@inproceedings{ŠakićMilijašMarinkovićetal.2021, author = {Šakić, Bogdan and Milijaš, Aleksa and Marinković, Marko and Butenweg, Christoph and Klinkel, Sven}, title = {Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load}, series = {8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering}, booktitle = {8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering}, editor = {Papadrakakis, Manolis and Fragiadakis, Michalis}, publisher = {National Technical University of Athens}, address = {Athen}, isbn = {9786188507258}, issn = {2623-3347}, doi = {10.7712/120121.8527.18913}, pages = {808 -- 828}, year = {2021}, abstract = {Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic.}, language = {en} } @inproceedings{OegunKlingHeuermannetal.2014, author = {{\"O}gun, Celal Mohan and Kling, Rainer and Heuermann, Holger and Gr{\"a}ser, Ulrich and Schopp, Christoph}, title = {Elektrodenlose quecksilberfreie Niederdrucklampen betrieben mit Mikrowellen}, series = {Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband}, booktitle = {Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband}, publisher = {Nederlandse Stichting voor Verlichtingskunde}, address = {Ede}, pages = {[Elektronische Ressource]}, year = {2014}, language = {de} } @inproceedings{ZaehlTheisWolfetal.2023, author = {Z{\"a}hl, Philipp M. and Theis, Sabine and Wolf, Martin and K{\"o}hler, Klemens}, title = {Teamwork in software development and what personality has to do with it - an overview}, series = {Virtual, Augmented and Mixed Reality}, booktitle = {Virtual, Augmented and Mixed Reality}, editor = {Chen, Jessie Y. C. and Fragomeni, Gino}, publisher = {Springer}, address = {Cham}, isbn = {978-3-031-35633-9 (Print)}, doi = {10.1007/978-3-031-35634-6_10}, pages = {130 -- 153}, year = {2023}, abstract = {Due to the increasing complexity of software projects, software development is becoming more and more dependent on teams. The quality of this teamwork can vary depending on the team composition, as teams are always a combination of different skills and personality types. This paper aims to answer the question of how to describe a software development team and what influence the personality of the team members has on the team dynamics. For this purpose, a systematic literature review (n=48) and a literature search with the AI research assistant Elicit (n=20) were conducted. Result: A person's personality significantly shapes his or her thinking and actions, which in turn influences his or her behavior in software development teams. It has been shown that team performance and satisfaction can be strongly influenced by personality. The quality of communication and the likelihood of conflict can also be attributed to personality.}, language = {en} } @inproceedings{ZaehlBiewendtWolfetal.2022, author = {Z{\"a}hl, Philipp M. and Biewendt, Marcel and Wolf, Martin and Eggert, Mathias}, title = {Requirements for Competence Developing Games in the Environment of SE Competence Development}, series = {Angewandte Forschung in der Wirtschaftsinformatik 2022}, booktitle = {Angewandte Forschung in der Wirtschaftsinformatik 2022}, publisher = {GITO}, address = {Berlin}, isbn = {978-3-95545-409-8}, doi = {10.30844/AKWI_2022_05}, pages = {73 -- 88}, year = {2022}, abstract = {Many of today's factors make software development more and more complex, such as time pressure, new technologies, IT security risks, et cetera. Thus, a good preparation of current as well as future software developers in terms of a good software engineering education becomes progressively important. As current research shows, Competence Developing Games (CDGs) and Serious Games can offer a potential solution. This paper identifies the necessary requirements for CDGs to be conducive in principle, but especially in software engineering (SE) education. For this purpose, the current state of research was summarized in the context of a literature review. Afterwards, some of the identified requirements as well as some additional requirements were evaluated by a survey in terms of subjective relevance.}, language = {en} } @inproceedings{ZugNiemuellerHochgeschwenderetal.2017, author = {Zug, Sebastian and Niemueller, Tim and Hochgeschwender, Nico and Seidensticker, Kai and Seidel, Martin and Friedrich, Tim and Neumann, Tobias and Karras, Ulrich and Kraetzschmar, Gerhard K. and Ferrein, Alexander}, title = {An Integration Challenge to Bridge the Gap Among Industry-Inspired RoboCup Leagues}, series = {RoboCup 2016: Robot World Cup XX. RoboCup 2016.}, booktitle = {RoboCup 2016: Robot World Cup XX. RoboCup 2016.}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-68792-6}, doi = {10.1007/978-3-319-68792-6_13}, pages = {157 -- 168}, year = {2017}, language = {en} } @inproceedings{ZischankKernFrentzeletal.2000, author = {Zischank, Wolfgang J. and Kern, Alexander and Frentzel, Ralf and Heidler, Fridolin and Seevers, M.}, title = {Assessment of the lightning transient coupling to control cables interconnecting structures in large industrial facilities and power plants}, year = {2000}, abstract = {Large industrial facilities and power plants often require a huge number fo information and control cables between the differnet structures. These I\&C-cables can be routed in reinforced concrete cable ducts or in isolated buried cable runs. KTA 2206 is the German lightning protection standard for nuclear power plants. During the last several years considerable effort has been made to revise this standard. Despite the well established principles and design guidelines for the construction of the lightning protection system, this standard puts special emphasis on the coupling of transient overvoltages to I\&C-cables.}, language = {en} } @inproceedings{ZischankHeidlerWiesingeretal.2004, author = {Zischank, Wolfgang J. and Heidler, Fridolin and Wiesinger, J. and Stimper, K. and Kern, Alexander and Seevers, M.}, title = {Magnetic Fields and Induced Voltages inside LPZ 1 Measured at a 1:6 Scale Model Building}, year = {2004}, abstract = {Laborexperimente zu Blitzschutzzonen in Stahlbetongeb{\"a}uden anhand eines Modells im Maßstab 1:6}, language = {en} } @inproceedings{ZischankHeidlerKernetal.2002, author = {Zischank, Wolfgang J. and Heidler, Fridolin and Kern, Alexander and Metwally, I. A. and Wiesinger, J. and Seevers, M.}, title = {Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages}, year = {2002}, abstract = {In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between "floor" and "roof" in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived.}, language = {en} } @inproceedings{ZiolkoFrickeAnthrakidisetal.2011, author = {Ziolko, Christoph and Fricke, Barbara and Anthrakidis, Anette and Hoffschmidt, Bernhard and Dillig, Marius and Giese, Frank and Schwarzb{\"o}zl, Peter}, title = {{\"O}kobilanzielle Aspekte technologischer Entwicklungen des Solarturmkraftwerks}, series = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster}, booktitle = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster}, publisher = {DLR}, address = {K{\"o}ln}, pages = {2 S.}, year = {2011}, language = {de} } @inproceedings{ZiolkoSchmitzSattleretal.2010, author = {Ziolko, C. and Schmitz, M. and Sattler, Johannes, Christoph and Khedim, Ahmed and Hoffschmidt, Bernhard}, title = {AlSol - the open volumetric receiver technology moves to Africa}, series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France}, booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France}, publisher = {Soc. OSC}, address = {Saint Maur}, pages = {93 -- 94}, year = {2010}, language = {en} } @inproceedings{ZingsheimGrimmerOrtneretal.2019, author = {Zingsheim, Jonas and Grimmer, Timo and Ortner, Marion and Schmaderer, Christoph and Hauser, Christine and Kotliar, Konstantin}, title = {Recognition of subjects with mild cognitive impairment (MCI) by the use of retinal arterial vessels.}, series = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen}, booktitle = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen}, editor = {Staat, Manfred and Erni, Daniel}, publisher = {Universit{\"a}t Duisburg-Essen}, address = {Duisburg}, organization = {MedTech Symposium}, isbn = {978-3-940402-22-6}, doi = {10.17185/duepublico/48750}, pages = {36 -- 37}, year = {2019}, language = {en} } @inproceedings{ZillerDoering2003, author = {Ziller, Claudia and D{\"o}ring, Bernd}, title = {Influence of the external dynamic wind pressure on the ventilation of double facades}, series = {Research in building physics: proceedings of the Second International Conference on Building Physics : Leuven, Belgium, 14-18 September 2003}, booktitle = {Research in building physics: proceedings of the Second International Conference on Building Physics : Leuven, Belgium, 14-18 September 2003}, editor = {Carmeliet, J. and Hens, H. and Vermeir, G.}, publisher = {Taylor and Francis}, address = {Hoboken}, organization = {International Conference on Building Physics <2, 2003, Leuven>}, isbn = {9058095657, 9789058095657}, pages = {527 -- 533}, year = {2003}, language = {en} } @inproceedings{ZieglerSchuellerMottaghy2013, author = {Ziegler, M. and Sch{\"u}ller, R. and Mottaghy, Darius}, title = {Numerical simulation of energy consumption of artificial ground freezing applications subject to water seepage}, series = {Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013}, booktitle = {Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013}, pages = {2985 -- 2988}, year = {2013}, language = {en} } @inproceedings{ZangHessRingbecketal.2002, author = {Zang, Zhigang and Hess, Holger and Ringbeck, Thorsten and Schwarte, Rudolf}, title = {Phase-lock techniques using new correlation receivers for TOF-laser ranging}, series = {Laser radar technology and applications VII : 3 - 4 April 2002, Orlando, USA. - (SPIE proceedings series ; 4723)}, booktitle = {Laser radar technology and applications VII : 3 - 4 April 2002, Orlando, USA. - (SPIE proceedings series ; 4723)}, editor = {Kamerman, Gary W.}, publisher = {SPIE, International Society for Optical Engineering}, address = {Bellingham, Wash.}, isbn = {0-8194-4473-1}, issn = {0038-7355}, pages = {112 -- 120}, year = {2002}, language = {en} } @inproceedings{ZahraPhaniSrujanCaminosetal.2022, author = {Zahra, Mahdi and Phani Srujan, Merige and Caminos, Ricardo Alexander Chico and Schmitz, Pascal and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e} and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and Dersch, J{\"u}rgen}, title = {Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants}, series = {SOLARPACES 2020}, booktitle = {SOLARPACES 2020}, number = {2445 / 1}, publisher = {AIP conference proceedings / American Institute of Physics}, address = {Melville, NY}, isbn = {978-0-7354-4195-8}, issn = {1551-7616 (online)}, doi = {10.1063/5.0086268}, pages = {9 Seiten}, year = {2022}, abstract = {Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica.}, language = {en} } @inproceedings{ZahnBerndtFehrenbach1973, author = {Zahn, Helmut and Berndt, Heinz and Fehrenbach, P.}, title = {Synthese cyclischer Cystinpeptide mit Insulin A-und B-Kettensequenzen}, series = {Peptides 1972 : proceedings of the Twelfth European Peptide Symposium, Reinhardsbrunn Castle, German Democratic Republic, September 1972}, booktitle = {Peptides 1972 : proceedings of the Twelfth European Peptide Symposium, Reinhardsbrunn Castle, German Democratic Republic, September 1972}, editor = {Hanson, Horst}, publisher = {North-Holland Publ. [u.a.],}, address = {Amsterdam [u.a.]}, isbn = {0-7204-4132-3}, pages = {101 -- 102}, year = {1973}, language = {de} } @inproceedings{YoshinobuMiyamotoWagneretal.2012, author = {Yoshinobu, Tatsuo and Miyamoto, Ko-Ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef}, title = {Miniaturized and high-speed chemical imaging systems}, series = {Nano-Biomedical Engineering 2012. Proceedings of the Tohoku University Global Centre of Excellence Programme, Sakura Hall, Tohoku University, Sendai Japan, 5 - 6 March 2012}, booktitle = {Nano-Biomedical Engineering 2012. Proceedings of the Tohoku University Global Centre of Excellence Programme, Sakura Hall, Tohoku University, Sendai Japan, 5 - 6 March 2012}, editor = {Yamaguchi, Takami}, publisher = {World Scientific}, address = {Singapur}, doi = {10.1142/9781848169067_0045}, pages = {386 -- 395}, year = {2012}, language = {en} } @inproceedings{YoshinobuSchoeningFingeretal.2003, author = {Yoshinobu, T. and Sch{\"o}ning, Michael Josef and Finger, F. and Moritz, W. and Iwasaki, H.}, title = {Thin-film a-Si LAPS : Preparation and pH sensitivity}, series = {Eurosensors XVII : the 17th European Conference on Solid-State Transducers ; University of Minho, Guimar{\~a}es, Portugal, September 21 - 24, 2003}, booktitle = {Eurosensors XVII : the 17th European Conference on Solid-State Transducers ; University of Minho, Guimar{\~a}es, Portugal, September 21 - 24, 2003}, pages = {88 -- 89}, year = {2003}, language = {en} } @inproceedings{XuSchwarteHeinoletal.1998, author = {Xu, Zhanping and Schwarte, Rudolf and Heinol, Horst-Guenther and Buxbaum, Bernd and Ringbeck, Thorsten}, title = {Smart pixel : photonic mixer device (PMD) ; new system concept of a 3D-imaging camera-on-a-chip}, series = {Proceedings : M2VIP '98; Nanjing, China, 10th - 12th September 1998}, booktitle = {Proceedings : M2VIP '98; Nanjing, China, 10th - 12th September 1998}, editor = {Cheung, Edmund H. M.}, address = {Hong Kong}, isbn = {962-442-129-3}, pages = {259 -- 264}, year = {1998}, language = {en} } @inproceedings{WuttkeButenwegRosinetal.2019, author = {Wuttke, Claudia and Butenweg, Christoph and Rosin, Julia and Kubalski, Thomas}, title = {Verbesserte seismische Nachweiskonzepte f{\"u}r Mauerwerksbauten in deutschen Erdbebengebieten}, series = {Adam, Christoph (Hrsg.) ; Univ. Innsbruck: 16. D-A-CH Tagung Erdbebeningenieurwesen \& Baudynamik 2019 : 26. und 27. September 2019, Innsbruck}, booktitle = {Adam, Christoph (Hrsg.) ; Univ. Innsbruck: 16. D-A-CH Tagung Erdbebeningenieurwesen \& Baudynamik 2019 : 26. und 27. September 2019, Innsbruck}, address = {Innsbruck}, isbn = {978-3-200-06454-6}, pages = {713 -- 722}, year = {2019}, language = {de} } @inproceedings{WulfhorstMerseburgTippkoetter2015, author = {Wulfhorst, Helene and Merseburg, Johannes and Tippk{\"o}tter, Nils}, title = {Analyse von Lignocellulose mittels dynamischer Differenzkalorimetrie und Infrarot - Spektrometrie}, series = {12. Dresdner Sensor-Symposium 2015 2015-12-07 - 2015-12-09}, booktitle = {12. Dresdner Sensor-Symposium 2015 2015-12-07 - 2015-12-09}, isbn = {978-3-9813484-9-1}, doi = {10.5162/12dss2015/P6.2}, pages = {210 -- 215}, year = {2015}, language = {de} } @inproceedings{WulfhorstDuweMoehringetal.2016, author = {Wulfhorst, H. and Duwe, A. and M{\"o}hring, S. and Jurca, O. and Tippk{\"o}tter, Nils}, title = {Analysis of pretreated biomass by differential scanning 132 calorimetry and multivariate data analysis}, series = {New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany}, booktitle = {New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany}, publisher = {DECHEMA}, address = {Frankfurt am Main}, pages = {132}, year = {2016}, language = {en} } @inproceedings{WuKemper2016, author = {Wu, Ziyi and Kemper, Hans}, title = {The optimal 48 V - battery pack for a specific load profile of a heavy duty vehicle}, series = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland}, booktitle = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland}, year = {2016}, language = {en} } @inproceedings{WuPoghossianWerneretal.2013, author = {Wu, Chunsheng and Poghossian, Arshak and Werner, Frederik and Bronder, Thomas and B{\"a}cker, Matthias and Wang, Ping and Sch{\"o}ning, Michael Josef}, title = {An application of a scanning light-addressable potentiometric sensor for label-free DNA detection}, series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013}, booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013}, organization = {Dresdner Sensor-Symposium <11, 2013>}, isbn = {978-3-9813484-5-3}, pages = {164 -- 168}, year = {2013}, language = {en} } @inproceedings{WuBronderPoghossianetal.2014, author = {Wu, Chunsheng and Bronder, Thomas and Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {DNA-hybridization detection using light-addressable potentiometric sensor modified with gold layer}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 4}, year = {2014}, language = {en} } @inproceedings{WollertVedral2005, author = {Wollert, J{\"o}rg and Vedral, Andreas}, title = {Bluetooth - Integrationstechnologie f{\"u}r automotive Anwendungen}, series = {Begleittexte zum Entwicklerforum ZigBee \& Co. - Drahtlose Nahbereichsnetzwerke : 20. April 2005, M{\"u}nchen-Dornach}, booktitle = {Begleittexte zum Entwicklerforum ZigBee \& Co. - Drahtlose Nahbereichsnetzwerke : 20. April 2005, M{\"u}nchen-Dornach}, organization = {Entwicklerforum ZigBee \& Co. - Drahtlose Nahbereichsnetzwerke <2005, Aschheim-Dornach>}, year = {2005}, language = {de} } @inproceedings{WollertVedral2002, author = {Wollert, J{\"o}rg and Vedral, Andreas}, title = {Einsatz von Opensource-Software f{\"u}r Evaluationsprototypen : Anwendungsempfehlungen und Einsatzbeispiele}, series = {Vortr{\"a}ge und Begleittexte zum Entwicklerforum Wireless 2002 : Technologien und Grundlagen ; 16. Mai 2002}, booktitle = {Vortr{\"a}ge und Begleittexte zum Entwicklerforum Wireless 2002 : Technologien und Grundlagen ; 16. Mai 2002}, publisher = {Design \& Elektronik}, address = {Poing}, organization = {Entwicklerforum Wireless <2002, M{\"u}nchen>}, pages = {37 -- 46}, year = {2002}, language = {de} } @inproceedings{WollertRau2012, author = {Wollert, J{\"o}rg and Rau, S.}, title = {Performance von embedded WLAN-Systemen bei koexistierenden Netzwerken}, series = {KOMMA 2012 : Kommunikation in der Automation : 3. Jahreskolloquium Kommunikation in der Automation : Lemgo, 14.11.2012 / J{\"u}rgen Jasperneite ... (Hrsg.)}, booktitle = {KOMMA 2012 : Kommunikation in der Automation : 3. Jahreskolloquium Kommunikation in der Automation : Lemgo, 14.11.2012 / J{\"u}rgen Jasperneite ... (Hrsg.)}, publisher = {Inst. f{\"u}r Industrielle Informationstechnik}, address = {Lemgo}, organization = {Jahreskolloquium Kommunikation in der Automation <3, 2012, Lemgo>}, isbn = {978-3-9814062-2-1}, pages = {1 CD-ROM}, year = {2012}, language = {de} } @inproceedings{WollertPlessmann1993, author = {Wollert, J{\"o}rg and Plessmann, K. W.}, title = {Controlling processes by operating-point based hybride observers}, series = {EUFIT '93 : September 7 - 10, 1993, Eurogress Aachen, Germany, proceedings / First European Congress on Fuzzy and Intelligent Technologies}, booktitle = {EUFIT '93 : September 7 - 10, 1993, Eurogress Aachen, Germany, proceedings / First European Congress on Fuzzy and Intelligent Technologies}, publisher = {Verl. d. Augustinus Buchh.}, address = {Aachen}, organization = {EUFIT <1, 1993, Aachen>}, isbn = {3-86073-176-9}, pages = {1151 -- 1155}, year = {1993}, language = {en} } @inproceedings{Wollert2006, author = {Wollert, J{\"o}rg}, title = {Langzeitstatistische Untersuchungen zur Qualit{\"a}t von Funkkan{\"a}len f{\"u}r das industrielle Umfeld}, series = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)}, booktitle = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, isbn = {3-18-377210-8}, pages = {165 -- 176}, year = {2006}, language = {de} } @inproceedings{Wollert2006, author = {Wollert, J{\"o}rg}, title = {Grundlagen Wireless - Was kann von Funktechnik erwartet werden?}, series = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund / J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)}, booktitle = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund / J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, isbn = {3-18-377210-8}, pages = {314 -- 323}, year = {2006}, language = {de} } @inproceedings{Wollert2008, author = {Wollert, J{\"o}rg}, title = {Technologischer {\"U}berblick - welches ist die richtige kabellose Technologie? Grenzen und M{\"o}glichkeiten der Funk{\"u}bertragung sowie der konkreten Nutzung verschiedener Technolgien}, series = {Wireless-Technologies-Kongress 2008 : von der Technologie zur Anwendung / Hrsg. J{\"o}rg F. Wollert}, booktitle = {Wireless-Technologies-Kongress 2008 : von der Technologie zur Anwendung / Hrsg. J{\"o}rg F. Wollert}, publisher = {AKA}, address = {Heidelberg}, organization = {Wireless-Technologies-Kongress <10, 2008, Bochum>}, isbn = {978-3-89838-608-1}, pages = {349}, year = {2008}, language = {de} } @inproceedings{Wollert2010, author = {Wollert, J{\"o}rg}, title = {Grundlagen Wireless Technologie}, series = {Wireless Technologies : 12. Kongress, 22. - 23. September 2010, Bochum ; von der Technologie zur Anwendung / J{\"o}rg F. Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; 810)}, booktitle = {Wireless Technologies : 12. Kongress, 22. - 23. September 2010, Bochum ; von der Technologie zur Anwendung / J{\"o}rg F. Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; 810)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, pages = {322 -- 330}, year = {2010}, language = {de} } @inproceedings{Wollert1994, author = {Wollert, J{\"o}rg}, title = {Hybride arbeitspunktabh{\"a}ngige Beobachter zur intelligenten Modellierung und Regelung nichtlinearer Strecken}, series = {Fuzzy control : GMA-Aussprachetag ; Tagung Langen, 22. und 23. M{\"a}rz 1994. (VDI-Berichte ; 1113)}, booktitle = {Fuzzy control : GMA-Aussprachetag ; Tagung Langen, 22. und 23. M{\"a}rz 1994. (VDI-Berichte ; 1113)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Meß- und Automatisierungstechnik}, isbn = {3-18-091113-1}, pages = {497 -- 506}, year = {1994}, language = {de} } @inproceedings{Wollert2012, author = {Wollert, J{\"o}rg}, title = {The performance of UWB-communication in an industrial environment}, series = {IEEE 1st International Symposium on Wireless Systems : (IDAACS-SWS) : Offenburg, 20-21 Sept. 2012}, booktitle = {IEEE 1st International Symposium on Wireless Systems : (IDAACS-SWS) : Offenburg, 20-21 Sept. 2012}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {International Symposium on Wireless Systems <1, 2012, Offenburg>}, isbn = {978-1-4673-4678-8}, doi = {10.1109/IDAACS-SWS.2012.6377639}, pages = {85 -- 90}, year = {2012}, language = {en} } @inproceedings{Wollert2007, author = {Wollert, J{\"o}rg}, title = {Mobility - Integration von Offboard-Devices in Fahrzeugen}, series = {Begleittexte zum Entwicklerforum Kfz-Elektronik \& FlexRay Solution Day : 15. Mai 2007, Ludwigsburg / hrsg. von Caspar Grote ...}, booktitle = {Begleittexte zum Entwicklerforum Kfz-Elektronik \& FlexRay Solution Day : 15. Mai 2007, Ludwigsburg / hrsg. von Caspar Grote ...}, publisher = {Design \& Elektronik}, address = {Poing}, pages = {47 -- 54}, year = {2007}, language = {de} } @inproceedings{Wollert2007, author = {Wollert, J{\"o}rg}, title = {Fahrzeug-Umwelt Kommunikation? Chancen und Herausforderungen}, series = {Begleittexte zum Entwicklerforum Kfz-Elektronik \& FlexRay Solution Day : 15. Mai 2007, Ludwigsburg / hrsg. von Caspar Grote ...}, booktitle = {Begleittexte zum Entwicklerforum Kfz-Elektronik \& FlexRay Solution Day : 15. Mai 2007, Ludwigsburg / hrsg. von Caspar Grote ...}, publisher = {Design \& Elektronik}, address = {Poing}, pages = {39 -- 46}, year = {2007}, language = {de} } @inproceedings{Wollert2008, author = {Wollert, J{\"o}rg}, title = {Performanceanforderungen von Funkstrecken in der Prozess- und Fertigungsautomation}, series = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)}, booktitle = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {Automatisierungskongress <2008, Baden-Baden>}, isbn = {978-3-18-092032-0}, pages = {247 -- 248}, year = {2008}, language = {de} } @inproceedings{Wollert1997, author = {Wollert, J{\"o}rg}, title = {Echtzeitl{\"o}sungen f{\"u}r Windows NT}, series = {Kongreßband = Conference proceedings / Echtzeit '97, Kongreß \& Messe f{\"u}r Industrielle Busse und Netze; INet '97, Kongreß \& Messe f{\"u}r Industrielle Computer-Anwendungen, 9. - 11. September 1997, Wiesbaden}, booktitle = {Kongreßband = Conference proceedings / Echtzeit '97, Kongreß \& Messe f{\"u}r Industrielle Busse und Netze; INet '97, Kongreß \& Messe f{\"u}r Industrielle Computer-Anwendungen, 9. - 11. September 1997, Wiesbaden}, address = {Wiesbaden}, pages = {13 -- 29}, year = {1997}, language = {de} } @inproceedings{Wollert1999, author = {Wollert, J{\"o}rg}, title = {Harte Echtzeit f{\"u}r Windows}, series = {Tagungsband : SPS/IPC/Drives '99 : 10. Fachmesse und Kongress, 23. - 25. November 1999 N{\"u}rnberg}, booktitle = {Tagungsband : SPS/IPC/Drives '99 : 10. Fachmesse und Kongress, 23. - 25. November 1999 N{\"u}rnberg}, publisher = {H{\"u}thig}, address = {Heidelberg}, organization = {SPS IPC Drives <10, 1999, N{\"u}rnberg>}, isbn = {3-7785-2788-6}, pages = {172 -- 182}, year = {1999}, language = {de} } @inproceedings{Wollert2000, author = {Wollert, J{\"o}rg}, title = {Echtzeiteigenschaften f{\"u}r Automatisierungsanwendungen mit Ethernet und TCP/IP}, series = {Tagungsband - SPS/IPC/Drives 2000 : elektrische Automatisierung - Systeme und Komponenten ; 11. Fachmesse \& Kongress 28. - 30. Nov. 2000, N{\"u}rnberg. (Praxiswissen : Automatisierung)}, booktitle = {Tagungsband - SPS/IPC/Drives 2000 : elektrische Automatisierung - Systeme und Komponenten ; 11. Fachmesse \& Kongress 28. - 30. Nov. 2000, N{\"u}rnberg. (Praxiswissen : Automatisierung)}, publisher = {H{\"u}thig}, address = {Heidelberg}, organization = {SPS IPC Drives <11, 2000, N{\"u}rnberg>}, isbn = {3-7785-2836-X}, pages = {124 -- 132}, year = {2000}, language = {de} } @inproceedings{Wollert2000, author = {Wollert, J{\"o}rg}, title = {Internettechnologie und Multimedia f{\"u}r Steuerungssysteme}, series = {Tagungsband - SPS/IPC/Drives 2000 : elektrische Automatisierung - Systeme und Komponenten ; 11. Fachmesse \& Kongress 28. - 30. Nov. 2000, N{\"u}rnberg. (Praxiswissen : Automatisierung)}, booktitle = {Tagungsband - SPS/IPC/Drives 2000 : elektrische Automatisierung - Systeme und Komponenten ; 11. Fachmesse \& Kongress 28. - 30. Nov. 2000, N{\"u}rnberg. (Praxiswissen : Automatisierung)}, publisher = {H{\"u}thig}, address = {Heidelberg}, organization = {SPS IPC Drives <11, 2000, N{\"u}rnberg>}, isbn = {3-7785-2836-X}, pages = {78 -- 86}, year = {2000}, language = {de} } @inproceedings{Wollert2001, author = {Wollert, J{\"o}rg}, title = {10 Regeln f{\"u}r das Desaster}, series = {Logistik IT Erfolgsfaktor oder Risiko? : Tagung R{\"u}sselsheim, 14. und 15. November 2001. (VDI-Berichte ; 1633)}, booktitle = {Logistik IT Erfolgsfaktor oder Risiko? : Tagung R{\"u}sselsheim, 14. und 15. November 2001. (VDI-Berichte ; 1633)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {Gesellschaft F{\"o}rdertechnik, Materialfluss und Logistik}, isbn = {3-18-091633-8}, pages = {1 -- 16}, year = {2001}, language = {de} } @inproceedings{Wollert2003, author = {Wollert, J{\"o}rg}, title = {Ein Low-Power Bordrechner als Kommunikationsgateway f{\"u}r den Automotive-Bereich}, series = {Bluetooth : 4. Kongress, Dortmund, 29. - 30 Januar 2003}, booktitle = {Bluetooth : 4. Kongress, Dortmund, 29. - 30 Januar 2003}, publisher = {Mesago Messe Frankfurt GmbH}, address = {Stuttgart}, pages = {1 -- 9}, year = {2003}, language = {de} } @inproceedings{Wollert2003, author = {Wollert, J{\"o}rg}, title = {Einsatz von Wireless Technologien im Kraftfahrzeug}, series = {Sichere Datenkommunikation im Automobil : Kongress ; 18. - 19. November 2003, Radisson SAS Hotel, K{\"o}ln}, booktitle = {Sichere Datenkommunikation im Automobil : Kongress ; 18. - 19. November 2003, Radisson SAS Hotel, K{\"o}ln}, address = {K{\"o}ln}, organization = {ESCAR-Tagung <2003, K{\"o}ln>}, pages = {Getr. Z{\"a}hlung}, year = {2003}, language = {de} } @inproceedings{Wollert1994, author = {Wollert, J{\"o}rg}, title = {Modellierung intelligenter Regelungen mit analytischen und heuristischen Merkmalen}, series = {39. Internationales Wissenschaftliches Kolloquium / Technische Universit{\"a}t Ilmenau, Th{\"u}ringen : 27.-30.09.1994}, booktitle = {39. Internationales Wissenschaftliches Kolloquium / Technische Universit{\"a}t Ilmenau, Th{\"u}ringen : 27.-30.09.1994}, publisher = {Techn. Univ.}, address = {Ilmenau}, organization = {Technische Universit{\"a}t }, issn = {0943-7207}, pages = {181 -- 188}, year = {1994}, language = {de} } @inproceedings{Wollert1994, author = {Wollert, J{\"o}rg}, title = {Objekt-orientierte Modellierung hybrider Systeme mit heuristischen und analytischen Merkmalen}, series = {Berichtsband / 4. Workshop "Fuzzy Control" des GMA-UA 1.4.2. am 03./04.11.1994 in Dortmund. (Forschungsbericht / Universit{\"a}t Dortmund, Fakult{\"a}t f{\"u}r Elektrotechnik ; 1/94)}, booktitle = {Berichtsband / 4. Workshop "Fuzzy Control" des GMA-UA 1.4.2. am 03./04.11.1994 in Dortmund. (Forschungsbericht / Universit{\"a}t Dortmund, Fakult{\"a}t f{\"u}r Elektrotechnik ; 1/94)}, publisher = {Univ., Fak. f. Elektrotechnik}, address = {Dortmund}, pages = {246 -- 257}, year = {1994}, language = {de} } @inproceedings{Wollert2003, author = {Wollert, J{\"o}rg}, title = {Wireless-Technologie - eine neue Chance f{\"u}r lokationsbezogene Dienste}, series = {SPS/IPC/DRIVES 2003 : SPS/IPC/DRIVES/Elektrische Automatisierung - Systeme und Komponenten, Fachmesse \& Kongress 25. - 27. Nov. 2003, N{\"u}rnberg ; [Tagungsband]}, booktitle = {SPS/IPC/DRIVES 2003 : SPS/IPC/DRIVES/Elektrische Automatisierung - Systeme und Komponenten, Fachmesse \& Kongress 25. - 27. Nov. 2003, N{\"u}rnberg ; [Tagungsband]}, publisher = {VDE-Verl.}, address = {Berlin [u.a.]}, isbn = {3-8007-2793-5}, pages = {253 -- 260}, year = {2003}, language = {de} } @inproceedings{Wollert2004, author = {Wollert, J{\"o}rg}, title = {Sicherheit und Sicherheitsl{\"u}cken in kabellosen Automatisierungsnetzwerken : wieviel Sicherheit braucht ein Automatisierungsnetzwerk?}, series = {Funkgest{\"u}tzte Kommunikation in der industriellen Automatisierungstechnik : Tagung D{\"u}sseldorf, 4. und 5. Mai 2004. (VDI-Berichte ; 1843)}, booktitle = {Funkgest{\"u}tzte Kommunikation in der industriellen Automatisierungstechnik : Tagung D{\"u}sseldorf, 4. und 5. Mai 2004. (VDI-Berichte ; 1843)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, isbn = {3-18-091843-8}, pages = {91 -- 104}, year = {2004}, language = {de} } @inproceedings{Wollert2002, author = {Wollert, J{\"o}rg}, title = {Bluetooth in Embedded-Anwendungen in der Automatisierungstechnik}, series = {Tagungsband / SPS IPC Drives 2002 : 13. Fachmesse und Kongress, 26. - 28. November 2002 N{\"u}rnberg; elektrische Automatisierung - Systeme und Komponenten. (Praxiswissen IEE - Automatisierung)}, booktitle = {Tagungsband / SPS IPC Drives 2002 : 13. Fachmesse und Kongress, 26. - 28. November 2002 N{\"u}rnberg; elektrische Automatisierung - Systeme und Komponenten. (Praxiswissen IEE - Automatisierung)}, publisher = {H{\"u}thig}, address = {Heidelberg}, isbn = {3-7785-2863-7}, pages = {28 -- 37}, year = {2002}, language = {de} } @inproceedings{Wollert1997, author = {Wollert, J{\"o}rg}, title = {Windows und Echtzeit? - Ein kritischer Blick auf Windows NT als Echtzeitbetriebssystem}, series = {Tagungsband / 8. Int. Fachmesse und Kongress f{\"u}r Speicherprogrammierbare Steuerungen, Industrie-PCs und Elektrische Antriebstechnik, N{\"u}rnberg, 25. - 27. Nov. 1997; SPS IPC Drives}, booktitle = {Tagungsband / 8. Int. Fachmesse und Kongress f{\"u}r Speicherprogrammierbare Steuerungen, Industrie-PCs und Elektrische Antriebstechnik, N{\"u}rnberg, 25. - 27. Nov. 1997; SPS IPC Drives}, publisher = {H{\"u}thig}, address = {Heidelberg}, organization = {SPS IPC Drives <8, 1997, N{\"u}rnberg>}, isbn = {3-7785-2683-9}, pages = {250 -- 260}, year = {1997}, language = {de} } @inproceedings{Wollert2004, author = {Wollert, J{\"o}rg}, title = {Sicherheit in kabellosen Netzwerken}, series = {SPS/IPC/DRIVES 2004 : SPS/IPC/DRIVES, Elektrische Automatisierung - Systeme und Komponenten, Fachmesse \& Kongress, 23. - 25. Nov. 2004, N{\"u}rnberg}, booktitle = {SPS/IPC/DRIVES 2004 : SPS/IPC/DRIVES, Elektrische Automatisierung - Systeme und Komponenten, Fachmesse \& Kongress, 23. - 25. Nov. 2004, N{\"u}rnberg}, publisher = {Poing}, address = {Franzis}, isbn = {3-7723-6709-7}, pages = {335 -- 341}, year = {2004}, language = {de} } @inproceedings{Wollert2001, author = {Wollert, J{\"o}rg}, title = {Webbased Control technischer Anlagen}, series = {Virtuelle Laboratorien : Vortr{\"a}ge zum 52. Berg- und H{\"u}ttenm{\"a}nnischen Tag 2001 in Freiberg}, booktitle = {Virtuelle Laboratorien : Vortr{\"a}ge zum 52. Berg- und H{\"u}ttenm{\"a}nnischen Tag 2001 in Freiberg}, publisher = {TU Bergakademie}, address = {Freiberg}, organization = {Berg- und H{\"u}ttenm{\"a}nnischer Tag <52, 2001, Freiberg>}, isbn = {3860121456}, pages = {111 -- 120}, year = {2001}, language = {de} } @inproceedings{Wollert2016, author = {Wollert, J{\"o}rg}, title = {Industrie 4.0 - warten bis die Revolution vorbei ist?}, series = {Automatisierung im Fokus von Industrie 4.0 : Tagungsband AALE 2016 ; 13. Fachkonferenz, L{\"u}beck}, booktitle = {Automatisierung im Fokus von Industrie 4.0 : Tagungsband AALE 2016 ; 13. Fachkonferenz, L{\"u}beck}, publisher = {DIV Deutscher Industrieverlag GmbH}, address = {M{\"u}nchen}, isbn = {978-3-8356-7312-0}, pages = {127 -- 136}, year = {2016}, language = {de} } @inproceedings{Wollert2015, author = {Wollert, J{\"o}rg}, title = {Wireless systems for machinery safety : Requirements and solutions for wireless real time systems}, series = {16th International Conference on Research and Education in Mechatronics (REM), 2015}, booktitle = {16th International Conference on Research and Education in Mechatronics (REM), 2015}, isbn = {978-3-945728-01-7}, doi = {10.1109/REM.2015.7380377}, pages = {88 -- 91}, year = {2015}, language = {en} } @inproceedings{WolfWiese2013, author = {Wolf, Martin and Wiese, Ute}, title = {A comparative transformation model for process changes using serious games}, series = {2013 IEEE 2nd International Conference on Serious Games and Applications for Health (SeGAH): proceedings of a meeting held 2-3 May 2013, Algarve, Portugal}, booktitle = {2013 IEEE 2nd International Conference on Serious Games and Applications for Health (SeGAH): proceedings of a meeting held 2-3 May 2013, Algarve, Portugal}, publisher = {Institute of Electrical and Electronics Engineers (IEEE)}, address = {Piscataway, NJ}, organization = {International Conference on Serious Games and Applications for Health <2, 2013, Algarve>}, isbn = {978-1-4673-6164-4}, doi = {10.1109/SeGAH.2013.6665307}, pages = {64 -- 70}, year = {2013}, language = {en} } @inproceedings{WolfWiedenmaierSchlick1998, author = {Wolf, Martin and Wiedenmaier, S. and Schlick, Christopher}, title = {Flexible Kooperation durch computergest{\"u}tzte Teamarbeit}, series = {Groupware und organisatorische Innovation : Tagungsband der Deutschen Fachtagung zu Computer Supported Cooperative Work. - (Berichte des German Chapter of the ACM ; Bd. 51)}, booktitle = {Groupware und organisatorische Innovation : Tagungsband der Deutschen Fachtagung zu Computer Supported Cooperative Work. - (Berichte des German Chapter of the ACM ; Bd. 51)}, editor = {Herrmann, Thomas}, publisher = {Teubner}, address = {Stuttgart}, isbn = {3-519-02692-9}, pages = {349 -- 350}, year = {1998}, language = {de} } @inproceedings{WolfUlbrich2007, author = {Wolf, Martin and Ulbrich, Daniel}, title = {Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung}, year = {2007}, abstract = {Dr.-Ing. Martin Wolf ; Dipl.-Kaufm. Daniel Ulbrich , Dr. Pecher und Partner Ingenieurgesellschaft mbH, M{\"u}nchen. 31 S. (S. 139-168). Beitrag zum 1. Aachener Softwaretag in der Wasserwirtschaft < 1, 2007, Aachen>. Zusammenfasung [der Autoren] Die {\"o}ffentlichen Kanalnetze Deutschlands stellen mit einem Wert von rd. 330 Mrd. € ein enormes Anlageverm{\"o}gen dar. Auf Grund des oft schlechten Zustandes und geringer Ausgaben zur Instandhaltung und Erneuerung ist zu erwarten, dass durch die gegenw{\"a}rtige Sanierungspraxis eher ein Substanzwertverzehr des Kanalnetzes als ein Substanzwerterhalt im Sinne des Generationenvertrages erzielt wird. F{\"u}r einen nachhaltigen Betrieb und Erhalt der Kanalnetze sind deshalb Sanierungsstrategien erforderlich, die neben den technischen und gesetzlichen Anforderungen auch den mittel- und langfristigen Substanzwertverlauf ber{\"u}cksichtigen. Dieser wird beeinflusst vom erforderlichen oder durchgef{\"u}hrten Sanierungsumfang, Art und Zusammensetzung der ausgew{\"a}hlten Maßnahmen sowie der zeitlichen Abfolge der Sanierungsmaßnahmen. Erheblichen Einfluss auf den Substanzwertverlauf hat zudem die Ber{\"u}cksichtigung der hydraulischen Verh{\"a}ltnisse sowie der optisch nicht sichtbaren Undichtheiten. Entsprechend ist es erforderlich, die tats{\"a}chlich vorhandenen Defizite zu ermitteln und die Sanierungsmaßnahmen sowie eine Strategie zur Umsetzung zu erarbeiten. Da sich gezeigt hat, dass alleine die Einhaltung der technischen und gesetzlichen Anforderung f{\"u}r einen Substanzwerterhalt nicht ausreicht, muss die geplante Strategie im Dr.-Ing. Martin Wolf 139 von 170 Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung 1. Aachener Softwaretag in der Wasserwirtschaft Hinblick auf die nachhaltige Wertentwicklung {\"u}berpr{\"u}ft und ggf. Anpassungen vorgenommen werden. Kurzfristig erzielte Einsparungen durch reduzierten Schadensumfang oder einseitige Maßnahmenwahl erm{\"o}glichen zwar im g{\"u}nstigsten Fall, die Anforderungen einzuhalten, gehen jedoch zwangsl{\"a}ufig zu Lasten des Substanzwertes und f{\"u}hren mittel- und langfristig zu einer Versch{\"a}rfung der Kosten- und Geb{\"u}hrensituation. Der monet{\"a}re, am konkreten Sanierungsaufwand orientierte Substanzwertansatz erm{\"o}glicht dabei, technische und kaufm{\"a}nnische Gesichtspunkte praxisnah zu verkn{\"u}pfen und den bestm{\"o}glichen Ausgleich zwischen den gegenl{\"a}ufigen Zielen Substanzwerterhalt und Geb{\"u}hrenkonstanz zu finden.}, subject = {Kanalisation}, language = {de} } @inproceedings{WolfSchlickHerbstetal.1996, author = {Wolf, Martin and Schlick, Christopher and Herbst, D. and Springer, J.}, title = {Einflussfaktoren auf den Erfolg von Telekooperation in großen Unternehmen}, series = {Computer Supported Cooperative Work (CSCW) in großen Unternehmungen : Tagungsband zum Workshop der GI-Fachgruppe 5.5.1 "CSCW in Organisationen" und dem Technologiezentrum Darmstadt der Deutschen Telekom AG vom 09. - 10. Mai 1996}, booktitle = {Computer Supported Cooperative Work (CSCW) in großen Unternehmungen : Tagungsband zum Workshop der GI-Fachgruppe 5.5.1 "CSCW in Organisationen" und dem Technologiezentrum Darmstadt der Deutschen Telekom AG vom 09. - 10. Mai 1996}, editor = {Uellner, Stefan}, publisher = {Dt. Telekom}, address = {Darmstadt}, pages = {1 -- 12}, year = {1996}, language = {de} } @inproceedings{WolfLenz2015, author = {Wolf, Martin and Lenz, Laura L.}, title = {The economic effectiveness of serious games in the healthcare environment : application and evaluation of the Comparative Transformation Model (CTM)}, series = {IEEE 3rd International Conference on Serious Games and Applications for Health : SeGAH 2014 ; Rio de Janeiro, Brazil, May 14 - 16}, booktitle = {IEEE 3rd International Conference on Serious Games and Applications for Health : SeGAH 2014 ; Rio de Janeiro, Brazil, May 14 - 16}, publisher = {IEEE [u.a.]}, address = {Piscataway, NJ}, isbn = {978-1-4799-4823-9}, doi = {10.1109/SeGAH.2014.7067089}, pages = {135 -- 142}, year = {2015}, language = {en} } @inproceedings{WolfKoenig2017, author = {Wolf, Martin and K{\"o}nig, Johannes Alexander}, title = {Competence Developing Games - Ein {\"U}berblick}, series = {INFORMATIK 2017, Lecture Notes in Informatics (LNI), Gesellschaft f{\"u}r Informatik}, booktitle = {INFORMATIK 2017, Lecture Notes in Informatics (LNI), Gesellschaft f{\"u}r Informatik}, editor = {Eibl, Maximilian and Gaedke, Martin}, organization = {Gesellschaft f{\"u}r Informatik}, isbn = {978-3-88579-669-5}, doi = {10.18420/in2017_32}, pages = {385 -- 391}, year = {2017}, abstract = {Es existieren verschiedenste Arten von Spielen, die versuchen, die Motivation einer Spielsituation in einen ernsten Kontext zu {\"u}berf{\"u}hren. In diesem Artikel wird der {\"U}berbegriff „Competence Developing Games" definiert und anhand von Beispielen erl{\"a}utert. Daf{\"u}r werden Erkennungskriterien vorgestellt, entsprechende Spieltypen erl{\"a}utert und eine Zuordnung durch-gef{\"u}hrt.}, language = {de} } @inproceedings{WolfBartonHerrmannetal.2019, author = {Wolf, Martin and Barton, Thomas and Herrmann, Frank and Meister, Vera G. and M{\"u}ller, Christian and Seel, Christian}, title = {Angewandte Forschung in der Wirtschaftsinformatik 2019 : Tagungsband zur 32. AKWI-Jahrestagung vom 15.09.2019 bis 18.09.2019 an der Fachhochschule f{\"u}r Angewandte Wissenschaften Aachen / hrsg. von Martin R. Wolf, Thomas Barton, Frank Herrmann, Vera G. Meister, Christian M{\"u}ller, Christian Seel}, publisher = {mana-Buch}, address = {Heide}, isbn = {978-3-944330-62-4}, doi = {10.15771/978-3-944330-62-4}, url = {http://nbn-resolving.de/urn:nbn:de:kobv:526-opus4-13026}, pages = {261 Seiten}, year = {2019}, abstract = {Tagungsbeitr{\"a}ge aus den Bereichen Projektmanagement, Didaktik in der Wirtschaftsinformatik, IT-Sicherheit, Anwendungsf{\"a}lle, Reifegradmodelle, Plattformen f{\"u}r Gesch{\"a}ftsprozesse und Prototypen.}, language = {de} } @inproceedings{WittigRuettersBragard2024, author = {Wittig, M. and R{\"u}tters, Ren{\´e} and Bragard, Michael}, title = {Application of RL in control systems using the example of a rotatory inverted pendulum}, series = {Tagungsband AALE 2024 : Fit f{\"u}r die Zukunft: praktische L{\"o}sungen f{\"u}r die industrielle Automation}, booktitle = {Tagungsband AALE 2024 : Fit f{\"u}r die Zukunft: praktische L{\"o}sungen f{\"u}r die industrielle Automation}, editor = {Reiff-Stephan, J{\"o}rg and J{\"a}kel, Jens and Schwarz, Andr{\´e}}, publisher = {le-tex publishing services GmbH}, address = {Leipzig}, isbn = {978-3-910103-02-3}, doi = {10.33968/2024.53}, pages = {241 -- 248}, year = {2024}, abstract = {In this paper, the use of reinforcement learning (RL) in control systems is investigated using a rotatory inverted pendulum as an example. The control behavior of an RL controller is compared to that of traditional LQR and MPC controllers. This is done by evaluating their behavior under optimal conditions, their disturbance behavior, their robustness and their development process. All the investigated controllers are developed using MATLAB and the Simulink simulation environment and later deployed to a real pendulum model powered by a Raspberry Pi. The RL algorithm used is Proximal Policy Optimization (PPO). The LQR controller exhibits an easy development process, an average to good control behavior and average to good robustness. A linear MPC controller could show excellent results under optimal operating conditions. However, when subjected to disturbances or deviations from the equilibrium point, it showed poor performance and sometimes instable behavior. Employing a nonlinear MPC Controller in real time was not possible due to the high computational effort involved. The RL controller exhibits by far the most versatile and robust control behavior. When operated in the simulation environment, it achieved a high control accuracy. When employed in the real system, however, it only shows average accuracy and a significantly greater performance loss compared to the simulation than the traditional controllers. With MATLAB, it is not yet possible to directly post-train the RL controller on the Raspberry Pi, which is an obstacle to the practical application of RL in a prototyping or teaching setting. Nevertheless, RL in general proves to be a flexible and powerful control method, which is well suited for complex or nonlinear systems where traditional controllers struggle.}, language = {en} } @inproceedings{WiezikHoetterGebhardt2015, author = {Wiezik, P. and H{\"o}tter, Jan-Steffen and Gebhardt, Andreas}, title = {Integration des Laserpolierens in den SLM-Prozess}, series = {DVS Congress 2015, Große Schweißtechnische Tagung, DVS-Studentenkongress, F{\"u}gen von faserverst{\"a}rkten Kunststoffen, Anwendungsnahe Schweißsimulation, Vortr{\"a}ge der Veranstaltungen, N{\"u}rnberg, DE, 15.-17. Sep, 2015}, volume = {315}, booktitle = {DVS Congress 2015, Große Schweißtechnische Tagung, DVS-Studentenkongress, F{\"u}gen von faserverst{\"a}rkten Kunststoffen, Anwendungsnahe Schweißsimulation, Vortr{\"a}ge der Veranstaltungen, N{\"u}rnberg, DE, 15.-17. Sep, 2015}, publisher = {Verl. f{\"u}r Schweißen und verwandte Verfahren, DVS-Verl.}, address = {D{\"u}sseldorf}, isbn = {978-3-945023-46-4}, pages = {117 -- 120}, year = {2015}, language = {de} } @inproceedings{WiesenEngemannLimpertetal.2018, author = {Wiesen, Patrick and Engemann, Heiko and Limpert, Nicolas and Kallweit, Stephan}, title = {Learning by Doing - Mobile Robotics in the FH Aachen ROS Summer School}, series = {European Robotics Forum 2018, TRROS18 Workshop}, booktitle = {European Robotics Forum 2018, TRROS18 Workshop}, pages = {47 -- 58}, year = {2018}, language = {en} } @inproceedings{WiesenSchleser2019, author = {Wiesen, Andreas and Schleser, Markus}, title = {Entwicklung einer Qualit{\"a}tssicherung f{\"u}r das Laserstrahlschweißen im Vakuum mittels Bildverarbeitung}, series = {Große Schweißtechnische Tagung}, booktitle = {Große Schweißtechnische Tagung}, publisher = {DVS-Media}, address = {D{\"u}sseldorf}, isbn = {978-3-96144-066-5}, pages = {1 -- 6}, year = {2019}, language = {de} } @inproceedings{WiegnerVolkerMainzetal.2022, author = {Wiegner, Jonas and Volker, Hanno and Mainz, Fabian and Backes, Andreas and L{\"o}ken, Michael and H{\"u}ning, Felix}, title = {Wiegand-effect-powered wireless IoT sensor node}, series = {Sensoren und Messsysteme 2022}, booktitle = {Sensoren und Messsysteme 2022}, publisher = {VDE Verlag GmbH}, address = {Berlin}, isbn = {978-3-8007-5835-7}, pages = {255 -- 260}, year = {2022}, abstract = {In this article we describe an Internet-of-Things sensing device with a wireless interface which is powered by the oftenoverlooked harvesting method of the Wiegand effect. The sensor can determine position, temperature or other resistively measurable quantities and can transmit the data via an ultra-low power ultra-wideband (UWB) data transmitter. With this approach we can energy-self-sufficiently acquire, process, and wirelessly transmit data in a pulsed operation. A proof-of-concept system was built up to prove the feasibility of the approach. The energy consumption of the system is analyzed and traced back in detail to the individual components, compared to the generated energy and processed to identify further optimization options. Based on the proof-of-concept, an application demonstrator was developed. Finally, we point out possible use cases.}, language = {en} } @inproceedings{Wessling2007, author = {Weßling, Matthias}, title = {Leadership Perspectives: Research Findings, Theories, Practical Experiences}, year = {2007}, abstract = {Leadership Perspectives: Research Findings, Theories, Practical Experiences: Results of Leadership Research and exemplarily application cases show the perspectives and consequences for leadership practice and the following requirements for executives in future.}, subject = {Leadership}, language = {en} } @inproceedings{Wessling2007, author = {Weßling, Matthias}, title = {Motivation and Leadership - The Reiss-Profile of the 16 Basic Desires: Research results and managerial applications}, year = {2007}, abstract = {Recent Results of the scientific Reiss-Profile (16 basic desires) due to the concept of Prof. Dr. Steven Reiss (State University Ohio, U.S.A.), supplemented by the comparative analysis of empirical motivational profiles of european executives of various companies.}, subject = {Motivation}, language = {en} } @inproceedings{Wessling2007, author = {Weßling, Matthias}, title = {Provocative Communication in Coaching and Leadership: scientific research and managerial applications of the Provocative Communication Style}, year = {2007}, abstract = {Concept, scientific research and managerial applications of Provocative Coaching, according to the „Provocative Therapy" of Prof. Dr. Frank Farrelly (University of Wisconsin, U.S.A) in terms of an application of the Provocative Communication Style in specific situations of practical leadership, especially in the role of a coach for their subordinates.}, subject = {Kommunikation}, language = {en} } @inproceedings{Wessling2006, author = {Weßling, Matthias}, title = {Como motivar a si mesmo e aos outros - o valor dos 16 Motivos Vitais para Lideran{\c{c}}a}, year = {2006}, abstract = {O Perfil Reiss apresenta no resultado uma vis{\~a}o da estrutura dos motivos e impulsos de uma pessoa. O ponto de sa{\´i}da para a an{\´a}lise do resultado {\´e} o conhecimento de que os motivos vitais (= valores e metas de sobreviv{\^e}ncia) formam a moldura, na qual as compet{\^e}ncias e capacidades que uma pessoa possui possam se desabrochar de forma ideal. A partir desse princ{\´i}pio, n{\~a}o existe no Perfil Reiss nenhum resultado que se possa classificar como correto ou falso, nem como bom ou mau. Uma compara{\c{c}}{\~a}o entre o resultado do Perfil Reiss e o conte{\´u}do de uma atividade apresentada ou ambicionada d{\´a} informa{\c{c}}{\~a}o sobre at{\´e} que ponto a capacidade de rendimento de uma pessoa nessa posi{\c{c}}{\~a}o pode vir ou vir{\´a} a se desenvolver por um longo tempo.}, subject = {F{\"u}hrung}, language = {es} } @inproceedings{WetterKern2014, author = {Wetter, Martin and Kern, Alexander}, title = {Number of lightning strikes to tall structures - comparison of calculations and measurements using a modern lightning monitoring system}, series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China}, organization = {International Conference on Lightning Protection <2014, Shanghai>}, pages = {1 -- 7}, year = {2014}, language = {en} } @inproceedings{WernerYoshinobuMiyamotoetal.2014, author = {Werner, Frederik and Yoshinobu, T. and Miyamoto, K. and Sch{\"o}ning, Michael Josef and Wagner, Torsten}, title = {Semiconductor-based sensors for imaging of chemical processes}, series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)}, publisher = {VDE-Verl.}, address = {D{\"u}sseldorf}, organization = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, isbn = {978-3-8007-3622-5}, pages = {1 -- 5}, year = {2014}, language = {en} } @inproceedings{WernerMansourRateikeetal.2011, author = {Werner, Frederik and Mansour, Ahmed and Rateike, Franz-Matthias and Schusser, Sebastian and Wagner, Torsten and Yoshinobu, Tatsuo and Keusgen, Michael and Sch{\"o}ning, Michael Josef}, title = {Kompakter Aufbau eines lichtadressierbaren potentiometrischen Sensors mit verfahrbarem Diodenlaser}, series = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43}, booktitle = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43}, editor = {Gerlach, Gerald}, publisher = {TUDpress}, address = {Dresden}, isbn = {978-3-942710-53-4}, pages = {277 -- 280}, year = {2011}, language = {de} } @inproceedings{WellmerChenBraunetal.2007, author = {Wellmer, Georg and Chen, B.-H. and Braun, Carsten and Ballmann, Josef}, title = {Numerical prediction of aeroelastic effects on twin-sting-rig mounted models for rear fuselage and empennage flow investigation in transonic windtunnel}, series = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden}, booktitle = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden}, publisher = {KTH}, address = {Stockholm}, organization = {Confederation of European Aerospace Societies ; American Institute of Aeronautics and Astronautics, Reston, Va. ; Kungliga Tekniska H{\"o}gskolan, Stockholm}, pages = {1 CD-ROM}, year = {2007}, language = {en} } @inproceedings{Wellmann2006, author = {Wellmann, Judith}, title = {Perspektiven eines Bauingenieurs im konstruktiven Ingenieurbau}, year = {2006}, abstract = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 7-12 Die Berufsperspektiven im konstruktiven Ingenieurbau werden trotz sinkendem Bedarf an Statikern positiv bewertet.}, subject = {Ingenieurbau}, language = {de} } @inproceedings{WeldenSeverinsPoghossianetal.2022, author = {Welden, Melanie and Severins, Robin and Poghossian, Arshak and Wege, Christina and Siegert, Petra and Keusgen, Michael and Sch{\"o}ning, Michael Josef}, title = {Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors}, series = {2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN)}, booktitle = {2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN)}, publisher = {IEEE}, isbn = {978-1-6654-5860-3 (Online)}, doi = {10.1109/ISOEN54820.2022.9789657}, pages = {4 Seiten}, year = {2022}, abstract = {A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy.}, language = {en} } @inproceedings{WeissHeslenfeldSaeweetal.2022, author = {Weiss, Christian and Heslenfeld, Jonas and Saewe, Jasmin Kathrin and Bremen, Sebastian and H{\"a}fner, Constantin Leon}, title = {Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF)}, series = {Procedia CIRP}, volume = {111}, booktitle = {Procedia CIRP}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2212-8271}, doi = {10.1016/j.procir.2022.08.102}, pages = {115 -- 120}, year = {2022}, abstract = {In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced.}, language = {en} } @inproceedings{WeissAbanteribaEsch2007, author = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas}, title = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow}, series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B}, booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B}, publisher = {American Society of Mechanical Engineers (ASME)}, address = {New York}, isbn = {0-7918-4288-6}, doi = {10.1115/FEDSM2007-37387}, pages = {1861 -- 1871}, year = {2007}, abstract = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.}, language = {en} } @inproceedings{WeingartSchneiderWollert2009, author = {Weingart, Daniel and Schneider, Ulf and Wollert, J{\"o}rg}, title = {Doppelt gekoppelt - Kabellose und dynamische Anbindung von CANopen an Profinet IO}, series = {Elektrische Automatisierung - Systeme und Komponenten: SPS-IPC-Drives 2009, Fachmesse \& Kongress, 24. - 26. Nov. 2009, N{\"u}rnberg ; [Tagungsband]}, booktitle = {Elektrische Automatisierung - Systeme und Komponenten: SPS-IPC-Drives 2009, Fachmesse \& Kongress, 24. - 26. Nov. 2009, N{\"u}rnberg ; [Tagungsband]}, publisher = {VDE-Verl.}, address = {Berlin [u.a.]}, isbn = {978-3-8007-3184-8}, pages = {147 -- 154}, year = {2009}, language = {de} } @inproceedings{WeilPoghossianSchoeningetal.2012, author = {Weil, M. and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Cherstvy, A.}, title = {Electrical monitoring of layer-by-layer adsorption of oppositely charged macromolecules by means of capacitive field-effect devices}, isbn = {978-3-9813484-2-2}, doi = {10.5162/IMCS2012/P2.5.2}, pages = {1575 -- 1578}, year = {2012}, language = {en} } @inproceedings{WeberTellisDuhovic2016, author = {Weber, Tobias and Tellis, Jane J. and Duhovic, Miro}, title = {Characterization of tool-part-interaction an interlaminar friction for manufacturing process simulation}, series = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016}, booktitle = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016}, isbn = {978-3-00-053387-7}, pages = {1 -- 7}, year = {2016}, language = {en} } @inproceedings{WeberEnglhardHaileretal.2019, author = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph}, title = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling}, series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France}, booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France}, pages = {1 -- 10}, year = {2019}, language = {en} } @inproceedings{WeberEnglhardHaileretal.2015, author = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph}, title = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling}, series = {Proceedings of SAMPE Europe Conference, Amiens , France}, booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France}, pages = {1 -- 10}, year = {2015}, language = {en} } @inproceedings{Weber2015, author = {Weber, Tobias}, title = {Manufacturing Process Simulation for Tooling Optimization: Reduction of Quality Issues During Autoclave Manufacturing of Composite Parts}, series = {Proceedings of SAMPE Europe Conference 2015, Amiens, France}, booktitle = {Proceedings of SAMPE Europe Conference 2015, Amiens, France}, pages = {1 -- 8}, year = {2015}, language = {en} } @inproceedings{WeberTersteggeHallingetal.1995, author = {Weber, S. and Terstegge, Andreas and Halling, H. and Herzog, H. and Reinartz, R. and Reinhart, P. and Rongen, F. and M{\"u}ller-G{\"a}rtner, H.-W.}, title = {The design of an animal PET: flexible geometry for achieving optimal spatial resolution or high sensitivity}, series = {Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2}, booktitle = {Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {Institute of Electrical and Electronics Engineers}, isbn = {078033180X ; 0780331818 ; 0780331826}, pages = {1002 -- 1005}, year = {1995}, language = {en} } @inproceedings{WeberTersteggeEngelsetal.1996, author = {Weber, S. and Terstegge, Andreas and Engels, R. and Herzog, H. and Reinartz, R. and Reinhart, P. and Rongen, F. and M{\"u}ller-G{\"a}rtner, H. W. and Halling, H.}, title = {The KFA TierPET: performance characteristics and measurements}, series = {Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2}, booktitle = {Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {Institute of Electrical and Electronics Engineers}, isbn = {0-7803-3534-1}, issn = {1082-3654}, pages = {1117 -- 1119}, year = {1996}, language = {en} } @inproceedings{WeberWolf2017, author = {Weber, Niklas and Wolf, Martin}, title = {Datenerhebung f{\"u}r die CDG-Forschung}, series = {Prozesse, Technologie, Anwendungen, Systeme und Management 2017 : angewandte Forschung in der Wirtschaftsinformatik : Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg / Arbeitskreis Wirtschaftsinformatik an Fachhochschulen (AKWI)}, booktitle = {Prozesse, Technologie, Anwendungen, Systeme und Management 2017 : angewandte Forschung in der Wirtschaftsinformatik : Tagungsband zur 30. AKWI-Jahrestagung vom 17.09.2017 bis 20.09.2017 an der Hochschule Aschaffenburg / Arbeitskreis Wirtschaftsinformatik an Fachhochschulen (AKWI)}, editor = {Barton, Thomas}, publisher = {mana-Buch}, address = {Heide}, isbn = {978-3-944330-56-3}, pages = {218 -- 227}, year = {2017}, language = {de} } @inproceedings{WeberMarkovicDrumm2007, author = {Weber, Ingo and Markovic, Ivan and Drumm, Christian}, title = {A conceptual framework for composition in business process management}, series = {Business Information Systems : 10th International Conference, BIS 2007, Poznan, Poland, April 25-27, 2007. Proceedings}, booktitle = {Business Information Systems : 10th International Conference, BIS 2007, Poznan, Poland, April 25-27, 2007. Proceedings}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-540-72035-5}, doi = {10.1007/978-3-540-72035-5_5}, pages = {54 -- 66}, year = {2007}, language = {en} } @inproceedings{WeberPorschenDietzeletal.1978, author = {Weber, Hans-Joachim and Porschen, W. and Dietzel, F. and [u.a.],}, title = {In vivo analysis of the influence of combined hyperthermia and gamma irradiation on euoxic and hypoxic tumor cells}, series = {Cancer therapy by hyperthermia and radiation : [proceedings of the 2. International Symposium on Cancer Therapy by Hyperthermia and Radiation, Essen, 2.-4.6.1977]}, booktitle = {Cancer therapy by hyperthermia and radiation : [proceedings of the 2. International Symposium on Cancer Therapy by Hyperthermia and Radiation, Essen, 2.-4.6.1977]}, editor = {Streffer, Christian}, publisher = {Urban and Schwarzenberg}, address = {Baltimore ; Munich [u.a.]}, isbn = {0-8067-1701-7}, pages = {276 -- 277}, year = {1978}, language = {en} } @inproceedings{WarerkarSchmitzGoettscheetal.2009, author = {Warerkar, Shashikant and Schmitz, Stefan and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Reißel, Martin and Tamme, Rainer}, title = {Air-sand heat exchanger for high-temperature storage}, series = {Proceedings of the ASME 3rd International Conference on Energy Sustainability : July 19 - 23, 2009, San Francisco, California, USA. Vol. 2}, booktitle = {Proceedings of the ASME 3rd International Conference on Energy Sustainability : July 19 - 23, 2009, San Francisco, California, USA. Vol. 2}, publisher = {ASME}, address = {New York, NY}, isbn = {978-0-7918-4890-6}, pages = {655 -- 661}, year = {2009}, language = {en} } @inproceedings{WarerkarSchmitzGoettscheetal.2008, author = {Warerkar, S. and Schmitz, S. and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Tamme, R.}, title = {Performance analysis of an air-sand heat exchanger prototype for high-temperature storage}, series = {EuroSun 2008 : 1st International Conference on Solar Heating, Cooling and Buildings ; 7th - 10th October 2008, Lisbon, Portugal : key lectures / ISES, International Solar Energy Society. Vol. 1}, booktitle = {EuroSun 2008 : 1st International Conference on Solar Heating, Cooling and Buildings ; 7th - 10th October 2008, Lisbon, Portugal : key lectures / ISES, International Solar Energy Society. Vol. 1}, publisher = {Sociedade Portuguesa De Energia Solar (SPES)}, address = {Lissabon}, isbn = {978-1-61782-228-5}, pages = {2215 -- 2222}, year = {2008}, language = {en} } @inproceedings{WangMensingGligorevicetal.2008, author = {Wang, W. and Mensing, C. and Gligorevic, Snjezana and Jost, T. and Dammann, A.}, title = {Short term statistical analysis of outdoor to indoor propagation channel for geolocations}, series = {Proceedings of the 13th International OFDM Workshop : (InOWo '08), Aug. 27./28. 2008, Hamburg : Session 3A: Systems concepts}, booktitle = {Proceedings of the 13th International OFDM Workshop : (InOWo '08), Aug. 27./28. 2008, Hamburg : Session 3A: Systems concepts}, organization = {International OFDM Workshop <13, 2008, Hamburg>}, pages = {85 -- 89}, year = {2008}, language = {en} } @inproceedings{WalterElsenMuelleretal.1999, author = {Walter, Peter and Elsen, Ingo and M{\"u}ller, Holger and Kraiss, Karl-Friedrich}, title = {3D object recognition with a specialized mixtures of experts architecture}, series = {IJCNN'99. International Joint Conference on Neural Networks. Proceedings}, booktitle = {IJCNN'99. International Joint Conference on Neural Networks. Proceedings}, publisher = {IEEE}, address = {New York}, isbn = {0-7803-5529-6}, issn = {1098-7576}, doi = {10.1109/IJCNN.1999.836243}, pages = {3563 -- 3568}, year = {1999}, abstract = {Aim of the AXON2 project (Adaptive Expert System for Object Recogniton using Neuml Networks) is the development of an object recognition system (ORS) capable of recognizing isolated 3d objects from arbitrary views. Commonly, classification is based on a single feature extracted from the original image. Here we present an architecture adapted from the Mixtures of Eaqerts algorithm which uses multiple neuml networks to integmte different features. During tmining each neural network specializes in a subset of objects or object views appropriate to the properties of the corresponding feature space. In recognition mode the system dynamically chooses the most relevant features and combines them with maximum eficiency. The remaining less relevant features arz not computed and do therefore not decelerate the-recognition process. Thus, the algorithm is well suited for ml-time applications.}, language = {en} } @inproceedings{WalterGligorevicDetertetal.2010, author = {Walter, Michael and Gligorevic, Snjezana and Detert, Thorben and Schnell, Michael}, title = {UHF/VHF air-to-air propagation measurements}, series = {Proceedings of the Fourth European Conference on Antennas and Propagation (EuCAP) : 12 - 16 April 2010, Barcelona, Spain}, booktitle = {Proceedings of the Fourth European Conference on Antennas and Propagation (EuCAP) : 12 - 16 April 2010, Barcelona, Spain}, organization = {European Association on Antennas and Propagation}, isbn = {978-1-4244-6431-9 ; 978-84-7653-472-4}, pages = {1 -- 5}, year = {2010}, language = {en} } @inproceedings{WallnoeferDrathHuening2015, author = {Walln{\"o}fer, Armin and Drath, Rainer and H{\"u}ning, Felix}, title = {Was ist Funktionales Engineering? Einordnung, Definition, Randbedingungen}, series = {Automation 2015 : 16. Branchentreff der Mess- und Automatisierungstechnik, 11. und 12. Juni 2015, Baden-Baden / VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, booktitle = {Automation 2015 : 16. Branchentreff der Mess- und Automatisierungstechnik, 11. und 12. Juni 2015, Baden-Baden / VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, isbn = {978-3-18-092258-4}, pages = {1 CD-ROM}, year = {2015}, language = {de} } @inproceedings{WalkLaufferRaupachDilgeretal.2004, author = {Walk-Lauffer, Bernd and Raupach, Michael and Dilger, Klaus and B{\"o}hm, Stefan and Mundt, F. and Dilthey, Ulrich and Schleser, Markus}, title = {The interconnection between inner filaments of textile reinforcement by means of polymer modified concrete}, series = {Proceedings of the First International Conference on Innovative Materials and Technologies for Construction and Restoration : : Lecce, June 6 - 9, 2004 / Universit{\`a} degli Studi di Lecce / ed. Antonio La Tegola. Vol. 1: Key-notes, materials, construction}, booktitle = {Proceedings of the First International Conference on Innovative Materials and Technologies for Construction and Restoration : : Lecce, June 6 - 9, 2004 / Universit{\`a} degli Studi di Lecce / ed. Antonio La Tegola. Vol. 1: Key-notes, materials, construction}, publisher = {Liguori}, address = {Napoli}, pages = {150 -- 159}, year = {2004}, language = {en} } @inproceedings{WalentaSchellekensFerreinetal.2017, author = {Walenta, Robert and Schellekens, Twan and Ferrein, Alexander and Schiffer, Stefan}, title = {A decentralised system approach for controlling AGVs with ROS}, series = {AFRICON, Proceedings}, booktitle = {AFRICON, Proceedings}, publisher = {IEEE}, isbn = {978-1-5386-2775-4}, issn = {2153-0033}, doi = {10.1109/AFRCON.2017.8095693}, pages = {1436 -- 1441}, year = {2017}, language = {en} } @inproceedings{WaldmannVeraDachwaldetal.2018, author = {Waldmann, Christoph and Vera, Jean-Pierre de and Dachwald, Bernd and Strasdeit, Henry and Sohl, Frank and Hanff, Hendrik and Kowalski, Julia and Heinen, Dirk and Macht, Sabine and Bestmann, Ulf and Meckel, Sebastian and Hildebrandt, Marc and Funke, Oliver and Gehrt, Jan-J{\"o}ran}, title = {Search for life in ice-covered oceans and lakes beyond Earth}, series = {2018 IEEE/OES Autonomous Underwater Vehicle Workshop, Proceedings November 2018, Article number 8729761}, booktitle = {2018 IEEE/OES Autonomous Underwater Vehicle Workshop, Proceedings November 2018, Article number 8729761}, doi = {10.1109/AUV.2018.8729761}, year = {2018}, abstract = {The quest for life on other planets is closely connected with the search for water in liquid state. Recent discoveries of deep oceans on icy moons like Europa and Enceladus have spurred an intensive discussion about how these waters can be accessed. The challenge of this endeavor lies in the unforeseeable requirements on instrumental characteristics both with respect to the scientific and technical methods. The TRIPLE/nanoAUV initiative is aiming at developing a mission concept for exploring exo-oceans and demonstrating the achievements in an earth-analogue context, exploring the ocean under the ice shield of Antarctica and lakes like Dome-C on the Antarctic continent.}, language = {en} } @inproceedings{WahleZeleny1995, author = {Wahle, Michael and Zeleny, R.}, title = {Berechnung von Elastomer-Bauteilen bei quasistatischer Belastung unter Ber{\"u}cksichtigung von Eigenkontakt und {\"a}ußeren Reibungseinfl{\"u}ssen}, series = {13. CAD-FEM Users' Meeting : FEM-Technologietage, 25. - 27. Oktober 1995 in Bad Wildungen bei Kassel / [Hrsg.: CAD-FEM GmbH]}, booktitle = {13. CAD-FEM Users' Meeting : FEM-Technologietage, 25. - 27. Oktober 1995 in Bad Wildungen bei Kassel / [Hrsg.: CAD-FEM GmbH]}, address = {Grafing b. M{\"u}nchen [u.a.]}, pages = {5 -- 6}, year = {1995}, language = {de} }