@inproceedings{ŠakićMilijašMarinkovićetal.2021,
  author    = {Šakić, Bogdan and Milijaš, Aleksa and Marinković, Marko and Butenweg, Christoph and Klinkel, Sven},
  title     = {Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load},
  series = {8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering},
  booktitle = {8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering},
  editor    = {Papadrakakis, Manolis and Fragiadakis, Michalis},
  publisher = {National Technical University of Athens},
  address   = {Athen},
  isbn      = {9786188507258},
  issn      = {2623-3347},
  doi       = {10.7712/120121.8527.18913},
  pages     = {808 -- 828},
  year      = {2021},
  abstract  = {Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic.},
  language  = {en}
}
@article{ŠakićMarinkovićButenwegetal.2023,
  author    = {Šakić, Bogdan and Marinković, Marko and Butenweg, Christoph and Klinkel, Sven},
  title     = {Influence of slab deflection on the out-of-plane capacity of unreinforced masonry partition walls},
  series = {Engineering Structures},
  volume    = {276},
  journal   = {Engineering Structures},
  editor    = {Yang, J.},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0141-0296},
  doi       = {10.1016/j.engstruct.2022.115342},
  year      = {2023},
  abstract  = {Severe damage of non-structural elements is noticed in previous earthquakes, causing high economic losses and posing a life threat for the people. Masonry partition walls are one of the most commonly used non-structural elements. Therefore, their behaviour under earthquake loading in out-of-plane (OOP) direction is investigated by several researches in the past years. However, none of the existing experimental campaigns or analytical approaches consider the influence of prior slab deflection on OOP response of partition walls. Moreover, none of the existing construction techniques for the connection of partition walls with surrounding reinforced concrete (RC) is investigated for the combined slab deflection and OOP loading. However, the inevitable time-dependent behaviour of RC slabs leads to high values of final slab deflections which can further influence boundary conditions of partition walls. Therefore, a comprehensive study on the influence of slab deflection on the OOP capacity of masonry partitions is conducted. In the first step, experimental tests are carried out. Results of experimental tests are further used for the calibration of the numerical model employed for a parametric study. Based on the results, behaviour under combined loading for different construction techniques is explained. The results show that slab deflection leads either to severe damage or to a high reduction of OOP capacity. Existing practical solutions do not account for these effects. In this contribution, recommendations to overcome the problems of combined slab deflection and OOP loading on masonry partition walls are given. Possible interaction of in-plane (IP) loading, with the combined slab deflection and OOP loading on partition walls, is not investigated in this study.},
  language  = {en}
}
@inproceedings{ZischankKernFrentzeletal.2000,
  author    = {Zischank, Wolfgang J. and Kern, Alexander and Frentzel, Ralf and Heidler, Fridolin and Seevers, M.},
  title     = {Assessment of the lightning transient coupling to control cables interconnecting structures in large industrial facilities and power plants},
  year      = {2000},
  abstract  = {Large industrial facilities and power plants often require a huge number fo information and control cables between the differnet structures. These I\&C-cables can be routed in reinforced concrete cable ducts or in isolated buried cable runs. KTA 2206 is the German lightning protection standard for nuclear power plants. During the last several years considerable effort has been made to revise this standard. Despite the well established principles and design guidelines for the construction of the lightning protection system, this standard puts special emphasis on the coupling of transient overvoltages to I\&C-cables.},
  language  = {en}
}
@inproceedings{ZischankHeidlerWiesingeretal.2004,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Wiesinger, J. and Stimper, K. and Kern, Alexander and Seevers, M.},
  title     = {Magnetic Fields and Induced Voltages inside LPZ 1 Measured at a 1:6 Scale Model Building},
  year      = {2004},
  abstract  = {Laborexperimente zu Blitzschutzzonen in Stahlbetongeb{\"a}uden anhand eines Modells im Maßstab 1:6},
  language  = {en}
}
@article{ZischankHeidlerWiesingeretal.2004,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Wiesinger, J. and Metwally, I. and Kern, Alexander and Seevers, M.},
  title     = {Laboratory simulation of direct lightning strokes to a modeled building : measurement of magnetic fields and included voltages},
  series = {Journal of electrostatics. 60 (2004), H. 2 - 4},
  journal   = {Journal of electrostatics. 60 (2004), H. 2 - 4},
  isbn      = {0304-3886},
  pages     = {223 -- 232},
  year      = {2004},
  language  = {en}
}
@inproceedings{ZischankHeidlerKernetal.2002,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Kern, Alexander and Metwally, I. A. and Wiesinger, J. and Seevers, M.},
  title     = {Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages},
  year      = {2002},
  abstract  = {In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between "floor" and "roof" in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived.},
  language  = {en}
}
@inproceedings{ZieglerSchuellerMottaghy2013,
  author    = {Ziegler, M. and Sch{\"u}ller, R. and Mottaghy, Darius},
  title     = {Numerical simulation of energy consumption of artificial ground freezing applications subject to water seepage},
  series = {Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013},
  booktitle = {Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013},
  pages     = {2985 -- 2988},
  year      = {2013},
  language  = {en}
}
@article{ZatkoDubeckyBohaceketal.2004,
  author    = {Zatko, B. and Dubeck{\´y}, F. and Bohacek, P. and Gombia, E. and Frigeri, P. and Mosca, R. and Franchi, S. and Huarn, J. and Nescas, V. and Sekacova, M. and F{\"o}rster, Arnold and Kordos, P.},
  title     = {On the spectrometric performance limit of radiation detectors based on semi-insulating GaAs},
  series = {Nuclear instruments and methods in physics research, Section A. 531 (2004), H. 1-2},
  journal   = {Nuclear instruments and methods in physics research, Section A. 531 (2004), H. 1-2},
  isbn      = {0168-9002},
  pages     = {111 -- 120},
  year      = {2004},
  language  = {en}
}
@inproceedings{ZahraPhaniSrujanCaminosetal.2022,
  author    = {Zahra, Mahdi and Phani Srujan, Merige and Caminos, Ricardo Alexander Chico and Schmitz, Pascal and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e} and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and Dersch, J{\"u}rgen},
  title     = {Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086268},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica.},
  language  = {en}
}
@book{Waehlisch2012,
  author    = {W{\"a}hlisch, Georg},
  title     = {Technisches Zeichnen : L{\"o}sungsvorschl{\"a}ge f{\"u}r das Selbststudium. (Berichte aus dem Maschinenbau)},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8440-1159-3},
  pages     = {[138] S. : zahlr. Ill., graph. Darst.},
  year      = {2012},
  language  = {de}
}
@book{Waehlisch2009,
  author    = {W{\"a}hlisch, Georg},
  title     = {Technisches Zeichnen : Vorlesung und {\"U}bungen},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8322-8044-4},
  pages     = {IV, 120, 80 S. : Ill., graph. Darst.},
  year      = {2009},
  language  = {de}
}
@inproceedings{WuttkeButenwegRosinetal.2019,
  author    = {Wuttke, Claudia and Butenweg, Christoph and Rosin, Julia and Kubalski, Thomas},
  title     = {Verbesserte seismische Nachweiskonzepte f{\"u}r Mauerwerksbauten in deutschen Erdbebengebieten},
  series = {Adam, Christoph (Hrsg.) ; Univ. Innsbruck: 16. D-A-CH Tagung Erdbebeningenieurwesen \& Baudynamik 2019 : 26. und 27. September 2019, Innsbruck},
  booktitle = {Adam, Christoph (Hrsg.) ; Univ. Innsbruck: 16. D-A-CH Tagung Erdbebeningenieurwesen \& Baudynamik 2019 : 26. und 27. September 2019, Innsbruck},
  address   = {Innsbruck},
  isbn      = {978-3-200-06454-6},
  pages     = {713 -- 722},
  year      = {2019},
  language  = {de}
}
@article{WettingfeldKernKraemeretal.2009,
  author    = {Wettingfeld, J{\"u}rgen and Kern, Alexander and Kr{\"a}mer, Heinz-Josef and Thorm{\"a}hlen, Reyno},
  title     = {International anerkannte Blitzschutznormen : Ausgewogener und sicherer Schutz},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  year      = {2009},
  abstract  = {Die Einleitung zur Norm DIN EN 62305-3 beschreibt klar und ein - deutig: Der vorliegende Teil der IEC 62305 behandelt den Schutz von baulichen Anlagen gegen materielle Sch{\"a}den und den Schutz von Personen gegen Verletzungen durch Ber{\"u}hrungs- und Schrittspannungen. Als das wesentlichste und effektivste Mittel zum Schutz von baulichen Anlagen gegen materielle Sch{\"a}den gilt das Blitz - schutzsystem (LPS).},
  subject      = {Blitzschutz},
  language  = {de}
}
@inproceedings{WetterKern2014,
  author    = {Wetter, Martin and Kern, Alexander},
  title     = {Number of lightning strikes to tall structures - comparison of calculations and measurements using a modern lightning monitoring system},
  series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  organization    = {International Conference on Lightning Protection <2014, Shanghai>},
  pages     = {1 -- 7},
  year      = {2014},
  language  = {en}
}
@inproceedings{WernerMansourRateikeetal.2011,
  author    = {Werner, Frederik and Mansour, Ahmed and Rateike, Franz-Matthias and Schusser, Sebastian and Wagner, Torsten and Yoshinobu, Tatsuo and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Kompakter Aufbau eines lichtadressierbaren potentiometrischen Sensors mit verfahrbarem Diodenlaser},
  series = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43},
  booktitle = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43},
  editor    = {Gerlach, Gerald},
  publisher = {TUDpress},
  address   = {Dresden},
  isbn      = {978-3-942710-53-4},
  pages     = {277 -- 280},
  year      = {2011},
  language  = {de}
}
@article{WernerKrumbeSchumacheretal.2011,
  author    = {Werner, Frederik and Krumbe, Christoph and Schumacher, Katharina and Groebel, Simone and Spelthahn, Heiko and Stellberg, Michael and Wagner, Torsten and Yoshinobu, Tatsuo and Selmer, Thorsten and Keusgen, Michael and Baumann, Marcus and Sch{\"o}ning, Michael Josef},
  title     = {Determination of the extracellular acidification of Escherichia coli by a light-addressable potentiometric sensor},
  series = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  journal   = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1862-6319},
  pages     = {1340 -- 1344},
  year      = {2011},
  language  = {en}
}
@incollection{WeberBomholtButenweg2022,
  author    = {Weber, Felix and Bomholt, Frederik and Butenweg, Christoph},
  title     = {Erdbeben- und Schwingungsschutz von Bauwerken},
  series = {2023 BetonKalender: Wasserundurchl{\"a}ssiger Beton, Br{\"u}ckenbau},
  booktitle = {2023 BetonKalender: Wasserundurchl{\"a}ssiger Beton, Br{\"u}ckenbau},
  editor    = {Bergmeister, Konrad and Fingerloos, Frank and W{\"o}rner, Johann-Dietrich},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  isbn      = {9783433611180},
  doi       = {10.1002/9783433611180.ch16},
  pages     = {779 -- 859},
  year      = {2022},
  abstract  = {Dieser Beitrag beschreibt die herk{\"o}mmlichen Maßnahmen wie die Kapazit{\"a}tsbemessung der Tragwerksstruktur, die Isolation des Bauwerks mittels Basisisolatoren, die D{\"a}mpfungserh{\"o}hung der Struktur mittels Inter-Story-D{\"a}mpfern und die Schwingungsreduktion mittels Schwingungstilgern gegen Einwirkungen durch Erdbeben, Wind, Verkehr und Personen auf die Bauwerke. Erg{\"a}nzend wird die erdbebengerechte Auslegung und Isolation von nichttragenden Bauteilen behandelt. F{\"u}r die betrachteten Systeme werden die Bewegungsdifferenzialgleichungen unter Ber{\"u}cksichtigung der wesentlichen Nichtlinearit{\"a}ten angegeben. Die vorgestellten Weiterentwicklungen in den Bereichen der Basisisolatoren, D{\"a}mpfern und Schwingungstilgern zeigen, dass das modellbasierte Design mittels Simulation ein sehr effektives, {\"o}konomisches und dank der heutigen Computerleistung auch zeiteffizientes Werkzeug darstellt.},
  language  = {de}
}
@article{WarerkarSchmitzGoettscheetal.2007,
  author    = {Warerkar, Shashikant and Schmitz, Stefan and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard},
  title     = {Wirtschaftlich und flexibel : Luft-Sand-W{\"a}rme{\"u}bertrager f{\"u}r die Energiespeicherung bei Temperaturen bis 800 °C},
  series = {Verfahrenstechnik. 41 (2007), H. 4},
  journal   = {Verfahrenstechnik. 41 (2007), H. 4},
  isbn      = {0175-5315},
  pages     = {72 -- 73},
  year      = {2007},
  language  = {de}
}
@article{WaltherGerthsenCariusetal.1993,
  author    = {Walther, T. and Gerthsen, D. and Carius, Reinhard and F{\"o}rster, Arnold},
  title     = {AlAs/GaAs Quantum well structures: Interface properties investigated by high-resolution transmission electron microscopy and photoluminescence spectroscopy / T. Walther ; D. Gerthsen ; R. Carius ; A. F{\"o}rster ...},
  series = {Microscopy of semiconducting materials 1993 : proceedings of the Royal Microscopical Society Conference held at Oxford University, 5 - 8 April 1993 / ed. by A. G. Cullis ... - (Conference series / Institute of Physics ; 134)},
  journal   = {Microscopy of semiconducting materials 1993 : proceedings of the Royal Microscopical Society Conference held at Oxford University, 5 - 8 April 1993 / ed. by A. G. Cullis ... - (Conference series / Institute of Physics ; 134)},
  publisher = {Institute of Physics},
  address   = {Bristol [u.a.]},
  isbn      = {0-7503-0290-9},
  pages     = {449 -- ff.},
  year      = {1993},
  language  = {en}
}
@article{WalterBorchert2002,
  author    = {Walter, G. and Borchert, J{\"o}rg},
  title     = {Der Einsatz von Realoptionen in der Elektrizit{\"a}tswirtschaft},
  series = {M \& A Review},
  journal   = {M \& A Review},
  number    = {4},
  issn      = {1616-0878},
  pages     = {198},
  year      = {2002},
  language  = {de}
}
@inproceedings{WagnerNohButenwegetal.2002,
  author    = {Wagner, R. and Noh, S.-Y. and Butenweg, Christoph and Meskouris, Konstantin},
  title     = {Seismic excited granular material silos},
  series = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ...},
  booktitle = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ...},
  publisher = {Balkema},
  address   = {Lisse},
  organization    = {European Conference on Structural Dynamics, EURODYN <5, 2002, M{\"u}nchen>},
  isbn      = {90-5809-511-8},
  pages     = {253 -- 258},
  year      = {2002},
  language  = {en}
}
@incollection{vondenDrieschSteuerDankertBergetal.2020,
  author    = {von den Driesch, Elena and Steuer-Dankert, Linda and Berg, Tobias and Leicht-Scholten, Carmen},
  title     = {Implementation of gender and diversity perspectives in transport development plans in germany},
  series = {Engendering cities: designing sustainable urban spaces for all},
  booktitle = {Engendering cities: designing sustainable urban spaces for all},
  publisher = {Routledge},
  address   = {London},
  isbn      = {978-1-351-20090-5},
  pages     = {90 -- 109},
  year      = {2020},
  abstract  = {As mobility should ensure the accessibility to and participation in society, transport planning has to deal with a variety of gender and diversity categories affecting users' mobility needs and patterns. Exemplified by an analysis of an instrument of transport development processes - German Transport Development Plans (TDPs) - we investigated to what extent diverse target groups and their mobility requirements are implemented in transport strategy papers. Research results illustrate a still-prevalent neglect of several relevant gender and diversity categories while prioritizing and focusing on eco-friendly topics. But how sustainable can transport be without facing the diversification of life circumstances?},
  language  = {en}
}
@article{VogtIwanowskiStrahserMarquartetal.2013,
  author    = {Vogt, Christian and Iwanowski-Strahser, Katha and Marquart, Gabriele and Arnold, Juliane and Mottaghy, Darius and Pechnig, Renate and Gnjezda, Daniel and Clauser, Christoph},
  title     = {Modeling contribution to risk assessment of thermal production power for geothermal reservoirs},
  series = {Renewable Energy},
  volume    = {53},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.11.026},
  pages     = {230 -- 241},
  year      = {2013},
  language  = {en}
}
@article{VogtMottaghyWolfetal.2010,
  author    = {Vogt, C. and Mottaghy, Darius and Wolf, A. and Rath, V. and Pechnig, R. and Clauser, C.},
  title     = {Reducing temperature uncertainties by stochastic geothermal reservoir modelling},
  series = {Geophysical Journal International},
  volume    = {181},
  journal   = {Geophysical Journal International},
  number    = {1},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1365-246X},
  doi       = {10.1111/j.1365-246X.2009.04498.x},
  pages     = {321 -- 333},
  year      = {2010},
  abstract  = {Quantifying and minimizing uncertainty is vital for simulating technically and economically successful geothermal reservoirs. To this end, we apply a stochastic modelling sequence, a Monte Carlo study, based on (i) creating an ensemble of possible realizations of a reservoir model, (ii) forward simulation of fluid flow and heat transport, and (iii) constraining post-processing using observed state variables. To generate the ensemble, we use the stochastic algorithm of Sequential Gaussian Simulation and test its potential fitting rock properties, such as thermal conductivity and permeability, of a synthetic reference model and—performing a corresponding forward simulation—state variables such as temperature. The ensemble yields probability distributions of rock properties and state variables at any location inside the reservoir. In addition, we perform a constraining post-processing in order to minimize the uncertainty of the obtained distributions by conditioning the ensemble to observed state variables, in this case temperature. This constraining post-processing works particularly well on systems dominated by fluid flow. The stochastic modelling sequence is applied to a large, steady-state 3-D heat flow model of a reservoir in The Hague, Netherlands. The spatial thermal conductivity distribution is simulated stochastically based on available logging data. Errors of bottom-hole temperatures provide thresholds for the constraining technique performed afterwards. This reduce the temperature uncertainty for the proposed target location significantly from 25 to 12 K (full distribution width) in a depth of 2300 m. Assuming a Gaussian shape of the temperature distribution, the standard deviation is 1.8 K. To allow a more comprehensive approach to quantify uncertainty, we also implement the stochastic simulation of boundary conditions and demonstrate this for the basal specific heat flow in the reservoir of The Hague. As expected, this results in a larger distribution width and hence, a larger, but more realistic uncertainty estimate. However, applying the constraining post-processing the uncertainty is again reduced to the level of the post-processing without stochastic boundary simulation. Thus, constraining post-processing is a suitable tool for reducing uncertainty estimates by observed state variables.},
  language  = {en}
}
@article{VogtMottaghyRathetal.2014,
  author    = {Vogt, C. and Mottaghy, Darius and Rath, V. and Marquart, G. and Dijkshoorn, L. and Wolf, A. and Clauser, C.},
  title     = {Vertical variation in heat flow on the Kola Peninsula: palaeoclimate or fluid flow?},
  series = {Geophysical Journal International},
  volume    = {199},
  journal   = {Geophysical Journal International},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1365-246X},
  doi       = {10.1093/gji/ggu282},
  pages     = {829 -- 843},
  year      = {2014},
  abstract  = {Following earlier studies, we present forward and inverse simulations of heat and fluid transport of the upper crust using a local 3-D model of the Kola area. We provide best estimates for palaeotemperatures and permeabilities, their errors and their dependencies. Our results allow discriminating between the two mentioned processes to a certain extent, partly resolving the non-uniqueness of the problem. We find clear indications for a significant contribution of advective heat transport, which, in turn, imply only slightly lower ground surface temperatures during the last glacial maximum relative to the present value. These findings are consistent with the general background knowledge of (i) the fracture zones and the corresponding fluid movements in the bedrock and (ii) the glacial history of the Kola area.},
  language  = {en}
}
@article{VitusevichFoersterReetzetal.2000,
  author    = {Vitusevich, S. A. and F{\"o}rster, Arnold and Reetz, W. and L{\"u}th, H. and Belyaev, A. E. and Danylyuk, S. V.},
  title     = {Spectral Responsivity of single-quantum-well photodetectors},
  series = {Applied Physics Letters. 77 (2000), H. 1},
  journal   = {Applied Physics Letters. 77 (2000), H. 1},
  isbn      = {1077-3118},
  pages     = {16 -- 18},
  year      = {2000},
  language  = {en}
}
@article{VitusevichFoersterReetzetal.2000,
  author    = {Vitusevich, S. A. and F{\"o}rster, Arnold and Reetz, W. and L{\"u}th, H. and Belyaev, A. E. and Danylyuk, S. V.},
  title     = {Fine structure of photoresponse spectra in a double-barrier resonant tunnelling diode},
  series = {Nanotechnology. 11 (2000), H. 4},
  journal   = {Nanotechnology. 11 (2000), H. 4},
  isbn      = {1361-6528},
  pages     = {305 -- 308},
  year      = {2000},
  language  = {en}
}
@article{VitusevichFoersterLuethetal.2001,
  author    = {Vitusevich, S. A. and F{\"o}rster, Arnold and L{\"u}th, H. and Belyaev, A. E. and Danylyuk, S. V. and Konakova, R. V. and Sheka, D. I.},
  title     = {Resonant spectroscopy of electric-field-induced superlattices},
  series = {Journal of Applied Physics. 90 (2001), H. 6},
  journal   = {Journal of Applied Physics. 90 (2001), H. 6},
  isbn      = {1089-7550},
  doi       = {10.1063/1.1392956},
  pages     = {2857 -- 2861},
  year      = {2001},
  language  = {en}
}
@article{VitusevichFoersterIndlekoferetal.2000,
  author    = {Vitusevich, S. A. and F{\"o}rster, Arnold and Indlekofer, K.-M. and L{\"u}th, H. and Belyaev, A. E. and Glavin, B. A. and Konakova, R. V.},
  title     = {Tunneling Through X-Valley-Related Impurity States in GaAs/AlAs Resonant-Tunneling Diodes},
  series = {Physical Review . B. 61 (2000), H. 16},
  journal   = {Physical Review . B. 61 (2000), H. 16},
  isbn      = {1550-235X},
  pages     = {10898 -- 10904},
  year      = {2000},
  language  = {en}
}
@article{VerschitzButenweg2014,
  author    = {Verschitz, Daniel and Butenweg, Christoph},
  title     = {Standsicherheitsnachweis von Beh{\"a}ltern f{\"u}r Kleinkl{\"a}ranlagen},
  series = {ACWA aktuell},
  journal   = {ACWA aktuell},
  number    = {12 - 9/2014},
  publisher = {RWTH Aachen},
  address   = {Aachen},
  pages     = {10},
  year      = {2014},
  abstract  = {Die PIA GmbH pr{\"u}ft seit fast 8 Jahren die Standsicherheit von Beh{\"a}ltern f{\"u}r Kleinkl{\"a}ranlagen. Diese bestehen in der Regel aus Kunststoff oder Beton und m{\"u}ssen {\"u}ber ihre gesamte Lebensdauer den Beanspruchungen aus Handhabung, Einbau und Betrieb standhalten. Die Standsicherheit kann nach EN 12566 wahlweise durch einen rechnerischen Nachweis oder durch einen praktischen Nachweis wie die Bruchlastpr{\"u}fung oder die Pr{\"u}fung in der Grube erfolgen.},
  language  = {de}
}
@article{VelrajSeenirajHafneretal.1997,
  author    = {Velraj, R. and Seeniraj, R. V. and Hafner, B. and Faber, Christian and Schwarzer, Klemens},
  title     = {Experimental analysis and numerical modelling of inward solidification on a finned vertical tube for a latent heat storage unit},
  series = {Solar energy. 60 (1997), H. 5},
  journal   = {Solar energy. 60 (1997), H. 5},
  isbn      = {0038-092X},
  pages     = {281 -- 290},
  year      = {1997},
  language  = {en}
}
@article{VargaDavinsonGloriusetal.2020,
  author    = {Varga, Laszlo and Davinson, Thomas and Glorius, Jan and Jurado, Beatrix and Langer, Christoph and Lederer-Woods, Claudia and Litvinov, Yuri A. and Reifarth, Rene and Slavkovska, Zuzana and St{\"o}hlker, Thomas and Woods, Phil J. and Xing, Yuan Ming},
  title     = {Towards background-free studies of capture reaction in a heavy-ion storage ring},
  series = {Journal of Physics: Conference Series},
  volume    = {1668},
  journal   = {Journal of Physics: Conference Series},
  number    = {Art 012046},
  publisher = {IOP},
  address   = {Bristol},
  year      = {2020},
  abstract  = {Stored and cooled, highly-charged ions offer unprecedented capabilities for precision studies in the realm of atomic, nuclear structure and astrophysics[1]. After the successful investigation of the 96Ru(p,7)97Rh reaction cross section in 2009[2], the first measurement of the 124Xe(p,7)125Cs reaction cross section has been performed with decelerated, fully-ionized 124Xe ions in 2016 at the Experimental Storage Ring (ESR) of GSI[3]. Using a Double Sided Silicon Strip Detector, introduced directly into the ultra-high vacuum environment of a storage ring, the 125Cs proton-capture products have been successfully detected. The cross section has been measured at 5 different energies between 5.5AMeV and 8AMeV, on the high energy tail of the Gamow-window for hot, explosive scenarios such as supernovae and X-ray binaries. The elastic scattering on the H2 gas jet target is the major source of background to count the (p,7) events. Monte Carlo simulations show that an additional slit system in the ESR in combination with the energy information of the Si detector will enable background free measurements of the proton-capture products. The corresponding hardware is being prepared and will increase the sensitivity of the method tremendously.},
  language  = {en}
}
@article{UngermannsAheCariusetal.1997,
  author    = {Ungermanns, C. and Ahe, M. v. d. and Carius, Reinhard and F{\"o}rster, Arnold},
  title     = {Optimization of III/V binary growth with RHEED in MOMBE / C. Ungermanns ; M. v. d. Ahe ; R. Carius ; A. F{\"o}rster ...},
  series = {Fresenius' Journal of Analytical Chemistry. 358 (1997), H. 1-2},
  journal   = {Fresenius' Journal of Analytical Chemistry. 358 (1997), H. 1-2},
  isbn      = {0937-0633},
  pages     = {101 -- 104},
  year      = {1997},
  language  = {en}
}
@inproceedings{TomićPennaDeJongetal.2020,
  author    = {Tomić, Igor and Penna, Andrea and DeJong, Matthew and Butenweg, Christoph and Correia, Ant{\´o}nio A. and Candeias, Paulo X. and Senaldi, Ilaria and Guerrini, Gabriele and Malomo, Daniele and Beyer, Katrin},
  title     = {Seismic testing of adjacent interacting masonry structures},
  series = {12th International Conference on Structural Analysis of Historical Constructions (SAHC 2020)},
  booktitle = {12th International Conference on Structural Analysis of Historical Constructions (SAHC 2020)},
  doi       = {10.23967/sahc.2021.234},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {In many historical centres in Europe, stone masonry buildings are part of building aggregates, which developed when the layout of the city or village was densified. In these aggregates, adjacent buildings share structural walls to support floors and roofs. Meanwhile, the masonry walls of the fa{\c{c}}ades of adjacent buildings are often connected by dry joints since adjacent buildings were constructed at different times. Observations after for example the recent Central Italy earthquakes showed that the dry joints between the building units were often the first elements to be damaged. As a result, the joints opened up leading to pounding between the building units and a complicated interaction at floor and roof beam supports. The analysis of such building aggregates is very challenging and modelling guidelines do not exist. Advances in the development of analysis methods have been impeded by the lack of experimental data on the seismic response of such aggregates. The objective of the project AIMS (Seismic Testing of Adjacent Interacting Masonry Structures), included in the H2020 project SERA, is to provide such experimental data by testing an aggregate of two buildings under two horizontal components of dynamic excitation. The test unit is built at half-scale, with a two-storey building and a one-storey building. The buildings share one common wall while the fa{\c{c}}ade walls are connected by dry joints. The floors are at different heights leading to a complex dynamic response of this smallest possible building aggregate. The shake table test is conducted at the LNEC seismic testing facility. The testing sequence comprises four levels of shaking: 25\%, 50\%, 75\% and 100\% of nominal shaking table capacity. Extensive instrumentation, including accelerometers, displacement transducers and optical measurement systems, provides detailed information on the building aggregate response. Special attention is paid to the interface opening, the globa},
  language  = {en}
}
@inproceedings{TomicPennaDeJongetal.2020,
  author    = {Tomic, Igor and Penna, Andrea and DeJong, Matthew and Butenweg, Christoph and Senaldi, Ilaria and Guerrini, Gabriele and Malomo, Daniele and Beyer, Katrin},
  title     = {Blind predictions of shake table testing of aggregate masonry buildings},
  series = {17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.},
  booktitle = {17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.},
  year      = {2020},
  abstract  = {In many historical centers in Europe, stone masonry is part of building aggregates, which developed when the layout of the city or village was densified. The analysis of such building aggregates is very challenging and modelling guidelines missing. Advances in the development of analysis methods have been impeded by the lack of experimental data on the seismic response of such aggregates. The SERA project AIMS (Seismic Testing of Adjacent Interacting Masonry Structures) provides such experimental data by testing an aggregate of two buildings under two horizontal components of dynamic excitation. With the aim to advance the modelling of unreinforced masonry aggregates, a blind prediction competition is organized before the experimental campaign. Each group has been provided a complete set of construction drawings, material properties, testing sequence and the list of measurements to be reported. The applied modelling approaches span from equivalent frame models to Finite Element models using shell elements and discrete element models with solid elements. This paper compares the first entries, regarding the modelling approaches, results in terms of base shear, roof displacements, interface openings, and the failure modes.},
  language  = {en}
}
@article{TillmannFoerster2000,
  author    = {Tillmann, K. and F{\"o}rster, Arnold},
  title     = {Critical dimensions for the formation of interfacial misfit dislocations of In0.6Ga0.4As islands on GaAs(001)},
  series = {Thin Solid Films. 368 (2000), H. 1},
  journal   = {Thin Solid Films. 368 (2000), H. 1},
  isbn      = {0040-6090},
  pages     = {93 -- 104},
  year      = {2000},
  language  = {en}
}
@book{ThielemannStaudtTobergetal.1992,
  author    = {Thielemann, Frank and Staudt, Erich and Toberg, M. and Linn{\´e}, H.},
  title     = {Kooperationshandbuch : ein Leitfaden f{\"u}r die Unternehmenspraxis / Staudt, E.; Toberg, M.; Linn{\´e}, H.; Bock, J.; Thielemann, F.},
  publisher = {VDI-Verl. [u.a.]},
  address   = {D{\"u}sseldorf},
  isbn      = {3-18-401217-4},
  year      = {1992},
  language  = {de}
}
@book{ThielemannStaudtSchaffner1996,
  author    = {Thielemann, Frank and Staudt, Erich and Schaffner, Michael},
  title     = {Strategische Kooperationen - ein Weg f{\"u}r die Druckindustrie 2000 ins Medienzeitalter? Ergebnisse einer empirischen Untersuchung zu kooperativen Gesch{\"a}ftsbeziehungen der Druckindustrie / Erich Staudt ; Frank Thielemann ; Michael Schaffner},
  publisher = {Inst. f{\"u}r Angewandte Innovationsforschung e.V.},
  address   = {Bochum},
  pages     = {50 S. : graph. Darst.},
  year      = {1996},
  language  = {de}
}
@book{ThielemannStaudtKriegesmannetal.1996,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd and Behrendt, S.},
  title     = {Kooperationsleitfaden : Planungshilfen und Checklisten zum Management zwischenbetrieblicher Kooperation / Staudt, E.; Kriegesmann, B.; Thielemann, F.; Behrendt, S.},
  publisher = {Raabe},
  address   = {Stuttgart [u.a.]},
  isbn      = {3-88649-188-9},
  pages     = {II, 86 S. : graph. Darst.},
  year      = {1996},
  language  = {de}
}
@book{ThielemannStaudtKriegesmannetal.1994,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd and Behrendt, S.},
  title     = {Kooperation als Erfolgsfaktor ostdeutscher Unternehmen : Ergebnisse einer empirischen Untersuchung zur Kooperationslandschaft in Ostdeutschland / Staudt, E.; Kriegesmann, B.; Thielemann, F.; Behrendt, S.; Chalupsky, J.},
  publisher = {Inst. f{\"u}r Angewandte Innovationsforschung e.V.},
  address   = {Bochum},
  pages     = {47 S. : graph. Darst.},
  year      = {1994},
  language  = {de}
}
@article{ThielemannStaudtKriegesmann1995,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd},
  title     = {Kooperation als Erfolgsfak­tor ostdeutscher Unternehmen. Ergebnisse einer empirischen Untersu­chung zur Ko­operationslandschaft in Ost­deutschland. Staudt, E.; Kriegesmann, B.; Thielemann, F.},
  series = {Zeitschrift f{\"u}r Betriebswirtschaft ZfB. 65 (1995), H. 11},
  journal   = {Zeitschrift f{\"u}r Betriebswirtschaft ZfB. 65 (1995), H. 11},
  isbn      = {0044-2372},
  pages     = {1209 -- 1230},
  year      = {1995},
  language  = {de}
}
@book{ThielemannStaudtKriegesmann1994,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd},
  title     = {Joint-ventures. Staudt, Erich; Kriegesmann, Bernd; Thielemann, Frank},
  publisher = {Inst. f{\"u}r Angewandte Innovationsforschung e.V.},
  address   = {Bochum},
  pages     = {29 S. : graph. Darst.},
  year      = {1994},
  language  = {en}
}
@book{ThielemannStaudtKriegesmann1995,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd},
  title     = {Qualifikationsbeschaffung im Transformationsprozeß : Ergebnisse einer empirischen Untersuchung in der Druckindustrie / Staudt, Erich; Kriegesmann, Bernd ; Thielemann, Frank},
  publisher = {Inst. f{\"u}r Angewandte Innovationsforschung e.V.},
  address   = {Bochum},
  pages     = {36 S. : graph. Darst.},
  year      = {1995},
  language  = {de}
}
@article{ThielemannStaudtKriegesmann1997,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd},
  title     = {Neuformierung von Wertsch{\"o}pfungsketten: Das Beispiel Druckindustrie . Staudt, Erich; Kriegesmann, Bernd; Thielemann, Frank},
  series = {Zeitschrift F{\"u}hrung und Organisation. 96 (1997), H. 2},
  journal   = {Zeitschrift F{\"u}hrung und Organisation. 96 (1997), H. 2},
  isbn      = {0044-3212},
  pages     = {75 -- 80},
  year      = {1997},
  language  = {de}
}
@article{ThielemannStaudtKriegesmann1998,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd},
  title     = {Kooperationsverhalten in der Druckindustrie - zwischen Bestandssicherung und Offensive. Staudt, Erich; Kriegesmann, Bernd; Thielemann, Frank},
  series = {Die Betriebswirtschaft. 58 (1998), H. 6},
  journal   = {Die Betriebswirtschaft. 58 (1998), H. 6},
  isbn      = {0342-7064},
  pages     = {803 -- 815},
  year      = {1998},
  language  = {de}
}
@article{ThielemannStaudt1997,
  author    = {Thielemann, Frank and Staudt, Erich},
  title     = {Kompetenz zur Innovation: Vom Druckbetrieb zum Multimedia-Dienstleister . Staudt, E.; Thielemann, F.},
  series = {News Letter (der Gesellschaft f{\"u}r Wirtschaftsf{\"o}rde­rung Duisburg) (1997)},
  journal   = {News Letter (der Gesellschaft f{\"u}r Wirtschaftsf{\"o}rde­rung Duisburg) (1997)},
  pages     = {3 -- 3},
  year      = {1997},
  language  = {de}
}
@article{ThielemannStaudt1997,
  author    = {Thielemann, Frank and Staudt, Erich},
  title     = {Reicht die Kompetenz zur Innovation? Staudt, E.; Thielemann, F.},
  series = {OP DruckMagazin. 39 (1997), H. 10},
  journal   = {OP DruckMagazin. 39 (1997), H. 10},
  isbn      = {0030-0594},
  pages     = {30 -- 32},
  year      = {1997},
  language  = {de}
}
@book{ThielemannStaudt1996,
  author    = {Thielemann, Frank and Staudt, Erich},
  title     = {Von der Druckindustrie zum Multimedia-Dienstleister : Kompetenz durch Innovation / Erich Staudt ; Thielemann, Frank},
  publisher = {Inst. f{\"u}r Angewandte Innovationsforschung e.V.},
  address   = {Bochum},
  pages     = {40 S.:graph. Darst.},
  year      = {1996},
  language  = {de}
}
@book{ThielemannStaudt1998,
  author    = {Thielemann, Frank and Staudt, Erich},
  title     = {Innovation durch strategische Allianzen : ein Wegweiser f{\"u}r die Druck- und Medienbranche . Staudt, Erich; Thielemann, Frank},
  publisher = {IAI, Inst. f{\"u}r Angewandte Innovationsforschung},
  address   = {Bochum},
  isbn      = {3-928854-14-3},
  pages     = {96 Bl.: graph. Darst.},
  year      = {1998},
  language  = {de}
}
@article{ThielemannSchaffner1993,
  author    = {Thielemann, Frank and Schaffner, M.},
  title     = {Innovationswiderst{\"a}nde bei der Einf{\"u}hrung neuer Tech­nologien. Schaffner, M.; Thielemann, F.},
  series = {Deutscher Drucker. 1992/93 (1993), H. 42},
  journal   = {Deutscher Drucker. 1992/93 (1993), H. 42},
  isbn      = {0012-1096},
  pages     = {g15 -- ff},
  year      = {1993},
  language  = {de}
}
@article{ThielemannSchaffner1993,
  author    = {Thielemann, Frank and Schaffner, M.},
  title     = {Wie beurteilen die F{\"u}hrungskr{\"a}fte der Branche den derzeitigen und zuk{\"u}nftigen Innovationsdruck? Expertenmeinung zum Thema Innovationen in der Druckindustrie: M. Schaffner, F. Thielemann},
  series = {Management im innovatorischen Wandel : Arbeit und Technik in der Druckindustrie / Heinz-Reiner Treichel ; Kurt-Georg Ciesinger},
  journal   = {Management im innovatorischen Wandel : Arbeit und Technik in der Druckindustrie / Heinz-Reiner Treichel ; Kurt-Georg Ciesinger},
  publisher = {Polygraph-Verl.},
  address   = {Frankfurt am Main},
  isbn      = {3-87641-262-5},
  pages     = {21 -- 26},
  year      = {1993},
  language  = {de}
}
@article{ThielemannSchaffner1996,
  author    = {Thielemann, Frank and Schaffner, M.},
  title     = {Gemeinsam sind wir stark . Schaffner, M.; Thielemann, F.},
  series = {Print \& Produktion. 9 (1996), H. 10},
  journal   = {Print \& Produktion. 9 (1996), H. 10},
  isbn      = {0944-7482},
  pages     = {28 -- f.},
  year      = {1996},
  language  = {de}
}
@article{ThielemannSchaffner1993,
  author    = {Thielemann, Frank and Schaffner, M.},
  title     = {Innovationswiderst{\"a}nde bei der Einf{\"u}hrung neuer Tech­nologien. Schaffner, M.; Thielemann, F.},
  series = {Deutscher Drucker. 1992/93 (1993), H. 38},
  journal   = {Deutscher Drucker. 1992/93 (1993), H. 38},
  isbn      = {0012-1096},
  pages     = {g12 -- ff},
  year      = {1993},
  language  = {de}
}
@article{ThielemannSchaffner1996,
  author    = {Thielemann, Frank and Schaffner, M.},
  title     = {Vom Einzelk{\"a}mpfertum zum kooperativen Kundenservice},
  series = {Polygraph. 49 (1996), H. 23-24},
  journal   = {Polygraph. 49 (1996), H. 23-24},
  isbn      = {0032-3842},
  pages     = {40 -- 42},
  year      = {1996},
  language  = {de}
}
@article{ThielemannLuedtke2001,
  author    = {Thielemann, Frank and L{\"u}dtke, C.},
  title     = {Balanced Scorecard - Von der Vision zur Strategie},
  series = {Wirtschafts-Nachrichten. 46 (2001), H. 9},
  journal   = {Wirtschafts-Nachrichten. 46 (2001), H. 9},
  isbn      = {1436-5588},
  pages     = {10 -- f.},
  year      = {2001},
  language  = {de}
}
@article{ThielemannLuedtke2000,
  author    = {Thielemann, Frank and L{\"u}dtke, C.},
  title     = {Einfluß des KonTraG im Unternehmensbereich},
  series = {Wirtschafts-Nachrichten. 45 (2000), H. 8},
  journal   = {Wirtschafts-Nachrichten. 45 (2000), H. 8},
  isbn      = {1436-5588},
  pages     = {10 -- f.},
  year      = {2000},
  language  = {de}
}
@article{ThielemannLuedtke2000,
  author    = {Thielemann, Frank and L{\"u}dtke, C.},
  title     = {Risikomanagement - Aufbau eines Fr{\"u}hwarnsystems},
  series = {Wirtschafts-Nachrichten. 45 (2000), H. 12},
  journal   = {Wirtschafts-Nachrichten. 45 (2000), H. 12},
  isbn      = {1436-5588},
  pages     = {14 -- ff},
  year      = {2000},
  language  = {de}
}
@article{ThielemannLuedtke1999,
  author    = {Thielemann, Frank and L{\"u}dtke, C.},
  title     = {Wie sich Logistikunternehmen ihren Platz sichern k{\"o}nnen},
  series = {Deutsche Verkehrs-Zeitung (DVZ) (1999)},
  journal   = {Deutsche Verkehrs-Zeitung (DVZ) (1999)},
  isbn      = {0342-166X},
  pages     = {42 -- 42},
  year      = {1999},
  language  = {de}
}
@article{ThielemannLang2000,
  author    = {Thielemann, Frank and Lang, Franz Peter},
  title     = {Wissensmanagement und neue Informationstechnologie . Lang, Franz Peter; Thielemann, Frank},
  series = {Ver{\"a}nderungsmanagement in der Sozialwirtschaft / Bernd Maelicke (Hrsg.)},
  journal   = {Ver{\"a}nderungsmanagement in der Sozialwirtschaft / Bernd Maelicke (Hrsg.)},
  publisher = {Nomos-Verl.-Ges.},
  address   = {Baden-Baden},
  isbn      = {3-7890-6738-5},
  pages     = {132 -- 172},
  year      = {2000},
  language  = {de}
}
@article{ThielemannKriegesmannSchaffner1995,
  author    = {Thielemann, Frank and Kriegesmann, Bernd and Schaffner, M.},
  title     = {Mit vereinten Kr{\"a}ften die Wettbewerbsf{\"a}higkeit steigern - Kooperation als Antwort auf den In­novationsdruck . Kriegesmann, B.; Thielemann, F.; Schaffner, M.},
  series = {Der Druckspiegel. 50 (1995), H. 10},
  journal   = {Der Druckspiegel. 50 (1995), H. 10},
  isbn      = {0012-6500},
  pages     = {931 -- 935},
  year      = {1995},
  language  = {de}
}
@book{ThielemannKeller2004,
  author    = {Thielemann, Frank and Keller, Gernot},
  title     = {Bilanzen international : ein komprimierter {\"U}berblick nach HGB und IAS/IFRS. 4., v{\"o}llig {\"u}berarb. und erw. Aufl.},
  publisher = {MA, Akad.-Verl.- und Druck-Ges.},
  address   = {Essen},
  isbn      = {3-89275-026-2},
  pages     = {XVI, 315 S. : Ill.},
  year      = {2004},
  language  = {de}
}
@book{ThielemannCiesingerSiebecke1999,
  author    = {Thielemann, Frank and Ciesinger, Kurt-Georg and Siebecke, Dagmar},
  title     = {Innovationsintegral Mittelstand : Kompetenzentwicklung in Medienkooperationen. Ciesinger, Kurt-Georg ; Siebecke, Dagmar ; Thielemann, Frank},
  publisher = {Lit},
  address   = {M{\"u}nster},
  isbn      = {3-8258-4217-7},
  pages     = {183 S.: graph. Darst.},
  year      = {1999},
  language  = {de}
}
@article{ThielemannChalupsky1994,
  author    = {Thielemann, Frank and Chalupsky, J.},
  title     = {Der Markt verlangt nach Kooperationen},
  series = {Leipziger Wirtschaft. 5 (1994), H. 6},
  journal   = {Leipziger Wirtschaft. 5 (1994), H. 6},
  pages     = {14 -- 18},
  year      = {1994},
  language  = {de}
}
@book{ThielemannBock1992,
  author    = {Thielemann, Frank and Bock, J{\"u}rgen},
  title     = {Ost-West-Joint-ventures : Erfahrungen beim Aufbau und Management deutsch-russischer Gemeinschaftsunternehmen / Bock, J{\"u}rgen; Thielemann, Frank},
  publisher = {Inst. f{\"u}r Angewandte Innovationsforschung e.V.},
  address   = {Bochum},
  pages     = {47 S.},
  year      = {1992},
  language  = {de}
}
@article{ThielemannBock1993,
  author    = {Thielemann, Frank and Bock, J{\"u}rgen},
  title     = {Aufbau und Management deutsch-russischer Joint-ventures. Bock J{\"u}rgen; Thielemann, Frank},
  series = {Mit Innovation vom Plan zum Markt},
  journal   = {Mit Innovation vom Plan zum Markt},
  address   = {Bochum},
  pages     = {111 -- 135},
  year      = {1993},
  language  = {de}
}
@article{ThielemannBock1994,
  author    = {Thielemann, Frank and Bock, J{\"u}rgen},
  title     = {Organization and management of German-Russian joint ventures. Bock, J{\"u}rgen; Thielemann, Frank},
  series = {International journal of technology management. 9 (1994), H. 8},
  journal   = {International journal of technology management. 9 (1994), H. 8},
  isbn      = {0267-5730},
  pages     = {864 -- 879},
  year      = {1994},
  language  = {en}
}
@book{ThielemannBachem2002,
  author    = {Thielemann, Frank and Bachem, Claus},
  title     = {{\"U}berlegungen zur Evaluation von Technologief{\"o}rderprogrammen},
  publisher = {nst. f{\"u}r Wirtschaftswiss.},
  address   = {Braunschweig},
  isbn      = {3-933628-42-3},
  pages     = {48 S : graph. Darst.},
  year      = {2002},
  language  = {de}
}
@article{Thielemann1997,
  author    = {Thielemann, Frank},
  title     = {Chancen durch Online-Dienste?},
  series = {OP DruckMagazin. 39 (1997), H. 1-2},
  journal   = {OP DruckMagazin. 39 (1997), H. 1-2},
  isbn      = {0030-0594},
  pages     = {26 -- f.},
  year      = {1997},
  language  = {de}
}
@article{Thielemann2000,
  author    = {Thielemann, Frank},
  title     = {Das Management von Innovationen aus betriebswirtschaftlicher Sicht},
  series = {Humanit{\"a}t - Wandel - Utopie / Bernd Rebe (Hrsg.). Mit Beitr. von Ute Daniel},
  journal   = {Humanit{\"a}t - Wandel - Utopie / Bernd Rebe (Hrsg.). Mit Beitr. von Ute Daniel},
  publisher = {Olms},
  address   = {Hildesheim},
  pages     = {33 -- 64},
  year      = {2000},
  language  = {de}
}
@book{Thielemann1996,
  author    = {Thielemann, Frank},
  title     = {Die Gestaltung von Kooperationen zwischen kleinen und mittleren Unternehmen},
  address   = {Bochum},
  pages     = {285, II S. : graph. Darst.},
  year      = {1996},
  language  = {de}
}
@book{Thielemann2000,
  author    = {Thielemann, Frank},
  title     = {Kompetenzentwicklung im Mittelstand - das Beispiel Kompetenz-Entwicklungs-Center / hrsg. von Frank Thielemann},
  publisher = {MA, Akademie-Verl.- und Druck-Ges.},
  address   = {Essen},
  isbn      = {3-89275-031-9},
  pages     = {302 S. : graph. Darst.},
  year      = {2000},
  language  = {de}
}
@book{Thielemann2000,
  author    = {Thielemann, Frank},
  title     = {Bilanzen - ein komprimierter {\"U}berblick : Intensivkurs zum betrieblichen Rechnungswesen. 2., {\"u}berarb. Aufl.},
  publisher = {MA, Akademie-Verl.- und Druck-Ges.},
  address   = {Essen},
  isbn      = {3-89275-026-2},
  pages     = {S. A - E, 173 S. : graph. Darst.},
  year      = {2000},
  language  = {de}
}
@book{Thielemann2005,
  author    = {Thielemann, Frank},
  title     = {Kooperationen in der Druck- und Medienbranche : Ans{\"a}tze, Erfahrungen, Instrumente / mit Beitr. von Bastian Pelka ... Kurt-Georg Ciesinger; Frank Thielemann (Hrsg.)},
  publisher = {Der Andere Verl.},
  address   = {T{\"o}nning [u.a.]},
  isbn      = {3-89959-291-3},
  pages     = {88 S. : graph. Darst.},
  year      = {2005},
  language  = {de}
}
@book{Thielemann1994,
  author    = {Thielemann, Frank},
  title     = {Sicherung der Wettbewerbsf{\"a}higkeit durch zwischenbetriebliche Kooperation},
  publisher = {IBI - Ges. f{\"u}r Innovationsforschung},
  address   = {D{\"u}sseldorf [u.a.]},
  pages     = {32 Bl : graph. Darst.},
  year      = {1994},
  language  = {de}
}
@article{Thielemann1998,
  author    = {Thielemann, Frank},
  title     = {Mit strategischen Allianzen ins n{\"a}chste Jahrtausend},
  series = {Druckspiegel. 53 (1998), H. 5},
  journal   = {Druckspiegel. 53 (1998), H. 5},
  isbn      = {0012-6500},
  pages     = {21 -- 24},
  year      = {1998},
  language  = {de}
}
@book{Thielemann1996,
  author    = {Thielemann, Frank},
  title     = {Die Gestaltung von Kooperationen kleiner und mittlerer Unternehmen},
  publisher = {IAI, Institut f{\"u}r Angewandte Innovationsforschung},
  address   = {Bochum},
  isbn      = {3-928854-06-2},
  pages     = {II, 285 S.: graph. Darst},
  year      = {1996},
  language  = {de}
}
@book{Thielemann1999,
  author    = {Thielemann, Frank},
  title     = {Bilanzen - ein komprimierter {\"U}berblick : Intensivkurs zum betrieblichen Rechnungswesen},
  publisher = {MA, Akad.-Verl.- und Druck-Ges.},
  address   = {Essen},
  isbn      = {3-89275-026-2},
  pages     = {E, 167 S. : graph. Darst.},
  year      = {1999},
  language  = {de}
}
@book{Thielemann1999,
  author    = {Thielemann, Frank},
  title     = {Die Anfertigung wissenschaftlicher Arbeiten und ihre Pr{\"a}sentation - ein komprimierter Einstieg},
  publisher = {MA, Akademie-Verl.- und Druck-Ges.},
  address   = {Essen},
  isbn      = {3-89275-027-0},
  pages     = {49 S. : graph. Darst.},
  year      = {1999},
  language  = {de}
}
@article{Thielemann1998,
  author    = {Thielemann, Frank},
  title     = {Druckindustrielle Innovation},
  series = {Der Siebdruck. 47 (1998), H. 4},
  journal   = {Der Siebdruck. 47 (1998), H. 4},
  isbn      = {0178-2835},
  pages     = {32 -- ff},
  year      = {1998},
  language  = {de}
}
@article{Thielemann1998,
  author    = {Thielemann, Frank},
  title     = {Mit vereinten Kr{\"a}ften},
  series = {Trockenbau, Akustik : Magazin f{\"u}r Planung und Ausf{\"u}hrung. 15 (1998), H. 5},
  journal   = {Trockenbau, Akustik : Magazin f{\"u}r Planung und Ausf{\"u}hrung. 15 (1998), H. 5},
  isbn      = {0179-8006},
  pages     = {60 -- 68},
  year      = {1998},
  language  = {de}
}
@inproceedings{TewariNeshvadGoldbachetal.2015,
  author    = {Tewari, Udit and Neshvad, Surena and Goldbach, Daniel and Sachau, J{\"u}rgen},
  title     = {Verification and Implementation of Pseudo-Random-Binary-Sequences for Online Determination of Grid Impedance Spectrum},
  series = {International Conference on Renewable Energies and Power Quality (ICREPQ´15), La Conuna, Spain, 25th to 27th March, 2015},
  booktitle = {International Conference on Renewable Energies and Power Quality (ICREPQ´15), La Conuna, Spain, 25th to 27th March, 2015},
  pages     = {6 Seiten},
  year      = {2015},
  language  = {en}
}
@inproceedings{TakenagaHerreraWerneretal.2013,
  author    = {Takenaga, Shoko and Herrera, Cony F. and Werner, Frederik and Biselli, Manfred and Schnitzler, Thomas and Sch{\"o}ning, Michael Josef and {\"O}hlschl{\"a}ger, Peter and Wagner, Torsten},
  title     = {Detection of the metabolic activity of cells by differential measurements based on a single light-addressable potentiometric sensor chip},
  series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  organization    = {Dresdner Sensor-Symposium <11, 2013>},
  isbn      = {978-3-9813484-5-3},
  pages     = {63 -- 67},
  year      = {2013},
  language  = {en}
}
@inproceedings{TaddeiReindlParketal.2011,
  author    = {Taddei, Francesca and Reindl, Lukas and Park, Jin and Butenweg, Christoph and Karadogan, Faruk},
  title     = {Numerical investigation of AAC wall panels based on the damage plasticity constitutive law},
  series = {Cement, Wapno, Beton ; 2011, 7, Special issue: 5th International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' to be held at Bydgoszcz to celebrate 60 years of AAC experience in Poland, Bydgoszcz, September 14-17, 2011},
  booktitle = {Cement, Wapno, Beton ; 2011, 7, Special issue: 5th International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' to be held at Bydgoszcz to celebrate 60 years of AAC experience in Poland, Bydgoszcz, September 14-17, 2011},
  publisher = {Stowarzyszenie Producent{\´o}w Cementu i Wapna},
  address   = {Krakow},
  organization    = {International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' <5, 2011, Bydgoszcz>},
  issn      = {1425-8129},
  pages     = {86 -- 91},
  year      = {2011},
  language  = {en}
}
@inproceedings{TaddeiLozanaMicheletal.2015,
  author    = {Taddei, Francesca and Lozana, Lara and Michel, Philipp and Butenweg, Christoph and Klinkel, Sven},
  title     = {Practical recommendations for the foundation design of onshore wind turbines including soil-structure interaction},
  series = {5th International Conference on Computational Methods in Structural , Hersonissos, Greece Dynamics and Earthquake Engineering, COMPDYN 2015, 25.05.2015-27.05.2015, Hersonissos, Greece.},
  booktitle = {5th International Conference on Computational Methods in Structural , Hersonissos, Greece Dynamics and Earthquake Engineering, COMPDYN 2015, 25.05.2015-27.05.2015, Hersonissos, Greece.},
  editor    = {Papadrakakis, Manolis and Papadrakakis, M. and Papadopoulos, V. and Plevris, V.},
  year      = {2015},
  language  = {en}
}
@article{TaddeiButenwegKlinkel2015,
  author    = {Taddei, Francesca and Butenweg, Christoph and Klinkel, S.},
  title     = {Parametric investigation of the soil-structure interaction effects on the dynamic behaviour of a shallow foundation supported wind turbine considering a layered soil},
  series = {Wind energy : an international journal for progress and applications in wind power conversion technology},
  volume    = {Volume 18},
  journal   = {Wind energy : an international journal for progress and applications in wind power conversion technology},
  number    = {Issue 3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1099-1824 (E-Journal); 1095-4244 (Print)},
  doi       = {10.1002/we.1703},
  pages     = {399 -- 417},
  year      = {2015},
  language  = {en}
}
@inproceedings{SurteesGillespieKernetal.2004,
  author    = {Surtees, A. J. and Gillespie, A. and Kern, Alexander and Rousseau, A.},
  title     = {DEVELOPMENT OF A RISK ASSESSMENT CALCULATOR BASED ON A SIMPLIFIED FORM OF THE IEC 62305-2 STANDARD ON LIGHTNING PROTECTION},
  year      = {2004},
  abstract  = {Neue Blitzschutznorm IEC 62305. Entwicklung einer einfachen Software zur Risikoabw{\"a}gung},
  language  = {en}
}
@incollection{StriebingMuellerSchraudneretal.2022,
  author    = {Striebing, Clemens and M{\"u}ller, J{\"o}rg and Schraudner, Martina and Gewinner, Irina Valerie and Guerrero Morales, Patricia and Hochfeld, Katharina and Hoffman, Shekinah and Kmec, Julie A. and Nguyen, Huu Minh and Schneider, Jannick and Sheridan, Jennifer and Steuer-Dankert, Linda and Trimble O'Connor, Lindsey and Vandevelde-Rougale, Agn{\`e}s},
  title     = {Promoting diversity and combatting discrimination in research organizations: a practitioner's guide},
  series = {Diversity and discrimination in research organizations},
  booktitle = {Diversity and discrimination in research organizations},
  publisher = {Emerald Publishing Limited},
  address   = {Bingley},
  isbn      = {978-1-80117-959-1 (Print)},
  doi       = {10.1108/978-1-80117-956-020221012},
  pages     = {421 -- 442},
  year      = {2022},
  abstract  = {The essay is addressed to practitioners in research management and from academic leadership. It describes which measures can contribute to creating an inclusive climate for research teams and preventing and effectively dealing with discrimination. The practical recommendations consider the policy and organizational levels, as well as the individual perspective of research managers. Following a series of basic recommendations, six lessons learned are formulated, derived from the contributions to the edited collection on "Diversity and Discrimination in Research Organizations."},
  language  = {en}
}
@inproceedings{StollenwerkRiekeDahmenetal.2016,
  author    = {Stollenwerk, Dominik and Rieke, C. and Dahmen, Markus and Pieper, Martin},
  title     = {Biogas Production Modelling : A Control System Engineering Approach},
  series = {IOP Conference Series: Earth and Environmental Science. Bd. 32},
  booktitle = {IOP Conference Series: Earth and Environmental Science. Bd. 32},
  issn      = {1755-1315},
  doi       = {10.1088/1755-1315/32/1/012008},
  pages     = {012008/1 -- 012008/4},
  year      = {2016},
  language  = {en}
}
@article{StollenwerkReinkensmeierGeorgetal.2021,
  author    = {Stollenwerk, Dominik and Reinkensmeier, Sebastian and Georg, J{\"o}rg Heiner and Jungbluth, Christian},
  title     = {„Smartes" Laden an {\"o}ffentlich zug{\"a}nglichen Lades{\"a}ulen - Teil 2: USER-Verhalten und -Erwartungen},
  series = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  volume    = {71},
  journal   = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  number    = {3},
  publisher = {ETV Energieverlag},
  address   = {Essen},
  isbn      = {0720-6240},
  issn      = {0013-743X},
  pages     = {38 -- 42},
  year      = {2021},
  language  = {de}
}
@inproceedings{StollenwerkKuvarakulKuperjans2013,
  author    = {Stollenwerk, Dominik and Kuvarakul, T. and Kuperjans, Isabel},
  title     = {Renewable energy supply for power dominated, energy intense production processes - a systematic conversion approach for the anodizing process},
  series = {IOP conference series: Earth and environmental science (EES)},
  volume    = {Vol. 16},
  booktitle = {IOP conference series: Earth and environmental science (EES)},
  number    = {H. 1},
  issn      = {1755-1315},
  pages     = {012142/1 -- 012142/4},
  year      = {2013},
  language  = {en}
}
@incollection{StollenwerkFranzkeMaureretal.2023,
  author    = {Stollenwerk, Dominik and Franzke, Till and Maurer, Florian and Reinkensmeier, Sebastian and Kim, Franken and Tambornino, Philipp and Haas, Florian and Rieke, Christian and Hermanuz, Andreas and Borchert, J{\"o}rg and Ritz, Thomas and Sander, Volker},
  title     = {Smarte Lades{\"a}ulen : Netz- und Marktdienliches {\"o}ffentliches Laden},
  series = {Towards the New Normal in Mobility : Technische und betriebswirtschaftliche Aspekte},
  booktitle = {Towards the New Normal in Mobility : Technische und betriebswirtschaftliche Aspekte},
  editor    = {Proff, Heike},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-39437-0 (Print)},
  doi       = {10.1007/978-3-658-39438-7_18},
  pages     = {287 -- 304},
  year      = {2023},
  abstract  = {Stand 01.01.2022 sind in Deutschland 618.460 elektrisch angetriebene KFZ zugelassen. Insgesamt sind derzeit 48.540.878 KFZ zugelassen, was einer Elektromobilit{\"a}tsquote von ca. 1,2 \% entspricht. Derzeit werden Elektromobile {\"u}ber Ladestationen oder Steckdosen mit dem Stromnetz verbunden und {\"u}blicherweise mit der vollen Ladekapazit{\"a}t des Anschlusses aufgeladen, bis das Batteriemanagementsystem des Fahrzeugs abh{\"a}ngig vom Ladezustand der Batterie die Ladeleistung reduziert.},
  language  = {de}
}
@article{StockMalindretosIndlekoferetal.2001,
  author    = {Stock, J. and Malindretos, J. and Indlekofer, K.M. and P{\"o}ttgens, Michael and F{\"o}rster, Arnold and L{\"u}th, Hans},
  title     = {A Vertical Resonant Tunneling Transistor for Application in Digital Logic Circuits},
  series = {IEEE Transactions on Electron Devices (T-ED). 48 (2001), H. 6},
  journal   = {IEEE Transactions on Electron Devices (T-ED). 48 (2001), H. 6},
  isbn      = {0018-9383},
  pages     = {1028 -- 1032},
  year      = {2001},
  language  = {en}
}
@article{SteuerDankertSharmaBlecketal.2017,
  author    = {Steuer-Dankert, Linda and Sharma, Mamta Rameshwarlal and Bleck, Wolfgang and Leicht-Scholten, Carmen},
  title     = {Diversity and innovation management in large research groups},
  series = {International Journal of Innovation Management},
  volume    = {5},
  journal   = {International Journal of Innovation Management},
  number    = {2},
  issn      = {1757-5877},
  pages     = {49 -- 72},
  year      = {2017},
  abstract  = {Contemporary research appreciates a diverse workforce as a potential source of innovation. Researchers explore the fine details of why diversity management is central for generating innovations in heterogeneous research groups and how it could be effectively implemented into organizations. Complex research associations that discuss topics with a high impact on society increasingly address the necessity of establishing a diverse workforce to confront the challenges of tomorrow. Characterized by complex management structures as well as hierarchies, research associations have not been a subject of investigation until now. For this reason, the presented research project aims to develop a diversity and innovation management strategy with the ultimate goal of inducing change in the corporate culture. The proposed approach consisted of six phases; the first two phases investigated the status quo of diversity in the existing organizational structures of member institutes and the variety of particular working cultures within the research association. The third and the fourth phases utilized qualitative and quantitative studies. The third phase focused on the connection of management level to diversity and innovation, and the need for diversity and innovation management, and tailor-made methods of implementing them. The first three phases have been accomplished successfully; preliminary results are already available. The fourth phase will mainly focus on exploring the mind-set of the employees. The fifth phase will consolidate the findings in the first four phases into an implementable strategy. The final phase will address the implementation of this strategy into the organization. Phases 4 to 6 have not yet been undertaken},
  language  = {en}
}
@inproceedings{SteuerDankertSharmaBlecketal.2017,
  author    = {Steuer-Dankert, Linda and Sharma, Mamta Rameshwarlal and Bleck, Wolfgang and Leicht-Scholten, Carmen},
  title     = {Innovation through Diversity - Development of a Diversity and Innovation management concept},
  series = {International Conference on Innovation and Management : IAM23017S : Date: July 4-7, 2017, Osaka, Japan},
  booktitle = {International Conference on Innovation and Management : IAM23017S : Date: July 4-7, 2017, Osaka, Japan},
  editor    = {Farn, C. K.},
  publisher = {Kuang Hui Chiu},
  address   = {Osaka},
  issn      = {2218-6387},
  pages     = {Panel C},
  year      = {2017},
  abstract  = {Acknowledging that a diverse workforce could be a potential source of innovation, the current research deals with the fine details of why diversity management is central to achieving innovation in heterogeneous research groups and how this could be effectively realized in an organization. The types of heterogeneities addressed mainly include gender, qualification, academic discipline and intercultural perspectives. The type of organization being dealt with in this work is a complex association of research institutes at a technical university in Germany (RWTH Aachen University), namely a 'Cluster of Excellence', whereby several institutes of the university work collaboratively in different sub-projects. The 'Cluster of Excellence' is a part of the 'Excellence Initiative' of the German federal and state governments German Research Foundation (DFG) and German Council of Science and Humanities, with the ultimate aim of promoting cutting-edge research. To support interdisciplinary collaboration and thus the performance of the cluster, the development of a diversity and innovation management concept is presently in the conceptual phase and will be described in the frame of this paper. The 3-S-Diversity Model, composed of the three elements: skills, structure and strategy, serves as a basis for the development of the concept. The proposed concept consists of six phases; the first two phases lay the ground work by developing an understanding of the status quo on the forms of diversity in the Cluster of Excellence, the type of organizational structure of the member institutes and the varieties of specialist work cultures of the same. The third and the fourth phases build up on this foundation by means of qualitative and quantitative studies. While the third phase deals with the sensitization of the management level to the close connection between diversity and innovation; the need to manage them thereafter and find tailor-made methods of doing so, the fourth phase shall mainly focus on the mindset of the employees in this regard. The fifth phase shall consolidate the learnings and the ideas developed in the course of the first four phases into an implementable strategy. The ultimate phase shall be the implementation of this concept in the Cluster. The first three phases have been accomplished successfully and the preliminary results are already available.},
  language  = {en}
}
@inproceedings{SteuerDankertLeichtScholten2019,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Diversity- and innovation management in complex engineering organizations},
  series = {7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia},
  booktitle = {7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia},
  editor    = {Tipurić, Darko and Hruška, Domagoj},
  publisher = {Governance Research and Development Centre (CIRU)},
  address   = {Zagreb},
  pages     = {136 -- 157},
  year      = {2019},
  abstract  = {Diversity is increasingly being addressed as an innovation-promoting factor. For this reason, companies and institutions tackle the integration of a diversity management approach that enables a heterogenic perspective on innovation development. However, system-theoretical frameworks state that the implementation of diversity measures that are not tailored to the needs of the organization often leads to a rejection or reactivity with regard to the management approach. In this context, especially organizations, which are characterized by a specific hierarchical structure, a dominant habitus or specialist culture, must face the challenge of realizing a sustainable change of the corporate culture that sets the basis for implementing diversity management approaches. The presented research project focuses on analyzing the situation in a huge scientific collaborative project - so called Cluster of Excellence (CoE) - with the aim to implement a diversity - and innovation management strategy. Considering the influencing determinants, the CoE is characterized by its embeddedness in the scientific system, a complex organizational structure, and a high fluctuation rate. The paper presents a systemic approach of reflecting these factors in order to develop a diversity- and innovation management strategy. In this frame, the results of a quantitative survey of CoE employees and derived mindset-types are presented. The results show a need for taking different mindset-types into account, to be able to develop a tailored management strategy. The aim of the project is to give recommendations for developing a sustainable management concept that promotes both diversity and innovation by drawing on the persisting mindsets of organization members while reflecting top down as well as bottom up factors of implementation processes as well as the psychology of change. This paper addresses all who are concerned with the management of human resources in innovation processes and are striving for a cultural change within the framework of complex organizations.},
  language  = {en}
}
@incollection{SteuerDankertLeichtScholten2022,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Perceiving diversity : an explorative approach in a complex research organization.},
  series = {Diversity and discrimination in research organizations},
  booktitle = {Diversity and discrimination in research organizations},
  publisher = {Emerald Publishing Limited},
  address   = {Bingley},
  isbn      = {978-1-80117-959-1 (Print)},
  doi       = {10.1108/978-1-80117-956-020221010},
  pages     = {365 -- 392},
  year      = {2022},
  abstract  = {Diversity management is seen as a decisive factor for ensuring the development of socially responsible innovations (Beacham and Shambaugh, 2011; Sonntag, 2014; L{\´o}pez, 2015; Uebernickel et al., 2015). However, many diversity management approaches fail due to a one-sided consideration of diversity (Thomas and Ely, 2019) and a lacking linkage between the prevailing organizational culture and the perception of diversity in the respective organization. Reflecting the importance of diverse perspectives, research institutions have a special responsibility to actively deal with diversity, as they are publicly funded institutions that drive socially relevant development and educate future generations of developers, leaders and decision-makers. Nevertheless, only a few studies have so far dealt with the influence of the special framework conditions of the science system on diversity management. Focusing on the interdependency of the organizational culture and diversity management especially in a university research environment, this chapter aims in a first step to provide a theoretical perspective on the framework conditions of a complex research organization in Germany in order to understand the system-specific factors influencing diversity management. In a second step, an exploratory cluster analysis is presented, investigating the perception of diversity and possible influencing factors moderating this perception in a scientific organization. Combining both steps, the results show specific mechanisms and structures of the university research environment that have an impact on diversity management and rigidify structural barriers preventing an increase of diversity. The quantitative study also points out that the management level takes on a special role model function in the scientific system and thus has an influence on the perception of diversity. Consequently, when developing diversity management approaches in research organizations, it is necessary to consider the top-down direction of action, the special nature of organizational structures in the university research environment as well as the special role of the professorial level as role model for the scientific staff.},
  language  = {en}
}
@inproceedings{SteuerDankertLeichtScholten2016,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Social responsibility and innovation - Key competencies for engineers},
  series = {ICERI 2016: 9th International Conference of Education, Research and Innovation: Conference Proceedings : Seville (Spain), 14-16 November},
  booktitle = {ICERI 2016: 9th International Conference of Education, Research and Innovation: Conference Proceedings : Seville (Spain), 14-16 November},
  isbn      = {978-84-617-5895-1},
  issn      = {2340-1095},
  doi       = {10.21125/iceri.2016.0353},
  pages     = {5967 -- 5976},
  year      = {2016},
  abstract  = {Engineers are of particular importance for the societies of tomorrow. The big social challenges society has to cope with in future, can only be mastered, if engineers link the development and innovation process closely with the requirements of people. As a result, in the frame of the innovation process engineers have to design and develop products for diverse users. Therefore, the consideration of diversity in this process is a core competence engineers should have. Implementing the consideration of diverse requirements into product design is also linked to the development of sustainable products and thus leads to social responsible research and development, the core concept formulated by the EU. For this reason, future engineers should be educated to look at the technical perspectives of a problem embedded in the related questions within societies they are developing their artefacts for. As a result, the aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. To match the competence profiles of future engineers to the global challenges and the resulting social responsibility, RWTH Aachen University, one of the leading technical universities in Germany, has established the bridging professorship "Gender and Diversity in Engineering" (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. The interdisciplinary teaching concept of the research group pursues an approach which imparts an application oriented Gender and Diversity expertise to future engineers. In the frame of an established teaching concept, which is a result of experiences and expertise of the research group, students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge into their later field of action. In the frame of the conference the institutional approach will be presented as well as the teaching concept which will be introduced by concrete course examples.},
  language  = {en}
}
@inproceedings{SteuerDankertLeichtScholten2017,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Innovation and Diversity : Integrating new perspectives into research associations},
  series = {12th European Conference on Innovation and Entrepreneurship (ECIE 2017) : Paris, France, 21-22 September 2017},
  booktitle = {12th European Conference on Innovation and Entrepreneurship (ECIE 2017) : Paris, France, 21-22 September 2017},
  isbn      = {978-1-911218-54-8},
  pages     = {767 -- 776},
  year      = {2017},
  abstract  = {The link between diversity and innovation is broadly discussed in the context of research and innovation processes. Many institutions and enterprises, specifically in commerce, have already tried to establish sustainable diversity management concepts, in order to increase the diversity of their workforce in addition to establishing a corporate culture of openness. Alongside the creation of a working place where different experiences and skills are valued equally, the entrepreneurial intention is to transfer diversity into economically relevant advantages. Taking into account the potential of diversity in research and innovation processes, the project "Diversity- and Innovation Management" was incorporated within a large interdisciplinary research Cluster. The project's purpose was to study the context between diversity and innovation in research associations and to later develop a customised management concept into an interdisciplinary research Cluster on integrative production technology with full integration. The challenge of such research associations lays in an organisational structure which is often described as being decentralised. Researchers coming from different academic disciplines, while having diverse habits, conduct research on large scientific issues and challenges. In addition, these researchers are socialised in different institutions and university chairs. Theses differences in leadership styles, business cultures and organisational strategies, follow into their research team work. Taking a closer look into the management of human resources suggests that decentral organised recruitment processes, as well as allocation of human resources, lead to a lacking overview in regard to missing competencies, perspectives and backgrounds in research networks. These circumstances are comparable to big corporate groups. While developing a management concept for research associations, these characteristics must be considered. To ensure this, the project follows a human-centred approach, which considers top-down, as well as bottom-up perspectives. This paper presents the applied mixed-method approach in the scientific issue described above. In the frame of the Cluster of Excellence "Integrative Production Technology for High-Wage Countries" research results based on quantitative, as well as qualitative studies, were presented as an application example. This paper provides a new perspective on the innovation and diversity context. Against the background of complex research organisations, the development approach of a management concept is particularly interesting.},
  language  = {en}
}
@article{SteuerDankertGilmartinMulleretal.2019,
  author    = {Steuer-Dankert, Linda and Gilmartin, Shannon K. and Muller, Carol B. and Dungs, Carolin and Sheppard, Sheri and Leicht-Scholten, Carmen},
  title     = {Expanding engineering limits : a concept for socially responsible education of engineers},
  series = {The international journal of engineering education},
  volume    = {35},
  journal   = {The international journal of engineering education},
  number    = {2},
  isbn      = {0949-149X},
  pages     = {658 -- 673},
  year      = {2019},
  language  = {en}
}
@incollection{SteuerDankertBouffierGaedickeetal.2017,
  author    = {Steuer-Dankert, Linda and Bouffier, Anna and Gaedicke, Sonja and Leicht-Scholten, Carmen},
  title     = {Diversifying engineering education: a transdisciplinary approach from RWTH Aachen University},
  series = {Strategies for increasing diversity in engineering majors and careers},
  booktitle = {Strategies for increasing diversity in engineering majors and careers},
  publisher = {IGI Global},
  address   = {Hershey, USA},
  isbn      = {9781522522126},
  doi       = {10.4018/978-1-5225-2212-6.ch010},
  pages     = {201 -- 235},
  year      = {2017},
  abstract  = {Engineers and therefore engineering education are challenged by the increasing complexity of questions to be answered globally. The education of future engineers therefore has to answer with curriculums that build up relevant skills. This chapter will give an example how to bring engineering and social responsibility successful together to build engineers of tomorrow. Through the integration of gender and diversity perspectives, engineering research and teaching is expanded with new perspectives and contents providing an important potential for innovation. Aiming on the enhancement of engineering education with distinctive competencies beyond technical expertise, the teaching approach introduced in the chapter represents key factors to ensure that coming generations of engineers will be able to meet the requirements and challenges a changing globalized world holds for them. The chapter will describe how this approach successfully has been implemented in the curriculum in engineering of a leading technical university in Germany.},
  language  = {en}
}