@inproceedings{MarinkovićButenweg2019, author = {Marinković, Marko and Butenweg, Christoph}, title = {Experimental and numerical analysis of RC frames with decoupled masonry infills}, series = {7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering}, booktitle = {7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering}, editor = {Papadrakakis, Manolis and Fragiadakis, Michalis}, publisher = {National Technical University of Athens}, address = {Athen}, isbn = {978-618-82844-5-6}, issn = {2623-3347}, doi = {10.7712/120119.7088.18845}, pages = {2464 -- 2479}, year = {2019}, abstract = {Masonry infill walls are commonly used in reinforced concrete (RC) frame structures, also in seismically active areas, although they often experience serious damage during earthquakes. One of the main reasons for their poor behaviour is the connection to the frame, which is usually constructed using mortar. This paper describes the novel solution for infill/frame connection based on application of elastomeric material between them. The system called INODIS (Innovative Decoupled Infill System) has the aim to postpone the activation of infill in in-plane direction and at the same time to provide sufficient out-of-plane support. First, experimental tests on infilled frame specimens are presented and the comparison of the results between traditionally infilled frames and infilled frames with the INODIS system are given. The results are then used for calibration and validation of numerical model, which can be further employed for investigating the influence of some material parameters on the behaviour of infilled frames with the INODIS system.}, language = {en} } @inproceedings{MarinkovićButenweg2020, author = {Marinković, Marko and Butenweg, Christoph}, title = {Out-of-plane behavior of decoupled masonry infills under seismic loading}, series = {17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.}, booktitle = {17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.}, pages = {13 Seiten}, year = {2020}, abstract = {Masonry is used in many buildings not only for load-bearing walls, but also for non-load-bearing enclosure elements in the form of infill walls. Many studies confirmed that infill walls interact with the surrounding reinforced concrete frame, thus changing dynamic characteristics of the structure. Consequently, masonry infills cannot be neglected in the design process. However, although the relevant standards contain requirements for infill walls, they do not describe how these requirements are to be met concretely. This leads in practice to the fact that the infill walls are neither dimensioned nor constructed correctly. The evidence of this fact is confirmed by the recent earthquakes, which have led to enormous damages, sometimes followed by the total collapse of buildings and loss of human lives. Recently, the increasing effort has been dedicated to the approach of decoupling of masonry infills from the frame elements by introducing the gap in between. This helps in removing the interaction between infills and frame, but raises the question of out-of-plane stability of the panel. This paper presents the results of the experimental campaign showing the out-of-plane behavior of masonry infills decoupled with the system called INODIS (Innovative decoupled infill system), developed within the European project INSYSME (Innovative Systems for Earthquake Resistant Masonry Enclosures in Reinforced Concrete Buildings). Full scale specimens were subjected to the different loading conditions and combinations of in-plane and out-of-plane loading. Out-of-plane capacity of the masonry infills with the INODIS system is compared with traditionally constructed infills, showing that INODIS system provides reliable out-of-plane connection under various loading conditions. In contrast, traditional infills performed very poor in the case of combined and simultaneously applied in-plane and out-of-plane loading, experiencing brittle behavior under small in-plane drifts followed by high out-of-plane displacements. Decoupled infills with the INODIS system have remained stable under out-of-plane loads, even after reaching high in-plane drifts and being damaged.}, language = {en} } @article{MarinkovicButenweg2020, author = {Marinkovic, Marko and Butenweg, Christoph}, title = {Ausfachungen aus Ziegelmauerwerk in Stahlbetonrahmentragwerken unter Erdbebenbeanspruchung}, series = {Mauerwerk}, volume = {24}, journal = {Mauerwerk}, number = {4}, publisher = {Wiley}, address = {Weinheim}, issn = {1437-1022}, doi = {10.1002/dama.202000011}, pages = {194 -- 205}, year = {2020}, abstract = {Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk weisen nach Erdbeben h{\"a}ufig schwere Sch{\"a}den auf. Gr{\"u}nde hierf{\"u}r sind die Beanspruchungen der Ausfachungsw{\"a}nde durch die aufgezwungenen Rahmenverformungen in Wandebene und die gleichzeitig auftretenden Tr{\"a}gheitskr{\"a}fte senkrecht zur Wandebene in Kombination mit der konstruktiven Ausf{\"u}hrung des Ausfachungsmauerwerks. Die Ausfachung wird in der Regel knirsch gegen die Rahmenst{\"u}tzen gemauert, wobei der Verschluss der oberen Fuge mit M{\"o}rtel oder Montageschaum erfolgt. Dadurch kommt es im Erdbebenfall zu lokalen Interaktionen zwischen Ausfachung und Rahmen, die in der Folge zu einem Versagen einzelner Ausfachungsw{\"a}nde oder zu einem sukzessiven Versagen des Gesamtgeb{\"a}udes f{\"u}hren k{\"o}nnen. Die beobachteten Sch{\"a}den waren die Motivation daf{\"u}r, in dem europ{\"a}ischen Forschungsprojekt INSYSME f{\"u}r Stahlbetonrahmentragwerke mit Ausfachungen aus hochw{\"a}rmed{\"a}mmenden Ziegelmauerwerk innovative L{\"o}sungen zur Verbesserung des seismischen Verhaltens zu entwickeln. Der vorliegende Beitrag stellt die im Rahmen des Projekts von den deutschen Projektpartnern (Universit{\"a}t Kassel, SDA-engineering GmbH) entwickelten L{\"o}sungen vor und vergleicht deren seismisches Verhalten mit der traditionellen Ausf{\"u}hrung der Ausfachungsw{\"a}nde. Grundlage f{\"u}r den Vergleich sind statisch-zyklische Wandversuche und Simulationen auf Wandebene. Aus den Ergebnissen werden Empfehlungen f{\"u}r die erdbebensichere Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk abgeleitet.}, language = {de} } @article{MarinkovicButenweg2020, author = {Marinkovic, Marko and Butenweg, Christoph}, title = {Earthquake-proof system for masonry infills in RC frame structures}, series = {International Journal of Masonry Research and Innovation}, volume = {5}, journal = {International Journal of Masonry Research and Innovation}, number = {2}, publisher = {Inderscience Enterprises}, address = {Olney, Bucks}, issn = {2056-9467}, doi = {10.1504/IJMRI.2020.106328}, pages = {185 -- 208}, year = {2020}, language = {de} } @article{MarinkovicButenweg2019, author = {Marinkovic, Marko and Butenweg, Christoph}, title = {Innovative decoupling system for the seismic protection of masonry infill walls in reinforced concrete frames}, series = {Engineering Structures}, volume = {197}, journal = {Engineering Structures}, number = {Article 109435}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0141-0296}, doi = {10.1016/j.engstruct.2019.109435}, year = {2019}, language = {en} } @inproceedings{MarinkovicButenweg2018, author = {Marinkovic, Marko and Butenweg, Christoph}, title = {Innovative System for Earthquake Resistant Masonry Infill Walls}, series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018}, booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018}, pages = {1 -- 12}, year = {2018}, language = {en} } @inproceedings{MarinkovicButenweg2020, author = {Marinkovic, Marko and Butenweg, Christoph}, title = {Seismic behaviour of RC frames with uncoupled masonry infills having two storeys or two bays}, series = {17th International Conference -From historical to sustainable masonry, Krakow, Poland, July 5-8, 2020}, booktitle = {17th International Conference -From historical to sustainable masonry, Krakow, Poland, July 5-8, 2020}, doi = {10.1201/9781003098508-72}, pages = {1 -- 7}, year = {2020}, language = {en} } @article{MarinkovicButenweg2022, author = {Marinkovic, Marko and Butenweg, Christoph}, title = {Numerical analysis of the in-plane behaviour of decoupled masonry infilled RC frames}, series = {Engineering Structures}, volume = {272}, journal = {Engineering Structures}, number = {1}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0141-0296}, doi = {10.1016/j.engstruct.2022.114959}, pages = {18 Seiten}, year = {2022}, abstract = {Damage of reinforced concrete (RC) frames with masonry infill walls has been observed after many earthquakes. Brittle behaviour of the masonry infills in combination with the ductile behaviour of the RC frames makes infill walls prone to damage during earthquakes. Interstory deformations lead to an interaction between the infill and the RC frame, which affects the structural response. The result of this interaction is significant damage to the infill wall and sometimes to the surrounding structural system too. In most design codes, infill walls are considered as non-structural elements and neglected in the design process, because taking into account the infills and considering the interaction between frame and infill in software packages can be complicated and impractical. A good way to avoid negative aspects arising from this behavior is to ensure no or low-interaction of the frame and infill wall, for instance by decoupling the infill from the frame. This paper presents the numerical study performed to investigate new connection system called INODIS (Innovative Decoupled Infill System) for decoupling infill walls from surrounding frame with the aim to postpone infill activation to high interstory drifts thus reducing infill/frame interaction and minimizing damage to both infills and frames. The experimental results are first used for calibration and validation of the numerical model, which is then employed for investigating the influence of the material parameters as well as infill's and frame's geometry on the in-plane behaviour of the infilled frames with the INODIS system. For all the investigated situations, simulation results show significant improvements in behaviour for decoupled infilled RC frames in comparison to the traditionally infilled frames.}, language = {en} } @inproceedings{LuBeyerBosiljkovetal.2016, author = {Lu, S. and Beyer, K. and Bosiljkov, V. and Butenweg, Christoph and D'Ayala, D. and Degee, H. and Gams, M. and Klouda, J. and Lagomarsino, S. and Penna, A. and Mojsilovic, N. and da Porto, F. and Sorrentino, L. and Vintzileou, E.}, title = {Next generation of Eurocode 8, masonry chapter}, series = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016}, booktitle = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016}, editor = {Modena, Claudio and da Porto, F. and Valluzzi, M.R.}, publisher = {Taylor \& Francis}, address = {London}, isbn = {978-1-138-02999-6 (Print)}, pages = {695 -- 700}, year = {2016}, abstract = {This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date.}, language = {en} } @inproceedings{LoschButenweg1999, author = {Losch, S. and Butenweg, Christoph}, title = {Qualit{\"a}tsgesteuerte Bemessung von Stahlbetontragwerken mit der FE-Methode}, series = {11. Forum Bauinformatik Darmstadt '99 : [Beitr{\"a}ge der Forumsteilnehmer, die im Rahmen des 11. Forums Bauinformatik vom 22. bis 24. September 1999 in Darmstadt ihre Forschung pr{\"a}sentiert ...] / Tobias Kuhn ... (Hrsg.) (Fortschritt-Berichte VDI : Reihe 4 Bauingenieurwesen ; Nr. 156)}, booktitle = {11. Forum Bauinformatik Darmstadt '99 : [Beitr{\"a}ge der Forumsteilnehmer, die im Rahmen des 11. Forums Bauinformatik vom 22. bis 24. September 1999 in Darmstadt ihre Forschung pr{\"a}sentiert ...] / Tobias Kuhn ... (Hrsg.) (Fortschritt-Berichte VDI : Reihe 4 Bauingenieurwesen ; Nr. 156)}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, organization = {Forum Bauinformatik <11, 1999, Darmstadt>}, isbn = {3-18-315604-0}, pages = {208 -- 215}, year = {1999}, language = {de} } @incollection{KuhlmannButenwegMeskourisetal.2012, author = {Kuhlmann, Wolfram and Butenweg, Christoph and Meskouris, Konstantin and Kempen, Thomas}, title = {Simulation des Tragverhaltens des Aachener Doms im Erdbebenfall}, series = {Die karolingische Pfalzkapelle in Aachen : Material, Bautechnik, Restaurierung. (Arbeitshefte der rheinischen Denkmalpflege ; 78)}, booktitle = {Die karolingische Pfalzkapelle in Aachen : Material, Bautechnik, Restaurierung. (Arbeitshefte der rheinischen Denkmalpflege ; 78)}, publisher = {Wernersche Verlags-Gesellschaft}, address = {Worms}, isbn = {978-3-88462-325-1}, pages = {237 -- 248}, year = {2012}, language = {de} } @article{KuhlmannButenwegMeskouris2003, author = {Kuhlmann, Wolfram and Butenweg, Christoph and Meskouris, Konstantin}, title = {Baudynamische Untersuchung des Aachener Doms unter Erdbebenbelastung}, series = {Bautechnik : Zeitschrift f{\"u}r den gesamten Ingenieurbau}, volume = {Vol. 80}, journal = {Bautechnik : Zeitschrift f{\"u}r den gesamten Ingenieurbau}, number = {Iss. 10}, issn = {1437-0999 (E-Journal); 0005-6820 (Print); 0932-8351 (Print)}, doi = {10.1002/bate.200305080}, pages = {675 -- 684}, year = {2003}, language = {de} } @inproceedings{KuhlmannButenwegLopezetal.2004, author = {Kuhlmann, Wolfram and Butenweg, Christoph and Lopez, Marijen and Fernandez, Sebastian}, title = {Seismic vulnerability assessment of the historic Aachen Cathedral}, series = {Conference proceedings / 13th World Conference on Earthquake Engineering [Vancouver, British Columbia, Canada, August 1 - 6, 2004] / [hosted by CAEE/ACGP, Canadian Association for Earthquake Engineering]}, booktitle = {Conference proceedings / 13th World Conference on Earthquake Engineering [Vancouver, British Columbia, Canada, August 1 - 6, 2004] / [hosted by CAEE/ACGP, Canadian Association for Earthquake Engineering]}, publisher = {CAEE}, address = {Vancouver}, organization = {World Conference on Earthquake Engineering <13, 2004, Vancouver>}, pages = {1 -- 14}, year = {2004}, language = {en} } @inproceedings{KuhlmannButenwegBettziecheetal.2004, author = {Kuhlmann, Wolfram and Butenweg, Christoph and Bettzieche, Volker and Meskouris, Konstantin}, title = {Experimentelle und numerische Untersuchungen zur baudynamischen Beurteilung von Talsperren des Ruhrverbandes}, series = {13. Deutsches Talsperrensymposium in Weimar}, booktitle = {13. Deutsches Talsperrensymposium in Weimar}, organization = {Deutsches Talsperrensymposium <13, 2004, Weimar>}, pages = {1 -- 26}, year = {2004}, language = {de} } @article{KuhlmannButenwegBettzieche2006, author = {Kuhlmann, Wolfram and Butenweg, Christoph and Bettzieche, Volker}, title = {Experimentelle und numerische Untersuchungen zur baudynamischen Beurteilung von Talsperren}, series = {Wasserwirtschaft : Hydrologie, Wasserbau, Hydromechanik, Gew{\"a}sser, {\"O}kologie, Boden}, volume = {Band 96}, journal = {Wasserwirtschaft : Hydrologie, Wasserbau, Hydromechanik, Gew{\"a}sser, {\"O}kologie, Boden}, number = {Heft 5}, issn = {0043-0978 (E-Journal); 0043-0978 (Print)}, pages = {10 -- 16}, year = {2006}, language = {de} } @incollection{KuhlmannBettziecheRoesleretal.2005, author = {Kuhlmann, W. and Bettzieche, V. and Roesler, F. and Butenweg, Christoph and K{\"o}nke, C. and Meskouris, Konstantin}, title = {Baudynamische Untersuchung von Talsperren des Ruhrverbandes}, series = {Neubewertung der Erdbebensicherheit von Talsperren in Deutschland : DGEB-Workshop, 28. November 2003 in Potsdam = Assessment of the seismic safety of dams in Germany / organisiert von der Deutschen Gesellschaft f{\"u}r Erdbebeningenieurwesen und Baudynamik. K. Meskouris ... (Hrsg.) (DGEB-Publikation ; Nr. 12)}, booktitle = {Neubewertung der Erdbebensicherheit von Talsperren in Deutschland : DGEB-Workshop, 28. November 2003 in Potsdam = Assessment of the seismic safety of dams in Germany / organisiert von der Deutschen Gesellschaft f{\"u}r Erdbebeningenieurwesen und Baudynamik. K. Meskouris ... (Hrsg.) (DGEB-Publikation ; Nr. 12)}, publisher = {DGEB}, address = {Aachen}, isbn = {3-930108-08-9}, pages = {37 -- 48}, year = {2005}, language = {de} } @article{KubalskiButenwegElDeib2022, author = {Kubalski, Thomas and Butenweg, Christoph and El-Deib, Khaled}, title = {Vereinfachte Ber{\"u}cksichtigung der Rahmentragwirkung in Mauerwerksgeb{\"a}uden}, series = {Bautechnik}, volume = {99}, journal = {Bautechnik}, number = {12}, editor = {Jesse, Dirk}, publisher = {Ernst \& Sohn}, address = {Berlin}, issn = {0932-8351}, doi = {10.1002/bate.202200081}, pages = {865 -- 928}, year = {2022}, abstract = {Aufgrund der gestiegenen Anforderungen durch h{\"o}here Ein-wirkungen aus Wind und Erdbeben ist eine Verbesserung und Optimierung der Berechnungs- und Bemessungsans{\"a}tze f{\"u}r Mauerwerksbauten erforderlich. Eine bessere Ausnutzung der Tragwerksreserven ist durch die Ber{\"u}cksichtigung der Rah-mentragwirkung mit einer Aktivierung der Deckenscheiben in den Rechenmodellen m{\"o}glich, die in der Praxis aufgrund der Komplexit{\"a}t der Wand-Decken-Interaktion bislang nicht aus-genutzt wird. Im vorliegenden Aufsatz wird ein vereinfachter Ansatz auf Grundlage der mitwirkenden Plattenbreite von Schubw{\"a}nden aus Mauerwerk vorgestellt, der die wesentli-chen Einfl ussfaktoren in parametrisierten Tabellen erfasst. Damit steht den Tragwerksplanern ein einfach anwendbares Werkzeug zur Verf{\"u}gung, um die Rahmentragwirkung in der Mauerwerksbemessung anzusetzen.}, language = {de} } @article{KubalskiButenweg2015, author = {Kubalski, Thomas and Butenweg, Christoph}, title = {Modelling strategies for horizontally loaded infill masonry}, series = {Mauerwerk : European journal of masonry}, volume = {Volume 19}, journal = {Mauerwerk : European journal of masonry}, number = {Issue 5}, publisher = {Wiley}, address = {Weinheim}, doi = {10.1002/dama.201500675}, pages = {363 -- 369}, year = {2015}, language = {de} } @inproceedings{KubalskiMarinkovićButenweg2016, author = {Kubalski, T. and Marinković, Marko and Butenweg, Christoph}, title = {Numerical investigation of masonry infilled R.C. frames}, series = {Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016}, booktitle = {Brick and Block Masonry. Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016}, editor = {Modena, Claudio}, publisher = {CRC Press}, address = {Leiden}, isbn = {9781315374963}, pages = {1219 -- 1226}, year = {2016}, language = {en} } @inproceedings{KubalskiButenwegMarinkovićetal.2017, author = {Kubalski, T. and Butenweg, Christoph and Marinković, Marko and Klinkel, S.}, title = {Investigation Of The Seismic Behaviour Of Infill Masonry Using Numerical Modelling Approaches}, series = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017}, booktitle = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017}, publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)}, pages = {1 -- 11}, year = {2017}, abstract = {Masonry is a widely spread construction type which is used all over the world for different types of structures. Due to its simple and cheap construction, it is used as non-structural as well as structural element. In frame structures, such as reinforced concrete frames, masonry may be used as infill. While the bare frame itself is able to carry the loads when it comes to seismic events, the infilled frame is not able to warp freely due to the constrained movement. This restraint results in a complex interaction between the infill and the surrounding frame, which may lead to severe damage to the infill as well as the surrounding frame. The interaction is studied in different projects and effective approaches for the description of the behavior are still lacking. Experimental programs are usually quite expensive, while numerical models, once validated, do offer an efficient approach for the investigation of the interaction when horizontally loaded. In order to study the numerous parameters influencing the seismic load bearing behavior, numerical models may be used. Therefore, this contribution presents a numerical approach for the simulation of infill masonry in reinforced concrete frames. Both parts, the surrounding frame as well as the infill are represented by micro modelling approaches to correctly take into account the different types of failure. The adopted numerical model describes the inelastic behavior of the system, as indicated by the obtained results of the overall structural response as well as the formation of damage in the infilled wall. Comparison of the numerical and experimental results highlights the valuable contribution of numerical simulations in the study and design of infilled frames. As damage of the infill masonry may occur in-plane due to the interaction as well as out-of-plane due to the low vertical load, both directions of loading are investigated.}, language = {en} } @inproceedings{KubalskiButenweg2015, author = {Kubalski, T. and Butenweg, Christoph}, title = {Ausfachungsmauerwerk unter kombinierter seismischer Beanspruchung}, series = {Erdbeben und bestehende Bauten : 14. D-A-C-H Tagung 20.08. - 21.08.2015, ETH Z{\"u}rich. (Dokumentation / SIA ; D 0255)}, booktitle = {Erdbeben und bestehende Bauten : 14. D-A-C-H Tagung 20.08. - 21.08.2015, ETH Z{\"u}rich. (Dokumentation / SIA ; D 0255)}, publisher = {SGEB}, address = {Z{\"u}rich}, organization = {D-A-C-H Tagung <14, 2015, Z{\"u}rich>}, isbn = {978-3-03732-060-0}, pages = {117 -- 122}, year = {2015}, language = {de} } @inproceedings{KonradChudobaButenwegetal.2003, author = {Konrad, M. and Chudoba, Rostislav and Butenweg, Christoph and Bruckermann, O.}, title = {Textile reinforced concrete. Part II: Multi-level modeling concept}, series = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke}, booktitle = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke}, publisher = {IKM}, address = {Weimar}, organization = {Internationales Kolloquium {\"u}ber Anwendungen der Informatik und Mathematik in Architektur und Bauwesen <16, 2003, Weimar>}, pages = {1 -- 11}, year = {2003}, language = {en} } @inproceedings{KobGoemmelButenwegetal.2006, author = {Kob, Malte and G{\"o}mmel, Andreas and Butenweg, Christoph and Niendorf, Thoralf}, title = {Training of a combined model of larynx and vocal folds with data from MRI measurements}, series = {The 5th International Conference on Voice Physiology and Biomechanics: Variations across Cultures and Species, July 12-14, 2006, Tokyo, Japan. Proceedings}, booktitle = {The 5th International Conference on Voice Physiology and Biomechanics: Variations across Cultures and Species, July 12-14, 2006, Tokyo, Japan. Proceedings}, organization = {International Conference on Voice Physiology and Biomechanics <5, 2006, Tokyo>}, pages = {45 -- 46}, year = {2006}, language = {en} } @inproceedings{KobButenweg2004, author = {Kob, Malte and Butenweg, Christoph}, title = {A finite element model of the interaction between intra-and extralaryngeal muscles}, series = {International Conference on Voice Physiology and Biomechanics, August 18-20, 2004, Marseille, France}, booktitle = {International Conference on Voice Physiology and Biomechanics, August 18-20, 2004, Marseille, France}, organization = {International Conference on Voice Physiology and Biomechanics <2004, Marseille>}, pages = {1 -- 2}, year = {2004}, language = {en} } @book{KlinkelButenwegLinetal.2014, author = {Klinkel, Sven and Butenweg, Christoph and Lin, Gao and Holtschoppen, Britta}, title = {Seismic design of industrial facilities : Proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF) / Sven Klinkel, Christoph Butenweg, Gao Lin, Britta Holtschoppen Editors}, publisher = {Springer Vieweg}, address = {Wiesbaden}, organization = {International Conference on Seismic Design of Industrial Facilities }, isbn = {978-3-658-02809-1 (Print) ; 978-365-80281-0-7 (E-Book)}, doi = {10.1007/978-3-658-02810-7}, pages = {XIII, 450 S.}, year = {2014}, language = {en} } @article{KleinButenwegKlinkel2017, author = {Klein, Michel and Butenweg, Christoph and Klinkel, Sven}, title = {The Influence of Soil-Structure-Interaction on the Fatigue Analysis in the Foundation Design of Onshore Wind Turbines}, series = {Procedia Engineering}, volume = {199}, journal = {Procedia Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1877-7058}, doi = {10.1016/j.proeng.2017.09.325}, pages = {3218 -- 3223}, year = {2017}, language = {en} } @inproceedings{KarvanekButenwegEbenau2002, author = {Karvanek, Eva and Butenweg, Christoph and Ebenau, Carsten}, title = {Bautechnische Pr{\"u}fung und Bau{\"u}berwachung der Arena „Auf Schalke"}, series = {Berichte der Fachtagung Baustatik - Baupraxis 8 am 21. und 22. M{\"a}rz 2002 in Braunschweig / Hrsg. Dieter Dinkler}, booktitle = {Berichte der Fachtagung Baustatik - Baupraxis 8 am 21. und 22. M{\"a}rz 2002 in Braunschweig / Hrsg. Dieter Dinkler}, publisher = {TU Braunschweig, Institut f{\"u}r Statik}, address = {Braunschweig}, organization = {Fachtagung Baustatik - Baupraxis <8, 2002, Braunschweig>}, isbn = {3-926031-95-6}, pages = {237 -- 245}, year = {2002}, language = {de} } @inproceedings{KarimiButenwegToll2005, author = {Karimi, Iman and Butenweg, Christoph and Toll, Britta}, title = {Vulnerability assessment of industrial facilities}, series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping}, booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping}, publisher = {Civil-Comp Press}, address = {Stirling}, organization = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>}, isbn = {1-905088-00-0}, doi = {10.4203/ccp.81.34}, pages = {34, 73 -- 75}, year = {2005}, language = {en} } @inproceedings{KalkerTollHolleretal.2004, author = {Kalker, Ines and Toll, B. and Holler, Stefan and Butenweg, Christoph and Topping, B. H. V. and Mota Soares, C. A.}, title = {Capacity analysis of textile retrofitted unreinforced masonry}, series = {Proceedings of the Seventh International Conference on Computational Structures Technology : [Lisbon, Portugal, 7 - 9 September 2004] / ed. by B. H. V. Topping ...}, booktitle = {Proceedings of the Seventh International Conference on Computational Structures Technology : [Lisbon, Portugal, 7 - 9 September 2004] / ed. by B. H. V. Topping ...}, publisher = {Civil-Comp Press}, address = {Stirling}, organization = {International Conference on Computational Structures Technology <7, 2004, Lissabon>}, isbn = {0-948749-95-4}, doi = {10.4203/ccp.79.194}, pages = {431 -- 432}, year = {2004}, language = {en} } @inproceedings{KalkerNeumannButenwegetal.2005, author = {Kalker, Ines and Neumann, M. and Butenweg, Christoph and Holler, Stefan}, title = {Modelling of textile strengthened masonry}, series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping}, booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping}, publisher = {Civil-Comp Press}, address = {Stirling}, organization = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>}, isbn = {1-905088-00-0}, doi = {10.4203/ccp.81.184}, pages = {447 -- 448}, year = {2005}, language = {en} } @inproceedings{HoltschoppenCornelissenButenwegetal.2011, author = {Holtschoppen, Britta and Cornelissen, Philipp and Butenweg, Christoph and Meskouris, Konstantin}, title = {Vereinfachtes Berechnungsverfahren zur Ber{\"u}cksichtigung der Interaktionsschwingung bei fl{\"u}ssigkeitsgef{\"u}llten Tankbauwerken unter seismischer Belastung}, series = {Berichte der Fachtagung Baustatik-Baupraxis 11 : am 21. und 22. Februar 2011 an der Universit{\"a}t Innsbruck / Hrsg. Gernot Beer ...}, booktitle = {Berichte der Fachtagung Baustatik-Baupraxis 11 : am 21. und 22. Februar 2011 an der Universit{\"a}t Innsbruck / Hrsg. Gernot Beer ...}, publisher = {Inst. f{\"u}r Baustatik, Techn. Univ. Graz}, address = {Graz}, organization = {Fachtagung Baustatik, Baupraxis <11, 2011, Innsbruck>}, isbn = {978-3-85125-115-9}, pages = {155 -- 162}, year = {2011}, language = {de} } @article{HoltschoppenButenwegMeskouris2009, author = {Holtschoppen, Britta and Butenweg, Christoph and Meskouris, Konstantin}, title = {Seismic design of non-structural components in industrial facilities}, series = {International journal of engineering under uncertainty}, volume = {Volume 1}, journal = {International journal of engineering under uncertainty}, issn = {0975-4806}, pages = {1 -- 13}, year = {2009}, language = {en} } @article{HoltschoppenButenwegMeskouris2009, author = {Holtschoppen, B. and Butenweg, Christoph and Meskouris, Konstantin}, title = {Erdbebensichere Auslegung von Industrieanlagen}, series = {Der Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik}, journal = {Der Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik}, number = {M{\"a}rz}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {S9 -- S14}, year = {2009}, language = {de} } @article{HollerButenwegNohetal.2004, author = {Holler, S. and Butenweg, Christoph and Noh, S.-Y. and Meskouris, Konstantin}, title = {Computational model of textile-reinforced concrete structures}, series = {Computers \& structures : an international journal}, volume = {Volume 82}, journal = {Computers \& structures : an international journal}, number = {Issues 23-26}, issn = {1879-2243 (E-Journal); 0045-7949 (Print)}, doi = {10.1016/j.compstruc.2004.03.076}, pages = {1971 -- 1979}, year = {2004}, language = {en} } @inproceedings{HollerButenwegNohetal.2002, author = {Holler, S. and Butenweg, Christoph and Noh, S.-Y. and Meskouris, Konstantin}, title = {Numerical simulation of textile-reinforced concrete structures}, series = {Proceedings of the Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002] / ed. by B. H. V. Topping and Z. Bittnar. (Civil-Comp Press books on computational engineering)}, booktitle = {Proceedings of the Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002] / ed. by B. H. V. Topping and Z. Bittnar. (Civil-Comp Press books on computational engineering)}, publisher = {Civil-Comp Press}, address = {Stirling}, organization = {International Conference on Computational Structures Technology <6, 2002, Prag>}, isbn = {0-948749-83-0}, pages = {287 -- 288}, year = {2002}, language = {en} } @inproceedings{GoemmelNiendorfFrauenrathetal.2010, author = {G{\"o}mmel, Andreas and Niendorf, Thoralf and Frauenrath, Tobias and Otten, Mario and Butenweg, Christoph and Kob, Malte}, title = {3D vocal fold geometry mapping using Magnetic Resonance Imaging}, series = {Fortschritte der Akustik : 36. Deutsche Jahrestagung f{\"u}r Akustik ; 15.-18. M{\"a}rz 2010, [Berlin ; DAGA 2010] / DEGA ... Wiss. Ed. Michael M{\"o}ser ... Band 1}, booktitle = {Fortschritte der Akustik : 36. Deutsche Jahrestagung f{\"u}r Akustik ; 15.-18. M{\"a}rz 2010, [Berlin ; DAGA 2010] / DEGA ... Wiss. Ed. Michael M{\"o}ser ... Band 1}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik}, address = {Berlin}, organization = {Deutsche Jahrestagung f{\"u}r Akustik <36, 2010, Berlin>}, isbn = {978-3-9808659-8-2}, pages = {271 -- 272}, year = {2010}, language = {en} } @inproceedings{GoemmelKraemerButenwegetal.2005, author = {G{\"o}mmel, Andreas and Kr{\"a}mer, Sebastian and Butenweg, Christoph and Kob, Malte}, title = {A combined FE and multiple-mass model for numerical simulation of phonatory maneuvers}, series = {Proceedings / Forum Acusticum, Budapest, 29 Aug - 2 Sep, 2005 : [Acoustics: science and technology for knowledge based society and healthy environment] / ed. by: F{\"u}l{\"o}p Augusztinovicz ...}, booktitle = {Proceedings / Forum Acusticum, Budapest, 29 Aug - 2 Sep, 2005 : [Acoustics: science and technology for knowledge based society and healthy environment] / ed. by: F{\"u}l{\"o}p Augusztinovicz ...}, publisher = {OPAKFI Tud. Egyes{\"u}let}, address = {Budapest}, organization = {Forum Acusticum <4, 2005, Budapest>}, isbn = {978-963-8241-68-9}, pages = {2759 -- 2764}, year = {2005}, language = {en} } @inproceedings{GoemmelKobNiendorfetal.2009, author = {G{\"o}mmel, Andreas and Kob, Malte and Niendorf, Thoralf and Butenweg, Christoph}, title = {An approach for numerical calculation of glottal flow during glottal closure}, series = {Proceedings / NAG/DAGA 2009, International Conference on Acoustics : Rotterdam, 23 - 26 March 2009 ; [including the 35th German Annual Conference on Acoustics (DAGA)] / [organisers: Acoustical Society of the Netherlands (NAG); German Acoustical Society (DEGA) ...]. Ed. by Marinus M. Boone}, booktitle = {Proceedings / NAG/DAGA 2009, International Conference on Acoustics : Rotterdam, 23 - 26 March 2009 ; [including the 35th German Annual Conference on Acoustics (DAGA)] / [organisers: Acoustical Society of the Netherlands (NAG); German Acoustical Society (DEGA) ...]. Ed. by Marinus M. Boone}, publisher = {DEGA}, address = {Berlin}, organization = {NAG DAGA <2009, Rotterdam>}, isbn = {978-3-9808659-6-8}, pages = {1722 -- 1725}, year = {2009}, language = {en} } @inproceedings{GoemmelFrauenrathOttenetal.2010, author = {G{\"o}mmel, Andreas and Frauenrath, Tobias and Otten, Mario and Niendorf, Thoralf and Butenweg, Christoph}, title = {In-vivo measurements of vocal fold geometry using Magnetic Resonance Imaging}, series = {Fortschritte der Akustik - DAGA 2010 36. Jahrestagung f{\"u}r Akustik, 15. bis 18. M{\"a}rz 2010 in Berlin}, booktitle = {Fortschritte der Akustik - DAGA 2010 36. Jahrestagung f{\"u}r Akustik, 15. bis 18. M{\"a}rz 2010 in Berlin}, editor = {M{\"o}ser, Michael and Schulte-Fortkamp, Brgitte and Ochmann, Martin}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik}, address = {Berlin}, isbn = {978-3-9808659-8-2}, year = {2010}, language = {de} } @inproceedings{GoemmelButenwegKob2005, author = {G{\"o}mmel, Andreas and Butenweg, Christoph and Kob, Malte}, title = {Towards a complete finite-element model of human phonation: modeling phonatory maneuvers}, series = {12th Workshop on the Finite Element Method in Biomedical Engineering, Biomechanics and Related Fields : Ulm, Germany, 20 - 21 July 2005 / University of Ulm, Department of Orthodontics ...}, booktitle = {12th Workshop on the Finite Element Method in Biomedical Engineering, Biomechanics and Related Fields : Ulm, Germany, 20 - 21 July 2005 / University of Ulm, Department of Orthodontics ...}, publisher = {Univ., Dep. of Orthodontics}, address = {Ulm}, organization = {Workshop on the Finite Element Method in Biomedical Engineering, Biomechanics and Related Fields <12, 2005, Ulm>}, isbn = {978-3-9806183-8-0}, pages = {1 CD-ROM}, year = {2005}, language = {en} } @article{GoemmelButenwegBolenderetal.2007, author = {G{\"o}mmel, Andreas and Butenweg, Christoph and Bolender, Katrin and Grunendahl, Arno}, title = {A muscle controlled finite-element model of laryngeal abduction and adduction}, series = {Computer methods in biomechanics and biomedical engineering}, volume = {Volume 10}, journal = {Computer methods in biomechanics and biomedical engineering}, number = {Issue 5}, issn = {1476-8259 (E-Journal); 1025-5842 (Print)}, pages = {377 -- 388}, year = {2007}, language = {en} } @inproceedings{GoemmelButenwegKob2007, author = {G{\"o}mmel, A. and Butenweg, Christoph and Kob, M.}, title = {A fluid-structure interaction model of vocal fold oscillation}, series = {5th International Workshop on Models and Analysis of Vocal Emissions for Biomedical Applications, MAVEBA 2007}, booktitle = {5th International Workshop on Models and Analysis of Vocal Emissions for Biomedical Applications, MAVEBA 2007}, isbn = {978-888453674-7}, pages = {127 -- 128}, year = {2007}, abstract = {Since fluid-structure interaction within the finite-element method is state of the art in many engineering fields, this method is used in voice analysis. A quasi two-dimensional model of the vocal folds including the ventricular folds is presented. First results of self-sustained vocal fold oscillation are presented and possibilities as well as limitations are discussed.}, language = {en} } @inproceedings{GrunendahldeRochefortButenweg2005, author = {Grunendahl, A. and de Rochefort, E. and Butenweg, Christoph}, title = {Numerical models for investigating the causes of low back pain due to whole-body vibrations}, series = {2nd International Conference on Computational Bioengineering : Lisbon, September 14-16 2005. Volume 2.}, booktitle = {2nd International Conference on Computational Bioengineering : Lisbon, September 14-16 2005. Volume 2.}, publisher = {IST Press}, address = {Lisbon}, organization = {International Conference on Computational Bioengineering <2, 2005, Lissabon>}, isbn = {978-972-8469-37-3}, pages = {905 -- 914}, year = {2005}, language = {en} } @incollection{GkatzogiasVeljkovivPohorylesetal.2022, author = {Gkatzogias, Konstantinos and Veljkoviv, Ana and Pohoryles, Daniel A. and Tsionis, Georgios and Bournas, Dionysios A. and Crowley, Helen and Norl{\´e}n, Hedvig and Butenweg, Christoph and Gervasio, Helena and Manfredi, Vincenzo and Masi, Angelo and Zaharieva, Roumiana}, title = {Policy practice and regional impact assessment for building renovation}, series = {REEBUILD Integrated Techniques for the Seismic Strengthening \& Energy Efficiency of Existing Buildings}, booktitle = {REEBUILD Integrated Techniques for the Seismic Strengthening \& Energy Efficiency of Existing Buildings}, editor = {Gkatzogias, Konstantinos and Tsionis, Georgios}, publisher = {Publications Office of the European Union}, address = {Luxembourg}, isbn = {978-92-76-60454-9}, issn = {1831-9424}, doi = {10.2760/883122}, pages = {1 -- 68}, year = {2022}, abstract = {The work presented in this report provides scientific support to building renovation policies in the EU by promoting a holistic point of view on the topic. Integrated renovation can be seen as a nexus between European policies on disaster resilience, energy efficiency and circularity in the building sector. An overview of policy measures for the seismic and energy upgrading of buildings across EU Member States identified only a few available measures for combined upgrading. Regulatory framework, financial instruments and digital tools similar to those for energy renovation, together with awareness and training may promote integrated renovation. A framework for regional prioritisation of building renovation was put forward, considering seismic risk, energy efficiency, and socioeconomic vulnerability independently and in an integrated way. Results indicate that prioritisation of building renovation is a multidimensional problem. Depending on priorities, different integrated indicators should be used to inform policies and accomplish the highest relative or most spread impact across different sectors. The framework was further extended to assess the impact of renovation scenarios across the EU with a focus on priority regions. Integrated renovation can provide a risk-proofed, sustainable, and inclusive built environment, presenting an economic benefit in the order of magnitude of the highest benefit among the separate interventions. Furthermore, it presents the unique capability of reducing fatalities and energy consumption at the same time and, depending on the scenario, to a greater extent.}, language = {en} } @article{GiresiniSassuButenwegetal.2017, author = {Giresini, Linda and Sassu, Mauro and Butenweg, Christoph and Alecci, Valerio and De Stefano, Mario}, title = {Vault macro-element with equivalent trusses in global seismic analyses}, series = {Earthquakes and Structures}, volume = {12}, journal = {Earthquakes and Structures}, number = {4}, publisher = {Techno-Press}, address = {Taejŏn}, issn = {2092-7614 (Print)}, doi = {10.12989/eas.2017.12.4.409}, pages = {409 -- 423}, year = {2017}, abstract = {This paper proposes a quick and simplified method to describe masonry vaults in global seismic analyses of buildings. An equivalent macro-element constituted by a set of six trusses, two for each transverse, longitudinal and diagonal direction, is introduced. The equivalent trusses, whose stiffness is calculated by fully modeled vaults of different geometry, mechanical properties and boundary conditions, simulate the vault in both global analysis and local analysis, such as kinematic or rocking approaches. A parametric study was carried out to investigate the influence of geometrical characteristics and mechanical features on the equivalent stiffness values. The method was numerically validated by performing modal and transient analysis on a three naves-church in the elastic range. Vibration modes and displacement time-histories were compared showing satisfying agreement between the complete and the simplified models. This procedure is particularly useful in engineering practice because it allows to assess, in a simplified way, the effectiveness of strengthening interventions for reducing horizontal relative displacements between vault supports.}, language = {en} } @inproceedings{GiresiniButenwegAndreinietal.2014, author = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.}, title = {Numerical calibration of a macro-element for vaultes system in historic churches}, series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, organization = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{GiresiniButenwegAndreinietal.2014, author = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.}, title = {Macro-elements identification in historic chapels: the case of St. Venerio Chapel in Reggiolo - Emilia Romagna}, series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City}, organization = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>}, pages = {1 -- 12}, year = {2014}, language = {en} } @incollection{GiresiniButenweg2019, author = {Giresini, Linda and Butenweg, Christoph}, title = {Earthquake resistant design of structures according to Eurocode 8}, series = {Structural Dynamics with Applications in Earthquake and Wind Engineering}, booktitle = {Structural Dynamics with Applications in Earthquake and Wind Engineering}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-662-57550-5 (Online)}, doi = {10.1007/978-3-662-57550-5_4}, pages = {197 -- 358}, year = {2019}, abstract = {The chapter initially provides a summary of the contents of Eurocode 8, its aim being to offer both to the students and to practising engineers an easy introduction into the calculation and dimensioning procedures of this earthquake code. Specifically, the general rules for earthquake-resistant structures, the definition of design response spectra taking behaviour and importance factors into account, the application of linear and non-linear calculation methods and the structural safety verifications at the serviceability and ultimate limit state are presented. The application of linear and non-linear calculation methods and corresponding seismic design rules is demonstrated on practical examples for reinforced concrete, steel and masonry buildings. Furthermore, the seismic assessment of existing buildings is discussed and illustrated on the example of a typical historical masonry building in Italy. The examples are worked out in detail and each step of the design process, from the preliminary analysis to the final design, is explained in detail.}, language = {en} } @inproceedings{GellertParkButenweg2010, author = {Gellert, Christoph and Park, Jin and Butenweg, Christoph}, title = {Seismic safety verification of masonry structures}, series = {Proceedings of the Eight International Masonry Conference : held in Dresden from 4th to 7th of July 2010 / [International Masonry Society ; Technische Universit{\"a}t Dresden]. Ed. by: Wolfram J{\"a}ger ... Volume 1. (Masonry / International Masonry Society Special Publication ; 11)}, booktitle = {Proceedings of the Eight International Masonry Conference : held in Dresden from 4th to 7th of July 2010 / [International Masonry Society ; Technische Universit{\"a}t Dresden]. Ed. by: Wolfram J{\"a}ger ... Volume 1. (Masonry / International Masonry Society Special Publication ; 11)}, publisher = {ARGE 8IMC Dresden}, address = {Radebeul}, organization = {International Masonry Conference <8, 2010, Dresden>}, isbn = {978-3-00-031381-3}, pages = {813 -- 822}, year = {2010}, language = {en} } @inproceedings{GellertNordaButenweg2008, author = {Gellert, Christoph and Norda, Hannah and Butenweg, Christoph}, title = {Nonlinear behaviour of masonry under cyclic loading}, series = {7th European Conference on Structural Dynamics, EURODYN 2008 : 7-9 July 2008, Southampton}, booktitle = {7th European Conference on Structural Dynamics, EURODYN 2008 : 7-9 July 2008, Southampton}, organization = {European Conference on Structural Dynamics, EURODYN <7, 2008, Southampton>}, pages = {1 -- 12}, year = {2008}, language = {en} } @article{GellertButenweg2014, author = {Gellert, Christoph and Butenweg, Christoph}, title = {Seismic analysis of masonry structures in German earthquake zones according to DIN EN 1998-1}, series = {Mauerwerk : European journal of masonry}, volume = {18}, journal = {Mauerwerk : European journal of masonry}, number = {3-4}, publisher = {Ernst \& Sohn}, address = {Berlin}, issn = {1437-1022 (E-Journal); 1432-3427 (Print)}, doi = {10.1002/dama.201400626}, pages = {188 -- 196}, year = {2014}, abstract = {Die Erdbeben in Albstadt 1978 (Magnitude 5,7), Roermond 1992 (Magnitude 5,9) oder in Waldkirch 2004 (Magnitude 5,1) haben verdeutlicht, dass die erdbebensichere Auslegung von Mauerwerksbauten auch in Deutschland von großer Bedeutung ist. Bereits im Jahr 1981 wurde die DIN 4149 (1981) "Bauten in deutschen Erdbebengebieten - Lastannahmen, Bemessung und Ausf{\"u}hrung {\"u}blicher Hochbauten" eingef{\"u}hrt, in der aber f{\"u}r Mauerwerksbauten nur wenige Anforderungen gestellt wurden. Diese Norm wurde durch den NABau-Arbeitsausschuss "Erdbeben; Sonderfragen" des Deutschen Instituts f{\"u}r Normung e.V. (DIN) auf Grundlage des Eurocode 8 (2004) vollst{\"a}ndig {\"u}berarbeitet und durch die DIN 4149 (2005) abgel{\"o}st, die umfangreiche Regelungen f{\"u}r die seismische Auslegung von Mauerwerksbauten enth{\"a}lt. Mittlerweile liegen die DIN EN 1998-1 (2010) und der Nationale Anhang DIN EN 1998-1/NA (2011) vor, die nach Einarbeitung der Ergebnisse der durchgef{\"u}hrten Anwendungserprobung bauaufsichtlich eingef{\"u}hrt und die DIN 4149 (2005) ersetzen werden. Der folgende Beitrag gibt einen {\"U}berblick {\"u}ber die seismische Berechnung und Bemessung von Mauerwerksbauten nach dem europ{\"a}ischen Regelwerk und illustriert deren Anwendung an einem baupraktischen Beispiel.}, language = {de} } @inproceedings{GellertButenweg2009, author = {Gellert, Christoph and Butenweg, Christoph}, title = {Nichtlinearer Erdbebennachweis von Mauerwerksbauten}, series = {Erdbeben und Mauerwerk : 11. D-A-CH-Tagung 2009 ; [10./11. September 2009 in Z{\"u}rich] / SGEB, Swiss Society for Earthquake Engineering and Structural Dynamics; Schweizerischer Ingenieur- und Architektenverein, Fachgruppe f{\"u}r Br{\"u}ckenbau und Hochbau. [Hrsg. Dazio, Alessandro ...]}, booktitle = {Erdbeben und Mauerwerk : 11. D-A-CH-Tagung 2009 ; [10./11. September 2009 in Z{\"u}rich] / SGEB, Swiss Society for Earthquake Engineering and Structural Dynamics; Schweizerischer Ingenieur- und Architektenverein, Fachgruppe f{\"u}r Br{\"u}ckenbau und Hochbau. [Hrsg. Dazio, Alessandro ...]}, publisher = {SIA}, address = {Z{\"u}rich}, organization = {D-A-C-H Tagung <11, 2009, Z{\"u}rich>}, isbn = {978-3-03732-021-1}, pages = {125 -- 132}, year = {2009}, language = {de} } @article{FrauenrathHezelHeinrichsetal.2009, author = {Frauenrath, Tobias and Hezel, Fabian and Heinrichs, Uwe and Kozerke, Sebastian and Utting, Jane and Kob, Malte and Butenweg, Christoph and Boesiger, Peter and Niendorf, Thoralf}, title = {Feasibility of Cardiac Gating Free of Interference With Electro-Magnetic Fields at 1.5 Tesla, 3.0 Tesla and 7.0 Tesla Using an MR-Stethoscope}, series = {Investigative Radiology}, volume = {44}, journal = {Investigative Radiology}, number = {9}, publisher = {Lippincott Williams \& Wilkins ; (via Ovid)}, address = {Philadelphia, Pa}, issn = {1536-0210 (online)}, doi = {10.1097/RLI.0b013e3181b4c15e}, pages = {539 -- 547}, year = {2009}, language = {en} } @inproceedings{FrauenrathGoemmelButenwegetal.2010, author = {Frauenrath, Tobias and G{\"o}mmel, Andreas and Butenweg, Christoph and Otten, Mario and Niendorf, Thoralf}, title = {3D mapping of vocal fold geometry during articulatory maneuvers using ultrashort echo time imaging at 3.0 T}, series = {ISMRM-ESMRMB joint annual meeting 2010 : Stockholm, Sweden, 1 - 7 May 2010. Band 4}, booktitle = {ISMRM-ESMRMB joint annual meeting 2010 : Stockholm, Sweden, 1 - 7 May 2010. Band 4}, publisher = {Curran}, address = {Red Hook, NY}, organization = {International Society of Magnetic Resonance in Medicine}, isbn = {978-1-617-82008-3}, pages = {3087}, year = {2010}, language = {en} } @inproceedings{ElDeibChudobaButenwegetal.2002, author = {El-Deib, Khaled and Chudoba, Rostislav and Butenweg, Christoph and Meskouris, Konstantin and K{\"o}nke, Carsten and Bettzieche, Volker}, title = {Safety assessment of rockfill and masonry dams}, series = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ... Vol. 1}, booktitle = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ... Vol. 1}, publisher = {Balkema}, address = {Lisse}, organization = {International Conference on Structural Dynamics <5, 2002, M{\"u}nchen>}, isbn = {90-5809-510-X}, pages = {237 -- 242}, year = {2002}, language = {en} } @article{ElDeibButenwegKlinkel2020, author = {El-Deib, Khaled and Butenweg, Christoph and Klinkel, Sven}, title = {Erdbebennachweis von Mauerwerksbauten mit realistischen Modellen und erh{\"o}hten Verhaltensbeiwerten}, series = {Bautechnik}, volume = {97}, journal = {Bautechnik}, number = {11}, publisher = {Ernst \& Sohn}, address = {Berlin}, doi = {10.1002/bate.202000016}, pages = {756 -- 765}, year = {2020}, abstract = {Die Anwendung des linearen Nachweiskonzepts auf Mauerwerksbauten f{\"u}hrt dazu, dass bereits heute Standsicherheitsnachweise f{\"u}r Geb{\"a}ude mit {\"u}blichen Grundrissen in Gebieten mit moderaten Erdbebeneinwirkungen nicht mehr gef{\"u}hrt werden k{\"o}nnen. Diese Problematik wird sich in Deutschland mit der Einf{\"u}hrung kontinuierlicher probabilistischer Erdbebenkarten weiter versch{\"a}rfen. Aufgrund der Erh{\"o}hung der seismischen Einwirkungen, die sich vielerorts ergibt, ist es erforderlich, die vorhandenen, bislang nicht ber{\"u}cksichtigten Tragf{\"a}higkeitsreserven in nachvollziehbaren Nachweiskonzepten in der Baupraxis verf{\"u}gbar zu machen. Der vorliegende Beitrag stellt ein Konzept f{\"u}r die geb{\"a}udespezifische Ermittlung von erh{\"o}hten Verhaltensbeiwerten vor. Die Verhaltensbeiwerte setzen sich aus drei Anteilen zusammen, mit denen die Lastumverteilung im Grundriss, die Verformungsf{\"a}higkeit und Energiedissipation sowie die {\"U}berfestigkeiten ber{\"u}cksichtigt werden. F{\"u}r die rechnerische Ermittlung dieser drei Anteile wird ein nichtlineares Nachweiskonzept auf Grundlage von Pushover-Analysen vorgeschlagen, in denen die Interaktionen von W{\"a}nden und Geschossdecken durch einen Einspanngrad beschrieben werden. F{\"u}r die Bestimmung der Einspanngrade wird ein nichtlinearer Modellierungsansatz eingef{\"u}hrt, mit dem die Interaktion von W{\"a}nden und Decken abgebildet werden kann. Die Anwendung des Konzepts mit erh{\"o}hten geb{\"a}udespezifischen Verhaltensbeiwerten wird am Beispiel eines Mehrfamilienhauses aus Kalksandsteinen demonstriert. Die Ergebnisse der linearen Nachweise mit erh{\"o}hten Verhaltensbeiwerten f{\"u}r dieses Geb{\"a}ude liegen deutlich n{\"a}her an den Ergebnissen nichtlinearer Nachweise und somit bleiben {\"u}bliche Grundrisse in Erdbebengebieten mit den traditionellen linearen Rechenans{\"a}tzen nachweisbar.}, language = {de} } @article{ElDeibButenwegKlinkel2021, author = {El-Deib, Khaled and Butenweg, Christoph and Klinkel, Sven}, title = {Erdbebennachweis von Mauerwerksbauten mit realistischen Modellen und erh{\"o}hten Verhaltensbeiwerten}, series = {Mauerwerk}, volume = {2021}, journal = {Mauerwerk}, number = {3}, editor = {Jesse, Dirk}, publisher = {Wiley}, address = {Weinheim}, issn = {1437-1022}, doi = {10.1002/dama.202110014}, pages = {110 -- 119}, year = {2021}, abstract = {Die Anwendung des linearen Nachweiskonzepts auf Mauerwerksbauten f{\"u}hrt dazu, dass bereits heute Standsicherheitsnachweise f{\"u}r Geb{\"a}ude mit {\"u}blichen Grundrissen in Gebieten mit moderaten Erdbebeneinwirkungen nicht mehr gef{\"u}hrt werden k{\"o}nnen. Diese Problematik wird sich in Deutschland mit der Einf{\"u}hrung kontinuierlicher probabilistischer Erdbebenkarten weiter versch{\"a}rfen. Aufgrund der Erh{\"o}hung der seismischen Einwirkungen, die sich vielerorts ergibt, ist es erforderlich, die vorhandenen, bislang nicht ber{\"u}cksichtigten Tragf{\"a}higkeitsreserven in nachvollziehbaren Nachweiskonzepten in der Baupraxis verf{\"u}gbar zu machen. Der vorliegende Beitrag stellt ein Konzept f{\"u}r die geb{\"a}udespezifische Ermittlung von erh{\"o}hten Verhaltensbeiwerten vor. Die Verhaltensbeiwerte setzen sich aus drei Anteilen zusammen, mit denen die Lastumverteilung im Grundriss, die Verformungsf{\"a}higkeit und Energiedissipation sowie die {\"U}berfestigkeiten ber{\"u}cksichtigt werden. F{\"u}r die rechnerische Ermittlung dieser drei Anteile wird ein nichtlineares Nachweiskonzept auf Grundlage von Pushover-Analysen vorgeschlagen, in denen die Interaktionen von W{\"a}nden und Geschossdecken durch einen Einspanngrad beschrieben werden. F{\"u}r die Bestimmung der Einspanngrade wird ein nichtlinearer Modellierungsansatz eingef{\"u}hrt, mit dem die Interaktion von W{\"a}nden und Decken abgebildet werden kann. Die Anwendung des Konzepts mit erh{\"o}hten geb{\"a}udespezifischen Verhaltensbeiwerten wird am Beispiel eines Mehrfamilienhauses aus Kalksandsteinen demonstriert. Die Ergebnisse der linearen Nachweise mit erh{\"o}hten Verhaltensbeiwerten f{\"u}r dieses Geb{\"a}ude liegen deutlich n{\"a}her an den Ergebnissen nichtlinearer Nachweise und somit bleiben {\"u}bliche Grundrisse in Erdbebengebieten mit den traditionellen linearen Rechenans{\"a}tzen nachweisbar.}, language = {de} } @inproceedings{EdipGarevskiButenwegetal.2014, author = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sheshov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor}, title = {New coupled finite-infinite element approach for wave propagation simulation of unbounded soil media}, series = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2}, booktitle = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2}, publisher = {Curran Associates, Inc.}, address = {Red Hook, NY}, organization = {European Conference on Earthquake Engineering and Seismology <2, 2014, Istanbul>}, isbn = {978-1-5108-1021-1}, pages = {1556 -- 1561}, year = {2014}, language = {en} } @article{EdipGarevskiButenwegetal.2013, author = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sesov, Vlatko and Cvetanovska, Julijana and Gjorgiev, Igor}, title = {Numerical simulation of geotechnical problems by coupled finite and infinite elements}, series = {Journal of civil engineering and architecture}, volume = {7}, journal = {Journal of civil engineering and architecture}, number = {1}, publisher = {David Publishing}, address = {Libertyville}, issn = {1934-7359 (E-Journal)}, pages = {68 -- 77}, year = {2013}, language = {en} } @inproceedings{EdipGarevskiButenwegetal.2014, author = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sesov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor}, title = {Boundary effects on seismic analysis of multi-storey frames considering soil structure interaction phenomenon}, series = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed}, booktitle = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed}, publisher = {Springer Vieweg}, address = {Wiesbaden}, organization = {International Conference on Seismic Design of Industrial Facilities <2013, Aachen>}, isbn = {978-3-658-02809-1 (Print) ; 978-3-658-02810-7}, doi = {10.1007/978-3-658-02810-7_47}, pages = {569 -- 576}, year = {2014}, language = {en} } @article{EdipSesovButenwegetal.2018, author = {Edip, K. and Sesov, V. and Butenweg, Christoph and Bojadjieva, J.}, title = {Development of coupled numerical model for simulation of multiphase soil}, series = {Computers and Geotechnics}, volume = {96}, journal = {Computers and Geotechnics}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0266-352X}, doi = {10.1016/j.compgeo.2017.08.016}, pages = {118 -- 131}, year = {2018}, abstract = {In this paper, a coupled multiphase model considering both non-linearities of water retention curves and solid state modeling is proposed. The solid displacements and the pressures of both water and air phases are unknowns of the proposed model. The finite element method is used to solve the governing differential equations. The proposed method is demonstrated through simulation of seepage test and partially consolidation problem. Then, implementation of the model is done by using hypoplasticity for the solid phase and analyzing the fully saturated triaxial experiments. In integration of the constitutive law error controlling is improved and comparisons done accordingly. In this work, the advantages and limitations of the numerical model are discussed.}, language = {en} } @inproceedings{DalguerRenaultChurilovetal.2016, author = {Dalguer, Luis A. and Renault, Philippe and Churilov, Sergey and Butenweg, Christoph}, title = {Evaluation of fragility curves for a three-storey-reinforced-concrete mock-up of SMART 2013 project}, series = {Transactions, SMiRT-23 : 23rd Conference on Structural Mechanics in Reactor Technology : Manchester, United Kingdom - August 10-14, 2015}, booktitle = {Transactions, SMiRT-23 : 23rd Conference on Structural Mechanics in Reactor Technology : Manchester, United Kingdom - August 10-14, 2015}, organization = {Conference on Structural Mechanics in Reactor Technology <23, 2015, Manchester>}, pages = {1 -- 9}, year = {2016}, language = {en} } @inproceedings{DalguerChurilovButenwegetal.2014, author = {Dalguer, Luis A. and Churilov, Sergey and Butenweg, Christoph and Renault, Philippe and Hyun, An Jun}, title = {Dynamic analysis of a reinforced concrete electrical nuclear building of SMART 2013 project subjected to earthquake excitation using ABAQUS}, series = {Workshop SMART2013 : Paris, France, November 25th - 27th, 2014}, booktitle = {Workshop SMART2013 : Paris, France, November 25th - 27th, 2014}, organization = {Workshop SMART2013 <2014, Paris>}, pages = {1 -- 12}, year = {2014}, language = {en} } @inproceedings{ChurilovDumovaJovanoskaButenweg2013, author = {Churilov, Sergej and Dumova-Jovanoska, Elena and Butenweg, Christoph}, title = {Seismic verification of existing masonry buildings and strengthening with reinforced concrete jackets}, series = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)}, booktitle = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)}, editor = {Adam, Christoph and Heuer, Rudolf and Lenhardt, Wolfgang and Schranz, Christian}, isbn = {978-3-902749-04-8}, year = {2013}, abstract = {A methodology for assessment, seismic verification and strengthening of existing masonry buildings is presented in this paper. The verification is performed using a calculation model calibrated with the results from ambient vibration measurements. The calibrated model serves as an input for a deformation-based verification procedure based on the Capacity Spectrum Method (CSM). The bearing capacity of the building is calculated from experimental capacity curves of the individual walls idealized with bilinear elastic-perfectly plastic curves. The experimental capacity curves were obtained from in-plane cyclic loading tests on unreinforced and strengthened masonry walls with reinforced concrete jackets. The seismic action is compared with the load-bearing capacity of the building considering non-linear material behavior with its post-peak capacity. The application of the CSM to masonry buildings and the influence of a traditional strengthening method are demonstrated on the example of a public school building in Skopje, Macedonia.}, language = {en} } @article{ChudobaKuhlmannButenweg2001, author = {Chudoba, Rostislav and Kuhlmann, Wolfram and Butenweg, Christoph}, title = {Ein technisches Informationssystem zur Entwicklung von Textilbeton}, series = {Bauinformatik-Journal : bi-Journal; Zeitschrift f{\"u}r Architekten und Ingenieure}, volume = {Bd. 4}, journal = {Bauinformatik-Journal : bi-Journal; Zeitschrift f{\"u}r Architekten und Ingenieure}, number = {H. 6}, issn = {1436-9060}, pages = {15 -- 20}, year = {2001}, language = {de} } @inproceedings{ChudobaKuhlmannButenweg2001, author = {Chudoba, Rostislav and Kuhlmann, Wolfram and Butenweg, Christoph}, title = {Ein internetbasiertes technisches Informationssystem zur Koordination und Pr{\"a}sentation des Sonderforschungsbereichs 532}, series = {Forum Bauinformatik 2001 - Junge Wissenschaftler Forschen / Richard Romberg .̤ (Hrsg.) (Fortschrittberichte VDI : Reihe 4, Bauingenieurwesen ; Nr. 169)}, booktitle = {Forum Bauinformatik 2001 - Junge Wissenschaftler Forschen / Richard Romberg .̤ (Hrsg.) (Fortschrittberichte VDI : Reihe 4, Bauingenieurwesen ; Nr. 169)}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, organization = {Forum Bauinformatik <2001>}, isbn = {3-18-316904-5}, pages = {94 -- 101}, year = {2001}, language = {de} } @inproceedings{ChudobaButenwegPfeiffer2003, author = {Chudoba, Rostislav and Butenweg, Christoph and Pfeiffer, Frank}, title = {Textile reinforced concrete. Part I: Process model for collaborative research and development}, series = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke}, booktitle = {Digital proceedings / IKM 2003, proceedings 16th International Conference on the Applications of Computer Science and Mathematics in Architecture and Civil Engineering [Elektronische Ressource : 10. - 12. Juni 2003, Weimar] / Bauhaus-Universit{\"a}t Weimar. Ed.: K. G{\"u}rlebeck; L. Hempel; C. K{\"o}nke}, publisher = {IKM}, address = {Weimar}, organization = {Internationales Kolloquium {\"u}ber Anwendungen der Informatik und Mathematik in Architektur und Bauwesen <16, 2003, Weimar>}, pages = {1 -- 8}, year = {2003}, language = {en} } @article{ChudobaButenwegPeiffer2004, author = {Chudoba, Rostislav and Butenweg, Christoph and Peiffer, F.}, title = {Technical information system for collaborative material research}, series = {Advances in engineering software}, volume = {Volume 35}, journal = {Advances in engineering software}, number = {Issue 10-11}, issn = {1873-5339 (E-Journal); 0965-9978 (Print)}, doi = {10.1016/j.advengsoft.2004.03.021}, pages = {747 -- 756}, year = {2004}, language = {en} } @inproceedings{ChudobaButenwegKuhlmann2002, author = {Chudoba, Rostislav and Butenweg, Christoph and Kuhlmann, Wolfram}, title = {Technical information system for collaborative material research}, series = {Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002]}, booktitle = {Sixth International Conference on Computational Structures Technology : [Prague, Czech Republic, 4 - 6 September 2002]}, organization = {International Conference on Computational Structures Technology <6, 2002, Prag>}, pages = {1 -- 11}, year = {2002}, language = {en} } @inproceedings{CacciatoreButenweg2020, author = {Cacciatore, Pamela and Butenweg, Christoph}, title = {Seismic safety of cylindrical granular material steel silos under seismic loading}, series = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)}, booktitle = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)}, isbn = {978-3-86359-729-0}, pages = {231 -- 244}, year = {2020}, language = {en} } @inproceedings{ButenwegThierauf1996, author = {Butenweg, Christoph and Thierauf, Georg}, title = {Erfahrungen bei der Entwicklung eines objekt-orientierten FE-Programmes}, series = {Forum Bauinformatik - Junge Wissenschaftler Forschen : Cottbus '96 / Olaf Horstmann ... (Hrsg.) (Fortschrittberichte VDI : Reihe 4, Bauingenieurwesen ; 135)}, booktitle = {Forum Bauinformatik - Junge Wissenschaftler Forschen : Cottbus '96 / Olaf Horstmann ... (Hrsg.) (Fortschrittberichte VDI : Reihe 4, Bauingenieurwesen ; 135)}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, isbn = {3-18-313504-3}, pages = {60 -- 65}, year = {1996}, language = {de} } @inproceedings{ButenwegThierauf1997, author = {Butenweg, Christoph and Thierauf, Georg}, title = {Optimum cost design of reinforced concrete structures using parallel computing}, series = {Advances in computational mechanics with parallel and distributed processing : research papers presented at The First Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held at Lochinver, Scotland, between 26 April and 1 May 1997 / ed. by B. H. V. Topping}, booktitle = {Advances in computational mechanics with parallel and distributed processing : research papers presented at The First Euro-Conference on Parallel and Distributed Computing for Computational Mechanics, held at Lochinver, Scotland, between 26 April and 1 May 1997 / ed. by B. H. V. Topping}, publisher = {Saxe-Coburg Publication}, address = {Edinburgh}, organization = {Euro-Conference on Parallel and Distributed Computing for Computational Mechanics <1, 1997, Lochinver, Scotland>}, isbn = {0-948749-47-4}, pages = {197 -- 202}, year = {1997}, language = {en} } @inproceedings{ButenwegThierauf1998, author = {Butenweg, Christoph and Thierauf, Georg}, title = {Optimum design of reinforced concrete structures}, series = {Advances in computational structural mechanics : this volume contains a selection of papers presented at The First International Conference on Engineering Computational Technology and The Fourth International Conference on Computational Structures Technology, held in Edinburgh from 18-21 August 1998 / edited by B. H. V. Topping}, booktitle = {Advances in computational structural mechanics : this volume contains a selection of papers presented at The First International Conference on Engineering Computational Technology and The Fourth International Conference on Computational Structures Technology, held in Edinburgh from 18-21 August 1998 / edited by B. H. V. Topping}, publisher = {Civil-Comp Press}, address = {Edinburgh}, organization = {International Conference on Computational Structures Technology <4, 1998, Edinburgh>}, isbn = {0-948749-57-1}, pages = {447 -- 458}, year = {1998}, language = {en} } @inproceedings{ButenwegThierauf1999, author = {Butenweg, Christoph and Thierauf, Georg}, title = {Bemessung und Kostenoptimierung von Stahlbetontragwerken}, series = {Berichte der 7. Fachtagung "Baustatik - Baupraxis" : Aachen, Deutschland, 18. - 19. M{\"a}rz 1999 / Hrsg.: Konstantin Meskouris. (Baustatik Baupraxis ; 7)}, booktitle = {Berichte der 7. Fachtagung "Baustatik - Baupraxis" : Aachen, Deutschland, 18. - 19. M{\"a}rz 1999 / Hrsg.: Konstantin Meskouris. (Baustatik Baupraxis ; 7)}, publisher = {Balkema}, address = {Rotterdam}, organization = {Fachtagung Baustatik, Baupraxis <7, 1999, Aachen>}, isbn = {90-5809-044-2}, pages = {213 -- 220}, year = {1999}, language = {de} } @incollection{ButenwegThierauf1999, author = {Butenweg, Christoph and Thierauf, G.}, title = {Automatic design of reinforced concrete structures with parallel computing}, series = {Innovative computational methods for structural mechanics}, booktitle = {Innovative computational methods for structural mechanics}, editor = {Papadrakakis, M. and Topping, B.H.V.}, publisher = {Saxe-Coburg Publication}, address = {Edinburgh}, isbn = {1-874672-05-9}, doi = {10.4203/csets.1.14}, pages = {305 -- 318}, year = {1999}, abstract = {A concept for the analysis and optimal design of reinforced concrete structures is described. It is based on a nonlinear optimization algorithm and a finite element program for linear and nonlinear analysis of structures. With the aim of minimal cost design a two stage optimization using efficient gradient algorithm is developed. The optimization problems on global (structural) and local (crosssectional) level are formulated. A parallelization concept for solving the two stage optimization problem in minimal time is presented. Examples are included to illustrate the practical use and the effectively of the parallelization in the area of engineering design.}, language = {en} } @article{ButenwegSchmittRosen2014, author = {Butenweg, Christoph and Schmitt, Timo and Rosen, Britta}, title = {Seismische Einwirkungen auf erdverlegte Rohrleitungssysteme}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik}, volume = {89 (2014)}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik}, number = {Heft 7/8}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {316 -- 324}, year = {2014}, language = {de} } @article{ButenwegSchmittRosen2014, author = {Butenweg, Christoph and Schmitt, T. and Rosen, B.}, title = {Seismische Einwirkungen auf erdverlegte Rohrleitungen}, series = {Bauingenieur}, volume = {89}, journal = {Bauingenieur}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {316 -- 324}, year = {2014}, abstract = {Die erdbebensichere Auslegung von erdverlegten Rohrleitungssystemen ist von wesentlicher Bedeutung zur Sicherstellung der Funktionalit{\"a}t der Versorgungsinfrastruktur nach einem Erdbebenereignis. Zur Vermeidung von Netzausf{\"a}llen ist es erforderlich, die r{\"a}umlich weit ausgedehnten Leitungssysteme mit geeigneten rechnerischen Modellen seismisch zu bemessen. Der vorliegende Beitrag behandelt die Beanspruchung von Rohrleitungssystemen durch seismische Welleneinwirkung und stellt geeignete N{\"a}herungsans{\"a}tze und ein detailliertes Rechenmodell f{\"u}r seismische Leitungsanalysen vor. Mit den Ans{\"a}tzen wird in Berechnungsbeispielen der Einfluss wesentlicher Parameter auf die seismisch induzierten Dehnungen in Rohrleitungssystemen untersucht.}, language = {de} } @inproceedings{ButenwegSadeghAzarMeskouris2004, author = {Butenweg, Christoph and Sadegh-Azar, H. and Meskouris, Konstantin}, title = {Seismische Vulnerabilit{\"a}t von bestehenden Bauwerken}, series = {5. Forum und Gefahrentag : auf der Suche nach dem Risiko : ein aktuelles Symposium zu Fragen der Risikowahrnehmung und Katastrophenvorsorge in Deutschland, ZDF Mainz Lerchenberg, 13. - 14. Oktober, 2004}, booktitle = {5. Forum und Gefahrentag : auf der Suche nach dem Risiko : ein aktuelles Symposium zu Fragen der Risikowahrnehmung und Katastrophenvorsorge in Deutschland, ZDF Mainz Lerchenberg, 13. - 14. Oktober, 2004}, pages = {1}, year = {2004}, language = {de} } @inproceedings{ButenwegRosinKubalski2013, author = {Butenweg, Christoph and Rosin, Julia and Kubalski, Thomas}, title = {Seismic response of conventional and base-isolated liquid storage tanks}, series = {International Conference on Earthquake Engineering : 29.-31.05.2013, Skopje, Mazedonien}, booktitle = {International Conference on Earthquake Engineering : 29.-31.05.2013, Skopje, Mazedonien}, organization = {International Conference on Earthquake Engineering <2013, Skopje>}, pages = {1 -- 8}, year = {2013}, language = {en} } @article{ButenwegRosinHoller2017, author = {Butenweg, Christoph and Rosin, Julia and Holler, Stefan}, title = {Analysis of cylindrical granular material silos under seismic excitation}, series = {Buildings}, volume = {7}, journal = {Buildings}, number = {3}, publisher = {MDPI}, address = {Basel}, issn = {2075-5309}, doi = {10.3390/buildings7030061}, pages = {1 -- 12}, year = {2017}, abstract = {Silos generally work as storage structures between supply and demand for various goods, and their structural safety has long been of interest to the civil engineering profession. This is especially true for dynamically loaded silos, e.g., in case of seismic excitation. Particularly thin-walled cylindrical silos are highly vulnerable to seismic induced pressures, which can cause critical buckling phenomena of the silo shell. The analysis of silos can be carried out in two different ways. In the first, the seismic loading is modeled through statically equivalent loads acting on the shell. Alternatively, a time history analysis might be carried out, in which nonlinear phenomena due to the filling as well as the interaction between the shell and the granular material are taken into account. The paper presents a comparison of these approaches. The model used for the nonlinear time history analysis considers the granular material by means of the intergranular strain approach for hypoplasticity theory. The interaction effects between the granular material and the shell is represented by contact elements. Additionally, soil-structure interaction effects are taken into account.}, language = {en} } @article{ButenwegRosin2020, author = {Butenweg, Christoph and Rosin, Julia}, title = {Seismischer Nachweis von Mauerwerksbauten in deutschen Erdbebengebieten}, series = {Mauerwerk}, volume = {24}, journal = {Mauerwerk}, number = {2}, publisher = {Wiley}, address = {Weinheim}, issn = {1437-1022}, doi = {10.1002/dama.202000006}, pages = {108 -- 113}, year = {2020}, abstract = {Mit finanzieller Unterst{\"u}tzung der Deutschen Gesellschaft f{\"u}r Mauerwerks- und Wohnungsbau e.V. (DGfM) und des Deutschen Instituts f{\"u}r Bautechnik in Berlin (DIBt) wurden zwei aufeinander aufbauende Forschungsvorhaben zur Verbesserung der seismischen Nachweise von Mauerwerksbauten in deutschen Erdbebengebieten durchgef{\"u}hrt. Zun{\"a}chst wurde das seismische Verhalten von drei modernen unbewehrten Mauerwerksgeb{\"a}uden in der Region Emilia Romagna in Italien w{\"a}hrend der Erdbebenserie im Jahr 2012 in Kooperation mit der Universit{\"a}t Pavia eingehend untersucht. Aufbauend auf den Erkenntnissen dieser Untersuchungen wurde ein verbessertes seismisches Bemessungskonzept f{\"u}r unbewehrte Mauerwerksbauten erarbeitet. Der Beitrag stellt die wesentlichen Ergebnisse dieser Forschungsarbeiten und deren Eingang in die Normung vor.}, language = {de} } @incollection{ButenwegRoeser2012, author = {Butenweg, Christoph and Roeser, W.}, title = {Erdbebenbemessung von Stahlbetontragwerken nach DIN EN 1998-1}, series = {Stahlbetonbau aktuell : Praxishandbuch}, booktitle = {Stahlbetonbau aktuell : Praxishandbuch}, publisher = {Beuth}, address = {Berlin}, isbn = {978-3-410-21932-3 (Print) ; 978-341-02193-3-0 (E-Book)}, pages = {A.1 -- A.43}, year = {2012}, language = {de} } @incollection{ButenwegRoeser2016, author = {Butenweg, Christoph and Roeser, W.}, title = {Auslegung von Bauwerken gegen Erdbeben - Rechenbeispiele}, series = {Stahlbetonbau aktuell 2016 : Praxishandbuch / herausgegeben von: Prof. Dr.-Ing. Josef Hegger, Prof. Dr.-Ing. habil. Peter Mark}, booktitle = {Stahlbetonbau aktuell 2016 : Praxishandbuch / herausgegeben von: Prof. Dr.-Ing. Josef Hegger, Prof. Dr.-Ing. habil. Peter Mark}, publisher = {Beuth Verlag GmbH}, address = {Berlin ; Wien ; Z{\"u}rich}, isbn = {978-3-410-25202-3 (Print) ; 978-3-410-25203-0 (E-Book)}, year = {2016}, language = {de} } @article{ButenwegRenault2014, author = {Butenweg, Christoph and Renault, Philippe}, title = {Workshop der Gesellschaften zum EU-Projekt SHARE}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, volume = {89 (2014)}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, number = {Oktober}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {1436-4867 (E-Journal); 0005-6650 (Print)}, pages = {S2 -- S3}, year = {2014}, language = {de} } @inproceedings{ButenwegRajan2014, author = {Butenweg, Christoph and Rajan, Sreelakshmy}, title = {Design and construction techniques of AAC masonry buildings in earthquakes regions}, series = {10 years Xella research in Building Materials : Symposium on the 4th and 5th of September, Potsdam 2014}, booktitle = {10 years Xella research in Building Materials : Symposium on the 4th and 5th of September, Potsdam 2014}, year = {2014}, language = {en} } @inproceedings{ButenwegPark2011, author = {Butenweg, Christoph and Park, Jin}, title = {Verhalten von Ankerschienensystemen unter statisch zyklischen Beanspruchungen}, series = {12. D-A-CH Tagung 2011 : Erdbeben und Baudynamik ; 15./16. September 2011, Hannover, Deutschland / Bundesanstalt f{\"u}r Geowissenschaften und Rohstoffe. C. K{\"o}nke (Hrsg.)}, booktitle = {12. D-A-CH Tagung 2011 : Erdbeben und Baudynamik ; 15./16. September 2011, Hannover, Deutschland / Bundesanstalt f{\"u}r Geowissenschaften und Rohstoffe. C. K{\"o}nke (Hrsg.)}, address = {Deutsche Gesellschaft f{\"u}r Erdbebeningenieurwesen und Baudynamik}, organization = {D-A-C-H Tagung <12, 2011, Hannover>}, isbn = {3-930108-11-9}, pages = {349 -- 365}, year = {2011}, language = {de} } @inproceedings{ButenwegNorda2013, author = {Butenweg, Christoph and Norda, Hannah}, title = {Nonlinear analysis of masonry structures according to Eurocode 8}, series = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)}, booktitle = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)}, editor = {Adam, Christoph and Heuer, Rudolf and Lenhardt, Wolfgang and Schranz, Christian}, isbn = {978-3-902749-04-8}, year = {2013}, language = {en} } @incollection{ButenwegNorda2014, author = {Butenweg, Christoph and Norda, H.}, title = {Erdbebenberechnung von Mauerwerksbauten nach DIN EN 1998-1:2010-12}, series = {Mauerwerksbau-Praxis nach Eurocode / Schubert, Schneider, Schoch (Hrsg.). - 3., vollst{\"a}ndig {\"u}berarbeitete Auflage}, booktitle = {Mauerwerksbau-Praxis nach Eurocode / Schubert, Schneider, Schoch (Hrsg.). - 3., vollst{\"a}ndig {\"u}berarbeitete Auflage}, publisher = {Beuth}, address = {Berlin, Wien, Z{\"u}rich}, isbn = {978-3-410-22739-7}, pages = {367 -- 412}, year = {2014}, language = {de} } @inproceedings{ButenwegMistler2006, author = {Butenweg, Christoph and Mistler, Michael}, title = {Seismic resistance of unreinforced masonry buildings}, series = {Proceedings of the Eighth International Conference on Computational Structures Technology : [Las Palmas de Cran Canaria, 12-15 September 2006] / ed. by B. H. V. Topping ...}, booktitle = {Proceedings of the Eighth International Conference on Computational Structures Technology : [Las Palmas de Cran Canaria, 12-15 September 2006] / ed. by B. H. V. Topping ...}, publisher = {Civil-Comp Press}, address = {Stirling}, organization = {International Conference on Computational Structures Technology <8, 2006, Las Palmas>}, isbn = {1-905088-06-X}, doi = {10.4203/ccp.83.9}, pages = {Paper 9}, year = {2006}, language = {en} } @article{ButenwegMeyerFehling2014, author = {Butenweg, Christoph and Meyer, Udo and Fehling, Ekkehard}, title = {EU-Projekt INSYSME: Innovative Techniken f{\"u}r erdbebensichere Ausfachungsw{\"a}nde aus Ziegelmauerwerk in Stahlbetonrahmentragwerken}, series = {Mauerwerk : European journal of masonry}, volume = {18}, journal = {Mauerwerk : European journal of masonry}, number = {2}, publisher = {Ernst \& Sohn}, address = {Berlin}, issn = {1437-1022 (E-Journal); 1432-3427 (Print)}, doi = {10.1002/dama.201400612}, pages = {78 -- 81}, year = {2014}, abstract = {Am 1. Oktober 2013 ist das auf drei Jahre angelegte EU-Forschungsprojekt INSYSME - Innovative Systeme f{\"u}r erdbebentaugliche Ausfachungsw{\"a}nde aus Ziegelmauerwerk in Stahlbetonrahmentragwerken - gestartet. Unter der Koordination der Universit{\"a}t Padua beteiligen sich 16 Partner aus sechs europ{\"a}ischen L{\"a}ndern (Deutschland, Griechenland, Italien, Portugal, Rum{\"a}nien, T{\"u}rkei). Als deutsche Partner nehmen die Arbeitsgemeinschaft Mauerziegel aus Bonn, die Universit{\"a}t Kassel sowie das Ingenieurb{\"u}ro SDA-engineering GmbH aus Herzogenrath, teil. Ziel der deutschen Partner ist die Entwicklung von innovativen Ausfachungssystemen aus monolithischem w{\"a}rmed{\"a}mmenden Ziegelmauerwerk, mit denen nicht nur eine erh{\"o}hte Erdbebensicherheit, sondern auch die sichere Erf{\"u}llung der steigenden Anforderungen aus Windbeanspruchungen gew{\"a}hrleistet werden k{\"o}nnen. Die Forschungsergebnisse sollen vom Partner SDA-engineering GmbH in die bereits seit einigen Jahren verf{\"u}gbare Softwarel{\"o}sung MINEA [1] integriert werden. Weitere Informationen stehen auf den Websites des Projektes [2] zur Verf{\"u}gung. Im vorliegenden Beitrag werden nach einer kurzen thematischen Einf{\"u}hrung die Ergebnisse von Tastversuchen an senkrecht zur Ebene belasteten Ausfachungsw{\"a}nden aus Planziegelmauerwerk vorgestellt. Im Anschluss wird das geplante Arbeitsprogramm der deutschen Partner im Projekt INSYSME beschrieben.}, language = {de} } @inproceedings{ButenwegMeyerFehling2014, author = {Butenweg, Christoph and Meyer, Udo and Fehling, Ekkehard}, title = {INSYSME: first activities of the German partners}, series = {9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014}, booktitle = {9th International Masonry Conference 2014 in Guimaraes, Portugal, 2014}, year = {2014}, language = {en} } @inproceedings{ButenwegMeskourisMeisteretal.2011, author = {Butenweg, Christoph and Meskouris, Konstantin and Meister, Sylvia and Dreyer, Stephan and Schulte-Althoff, Christoph}, title = {Technisches Informationssystem f{\"u}r die Entwicklung textilbewehrten Betons}, series = {Textilbeton in Theorie und Praxis : Tagungsband zum 6. Kolloquium zu Textilbewehrten Tragwerken (CTRS6) in Berlin am 19. und 20.9.2011 / Technische Universit{\"a}t Dresden, Sonderforschungsbereich 528, herausgegeben von Manfred Curbach und Regine Ortlepp}, booktitle = {Textilbeton in Theorie und Praxis : Tagungsband zum 6. Kolloquium zu Textilbewehrten Tragwerken (CTRS6) in Berlin am 19. und 20.9.2011 / Technische Universit{\"a}t Dresden, Sonderforschungsbereich 528, herausgegeben von Manfred Curbach und Regine Ortlepp}, publisher = {Technische Universit{\"a}t}, address = {Dresden}, organization = {Kolloquium zu Textilbewehrten Tragwerken <6, 2011, Dresden>}, isbn = {978-3-86780-122-5}, pages = {257 -- 268}, year = {2011}, language = {de} } @inproceedings{ButenwegMarinkovićPaveseetal.2021, author = {Butenweg, Christoph and Marinković, Marko and Pavese, Alberto and Lanese, Igor and Hoffmeister, Benno and Pinkawa, Marius and Vulcu, Mihai-Cristian and Bursi, Oreste and Nardin, Chiara and Paolacci, Fabrizio and Quinci, Gianluca and Fragiadakis, Michalis and Weber, Felix and Huber, Peter and Renault, Philippe and G{\"u}ndel, Max and Dyke, Shirley and Ciucci, M. and Marino, A.}, title = {Seismic performance of multi-component systems in special risk industrial facilities}, series = {17. World Conference on Earthquake Engineering , Sendai , Japan , 17WCEE , 2021-09-27 - 2021-10-02}, booktitle = {17. World Conference on Earthquake Engineering , Sendai , Japan , 17WCEE , 2021-09-27 - 2021-10-02}, year = {2021}, abstract = {Past earthquakes demonstrated the high vulnerability of industrial facilities equipped with complex process technologies leading to serious damage of the process equipment and multiple and simultaneous release of hazardous substances in industrial facilities. Nevertheless, the design of industrial plants is inadequately described in recent codes and guidelines, as they do not consider the dynamic interaction between the structure and the installations and thus the effect of seismic response of the installations on the response of the structure and vice versa. The current code-based approach for the seismic design of industrial facilities is considered not enough for ensure proper safety conditions against exceptional event entailing loss of content and related consequences. Accordingly, SPIF project (Seismic Performance of Multi- Component Systems in Special Risk Industrial Facilities) was proposed within the framework of the European H2020 - SERA funding scheme (Seismology and Earthquake Engineering Research Infrastructure Alliance for Europe). The objective of the SPIF project is the investigation of the seismic behavior of a representative industrial structure equipped with complex process technology by means of shaking table tests. The test structure is a three-story moment resisting steel frame with vertical and horizontal vessels and cabinets, arranged on the three levels and connected by pipes. The dynamic behavior of the test structure and installations is investigated with and without base isolation. Furthermore, both firmly anchored and isolated components are taken into account to compare their dynamic behavior and interactions with each other. Artificial and synthetic ground motions are applied to study the seismic response at different PGA levels. After each test, dynamic identification measurements are carried out to characterize the system condition. The contribution presents the numerical simulations to calibrate the tests on the prototype, the experimental setup of the investigated structure and installations, selected measurement data and finally describes preliminary experimental results.}, language = {en} } @inproceedings{ButenwegMarinkovićKubalskietal.2017, author = {Butenweg, Christoph and Marinković, Marko and Kubalski, Thomas and Fehling, Ekkehard and Pfetzing, Thomas and Meyer, Udo}, title = {Innovative Ans{\"a}tze f{\"u}r die seismische Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk}, series = {Vortragsband der 15. D-A-CH-Tagung Erdbebeningenieurwesen und Baudynamik}, booktitle = {Vortragsband der 15. D-A-CH-Tagung Erdbebeningenieurwesen und Baudynamik}, editor = {Zabel, Volkmar and Beinersdorf, Silke}, publisher = {Deutsche Gesellschaft f{\"u}r Erdbebeningenieurwesen und Baudynamik (DGEB) e.V.}, address = {Weimar}, isbn = {978-3-930108-13-5}, pages = {130 -- 145}, year = {2017}, language = {de} } @article{ButenwegMarinkovićKubalskietal.2018, author = {Butenweg, Christoph and Marinković, Marko and Kubalski, Thomas and Fehling, Ekkehard and Pfetzing, Thomas and Meyer, Udo}, title = {Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 1)}, series = {Ziegelindustrie international : ZI = Brick and tile industry international}, journal = {Ziegelindustrie international : ZI = Brick and tile industry international}, number = {4}, editor = {Voss, Michael}, publisher = {Bauverlag BV GmbH}, address = {G{\"u}tersloh}, issn = {0341-0552}, pages = {30 -- 39}, year = {2018}, abstract = {Im Rahmen des europ{\"a}ischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragf{\"a}higkeit durch aufwendige und kostspielige zus{\"a}tzliche Bewehrungseinlagen zu erh{\"o}hen. Erste Ergebnisse des Systems IMES f{\"u}r Belastungen in und senkrecht zu der Wandebene werden vorgestellt.}, language = {de} } @article{ButenwegMarinkovićKubalskietal.2018, author = {Butenweg, Christoph and Marinković, Marko and Kubalski, Thomas and Fehling, Ekkehard and Pfetzing, Thomas and Meyer, Udo}, title = {Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 2)}, series = {Ziegelindustrie international : ZI = Brick and tile industry international}, journal = {Ziegelindustrie international : ZI = Brick and tile industry international}, number = {6}, editor = {Voss, Michael}, publisher = {Bauverlag BV GmbH}, address = {G{\"u}tersloh}, issn = {0341-0552}, pages = {24 -- 43}, year = {2018}, abstract = {Im Rahmen des europ{\"a}ischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragf{\"a}higkeit durch aufwendige und kostspielige zus{\"a}tzliche Bewehrungseinlagen zu erh{\"o}hen. Erste Ergebnisse des Systems IMES f{\"u}r Belastungen in und senkrecht zu der Wandebene werden vorgestellt.}, language = {de} } @article{ButenwegMarinkovićFehlingetal.2018, author = {Butenweg, Christoph and Marinković, Marko and Fehling, Ekkehard and Pfetzing, Thomas}, title = {Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk unter kombinierten seismischen Belastungen in und senkrecht zur Wandebene}, series = {Bauingenieur}, volume = {93}, journal = {Bauingenieur}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, isbn = {0005-6650}, pages = {2 -- 10}, year = {2018}, language = {de} } @article{ButenwegMarinkovicSalatic2019, author = {Butenweg, Christoph and Marinkovic, Marko and Salatic, Ratko}, title = {Experimental results of reinforced concrete frames with masonry infills under combined quasi-static in-plane and out-of-plane seismic loading}, series = {Bulletin of Earthquake Engineering}, volume = {17}, journal = {Bulletin of Earthquake Engineering}, publisher = {Springer}, address = {Berlin}, issn = {1573-1456}, doi = {10.1007/s10518-019-00602-7}, pages = {3397 -- 3422}, year = {2019}, language = {en} } @article{ButenwegMarinkovicPhlippetal.2022, author = {Butenweg, Christoph and Marinkovic, Marko and Phlipp, Michel and Lins, Robin and Renaut, Philipp}, title = {Isolierung und BIM-basiertes Bauwerksmonitoring des neuen Geb{\"a}udekomplexes f{\"u}r das BioSense-Institut in Novi Sad, Serbien}, series = {Bauingenieur}, volume = {97}, journal = {Bauingenieur}, number = {6}, editor = {Haghsheno, Shervin}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, issn = {1436-4867}, doi = {10.37544/0005-6650-2022-06-28}, pages = {S3 -- S5}, year = {2022}, abstract = {Im Norden von Serbien erfolgt in Novi Sad der Neubau eines modernen Forschungsgeb{\"a}udes f{\"u}r das BioSense-Institut mit finanzieller Unterst{\"u}tzung durch die Eu-rop{\"a}ische Union. Der Geb{\"a}udeteil mit Laboren wird zum Schutz und zur Sicherstellung des reibungslosen Betriebs der sensiblen und kapitalintensiven technischen Einbauten mit ei-ner Erdbebenisolierung mit integrierter K{\"o}rperschallisolation versehen. Zus{\"a}tzlich wird der entkoppelte Laborteil des For-schungsgeb{\"a}udes mit einem BIM-basierten Bauwerksmonito-ring versehen, um {\"A}nderungen des Geb{\"a}udezustands jederzeit abfragen und beurteilen zu k{\"o}nnen.}, language = {de} } @article{ButenwegMarinkovicKubalskietal.2016, author = {Butenweg, Christoph and Marinkovic, Marko and Kubalski, Thomas and Klinkel, Sven}, title = {Masonry infilled reinforced concrete frames under horizontal loading}, series = {Mauerwerk}, volume = {20}, journal = {Mauerwerk}, number = {4}, publisher = {Ernst \& Sohn}, address = {Berlin}, issn = {1437-1022}, doi = {10.1002/dama.201600703}, pages = {305 -- 312}, year = {2016}, abstract = {The behaviour of infilled reinforced concrete frames under horizontal load has been widely investigated, both experimentally and numerically. Since experimental tests represent large investments, numerical simulations offer an efficient approach for a more comprehensive analysis. When RC frames with masonry infill walls are subjected to horizontal loading, their behaviour is highly non-linear after a certain limit, which makes their analysis quite difficult. The non-linear behaviour results from the complex inelastic material properties of the concrete, infill wall and conditions at the wall-frame interface. In order to investigate this non-linear behaviour in detail, a finite element model using a micro modelling approach is developed, which is able to predict the complex non-linear behaviour resulting from the different materials and their interaction. Concrete and bricks are represented by a non-linear material model, while each reinforcement bar is represented as an individual part installed in the concrete part and behaving elasto-plastically. Each brick is modelled individually and connected taking into account the non-linearity of a brick mortar interface. The same approach is followed using two finite element software packages and the results are compared with the experimental results. The numerical models show a good agreement with the experiments in predicting the overall behaviour, but also very good matching for strength capacity and drift. The results emphasize the quality and the valuable contribution of the numerical models for use in parametric studies, which are needed for the derivation of design recommendations for infilled frame structures.}, language = {en} }