@article{FingerBraunBil2020, author = {Finger, Felix and Braun, Carsten and Bil, Cees}, title = {Impact of Battery Performance on the Initial Sizing of Hybrid-Electric General Aviation Aircraft}, series = {Journal of Aerospace Engineering}, volume = {33}, journal = {Journal of Aerospace Engineering}, number = {3}, publisher = {ASCE}, address = {Reston, Va.}, issn = {1943-5525}, doi = {10.1061/(ASCE)AS.1943-5525.0001113}, year = {2020}, abstract = {Studies suggest that hybrid-electric aircraft have the potential to generate fewer emissions and be inherently quieter when compared to conventional aircraft. By operating combustion engines together with an electric propulsion system, synergistic benefits can be obtained. However, the performance of hybrid-electric aircraft is still constrained by a battery's energy density and discharge rate. In this paper, the influence of battery performance on the gross mass for a four-seat general aviation aircraft with a hybrid-electric propulsion system is analyzed. For this design study, a high-level approach is chosen, using an innovative initial sizing methodology to determine the minimum required aircraft mass for a specific set of requirements and constraints. Only the peak-load shaving operational strategy is analyzed. Both parallel- and serial-hybrid propulsion configurations are considered for two different missions. The specific energy of the battery pack is varied from 200 to 1,000 W⋅h/kg, while the discharge time, and thus the normalized discharge rating (C-rating), is varied between 30 min (2C discharge rate) and 2 min (30C discharge rate). With the peak-load shaving operating strategy, it is desirable for hybrid-electric aircraft to use a light, low capacity battery system to boost performance. For this case, the battery's specific power rating proved to be of much higher importance than for full electric designs, which have high capacity batteries. Discharge ratings of 20C allow a significant take-off mass reduction aircraft. The design point moves to higher wing loadings and higher levels of hybridization if batteries with advanced technology are used.}, language = {en} } @article{GerhardtWacker1999, author = {Gerhardt, Hans Joachim and Wacker, J.}, title = {Immissionsprognosen auf der Basis von Windkanaluntersuchungen}, series = {Immissionsschutz. 4 (1999), H. 3}, journal = {Immissionsschutz. 4 (1999), H. 3}, isbn = {1430-9262}, pages = {84 -- 89}, year = {1999}, language = {de} } @article{DachwaldMikuckiTulaczyketal.2014, author = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng}, title = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems}, series = {Annals of Glaciology}, volume = {55}, journal = {Annals of Glaciology}, number = {65}, publisher = {Cambridge University Press}, address = {Cambridge}, issn = {1727-5644}, doi = {10.3189/2014AoG65A004}, pages = {14 -- 22}, year = {2014}, abstract = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.}, language = {en} } @article{BlomeKundt1987, author = {Blome, Hans-Joachim and Kundt, W.}, title = {Hypersonic Jets from Young Stars in Molecular Clouds}, series = {Circumstellar matter : proceedings of the 122nd symposium of the Internat. Astronom. Union held in Heidelberg, FRG, June 23 - 27, 1986 / ed. by I. Appenzeller ...}, journal = {Circumstellar matter : proceedings of the 122nd symposium of the Internat. Astronom. Union held in Heidelberg, FRG, June 23 - 27, 1986 / ed. by I. Appenzeller ...}, publisher = {Reidel}, address = {Dordrecht u.a.}, isbn = {90-277-2511-X}, pages = {73 -- 74}, year = {1987}, language = {en} } @article{DickhoffHorikawaFunke2021, author = {Dickhoff, Jens and Horikawa, Atsushi and Funke, Harald}, title = {Hydrogen Combustion - new DLE Combustor Addresses NOx Emissions and Flashback}, series = {Turbomachinery international : the global journal of energy equipment}, volume = {62}, journal = {Turbomachinery international : the global journal of energy equipment}, number = {4}, publisher = {MJH Life Sciences}, address = {Cranbury}, issn = {2767-2328}, pages = {26 -- 27}, year = {2021}, language = {en} } @article{Baums1992, author = {Baums, Bodo}, title = {Hubschrauberzellen aus Faserverbund-Werkstoffen}, series = {Kunststoffe. 82 (1992), H. 11}, journal = {Kunststoffe. 82 (1992), H. 11}, isbn = {0023-5563}, pages = {1114 -- 1118}, year = {1992}, language = {de} } @article{BohndickBosseJaenschetal.2021, author = {Bohndick, Carla and Bosse, Elke and J{\"a}nsch, Vanessa K. and Barnat, Miriam}, title = {How different diversity factors affect the perception of first-year requirements in higher education}, series = {Frontline Learning Research}, volume = {9}, journal = {Frontline Learning Research}, number = {2}, publisher = {EARLI}, issn = {2295-3159}, doi = {10.14786/flr.v9i2.667}, pages = {78 -- 95}, year = {2021}, abstract = {In the light of growing university entry rates, higher education institutions not only serve larger numbers of students, but also seek to meet first-year students' ever more diverse needs. Yet to inform universities how to support the transition to higher education, research only offers limited insights. Current studies tend to either focus on the individual factors that affect student success or they highlight students' social background and their educational biography in order to examine the achievement of selected, non-traditional groups of students. Both lines of research appear to lack integration and often fail to take organisational diversity into account, such as different types of higher education institutions or degree programmes. For a more comprehensive understanding of student diversity, the present study includes individual, social and organisational factors. To gain insights into their role for the transition to higher education, we examine how the different factors affect the students' perception of the formal and informal requirements of the first year as more or less difficult to cope with. As the perceived requirements result from both the characteristics of the students and the institutional context, they allow to investigate transition at the interface of the micro and the meso level of higher education. Latent profile analyses revealed that there are no profiles with complex patterns of perception of the first-year requirements, but the identified groups rather differ in the overall level of perceived challenges. Moreover, SEM indicates that the differences in the perception largely depend on the individual factors self-efficacy and volition.}, language = {en} } @article{Bullerschen1989, author = {Bullerschen, Klaus-Gerd}, title = {Hochtemperaturtechnik. Interne Arbeitssitzung des GVC-Fachausschusses 'Hochtemperaturtechnik'}, series = {Chemie Ingenieur Technik. 61 (1989), H. 6}, journal = {Chemie Ingenieur Technik. 61 (1989), H. 6}, isbn = {0009-286X}, pages = {510 -- 512}, year = {1989}, language = {de} } @article{BullerschenLeonard1990, author = {Bullerschen, Klaus-Gerd and L{\´e}onard, G.}, title = {Hochtemperaturtechnik}, series = {Chemie Ingenieur Technik. 62 (1990), H. 3}, journal = {Chemie Ingenieur Technik. 62 (1990), H. 3}, isbn = {0009-286X}, pages = {252 -- 256}, year = {1990}, language = {de} } @article{SchirraWatmuffBauschat2014, author = {Schirra, Julian and Watmuff, Jonathan and Bauschat, J.-Michael}, title = {Highly non-planar lifting systems: a relative assessment of existing potential-methodologies to accurately estimate the induced drag}, series = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.}, journal = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.}, organization = {American Institute of Aeronautics and Astronautics}, isbn = {978-1-62410-288-2}, doi = {10.2514/6.2014-2988}, pages = {Publ. online}, year = {2014}, language = {en} } @article{WittmannKellWinkleretal.1998, author = {Wittmann, Klaus and Kell, G. and Winkler, F. and G{\"u}nther, M. (u.a.)}, title = {High resolution temperature measurement technique for materials sciences experiments in space}, series = {Acta Astronautica. 43 (1998), H. 7-8}, journal = {Acta Astronautica. 43 (1998), H. 7-8}, isbn = {0094-5765}, pages = {385 -- 395}, year = {1998}, language = {en} } @article{BarnatFariaBosse2017, author = {Barnat, Miriam and Faria, Joana Abelha and Bosse, Elke}, title = {Heterogenit{\"a}t und Studierf{\"a}higkeit: Erste Ergebnisse einer L{\"a}ngsschnittbefragung}, series = {Qualit{\"a}t in der Wissenschaft: QiW ; Zeitschrift f{\"u}r Qualit{\"a}tsentwicklung in Forschung, Studium und Administration}, volume = {11}, journal = {Qualit{\"a}t in der Wissenschaft: QiW ; Zeitschrift f{\"u}r Qualit{\"a}tsentwicklung in Forschung, Studium und Administration}, number = {1}, publisher = {UVW Universit{\"a}ts-Verlag Webler}, address = {Bielefeld}, issn = {1860-3041}, pages = {17 -- 24}, year = {2017}, language = {de} } @article{DachwaldLeipoldFichtner2003, author = {Dachwald, Bernd and Leipold, M. and Fichtner, H.}, title = {Heliopause Explorer - A Sailcraft Mission to the Outer Boundaries of the Solar System / M. Leipold ; H. Fichtner ; B. Heber ... B. Dachwald ...}, series = {Proceedings of the Fifth IAA International Conference on Low Cost Planetary Missions : 24 - 26 September 2003, ESTEC, Noordwijk, the Netherlands / [comp. by R. A. Harris]}, journal = {Proceedings of the Fifth IAA International Conference on Low Cost Planetary Missions : 24 - 26 September 2003, ESTEC, Noordwijk, the Netherlands / [comp. by R. A. Harris]}, publisher = {ESA}, address = {Noordwijk}, isbn = {92-9092-853-0}, pages = {367 -- 375}, year = {2003}, language = {en} } @article{LeipoldFichtnerHeberetal.2006, author = {Leipold, M. and Fichtner, H. and Heber, B. and Groepper, P. and Lascar, S. and Burger, F. and Eiden, M. and Niederstadt, T. and Sickinger, C. and Herbeck, L. and Dachwald, Bernd and Seboldt, W.}, title = {Heliopause Explorer - A Sailcraft Mission to the Outer Boundaries of the Solar System}, series = {Acta Astronautica. 59 (2006), H. 8-11}, journal = {Acta Astronautica. 59 (2006), H. 8-11}, isbn = {0094-5765}, pages = {786 -- 796}, year = {2006}, language = {en} } @article{DachwaldMacDonaldMcInnes2007, author = {Dachwald, Bernd and MacDonald, Malcolm and McInnes, Colin R.}, title = {Heliocentric Solar Sail Orbit Transfers with Locally Optimal Control Laws / Malcolm Macdonald ; Colin McInnes ; Bernd Dachwald}, series = {Journal of Spacecraft and Rockets. 44 (2007), H. 1}, journal = {Journal of Spacecraft and Rockets. 44 (2007), H. 1}, isbn = {0022-4650}, pages = {273 -- 276}, year = {2007}, language = {en} } @article{PolaczekHenn2008, author = {Polaczek, Christa and Henn, Gudrun}, title = {Gute Vorkenntnisse verk{\"u}rzen die Studienzeit}, series = {Mathematikinformation : eine Zeitschrift von Begabtenf{\"o}rderung Mathematik e.V.}, volume = {2008}, journal = {Mathematikinformation : eine Zeitschrift von Begabtenf{\"o}rderung Mathematik e.V.}, number = {49}, publisher = {Begabtenf{\"o}rderung Mathematik}, address = {Neubiberg}, issn = {1612-9156}, pages = {46 -- 50}, year = {2008}, language = {de} } @article{RoethNowackOberschelpetal.2009, author = {R{\"o}th, Thilo and Nowack, Niels and Oberschelp, Christian and Lao, Bin}, title = {Gute Perspektiven f{\"u}r Stahl-Alumnium-Hybride im Automotivebereich / Nowack, Niels ; Oberschelp, Christian ; Lao, Bin ; Klaus, Gerald ; B{\"u}hrig-Polaczek, Andreas ; R{\"o}th, Thilo}, series = {Giesserei : die Zeitschrift f{\"u}r Technik, Innovation und Management. 96 (2009), H. 5}, journal = {Giesserei : die Zeitschrift f{\"u}r Technik, Innovation und Management. 96 (2009), H. 5}, isbn = {0016-9765}, pages = {110 -- 123}, year = {2009}, language = {de} } @article{DahmannHagemeisterNageletal.2002, author = {Dahmann, Peter and Hagemeister, W. and Nagel, and Exner,}, title = {Geschwindigkeits- und Positionsregelung eines hydraulischen Handlingger{\"a}tes in einem Ziegelwerk durch frequenzgeregelte Innenzahnradpumpe im Mehrquadrantenbetrieb}, series = {Fluid power focused on applications : 3rd International Fluid Power Conference (3rd IFK) ; [conference proceedings, March 5th and 6th 2002, Aachen, Germany]. Fluidtechnik, Band T3}, journal = {Fluid power focused on applications : 3rd International Fluid Power Conference (3rd IFK) ; [conference proceedings, March 5th and 6th 2002, Aachen, Germany]. Fluidtechnik, Band T3}, publisher = {Shaker}, address = {Aachen}, isbn = {3-8265-9900-4}, pages = {83 -- 94}, year = {2002}, language = {de} } @article{DahmannHagemeisterNageletal.2006, author = {Dahmann, Peter and Hagemeister, Wilhelm and Nagel, G{\"u}nther and Exner, Peter}, title = {Geregelte Innenzahnradpumpe im Mehrquadrantenbetrieb Geschwindigkeits- und Positionsregelung eines hydraulischen Handlingger{\"a}tes}, series = {O+P {\"O}lhydraulik und Pneumatik. 24 (2006), H. 1}, journal = {O+P {\"O}lhydraulik und Pneumatik. 24 (2006), H. 1}, isbn = {0341-2660}, pages = {24 -- 28}, year = {2006}, language = {de} } @article{EschGoebel1993, author = {Esch, Thomas and G{\"o}bel, T.}, title = {Gemischbildung bei drosselfreier Laststeuerung von Ottomotoren}, series = {Motortechnische Zeitschrift. 54 (1993), H. 12}, journal = {Motortechnische Zeitschrift. 54 (1993), H. 12}, isbn = {0024-8525}, pages = {616 -- 618}, year = {1993}, language = {de} } @article{Dahmann1993, author = {Dahmann, Peter}, title = {Funktionsweise von Hydraulikfiltern}, series = {{\"O}lhydraulik und Pneumatik. 37 (1993), H. 2}, journal = {{\"O}lhydraulik und Pneumatik. 37 (1993), H. 2}, isbn = {0341-2660}, pages = {118 -- 122}, year = {1993}, language = {de} } @article{DachwaldTuryshevDittusetal.2005, author = {Dachwald, Bernd and Turyshev, Slava G. and Dittus, H. and Shao, M. [u.a.]}, title = {Fundamental Physics with the Laser Astrometric Test Of Relativity / S.G. Turyshev ; H. Dittus ; M. Shao ... B.Dachwald ...}, series = {Proceedings of the 39th ESLAB Symposium "Trends in Space Science and Cosmic Vision 2020" : 19 - 21 April 2005, ESTEC, Noordwijk, the Netherlands / European Space Agency. [Comp. by: F. Favata ...] . - (ESA SP ; 588)}, journal = {Proceedings of the 39th ESLAB Symposium "Trends in Space Science and Cosmic Vision 2020" : 19 - 21 April 2005, ESTEC, Noordwijk, the Netherlands / European Space Agency. [Comp. by: F. Favata ...] . - (ESA SP ; 588)}, publisher = {ESA Publ. Div.}, address = {Noordwijk}, isbn = {9290928999}, pages = {8 -- 11}, year = {2005}, language = {en} } @article{NeuJanserKhatibietal.2017, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.}, title = {Fully Automated Operational Modal Analysis using multi-stage clustering}, series = {Mechanical Systems and Signal Processing}, volume = {Vol. 84, Part A}, journal = {Mechanical Systems and Signal Processing}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0888-3270}, doi = {10.1016/j.ymssp.2016.07.031}, pages = {308 -- 323}, year = {2017}, language = {en} } @article{GerhardtKramerJanssen1985, author = {Gerhardt, Hans Joachim and Kramer, C. and Janssen, L.-J.}, title = {Flow studies of an open jet wind tunnel and comparison with closed and slotted walls}, pages = {7 -- 28}, year = {1985}, language = {en} } @article{ScholzLeyDachwaldetal.2010, author = {Scholz, A. and Ley, Wilfried and Dachwald, Bernd and Miau, J. J. and Juang, J. C.}, title = {Flight results of the COMPASS-1 picosatellite mission}, series = {Acta Astronautica. 67 (2010), H. 9-10}, journal = {Acta Astronautica. 67 (2010), H. 9-10}, isbn = {0094-5765}, pages = {1289 -- 1298}, year = {2010}, language = {en} } @article{DachwaldSchmidtSeboldtetal.2003, author = {Dachwald, Bernd and Schmidt, Tanja D. and Seboldt, Wolfgang and Auweter-Kurtz,}, title = {Flight Opportunities from Mars to Earth for Piloted Missions Using Continuous Thrust Propulsion / Schmidt, Tanja D. ; Dachwald, Bernd ; Seboldt, Wolfgang ; Auweter-Kurtz, Monika}, publisher = {-}, pages = {1 -- 9}, year = {2003}, language = {en} } @article{SchmitzBartzHansen1991, author = {Schmitz, G{\"u}nter and Bartz, R. and Hansen, W.}, title = {Flexibles elektronisches Verbrennungsmotoren-Indiziersystem (FEVIS)}, series = {Vortr{\"a}ge und Kurzreferate : 13. und 14. November 1990, Congress Centrum, Magdeburg / Technische Universit{\"a}t "Otto von Guericke" Magdeburg, Fakult{\"a}t f{\"u}r Thermischen Maschinenbau, Institut f{\"u}r Maschinenmeßtechnik, Kolbenmaschinen und Instandhaltung}, journal = {Vortr{\"a}ge und Kurzreferate : 13. und 14. November 1990, Congress Centrum, Magdeburg / Technische Universit{\"a}t "Otto von Guericke" Magdeburg, Fakult{\"a}t f{\"u}r Thermischen Maschinenbau, Institut f{\"u}r Maschinenmeßtechnik, Kolbenmaschinen und Instandhaltung}, address = {Magdeburg}, pages = {485 -- 491}, year = {1991}, language = {de} } @article{FunkeBeckmann2022, author = {Funke, Harald and Beckmann, Nils}, title = {Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture}, series = {International Journal of Gas Turbine, Propulsion and Power Systems}, volume = {13}, journal = {International Journal of Gas Turbine, Propulsion and Power Systems}, number = {2}, issn = {1882-5079}, pages = {1 -- 7}, year = {2022}, abstract = {The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.\% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance}, language = {en} } @article{RoethKernKirchneretal.2009, author = {R{\"o}th, Thilo and Kern, Daniel and Kirchner, Karsten and Vietor, Thomas}, title = {Flexbody : Baukastensystem f{\"u}r Karosseriestrukturen / Kern, Daniel ; R{\"o}th, Thilo ; Kirchner, Karsten ; Vietor, Thomas}, series = {Mobiles : Fachzeitschrift f{\"u}r Konstrukteure. 35 (2009), H. 2009/2010}, journal = {Mobiles : Fachzeitschrift f{\"u}r Konstrukteure. 35 (2009), H. 2009/2010}, publisher = {Hochsch. f{\"u}r Angewandte Wiss.}, address = {Hamburg}, pages = {73 -- 75}, year = {2009}, language = {de} } @article{BaaderBoxbergChenetal.2023, author = {Baader, Fabian and Boxberg, Marc S. and Chen, Qian and F{\"o}rstner, Roger and Kowalski, Julia and Dachwald, Bernd}, title = {Field-test performance of an ice-melting probe in a terrestrial analogue environment}, series = {Icarus}, journal = {Icarus}, number = {409}, publisher = {Elsevier}, address = {Amsterdam}, doi = {10.1016/j.icarus.2023.115852}, pages = {Artikel 115852}, year = {2023}, abstract = {Melting probes are a proven tool for the exploration of thick ice layers and clean sampling of subglacial water on Earth. Their compact size and ease of operation also make them a key technology for the future exploration of icy moons in our Solar System, most prominently Europa and Enceladus. For both mission planning and hardware engineering, metrics such as efficiency and expected performance in terms of achievable speed, power requirements, and necessary heating power have to be known. Theoretical studies aim at describing thermal losses on the one hand, while laboratory experiments and field tests allow an empirical investigation of the true performance on the other hand. To investigate the practical value of a performance model for the operational performance in extraterrestrial environments, we first contrast measured data from terrestrial field tests on temperate and polythermal glaciers with results from basic heat loss models and a melt trajectory model. For this purpose, we propose conventions for the determination of two different efficiencies that can be applied to both measured data and models. One definition of efficiency is related to the melting head only, while the other definition considers the melting probe as a whole. We also present methods to combine several sources of heat loss for probes with a circular cross-section, and to translate the geometry of probes with a non-circular cross-section to analyse them in the same way. The models were selected in a way that minimizes the need to make assumptions about unknown parameters of the probe or the ice environment. The results indicate that currently used models do not yet reliably reproduce the performance of a probe under realistic conditions. Melting velocities and efficiencies are constantly overestimated by 15 to 50 \% in the models, but qualitatively agree with the field test data. Hence, losses are observed, that are not yet covered and quantified by the available loss models. We find that the deviation increases with decreasing ice temperature. We suspect that this mismatch is mainly due to the too restrictive idealization of the probe model and the fact that the probe was not operated in an efficiency-optimized manner during the field tests. With respect to space mission engineering, we find that performance and efficiency models must be used with caution in unknown ice environments, as various ice parameters have a significant effect on the melting process. Some of these are difficult to estimate from afar.}, language = {en} } @article{McArdellBarteltKowalski2007, author = {McArdell, Brian W. and Bartelt, Perry and Kowalski, Julia}, title = {Field observations of basal forces and fluid pore pressure in a debris flow}, series = {Geophysical Research Letters (GRL)}, volume = {34}, journal = {Geophysical Research Letters (GRL)}, number = {7}, isbn = {0094-8276}, year = {2007}, abstract = {Using results from an 8 m2 instrumented force plate we describe field measurements of normal and shear stresses, and fluid pore pressure for a debris flow. The flow depth increased from 0.1 to 1 m within the first 12 s of flow front arrival, remained relatively constant until 100 s, and then gradually decreased to 0.5 m by 600 s. Normal and shear stresses and pore fluid pressure varied in-phase with the flow depth. Calculated bulk densities are ρb = 2000-2250 kg m-3 for the bulk flow and ρf = 1600-1750 kg m-3 for the fluid phase. The ratio of effective normal stress to shear stress yields a Coulomb basal friction angle of ϕ = 26° at the flow front. We did not find a strong correlation between the degree of agitation in the flow, estimated using the signal from a geophone on the force plate, and an assumed dynamic pore fluid pressure. Our data support the idea that excess pore-fluid pressures are long lived in debris flows and therefore contribute to their unusual mobility.}, language = {en} } @article{MertensRoeger2000, author = {Mertens, Josef and R{\"o}ger, Wolf}, title = {F-Schlepp: Problem Taumelschwingung}, series = {Aerokurier. 44 (2000), H. 10}, journal = {Aerokurier. 44 (2000), H. 10}, isbn = {0341-1281}, pages = {73 -- 73}, year = {2000}, language = {de} } @article{Blome2004, author = {Blome, Hans-Joachim}, title = {Exploration des Weltalls. Raumfahrt und der Weg des Menschen in den Kosmos}, series = {Telepolis special. Wie Forscher und Raumfahrer Aliens aufsp{\"u}ren wollen}, journal = {Telepolis special. Wie Forscher und Raumfahrer Aliens aufsp{\"u}ren wollen}, publisher = {Heise Zeitschriften Verlag}, address = {Hannover}, year = {2004}, language = {de} } @article{GerhardtKrueger2000, author = {Gerhardt, Hans Joachim and Kr{\"u}ger, O.}, title = {Experimentelle Untersuchungen zur Entrauchung großer R{\"a}ume unter besonderer Beachtung des Windeinflusses}, series = {vfdb-Zeitschrift. 49 (2000), H. 2}, journal = {vfdb-Zeitschrift. 49 (2000), H. 2}, isbn = {0042-1804}, pages = {47 -- 54}, year = {2000}, language = {de} } @article{MertensHuenecke1988, author = {Mertens, Josef and H{\"u}necke, Klaus}, title = {Experimentelle Untersuchung zur Landeeigenschaft von Hyperschall-Flugger{\"a}ten / H{\"u}necke, Klaus ; Mertens, Josef}, series = {DGLR-Jahrbuch 1988 Bd. 1}, journal = {DGLR-Jahrbuch 1988 Bd. 1}, pages = {706}, year = {1988}, language = {de} } @article{BullerschenVoigtFriedrich1990, author = {Bullerschen, Klaus-Gerd and Voigt, H. and Friedrich, R.}, title = {Experimentelle und mathematische Untersuchungen zum Heißtransport von Stranggußbrammen}, series = {Stahl und Eisen. 110 (1990), H. 6}, journal = {Stahl und Eisen. 110 (1990), H. 6}, isbn = {0378-7559}, pages = {97 -- 105}, year = {1990}, language = {de} } @article{HavermannSalveTinetal.1994, author = {Havermann, Marc and Salve, M. de and Tin, G. del and Panella, B.}, title = {Experimental Study of the Temperature Field along a Density Lock / Salve, M. de ; Tin, G. del ; Panella, B. ; Sansoldo, D. ; Havermann, M.}, series = {Proceedings : International Conference on New Trends in Nuclear System Thermohydraulics, May 30th - June 2nd, 1994, Pisa / organized by Dipartimento di Costruzioni Meccaniche e Nucleari ... . Ed. by Francesco Oriolo}, journal = {Proceedings : International Conference on New Trends in Nuclear System Thermohydraulics, May 30th - June 2nd, 1994, Pisa / organized by Dipartimento di Costruzioni Meccaniche e Nucleari ... . Ed. by Francesco Oriolo}, publisher = {-}, address = {Pisa}, pages = {623 -- 630}, year = {1994}, language = {en} } @article{ReckerBosschaertsWagemakersetal.2010, author = {Recker, Elmar and Bosschaerts, Walter and Wagemakers, Rolf and Hendrick, Patrick and Funke, Harald and B{\"o}rner, Sebastian}, title = {Experimental study of a round jet in cross-flow at low momentum ratio}, series = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1}, journal = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1}, pages = {1 -- 13}, year = {2010}, language = {en} } @article{BohnFunke2003, author = {Bohn, Dieter and Funke, Harald}, title = {Experimental investigations into the nonuniform flow in a 4-stage turbine with special focus on the flow equalization in the first turbine stage}, series = {ASME TURBO EXPO, Proceedings of the ASME Turbo Expo, 2003}, journal = {ASME TURBO EXPO, Proceedings of the ASME Turbo Expo, 2003}, isbn = {0-7918-3689-4}, pages = {281 -- 289}, year = {2003}, language = {en} } @article{FunkeBoernerKrebsetal.2011, author = {Funke, Harald and B{\"o}rner, Sebastian and Krebs, W. and Wolf, E.}, title = {Experimental Characterization of Low NOx Micromix Prototype Combustors for Industrial Gas Turbine Applications}, series = {ASME Turbo Expo 2011 ; Vancouver, Canada, June 6-10, 2011}, journal = {ASME Turbo Expo 2011 ; Vancouver, Canada, June 6-10, 2011}, year = {2011}, language = {en} } @article{FunkeKeinzKustereretal.2016, author = {Funke, Harald and Keinz, Jan and Kusterer, Karsten and Ayed, Anis Haj and Kazari, Masahide and Kitajima, Junichi and Horikawa, Atsushi and Okada, Kunio}, title = {Experimental and Numerical Study on Optimizing the Dry Low NOₓ Micromix Hydrogen Combustion Principle for Industrial Gas Turbine Applications}, series = {Journal of Thermal Science and Engineering Applications}, volume = {9}, journal = {Journal of Thermal Science and Engineering Applications}, number = {2}, publisher = {ASME}, address = {New York, NY}, issn = {1948-5093}, doi = {10.1115/1.4034849}, pages = {021001 -- 021001-10}, year = {2016}, abstract = {Combined with the use of renewable energy sources for its production, hydrogen represents a possible alternative gas turbine fuel for future low-emission power generation. Due to the difference in the physical properties of hydrogen compared to other fuels such as natural gas, well-established gas turbine combustion systems cannot be directly applied to dry low NOₓ (DLN) hydrogen combustion. The DLN micromix combustion of hydrogen has been under development for many years, since it has the promise to significantly reduce NOₓ emissions. This combustion principle for air-breathing engines is based on crossflow mixing of air and gaseous hydrogen. Air and hydrogen react in multiple miniaturized diffusion-type flames with an inherent safety against flashback and with low NOₓ emissions due to a very short residence time of the reactants in the flame region. The paper presents an advanced DLN micromix hydrogen application. The experimental and numerical study shows a combustor configuration with a significantly reduced number of enlarged fuel injectors with high-thermal power output at constant energy density. Larger fuel injectors reduce manufacturing costs, are more robust and less sensitive to fuel contamination and blockage in industrial environments. The experimental and numerical results confirm the successful application of high-energy injectors, while the DLN micromix characteristics of the design point, under part-load conditions, and under off-design operation are maintained. Atmospheric test rig data on NOₓ emissions, optical flame-structure, and combustor material temperatures are compared to numerical simulations and show good agreement. The impact of the applied scaling and design laws on the miniaturized micromix flamelets is particularly investigated numerically for the resulting flow field, the flame-structure, and NOₓ formation.}, language = {en} } @article{FunkeDickhoffKeinzetal.2014, author = {Funke, Harald and Dickhoff, J. and Keinz, Jan and Anis, H. A. and Parente, A. and Hendrick, P.}, title = {Experimental and numerical study of the micromix combustion principle applied for hydrogen and hydrogen-rich syngas as fuel with increased energy density for industrial gas turbine applications}, series = {Energy procedia}, journal = {Energy procedia}, number = {61}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102 (E-Journal)}, doi = {10.1016/j.egypro.2014.12.201}, pages = {1736 -- 1739}, year = {2014}, abstract = {The Dry Low NOx (DLN) Micromix combustion principle with increased energy density is adapted for the industrial gas turbine APU GTCP 36-300 using hydrogen and hydrogen-rich syngas with a composition of 90\%-Vol. hydrogen (H₂) and 10\%-Vol. carbon-monoxide (CO). Experimental and numerical studies of several combustor geometries for hydrogen and syngas show the successful advance of the DLN Micromix combustion from pure hydrogen to hydrogen-rich syngas. The impact of the different fuel properties on the combustion principle and aerodynamic flame stabilization design laws, flow field, flame structure and emission characteristics is investigated by numerical analysis using a hybrid Eddy Break Up combustion model and validated against experimental results.}, language = {en} } @article{HajAyedKustererFunkeetal.2015, author = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.}, title = {Experimental and numerical investigations of the dry-low-NOx hydrogen micromix combustion chamber of an industrial gas turbine}, series = {Propulsion and power research}, volume = {Vol. 4}, journal = {Propulsion and power research}, number = {Iss. 3}, issn = {2212-540X}, doi = {10.1016/j.jppr.2015.07.005}, pages = {123 -- 131}, year = {2015}, language = {en} } @article{OlaruKowalskiSethietal.2012, author = {Olaru, Alexandra Maria and Kowalski, Julia and Sethi, Vaishali and Bl{\"u}mich, Bernhard}, title = {Exchange relaxometry of flow at small P{\´e}clet numbers in a glass bead pack}, series = {Journal of Magnetic Resonance (JMR)}, volume = {220}, journal = {Journal of Magnetic Resonance (JMR)}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1096-0856}, doi = {10.1016/j.jmr.2012.04.015}, pages = {32 -- 44}, year = {2012}, abstract = {In this paper we consider low P{\´e}clet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.}, language = {en} } @article{Dachwald2004, author = {Dachwald, Bernd}, title = {Evolutionary Neurocontrol: A Smart Method for Global Optimization of Low-Thrust Trajectories}, series = {22nd AIAA Applied Aerodynamics Conference and Exhibit - AIAA/AAS Astrodynamics Specialist Conference and Exhibit - AIAA Guidance, Navigation, and Control Conference and Exhibit - AIAA Modeling and Simulation Technologies Conference and Exhibit - AIAA Atmospheric Flight Mechanics Conference and Exhibit : 16 - 19 August 2004, Providence, Rhode Island / American Institute of Aeronautics and Astronautics. - (AIAA meeting papers on disc ; 2004,14-15)}, journal = {22nd AIAA Applied Aerodynamics Conference and Exhibit - AIAA/AAS Astrodynamics Specialist Conference and Exhibit - AIAA Guidance, Navigation, and Control Conference and Exhibit - AIAA Modeling and Simulation Technologies Conference and Exhibit - AIAA Atmospheric Flight Mechanics Conference and Exhibit : 16 - 19 August 2004, Providence, Rhode Island / American Institute of Aeronautics and Astronautics. - (AIAA meeting papers on disc ; 2004,14-15)}, publisher = {American Inst. of Aeronautics and Astronautics}, address = {Reston, Va.}, pages = {2 CD-ROMs}, year = {2004}, language = {en} } @article{DachwaldCarnelliVasile2009, author = {Dachwald, Bernd and Carnelli, Ian and Vasile, Massimiliano}, title = {Evolutionary Neurocontrol: A Novel Method for Low-Thrust Gravity-Assist Trajectory Optimization / Carnelli, Ian ; Dachwald, Bernd ; Vasile, Massimiliano}, series = {Journal of guidance control and dynamics. 32 (2009), H. 2}, journal = {Journal of guidance control and dynamics. 32 (2009), H. 2}, publisher = {AIAA}, address = {Reston, Va.}, isbn = {0731-5090}, pages = {616 -- 625}, year = {2009}, language = {en} } @article{DachwaldCarnelliVasile2006, author = {Dachwald, Bernd and Carnelli, I. and Vasile, M.}, title = {Evolutionary Neurocontrol as a Novel Method for Low-Thrust Gravity Assist Trajectory Optimization / I. Carnelli ; B. Dachwald ; M. Vasile}, series = {Proceedings of the Twenty-Fifth International Symposium on Space Technology and Science (Selected papers) : Kanazawa, [June 4 through June 11, 2006, at Kanazawa-shi Kanko Kaikan in Kanazawa city] / [Japan Society for Aeronautical and Space Sciences. Kohtaro Matsumoto [ed.-in-chief]}, journal = {Proceedings of the Twenty-Fifth International Symposium on Space Technology and Science (Selected papers) : Kanazawa, [June 4 through June 11, 2006, at Kanazawa-shi Kanko Kaikan in Kanazawa city] / [Japan Society for Aeronautical and Space Sciences. Kohtaro Matsumoto [ed.-in-chief]}, publisher = {JSASS}, address = {Tokyo}, isbn = {4-99005-002-9}, pages = {569 -- 574}, year = {2006}, language = {en} } @article{HoevelerJanserBindewaldetal.2015, author = {Hoeveler, Bastian and Janser, Frank and Bindewald, Thorsten and Gebhardt, Andreas}, title = {Entwurf, Fertigung und Untersuchung eines Windkanalmodells eines innovativen, senkrechtstartenden Kleinflugzeuges}, series = {RTejournal - Forum f{\"u}r Rapid Technologie}, journal = {RTejournal - Forum f{\"u}r Rapid Technologie}, number = {12}, publisher = {Fachhochschule Aachen}, address = {Aachen}, issn = {1614-0923}, url = {http://nbn-resolving.de/urn:nbn:de:0009-2-42921}, pages = {1 -- 5}, year = {2015}, language = {de} } @article{Dachwald1996, author = {Dachwald, Bernd}, title = {Entwicklung sicherer und wartbarer Software f{\"u}r den Eurofighter}, series = {Soldat und Technik : Strategie und Technik, Sicherheit (1996)}, journal = {Soldat und Technik : Strategie und Technik, Sicherheit (1996)}, isbn = {0038-0989}, pages = {663 -- 668}, year = {1996}, language = {de} } @article{Gerhardt2001, author = {Gerhardt, Hans Joachim}, title = {Entrauchungsnachweise. Kritische Diskussion von Methoden des Brandschutzingenieurwesens}, series = {vfdb-Zeitschrift. 50 (2001), H. 3}, journal = {vfdb-Zeitschrift. 50 (2001), H. 3}, isbn = {0042-1804}, pages = {99 -- 104}, year = {2001}, language = {de} } @article{GerhardtSchwarz2003, author = {Gerhardt, Hans Joachim and Schwarz, N.}, title = {Entrauchung {\"u}ber Seitenw{\"a}nde}, series = {vfdb-Zeitschrift. 52 (2003), H. 1}, journal = {vfdb-Zeitschrift. 52 (2003), H. 1}, isbn = {0042-1804}, pages = {25 -- 35}, year = {2003}, language = {de} } @article{GerhardtLieb2005, author = {Gerhardt, Hans Joachim and Lieb, R.-D.}, title = {Entrauchung komplexer R{\"a}umlichkeiten : Strategien und Steuerungen}, series = {T{\"u}r-Tor-Fenster-Report : Fachzeitschrift f{\"u}r die Technologien von T{\"u}ren, Toren und Fenstern. 25 (2005), H. 3}, journal = {T{\"u}r-Tor-Fenster-Report : Fachzeitschrift f{\"u}r die Technologien von T{\"u}ren, Toren und Fenstern. 25 (2005), H. 3}, isbn = {0724-7702}, pages = {27 -- 29}, year = {2005}, language = {de} } @article{TekinAshikagaHorikawaetal.2018, author = {Tekin, Nurettin and Ashikaga, Mitsugu and Horikawa, Atsushi and Funke, Harald}, title = {Enhancement of fuel flexibility of industrial gas turbines by development of innovative hydrogen combustion systems}, series = {Gas for energy}, journal = {Gas for energy}, number = {2}, publisher = {Vulkan-Verlag}, address = {Essen}, pages = {4}, year = {2018}, abstract = {For fuel flexibility enhancement hydrogen represents a possible alternative gas turbine fuel within future low emission power generation, in case of hydrogen production by the use of renewable energy sources such as wind energy or biomass. Kawasaki Heavy Industries, Ltd. (KHI) has research and development projects for future hydrogen society; production of hydrogen gas, refinement and liquefaction for transportation and storage, and utilization with gas turbine / gas engine for the generation of electricity. In the development of hydrogen gas turbines, a key technology is the stable and low NOx hydrogen combustion, especially Dry Low Emission (DLE) or Dry Low NOx (DLN) hydrogen combustion. Due to the large difference in the physical properties of hydrogen compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for DLE hydrogen combustion. Thus, the development of DLE hydrogen combustion technologies is an essential and challenging task for the future of hydrogen fueled gas turbines. The DLE Micro-Mix combustion principle for hydrogen fuel has been in development for many years to significantly reduce NOx emissions. This combustion principle is based on cross-flow mixing of air and gaseous hydrogen which reacts in multiple miniaturized "diffusion-type" flames. The major advantages of this combustion principle are the inherent safety against flashback and the low NOx-emissions due to a very short residence time of the reactants in the flame region of the micro-flames.}, language = {en} } @article{HavermannSeilerGeorgeetal.2002, author = {Havermann, Marc and Seiler, F. and George, A. and Leopold, F.}, title = {Enhanced Doppler Picture Velocimetry (DPV) for Planar Velocity Measurements in High-Speed Shock Tunnel Flow / Seiler, F. ; George, A. ; Leopold, F. ; Havermann, M. ; Srulijes, J.}, series = {10th International Symposium on Flow Visualization : Kyōto, Japan, August 26 - 29, 2002 / sponsored by International Flow Visualization Society . [Chairman:] Toshio Kobayashi}, journal = {10th International Symposium on Flow Visualization : Kyōto, Japan, August 26 - 29, 2002 / sponsored by International Flow Visualization Society . [Chairman:] Toshio Kobayashi}, publisher = {Visualization Society of Japan}, address = {Kyoto}, isbn = {4906497829}, year = {2002}, language = {en} } @article{DahlSuttrop1998, author = {Dahl, G{\"u}nter and Suttrop, F.}, title = {Engine control and low-NO(x) combustion for hydrogen fuelled aircraft gas turbines}, series = {International Journal of Hydrogen Energy. 23 (1998), H. 8}, journal = {International Journal of Hydrogen Energy. 23 (1998), H. 8}, isbn = {0360-3199}, pages = {695 -- 704}, year = {1998}, language = {en} } @article{PetersonRoethUibel2017, author = {Peterson, Leif Arne and R{\"o}th, Thilo and Uibel, Thomas}, title = {Einsatz von Holzwerkstoffen in Fahrzeugstrukturen}, series = {Bauen mit Holz}, journal = {Bauen mit Holz}, number = {3}, publisher = {Bruderverlag}, address = {K{\"o}ln}, issn = {0005-6545}, pages = {32 -- 38}, year = {2017}, language = {de} } @article{Mertens1999, author = {Mertens, Josef}, title = {Einige herausragende Ergebnisse des Technologieprogramms "Reduktion des Aerodynamischen Widerstands (RaWid)"}, series = {DGLR-Jahrbuch 1999 Bd. 3}, journal = {DGLR-Jahrbuch 1999 Bd. 3}, pages = {1461 -- 1468}, year = {1999}, language = {de} } @article{DahmannMager1994, author = {Dahmann, Peter and Mager, M.}, title = {Einfluß der Zusammensetzung der abzuscheidenden Verschmutzung auf die Abscheideleistung von Hydraulikfiltern}, series = {{\"O}lhydraulik und Pneumatik. 38 (1994), H. 4}, journal = {{\"O}lhydraulik und Pneumatik. 38 (1994), H. 4}, isbn = {0341-2660}, pages = {212 -- 214}, year = {1994}, language = {de} } @article{Blome1998, author = {Blome, Hans-Joachim}, title = {Eine Reise an die Grenzen von Raum und Zeit. Wie die Raumfahrt unser Bild vom Kosmos erweitert.}, series = {DLR- Nachrichten. Mitteilungen des Deutschen Zentrums f{\"u}r Luft- und Raumfahrt. 90 (1998)}, journal = {DLR- Nachrichten. Mitteilungen des Deutschen Zentrums f{\"u}r Luft- und Raumfahrt. 90 (1998)}, isbn = {0937-0420}, pages = {20 -- 29}, year = {1998}, language = {de} } @article{GerhardtSchoenwald2002, author = {Gerhardt, Hans Joachim and Sch{\"o}nwald, J.}, title = {Eine neue Brandsimulationsvorrichtung}, series = {vfdb-Zeitschrift. 51 (2002), H. 3}, journal = {vfdb-Zeitschrift. 51 (2002), H. 3}, isbn = {0042-1804}, pages = {91 -- 93}, year = {2002}, language = {de} } @article{Havermann2005, author = {Havermann, Marc}, title = {Effects of the shock tube open-end shape on vortex loops released from it / Kainuma, M. ; Havermann, M. ; Sun, M. ; Takayama, K.}, series = {Shock Waves : Proceedings of the 24th International Symposium on Shock Waves Beijing, China July 11-16, 2004 / edited by Z. Jiang}, journal = {Shock Waves : Proceedings of the 24th International Symposium on Shock Waves Beijing, China July 11-16, 2004 / edited by Z. Jiang}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-540-22497-6}, pages = {505 -- 510}, year = {2005}, language = {en} } @article{FischerKowalskiPudasainietal.2009, author = {Fischer, Jan-Thomas and Kowalski, Julia and Pudasaini, Shiva P. and Miller, S. A.}, title = {Dynamic Avalanche Modeling in Natural Terrain}, series = {International Snow Science Workshop, Davos 2009, Proceedings ; Proc. ISSW 2009}, journal = {International Snow Science Workshop, Davos 2009, Proceedings ; Proc. ISSW 2009}, pages = {448 -- 452}, year = {2009}, abstract = {The powerful avalanche simulation toolbox RAMMS (Rapid Mass Movements) is based on a depth-averaged hydrodynamic system of equations with a Voellmy-Salm friction relation. The two empirical friction parameters μ and � correspond to a dry Coulomb friction and a viscous resistance, respectively. Although μ and � lack a proper physical explanation, 60 years of acquired avalanche data in the Swiss Alps made a systematic calibration possible. RAMMS can therefore successfully model avalanche flow depth, velocities, impact pressure and run out distances. Pudasaini and Hutter (2003) have proposed extended, rigorously derived model equations that account for local curvature and twist. A coordinate transformation into a reference system, applied to the actual mountain topography of the natural avalanche path, is performed. The local curvature and the twist of the avalanche path induce an additional term in the overburden pressure. This leads to a modification of the Coulomb friction, the free-surface pressure gradient, the pressure induced by the channel, and the gravity components along and normal to the curved and twisted reference surface. This eventually guides the flow dynamics and deposits of avalanches. In the present study, we investigate the influence of curvature on avalanche flow in real mountain terrain. Simulations of real avalanche paths are performed and compared for the different models approaches. An algorithm to calculate curvature in real terrain is introduced in RAMMS. This leads to a curvature dependent friction relation in an extended version of the Voellmy-Salm model equations. Our analysis provides yet another step in interpreting the physical meaning and significance of the friction parameters used in the RAMMS computational environment.}, language = {en} } @article{PichlerGeorgeSeileretal.2009, author = {Pichler, A. and George, A. and Seiler, F. and Srulijes, J. and Havermann, Marc}, title = {Doppler Picture Velocimetry (DPV) applied to hypersonics}, series = {Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler}, journal = {Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-540-85168-4}, pages = {503 -- 508}, year = {2009}, language = {en} } @article{Schueckhaus2020, author = {Sch{\"u}ckhaus, Ulrich}, title = {Die SkyCab-Erfinder im WFMG-Interview}, series = {Business in MG}, journal = {Business in MG}, number = {1}, pages = {6 -- 7}, year = {2020}, language = {de} } @article{Blome2005, author = {Blome, Hans-Joachim}, title = {Die Entstehung des Kosmos - Vom Anfang der Welt bis zum komplexen Universum}, series = {Homo spaciens - der Mensch im Kosmos : ein interdisziplin{\"a}rer Ausblick auf Ursprung und Zukunft des Menschen im All ; Berichtsband der Tagung "Mensch im Kosmos IV" vom 14. - 16.10.2004 auf Schloß Theuern/Oberpfalz / P. R. Sahm, ... Hans-Joachim Blome(Hrsg.)}, journal = {Homo spaciens - der Mensch im Kosmos : ein interdisziplin{\"a}rer Ausblick auf Ursprung und Zukunft des Menschen im All ; Berichtsband der Tagung "Mensch im Kosmos IV" vom 14. - 16.10.2004 auf Schloß Theuern/Oberpfalz / P. R. Sahm, ... Hans-Joachim Blome(Hrsg.)}, publisher = {Discorsi}, address = {Hamburg}, isbn = {3-9807330-8-4}, pages = {XVIII, 331 S. : Ill., graph. Darst., Kt.}, year = {2005}, language = {de} } @article{Gerhardt1998, author = {Gerhardt, Hans Joachim}, title = {Die Bestimmung der Windbelastung von Bauwerken im Windkanal}, series = {Der Pr{\"u}fingenieur (1998)}, journal = {Der Pr{\"u}fingenieur (1998)}, pages = {31 -- 45}, year = {1998}, language = {de} } @article{HailerWeberNevelingetal.2020, author = {Hailer, Benjamin and Weber, Tobias and Neveling, Sebastian and Dera, Samuel and Arent, Jan-Christoph and Middendorf, Peter}, title = {Development of a test device to determine the frictional behavior between honeycomb and prepreg layers under realistic manufacturing conditions}, series = {Journal of Sandwich Structures \& Materials}, journal = {Journal of Sandwich Structures \& Materials}, number = {Volume 23, Issue 7}, publisher = {Sage}, address = {London}, issn = {1530-7972}, doi = {10.1177/1099636220923986}, pages = {3017 -- 3043}, year = {2020}, abstract = {In the friction tests between honeycomb with film adhesive and prepreg, the relative displacement occurs between the film adhesive and the prepreg. The film adhesive does not shift relative to the honeycomb. This is consistent with the core crush behavior where the honeycomb moves together with the film adhesive, as can be seen in Figure 2(a). The pull-through forces of the friction measurements between honeycomb and prepreg at 1 mm deformation are plotted in Figure 17(a). While the friction at 100°C is similar to the friction at 120°C, it decreases significantly at 130°C and exhibits a minimum at 140°C. At 150°C, the friction rises again slightly and then sharply at 160°C. Since the viscosity of the M18/1 prepreg resin drops significantly before it cures [23], the minimum friction at 140°C could result from a minimum viscosity of the mixture of prepreg resin and film adhesive before the bond subsequently cures. Figure 17(b) shows the mean value curve of the friction measurements at 140°C. The error bars, which represent the standard deviation, reveal the good repeatability of the tests. The force curve is approximately horizontal between 1 mm and 2 mm. The friction then slightly rises. As with interlaminar friction measurements, this could be due to the fact that resin is removed by friction and the proportion of boundary lubrication increases. Figure 18 shows the surfaces after the friction measurement. The honeycomb cell walls are clearly visible in the film adhesive. There are areas where the film adhesive is completely removed and the carrier material of the film adhesive becomes visible. In addition, the viscosity of the resin changes as the curing progresses during the friction test. This can also affect the force-displacement curve.}, language = {en} } @article{FunkeRobinson2007, author = {Funke, Harald and Robinson, A. E.}, title = {Development of a new test rig for a micro scale hydrogen combustion chamber}, series = {Proceedings of the 2nd European Conference for Aero-Space Sciences : July 1 - 6, 2007, Brussels, Belgium}, journal = {Proceedings of the 2nd European Conference for Aero-Space Sciences : July 1 - 6, 2007, Brussels, Belgium}, publisher = {-}, pages = {1 -- 8}, year = {2007}, language = {en} } @article{RobinsonFunkeHendricketal.2008, author = {Robinson, A. E. and Funke, Harald and Hendrick, P. and Recker, E. and Peirs, J.}, title = {Development of a hydrogen fuelled 1 kW ultra micro gas turbine with special respect to designing, testing and mapping of the µ-scale combustor}, series = {IEEE International Conference on Sustainable Energy Technologies, 2008 : ICSET 2008 ; Singapore, 24 - 27 Nov. 2008.}, journal = {IEEE International Conference on Sustainable Energy Technologies, 2008 : ICSET 2008 ; Singapore, 24 - 27 Nov. 2008.}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4244-1887-9}, pages = {656 -- 660}, year = {2008}, language = {en} } @article{TrillaGrossenRobinsonetal.2008, author = {Trilla, Joan and Grossen, J{\"u}rgen and Robinson, Alexander and Funke, Harald and Bosschaerts, Walter and Hendrick, Patrick}, title = {Development of a hydrogen combustion chamber for an ultra micro gas turbine}, series = {PowerMEMS 2008, 8th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications, microEMS 2008, 2nd Symposium on Micro Environmental Machine Systems, Sendai, JP, Nov 9-12, 2008}, journal = {PowerMEMS 2008, 8th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications, microEMS 2008, 2nd Symposium on Micro Environmental Machine Systems, Sendai, JP, Nov 9-12, 2008}, pages = {101 -- 104}, year = {2008}, language = {en} } @article{SeifarthGossmannGrosseetal.2015, author = {Seifarth, Volker and Goßmann, Matthias and Grosse, J. O. and Becker, C. and Heschel, I. and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l}, title = {Development of a Bioreactor to Culture Tissue Engineered Ureters Based on the Application of Tubular OPTIMAIX 3D Scaffolds}, series = {Urologia Internationalis}, volume = {2015}, journal = {Urologia Internationalis}, number = {95}, publisher = {Karger}, address = {Basel}, issn = {0042-1138}, doi = {10.1159/000368419}, pages = {106 -- 113}, year = {2015}, language = {en} } @article{FunkeKeinzKustereretal.2017, author = {Funke, Harald and Keinz, Jan and Kusterer, K. and Haj Ayed, A. and Kazari, M. and Kitajima, J. and Horikawa, A. and Okada, K.}, title = {Development and Testing of a Low NOX Micromix Combustion Chamber for an Industrial Gas Turbine}, series = {International Journal of Gas Turbine, Propulsion and Power Systems}, volume = {9}, journal = {International Journal of Gas Turbine, Propulsion and Power Systems}, number = {1}, issn = {1882-5079}, doi = {10.38036/jgpp.9.1_27}, pages = {27 -- 36}, year = {2017}, abstract = {The Micromix combustion principle, based on cross-flow mixing of air and hydrogen, promises low emission applications in future gas turbines. The Micromix combustion takes place in several hundreds of miniaturized diffusion-type micro-flames. The major advantage is the inherent safety against flash-back and low NOx-emissions due to a very short residence time of reactants in the flame region. The paper gives insight into the Micromix design and scaling procedure for different energy densities and the interaction of scaling laws and key design drivers in gas turbine integration. Numerical studies, experimental testing, gas turbine integration and interface considerations are evaluated. The aerodynamic stabilization of the miniaturized flamelets and the resulting flow field, flame structure and NOx formation are analysed experimentally and numerically. The results show and confirm the successful adaption of the low NOx Micromix characteristics for a range of different nozzle sizes, energy densities and thermal power output.}, language = {de} } @article{FunkeRoennaRobinson2008, author = {Funke, Harald and R{\"o}nna, Uwe and Robinson, A. E.}, title = {Development and testing of a 10 kW diffusive micromix combustor for hydrogen-fuelled μ-scale gas turbines}, series = {Proceedings of ASME Turbo Expo 2008: Power for Land, Sea and Air ; GT2008 ; June 9-13, 2008, Berlin, Germany}, journal = {Proceedings of ASME Turbo Expo 2008: Power for Land, Sea and Air ; GT2008 ; June 9-13, 2008, Berlin, Germany}, publisher = {ASME}, address = {New York, NY}, pages = {1 -- 8}, year = {2008}, language = {en} } @article{KraemerDaabMuelleretal.2013, author = {Kr{\"a}mer, Stefan and Daab, Dominique Jonas and M{\"u}ller, Brigitte and Wagner, Tobias and Baader, Fabian and Hessel, Joana and Gdalewitsch, Georg and Plescher, Engelbert and Dachwald, Bernd and Wahle, Michael and Gierse, Andreas and Vetter, Rudolf and Pf{\"u}tzenreuter, Lysan}, title = {Development and flight-testing of a system to isolate vibrations for microgravity experiments on sounding rockets}, series = {21st ESA Symposium on Rocket and Balloon Research}, journal = {21st ESA Symposium on Rocket and Balloon Research}, pages = {1 -- 8}, year = {2013}, language = {en} } @article{BindalSharmaJanseretal.2013, author = {Bindal, Gaurav and Sharma, Sparsh and Janser, Frank and Neu, Eugen}, title = {Detailed analysis of variables affecting wing kinematics of bat flight}, series = {SAE International Journal of Aerospace}, volume = {6}, journal = {SAE International Journal of Aerospace}, number = {2}, issn = {1946-3901}, doi = {10.4271/2013-01-9003}, pages = {811 -- 818}, year = {2013}, language = {en} } @article{Gerhardt2005, author = {Gerhardt, Hans Joachim}, title = {Design methods of smoke and heat exhaust systems in construction works}, series = {V Mie\&\#796;dzynarodowa Konferencja Bezpiecze\&\#324;stwo Po\&\#380;arowe Budowli, Warszawa-Miedzeszyn, 14 - 16 listopada 2005 r. = : Vth International Conference Fire Safety of Buildings / ITB ... [Ed. Miros\&\#322;aw Kosiorek]}, journal = {V Mie\&\#796;dzynarodowa Konferencja Bezpiecze\&\#324;stwo Po\&\#380;arowe Budowli, Warszawa-Miedzeszyn, 14 - 16 listopada 2005 r. = : Vth International Conference Fire Safety of Buildings / ITB ... [Ed. Miros\&\#322;aw Kosiorek]}, publisher = {ITB}, address = {Warszawa}, isbn = {83-7413-810-6}, pages = {127 -- 140}, year = {2005}, language = {en} } @article{FunkeRobinsonHendricketal.2010, author = {Funke, Harald and Robinson, A. E. and Hendrick, P. and Wagemakers, R.}, title = {Design and Testing of a Micromix Combustor With Recuperative Wall Cooling for a Hydrogen Fuelled µ-Scale Gas Turbine}, series = {Proceedings of the ASME Turbo Expo 2010 : presented at the 2010 ASME Turbo Expo, June 14 - 18, 2010, Glasgow, UK / sponsored by the International Gas Turbine Institute / Vol. 5: Industrial and cogeneration ; microturbines and small turbomachinery ; oil and gas applications ; wind turbine technology}, journal = {Proceedings of the ASME Turbo Expo 2010 : presented at the 2010 ASME Turbo Expo, June 14 - 18, 2010, Glasgow, UK / sponsored by the International Gas Turbine Institute / Vol. 5: Industrial and cogeneration ; microturbines and small turbomachinery ; oil and gas applications ; wind turbine technology}, publisher = {ASME}, address = {New York, NY}, isbn = {978-0-7918-4400-7}, pages = {587 -- 596}, year = {2010}, language = {en} } @article{RobinsonFunkeHendrick2011, author = {Robinson, A. E. and Funke, Harald and Hendrick, P.}, title = {Design and Testing of a Micromix Combustor With Recuperative Wall Cooling for a Hydrogen Fueled µ-Scale Gas Turbine}, series = {Journal of engineering for gas turbines and power}, volume = {133}, journal = {Journal of engineering for gas turbines and power}, number = {8}, publisher = {ASME}, address = {New York}, isbn = {1528-8919}, pages = {Art. Nr. 082301 , 8 Seiten}, year = {2011}, language = {en} } @article{SchmitzDamannSchmit1984, author = {Schmitz, G{\"u}nter and Damann, H. and Schmit, H. J.}, title = {Design and Analysis of a Waveguide Isolator with a Form-Birefringent Top Layer}, series = {ECOC '84 : Conference proceedings ; 10th European Conference on Optical Communication, September 3 - 6, 1984 Liederhalle Stuttgart, Federal Republic of Germany / Organized by Nachrichtentechn. Ges. im VDE (NTG).}, journal = {ECOC '84 : Conference proceedings ; 10th European Conference on Optical Communication, September 3 - 6, 1984 Liederhalle Stuttgart, Federal Republic of Germany / Organized by Nachrichtentechn. Ges. im VDE (NTG).}, publisher = {VDE-Verl.}, address = {Berlin [u.a.]}, isbn = {3-8007-1383-7}, pages = {42}, year = {1984}, language = {en} } @article{EschSalberKemperetal.2001, author = {Esch, Thomas and Salber, W. and Kemper, Hans and Staay, F. van der}, title = {Der elektromechanische Ventiltrieb - Systembaustein f{\"u}r zuk{\"u}nftige Antriebskonzepte, Teil 2.}, series = {Motortechnische Zeitschrift (MTZ).}, volume = {62}, journal = {Motortechnische Zeitschrift (MTZ).}, number = {1}, publisher = {Springer Nature}, address = {Basel}, issn = {0024-8525}, doi = {10.1007/bf03227081}, pages = {44 -- 55}, year = {2001}, language = {de} } @article{EschSalberKemperetal.2000, author = {Esch, Thomas and Salber, W. and Kemper, Hans and Staay, F. van der}, title = {Der elektromechanische Ventiltrieb - Systembaustein f{\"u}r zuk{\"u}nftige Antriebskonzepte, Teil 1.}, series = {Motortechnische Zeitschrift (MTZ).}, volume = {61}, journal = {Motortechnische Zeitschrift (MTZ).}, number = {12}, publisher = {Springer Nature}, address = {Basel}, issn = {0024-8525}, doi = {10.1007/bf03227081}, pages = {826 -- 836}, year = {2000}, language = {de} } @article{WittmannKehrWillnecker2000, author = {Wittmann, Klaus and Kehr, J. and Willnecker, R.}, title = {Decentralized Payload Operations Concept for Columbus}, year = {2000}, language = {en} } @article{Blome1989, author = {Blome, Hans-Joachim}, title = {Das Quantenvakuum und die kosmologische Konstante}, series = {Physikalische Bl{\"a}tter. 45 (1989)}, journal = {Physikalische Bl{\"a}tter. 45 (1989)}, isbn = {0342-4472}, pages = {51 -- 56}, year = {1989}, language = {de} } @article{GerhardtKonrathLieb2005, author = {Gerhardt, Hans Joachim and Konrath, B. and Lieb, R.-D.}, title = {Das Drallrohr}, series = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik. 56 (2005), H. 11}, journal = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik. 56 (2005), H. 11}, isbn = {1436-5103}, pages = {91 -- 95}, year = {2005}, language = {en} } @article{HavermannSeilerGeorgesetal.2002, author = {Havermann, Marc and Seiler, F. and Georges, A. and Leopold, F.}, title = {Das Dopplerbildverfahren (DPV) des ISL zur Messung der Str{\"o}mungsgeschwindigkeit in einer Ebene / Seiler, F. ; Georges, A. ; Leopold, F. ; Srulijes, J. ; Havermann, M.}, series = {Lasermethoden in der Str{\"o}mungsmesstechnik, 10. Fachtagung, Deutsche Gesellschaft f{\"u}r Laser-Anemometrie GALA, Rostock, DE, 10.-12. Sep, 2002}, journal = {Lasermethoden in der Str{\"o}mungsmesstechnik, 10. Fachtagung, Deutsche Gesellschaft f{\"u}r Laser-Anemometrie GALA, Rostock, DE, 10.-12. Sep, 2002}, publisher = {Univ.}, address = {Rostock}, isbn = {3-86009-233-2}, pages = {11.1 -- 11.6}, year = {2002}, language = {de} } @article{SchuellerKowalskiRaback2016, author = {Sch{\"u}ller, K. and Kowalski, Julia and Raback, P.}, title = {Curvilinear melting - A preliminary experimental and numerical study}, series = {International Journal of Heat and Mass Transfer}, journal = {International Journal of Heat and Mass Transfer}, number = {92}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0017-9310}, doi = {10.1016/j.ijheatmasstransfer.2015.09.046}, pages = {884 -- 892}, year = {2016}, abstract = {When exploring glacier ice it is often necessary to take samples or implement sensors at a certain depth underneath the glacier surface. One way of doing this is by using heated melting probes. In their common form these devices experience a straight one-dimensional downwards motion and can be modeled by standard close-contact melting theory. A recently developed melting probe however, the IceMole, achieves maneuverability by simultaneously applying a surface temperature gradient to induce a change in melting direction and controlling the effective contact-force by means of an ice screw to stabilize its change in attitude. A modeling framework for forced curvilinear melting does not exist so far and will be the content of this paper. At first, we will extend the existing theory for quasi-stationary close-contact melting to curved trajectories. We do this by introducing a rotational mode. This additional unknown in the system implies yet the need for another model closure. Within this new framework we will focus on the effect of a variable contact-force as well as different surface temperature profiles. In order to solve for melting velocity and curvature of the melting path we present both an inverse solution strategy for the analytical model, and a more general finite element framework implemented into the open source software package ELMER. Model results are discussed and compared to experimental data conducted in laboratory tests.}, language = {de} } @article{BullerschenWilhelmi1991, author = {Bullerschen, Klaus-Gerd and Wilhelmi, Herbert}, title = {Cooling of arc furnace electrodes with heat pipes}, series = {Chemical Engineering \& Technology. 14 (1991), H. 1}, journal = {Chemical Engineering \& Technology. 14 (1991), H. 1}, isbn = {0930-7516}, pages = {45 -- 53}, year = {1991}, language = {en} } @article{BoernerFunkeHendricketal.2010, author = {B{\"o}rner, Sebastian and Funke, Harald and Hendrick, P. and Recker, E.}, title = {Control system modifications for a hydrogen fuelled gas-turbine}, series = {ISROMAC 13, 13th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, Honolulu, HI, US, Apr 4-7, 2010}, journal = {ISROMAC 13, 13th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, Honolulu, HI, US, Apr 4-7, 2010}, publisher = {Curran}, address = {Red Hook, NY}, isbn = {978-1-617-38848-4}, pages = {665 -- 670}, year = {2010}, language = {en} } @article{FunkeBoernerFalketal.2011, author = {Funke, Harald and B{\"o}rner, Sebastian and Falk, F. and Hendrick, P.}, title = {Control system modifications and their effects on the operation of a hydrogen-fueled Auxiliary Power Unit}, series = {XX international symposium on air breathing engines 2011 : ISABE 2011, Gothenburg, Sweden, 12-16 September, 2011. Vol. 2.}, journal = {XX international symposium on air breathing engines 2011 : ISABE 2011, Gothenburg, Sweden, 12-16 September, 2011. Vol. 2.}, publisher = {American Institute of Aeronautics and Astronautics}, address = {Reston, VA}, isbn = {9781618391803}, pages = {929 -- 938}, year = {2011}, language = {en} } @article{LeyPlescherScholzetal.2007, author = {Ley, Wilfried and Plescher, Engelbert and Scholz, Artur and Piepenbrock, Johannes}, title = {COMPASS-1 picosatellite project / Ley, Wilfried ; Plescher, Engelbert ; Scholz, Artur ; Piepenbrock, Johannes}, series = {Small satellites for earth observation : digest of the 6th International symposium of the International Academy of Astronautics, Berlin, April 23 - 26, 2007 / ed. by Rainer Sandau; Hans-Peter R{\"o}ser; Arnoldo Valenzuela}, journal = {Small satellites for earth observation : digest of the 6th International symposium of the International Academy of Astronautics, Berlin, April 23 - 26, 2007 / ed. by Rainer Sandau; Hans-Peter R{\"o}ser; Arnoldo Valenzuela}, publisher = {Wissenschaft und Technik Verl.}, address = {Berlin}, isbn = {9783896855718}, pages = {147 -- 150}, year = {2007}, language = {en} } @article{KochBoehnischVerdoncketal.2024, author = {Koch, Christopher and B{\"o}hnisch, Nils and Verdonck, Hendrik and Hach, Oliver and Braun, Carsten}, title = {Comparison of unsteady low- and mid-fidelity propeller aerodynamic methods for whirl flutter applications}, series = {Applied Sciences}, volume = {14}, journal = {Applied Sciences}, number = {2}, publisher = {MDPI}, address = {Basel}, issn = {2076-3417}, doi = {10.3390/app14020850}, pages = {1 -- 28}, year = {2024}, abstract = {Aircraft configurations with propellers have been drawing more attention in recent times, partly due to new propulsion concepts based on hydrogen fuel cells and electric motors. These configurations are prone to whirl flutter, which is an aeroelastic instability affecting airframes with elastically supported propellers. It commonly needs to be mitigated already during the design phase of such configurations, requiring, among other things, unsteady aerodynamic transfer functions for the propeller. However, no comprehensive assessment of unsteady propeller aerodynamics for aeroelastic analysis is available in the literature. This paper provides a detailed comparison of nine different low- to mid-fidelity aerodynamic methods, demonstrating their impact on linear, unsteady aerodynamics, as well as whirl flutter stability prediction. Quasi-steady and unsteady methods for blade lift with or without coupling to blade element momentum theory are evaluated and compared to mid-fidelity potential flow solvers (UPM and DUST) and classical, derivative-based methods. Time-domain identification of frequency-domain transfer functions for the unsteady propeller hub loads is used to compare the different methods. Predictions of the minimum required pylon stiffness for stability show good agreement among the mid-fidelity methods. The differences in the stability predictions for the low-fidelity methods are higher. Most methods studied yield a more unstable system than classical, derivative-based whirl flutter analysis, indicating that the use of more sophisticated aerodynamic modeling techniques might be required for accurate whirl flutter prediction.}, language = {en} } @article{FunkeBeckmannKeinzetal.2016, author = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester}, title = {Comparison of Numerical Combustion Models for Hydrogen and Hydrogen-Rich Syngas Applied for Dry-Low-NOx-Micromix-Combustion}, series = {ASME Turbo Expo 2016: Turbomachinery Technical Conference and Exposition Volume 4A: Combustion, Fuels and Emissions Seoul, South Korea, June 13-17, 2016}, journal = {ASME Turbo Expo 2016: Turbomachinery Technical Conference and Exposition Volume 4A: Combustion, Fuels and Emissions Seoul, South Korea, June 13-17, 2016}, publisher = {ASME}, address = {New York, NY}, isbn = {978-0-7918-4975-0}, doi = {10.1115/GT2016-56430}, pages = {12}, year = {2016}, abstract = {The Dry-Low-NOₓ (DLN) Micromix combustion technology has been developed as low emission combustion principle for industrial gas turbines fueled with hydrogen or syngas. The combustion process is based on the phenomenon of jet-in-crossflow-mixing. Fuel is injected perpendicular into the air-cross-flow and burned in a multitude of miniaturized, diffusion-like flames. The miniaturization of the flames leads to a significant reduction of NOₓ emissions due to the very short residence time of reactants in the flame. In the Micromix research approach, CFD analyses are validated towards experimental results. The combination of numerical and experimental methods allows an efficient design and optimization of DLN Micromix combustors concerning combustion stability and low NOₓ emissions. The paper presents a comparison of several numerical combustion models for hydrogen and hydrogen-rich syngas. They differ in the complexity of the underlying reaction mechanism and the associated computational effort. For pure hydrogen combustion a one-step global reaction is applied using a hybrid Eddy-Break-up model that incorporates finite rate kinetics. The model is evaluated and compared to a detailed hydrogen combustion mechanism derived by Li et al. including 9 species and 19 reversible elementary reactions. Based on this mechanism, reduction of the computational effort is achieved by applying the Flamelet Generated Manifolds (FGM) method while the accuracy of the detailed reaction scheme is maintained. For hydrogen-rich syngas combustion (H₂-CO) numerical analyses based on a skeletal H₂/CO reaction mechanism derived by Hawkes et al. and a detailed reaction mechanism provided by Ranzi et al. are performed. The comparison between combustion models and the validation of numerical results is based on exhaust gas compositions available from experimental investigation on DLN Micromix combustors. The conducted evaluation confirms that the applied detailed combustion mechanisms are able to predict the general physics of the DLN-Micromix combustion process accurately. The Flamelet Generated Manifolds method proved to be generally suitable to reduce the computational effort while maintaining the accuracy of detailed chemistry. Especially for reaction mechanisms with a high number of species accuracy and computational effort can be balanced using the FGM model.}, language = {en} } @article{FunkeBeckmannKeinzetal.2018, author = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester}, title = {Comparison of Numerical Combustion Models for Hydrogen and Hydrogen-Rich Syngas Applied for Dry-Low-Nox-Micromix-Combustion}, series = {Journal of Engineering for Gas Turbines and Power}, volume = {140}, journal = {Journal of Engineering for Gas Turbines and Power}, number = {8}, publisher = {ASME}, address = {New York, NY}, issn = {0742-4795}, doi = {10.1115/1.4038882}, pages = {9 Seiten}, year = {2018}, abstract = {The Dry-Low-NOx (DLN) Micromix combustion technology has been developed as low emission combustion principle for industrial gas turbines fueled with hydrogen or syngas. The combustion process is based on the phenomenon of jet-in-crossflow-mixing (JICF). Fuel is injected perpendicular into the air-cross-flow and burned in a multitude of miniaturized, diffusion-like flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. In the Micromix research approach, computational fluid dynamics (CFD) analyses are validated toward experimental results. The combination of numerical and experimental methods allows an efficient design and optimization of DLN Micromix combustors concerning combustion stability and low NOx emissions. The paper presents a comparison of several numerical combustion models for hydrogen and hydrogen-rich syngas. They differ in the complexity of the underlying reaction mechanism and the associated computational effort. The performance of a hybrid eddy-break-up (EBU) model with a one-step global reaction is compared to a complex chemistry model and a flamelet generated manifolds (FGM) model, both using detailed reaction schemes for hydrogen or syngas combustion. Validation of numerical results is based on exhaust gas compositions available from experimental investigation on DLN Micromix combustors. The conducted evaluation confirms that the applied detailed combustion mechanisms are able to predict the general physics of the DLN-Micromix combustion process accurately. The FGM method proved to be generally suitable to reduce the computational effort while maintaining the accuracy of detailed chemistry.}, language = {en} } @article{FingerBraunBil2020, author = {Finger, Felix and Braun, Carsten and Bil, Cees}, title = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft}, series = {Journal of Aircraft}, volume = {57}, journal = {Journal of Aircraft}, number = {5}, publisher = {AIAA}, address = {Reston, Va.}, issn = {1533-3868}, doi = {10.2514/1.C035897}, year = {2020}, abstract = {Until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial hybrid-electric, parallel hybrid-electric, fully electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This Paper provides insight into some factors that drive a new design toward either conventional or hybrid propulsion systems. General aviation aircraft, regional transport aircraft vertical takeoff and landing air taxis, and unmanned aerial vehicles are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their takeoff mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Only parallel-hybrid-electric powertrains are taken into account. Aeropropulsive interaction effects are neglected. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints. However, if the propulsion system is sized by a continuous power requirement, hybrid-electric systems offer hardly any benefit.}, language = {en} } @article{HavermannBeylich1998, author = {Havermann, Marc and Beylich, A. E.}, title = {Combined Measurement of Velocity, Temperature and Pressure in Compressible Gas Flows Using Laser-Induced Iodine Fluorescence / Havermann, M. ; Beylich, A. E.}, publisher = {-}, year = {1998}, language = {en} } @article{MeyerGranrathFeyerletal.2021, author = {Meyer, Max-Arno and Granrath, Christian and Feyerl, G{\"u}nter and Richenhagen, Johannes and Kaths, Jakob and Andert, Jakob}, title = {Closed-loop platoon simulation with cooperative intelligent transportation systems based on vehicle-to-X communication}, series = {Simulation Modelling Practice and Theory}, volume = {106}, journal = {Simulation Modelling Practice and Theory}, number = {Art. 102173}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1569-190X}, doi = {10.1016/j.simpat.2020.102173}, year = {2021}, language = {en} } @article{Mertens1985, author = {Mertens, Josef}, title = {Charakteristiken des Staub-Gas-Gemisches}, series = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4}, journal = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4}, isbn = {1521-4001}, pages = {T211 -- T213}, year = {1985}, language = {de} } @article{AyedKustererFunkeetal.2016, author = {Ayed, Anis Haj and Kusterer, Karsten and Funke, Harald and Keinz, Jan}, title = {CFD Based Improvement of the DLN Hydrogen Micromix Combustion Technology at Increased Energy Densities}, series = {American Scientific Research Journal for Engineering, Technology, and Sciences (ASRJETS)}, volume = {26}, journal = {American Scientific Research Journal for Engineering, Technology, and Sciences (ASRJETS)}, number = {3}, publisher = {GSSRR}, issn = {2313-4402}, pages = {290 -- 303}, year = {2016}, abstract = {Combined with the use of renewable energy sources for its production, Hydrogen represents a possible alternative gas turbine fuel within future low emission power generation. Due to the large difference in the physical properties of Hydrogen compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for Dry Low NOx (DLN) Hydrogen combustion. Thus, the development of DLN combustion technologies is an essential and challenging task for the future of Hydrogen fuelled gas turbines. The DLN Micromix combustion principle for hydrogen fuel has been developed to significantly reduce NOx-emissions. This combustion principle is based on cross-flow mixing of air and gaseous hydrogen which reacts in multiple miniaturized diffusion-type flames. The major advantages of this combustion principle are the inherent safety against flash-back and the low NOx-emissions due to a very short residence time of reactants in the flame region of the micro-flames. The Micromix Combustion technology has been already proven experimentally and numerically for pure Hydrogen fuel operation at different energy density levels. The aim of the present study is to analyze the influence of different geometry parameter variations on the flame structure and the NOx emission and to identify the most relevant design parameters, aiming to provide a physical understanding of the Micromix flame sensitivity to the burner design and identify further optimization potential of this innovative combustion technology while increasing its energy density and making it mature enough for real gas turbine application. The study reveals great optimization potential of the Micromix Combustion technology with respect to the DLN characteristics and gives insight into the impact of geometry modifications on flame structure and NOx emission. This allows to further increase the energy density of the Micromix burners and to integrate this technology in industrial gas turbines.}, language = {en} } @article{AyedKustererFunkeetal.2017, author = {Ayed, Anis Haj and Kusterer, Karsten and Funke, Harald and Keinz, Jan and Bohn, D.}, title = {CFD based exploration of the dry-low-NOx hydrogen micromix combustion technology at increased energy densities}, series = {Propulsion and Power Research}, volume = {6}, journal = {Propulsion and Power Research}, number = {1}, publisher = {Elsevier}, address = {Amsterdam}, isbn = {2212-540X}, doi = {10.1016/j.jppr.2017.01.005}, pages = {15 -- 24}, year = {2017}, language = {en} } @article{JanThimoBauerBieleetal.2019, author = {Jan Thimo, Grundmann and Bauer, Waldemar and Biele, Jens and Boden, Ralf and Ceriotti, Matteo and Cordero, Federico and Dachwald, Bernd and Dumont, Etienne and Grimm, Christian D. and Hercik, David}, title = {Capabilities of Gossamer-1 derived small spacecraft solar sails carrying Mascot-derived nanolanders for in-situ surveying of NEAs}, series = {Acta Astronautica}, volume = {156}, journal = {Acta Astronautica}, number = {3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0094-5765}, doi = {10.1016/j.actaastro.2018.03.019}, pages = {330 -- 362}, year = {2019}, language = {en} }