@article{KobFrauenrath2009, author = {Kob, Malte and Frauenrath, Tobias}, title = {A system for parallel measurement of glottis opening and larynx position}, series = {Biomedical Signal Processing and Control}, volume = {4}, journal = {Biomedical Signal Processing and Control}, number = {3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1746-8108}, doi = {10.1016/j.bspc.2009.03.004}, pages = {221 -- 228}, year = {2009}, abstract = {The simultaneous assessment of glottal dynamics and larynx position can be beneficial for the diagnosis of disordered voice or speech production and swallowing. Up to now, methods either concentrate on assessment of the glottis opening using optical, acoustical or electrical (electroglottography, EGG) methods, or on visualisation of the larynx position using ultrasound, computer tomography or magnetic resonance imaging techniques. The method presented here makes use of a time-multiplex measurement approach of space-resolved transfer impedances through the larynx. The fast sequence of measurements allows a quasi simultaneous assessment of both larynx position and EGG signal using up to 32 transmit-receive signal paths. The system assesses the dynamic opening status of the glottis as well as the vertical and back/forward motion of the larynx. Two electrode-arrays are used for the measurement of the electrical transfer impedance through the neck in different directions. From the acquired data the global and individual conductivity is calculated as well as a 2D point spatial representation of the minimum impedance. The position information is shown together with classical EGG signals allowing a synchronous visual assessment of glottal area and larynx position. A first application to singing voice analysis is presented that indicate a high potential of the method for use as a non-invasive tool in the diagnosis of voice, speech, and swallowing disorders.}, language = {en} } @inproceedings{EltesterFerreinSchiffer2020, author = {Eltester, Niklas Sebastian and Ferrein, Alexander and Schiffer, Stefan}, title = {A smart factory setup based on the RoboCup logistics league}, series = {2020 IEEE Conference on Industrial Cyberphysical Systems (ICPS)}, booktitle = {2020 IEEE Conference on Industrial Cyberphysical Systems (ICPS)}, publisher = {IEEE}, address = {New York, NY}, doi = {10.1109/ICPS48405.2020.9274766}, pages = {297 -- 302}, year = {2020}, abstract = {In this paper we present SMART-FACTORY, a setup for a research and teaching facility in industrial robotics that is based on the RoboCup Logistics League. It is driven by the need for developing and applying solutions for digital production. Digitization receives constantly increasing attention in many areas, especially in industry. The common theme is to make things smart by using intelligent computer technology. Especially in the last decade there have been many attempts to improve existing processes in factories, for example, in production logistics, also with deploying cyber-physical systems. An initiative that explores challenges and opportunities for robots in such a setting is the RoboCup Logistics League. Since its foundation in 2012 it is an international effort for research and education in an intra-warehouse logistics scenario. During seven years of competition a lot of knowledge and experience regarding autonomous robots was gained. This knowledge and experience shall provide the basis for further research in challenges of future production. The focus of our SMART-FACTORY is to create a stimulating environment for research on logistics robotics, for teaching activities in computer science and electrical engineering programmes as well as for industrial users to study and explore the feasibility of future technologies. Building on a very successful history in the RoboCup Logistics League we aim to provide stakeholders with a dedicated facility oriented at their individual needs.}, language = {en} } @inproceedings{EllerwegRitz2008, author = {Ellerweg, Roland and Ritz, Thomas}, title = {Tool supported requirements analysis for the user centered development of mobile enterprise software}, series = {Proceeding of Wireless Applications and Computing 2008 and Telecommunications, Networks and Systems 2008 : MCCSIS '08 ; IADIS Multi Conference on Computer Science and Information Systems ; 22 - 24 July 2008, Amsterdam, The Netherlands}, booktitle = {Proceeding of Wireless Applications and Computing 2008 and Telecommunications, Networks and Systems 2008 : MCCSIS '08 ; IADIS Multi Conference on Computer Science and Information Systems ; 22 - 24 July 2008, Amsterdam, The Netherlands}, editor = {Roth, J{\"o}rg}, publisher = {IADIS Press}, address = {[Lisboa]}, isbn = {978-972-8924-62-1}, pages = {160 -- 162}, year = {2008}, abstract = {A user centered development method has proved satisfactory for the development of mobile enterprise software. To make use of this method, detailed information about the user and the place where the user interacts with his mobile device is required. This article describes how both can be modeled by a stereotypical and conceptual extended UML extension. Finally, a software tool is presented that supports the developed UML extension.}, language = {en} } @article{WolfFoltzKillichetal.2001, author = {Wolf, Martin R. and Foltz, Christian and Killich, Stephan and Schmidt, Ludger}, title = {Task and Information Modeling for Cooperative Work / Foltz, Christian ; Killich, Stephan ; Wolf, Martin ; Schmidt, Ludger ; Luczak, Holger}, series = {Systems, social and internationalization design aspects of human-computer interaction / ed. by Michael J. Smith, Gavriel Salvendy Vol. 2}, journal = {Systems, social and internationalization design aspects of human-computer interaction / ed. by Michael J. Smith, Gavriel Salvendy Vol. 2}, publisher = {-}, isbn = {0-8058-3608-X}, pages = {172 -- 176}, year = {2001}, language = {en} } @inproceedings{FerreinPotgieterSteinbauer2009, author = {Ferrein, Alexander and Potgieter, Anet and Steinbauer, Gerald}, title = {Self-aware robots - What do we need from learning, deliberation, and reactive control?}, series = {HYCAS 2009 : International Workshop on Hybrid Control of Autonomous Systems : Integrating Learning, Deliberation and Reactive Control : Pasadena, Calif., 13 July 2009}, booktitle = {HYCAS 2009 : International Workshop on Hybrid Control of Autonomous Systems : Integrating Learning, Deliberation and Reactive Control : Pasadena, Calif., 13 July 2009}, publisher = {AAAI Pr.}, pages = {1 -- 5}, year = {2009}, language = {en} } @inproceedings{SteuerDankert2023, author = {Steuer-Dankert, Linda}, title = {A crazy little thing called sustainability}, series = {51st Annual Conference of the European Society for Engineering Education (SEFI)}, booktitle = {51st Annual Conference of the European Society for Engineering Education (SEFI)}, doi = {10.21427/9CQR-VC94}, pages = {11 Seiten}, year = {2023}, abstract = {Achieving the 17 Sustainable Development Goals (SDGs) set by the United Nations (UN) in 2015 requires global collaboration between different stakeholders. Industry, and in particular engineers who shape industrial developments, have a special role to play as they are confronted with the responsibility to holistically reflect sustainability in industrial processes. This means that, in addition to the technical specifications, engineers must also question the effects of their own actions on an ecological, economic and social level in order to ensure sustainable action and contribute to the achievement of the SDGs. However, this requires competencies that enable engineers to apply all three pillars of sustainability to their own field of activity and to understand the global impact of industrial processes. In this context, it is relevant to understand how industry already reflects sustainability and to identify competences needed for sustainable development.}, language = {en} } @article{HeuermannSadeghfam2004, author = {Heuermann, Holger and Sadeghfam, Arash}, title = {Novel balanced inductor for compact differential systems / Sadeghfam, Arash; Heuermann, Holger}, series = {Conference proceedings : Tuesday 12th, Wednesday 13th and Thursday 14th October, [RAI International Exhibition and Congress Centre, Amsterdam ; part of European Microwave Week 2004] / EuMA, European Microwave Association}, journal = {Conference proceedings : Tuesday 12th, Wednesday 13th and Thursday 14th October, [RAI International Exhibition and Congress Centre, Amsterdam ; part of European Microwave Week 2004] / EuMA, European Microwave Association}, publisher = {Horizon House Publ.}, address = {London}, isbn = {1-580-53992-0}, pages = {709 -- 712}, year = {2004}, language = {en} } @book{FerreinPauliSiebeletal.2009, author = {Ferrein, Alexander and Pauli, J. and Siebel, N. T. and Steinbauer, Gerald}, title = {Hybrid control for autonomous systems : [... 1st Workshop on Hybrid Control of Autonomous Systems - Integrating Learning, Deliberation and Reactive Control with the 21st International Joint Conference on Artificial Intelligence (IJCAI-09), held in Pasadena, CA, in July 2009] / ed. by Alexander Ferrein ...}, pages = {VI, 96 S.}, year = {2009}, language = {en} } @article{HeuermannSchiek1994, author = {Heuermann, Holger and Schiek, Burkhard}, title = {Error Corrected Impedance Measurements with a Network Analyzer}, pages = {125 -- 126}, year = {1994}, language = {en} } @article{NiemuellerFerreinEckeletal.2011, author = {Niem{\"u}ller, Tim and Ferrein, Alexander and Eckel, Gerhard and Pirro, David and Podbregar, Patrick and Kellner, Tobias and Rath, Christoph and Steinbauer, Gerald}, title = {Providing Ground-truth Data for the Nao Robot Platform}, series = {RoboCup 2010: Robot Soccer World Cup XIV}, journal = {RoboCup 2010: Robot Soccer World Cup XIV}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-642-20217-9}, pages = {133 -- 144}, year = {2011}, language = {en} } @incollection{AlhwarinFerreinScholl2014, author = {Alhwarin, Faraj and Ferrein, Alexander and Scholl, Ingrid}, title = {IR stereo kinect: improving depth images by combining structured light with IR stereo}, series = {PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862)}, booktitle = {PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862)}, publisher = {Springer}, address = {M{\"u}nchen}, isbn = {978-3-319-13559-5 (Print) ; 978-3-319-13560-1 (E-Book)}, doi = {10.1007/978-3-319-13560-1_33}, pages = {409 -- 421}, year = {2014}, abstract = {RGB-D sensors such as the Microsoft Kinect or the Asus Xtion are inexpensive 3D sensors. A depth image is computed by calculating the distortion of a known infrared light (IR) pattern which is projected into the scene. While these sensors are great devices they have some limitations. The distance they can measure is limited and they suffer from reflection problems on transparent, shiny, or very matte and absorbing objects. If more than one RGB-D camera is used the IR patterns interfere with each other. This results in a massive loss of depth information. In this paper, we present a simple and powerful method to overcome these problems. We propose a stereo RGB-D camera system which uses the pros of RGB-D cameras and combine them with the pros of stereo camera systems. The idea is to utilize the IR images of each two sensors as a stereo pair to generate a depth map. The IR patterns emitted by IR projectors are exploited here to enhance the dense stereo matching even if the observed objects or surfaces are texture-less or transparent. The resulting disparity map is then fused with the depth map offered by the RGB-D sensor to fill the regions and the holes that appear because of interference, or due to transparent or reflective objects. Our results show that the density of depth information is increased especially for transparent, shiny or matte objects.}, language = {en} } @inproceedings{HeuermannFinger2014, author = {Heuermann, Holger and Finger, Torsten}, title = {2.45 GHz Plasma Powered Spark Plug by Thermal and EM-Optimization}, pages = {30 Folien}, year = {2014}, language = {en} } @article{HeuermannEmmrichBongartz2022, author = {Heuermann, Holger and Emmrich, Thomas and Bongartz, Simon}, title = {Microwave spark plug to support ignitions with high compression ratios}, series = {IEEE Transactions on Plasma Science}, journal = {IEEE Transactions on Plasma Science}, number = {Early Access}, publisher = {IEEE}, issn = {1939-9375}, doi = {10.1109/TPS.2022.3183690}, pages = {1 -- 6}, year = {2022}, abstract = {Upcoming gasoline engines should run with a larger number of fuels beginning from petrol over methanol up to gas by a wide range of compression ratios and a homogeneous charge. In this article, the microwave (MW) spark plug, based on a high-speed frequency hopping system, is introduced as a solution, which can support a nitrogen compression ratio up to 1:39 in a chamber and more. First, an overview of the high-speed frequency hopping MW ignition and operation system as well as the large number of applications are presented. Both gives an understanding of this new base technology for MW plasma generation. Focus of the theoretical part is the explanation of the internal construction of the spark plug, on the achievable of the high voltage generation as well as the high efficiency to hold the plasma. In detail, the development process starting with circuit simulations and ending with the numerical multiphysics field simulations is described. The concept is evaluated with a reference prototype covering the frequency range between 2.40 and 2.48 GHz and working over a large power range from 20 to 200 W. A larger number of different measurements starting by vector hot-S11 measurements and ending by combined working scenarios out of hot temperature, high pressure and charge motion are winding up the article. The limits for the successful pressure tests were given by the pressure chamber. Pressures ranged from 1 to 39 bar and charge motion up to 25 m/s as well as temperatures from 30◦ to 125◦.}, language = {en} } @article{Ritz2000, author = {Ritz, Thomas}, title = {Personalized information services : an electronic information commodity and its production}, series = {International Journal of E-Business Strategy Management}, volume = {2}, journal = {International Journal of E-Business Strategy Management}, number = {2}, issn = {1467-0305}, year = {2000}, language = {en} } @inproceedings{SchoppHeuermannHoltrup2014, author = {Schopp, Christoph and Heuermann, Holger and Holtrup, S.}, title = {Investigation on efficacy optimization of RF-driven automotive D-lamps}, series = {44th European Microwave Conference (EuMC),2014, Rome}, booktitle = {44th European Microwave Conference (EuMC),2014, Rome}, doi = {10.1109/EuMC.2014.6986645}, pages = {1154 -- 1157}, year = {2014}, language = {en} } @article{FerreinJacobsLakemeyer2005, author = {Ferrein, Alexander and Jacobs, Stefan and Lakemeyer, Gerhard}, title = {Unreal Golog Bots / Jacobs, Stefan ; Ferrein, Alexander ; Lakemeyer, Gerhard}, series = {IJCAI-05 Workshop on Reasoning, Representation, and Learning in Computer Games}, journal = {IJCAI-05 Workshop on Reasoning, Representation, and Learning in Computer Games}, pages = {31 -- 36}, year = {2005}, language = {en} } @article{HeuermannSchiek1997, author = {Heuermann, Holger and Schiek, B.}, title = {Results of network analyzer measurements with leakage errors-corrected with direct calibration techniques}, series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5}, journal = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5}, isbn = {0018-9456}, pages = {1120 -- 1127}, year = {1997}, language = {en} } @article{FerreinBoehnstedtLakemeyer2007, author = {Ferrein, Alexander and B{\"o}hnstedt, Lutz and Lakemeyer, Gerhard}, title = {Options in readylog reloaded -- generating decision-theoretic plan libraries in golog / B{\"o}hnstedt, Lutz ; Ferrein, Alexander ; Lakemeyer, Gerhard}, series = {KI 2007: advances in artificial intelligence : 30th Annual German Conference on AI, KI 2007, Osnabr{\"u}ck, Germany, September 10 - 13, 2007 ; proceedings}, journal = {KI 2007: advances in artificial intelligence : 30th Annual German Conference on AI, KI 2007, Osnabr{\"u}ck, Germany, September 10 - 13, 2007 ; proceedings}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-540-74564-8}, pages = {352 -- 366}, year = {2007}, language = {en} } @inproceedings{NeumannFerreinKallweitetal.2014, author = {Neumann, Tobias and Ferrein, Alexander and Kallweit, Stephan and Scholl, Ingrid}, title = {Towards a mobile mapping robot for underground mines}, series = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town}, booktitle = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town}, organization = {Conference of Robotics and Mechatronics <7, 2014, Cape Town, South Africa>}, pages = {1 -- 6}, year = {2014}, language = {en} } @article{Heuermann1995, author = {Heuermann, Holger}, title = {LZY: A Self-Calibration Approach in Competition to the LRM Method for On-Wafer Measurements}, pages = {129 -- 136}, year = {1995}, language = {en} } @article{WolfFoltzSchlicketal.2002, author = {Wolf, Martin R. and Foltz, Christian and Schlick, Christopher and Luczak, Holger}, title = {Development and evaluation of a groupware system to support chemical design processes / Wolf, Martin ; Foltz, Christian ; Schlick, Christopher ; Luczak, Holger}, series = {International Journal of Human-Computer Interaction . 14 (2002), H. 2}, journal = {International Journal of Human-Computer Interaction . 14 (2002), H. 2}, publisher = {-}, isbn = {1044-7318}, pages = {181 -- 198}, year = {2002}, language = {en} } @article{HeuermannSchiek1993, author = {Heuermann, Holger and Schiek, Burkhard}, title = {LNN( Line-Network-Network): The In-Fixture Calibration Procedure}, pages = {149 -- 149}, year = {1993}, language = {en} } @article{HeuermannSchiek1992, author = {Heuermann, Holger and Schiek, Burkhard}, title = {A Generalization of the Txx Network Analyzer Self-Calibration Procedure}, series = {Conference proceedings : monday 24th to thursday 27th august 1992, Helsinki University of Technology, Espoo, Finland ; [the international conference and exhibition designed for the Microwave Community]. Vol. 2}, journal = {Conference proceedings : monday 24th to thursday 27th august 1992, Helsinki University of Technology, Espoo, Finland ; [the international conference and exhibition designed for the Microwave Community]. Vol. 2}, publisher = {Microwave Exhibitions and Publishers}, address = {Tunbridge Wells}, isbn = {0-946821-77-1}, pages = {907 -- 912}, year = {1992}, language = {en} } @article{HeuermannSchiek1997, author = {Heuermann, Holger and Schiek, B.}, title = {15-term self-calibration methods for the error-correction of on-wafer measurements}, series = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5}, journal = {IEEE transactions on instrumentation and measurement : IM / Institute of Electrical and Electronics Engineers, Instrumentation and Measurement Group. 46 (1997), H. 5}, isbn = {0018-9456}, pages = {1105 -- 1110}, year = {1997}, language = {en} } @article{WolfLuczakSpringeretal.1997, author = {Wolf, Martin R. and Luczak, Holger and Springer, J. and Simon, S.}, title = {The role of metaphors in computer supported cooperative work}, series = {Proceedings of WWDU '97 Tokyo, Fifth International Scientific Conference on Work with Display Units : November 3 - 5, 1997, Tokyo /}, journal = {Proceedings of WWDU '97 Tokyo, Fifth International Scientific Conference on Work with Display Units : November 3 - 5, 1997, Tokyo /}, editor = {Miyamoto, Hiroyuki}, publisher = {-}, address = {Tokyo}, pages = {191 -- 192}, year = {1997}, language = {en} } @incollection{HeuermannFinger2014, author = {Heuermann, Holger and Finger, Torsten}, title = {Microwave Spark Plug for Very High-Pressure Conditions}, series = {Ignition systems for gasoline engines}, booktitle = {Ignition systems for gasoline engines}, editor = {G{\"u}nther, Michael}, publisher = {DCM Druck}, address = {Meckenheim}, pages = {269 -- 282}, year = {2014}, language = {en} } @article{FerreinMeyer2012, author = {Ferrein, Alexander and Meyer, Thomas}, title = {A Brief Overview of Artificial Intelligence in South Africa}, series = {AI Magazine}, volume = {33}, journal = {AI Magazine}, number = {1}, publisher = {AAAI}, address = {Menlo Park}, issn = {0738-4602}, doi = {10.1609/aimag.v33i1.2357}, pages = {99 -- 101}, year = {2012}, abstract = {South Africa in recent years is the establishment of a number of research hubs involved in AI activities ranging from mobile robotics and computational intelligence, to knowledge representation and reasoning, and human language technologies. In this survey we take the reader through a quick tour of the research being conducted at these hubs, and touch on an initiative to maintain and extend the current level of interest in AI research in the country.}, language = {en} } @inproceedings{DammRitzStrauch2011, author = {Damm, Sebastian and Ritz, Thomas and Strauch, Jakob}, title = {Adaption of archetype patterns for mobile cloud-based business apps}, series = {2011 IEEE International Conference on Pervasive Computing and Communications workshops (PerCom workshops 2011) : Seattle, Washington, USA, 21 - 25 March 2011}, booktitle = {2011 IEEE International Conference on Pervasive Computing and Communications workshops (PerCom workshops 2011) : Seattle, Washington, USA, 21 - 25 March 2011}, publisher = {IEEE Service Center}, address = {Piscataway, NJ}, isbn = {978-1-61284-938-6 (Print)}, doi = {10.1109/PERCOMW.2011.5766849}, pages = {100 -- 105}, year = {2011}, language = {en} } @article{SteinbauerFerrein2016, author = {Steinbauer, Gerald and Ferrein, Alexander}, title = {20 Years of RoboCup}, series = {KI - K{\"u}nstliche Intelligenz}, volume = {30}, journal = {KI - K{\"u}nstliche Intelligenz}, number = {3-4}, publisher = {Springer}, address = {Berlin}, issn = {1610-1987}, doi = {10.1007/s13218-016-0442-z}, pages = {221 -- 224}, year = {2016}, language = {en} } @article{FerreinFritzLakemeyer2003, author = {Ferrein, Alexander and Fritz, Christian and Lakemeyer, Gerhard}, title = {Extending DTGOLOG with Options / Ferrein, Alexander ; Fritz, Christian ; Lakemeyer, Gerhard}, series = {IJCAI-03, Proceedings of the Eighteenth International Joint Conference on Artificial Intelligence, Acapulco, Mexico, August 9-15, 2003}, journal = {IJCAI-03, Proceedings of the Eighteenth International Joint Conference on Artificial Intelligence, Acapulco, Mexico, August 9-15, 2003}, pages = {1391 -- 1393}, year = {2003}, language = {en} }