface pressure gradient, the pressure induced by the channel, and the gravity components along and normal to the curved and twisted reference surface. This eventually guides the flow dynamics and deposits of avalanches. In the present study, we investigate the influence of curvature on avalanche flow in real mountain terrain. Simulations of real avalanche paths are performed and compared for the different models approaches. An algorithm to calculate curvature in real terrain is introduced in RAMMS. This leads to a curvature dependent friction relation in an extended version of the Voellmy-Salm model equations. Our analysis provides yet another step in interpreting the physical meaning and significance of the friction parameters used in the RAMMS computational environment.}, language = {en} } @article{McArdellBarteltKowalski2007, author = {McArdell, Brian W. and Bartelt, Perry and Kowalski, Julia}, title = {Field observations of basal forces and fluid pore pressure in a debris flow}, series = {Geophysical Research Letters (GRL)}, volume = {34}, journal = {Geophysical Research Letters (GRL)}, number = {7}, isbn = {0094-8276}, year = {2007}, abstract = {Using results from an 8 m2 instrumented force plate we describe field measurements of normal and shear stresses, and fluid pore pressure for a debris flow. The flow depth increased from 0.1 to 1 m within the first 12 s of flow front arrival, remained relatively constant until 100 s, and then gradually decreased to 0.5 m by 600 s. Normal and shear stresses and pore fluid pressure varied in-phase with the flow depth. Calculated bulk densities are ρb = 2000-2250 kg m-3 for the bulk flow and ρf = 1600-1750 kg m-3 for the fluid phase. The ratio of effective normal stress to shear stress yields a Coulomb basal friction angle of ϕ = 26° at the flow front. We did not find a strong correlation between the degree of agitation in the flow, estimated using the signal from a geophone on the force plate, and an assumed dynamic pore fluid pressure. Our data support the idea that excess pore-fluid pressures are long lived in debris flows and therefore contribute to their unusual mobility.}, language = {en} } @article{HeierliPurvesFelberetal.2004, author = {Heierli, Joachim and Purves, Ross S. and Felber, Andreas and Kowalski, Julia}, title = {Verification of nearest-neighbours interpretations in avalanche forecasting}, series = {Annals of Glaciology}, volume = {38}, journal = {Annals of Glaciology}, number = {1}, isbn = {1727-5644}, pages = {84 -- 88}, year = {2004}, abstract = {This paper examines the positive and negative aspects of a range of interpretations of nearest-neighbours models. Measures-oriented and distributionoriented verification methods are applied to categorial, probabilistic and descriptive interpretations of nearest neighbours used operationally in avalanche forecasting in Scotland and Switzerland. The dependence of skill and accuracy measures on base rate is illustrated. The purpose of the forecast and the definition of events are important variables in determining the quality of the forecast. A discussion of the application of different interpretations in operational avalanche forecasting is presented.}, language = {en} } @article{Kowalski2008, author = {Kowalski, Julia}, title = {Mathematische Murgangmodellierung}, series = {Newsletter Naturgefahren}, volume = {2008}, journal = {Newsletter Naturgefahren}, number = {2}, organization = {Eidgen{\"o}ssisches Institut f{\"u}r Schnee-und Lawinenforschung SLF}, pages = {4 -- 5}, year = {2008}, language = {de} } @article{Mertens1985, author = {Mertens, Josef}, title = {Charakteristiken des Staub-Gas-Gemisches}, series = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4}, journal = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4}, isbn = {1521-4001}, pages = {T211 -- T213}, year = {1985}, language = {de} } @article{MertensKlevenhusenJakob1987, author = {Mertens, Josef and Klevenhusen, K. D. and Jakob, H.}, title = {Accurate Transonic Wave Drag Prediction Using Simple Physical Models}, series = {AIAA-Journal. 25 (1987), H. 6}, journal = {AIAA-Journal. 25 (1987), H. 6}, isbn = {0001-1452}, pages = {799 -- 805}, year = {1987}, language = {en} } @article{MertensRoeger2000, author = {Mertens, Josef and R{\"o}ger, Wolf}, title = {F-Schlepp: Problem Taumelschwingung}, series = {Aerokurier. 44 (2000), H. 10}, journal = {Aerokurier. 44 (2000), H. 10}, isbn = {0341-1281}, pages = {73 -- 73}, year = {2000}, language = {de} } @article{MertensHenke2001, author = {Mertens, Josef and Henke, Rolf}, title = {Adaptive technologies for future civil air transport}, series = {Air \& Space Europe. 3 (2001), H. 3-4}, journal = {Air \& Space Europe. 3 (2001), H. 3-4}, isbn = {1247-5793}, pages = {80 -- 82}, year = {2001}, language = {en} } @article{Mertens2006, author = {Mertens, Josef}, title = {Luft hat keine Balken, aber enorme Kr{\"a}fte : Aerodynamik - die unsichtbare Kraft}, series = {HEmagazin : das Hocheffizienz-Magazin von Wilo. 2006 (2006), H. 1}, journal = {HEmagazin : das Hocheffizienz-Magazin von Wilo. 2006 (2006), H. 1}, publisher = {-}, pages = {4 -- 9}, year = {2006}, language = {de} } @article{Mertens1998, author = {Mertens, Josef}, title = {Required technologies for supersonic aircraft}, series = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamic research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, journal = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamic research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, publisher = {Research and Technology Organization}, address = {Neuilly-sur-Seine}, isbn = {92-837-1007-X}, pages = {5.1 -- 5.16}, year = {1998}, language = {en} } @article{Mertens1998, author = {Mertens, Josef}, title = {Multi point design challenges for supersonic transports}, series = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamics research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, journal = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamics research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, publisher = {Research and Technology Organization}, address = {Neuilly-sur-Seine}, isbn = {92-837-1007-X}, pages = {8.1 -- 8.12}, year = {1998}, language = {en} } @article{OverduinBlomeHoell2007, author = {Overduin, James and Blome, Hans-Joachim and Hoell, Josef}, title = {Wolfgang Priester: from the big bounce to the Lambda-dominated universe}, series = {Naturwissenschaften}, volume = {94}, journal = {Naturwissenschaften}, number = {6}, isbn = {0028-1042}, pages = {417 -- 429}, year = {2007}, language = {en} } @article{TrillaGrossenRobinsonetal.2008, author = {Trilla, Joan and Grossen, J{\"u}rgen and Robinson, Alexander and Funke, Harald and Bosschaerts, Walter and Hendrick, Patrick}, title = {Development of a hydrogen combustion chamber for an ultra micro gas turbine}, series = {PowerMEMS 2008, 8th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications, microEMS 2008, 2nd Symposium on Micro Environmental Machine Systems, Sendai, JP, Nov 9-12, 2008}, journal = {PowerMEMS 2008, 8th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications, microEMS 2008, 2nd Symposium on Micro Environmental Machine Systems, Sendai, JP, Nov 9-12, 2008}, pages = {101 -- 104}, year = {2008}, language = {en} } @article{RobinsonFunkeHendricketal.2008, author = {Robinson, A. E. and Funke, Harald and Hendrick, P. and Recker, E. and Peirs, J.}, title = {Development of a hydrogen fuelled 1 kW ultra micro gas turbine with special respect to designing, testing and mapping of the µ-scale combustor}, series = {IEEE International Conference on Sustainable Energy Technologies, 2008 : ICSET 2008 ; Singapore, 24 - 27 Nov. 2008.}, journal = {IEEE International Conference on Sustainable Energy Technologies, 2008 : ICSET 2008 ; Singapore, 24 - 27 Nov. 2008.}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4244-1887-9}, pages = {656 -- 660}, year = {2008}, language = {en} } @article{BlomeChiconeHehletal.2010, author = {Blome, Hans-Joachim and Chicone, Carmen and Hehl, Friedrich W. and Mashhoon, Bahram}, title = {Nonlocal modification of Newtonian gravity}, series = {Physical Review D}, volume = {81}, journal = {Physical Review D}, number = {6}, isbn = {0556-2821}, pages = {065020}, year = {2010}, language = {en} } @article{WilsonBlome2009, author = {Wilson, T. L. and Blome, Hans-Joachim}, title = {The Pioneer anomaly and a rotating G{\"o}del universe}, series = {Advances in Space Research}, volume = {44}, journal = {Advances in Space Research}, number = {11}, isbn = {0273-1177}, pages = {1345 -- 1353}, year = {2009}, language = {en} } @article{HavermannSalveTinetal.1994, author = {Havermann, Marc and Salve, M. de and Tin, G. del and Panella, B.}, title = {Experimental Study of the Temperature Field along a Density Lock / Salve, M. de ; Tin, G. del ; Panella, B. ; Sansoldo, D. ; Havermann, M.}, series = {Proceedings : International Conference on New Trends in Nuclear System Thermohydraulics, May 30th - June 2nd, 1994, Pisa / organized by Dipartimento di Costruzioni Meccaniche e Nucleari ... . Ed. by Francesco Oriolo}, journal = {Proceedings : International Conference on New Trends in Nuclear System Thermohydraulics, May 30th - June 2nd, 1994, Pisa / organized by Dipartimento di Costruzioni Meccaniche e Nucleari ... . Ed. by Francesco Oriolo}, publisher = {-}, address = {Pisa}, pages = {623 -- 630}, year = {1994}, language = {en} } @article{HavermannBeylich1998, author = {Havermann, Marc and Beylich, A. E.}, title = {Combined Measurement of Velocity, Temperature and Pressure in Compressible Gas Flows Using Laser-Induced Iodine Fluorescence / Havermann, M. ; Beylich, A. E.}, publisher = {-}, year = {1998}, language = {en} } @article{HavermannSeilerGeorgeetal.2002, author = {Havermann, Marc and Seiler, F. and George, A. and Leopold, F.}, title = {Enhanced Doppler Picture Velocimetry (DPV) for Planar Velocity Measurements in High-Speed Shock Tunnel Flow / Seiler, F. ; George, A. ; Leopold, F. ; Havermann, M. ; Srulijes, J.}, series = {10th International Symposium on Flow Visualization : Kyōto, Japan, August 26 - 29, 2002 / sponsored by International Flow Visualization Society . [Chairman:] Toshio Kobayashi}, journal = {10th International Symposium on Flow Visualization : Kyōto, Japan, August 26 - 29, 2002 / sponsored by International Flow Visualization Society . [Chairman:] Toshio Kobayashi}, publisher = {Visualization Society of Japan}, address = {Kyoto}, isbn = {4906497829}, year = {2002}, language = {en} } @article{LeyPlescherScholzetal.2007, author = {Ley, Wilfried and Plescher, Engelbert and Scholz, Artur and Piepenbrock, Johannes}, title = {COMPASS-1 picosatellite project / Ley, Wilfried ; Plescher, Engelbert ; Scholz, Artur ; Piepenbrock, Johannes}, series = {Small satellites for earth observation : digest of the 6th International symposium of the International Academy of Astronautics, Berlin, April 23 - 26, 2007 / ed. by Rainer Sandau; Hans-Peter R{\"o}ser; Arnoldo Valenzuela}, journal = {Small satellites for earth observation : digest of the 6th International symposium of the International Academy of Astronautics, Berlin, April 23 - 26, 2007 / ed. by Rainer Sandau; Hans-Peter R{\"o}ser; Arnoldo Valenzuela}, publisher = {Wissenschaft und Technik Verl.}, address = {Berlin}, isbn = {9783896855718}, pages = {147 -- 150}, year = {2007}, language = {en} } @article{WittmannKehrWillnecker2000, author = {Wittmann, Klaus and Kehr, J. and Willnecker, R.}, title = {Decentralized Payload Operations Concept for Columbus}, year = {2000}, language = {en} } @article{WittmannBibringRosenbaueretal.2007, author = {Wittmann, Klaus and Bibring, J.-P. and Rosenbauer, H. and Boehnhardt, H.}, title = {The Rosetta Lander ("Philae") Investigations / Bibring, J.-P. ; Rosenbauer, H. ; Boehnhardt, H. ; [...] Wittmann, K.}, series = {Space Science Reviews. 128 (2007), H. 1-4}, journal = {Space Science Reviews. 128 (2007), H. 1-4}, isbn = {0038-6308}, pages = {205 -- 220}, year = {2007}, language = {en} } @article{RoethSchreiber2003, author = {R{\"o}th, Thilo and Schreiber, Harold}, title = {CAKE (Computer Aided Kinematic Engineering) im Karrosseriebau und in der passiven Fahrzeugsicherheit / Schreiber , Harold ; R{\"o}th, Thilo}, series = {Mobiles. 2002/2003 (2003), H. 33}, journal = {Mobiles. 2002/2003 (2003), H. 33}, pages = {65 -- 67}, year = {2003}, language = {de} } @article{RoethNowackBaumeister2006, author = {R{\"o}th, Thilo and Nowack, N. and Baumeister, E.}, title = {Numerische L{\"o}sungsans{\"a}tze zur Auslegung von Stahl-Leichtmetall-Hybriden aus Verbundguss f{\"u}r zuk{\"u}nftige Fahrzeugstrukturen / Nowack, N. ; R{\"o}th, T. ; Baumeister, E.}, series = {Berechnung und Simulation im Fahrzeugbau. Bd. 1 : Tagung W{\"u}rzburg, 27. und 28. September 2006 = Numerical analysis and simulation in vehicle engineering / VDI-Gesellschaft Fahrzeug- und Verkehrstechnik}, journal = {Berechnung und Simulation im Fahrzeugbau. Bd. 1 : Tagung W{\"u}rzburg, 27. und 28. September 2006 = Numerical analysis and simulation in vehicle engineering / VDI-Gesellschaft Fahrzeug- und Verkehrstechnik}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, isbn = {3-18-091967-1}, pages = {363 -- 368}, year = {2006}, language = {de} } @article{Wittmann2000, author = {Wittmann, Klaus}, title = {Overview of Space Operations at DLR}, year = {2000}, language = {en} } @article{Mertens1998, author = {Mertens, Josef}, title = {Aerodynamische Ziele des Adaptiven Fl{\"u}gels (ADIF).}, series = {DGLR-Jahrbuch 1998 Bd. 1}, journal = {DGLR-Jahrbuch 1998 Bd. 1}, pages = {47 -- 52}, year = {1998}, language = {de} } @article{MertensHuenecke1988, author = {Mertens, Josef and H{\"u}necke, Klaus}, title = {Experimentelle Untersuchung zur Landeeigenschaft von Hyperschall-Flugger{\"a}ten / H{\"u}necke, Klaus ; Mertens, Josef}, series = {DGLR-Jahrbuch 1988 Bd. 1}, journal = {DGLR-Jahrbuch 1988 Bd. 1}, pages = {706}, year = {1988}, language = {de} } @article{MertensKelmVelden1999, author = {Mertens, Josef and Kelm, R. and Velden, A. van der}, title = {Interdisziplin{\"a}re Auslegung eines Verkehrsflugzeugfl{\"u}gels}, series = {DGLR-Jahrbuch 1999 Bd. 3}, journal = {DGLR-Jahrbuch 1999 Bd. 3}, pages = {1605 -- 1610}, year = {1999}, language = {de} } @article{Mertens1999, author = {Mertens, Josef}, title = {Einige herausragende Ergebnisse des Technologieprogramms "Reduktion des Aerodynamischen Widerstands (RaWid)"}, series = {DGLR-Jahrbuch 1999 Bd. 3}, journal = {DGLR-Jahrbuch 1999 Bd. 3}, pages = {1461 -- 1468}, year = {1999}, language = {de} } @article{Mertens1992, author = {Mertens, Josef}, title = {Laminar flow for supersonic transports}, series = {Proceedings : March 16 - 18, 1992, Congress Centrum, Hamburg, Federal Republic of Germany / organized jointly by: Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt e.V. ... [Programme committee J. Szodruch ...]}, journal = {Proceedings : March 16 - 18, 1992, Congress Centrum, Hamburg, Federal Republic of Germany / organized jointly by: Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt e.V. ... [Programme committee J. Szodruch ...]}, publisher = {DGLR}, address = {Bonn}, isbn = {3-922010-73-3}, pages = {319 -- 323}, year = {1992}, language = {en} } @article{BohnFunke2003, author = {Bohn, Dieter and Funke, Harald}, title = {Experimental investigations into the nonuniform flow in a 4-stage turbine with special focus on the flow equalization in the first turbine stage}, series = {ASME TURBO EXPO, Proceedings of the ASME Turbo Expo, 2003}, journal = {ASME TURBO EXPO, Proceedings of the ASME Turbo Expo, 2003}, isbn = {0-7918-3689-4}, pages = {281 -- 289}, year = {2003}, language = {en} } @article{Gerhardt2005, author = {Gerhardt, Hans Joachim}, title = {Design methods of smoke and heat exhaust systems in construction works}, series = {V Mie\&\#796;dzynarodowa Konferencja Bezpiecze\&\#324;stwo Po\&\#380;arowe Budowli, Warszawa-Miedzeszyn, 14 - 16 listopada 2005 r. = : Vth International Conference Fire Safety of Buildings / ITB ... [Ed. Miros\&\#322;aw Kosiorek]}, journal = {V Mie\&\#796;dzynarodowa Konferencja Bezpiecze\&\#324;stwo Po\&\#380;arowe Budowli, Warszawa-Miedzeszyn, 14 - 16 listopada 2005 r. = : Vth International Conference Fire Safety of Buildings / ITB ... [Ed. Miros\&\#322;aw Kosiorek]}, publisher = {ITB}, address = {Warszawa}, isbn = {83-7413-810-6}, pages = {127 -- 140}, year = {2005}, language = {en} } @article{GerhardtSchoenwaldForssmannetal.2005, author = {Gerhardt, Hans Joachim and Sch{\"o}nwald, J. and Forßmann, R. and Große, Wolfgang}, title = {Modulation der Windenergie durch optimierte Uferbepflanzung zur Steuerung der Oberfl{\"a}chenstr{\"o}mung f{\"u}r das Entfernung von Treibgut}, series = {Der F{\"u}hlinger See : Beitr{\"a}ge zur Erhaltung der {\"o}kologischen Qualit{\"a}t / hrsg. von Wolfgang Große ... - ({\"O}kologie und nachhaltige Entwicklung von Sport- und Freizeitseen ; 1)}, journal = {Der F{\"u}hlinger See : Beitr{\"a}ge zur Erhaltung der {\"o}kologischen Qualit{\"a}t / hrsg. von Wolfgang Große ... - ({\"O}kologie und nachhaltige Entwicklung von Sport- und Freizeitseen ; 1)}, publisher = {Monsenstein und Vannerdat}, address = {M{\"u}nster}, isbn = {3-86582-212-6}, pages = {95 -- 108}, year = {2005}, language = {de} } @article{Gerhardt2006, author = {Gerhardt, Hans Joachim}, title = {Wind- und Temperatureinfl{\"u}sse bei der Planung von Entrauchungseinrichtungen}, series = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 55 (2006), H. 3}, journal = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 55 (2006), H. 3}, isbn = {0042-1804}, pages = {115 -- 121}, year = {2006}, language = {de} } @article{GerhardtKonrathStiel2006, author = {Gerhardt, Hans Joachim and Konrath, B. and Stiel, M.}, title = {Anmerkungen zur DIN EN 12101-2 {\"u}ber die Pr{\"u}fung von nat{\"u}rlichen Rauch- und W{\"a}rmeabzugsanlagen (NRGW)}, series = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 55 (2006), H. 3}, journal = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 55 (2006), H. 3}, isbn = {0042-1804}, pages = {157 -- 158}, year = {2006}, language = {de} } @article{GerhardtSchoenwaldKonrath2007, author = {Gerhardt, Hans Joachim and Sch{\"o}nwald, J. and Konrath, B.}, title = {Verwendung von Leichtgas bei Brandsimulationen - unzul{\"a}ssig oder sinnvoll?}, series = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 56 (2007), H. 1}, journal = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 56 (2007), H. 1}, isbn = {0042-1804}, pages = {29 -- 31}, year = {2007}, language = {de} } @article{GerhardtKonrathSchoenwald2005, author = {Gerhardt, Hans Joachim and Konrath, B. and Sch{\"o}nwald, J.}, title = {Brandsimulation f{\"u}r Abnahmeversuche}, series = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik. 56 (2005), H. 8}, journal = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik. 56 (2005), H. 8}, isbn = {1436-5103}, pages = {46 -- 51}, year = {2005}, language = {de} } @article{GerhardtKonrathLieb2005, author = {Gerhardt, Hans Joachim and Konrath, B. and Lieb, R.-D.}, title = {Das Drallrohr}, series = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik. 56 (2005), H. 11}, journal = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik. 56 (2005), H. 11}, isbn = {1436-5103}, pages = {91 -- 95}, year = {2005}, language = {en} } @article{GerhardtKrueger1997, author = {Gerhardt, Hans Joachim and Kr{\"u}ger, O.}, title = {Building shape influence on local wind loads}, series = {Proceedings of the 2nd European \& African Conference on Wind Engineering : 2 EACWE, Palazzo Ducale, Genova, Italy, June 22-26, 1997 / ed. by Giovanni Solari. - Vol. 2}, journal = {Proceedings of the 2nd European \& African Conference on Wind Engineering : 2 EACWE, Palazzo Ducale, Genova, Italy, June 22-26, 1997 / ed. by Giovanni Solari. - Vol. 2}, publisher = {Servizi Grafici Editoriali}, address = {Padova}, isbn = {88-86281-19-6}, pages = {XIX, S. 1017 - 1998 : Ill., graph. Darst.}, year = {1997}, language = {en} } @article{Gerhardt2005, author = {Gerhardt, Hans Joachim}, title = {Teures Bauen durch starre Genehmigungspraxis}, series = {Der Bausachverst{\"a}ndige : Zeitschrift f{\"u}r Bausch{\"a}den, Grundst{\"u}ckswert und gutachterliche T{\"a}tigkeit. 1 (2005), H. 5}, journal = {Der Bausachverst{\"a}ndige : Zeitschrift f{\"u}r Bausch{\"a}den, Grundst{\"u}ckswert und gutachterliche T{\"a}tigkeit. 1 (2005), H. 5}, isbn = {1614-6123}, pages = {44 -- 45}, year = {2005}, language = {de} } @article{GerhardtLieb2005, author = {Gerhardt, Hans Joachim and Lieb, R.-D.}, title = {Entrauchung komplexer R{\"a}umlichkeiten : Strategien und Steuerungen}, series = {T{\"u}r-Tor-Fenster-Report : Fachzeitschrift f{\"u}r die Technologien von T{\"u}ren, Toren und Fenstern. 25 (2005), H. 3}, journal = {T{\"u}r-Tor-Fenster-Report : Fachzeitschrift f{\"u}r die Technologien von T{\"u}ren, Toren und Fenstern. 25 (2005), H. 3}, isbn = {0724-7702}, pages = {27 -- 29}, year = {2005}, language = {de} } @article{Gerhardt2005, author = {Gerhardt, Hans Joachim}, title = {Physikalische Modelle f{\"u}r Brandsicherheitsnachweise = physical models for fire safety design}, series = {Kurzreferate : Hannover, 6. und 7. Juni 2005 = Proceedings / [Veranst.: VFDB, Vereinigung zur F{\"o}rderung des Deutschen Brandschutzes e.V.; iBMB, Institut f{\"u}r Baustoffe, Massivbau und Brandschutz der Technischen Universit{\"a}t Braunschweig]. Hrsg.: Dietmar Hosser}, journal = {Kurzreferate : Hannover, 6. und 7. Juni 2005 = Proceedings / [Veranst.: VFDB, Vereinigung zur F{\"o}rderung des Deutschen Brandschutzes e.V.; iBMB, Institut f{\"u}r Baustoffe, Massivbau und Brandschutz der Technischen Universit{\"a}t Braunschweig]. Hrsg.: Dietmar Hosser}, publisher = {iBMB}, address = {Braunschweig}, isbn = {3-89288-165-0}, pages = {135 -- 154}, year = {2005}, language = {de} } @article{FunkeDickhoffKeinzetal.2014, author = {Funke, Harald and Dickhoff, J. and Keinz, Jan and Anis, H. A. and Parente, A. and Hendrick, P.}, title = {Experimental and numerical study of the micromix combustion principle applied for hydrogen and hydrogen-rich syngas as fuel with increased energy density for industrial gas turbine applications}, series = {Energy procedia}, journal = {Energy procedia}, number = {61}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102 (E-Journal)}, doi = {10.1016/j.egypro.2014.12.201}, pages = {1736 -- 1739}, year = {2014}, abstract = {The Dry Low NOx (DLN) Micromix combustion principle with increased energy density is adapted for the industrial gas turbine APU GTCP 36-300 using hydrogen and hydrogen-rich syngas with a composition of 90\%-Vol. hydrogen (H₂) and 10\%-Vol. carbon-monoxide (CO). Experimental and numerical studies of several combustor geometries for hydrogen and syngas show the successful advance of the DLN Micromix combustion from pure hydrogen to hydrogen-rich syngas. The impact of the different fuel properties on the combustion principle and aerodynamic flame stabilization design laws, flow field, flame structure and emission characteristics is investigated by numerical analysis using a hybrid Eddy Break Up combustion model and validated against experimental results.}, language = {en} } @article{SchirraWatmuffBauschat2014, author = {Schirra, Julian and Watmuff, Jonathan and Bauschat, J.-Michael}, title = {Highly non-planar lifting systems: a relative assessment of existing potential-methodologies to accurately estimate the induced drag}, series = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.}, journal = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.}, organization = {American Institute of Aeronautics and Astronautics}, isbn = {978-1-62410-288-2}, doi = {10.2514/6.2014-2988}, pages = {Publ. online}, year = {2014}, language = {en} } @article{HajAyedKustererFunkeetal.2015, author = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.}, title = {Experimental and numerical investigations of the dry-low-NOx hydrogen micromix combustion chamber of an industrial gas turbine}, series = {Propulsion and power research}, volume = {Vol. 4}, journal = {Propulsion and power research}, number = {Iss. 3}, issn = {2212-540X}, doi = {10.1016/j.jppr.2015.07.005}, pages = {123 -- 131}, year = {2015}, language = {en} } @article{HajAyedKustererFunkeetal.2015, author = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.}, title = {Improvement study for the dry-low-NOx hydrogen micromix combustion technology}, series = {Propulsion and power research}, volume = {Vol. 4}, journal = {Propulsion and power research}, number = {Iss. 3}, issn = {2212-540X}, doi = {10.1016/j.jppr.2015.07.003}, pages = {132 -- 140}, year = {2015}, language = {en} } @article{BindalSharmaJanseretal.2013, author = {Bindal, Gaurav and Sharma, Sparsh and Janser, Frank and Neu, Eugen}, title = {Detailed analysis of variables affecting wing kinematics of bat flight}, series = {SAE International Journal of Aerospace}, volume = {6}, journal = {SAE International Journal of Aerospace}, number = {2}, issn = {1946-3901}, doi = {10.4271/2013-01-9003}, pages = {811 -- 818}, year = {2013}, language = {en} } @article{SchuellerKowalskiRaback2016, author = {Sch{\"u}ller, K. and Kowalski, Julia and Raback, P.}, title = {Curvilinear melting - A preliminary experimental and numerical study}, series = {International Journal of Heat and Mass Transfer}, journal = {International Journal of Heat and Mass Transfer}, number = {92}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0017-9310}, doi = {10.1016/j.ijheatmasstransfer.2015.09.046}, pages = {884 -- 892}, year = {2016}, abstract = {When exploring glacier ice it is often necessary to take samples or implement sensors at a certain depth underneath the glacier surface. One way of doing this is by using heated melting probes. In their common form these devices experience a straight one-dimensional downwards motion and can be modeled by standard close-contact melting theory. A recently developed melting probe however, the IceMole, achieves maneuverability by simultaneously applying a surface temperature gradient to induce a change in melting direction and controlling the effective contact-force by means of an ice screw to stabilize its change in attitude. A modeling framework for forced curvilinear melting does not exist so far and will be the content of this paper. At first, we will extend the existing theory for quasi-stationary close-contact melting to curved trajectories. We do this by introducing a rotational mode. This additional unknown in the system implies yet the need for another model closure. Within this new framework we will focus on the effect of a variable contact-force as well as different surface temperature profiles. In order to solve for melting velocity and curvature of the melting path we present both an inverse solution strategy for the analytical model, and a more general finite element framework implemented into the open source software package ELMER. Model results are discussed and compared to experimental data conducted in laboratory tests.}, language = {de} } @article{StadlerGarveyEmbsetal.2014, author = {Stadler, Alexander Maximilian and Garvey, Christopher J. and Embs, Jan Peter and Koza, Michael Marek and Unruh, Tobias and Artmann, Gerhard and Zaccai, Guiseppe}, title = {Picosecond dynamics in haemoglobin from different species: A quasielastic neutron scattering study}, series = {Biochimica et biophysica acta (BBA): General Subjects}, volume = {1840}, journal = {Biochimica et biophysica acta (BBA): General Subjects}, number = {10}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-8006 (E-Journal); 0304-4165 (Print)}, doi = {10.1016/j.bbagen.2014.06.007}, pages = {2989 -- 2999}, year = {2014}, language = {en} } @article{MathiakPlescherWillnecker2005, author = {Mathiak, Gerhard and Plescher, Engelbert and Willnecker, Rainer}, title = {Liquid metal diffusion experiments in microgravity - Vibrational effects}, series = {Measurement science and technology}, volume = {Vol. 16}, journal = {Measurement science and technology}, number = {No. 2}, issn = {0957-0233}, doi = {10.1088/0957-0233/16/2/003}, pages = {336}, year = {2005}, language = {en} } @article{MathiakWillneckerPlescher2005, author = {Mathiak, Gerhard and Willnecker, Rainer and Plescher, Engelbert}, title = {Vibrational effects on diffusion experiments}, series = {Microgravity science and technology : international journal for microgravity research and applications}, volume = {Vol. 15}, journal = {Microgravity science and technology : international journal for microgravity research and applications}, number = {No. 1}, issn = {0938-0108}, pages = {295 -- 300}, year = {2005}, language = {en} } @article{HoevelerJanserBindewaldetal.2015, author = {Hoeveler, Bastian and Janser, Frank and Bindewald, Thorsten and Gebhardt, Andreas}, title = {Entwurf, Fertigung und Untersuchung eines Windkanalmodells eines innovativen, senkrechtstartenden Kleinflugzeuges}, series = {RTejournal - Forum f{\"u}r Rapid Technologie}, journal = {RTejournal - Forum f{\"u}r Rapid Technologie}, number = {12}, publisher = {Fachhochschule Aachen}, address = {Aachen}, issn = {1614-0923}, url = {http://nbn-resolving.de/urn:nbn:de:0009-2-42921}, pages = {1 -- 5}, year = {2015}, language = {de} } @article{FunkeBeckmann2022, author = {Funke, Harald and Beckmann, Nils}, title = {Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture}, series = {International Journal of Gas Turbine, Propulsion and Power Systems}, volume = {13}, journal = {International Journal of Gas Turbine, Propulsion and Power Systems}, number = {2}, issn = {1882-5079}, pages = {1 -- 7}, year = {2022}, abstract = {The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.\% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance}, language = {en} } @article{BergmannMoehrenBraunetal.2023, author = {Bergmann, Ole and M{\"o}hren, Felix and Braun, Carsten and Janser, Frank}, title = {On the influence of elasticity on swept propeller noise}, series = {AIAA SCITECH 2023 Forum}, journal = {AIAA SCITECH 2023 Forum}, publisher = {AIAA}, address = {Reston, Va.}, doi = {10.2514/6.2023-0210}, year = {2023}, abstract = {High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation.}, language = {en} } @article{PeloniDachwaldCeriotti2017, author = {Peloni, Alessandro and Dachwald, Bernd and Ceriotti, Matteo}, title = {Multiple near-earth asteroid rendezvous mission: Solar-sailing options}, series = {Advances in Space Research}, journal = {Advances in Space Research}, number = {In Press, Corrected Proof}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0273-1177}, doi = {10.1016/j.asr.2017.10.017}, year = {2017}, language = {en} } @article{DachwaldSeboldtLoebetal.2008, author = {Dachwald, Bernd and Seboldt, Wolfgang and Loeb, H. W. and Schartner, Karl-Heinz}, title = {Main Belt Asteroid Sample Return Mission Using Solar Electric Propulsion}, series = {Acta Astronautica. 63 (2008), H. 1-4}, journal = {Acta Astronautica. 63 (2008), H. 1-4}, isbn = {0094-5765}, pages = {91 -- 101}, year = {2008}, language = {en} } @article{KezerashviliDachwald2021, author = {Kezerashvili, Roman Ya and Dachwald, Bernd}, title = {Preface: Solar sailing: Concepts, technology, and missions II}, series = {Advances in Space Research}, volume = {67}, journal = {Advances in Space Research}, number = {9}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0273-1177}, doi = {10.1016/j.asr.2021.01.037}, pages = {2559 -- 2560}, year = {2021}, language = {en} } @article{DachwaldOhndorfSeboldt2005, author = {Dachwald, Bernd and Ohndorf, A. and Seboldt, Wolfgang}, title = {Optimierung der Lageregelung von Raumfahrzeugen mit Niedrigschubantrieb mittels evolution{\"a}rer neuronaler Regler / A. Ohndorf ; B. Dachwald ; W. Seboldt}, series = {Deutscher Luft- und Raumfahrtkongress 2005 : Friedrichshafen, 26. bis 29. September 2005, Motto: Luft- und Raumfahrt - Grenzen {\"u}berwinden, Horizonte erweitern / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V. (DGLR). [Red.: Peter Brandt (verantwortlich)]. Bd. 3. - (Jahrbuch ... der Deutschen Gesellschaft f{\"u}r Luft- und Raumfahrt}, journal = {Deutscher Luft- und Raumfahrtkongress 2005 : Friedrichshafen, 26. bis 29. September 2005, Motto: Luft- und Raumfahrt - Grenzen {\"u}berwinden, Horizonte erweitern / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V. (DGLR). [Red.: Peter Brandt (verantwortlich)]. Bd. 3. - (Jahrbuch ... der Deutschen Gesellschaft f{\"u}r Luft- und Raumfahrt}, publisher = {DGLR}, address = {Bonn}, pages = {1971 -- 1978}, year = {2005}, language = {de} } @article{SpietzSproewitzSeefeldtetal.2021, author = {Spietz, Peter and Spr{\"o}witz, Tom and Seefeldt, Patric and Grundmann, Jan Thimo and Jahnke, Rico and Mikschl, Tobias and Mikulz, Eugen and Montenegro, Sergio and Reershemius, Siebo and Renger, Thomas and Ruffer, Michael and Sasaki, Kaname and Sznajder, Maciej and T{\´o}th, Norbert and Ceriotti, Matteo and Dachwald, Bernd and Macdonald, Malcolm and McInnes, Colin and Seboldt, Wolfgang and Quantius, Dominik and Bauer, Waldemar and Wiedemann, Carsten and Grimm, Christian D. and Hercik, David and Ho, Tra-Mi and Lange, Caroline and Schmitz, Nicole}, title = {Paths not taken - The Gossamer roadmap's other options}, series = {Advances in Space Research}, volume = {67}, journal = {Advances in Space Research}, number = {9}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0273-1177}, doi = {10.1016/j.asr.2021.01.044}, pages = {2912 -- 2956}, year = {2021}, language = {en} } @article{DachwaldBaturkinCoverstoneetal.2006, author = {Dachwald, Bernd and Baturkin, Volodymyr and Coverstone, Victoria L. and Dietrich, Benjamin and Garbe, Gregory P. and G{\"o}rlich, Marianne and Leipold, Manfred and Lura, Franz and Macdonald, Malcolm and McInnes, Colin R. and Mengali, Giovanni and Quatra, Alessandro A. and Rios-Reyes, Leonel and Scheeres, Daniel J. and Seboldt, Wolfgang and Wie, Bong}, title = {Potential Effects of Optical Solar Sail Degradation on Interplanetary Trajectory Design}, series = {Astrodynamics 2005 : proceedings of the AAS/AIAA astrodynamics conference held August 7 - 11, 2005, South Lake Tahoe, California / ed. by Bobby G. Williams. - Pt. 3. - (Advances in the astronautical sciences ; 123,3)}, journal = {Astrodynamics 2005 : proceedings of the AAS/AIAA astrodynamics conference held August 7 - 11, 2005, South Lake Tahoe, California / ed. by Bobby G. Williams. - Pt. 3. - (Advances in the astronautical sciences ; 123,3)}, publisher = {Univelt}, address = {San Diego, Calif.}, isbn = {0-87703-527-X}, pages = {2569 -- 2592}, year = {2006}, language = {en} } @article{DachwaldSeboldtRichter2006, author = {Dachwald, Bernd and Seboldt, Wolfgang and Richter, L.}, title = {Multiple rendezvous and sample return missions to near-Earth objects using solar sailcraft / Dachwald, B. ; Seboldt, W. ; Richter, L.}, series = {Acta Astronautica. 59 (2006), H. 8-11}, journal = {Acta Astronautica. 59 (2006), H. 8-11}, isbn = {0094-5765}, pages = {768 -- 776}, year = {2006}, language = {en} } @article{DahmannHagemeisterNageletal.2006, author = {Dahmann, Peter and Hagemeister, Wilhelm and Nagel, G{\"u}nther and Exner, Peter}, title = {Geregelte Innenzahnradpumpe im Mehrquadrantenbetrieb Geschwindigkeits- und Positionsregelung eines hydraulischen Handlingger{\"a}tes}, series = {O+P {\"O}lhydraulik und Pneumatik. 24 (2006), H. 1}, journal = {O+P {\"O}lhydraulik und Pneumatik. 24 (2006), H. 1}, isbn = {0341-2660}, pages = {24 -- 28}, year = {2006}, language = {de} } @article{Dachwald2004, author = {Dachwald, Bernd}, title = {Evolutionary Neurocontrol: A Smart Method for Global Optimization of Low-Thrust Trajectories}, series = {22nd AIAA Applied Aerodynamics Conference and Exhibit - AIAA/AAS Astrodynamics Specialist Conference and Exhibit - AIAA Guidance, Navigation, and Control Conference and Exhibit - AIAA Modeling and Simulation Technologies Conference and Exhibit - AIAA Atmospheric Flight Mechanics Conference and Exhibit : 16 - 19 August 2004, Providence, Rhode Island / American Institute of Aeronautics and Astronautics. - (AIAA meeting papers on disc ; 2004,14-15)}, journal = {22nd AIAA Applied Aerodynamics Conference and Exhibit - AIAA/AAS Astrodynamics Specialist Conference and Exhibit - AIAA Guidance, Navigation, and Control Conference and Exhibit - AIAA Modeling and Simulation Technologies Conference and Exhibit - AIAA Atmospheric Flight Mechanics Conference and Exhibit : 16 - 19 August 2004, Providence, Rhode Island / American Institute of Aeronautics and Astronautics. - (AIAA meeting papers on disc ; 2004,14-15)}, publisher = {American Inst. of Aeronautics and Astronautics}, address = {Reston, Va.}, pages = {2 CD-ROMs}, year = {2004}, language = {en} } @article{HeiligersSchoutetensDachwald2021, author = {Heiligers, Jeannette and Schoutetens, Frederic and Dachwald, Bernd}, title = {Photon-sail equilibria in the alpha centauri system}, series = {Journal of Guidance, Control, and Dynamics}, volume = {44}, journal = {Journal of Guidance, Control, and Dynamics}, number = {5}, issn = {1533-3884}, doi = {10.2514/1.G005446}, pages = {1053 -- 1061}, year = {2021}, language = {en} } @article{MoehrenBergmannJanseretal.2024, author = {M{\"o}hren, Felix and Bergmann, Ole and Janser, Frank and Braun, Carsten}, title = {Assessment of structural mechanical effects related to torsional deformations of propellers}, series = {CEAS Aeronautical Journal}, journal = {CEAS Aeronautical Journal}, publisher = {Springer}, address = {Wien}, issn = {1869-5590 (eISSN)}, doi = {10.1007/s13272-024-00737-7}, pages = {22 Seiten}, year = {2024}, abstract = {Lifting propellers are of increasing interest for Advanced Air Mobility. All propellers and rotors are initially twisted beams, showing significant extension-twist coupling and centrifugal twisting. Torsional deformations severely impact aerodynamic performance. This paper presents a novel approach to assess different reasons for torsional deformations. A reduced-order model runs large parameter sweeps with algebraic formulations and numerical solution procedures. Generic beams represent three different propeller types for General Aviation, Commercial Aviation, and Advanced Air Mobility. Simulations include solid and hollow cross-sections made of aluminum, steel, and carbon fiber-reinforced polymer. The investigation shows that centrifugal twisting moments depend on both the elastic and initial twist. The determination of the centrifugal twisting moment solely based on the initial twist suffers from errors exceeding 5\% in some cases. The nonlinear parts of the torsional rigidity do not significantly impact the overall torsional rigidity for the investigated propeller types. The extension-twist coupling related to the initial and elastic twist in combination with tension forces significantly impacts the net cross-sectional torsional loads. While the increase in torsional stiffness due to initial twist contributes to the overall stiffness for General and Commercial Aviation propellers, its contribution to the lift propeller's stiffness is limited. The paper closes with the presentation of approximations for each effect identified as significant. Numerical evaluations are necessary to determine each effect for inhomogeneous cross-sections made of anisotropic material.}, language = {en} } @article{NeuJanserKhatibietal.2016, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Braun, Carsten and Orifici, Adrian C.}, title = {Operational Modal Analysis of a wing excited by transonic flow}, series = {Aerospace Science and Technology}, volume = {49}, journal = {Aerospace Science and Technology}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1270-9638}, doi = {10.1016/j.ast.2015.11.032}, pages = {73 -- 79}, year = {2016}, abstract = {Operational Modal Analysis (OMA) is a promising candidate for flutter testing and Structural Health Monitoring (SHM) of aircraft wings that are passively excited by wind loads. However, no studies have been published where OMA is tested in transonic flows, which is the dominant condition for large civil aircraft and is characterized by complex and unique aerodynamic phenomena. We use data from the HIRENASD large-scale wind tunnel experiment to automatically extract modal parameters from an ambiently excited wing operated in the transonic regime using two OMA methods: Stochastic Subspace Identification (SSI) and Frequency Domain Decomposition (FDD). The system response is evaluated based on accelerometer measurements. The excitation is investigated from surface pressure measurements. The forcing function is shown to be non-white, non-stationary and contaminated by narrow-banded transonic disturbances. All these properties violate fundamental OMA assumptions about the forcing function. Despite this, all physical modes in the investigated frequency range were successfully identified, and in addition transonic pressure waves were identified as physical modes as well. The SSI method showed superior identification capabilities for the investigated case. The investigation shows that complex transonic flows can interfere with OMA. This can make existing approaches for modal tracking unsuitable for their application to aircraft wings operated in the transonic flight regime. Approaches to separate the true physical modes from the transonic disturbances are discussed.}, language = {en} } @article{GoettenHavermannBraunetal.2020, author = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees}, title = {Airfoil drag at low-to-medium reynolds numbers: A novel estimation method}, series = {AIAA Journal}, volume = {58}, journal = {AIAA Journal}, number = {7}, publisher = {AIAA}, address = {Reston, Va.}, issn = {1533-385X}, doi = {10.2514/1.J058983}, pages = {2791 -- 2805}, year = {2020}, abstract = {This paper presents a novel method for airfoil drag estimation at Reynolds numbers between 4×10⁵ and 4×10⁶. The novel method is based on a systematic study of 40 airfoils applying over 600 numerical simulations and considering natural transition. The influence of the airfoil thickness-to-chord ratio, camber, and freestream Reynolds number on both friction and pressure drag is analyzed in detail. Natural transition significantly affects drag characteristics and leads to distinct drag minima for different Reynolds numbers and thickness-to-chord ratios. The results of the systematic study are used to develop empirical correlations that can accurately predict an airfoil drag at low-lift conditions. The new approach estimates a transition location based on airfoil thickness-to-chord ratio, camber, and Reynolds number. It uses the transition location in a mixed laminar-turbulent skin-friction calculation, and corrects the skin-friction coefficient for separation effects. Pressure drag is estimated separately based on correlations of thickness-to-chord ratio, camber, and Reynolds number. The novel method shows excellent accuracy when compared with wind-tunnel measurements of multiple airfoils. It is easily integrable into existing aircraft design environments and is highly beneficial in the conceptual design stage.}, language = {en} } @article{ThomaThomessenGardietal.2023, author = {Thoma, Andreas and Thomessen, Karolin and Gardi, Alessandro and Fisher, A. and Braun, Carsten}, title = {Prioritising paths: An improved cost function for local path planning for UAV in medical applications}, series = {The Aeronautical Journal}, journal = {The Aeronautical Journal}, number = {First View}, publisher = {Cambridge University Press}, address = {Cambridge}, issn = {0001-9240 (Print)}, doi = {10.1017/aer.2023.68}, pages = {1 -- 18}, year = {2023}, abstract = {Even the shortest flight through unknown, cluttered environments requires reliable local path planning algorithms to avoid unforeseen obstacles. The algorithm must evaluate alternative flight paths and identify the best path if an obstacle blocks its way. Commonly, weighted sums are used here. This work shows that weighted Chebyshev distances and factorial achievement scalarising functions are suitable alternatives to weighted sums if combined with the 3DVFH* local path planning algorithm. Both methods considerably reduce the failure probability of simulated flights in various environments. The standard 3DVFH* uses a weighted sum and has a failure probability of 50\% in the test environments. A factorial achievement scalarising function, which minimises the worst combination of two out of four objective functions, reaches a failure probability of 26\%; A weighted Chebyshev distance, which optimises the worst objective, has a failure probability of 30\%. These results show promise for further enhancements and to support broader applicability.}, language = {en} } @article{KochBoehnischVerdoncketal.2024, author = {Koch, Christopher and B{\"o}hnisch, Nils and Verdonck, Hendrik and Hach, Oliver and Braun, Carsten}, title = {Comparison of unsteady low- and mid-fidelity propeller aerodynamic methods for whirl flutter applications}, series = {Applied Sciences}, volume = {14}, journal = {Applied Sciences}, number = {2}, publisher = {MDPI}, address = {Basel}, issn = {2076-3417}, doi = {10.3390/app14020850}, pages = {1 -- 28}, year = {2024}, abstract = {Aircraft configurations with propellers have been drawing more attention in recent times, partly due to new propulsion concepts based on hydrogen fuel cells and electric motors. These configurations are prone to whirl flutter, which is an aeroelastic instability affecting airframes with elastically supported propellers. It commonly needs to be mitigated already during the design phase of such configurations, requiring, among other things, unsteady aerodynamic transfer functions for the propeller. However, no comprehensive assessment of unsteady propeller aerodynamics for aeroelastic analysis is available in the literature. This paper provides a detailed comparison of nine different low- to mid-fidelity aerodynamic methods, demonstrating their impact on linear, unsteady aerodynamics, as well as whirl flutter stability prediction. Quasi-steady and unsteady methods for blade lift with or without coupling to blade element momentum theory are evaluated and compared to mid-fidelity potential flow solvers (UPM and DUST) and classical, derivative-based methods. Time-domain identification of frequency-domain transfer functions for the unsteady propeller hub loads is used to compare the different methods. Predictions of the minimum required pylon stiffness for stability show good agreement among the mid-fidelity methods. The differences in the stability predictions for the low-fidelity methods are higher. Most methods studied yield a more unstable system than classical, derivative-based whirl flutter analysis, indicating that the use of more sophisticated aerodynamic modeling techniques might be required for accurate whirl flutter prediction.}, language = {en} } @article{GrundmannDachwaldGrimmetal.2015, author = {Grundmann, Jan Thimo and Dachwald, Bernd and Grimm, Christian D. and Kahle, Ralph and Koch, Aaron Dexter and Krause, Christian and Lange, Caroline and Quantius, Dominik and Ulamec, Stephan}, title = {Spacecraft for Hypervelocity Impact Research - An Overview of Capabilities, Constraints and the Challenges of Getting There}, series = {Procedia Engineering}, volume = {Vol. 103}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2015.04.021}, pages = {151 -- 158}, year = {2015}, language = {en} } @article{DachwaldMengaliQuartaetal.2007, author = {Dachwald, Bernd and Mengali, Giovanni and Quarta, Alessandro A. and Circi, Christian}, title = {Refined Solar Sail Force Model with Mission Application / Giovanni Mengali ; Alessandro A. Quarta , Christian Circi ; Bernd Dachwald}, series = {Journal of Guidance, Control, and Dynamics. 30 (2007), H. 2}, journal = {Journal of Guidance, Control, and Dynamics. 30 (2007), H. 2}, isbn = {0162-3192}, pages = {512 -- 520}, year = {2007}, language = {en} } @article{DachwaldOhndorfWie2006, author = {Dachwald, Bernd and Ohndorf, A. and Wie, Bong}, title = {Solar Sail Trajectory Optimization for the Solar Polar Imager (SPI) Mission}, series = {AIAA Guidance, Navigation, and Control Conference \& Exhibit - AIAA Atmospheric Flight Mechanics Conference \& Exhibit - AIAA Modeling and Simulation Technologies Conference \& Exhibit - AIAA/AAS Astrodynamics Specialist Conference \& Exhibit : [21 - 24 August 2006, Keystone, Colorado ; papers]. - (AIAA meeting papers on disc ; [11.]2006,19-20 )}, journal = {AIAA Guidance, Navigation, and Control Conference \& Exhibit - AIAA Atmospheric Flight Mechanics Conference \& Exhibit - AIAA Modeling and Simulation Technologies Conference \& Exhibit - AIAA/AAS Astrodynamics Specialist Conference \& Exhibit : [21 - 24 August 2006, Keystone, Colorado ; papers]. - (AIAA meeting papers on disc ; [11.]2006,19-20 )}, publisher = {American Institute of Aeronautics and Astronautics}, address = {Reston, Va.}, isbn = {1-56347-802-1}, pages = {2 CD-ROMs.}, year = {2006}, language = {en} } @article{DachwaldSchmidtSeboldtetal.2003, author = {Dachwald, Bernd and Schmidt, Tanja D. and Seboldt, Wolfgang and Auweter-Kurtz,}, title = {Flight Opportunities from Mars to Earth for Piloted Missions Using Continuous Thrust Propulsion / Schmidt, Tanja D. ; Dachwald, Bernd ; Seboldt, Wolfgang ; Auweter-Kurtz, Monika}, publisher = {-}, pages = {1 -- 9}, year = {2003}, language = {en} } @article{HeinEubanksHibberdetal.2020, author = {Hein, Andreas M. and Eubanks, T. Marshall and Hibberd, Adam and Fries, Dan and Schneider, Jean and Lingam, Manasvi and Kennedy, Robert and Perakis, Nikolaos and Dachwald, Bernd and Kervella, Pierre}, title = {Interstellar Now! Missions to and sample returns from nearby interstellar objects}, publisher = {Elsevier}, address = {Amsterdam}, pages = {1 -- 8}, year = {2020}, abstract = {The recently discovered first high velocity hyperbolic objects passing through the Solar System, 1I/'Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Interstellar objects likely formed very far from the solar system in both time and space; their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system.}, language = {en} } @article{CampenKowalskiLyonsetal.2019, author = {Campen, R. and Kowalski, Julia and Lyons, W.B. and Tulaczyk, S. and Dachwald, Bernd and Pettit, E. and Welch, K. A. and Mikucki, J.A.}, title = {Microbial diversity of an Antarctic subglacial community and high-resolution replicate sampling inform hydrological connectivity in a polar desert}, series = {Environmental Microbiology}, journal = {Environmental Microbiology}, number = {accepted article}, publisher = {Wiley}, address = {Weinheim}, issn = {1462-2920}, doi = {10.1111/1462-2920.14607}, year = {2019}, language = {en} } @article{DachwaldSeboldt2005, author = {Dachwald, Bernd and Seboldt, Wolfgang}, title = {Multiple Near-Earth Asteroid Rendezvous and Sample Return Using First Generation Solar Sailcraft}, series = {Acta Astronautica. 57 (2005), H. 11}, journal = {Acta Astronautica. 57 (2005), H. 11}, isbn = {0094-5765}, pages = {864 -- 875}, year = {2005}, language = {en} } @article{SchaelAtanasyanBerdugoetal.2019, author = {Schael, S. and Atanasyan, A. and Berdugo, J. and Bretz, T. and Czupalla, Markus and Dachwald, Bernd and Doetinchem, P. von and Duranti, M. and Gast, H. and Karpinski, W. and Kirn, T. and L{\"u}belsmeyer, K. and Ma{\~n}a, C. and Marrocchesi, P.S. and Mertsch, P. and Moskalenko, I.V. and Schervan, T. and Schluse, M. and Schr{\"o}der, K.-U. and Schultz von Dratzig, A. and Senatore, C. and Spies, L. and Wakely, S.P. and Wlochal, M. and Uglietti, D. and Zimmermann, J.}, title = {AMS-100: The next generation magnetic spectrometer in space - An international science platform for physics and astrophysics at Lagrange point 2}, series = {Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment}, volume = {944}, journal = {Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment}, number = {162561}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0168-9002}, doi = {10.1016/j.nima.2019.162561}, year = {2019}, language = {en} } @article{DachwaldSeboldt2003, author = {Dachwald, Bernd and Seboldt, Wolfgang}, title = {Solar sailcraft of the first generation mission applications to near-earth asteroids}, year = {2003}, language = {en} } @article{KowalskiLinderZierkeetal.2016, author = {Kowalski, Julia and Linder, Peter and Zierke, S. and Wulfen, B. van and Clemens, J. and Konstantinidis, K. and Ameres, G. and Hoffmann, R. and Mikucki, J. and Tulaczyk, S. and Funke, O. and Blandfort, D. and Espe, Clemens and Feldmann, Marco and Francke, Gero and Hiecker, S. and Plescher, Engelbert and Sch{\"o}ngarth, Sarah and Dachwald, Bernd and Digel, Ilya and Artmann, Gerhard and Eliseev, D. and Heinen, D. and Scholz, F. and Wiebusch, C. and Macht, S. and Bestmann, U. and Reineking, T. and Zetzsche, C. and Schill, K. and F{\"o}rstner, R. and Niedermeier, H. and Szumski, A. and Eissfeller, B. and Naumann, U. and Helbing, K.}, title = {Navigation technology for exploration of glacier ice with maneuverable melting probes}, series = {Cold Regions Science and Technology}, journal = {Cold Regions Science and Technology}, number = {123}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0165-232X}, doi = {10.1016/j.coldregions.2015.11.006}, pages = {53 -- 70}, year = {2016}, abstract = {The Saturnian moon Enceladus with its extensive water bodies underneath a thick ice sheet cover is a potential candidate for extraterrestrial life. Direct exploration of such extraterrestrial aquatic ecosystems requires advanced access and sampling technologies with a high level of autonomy. A new technological approach has been developed as part of the collaborative research project Enceladus Explorer (EnEx). The concept is based upon a minimally invasive melting probe called the IceMole. The force-regulated, heater-controlled IceMole is able to travel along a curved trajectory as well as upwards. Hence, it allows maneuvers which may be necessary for obstacle avoidance or target selection. Maneuverability, however, necessitates a sophisticated on-board navigation system capable of autonomous operations. The development of such a navigational system has been the focal part of the EnEx project. The original IceMole has been further developed to include relative positioning based on in-ice attitude determination, acoustic positioning, ultrasonic obstacle and target detection integrated through a high-level sensor fusion. This paper describes the EnEx technology and discusses implications for an actual extraterrestrial mission concept.}, language = {en} } @article{GoettenHavermannBraunetal.2021, author = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees}, title = {Aerodynamic Investigations of UAV Sensor Turrets - A Combined Wind-tunnel and CFD Approach}, series = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021}, journal = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021}, publisher = {AIAA}, address = {Reston, Va.}, doi = {10.2514/6.2021-1535}, pages = {1 -- 12}, year = {2021}, language = {en} } @article{Dachwald2005, author = {Dachwald, Bernd}, title = {Optimization of very-low-thrust trajectories using evolutionary neurocontrol}, series = {Acta Astronautica}, volume = {57}, journal = {Acta Astronautica}, number = {2-8}, publisher = {Elsevier}, address = {Amsterdam [u.a.]}, isbn = {1879-2030}, pages = {175 -- 185}, year = {2005}, abstract = {Searching optimal interplanetary trajectories for low-thrust spacecraft is usually a difficult and time-consuming task that involves much experience and expert knowledge in astrodynamics and optimal control theory. This is because the convergence behavior of traditional local optimizers, which are based on numerical optimal control methods, depends on an adequate initial guess, which is often hard to find, especially for very-low-thrust trajectories that necessitate many revolutions around the sun. The obtained solutions are typically close to the initial guess that is rarely close to the (unknown) global optimum. Within this paper, trajectory optimization problems are attacked from the perspective of artificial intelligence and machine learning. Inspired by natural archetypes, a smart global method for low-thrust trajectory optimization is proposed that fuses artificial neural networks and evolutionary algorithms into so-called evolutionary neurocontrollers. This novel method runs without an initial guess and does not require the attendance of an expert in astrodynamics and optimal control theory. This paper details how evolutionary neurocontrol works and how it could be implemented. The performance of the method is assessed for three different interplanetary missions with a thrust to mass ratio <0.15mN/kg (solar sail and nuclear electric).}, language = {en} } @article{GoettenFingerHavermannetal.2021, author = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.}, title = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization}, series = {CEAS Aeronautical Journal}, volume = {12}, journal = {CEAS Aeronautical Journal}, publisher = {Springer}, address = {Berlin}, issn = {1869-5590 (Online)}, doi = {10.1007/s13272-021-00522-w}, pages = {589 -- 603}, year = {2021}, abstract = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.}, language = {en} } @article{FingerBilBraun2019, author = {Finger, Felix and Bil, Cees and Braun, Carsten}, title = {Initial Sizing Methodology for Hybrid-Electric General Aviation Aircraft}, series = {Journal of Aircraft}, volume = {57}, journal = {Journal of Aircraft}, number = {2}, issn = {1533-3868}, doi = {10.2514/1.C035428}, pages = {245 -- 255}, year = {2019}, language = {en} } @article{FunkeBeckmannKeinzetal.2019, author = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester}, title = {Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications}, series = {Journal of Thermal Science and Engineering Applications}, volume = {11}, journal = {Journal of Thermal Science and Engineering Applications}, number = {1}, publisher = {ASME}, address = {New York}, issn = {19485085}, doi = {10.1115/1.4041495}, pages = {011015}, year = {2019}, language = {en} } @article{DachwaldCarnelliVasile2007, author = {Dachwald, Bernd and Carnelli, I. and Vasile, M.}, title = {Optimizing low-thrust gravity assist interplanetary trajectories using evolutionary neurocontrollers / I. Carnelli ; B. Dachwald ; M. Vasile}, series = {IEEE Congress on Evolutionary Computation, 2007 : CEC 2007 ; 25 - 28 September 2007, Singapore}, journal = {IEEE Congress on Evolutionary Computation, 2007 : CEC 2007 ; 25 - 28 September 2007, Singapore}, publisher = {IEEE Service Center}, address = {Piscataway, NJ}, isbn = {978-1-424-41339-3}, pages = {965 -- 972}, year = {2007}, language = {en} } @article{Dachwald1996, author = {Dachwald, Bernd}, title = {Entwicklung sicherer und wartbarer Software f{\"u}r den Eurofighter}, series = {Soldat und Technik : Strategie und Technik, Sicherheit (1996)}, journal = {Soldat und Technik : Strategie und Technik, Sicherheit (1996)}, isbn = {0038-0989}, pages = {663 -- 668}, year = {1996}, language = {de} } @article{DachwaldMikuckiTulaczyketal.2014, author = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng}, title = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems}, series = {Annals of Glaciology}, volume = {55}, journal = {Annals of Glaciology}, number = {65}, publisher = {Cambridge University Press}, address = {Cambridge}, issn = {1727-5644}, doi = {10.3189/2014AoG65A004}, pages = {14 -- 22}, year = {2014}, abstract = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.}, language = {en} } @article{DachwaldMcDonaldMcInnesetal.2007, author = {Dachwald, Bernd and McDonald, Malcolm and McInnes, Colin R. and Mengali, Giovanni}, title = {Impact of Optical Degradation on Solar Sail Mission Performance}, series = {Journal of Spacecraft and Rockets. 44 (2007), H. 4}, journal = {Journal of Spacecraft and Rockets. 44 (2007), H. 4}, isbn = {0022-4650}, pages = {740 -- 749}, year = {2007}, language = {en} } @article{KonstantinidisFloresMartinezDachwaldetal.2015, author = {Konstantinidis, Konstantinos and Flores Martinez, Claudio and Dachwald, Bernd and Ohndorf, Andreas and Dykta, Paul and Bowitz, Pascal and Rudolph, Martin and Digel, Ilya and Kowalski, Julia and Voigt, Konstantin and F{\"o}rstner, Roger}, title = {A lander mission to probe subglacial water on Saturn's moon enceladus for life}, series = {Acta astronautica}, volume = {Vol. 106}, journal = {Acta astronautica}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1879-2030 (E-Journal); 0094-5765 (Print)}, pages = {63 -- 89}, year = {2015}, language = {en} } @article{DachwaldUlamecPostbergetal.2020, author = {Dachwald, Bernd and Ulamec, Stephan and Postberg, Frank and Sohl, Frank and Vera, Jean-Pierre de and Christoph, Waldmann and Lorenz, Ralph D. and Hellard, Hugo and Biele, Jens and Rettberg, Petra}, title = {Key technologies and instrumentation for subsurface exploration of ocean worlds}, series = {Space Science Reviews}, volume = {216}, journal = {Space Science Reviews}, number = {Art. 83}, publisher = {Springer}, address = {Dordrecht}, issn = {1572-9672}, doi = {10.1007/s11214-020-00707-5}, pages = {45}, year = {2020}, abstract = {In this chapter, the key technologies and the instrumentation required for the subsurface exploration of ocean worlds are discussed. The focus is laid on Jupiter's moon Europa and Saturn's moon Enceladus because they have the highest potential for such missions in the near future. The exploration of their oceans requires landing on the surface, penetrating the thick ice shell with an ice-penetrating probe, and probably diving with an underwater vehicle through dozens of kilometers of water to the ocean floor, to have the chance to find life, if it exists. Technologically, such missions are extremely challenging. The required key technologies include power generation, communications, pressure resistance, radiation hardness, corrosion protection, navigation, miniaturization, autonomy, and sterilization and cleaning. Simpler mission concepts involve impactors and penetrators or - in the case of Enceladus - plume-fly-through missions.}, language = {en} } @article{GoettenFinger2020, author = {G{\"o}tten, Falk and Finger, Felix}, title = {PhoenAIX - Die modulare Transportdrohne}, series = {Ingenieurspiegel}, volume = {2020}, journal = {Ingenieurspiegel}, number = {1}, publisher = {Public Verlag}, address = {Bingen}, isbn = {1868-5919}, pages = {38 -- 40}, year = {2020}, abstract = {Die autonome, unbemannte Luftfahrt ist einer der Schl{\"u}sselsektoren f{\"u}r die Zukunft der Luftfahrt. In diesem rasant wachsenden Bereich nehmen senkrecht startende und senkrecht landende Flugzeuge (Vertical Take-Off and Landing - VTOL) einen besonderen Platz ein. Ein VTOL-Flugzeug (manchmal auch „Transitionsflugger{\"a}t" genannt) verbindet die Eigenschaft des Helikopters, {\"u}berall starten und landen zu k{\"o}nnen, mit den Geschwindigkeits-, Reichweiten und Flugdauervorteilen des Starrfl{\"u}glers. Grunds{\"a}tzlich wird die Senkrechtstart- und -landef{\"a}higkeit sowohl von zivilen als auch von milit{\"a}rischen Betreibern unbemannter Flugger{\"a}te (UAVs) gew{\"u}nscht. Trotzdem bietet der Markt nur eine geringe Anzahl von VTOL-UAVs, da qualitativ hochwertige Entw{\"u}rfe eine ausgesprochene Herausforderung in der Entwicklung darstellen. An der FH Aachen wird deshalb seit {\"u}ber 5 Jahren an der Auslegung und Analyse von solchen unbemannten VTOL Flugzeugen geforscht. Das neuste Projekt ist der Eigenentwurf einer großen, senkrechtstartenden Transportdrohne. Das „PhoenAIX" getaufte Flugger{\"a}t wird von Falk G{\"o}tten und Felix Finger im Rahmen einer EFRE-F{\"o}rderung entwickelt.}, language = {de} } @article{DachwaldWi2007, author = {Dachwald, Bernd and Wi, Bong}, title = {Solar Sail Kinetic Energy Impactor Trajectory Optimization for an Asteroid-Deflection Mission}, series = {Journal of Spacecraft and Rockets. 44 (2007), H. 4}, journal = {Journal of Spacecraft and Rockets. 44 (2007), H. 4}, isbn = {0022-4650}, pages = {755 -- 764}, year = {2007}, language = {en} } @article{Dachwald2004, author = {Dachwald, Bernd}, title = {Minimum Transfer Times for Nonperfectly Reflecting Solar Sailcraft}, series = {Journal of Spacecraft and Rockets. 41 (2004), H. 4}, journal = {Journal of Spacecraft and Rockets. 41 (2004), H. 4}, isbn = {0022-4650}, pages = {693 -- 695}, year = {2004}, language = {en} } @article{Dachwald2004, author = {Dachwald, Bernd}, title = {Optimization of Interplanetary Solar Sailcraft Trajectories Using Evolutionary Neurocontrol}, series = {Journal of guidance, control, and dynamics. 27 (2004), H. 1}, journal = {Journal of guidance, control, and dynamics. 27 (2004), H. 1}, isbn = {0162-3192}, pages = {66 -- 72}, year = {2004}, language = {en} } @article{DachwaldOhndorfGill2009, author = {Dachwald, Bernd and Ohndorf, A. and Gill, E.}, title = {Optimization of low-thrust Earth-Moon transfers using evolutionary neurocontrol / Ohndorf, A. ; Dachwald, B. ; Gill, E.}, series = {IEEE Congress on Evolutionary Computation, 2009. CEC '09.}, journal = {IEEE Congress on Evolutionary Computation, 2009. CEC '09.}, isbn = {978-1-4244-2958-5}, pages = {358 -- 364}, year = {2009}, language = {en} } @article{ScholzRomagnoliDachwaldetal.2011, author = {Scholz, Christina and Romagnoli, Daniele and Dachwald, Bernd and Theil, Stephan}, title = {Performance analysis of an attitude control system for solar sails using sliding masses}, series = {Advances in Space Research}, volume = {48}, journal = {Advances in Space Research}, number = {11}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0273-1177}, pages = {1822 -- 1835}, year = {2011}, language = {en} }