@inproceedings{FingerdeVriesVosetal.2020, author = {Finger, Felix and de Vries, Reynard and Vos, Roelof and Braun, Carsten and Bil, Cees}, title = {A comparison of hybrid-electric aircraft sizing methods}, series = {AIAA Scitech 2020 Forum}, booktitle = {AIAA Scitech 2020 Forum}, doi = {10.2514/6.2020-1006}, pages = {31 Seiten}, year = {2020}, abstract = {The number of case studies focusing on hybrid-electric aircraft is steadily increasing, since these configurations are thought to lead to lower operating costs and environmental impact than traditional aircraft. However, due to the lack of reference data of actual hybrid-electric aircraft, in most cases, the design tools and results are difficult to validate. In this paper, two independently developed approaches for hybrid-electric conceptual aircraft design are compared. An existing 19-seat commuter aircraft is selected as the conventional baseline, and both design tools are used to size that aircraft. The aircraft is then re-sized under consideration of hybrid-electric propulsion technology. This is performed for parallel, serial, and fully-electric powertrain architectures. Finally, sensitivity studies are conducted to assess the validity of the basic assumptions and approaches regarding the design of hybrid-electric aircraft. Both methods are found to predict the maximum take-off mass (MTOM) of the reference aircraft with less than 4\% error. The MTOM and payload-range energy efficiency of various (hybrid-) electric configurations are predicted with a maximum difference of approximately 2\% and 5\%, respectively. The results of this study confirm a correct formulation and implementation of the two design methods, and the data obtained can be used by researchers to benchmark and validate their design tools.}, language = {en} } @inproceedings{OegunKlingHeuermannetal.2014, author = {{\"O}gun, Celal Mohan and Kling, Rainer and Heuermann, Holger and Gr{\"a}ser, Ulrich and Schopp, Christoph}, title = {Elektrodenlose quecksilberfreie Niederdrucklampen betrieben mit Mikrowellen}, series = {Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband}, booktitle = {Licht 2014 [Elektronische Ressource] : Den Haag, Holland ; 21. Gemeinschaftstagung, 21. bis 24. September 2014 ; Tagungsband}, publisher = {Nederlandse Stichting voor Verlichtingskunde}, address = {Ede}, pages = {[Elektronische Ressource]}, year = {2014}, language = {de} } @inproceedings{AnthrakidisHerrmannSchornetal.2015, author = {Anthrakidis, Anette and Herrmann, Ulf and Schorn, Christian and Schwarzer, Klemens and Wedding, Philipp}, title = {Weiterentwicklung und Erprobung eines neuartigen Verfahrens zur Bestimmung der Effizienz von konzentrierenden solarthermischen Kollektoren}, series = {25. OTTI Symposium Thermische Solarenergie}, booktitle = {25. OTTI Symposium Thermische Solarenergie}, pages = {15 Seiten}, year = {2015}, language = {de} } @inproceedings{WeldenSeverinsPoghossianetal.2022, author = {Welden, Melanie and Severins, Robin and Poghossian, Arshak and Wege, Christina and Siegert, Petra and Keusgen, Michael and Sch{\"o}ning, Michael Josef}, title = {Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors}, series = {2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN)}, booktitle = {2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN)}, publisher = {IEEE}, isbn = {978-1-6654-5860-3 (Online)}, doi = {10.1109/ISOEN54820.2022.9789657}, pages = {4 Seiten}, year = {2022}, abstract = {A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy.}, language = {en} } @inproceedings{PoghossianBronderSchejaetal.2016, author = {Poghossian, Arshak and Bronder, Thomas and Scheja, S. and Wu, Chunsheng and Metzger-Boddien, C. and Keusgen, M. and Sch{\"o}ning, Michael Josef}, title = {Label-free Electrostatic Detection of DNA Amplification by PCR Using Capacitive Field-effect Devices}, series = {Procedia Engineering}, volume = {Vol. 168}, booktitle = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2016.11.512}, pages = {514 -- 517}, year = {2016}, abstract = {A capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensor modified with a positively charged weak polyelectrolyte of poly(allylamine hydrochloride) (PAH)/single-stranded probe DNA (ssDNA) bilayer has been used for a label-free electrostatic detection of pathogen-specific DNA amplification via polymerase chain reaction (PCR). The sensor is able to distinguish between positive and negative PCR solutions, to detect the existence of target DNA amplicons in PCR samples and thus, can be used as tool for a quick verification of DNA amplification and the successful PCR process.}, language = {en} } @inproceedings{ThenentDahmann2011, author = {Thenent, N. E. and Dahmann, Peter}, title = {Increasing aircraft design flexibility - The development of a hydrostatic transmission for gliders with self-launching capability}, series = {Deutscher Luft- und Raumfahrtkongress 2011 : Bremen, 27. bis 29. September 2011 ; Tagungsband}, booktitle = {Deutscher Luft- und Raumfahrtkongress 2011 : Bremen, 27. bis 29. September 2011 ; Tagungsband}, publisher = {Dt. Gesellschaft f{\"u}r Luft- und Raumfahrt}, address = {Bonn}, isbn = {978-3-9321-8274-7}, pages = {865 -- 883}, year = {2011}, language = {en} } @inproceedings{StaatSzelinskiHeitzer2001, author = {Staat, Manfred and Szelinski, E. and Heitzer, Michael}, title = {Kollapsanalyse von l{\"a}ngsfehlerbehafteten Rohren und Beh{\"a}ltern}, year = {2001}, abstract = {Es werden verbesserte Kollapsanalysen von dickwandigen, mit axialen Oberfl{\"a}chenfehlern behafteten Rohren und Beh{\"a}ltern vorgeschlagen.}, subject = {Druckbeh{\"a}lter}, language = {de} } @inproceedings{LeichtScholtenSteuerDankertBouffier2016, author = {Leicht-Scholten, Carmen and Steuer-Dankert, Linda and Bouffier, Anna}, title = {Facing Future Challenges: Building Engineers for Tomorrow}, series = {Conference proceedings : new perspectives in science education : 5th Conference edition, Florence, Italy, 17-18 March 2016}, booktitle = {Conference proceedings : new perspectives in science education : 5th Conference edition, Florence, Italy, 17-18 March 2016}, isbn = {978-886292-705-5}, pages = {32 -- 37}, year = {2016}, abstract = {Future engineers are increasingly confronted with the so-called Megatrends which are the big social challenges society has to cope with. These Megatrends, such as "Silver Society", "Globalization", "Mobility" and "Female Shift" require an application-oriented perspective on Diversity especially in the engineering field. Therefore, it is necessary to enable future engineers not only to look at the technical perspectives of a problem, but also to be able to see the related questions within societies they are developing their artefacts for. The aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. Bringing together technical knowledge and social competences which go beyond a mere training of the so-called "soft skills", is a new approach followed at RWTH Aachen University, one of the leading technical universities in Germany. RWTH Aachen University has established the bridging professorship "Gender and Diversity in Engineering" (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. In the frame of a sustainable teaching concept the research group under the leadership of Prof. Carmen Leicht-Scholten has developed an approach which imparts a supplication-specific Gender and Diversity expertise to engineers. In workshops students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge in their special field of study and later work. To substantiate this, the course participants have to solve case studies from real life. The cases which are developed in collaboration with non-profit organizations and enterprises from economy rise the students to challenges which are inspired by professional life. Evaluation shows the success of this approach as well as an increasing demand for such teaching formats.}, language = {en} } @inproceedings{FingerGoettenBraun2018, author = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten}, title = {Initial Sizing for a Family of Hybrid-Electric VTOL General Aviation Aircraft}, series = {67. Deutscher Luft- und Raumfahrtkongress 2018}, booktitle = {67. Deutscher Luft- und Raumfahrtkongress 2018}, pages = {14 S.}, year = {2018}, language = {en} } @inproceedings{Ritz2001, author = {Ritz, Thomas}, title = {Produktion von kundenindividuellen Informationsdienstleistungen}, series = {Workshop Internetbasierte Vertriebsunterst{\"u}tzung in der Praxis : 26. April 2001, Institutszentrum Stuttgart der Fraunhofer-Gesellschaft (IZS) / Fraunhofer Institut Arbeitswirtschaft und Organisation}, booktitle = {Workshop Internetbasierte Vertriebsunterst{\"u}tzung in der Praxis : 26. April 2001, Institutszentrum Stuttgart der Fraunhofer-Gesellschaft (IZS) / Fraunhofer Institut Arbeitswirtschaft und Organisation}, editor = {Zabel, Armin}, publisher = {Fraunhofer IAO}, address = {Stuttgart}, pages = {4 S.}, year = {2001}, language = {de} } @inproceedings{JungStaatMueller2014, author = {Jung, Alexander and Staat, Manfred and M{\"u}ller, Wolfram}, title = {Optimization of the flight style in ski jumping}, series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona}, booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20 - 25, 2014, Barcelona}, editor = {Onate, E.}, organization = {World Congress on Computational Mechanics <11, 2014, Barcelona>}, pages = {799 -- 810}, year = {2014}, language = {en} } @inproceedings{DigelDachwaldArtmannetal.2009, author = {Digel, Ilya and Dachwald, Bernd and Artmann, Gerhard and Linder, Peter and Funke, O.}, title = {A concept of a probe for particle analysis and life detection in icy environments}, year = {2009}, abstract = {A melting probe equipped with autofluorescence-based detection system combined with a light scattering unit, and, optionally, with a microarray chip would be ideally suited to probe icy environments like Europa's ice layer as well as the polar ice layers of Earth and Mars for recent and extinct live.}, subject = {Sonde}, language = {en} } @inproceedings{AlexopoulosHoffschmidtRauetal.2009, author = {Alexopoulos, Spiros and Hoffschmidt, Bernhard and Rau, Christoph and Schwarzb{\"o}zl, Peter}, title = {Simulation results for a hybridization concept of a small solar tower power plant}, series = {SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings}, booktitle = {SolarPACES 2009 : electricity, fuels and clean water powered by the sun ; 15 - 18 September 2009, Berlin, Germany ; the 15th SolarPACES conference ; proceedings}, publisher = {Deutsches Zentrum f. Luft- u. Raumfahrt}, address = {Stuttgart}, isbn = {9783000287558}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @inproceedings{TranStaat2012, author = {Tran, Thanh Ngoc and Staat, Manfred}, title = {A primal-dual shakedown analysis of 3D structures using the face-based smoothed finite element method}, series = {Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012)}, booktitle = {Proceedings European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS 2012)}, editor = {Eberhardsteiner, J.}, year = {2012}, language = {en} } @inproceedings{SchulteEggert2021, author = {Schulte, Maximilian and Eggert, Mathias}, title = {Predicting hourly bitcoin prices based on long short-term memory neural networks}, series = {Proceedings of the International Conference on Wirtschaftsinformatik (WI) 2021}, booktitle = {Proceedings of the International Conference on Wirtschaftsinformatik (WI) 2021}, pages = {16 Seiten}, year = {2021}, abstract = {Bitcoin is a cryptocurrency and is considered a high-risk asset class whose price changes are difficult to predict. Current research focusses on daily price movements with a limited number of predictors. The paper at hand aims at identifying measurable indicators for Bitcoin price movements and the development of a suitable forecasting model for hourly changes. The paper provides three research contributions. First, a set of significant indicators for predicting the Bitcoin price is identified. Second, the results of a trained Long Short-term Memory (LSTM) neural network that predicts price changes on an hourly basis is presented and compared with other algorithms. Third, the results foster discussions of the applicability of neural nets for stock price predictions. In total, 47 input features for a period of over 10 months could be retrieved to train a neural net that predicts the Bitcoin price movements with an error rate of 3.52 \%.}, language = {en} } @inproceedings{FerreinSchifferKallweit2018, author = {Ferrein, Alexander and Schiffer, Stefan and Kallweit, Stephan}, title = {The ROSIN Education Concept - Fostering ROS Industrial-Related Robotics Education in Europe}, series = {ROBOT 2017: Third Iberian Robotics Conference}, booktitle = {ROBOT 2017: Third Iberian Robotics Conference}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-70836-2}, doi = {10.1007/978-3-319-70836-2_31}, pages = {370 -- 381}, year = {2018}, language = {en} } @inproceedings{FrotscherRaatschenStaat2012, author = {Frotscher, Ralf and Raatschen, Hans-J{\"u}rgen and Staat, Manfred}, title = {Effectiveness of the edge-based smoothed finite element method applied to soft biological tissues}, series = {ESMC-2012 - 8th European Solid Mechanics Conference, Graz, Austria, July 9-13, 2012}, booktitle = {ESMC-2012 - 8th European Solid Mechanics Conference, Graz, Austria, July 9-13, 2012}, editor = {Holzapfel, Gerhard A.}, publisher = {Verlag d. Technischen Universit{\"a}t Graz}, address = {Graz}, isbn = {978-3-85125-223-1}, year = {2012}, language = {en} } @inproceedings{RekePeterSchulteTiggesetal.2020, author = {Reke, Michael and Peter, Daniel and Schulte-Tigges, Joschua and Schiffer, Stefan and Ferrein, Alexander and Walter, Thomas and Matheis, Dominik}, title = {A Self-Driving Car Architecture in ROS2}, series = {2020 International SAUPEC/RobMech/PRASA Conference, Cape Town, South Africa}, booktitle = {2020 International SAUPEC/RobMech/PRASA Conference, Cape Town, South Africa}, publisher = {IEEE}, address = {New York, NY}, isbn = {978-1-7281-4162-6}, doi = {10.1109/SAUPEC/RobMech/PRASA48453.2020.9041020}, pages = {1 -- 6}, year = {2020}, abstract = {In this paper we report on an architecture for a self-driving car that is based on ROS2. Self-driving cars have to take decisions based on their sensory input in real-time, providing high reliability with a strong demand in functional safety. In principle, self-driving cars are robots. However, typical robot software, in general, and the previous version of the Robot Operating System (ROS), in particular, does not always meet these requirements. With the successor ROS2 the situation has changed and it might be considered as a solution for automated and autonomous driving. Existing robotic software based on ROS was not ready for safety critical applications like self-driving cars. We propose an architecture for using ROS2 for a self-driving car that enables safe and reliable real-time behaviour, but keeping the advantages of ROS such as a distributed architecture and standardised message types. First experiments with an automated real passenger car at lower and higher speed-levels show that our approach seems feasible for autonomous driving under the necessary real-time conditions.}, language = {en} } @inproceedings{TranTranMatthiesetal.2016, author = {Tran, Ngoc Trinh and Tran, Thanh Ngoc and Matthies, Hermann G. and Stavroulakis, Georgios Eleftherios and Staat, Manfred}, title = {FEM Shakedown of uncertain structures by chance constrained programming}, series = {PAMM Proceedings in Applied Mathematics and Mechanics}, volume = {16}, booktitle = {PAMM Proceedings in Applied Mathematics and Mechanics}, number = {1}, issn = {1617-7061}, doi = {10.1002/pamm.201610346}, pages = {715 -- 716}, year = {2016}, language = {en} } @inproceedings{ArtmannDigelLinderetal.2011, author = {Artmann, Gerhard and Digel, Ilya and Linder, Peter and Temiz Artmann, Ayseg{\"u}l}, title = {Biophysical and Engineering Contributions to Plant Research}, year = {2011}, abstract = {Tests with palm tree leaves have just started yet and scan data are in the process to be analyzed. The final goal of future project for palm tree gender and species recognition will be to develop optical scanning technology to be applied to date palm tree leaves for in-situ screening purposes. Depending on the software used and the particular requirements of the users the technology potentially shall be able to identify palm tree diseases, palm tree gender, and species of young date palm trees by scanning leaves.}, subject = {Pflanzenphysiologie}, language = {en} } @inproceedings{MolinnusHardtKaeveretal.2017, author = {Molinnus, Denise and Hardt, Gabriel and K{\"a}ver, Larissa and Willenberg, Holger S. and Poghossian, Arshak and Keusgen, Michael and Sch{\"o}ning, Michael Josef}, title = {Detection of Adrenaline Based on Bioelectrocatalytical System to Support Tumor Diagnostic Technology}, series = {MDPI Proceedings}, booktitle = {MDPI Proceedings}, doi = {10.3390/proceedings1040506}, pages = {4 Seiten}, year = {2017}, language = {en} } @inproceedings{StaatDuong2016, author = {Staat, Manfred and Duong, Minh Tuan}, title = {Smoothed Finite Element Methods for Nonlinear Solid Mechanics Problems: 2D and 3D Case Studies}, series = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2}, booktitle = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2}, pages = {440 -- 445}, year = {2016}, abstract = {The Smoothed Finite Element Method (SFEM) is presented as an edge-based and a facebased techniques for 2D and 3D boundary value problems, respectively. SFEMs avoid shortcomings of the standard Finite Element Method (FEM) with lower order elements such as overly stiff behavior, poor stress solution, and locking effects. Based on the idea of averaging spatially the standard strain field of the FEM over so-called smoothing domains SFEM calculates the stiffness matrix for the same number of degrees of freedom (DOFs) as those of the FEM. However, the SFEMs significantly improve accuracy and convergence even for distorted meshes and/or nearly incompressible materials. Numerical results of the SFEMs for a cardiac tissue membrane (thin plate inflation) and an artery (tension of 3D tube) show clearly their advantageous properties in improving accuracy particularly for the distorted meshes and avoiding shear locking effects.}, language = {en} } @inproceedings{PlatenPoghossianSchoening2006, author = {Platen, J. and Poghossian, Arshak and Sch{\"o}ning, Michael Josef}, title = {Pr{\"a}paration von selbstjustierenden Nanostrukturen mittels Schichtausdehnungstechnik}, series = {Sensoren und Mess-Systeme 2006 : Vortr{\"a}ge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau}, booktitle = {Sensoren und Mess-Systeme 2006 : Vortr{\"a}ge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau}, publisher = {VDE Verl.}, address = {Berlin}, isbn = {3-8007-2939-3}, pages = {277 -- 280}, year = {2006}, language = {de} } @inproceedings{AltherrConzenElsenetal.2023, author = {Altherr, Lena and Conzen, Max and Elsen, Ingo and Frauenrath, Tobias and Lyrmann, Andreas}, title = {Sensor retrofitting of existing buildings in an interdisciplinary teaching project at university level}, series = {Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel}, booktitle = {Tagungsband AALE 2023 : mit Automatisierung gegen den Klimawandel}, editor = {Reiff-Stephan, J{\"o}rg and J{\"a}kel, Jens and Schwarz, Andr{\´e}}, publisher = {le-tex publishing services GmbH}, address = {Leipzig}, isbn = {978-3-910103-01-6}, doi = {10.33968/2023.04}, pages = {31 -- 40}, year = {2023}, abstract = {Existing residential buildings have an average lifetime of 100 years. Many of these buildings will exist for at least another 50 years. To increase the efficiency of these buildings while keeping costs at reasonable rates, they can be retrofitted with sensors that deliver information to central control units for heating, ventilation and electricity. This retrofitting process should happen with minimal intervention into existing infrastructure and requires new approaches for sensor design and data transmission. At FH Aachen University of Applied Sciences, students of different disciplines work together to learn how to design, build, deploy and operate such sensors. The presented teaching project already created a low power design for a combined CO2, temperature and humidity measurement device that can be easily integrated into most home automation systems}, language = {en} } @inproceedings{ValeroBung2016, author = {Valero, Daniel and Bung, Daniel Bernhard}, title = {Interfacial velocity estimation in highly aerated stepped spillway flows with a single tip fibre optical probe and Artificial Neural Networks}, series = {6th IAHR International Junior Researcher and Engineer Workshop on Hydraulic Structures, May 30th to June 1st 2016. L{\"u}beck, Germany}, booktitle = {6th IAHR International Junior Researcher and Engineer Workshop on Hydraulic Structures, May 30th to June 1st 2016. L{\"u}beck, Germany}, doi = {10.15142/T3Q590}, pages = {13 Seiten}, year = {2016}, abstract = {Air-water flows can be found in different engineering applications: from nuclear engineering to huge hydraulic structures. In this paper, a single tip fibre optical probe has been used to record high frequency (over 1 MHz) phase functions at different locations of a stepped spillway. These phase functions have been related to the interfacial velocities by means of Artificial Neural Networks (ANN) and the measurements of a classical double tip conductivity probe. Special attention has been put to the input selection and the ANN dimensions. Finally, ANN have shown to be able to link the signal rising times and plateau shapes to the air-water interfacial velocity.}, language = {en} } @inproceedings{SchulteSchwagerNoureldinetal.2023, author = {Schulte, Jonas and Schwager, Christian and Noureldin, Kareem and May, Martin and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf}, title = {Gradient controlled startup procedure of a molten-salt power-to-heat energy storage plant based on dynamic process simulation}, series = {SolarPACES: Solar Power \& Chemical Energy Systems}, booktitle = {SolarPACES: Solar Power \& Chemical Energy Systems}, number = {2815 / 1}, publisher = {AIP conference proceedings / American Institute of Physics}, address = {Melville, NY}, isbn = {978-0-7354-4623-6}, issn = {1551-7616 (online)}, doi = {10.1063/5.0148741}, pages = {9 Seiten}, year = {2023}, abstract = {The integration of high temperature thermal energy storages into existing conventional power plants can help to reduce the CO2 emissions of those plants and lead to lower capital expenditures for building energy storage systems, due to the use of synergy effects [1]. One possibility to implement that, is a molten salt storage system with a powerful power-to-heat unit. This paper presents two possible control concepts for the startup of the charging system of such a facility. The procedures are implemented in a detailed dynamic process model. The performance and safety regarding the film temperatures at heat transmitting surfaces are investigated in the process simulations. To improve the accuracy in predicting the film temperatures, CFD simulations of the electrical heater are carried out and the results are merged with the dynamic model. The results show that both investigated control concepts are safe regarding the temperature limits. The gradient controlled startup performed better than the temperature-controlled startup. Nevertheless, there are several uncertainties that need to be investigated further.}, language = {en} } @inproceedings{OetringerDuemmlerGoettsche2020, author = {Oetringer, Kerstin and D{\"u}mmler, Andreas and G{\"o}ttsche, Joachim}, title = {Neues Modell zur 1D-Simulation der indirekten Verdunstungsk{\"u}hlung}, series = {DKV-Tagung 2020, AA II.1}, booktitle = {DKV-Tagung 2020, AA II.1}, pages = {250 -- 262}, year = {2020}, abstract = {Im Projekt Coolplan- AIR geht es um die Fortentwicklung und Feld- Validierung eines Berechnungs- und Auslegungstools zur energieeffizienten K{\"u}hlung von Geb{\"a}uden mit luftgest{\"u}tzten Systemen. Neben dem Aufbau und der Weiterentwicklung von Simulationsmodellen erfolgen Vermessungen der Gesamtsysteme anhand von Praxisanlagen im Feld. Eine der betrachteten Anlagen arbeitet mit indirekter Verdunstung. Diese Ver{\"o}ffentlichung zeigt den Entwicklungsprozess und den Aufbau des Simulationsmodells zur Verdunstungsk{\"u}hlung in der Simulationsumgebung Matlab- Simulink mit der CARNOT- Toolbox. Das besondere Augenmerk liegt dabei auf dem physikalischen Modell des W{\"a}rme{\"u}bertragers, in dem die Verdunstung implementiert ist. Dem neuen Modellansatz liegt die Annahme einer aus der Enthalpie- Betrachtung hergeleiteten effektiven W{\"a}rmekapazit{\"a}t zugrunde. Des Weiteren wird der Befeuchtungsgrad als konstant angesehen und eine standardisierte Zunahme der W{\"a}rme{\"u}bertragung des feuchten gegen{\"u}ber dem trockenen W{\"a}rme{\"u}bertrager angenommen. Die Validierung des Modells erfolgte anhand von Literaturdaten. F{\"u}r den trockenen W{\"a}rmetauscher ist der maximale absolute Fehler der berechneten Austrittstemperatur (Zuluft) kleiner als ±0.1 K und f{\"u}r den nassen W{\"a}rmetauscher (K{\"u}hlfall) unter der Annahme eines konstanten Verdunstungsgrades kleiner als ±0.4 K.}, language = {de} } @inproceedings{KnackstedtEggertFleischer2012, author = {Knackstedt, Ralf and Eggert, Mathias and Fleischer, Stefan}, title = {The Legal Perspective on Business to Government Reporting - A Conceptual Modeling Approach and Its Application in the Financial Sector}, series = {45th Hawaii International Conference on System Sciences 2012}, booktitle = {45th Hawaii International Conference on System Sciences 2012}, isbn = {978-0-7695-4525-7}, doi = {10.1109/HICSS.2012.576}, pages = {2309 -- 2318}, year = {2012}, language = {en} } @inproceedings{FrotscherStaat2015, author = {Frotscher, Ralf and Staat, Manfred}, title = {An electromechanical model for cardiac tissue constructs}, series = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon}, booktitle = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon}, publisher = {RWTH Aachen University}, address = {Aachen}, organization = {ECCOMAS Young Investigators Conference <3, 2015, Aachen>}, pages = {1 -- 4}, year = {2015}, language = {en} } @inproceedings{RendonDieckmannWeidleetal.2018, author = {Rendon, Carlos and Dieckmann, Simon and Weidle, Mathias and Dersch, J{\"u}rgen and Teixeira Boura, Cristiano Jos{\´e} and Polklas, Thomas and Kuschel, Marcus and Herrmann, Ulf}, title = {Retrofitting of existing parabolic trough collector power plants with molten salt tower systems}, series = {AIP Conference Proceedings}, volume = {2033}, booktitle = {AIP Conference Proceedings}, number = {1}, doi = {10.1063/1.5067030}, pages = {030014-1 -- 030014-8}, year = {2018}, language = {en} } @inproceedings{ValeroKramerBungetal.2019, author = {Valero, Daniel and Kramer, Matthias and Bung, Daniel Bernhard and Chanson, Hubert}, title = {A stochastic bubble generator for air-water flow research}, series = {E-proceedings of the 38th IAHR World Congress, September 1-6, 2019, Panama City, Panama}, booktitle = {E-proceedings of the 38th IAHR World Congress, September 1-6, 2019, Panama City, Panama}, doi = {10.3850/38WC092019-0909}, pages = {5714 -- 5721}, year = {2019}, language = {en} } @inproceedings{BeckerEggertFleischeretal.2013, author = {Becker, J{\"o}rg and Eggert, Mathias and Fleischer, Stefan and Knackstedt, Ralf}, title = {How to Teach Regulatory Compliant Data Warehouse Engineering?}, series = {Proceedings of the Nineteenth Americas Conference on Information Systems, Chicago, Illinois, August 15-17, 2013.}, booktitle = {Proceedings of the Nineteenth Americas Conference on Information Systems, Chicago, Illinois, August 15-17, 2013.}, pages = {10 S.}, year = {2013}, language = {en} } @inproceedings{KerpenBungSchlurmann2010, author = {Kerpen, N. B. and Bung, Daniel Bernhard and Schlurmann, Torsten}, title = {Physical model investigations of ships passing through a lock}, series = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010}, booktitle = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010}, editor = {Janssen, Robert}, publisher = {School of Civil Engineeering, The University of Queensland}, address = {Brisbane}, organization = {International Junior Researcher and Engineer Workshop on Hydraulic Structures <3, 2010, Edinburgh>}, isbn = {9781742720159}, pages = {93 -- 100}, year = {2010}, language = {en} } @inproceedings{Bung2011, author = {Bung, Daniel Bernhard}, title = {Non-intrusive measuring of air-water flow properties in self-aerated stepped spillway flow}, series = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia}, booktitle = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia}, organization = {International Association for Hydraulic Engineering and Research}, isbn = {978-0-85825-868-6}, pages = {2380 -- 2387}, year = {2011}, language = {en} } @inproceedings{BungSchlenkhoff2008, author = {Bung, Daniel Bernhard and Schlenkhoff, Andreas}, title = {Optimization of the reaeration potential on embankment stepped spillways in skimming flow regime}, series = {Hydraulic structures : proceedings of the second International Junior Researcher and Engineer Workshop on Hydraulic Structures, Pisa, Italy, 30 July-1 August 2008}, booktitle = {Hydraulic structures : proceedings of the second International Junior Researcher and Engineer Workshop on Hydraulic Structures, Pisa, Italy, 30 July-1 August 2008}, editor = {Pagliara, Stefano}, organization = {International Junior Researcher and Engineer Workshop on Hydraulic Structures <2, 2008, Pisa>}, isbn = {978-88-8492-568-8}, pages = {97 -- 106}, year = {2008}, language = {en} } @inproceedings{KerpenVerwornBungetal.2011, author = {Kerpen, N. and Verworn, F. and Bung, Daniel Bernhard and Daemrich, K.-F. and Schlurmann, Torsten}, title = {Ermittlung von Wellen{\"u}berlaufmengen an Sturmflutschutzw{\"a}nden auf Deichen}, series = {Maritimer Wasserbau und K{\"u}steningenieurwesen : 8. FZK-Kolloquium : Hannover 10. M{\"a}rz, 2011}, booktitle = {Maritimer Wasserbau und K{\"u}steningenieurwesen : 8. FZK-Kolloquium : Hannover 10. M{\"a}rz, 2011}, organization = {Forschungszentrum K{\"u}ste (FZK)}, issn = {1610-5249}, pages = {63 -- 68}, year = {2011}, language = {de} } @inproceedings{SchlenkhoffBung2009, author = {Schlenkhoff, Andreas and Bung, Daniel Bernhard}, title = {Prediction of oxygen transfer in self-aerated skimming flow on embankment stepped spillways}, series = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, booktitle = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, organization = {International Association for Hydraulic Engineering and Research}, isbn = {9789078046080}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @inproceedings{BungSchlenkhoffOertel2009, author = {Bung, Daniel Bernhard and Schlenkhoff, Andreas and Oertel, M.}, title = {Self-aerated skimming flow on embankment stepped spillways}, series = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, booktitle = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, organization = {International Association for Hydraulic Engineering and Research}, isbn = {9789078046080}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @inproceedings{BungSchlenkhoff2010, author = {Bung, Daniel Bernhard and Schlenkhoff, Andreas}, title = {Selbstbel{\"u}ftete Gerinnestr{\"o}mungen auf Treppenschussrinnen}, series = {Talsperren im Wandel : 15. Deutsches Talsperrensymposium ; Beitr{\"a}ge zur Tagung am 14. bis 16. April 2010 im Eurogress Aachen}, booktitle = {Talsperren im Wandel : 15. Deutsches Talsperrensymposium ; Beitr{\"a}ge zur Tagung am 14. bis 16. April 2010 im Eurogress Aachen}, organization = {Deutsches TalsperrenKomitee}, isbn = {978-3-8322-9043-6}, pages = {39 -- 47}, year = {2010}, language = {de} } @inproceedings{OertelBungSchlenkhoff2009, author = {Oertel, M. and Bung, Daniel Bernhard and Schlenkhoff, Andreas}, title = {Flash flood awareness and prevention}, series = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, booktitle = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, organization = {International Association for Hydraulic Engineering and Research}, isbn = {9789078046080}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @inproceedings{Golland2019, author = {Golland, Alexander}, title = {Datenschutzregulierung als Eingriff in Wertsch{\"o}pfungsmodelle}, series = {Die Zukunft der Daten{\"o}konomie : zwischen Gesch{\"a}ftsmodell, Kollektivgut und Verbraucherschutz}, booktitle = {Die Zukunft der Daten{\"o}konomie : zwischen Gesch{\"a}ftsmodell, Kollektivgut und Verbraucherschutz}, editor = {Ochs, Carsten and Friedewald, Michael and Hess, Thomas and Lamla, J{\"o}rn}, publisher = {Springer Fachmedien}, address = {Wiesbaden}, isbn = {978-3-658-27510-5}, pages = {45 -- 68}, year = {2019}, abstract = {Das Kopplungsverbot verbietet, die Nutzung einer Dienstleistung von der Erteilung einer nicht f{\"u}r die Leistungserbringung erforderlichen Einwilligung abh{\"a}ngig zu machen. Personalisierte Werbung wird hierdurch erheblich erschwert. Anbieter k{\"o}nnen jedoch durch Bereitstellung eines alternativen, einwilligungsfreien Zugangs zu derselben Leistung ihren Dienst datenschutzkonform anbieten. Ein solcher Zugang muss nicht zwingend in Form eines fixen Entgelts gestaltet sein. Vielmehr ist es datenschutzrechtlich in gewissem Umfang zul{\"a}ssig, Preise unter Einbeziehung personenbezogener Daten dynamisch zu gestalten.}, language = {de} } @inproceedings{WulfhorstMerseburgTippkoetter2015, author = {Wulfhorst, Helene and Merseburg, Johannes and Tippk{\"o}tter, Nils}, title = {Analyse von Lignocellulose mittels dynamischer Differenzkalorimetrie und Infrarot - Spektrometrie}, series = {12. Dresdner Sensor-Symposium 2015 2015-12-07 - 2015-12-09}, booktitle = {12. Dresdner Sensor-Symposium 2015 2015-12-07 - 2015-12-09}, isbn = {978-3-9813484-9-1}, doi = {10.5162/12dss2015/P6.2}, pages = {210 -- 215}, year = {2015}, language = {de} } @inproceedings{SteuerDankertBergLeichtScholten2015, author = {Steuer-Dankert, Linda and Berg, Tobias and Leicht-Scholten, Carmen}, title = {Breaking the habit - new approaches in engineering education}, series = {Proceedings of the 43rd Annual Conference of the European Society for Engineering Education}, booktitle = {Proceedings of the 43rd Annual Conference of the European Society for Engineering Education}, isbn = {978-2-87352-012-0}, pages = {11}, year = {2015}, abstract = {Within the framework of the project a genderand diversity-oriented teaching evaluation and modern, media-supported blended learning approaches were used in order to achieve the intended goals. First research results of the literature and status quo analysis were already implemented and tested in newly designed teaching approaches, for example in a multidisciplinary introductory lecture of civil engineering at RWTH Aachen University.}, language = {en} } @inproceedings{NiemuellerNeumannHenkeetal.2017, author = {Niemueller, Tim and Neumann, Tobias and Henke, Christoph and Sch{\"o}nitz, Sebastian and Reuter, Sebastian and Ferrein, Alexander and Jeschke, Sabina and Lakemeyer, Gerhard}, title = {International Harting Open Source Award 2016: Fawkes for the RoboCup Logistics League}, series = {RoboCup 2016: RoboCup 2016: Robot World Cup XX. RoboCup 2016}, booktitle = {RoboCup 2016: RoboCup 2016: Robot World Cup XX. RoboCup 2016}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-68792-6}, doi = {10.1007/978-3-319-68792-6_53}, pages = {634 -- 642}, year = {2017}, language = {en} } @inproceedings{AchenbachGeimerGoettscheetal.2011, author = {Achenbach, Timm and Geimer, K. and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Lynen, A. and Bauer, J.}, title = {Simulation and flow measurements of volumetric high temperature absorbers for solar tower power plants}, series = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, booktitle = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, address = {Granada}, pages = {1 CD-ROM}, year = {2011}, language = {en} } @inproceedings{TeixeiraBouraEcksteinFelinksetal.2011, author = {Teixeira Boura, Cristiano Jos{\´e} and Eckstein, J. and Felinks, J. and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Schmitz, S.}, title = {3-D CFD simulation of an air-sand heat exchanger}, series = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, booktitle = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, address = {Granada}, pages = {1 CD-ROM}, year = {2011}, language = {en} } @inproceedings{AchenbachGoettscheKaufholdetal.2011, author = {Achenbach, Timm and G{\"o}ttsche, Joachim and Kaufhold, O. and Hoffschmidt, Bernhard}, title = {Development of an edge module for open volumetric receiver for the use of the radiation at the receiver boundary region}, series = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, booktitle = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, address = {Granada}, pages = {1 CD-ROM}, year = {2011}, language = {en} } @inproceedings{AlexopoulosHoffschmidtRau2011, author = {Alexopoulos, Spiros and Hoffschmidt, Bernhard and Rau, Christoph}, title = {Comparison of steady-state and transient simulations for solar tower power plants with open-volumetric receiver}, series = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, booktitle = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain}, address = {Granada}, pages = {1 CD-ROM}, year = {2011}, language = {en} } @inproceedings{AlexopoulosRauSattleretal.2011, author = {Alexopoulos, Spiros and Rau, Christoph and Sattler, Johannes Christoph and Kronhardt, Valentina and Hoffschmidt, Bernhard}, title = {Simulation von Solarturmkraftwerken mit offenem volumetrischen Receiver am Standort Italien}, series = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster}, booktitle = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster}, publisher = {DLR}, address = {K{\"o}ln}, pages = {4 S.}, year = {2011}, language = {de} } @inproceedings{AlexopoulosHoffschmidtRauetal.2010, author = {Alexopoulos, Spiros and Hoffschmidt, Bernhard and Rau, Christoph and Schmitz, M. and Schwarzb{\"o}zl, P. and Pomp, Stefan}, title = {Simulation results for a hybridized operation of a gas turbine or a burner for a small solar tower power plant}, series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France}, booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France}, publisher = {Soc. OSC}, address = {Saint Maur}, pages = {82 -- 83}, year = {2010}, language = {en} } @inproceedings{ZiolkoSchmitzSattleretal.2010, author = {Ziolko, C. and Schmitz, M. and Sattler, Johannes Christoph and Khedim, Ahmed and Hoffschmidt, Bernhard}, title = {AlSol - the open volumetric receiver technology moves to Africa}, series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France}, booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France}, publisher = {Soc. OSC}, address = {Saint Maur}, pages = {93 -- 94}, year = {2010}, language = {en} } @inproceedings{AlexopoulosRauHoffschmidtetal.2012, author = {Alexopoulos, Spiros and Rau, Christoph and Hoffschmidt, Bernhard and Breitbach, Gerd and Latzke, Markus}, title = {Modelling and validation of a transient heat recovery steam generator of the solar tower power plant Juelich}, series = {Eurosun 2012 : Solar energy for a brighter future : conference proceedings : Rijeka, 18.-22.09.2012}, booktitle = {Eurosun 2012 : Solar energy for a brighter future : conference proceedings : Rijeka, 18.-22.09.2012}, address = {Rijeka}, pages = {ID 97}, year = {2012}, language = {en} } @inproceedings{Anthrakidis2012, author = {Anthrakidis, Anette}, title = {Pr{\"u}feinrichtung zur Bestimmung der Leistungsf{\"a}higkeit von solarthermischen Kollektoren bis 200 Grad C}, series = {22. Symposium Thermische Solarenergie : 09. bis 11. Mai 2012, Kloster Banz, Bad Staffelstein}, booktitle = {22. Symposium Thermische Solarenergie : 09. bis 11. Mai 2012, Kloster Banz, Bad Staffelstein}, publisher = {OTTI}, address = {Regensburg}, isbn = {978-3-941785-89-2}, pages = {134 -- 135}, year = {2012}, language = {de} } @inproceedings{HuckPoghossianBaeckeretal.2013, author = {Huck, Christina and Poghossian, Arshak and B{\"a}cker, Matthias and Zander, W. and Schubert, J. and Sukoyan, L. H. and Begoyan, V. and Buniatyan, V. V. and Wagner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Chemische Sensoren mit Bariumstrontiumtitanat als funktionelle Schicht zur Multiparameterdetektion}, series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013}, booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013}, organization = {Dresdner Sensor-Symposium <11, 2013>}, isbn = {978-3-9813484-5-3}, pages = {368 -- 372}, year = {2013}, language = {de} } @inproceedings{SchusserBaeckerLeinhosetal.2013, author = {Schusser, Sebastian and B{\"a}cker, Matthias and Leinhos, Marcel and Krischer, M. and Wenzel, L. and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Sensorkonzept zur in vitro Echtzeitmessung des Degradationsverhaltens von biodegradierbaren Biopolymeren}, series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013}, booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013}, organization = {Dresdner Sensor-Symposium <11, 2013>}, isbn = {978-3-9813484-5-3}, pages = {174 -- 177}, year = {2013}, language = {de} } @inproceedings{BungSunMeirelesetal.2012, author = {Bung, Daniel Bernhard and Sun, Q. and Meireles, I. and Matos, J. and Viseu, T.}, title = {USBR type III stilling basin performance for steep stepped spillways}, series = {Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto}, booktitle = {Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto}, organization = {International Symposium on Hydraulic Structures <4, 2012, Porto>}, isbn = {978-989-8509-01-7}, pages = {Elektronisch publiziert}, year = {2012}, language = {en} } @inproceedings{KerpenBungSchlurmann2010, author = {Kerpen, N. B. and Bung, Daniel Bernhard and Schlurmann, Torsten}, title = {Physical model investigations of pressure distributions next to ships passing through a lock}, series = {5th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : CG JOINT 2010}, booktitle = {5th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : CG JOINT 2010}, publisher = {Univ. Press}, address = {Tianjin}, organization = {Chinese-German Joint Symposium on Hydraulic and Ocean Engineering <5, 2010, Tianjin>}, isbn = {978-7-5618-3671-2}, pages = {514 -- 519}, year = {2010}, language = {en} } @inproceedings{GogolinCarvalhoBungetal.2013, author = {Gogolin, C. and Carvalho, R. and Bung, Daniel Bernhard and Matos, J.}, title = {Experimental and numerical investigation of steady and unsteady flows in roughened channels with cross beams}, series = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China}, booktitle = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China}, publisher = {Tsinghua Univ. Press}, address = {Beijing}, organization = {International Association for Hydraulic Engineering and Research}, pages = {Artikelkennnummer: A10837C}, year = {2013}, language = {en} } @inproceedings{OertelBung2012, author = {Oertel, Mario and Bung, Daniel Bernhard}, title = {Characteristics of cross-bar block ramp flows}, series = {Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto}, booktitle = {Hydraulic structures into the 21st century : 4th IAHR International Symposium on Hydraulic Structures : 9.-11.2.2012, Porto}, organization = {International Symposium on Hydraulic Structures <4, 2012, Porto>}, isbn = {978-989-8509-01-7}, pages = {Elektronisch publiziert}, year = {2012}, language = {en} } @inproceedings{SchlurmannBung2012, author = {Schlurmann, Torsten and Bung, Daniel Bernhard}, title = {Experimental investigation of flow-induced radial gate vibrations at Lower Subansiri dam}, series = {Sixth Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : JOINT 2012 : 23.-29.9.2012, Keelung}, booktitle = {Sixth Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : JOINT 2012 : 23.-29.9.2012, Keelung}, organization = {Chinese-German Joint Symposium on Hydraulic and Ocean Engineering <6, 2012, Keelung>}, pages = {7 -- 14}, year = {2012}, language = {en} } @inproceedings{OertelBung2013, author = {Oertel, Mario and Bung, Daniel Bernhard}, title = {Comparison of 2D dam-break waves with VOF and SPH method}, series = {Proceedings of the 35th IAHR world congress : 8.-13.9.2013, Chengdu, China}, booktitle = {Proceedings of the 35th IAHR world congress : 8.-13.9.2013, Chengdu, China}, publisher = {Tsinghua Univ. Press}, address = {Beijing}, organization = {International Association for Hydraulic Engineering and Research}, pages = {Artikelkennnummer: A11113}, year = {2013}, language = {en} } @inproceedings{Bung2013, author = {Bung, Daniel Bernhard}, title = {Air-water surface roughness in self-aerated stepped spillway flows}, series = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China}, booktitle = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China}, publisher = {Tsinghua Univ. Press}, address = {Beijing}, organization = {International Association for Hydraulic Engineering and Research}, pages = {Artikelkennnummer: A11045}, year = {2013}, language = {en} } @inproceedings{BeckerEggertBruningetal.2013, author = {Becker, J{\"o}rg and Eggert, Mathias and Bruning, Dennis and Saat, Jan}, title = {Applicability of Business Process Model Analysis Approaches - A Case Study in Financial Services Consulting}, series = {Wirtschaftsinformatik Proceedings 2013}, booktitle = {Wirtschaftsinformatik Proceedings 2013}, pages = {1181 -- 1195}, year = {2013}, language = {en} } @inproceedings{SattlerChicoCaminosUerlingsetal.2020, author = {Sattler, Johannes Christoph and Chico Caminos, Ricardo Alexander and {\"U}rlings, Nicolas and Dutta, Siddharth and Ruiz, Victor and Kalogirou, Soteris and Ktistis, Panayiotis and Agathokleous, Rafaela and Jung, Christian and Alexopoulos, Spiros and Atti, Vikrama Nagababu and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf}, title = {Operational experience and behaviour of a parabolic trough collector system with concrete thermal energy storage for process steam generation in Cyprus}, series = {AIP Conference Proceedings}, booktitle = {AIP Conference Proceedings}, number = {2303}, doi = {10.1063/5.0029278}, pages = {140004-1 -- 140004-10}, year = {2020}, abstract = {As part of the transnational research project EDITOR, a parabolic trough collector system (PTC) with concrete thermal energy storage (C-TES) was installed and commissioned in Limassol, Cyprus. The system is located on the premises of the beverage manufacturer KEAN Soft Drinks Ltd. and its function is to supply process steam for the factory's pasteurisation process [1]. Depending on the factory's seasonally varying capacity for beverage production, the solar system delivers between 5 and 25 \% of the total steam demand. In combination with the C-TES, the solar plant can supply process steam on demand before sunrise or after sunset. Furthermore, the C-TES compensates the PTC during the day in fluctuating weather conditions. The parabolic trough collector as well as the control and oil handling unit is designed and manufactured by Protarget AG, Germany. The C-TES is designed and produced by CADE Soluciones de Ingenier{\´i}a, S.L., Spain. In the focus of this paper is the description of the operational experience with the PTC, C-TES and boiler during the commissioning and operation phase. Additionally, innovative optimisation measures are presented.}, language = {en} } @inproceedings{SchoppHeuermannMarso2017, author = {Schopp, Christoph and Heuermann, Holger and Marso, Michel}, title = {Multiphysical Study of an Atmospheric Microwave Argon Plasma Jet}, series = {IEEE Transactions on Plasma Science}, volume = {45}, booktitle = {IEEE Transactions on Plasma Science}, number = {6}, publisher = {IEEE}, issn = {1939-9375}, doi = {10.1109/TPS.2017.2692735}, pages = {932 -- 937}, year = {2017}, language = {en} } @inproceedings{KrueckelNoldenFerreinetal.2015, author = {Kr{\"u}ckel, Kai and Nolden, Florian and Ferrein, Alexander and Scholl, Ingrid}, title = {Intuitive visual teleoperation for UGVs using free-look augmented reality displays}, series = {2015 IEEE International Conference on Robotics and Automation (ICRA), Seattle, WA}, booktitle = {2015 IEEE International Conference on Robotics and Automation (ICRA), Seattle, WA}, doi = {10.1109/ICRA.2015.7139809}, pages = {4412 -- 4417}, year = {2015}, language = {en} } @inproceedings{ButenwegMeyerFehling2014, author = {Butenweg, Christoph and Meyer, Udo and Fehling, Ekkehard}, title = {INSYSME: first activities of the German partners}, series = {9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014}, booktitle = {9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014}, year = {2014}, language = {en} } @inproceedings{HuckBaeckerPoghossianetal.2011, author = {Huck, Christina and B{\"a}cker, Matthias and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Bifunktionaler Sensorchip f{\"u}r den Nachweis von Gel{\"o}stwasserstoff}, isbn = {978-3942710-53-4}, doi = {10.5162/10dss2011/16.10}, pages = {325 -- 328}, year = {2011}, language = {de} } @inproceedings{NeumannDuelbergSchifferetal.2016, author = {Neumann, Tobias and D{\"u}lberg, Enno and Schiffer, Stefan and Ferrein, Alexander}, title = {A rotating platform for swift acquisition of dense 3D point clouds}, series = {Intelligent Robotics and Applications: 9th International Conference, ICIRA 2016, Tokyo, Japan, August 22-24, 2016, Proceedings, Part I}, volume = {9834}, booktitle = {Intelligent Robotics and Applications: 9th International Conference, ICIRA 2016, Tokyo, Japan, August 22-24, 2016, Proceedings, Part I}, publisher = {Springer}, isbn = {978-3-319-43505-3 (Print)}, doi = {10.1007/978-3-319-43506-0_22}, pages = {257 -- 268}, year = {2016}, language = {en} } @inproceedings{LudowicyRingsFingeretal.2019, author = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten and Bil, Cees}, title = {Impact of Propulsion Technology Levels on the Sizing and Energy Consumption for Serial HybridElectric General Aviation Aircraft}, series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019}, booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019}, pages = {14 Seiten}, year = {2019}, language = {en} } @inproceedings{SattlerAlexopoulosChicoCaminosetal.2019, author = {Sattler, Johannes Christoph and Alexopoulos, Spiros and Chico Caminos, Ricardo Alexander and Mitchell, John C. and Ruiz, Victor C. and Kalogirou, Soteris and Ktistis, Panayiotis K. and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf}, title = {Dynamic simulation model of a parabolic trough collector system with concrete thermal energy storage for process steam generation}, series = {AIP Conference Proceedings}, volume = {2126}, booktitle = {AIP Conference Proceedings}, issn = {0094243X}, doi = {10.1063/1.5117663}, pages = {150007-1 -- 150007-8}, year = {2019}, language = {en} } @inproceedings{GoettscheKornAmato2015, author = {G{\"o}ttsche, Joachim and Korn, Michael and Amato, Alexandre}, title = {The Passivhaus concept for the Arabian Peninsula - An energetic-economical evaluation considering the thermal comfort}, series = {QScience Proceedings: Vol 2015}, booktitle = {QScience Proceedings: Vol 2015}, doi = {10.5339/qproc.2015.qgbc.38}, pages = {8 Seiten}, year = {2015}, abstract = {The Passivhaus building standard is a concept developed for the realization of energy-efficient and economical buildings with a simultaneous high utilization comfort under European climate conditions. Major elements of the Passivhaus concept are a high thermal insulation of the external walls, the use of heat and/or solar shading glazing as well as an airtight building envelope in combination with energy-efficient technical building installations and heating or cooling generators, such as an efficient energy-recovery in the building air-conditioning. The objective of this research project is the inquiry to determine the parameters or constraints under which the Passivhaus concept can be implemented under the arid climate conditions in the Arabian Peninsula to achieve an energy-efficient and economical building with high utilization comfort. In cooperation between the Qatar Green Building Council (QGBC), Barwa Real Estate (BRE) and Kahramaa the first Passivhaus was constructed in Qatar and on the Arabian Peninsula in 2013. The Solar-Institut J{\"u}lich of Aachen University of Applied Science supports the Qatar Green Building Council with a dynamic building and equipment simulation of the Passivhaus and the neighbouring reference building. This includes simulation studies with different component configurations for the building envelope and different control strategies for heating or cooling systems as well as the air conditioning of buildings to find an energetic-economical optimum. Part of these analyses is the evaluation of the energy efficiency of the used energy recovery system in the Passivhaus air-conditioning and identification of possible energy-saving effects by the use of a bypass function integrated in the heat exchanger. In this way it is expected that on an annual basis the complete electricity demand of the building can be covered by the roof-integrated PV generator.}, language = {en} } @inproceedings{AnthrakidisHerrmannSchornetal.2015, author = {Anthrakidis, Anette and Herrmann, Ulf and Schorn, Christian and Schwarzer, Klemens and Wedding, Philipp and Weis, Fabian}, title = {Development and Testing of a Novel Method for the Determination of the Efficiency of Concentrating Solar Thermal Collectors}, series = {Conference Proceedings Solar World Congress 2015, Daegu, Korea, 08 - 12 November 2015}, booktitle = {Conference Proceedings Solar World Congress 2015, Daegu, Korea, 08 - 12 November 2015}, pages = {9 Seiten}, year = {2015}, language = {en} } @inproceedings{NaetherPoghossianPlatenetal.2006, author = {N{\"a}ther, Niko and Poghossian, Arshak and Platen, J. and Yoshinobu, T. and Koudelka-Hep, M. and Sch{\"o}ning, Michael Josef}, title = {Multi-parameter sensing of both physical and (bio-)chemical quantities using the same transducer principle}, series = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...}, booktitle = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...}, address = {Warsaw}, pages = {172 -- 181}, year = {2006}, language = {en} } @inproceedings{HeitzerStaat2000, author = {Heitzer, M. and Staat, Manfred}, title = {Direct FEM approach to design-by-analysis of pressurized components}, year = {2000}, abstract = {Abstracts of the ACHEMA 2000 - International Meeting on Chemical Engineering, Environmental Protection and Biotechnology, May 22 - 27, 2000. Frankfurt am Main. Achema 2000 : special edition / Linde. [Ed.: Linde AG. Red.: Volker R. Leski]. - Wiesbaden : Linde AG, 2000. - 56 p. : Ill., . - pp: 79 - 81}, subject = {Finite-Elemente-Methode}, language = {en} } @inproceedings{BungLangohrWaldenberger2023, author = {Bung, Daniel Bernhard and Langohr, Phillip and Waldenberger, Lisa}, title = {Influence of cycle number in CFD studies of labyrinth weirs}, series = {Proceedings of the 40th IAHR World Congress (Vienna, 2023)}, booktitle = {Proceedings of the 40th IAHR World Congress (Vienna, 2023)}, editor = {Habersack, Helmut and Tritthart, Michael}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, isbn = {978-90-833476-1-5}, issn = {L 2521-7119 (online)}, doi = {10.3850/978-90-833476-1-5_iahr40wc-p0531-cd}, year = {2023}, abstract = {The major advantage of labyrinth weirs over linear weirs is hydraulic efficiency. In hydraulic modeling efforts, this strength contrasts with limited pump capacity as well as limited computational power for CFD simulations. For the latter, reducing the number of investigated cycles can significantly reduce necessary computational time. In this study, a labyrinth weir with different cycle numbers was investigated. The simulations were conducted in FLOW-3D HYDRO as a Large Eddy Simulation. With a mean deviation of 1.75 \% between simulated discharge coefficients and literature design equations, a reasonable agreement was found. For downstream conditions, overall consistent results were observed as well. However, the orientation of labyrinth weirs with a single cycle should be chosen carefully under consideration of the individual research purpose.}, language = {en} } @inproceedings{HeuermannFinger2014, author = {Heuermann, Holger and Finger, Torsten}, title = {2.45 GHz Plasma Powered Spark Plug by Thermal and EM-Optimization}, pages = {30 Folien}, year = {2014}, language = {en} } @inproceedings{GoemmelNiendorfFrauenrathetal.2010, author = {G{\"o}mmel, Andreas and Niendorf, Thoralf and Frauenrath, Tobias and Otten, Mario and Butenweg, Christoph and Kob, Malte}, title = {3D vocal fold geometry mapping using Magnetic Resonance Imaging}, series = {Fortschritte der Akustik : 36. Deutsche Jahrestagung f{\"u}r Akustik, Band 1}, booktitle = {Fortschritte der Akustik : 36. Deutsche Jahrestagung f{\"u}r Akustik, Band 1}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik}, address = {Berlin}, organization = {Deutsche Jahrestagung f{\"u}r Akustik <36, 2010, Berlin>}, isbn = {978-3-9808659-8-2}, pages = {271 -- 272}, year = {2010}, language = {en} } @inproceedings{SchildtBraunMarcocca2017, author = {Schildt, P. and Braun, Carsten and Marcocca, P.}, title = {Flight testing the extra 330LE flying testbed}, series = {48th Annual International Symposium of the Society of Flight Test Engineers 2017}, booktitle = {48th Annual International Symposium of the Society of Flight Test Engineers 2017}, isbn = {978-151085387-4}, pages = {349 -- 362}, year = {2017}, language = {en} } @inproceedings{AlKaidyUlberTippkoetter2014, author = {Al-Kaidy, H. and Ulber, Roland and Tippk{\"o}tter, Nils}, title = {A platform technology for the automated reaction control in magnetizable micro-fluidic droplets}, series = {Biomaterials - made in bioreactors : book of abstracts, May 26 - 28, 2014, Radisson Blu Park Hotel and Conference Dentre, Radebeul, Germany}, booktitle = {Biomaterials - made in bioreactors : book of abstracts, May 26 - 28, 2014, Radisson Blu Park Hotel and Conference Dentre, Radebeul, Germany}, publisher = {DECHEMA}, address = {Frankfurt am Main}, pages = {21 -- 22}, year = {2014}, language = {en} } @inproceedings{FingerGoettenBraunetal.2019, author = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, C.}, title = {On Aircraft Design Under the Consideration of Hybrid-Electric Propulsion Systems}, series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)}, booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)}, publisher = {Springer}, address = {Singapore}, isbn = {978-981-13-3305-7}, doi = {10.1007/978-981-13-3305-7_99}, pages = {1261 -- 1272}, year = {2019}, abstract = {A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology.}, language = {en} } @inproceedings{OertelBungSchlenkhoff2012, author = {Oertel, Mario and Bung, Daniel Bernhard and Schlenkhoff, Andreas}, title = {Blocksteinrampen in Riegelbauweise : Neue Bemessungsans{\"a}tze}, series = {Staubauwerke : planen, bauen, betreiben; 35. Dresdner Wasserbaukolloquium 2012, 08. - 09. M{\"a}rz 2012}, booktitle = {Staubauwerke : planen, bauen, betreiben; 35. Dresdner Wasserbaukolloquium 2012, 08. - 09. M{\"a}rz 2012}, editor = {Carstensen, Dirk}, publisher = {Selbstverl. der Techn. Univ.}, address = {Dresden}, organization = {Technische Universit{\"a}t Dresden, Fakult{\"a}t Bauingenieurwesen}, isbn = {978-3-86780-261-1}, pages = {317 -- 326}, year = {2012}, language = {de} } @inproceedings{BeckerEggertSaatetal.2013, author = {Becker, J{\"o}rg and Eggert, Mathias and Saat, Jan and Dirding, Philipp}, title = {The Influence of Regulation on Data Warehouse Engineering - Investigating an IT Consulting Case in the Financial Service Industry}, series = {Proceedings of the Nineteenth Americas Conference on Information Systems, Chicago, Illinois, August 15-17, 2013.}, booktitle = {Proceedings of the Nineteenth Americas Conference on Information Systems, Chicago, Illinois, August 15-17, 2013.}, pages = {1 -- 8}, year = {2013}, language = {en} } @inproceedings{LuftGebhardtBalc2019, author = {Luft, Angela and Gebhardt, Andreas and Balc, Nicolae}, title = {Challenges of additive manufacturing in production systems}, series = {Modern technologies in manufacturing (MTeM 2019)}, volume = {299}, booktitle = {Modern technologies in manufacturing (MTeM 2019)}, number = {Article 01003}, doi = {10.1051/matecconf/201929901003}, pages = {6 Seiten}, year = {2019}, language = {en} } @inproceedings{SchoppHeuermannHoltrup2014, author = {Schopp, Christoph and Heuermann, Holger and Holtrup, S.}, title = {Investigation on efficacy optimization of RF-driven automotive D-lamps}, series = {44th European Microwave Conference (EuMC),2014, Rome}, booktitle = {44th European Microwave Conference (EuMC),2014, Rome}, doi = {10.1109/EuMC.2014.6986645}, pages = {1154 -- 1157}, year = {2014}, language = {en} } @inproceedings{TippkoetterMoehringMaureretal.2013, author = {Tippk{\"o}tter, Nils and M{\"o}hring, S. and Maurer, S. and Roth, J.}, title = {Dezentrale Vorbehandlung und Verarbeitung pflanzlicher Reststoffe f{\"u}r Bioraffinerien}, series = {Kurzfassungen der Vortr{\"a}ge nach Sessions : Fr{\"u}hjahrstagung der Biotechnologen 2013, 4. - 5. M{\"a}rz 2013, Dechema-Haus, Frankfurt am Main}, booktitle = {Kurzfassungen der Vortr{\"a}ge nach Sessions : Fr{\"u}hjahrstagung der Biotechnologen 2013, 4. - 5. M{\"a}rz 2013, Dechema-Haus, Frankfurt am Main}, address = {Frankfurt am Main}, pages = {5}, year = {2013}, language = {de} } @inproceedings{Tippkoetter2013, author = {Tippk{\"o}tter, Nils}, title = {Biotechnologische Gewinnung von Wertstoffen aus Molke : BiobasedWorld - Innovation in food}, series = {Biotechnica 2013 : European biotechnology science \& industry news}, volume = {12}, booktitle = {Biotechnica 2013 : European biotechnology science \& industry news}, number = {9, special}, pages = {33 -- 50}, year = {2013}, language = {de} } @inproceedings{WolfUlbrich2007, author = {Wolf, Martin R. and Ulbrich, Daniel}, title = {Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung}, year = {2007}, abstract = {Dr.-Ing. Martin Wolf ; Dipl.-Kaufm. Daniel Ulbrich , Dr. Pecher und Partner Ingenieurgesellschaft mbH, M{\"u}nchen. 31 S. (S. 139-168). Beitrag zum 1. Aachener Softwaretag in der Wasserwirtschaft < 1, 2007, Aachen>. Zusammenfasung [der Autoren] Die {\"o}ffentlichen Kanalnetze Deutschlands stellen mit einem Wert von rd. 330 Mrd. € ein enormes Anlageverm{\"o}gen dar. Auf Grund des oft schlechten Zustandes und geringer Ausgaben zur Instandhaltung und Erneuerung ist zu erwarten, dass durch die gegenw{\"a}rtige Sanierungspraxis eher ein Substanzwertverzehr des Kanalnetzes als ein Substanzwerterhalt im Sinne des Generationenvertrages erzielt wird. F{\"u}r einen nachhaltigen Betrieb und Erhalt der Kanalnetze sind deshalb Sanierungsstrategien erforderlich, die neben den technischen und gesetzlichen Anforderungen auch den mittel- und langfristigen Substanzwertverlauf ber{\"u}cksichtigen. Dieser wird beeinflusst vom erforderlichen oder durchgef{\"u}hrten Sanierungsumfang, Art und Zusammensetzung der ausgew{\"a}hlten Maßnahmen sowie der zeitlichen Abfolge der Sanierungsmaßnahmen. Erheblichen Einfluss auf den Substanzwertverlauf hat zudem die Ber{\"u}cksichtigung der hydraulischen Verh{\"a}ltnisse sowie der optisch nicht sichtbaren Undichtheiten. Entsprechend ist es erforderlich, die tats{\"a}chlich vorhandenen Defizite zu ermitteln und die Sanierungsmaßnahmen sowie eine Strategie zur Umsetzung zu erarbeiten. Da sich gezeigt hat, dass alleine die Einhaltung der technischen und gesetzlichen Anforderung f{\"u}r einen Substanzwerterhalt nicht ausreicht, muss die geplante Strategie im Dr.-Ing. Martin Wolf 139 von 170 Decision-Support-System kokas zur Sanierungsplanung und Strategieentwicklung 1. Aachener Softwaretag in der Wasserwirtschaft Hinblick auf die nachhaltige Wertentwicklung {\"u}berpr{\"u}ft und ggf. Anpassungen vorgenommen werden. Kurzfristig erzielte Einsparungen durch reduzierten Schadensumfang oder einseitige Maßnahmenwahl erm{\"o}glichen zwar im g{\"u}nstigsten Fall, die Anforderungen einzuhalten, gehen jedoch zwangsl{\"a}ufig zu Lasten des Substanzwertes und f{\"u}hren mittel- und langfristig zu einer Versch{\"a}rfung der Kosten- und Geb{\"u}hrensituation. Der monet{\"a}re, am konkreten Sanierungsaufwand orientierte Substanzwertansatz erm{\"o}glicht dabei, technische und kaufm{\"a}nnische Gesichtspunkte praxisnah zu verkn{\"u}pfen und den bestm{\"o}glichen Ausgleich zwischen den gegenl{\"a}ufigen Zielen Substanzwerterhalt und Geb{\"u}hrenkonstanz zu finden.}, subject = {Kanalisation}, language = {de} } @inproceedings{BungOertel2019, author = {Bung, Daniel Bernhard and Oertel, Mario}, title = {Wave breaking over a submerged horizontal plate: Optical Flow, LES and RANS}, series = {E-proceedings of the 38th IAHR World Congress September 1-6, 2019, Panama City, Panama}, booktitle = {E-proceedings of the 38th IAHR World Congress September 1-6, 2019, Panama City, Panama}, doi = {10.3850/38WC092019-0509}, pages = {3690 -- 3698}, year = {2019}, language = {en} } @inproceedings{LudowicyRingsFingeretal.2018, author = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten}, title = {Sizing Studies of Light Aircraft with Serial Hybrid Propulsion Systems}, series = {Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen}, booktitle = {Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen}, pages = {11 S.}, year = {2018}, language = {en} } @inproceedings{NeumannFerreinKallweitetal.2014, author = {Neumann, Tobias and Ferrein, Alexander and Kallweit, Stephan and Scholl, Ingrid}, title = {Towards a mobile mapping robot for underground mines}, series = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town}, booktitle = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town}, organization = {Conference of Robotics and Mechatronics <7, 2014, Cape Town, South Africa>}, pages = {1 -- 6}, year = {2014}, language = {en} } @inproceedings{BungTullis2018, author = {Bung, Daniel Bernhard and Tullis, Blake}, title = {Hydraulic Structures - ISHS2018 in Perspective}, series = {7th IAHR International Symposium on Hydraulic Structures, Aachen, Germany, 15-18 May}, booktitle = {7th IAHR International Symposium on Hydraulic Structures, Aachen, Germany, 15-18 May}, isbn = {978-0-692-13277-7}, doi = {10.15142/T3WH2B}, pages = {9 seiten}, year = {2018}, language = {en} } @inproceedings{LudowicyRingsFingeretal.2018, author = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten}, title = {Sizing Studies of Light Aircraft with Parallel Hybrid Propulsion Systems}, series = {Deutscher Luft- und Raumfahrtkongress 2018}, booktitle = {Deutscher Luft- und Raumfahrtkongress 2018}, doi = {10.25967/480227}, pages = {15 S.}, year = {2018}, language = {en} } @inproceedings{ThurnGebhardt2018, author = {Thurn, Laura and Gebhardt, Andreas}, title = {Strategy of Education on Materials for Students}, series = {Conference Proceedings: „New Perspectives in Science Education"}, booktitle = {Conference Proceedings: „New Perspectives in Science Education"}, address = {Florence, Italy}, isbn = {978-88-6292-976-9}, pages = {156 -- 161}, year = {2018}, language = {en} } @inproceedings{ButenwegGajewskiThierauf1999, author = {Butenweg, Christoph and Gajewski, R. and Thierauf, Georg}, title = {A practical approach for the optimum design of reinforced concrete structures}, series = {Developments in computational mechanics with high performance computing : [papers presented at the Third Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held in Weimar, Germany between 20 - 25 March 1999] / ed. by B. H. V. Topping}, booktitle = {Developments in computational mechanics with high performance computing : [papers presented at the Third Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held in Weimar, Germany between 20 - 25 March 1999] / ed. by B. H. V. Topping}, publisher = {Civil-Comp Press}, address = {Edinburgh}, organization = {Euro-Conference on Parallel and Distributed Computing for Computational Mechanics <3, 1999, Weimar>}, isbn = {0-94-8749-59-8}, pages = {245 -- 250}, year = {1999}, language = {en} } @inproceedings{PaulsenHoffstadtKrafftetal.2020, author = {Paulsen, Svea and Hoffstadt, Kevin and Krafft, Simone and Leite, A. and Zang, J. and Fonseca-Zang, W. and Kuperjans, Isabel}, title = {Continuous biogas production from sugarcane as sole substrate}, series = {Energy Reports}, volume = {6}, booktitle = {Energy Reports}, number = {Supplement 1}, publisher = {Elsevier}, doi = {10.1016/j.egyr.2019.08.035}, pages = {153 -- 158}, year = {2020}, abstract = {A German-Brazilian research project investigates sugarcane as an energy plant in anaerobic digestion for biogas production. The aim of the project is a continuous, efficient, and stable biogas process with sugarcane as the substrate. Tests are carried out in a fermenter with a volume of 10 l. In order to optimize the space-time load to achieve a stable process, a continuous process in laboratory scale has been devised. The daily feed in quantity and the harvest time of the substrate sugarcane has been varied. Analyses of the digester content were conducted twice per week to monitor the process: The ratio of inorganic carbon content to volatile organic acid content (VFA/TAC), the concentration of short-chain fatty acids, the organic dry matter, the pH value, and the total nitrogen, phosphate, and ammonium concentrations were monitored. In addition, the gas quality (the percentages of CO₂, CH₄, and H₂) and the quantity of the produced gas were analyzed. The investigations have exhibited feasible and economical production of biogas in a continuous process with energy cane as substrate. With a daily feeding rate of 1.68gᵥₛ/l*d the average specific gas formation rate was 0.5 m3/kgᵥₛ. The long-term study demonstrates a surprisingly fast metabolism of short-chain fatty acids. This indicates a stable and less susceptible process compared to other substrates.}, language = {en} } @inproceedings{NethSchubaBrodkorbetal.2023, author = {Neth, Jannik and Schuba, Marko and Brodkorb, Karsten and Neugebauer, Georg and H{\"o}ner, Tim and Hack, Sacha}, title = {Digital forensics triage app for android}, series = {ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security}, booktitle = {ARES '23: Proceedings of the 18th International Conference on Availability, Reliability and Security}, publisher = {ACM}, isbn = {9798400707728}, doi = {10.1145/3600160.3605017}, pages = {6 Seiten}, year = {2023}, abstract = {Digital forensics of smartphones is of utmost importance in many criminal cases. As modern smartphones store chats, photos, videos etc. that can be relevant for investigations and as they can have storage capacities of hundreds of gigabytes, they are a primary target for forensic investigators. However, it is exactly this large amount of data that is causing problems: extracting and examining the data from multiple phones seized in the context of a case is taking more and more time. This bears the risk of wasting a lot of time with irrelevant phones while there is not enough time left to analyze a phone which is worth examination. Forensic triage can help in this case: Such a triage is a preselection step based on a subset of data and is performed before fully extracting all the data from the smartphone. Triage can accelerate subsequent investigations and is especially useful in cases where time is essential. The aim of this paper is to determine which and how much data from an Android smartphone can be made directly accessible to the forensic investigator - without tedious investigations. For this purpose, an app has been developed that can be used with extremely limited storage of data in the handset and which outputs the extracted data immediately to the forensic workstation in a human- and machine-readable format.}, language = {en} } @inproceedings{NeugebauerBrutschyMeyeretal.2014, author = {Neugebauer, Georg and Brutschy, Lucas and Meyer, Ulrike and Wetzel, Susanne}, title = {Privacy-preserving multi-party reconciliation secure in the malicious model}, series = {DPM 2013, SETOP 2013: Data Privacy Management and Autonomous Spontaneous Security}, booktitle = {DPM 2013, SETOP 2013: Data Privacy Management and Autonomous Spontaneous Security}, editor = {Garcia-Alfaro, Joaquin and Lioudakis, Georgios and Cuppens-Boulahia, Nora and Foley, Simon and Fitzgerald, William M.}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-642-54567-2 (Print)}, doi = {10.1007/978-3-642-54568-9_12}, pages = {178 -- 193}, year = {2014}, abstract = {The problem of fair and privacy-preserving ordered set reconciliation arises in a variety of applications like auctions, e-voting, and appointment reconciliation. While several multi-party protocols have been proposed that solve this problem in the semi-honest model, there are no multi-party protocols that are secure in the malicious model so far. In this paper, we close this gap. Our newly proposed protocols are shown to be secure in the malicious model based on a variety of novel non-interactive zero-knowledge-proofs. We describe the implementation of our protocols and evaluate their performance in comparison to protocols solving the problem in the semi-honest case.}, language = {en} } @inproceedings{SildatkeKarwanniKraftetal.2020, author = {Sildatke, Michael and Karwanni, Hendrik and Kraft, Bodo and Schmidts, Oliver and Z{\"u}ndorf, Albert}, title = {Automated Software Quality Monitoring in Research Collaboration Projects}, series = {ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops}, booktitle = {ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops}, publisher = {IEEE}, address = {New York, NY}, doi = {10.1145/3387940.3391478}, pages = {603 -- 610}, year = {2020}, abstract = {In collaborative research projects, both researchers and practitioners work together solving business-critical challenges. These projects often deal with ETL processes, in which humans extract information from non-machine-readable documents by hand. AI-based machine learning models can help to solve this problem. Since machine learning approaches are not deterministic, their quality of output may decrease over time. This fact leads to an overall quality loss of the application which embeds machine learning models. Hence, the software qualities in development and production may differ. Machine learning models are black boxes. That makes practitioners skeptical and increases the inhibition threshold for early productive use of research prototypes. Continuous monitoring of software quality in production offers an early response capability on quality loss and encourages the use of machine learning approaches. Furthermore, experts have to ensure that they integrate possible new inputs into the model training as quickly as possible. In this paper, we introduce an architecture pattern with a reference implementation that extends the concept of Metrics Driven Research Collaboration with an automated software quality monitoring in productive use and a possibility to auto-generate new test data coming from processed documents in production. Through automated monitoring of the software quality and auto-generated test data, this approach ensures that the software quality meets and keeps requested thresholds in productive use, even during further continuous deployment and changing input data.}, language = {en} } @inproceedings{Kurz2008, author = {Kurz, Melanie}, title = {On the benefit of moving images for the evaluation of form in virtual space : reflections in model theory}, series = {Design and semantics of form and movement : DeSForM 2008 ; [Hochschule f{\"u}r Gestaltung Offenbach am Main, 6.-7.11.2008]}, booktitle = {Design and semantics of form and movement : DeSForM 2008 ; [Hochschule f{\"u}r Gestaltung Offenbach am Main, 6.-7.11.2008]}, editor = {Feijs, Loe}, publisher = {Philips}, address = {Eindhoven}, isbn = {978-90-809801-2-9}, pages = {31 -- 34}, year = {2008}, language = {en} }