@inproceedings{KleineKallweitMichauxetal.2016,
  author    = {Kleine, Harald and Kallweit, Stephan and Michaux, Frank and Havermann, Marc and Olivier, Herbert},
  title     = {PIV Measurement of Shock Wave Diffraction},
  series = {18th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2016, Lissabon},
  booktitle = {18th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2016, Lissabon},
  pages     = {1 -- 14},
  year      = {2016},
  language  = {en}
}
@article{KilicRaatschenKoerfgenetal.2017,
  author    = {Kilic, S. A. and Raatschen, Hans-J{\"u}rgen and K{\"o}rfgen, B. and Apaydin, N. M. and Astaneh-Asl, A.},
  title     = {FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements},
  series = {Arabian Journal for Science and Engineering},
  volume    = {42},
  journal   = {Arabian Journal for Science and Engineering},
  number    = {3},
  publisher = {Springer Nature},
  issn      = {2191-4281},
  doi       = {10.1007/s13369-016-2316-y},
  pages     = {1103 -- 1116},
  year      = {2017},
  abstract  = {This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 \% of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach.},
  language  = {en}
}
@inproceedings{KilicRaatschenAstanehAsletal.2015,
  author    = {Kilic, S. A. and Raatschen, Hans-J{\"u}rgen and Astaneh-Asl, A. and Apaydin, N. M.},
  title     = {Finite element modeling of the Fatih Sultan Mehmet Suspension Bridge},
  series = {Multi-Span Large Bridges - Proceedings of the International Conference on Multi-Span Large Bridges},
  booktitle = {Multi-Span Large Bridges - Proceedings of the International Conference on Multi-Span Large Bridges},
  publisher = {CRC Press},
  address   = {Leiden},
  isbn      = {9781138027572},
  pages     = {1169 -- 1173},
  year      = {2015},
  language  = {en}
}
@article{KesslerBalcGebhardtetal.2015,
  author    = {Kessler, Julia and Balc, Nicolae and Gebhardt, Andreas and Abbas, Karim},
  title     = {Basic Research on Lattice Structures Focused on the Tensile Strength},
  series = {Applied Mechanics and Materials},
  volume    = {Vol. 808},
  journal   = {Applied Mechanics and Materials},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  issn      = {1662-7482},
  doi       = {10.4028/www.scientific.net/AMM.808.193},
  pages     = {193 -- 198},
  year      = {2015},
  language  = {en}
}
@inproceedings{KesslerBalcGebhardtetal.2017,
  author    = {Kessler, Julia and Balc, Nicolae and Gebhardt, Andreas and Abbas, Karim},
  title     = {Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings},
  series = {The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 - CoSME'16},
  booktitle = {The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 - CoSME'16},
  edition   = {Vol. 94},
  doi       = {10.1051/matecconf/20179403008},
  pages     = {7 S.},
  year      = {2017},
  language  = {en}
}
@inproceedings{KesslerBalcGebhardt2016,
  author    = {Kessler, Julia and Balc, Nicolae and Gebhardt, Andreas},
  title     = {Basic research on lattice structures focused on the strut shape and welding beads},
  series = {Physics Procedia},
  volume    = {Vol. 83},
  booktitle = {Physics Procedia},
  issn      = {1875-3884},
  doi       = {10.1016/j.phpro.2016.08.086},
  pages     = {833 -- 838},
  year      = {2016},
  language  = {en}
}
@inproceedings{KaschSchmidtEichleretal.2020,
  author    = {Kasch, Susanne and Schmidt, Thomas and Eichler, Fabian and Thurn, Laura and Jahn, Simon and Bremen, Sebastian},
  title     = {Solution approaches and process concepts for powder bed-based melting of glass},
  series = {Industrializing Additive Manufacturing. Proceedings of AMPA2020},
  booktitle = {Industrializing Additive Manufacturing. Proceedings of AMPA2020},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-54333-4 (Print)},
  doi       = {10.1007/978-3-030-54334-1_7},
  pages     = {82 -- 95},
  year      = {2020},
  abstract  = {In the study, the process chain of additive manufacturing by means of powder bed fusion will be presented based on the material glass. In order to reliably process components additively, new concepts with different solutions were developed and investigated. Compared to established metallic materials, the properties of glass materials differ significantly. Therefore, the process control was adapted to the material glass in the investigations. With extensive parameter studies based on various glass powders such as borosilicate glass and quartz glass, scientifically proven results on powder bed fusion of glass are presented. Based on the determination of the particle properties with different methods, extensive investigations are made regarding the melting behavior of glass by means of laser beams. Furthermore, the experimental setup was steadily expanded. In addition to the integration of coaxial temperature measurement and regulation, preheating of the building platform is of major importance. This offers the possibility to perform 3D printing at the transformation temperatures of the glass materials. To improve the component's properties, the influence of a subsequent heat treatment was also investigated. The experience gained was incorporated into a new experimental system, which allows a much better exploration of the 3D printing of glass. Currently, studies are being conducted to improve surface texture, building accuracy, and geometrical capabilities using three-dimensional specimen. The contribution shows the development of research in the field of 3D printing of glass, gives an insight into the machine and process engineering as well as an outlook on the possibilities and applications.},
  language  = {en}
}
@article{KallweitWillertDuesetal.2008,
  author    = {Kallweit, Stephan and Willert, Chris and Dues, Michael and M{\"u}ller, Ulrich},
  title     = {PIV for Volume Flow Metering / Kallweit, Stephan ; Willert, Chris ; Dues, Michael ; M{\"u}ller, Ulrich ; Lederer, Thomas},
  pages     = {6 S.},
  year      = {2008},
  language  = {en}
}
@article{KallweitVanlanduitVanherzeeleetal.2007,
  author    = {Kallweit, Stephan and Vanlanduit, S. and Vanherzeele, J. and Brouns, M.},
  title     = {Time resolved PIV reconstruction of periodic flows / Vanlanduit, S. ; Vanherzeele, J. ; Kallweit, S. ; Brouns, M. ; Guillaume, P.},
  series = {PIV'07, 7th International Symposium on Particle Image Velocimetry, Roma, IT, Sep 11-14, 2007},
  journal   = {PIV'07, 7th International Symposium on Particle Image Velocimetry, Roma, IT, Sep 11-14, 2007},
  pages     = {1 -- 14},
  year      = {2007},
  language  = {en}
}
@article{KallweitUchiyamaSiekmann1998,
  author    = {Kallweit, Stephan and Uchiyama, R. and Siekmann, H.},
  title     = {Fault Diagnostic Method for Pump Running Conditions Based on Process Modeling and Neural Network / Uchiyama, R. ; Kallweit, S. ; Siekmann, H.},
  series = {International Journal of Rotating Machinery. 4 (1998), H. 1},
  journal   = {International Journal of Rotating Machinery. 4 (1998), H. 1},
  isbn      = {1542-3034},
  pages     = {49 -- 59},
  year      = {1998},
  language  = {en}
}
@article{KallweitSchimpf2003,
  author    = {Kallweit, Stephan and Schimpf, Axel},
  title     = {Photogrammetric Particle Image Velocimetry / Schimpf, Axel ; Kallweit, Stephan},
  series = {Particle image velocimetry : recent improvements; proceedings of the Europiv 2 Workshop held in Zaragoza, Spain, March 31 - April 1, 2003 / edited by M. Stanislas ...},
  journal   = {Particle image velocimetry : recent improvements; proceedings of the Europiv 2 Workshop held in Zaragoza, Spain, March 31 - April 1, 2003 / edited by M. Stanislas ...},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {3-540-21423-2},
  pages     = {295},
  year      = {2003},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2008,
  author    = {Kallweit, Stephan and Kaminsky, Radoslav and Rossi, Massimiliano and Morbiducci, Umberto},
  title     = {PIV Measurements of Flows in Artificial Heart Valves / Kaminsky, Radoslav ; Kallweit, Stephan ; Rossi, Massimiliano ; Morbiducci, Umberto ; Scalise, Lorenzo},
  series = {Particle Image Velocimetry - New Developments and Recent Applications},
  journal   = {Particle Image Velocimetry - New Developments and Recent Applications},
  isbn      = {978-3-540-73528-1},
  pages     = {55 -- 72},
  year      = {2008},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2005,
  author    = {Kallweit, Stephan and Kaminsky, R. and Rossi, M. and Scalise, L.},
  title     = {PIV Measurements with high temporal Resolution behind Artificial Heart Valves / Kaminsky, R. ; Rossi, M. ; Scalise, L. ; Kallweit, S. ; Verdonck, P.},
  series = {Proceedings of the 6th International Symposium on Particle Image Velocimetry},
  journal   = {Proceedings of the 6th International Symposium on Particle Image Velocimetry},
  publisher = {Caltech},
  address   = {Pasadena, CA},
  year      = {2005},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2005,
  author    = {Kallweit, Stephan and Kaminsky, R. and Rossi, M. and Morbiducci, U.},
  title     = {Time resolved PIV technique for high temporal resolution measurements of prosthetic heart valves fluid dynamics / Kaminsky, R. ; Rossi, M. ; Morbiducci, U. ; Scalise, L. ; Catellini, P. ; Kallweit, S. ; Verdonck, P. ; Grigioni, M.},
  series = {The International Journal of Artificial Organs. 28 (2005), H. 9},
  journal   = {The International Journal of Artificial Organs. 28 (2005), H. 9},
  isbn      = {1724-6040},
  pages     = {946},
  year      = {2005},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2005,
  author    = {Kallweit, Stephan and Kaminsky, R. and Rossi, M. and Morbiducci, U.},
  title     = {2D PIV Study of the flow downstream : Two prototypes of a ney monoleaflet artificial aortic heart valve prosthesis / Kaminsky, R. ; Kramm, K. ; Weber, H. J. ; Simons, A. P. ; Kallweit, S. ; Verdonck, P. R.},
  series = {The International Journal of Artificial Organs. 28 (2005), H. 9},
  journal   = {The International Journal of Artificial Organs. 28 (2005), H. 9},
  isbn      = {1724-6040},
  pages     = {921},
  year      = {2005},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2005,
  author    = {Kallweit, Stephan and Kaminsky, R. and Rossi, M. and Morbiducci, U.},
  title     = {3D PIV measurements of prosthetic heart valve dynamics / Kaminsky, R. ; Rossi, M. ; Morbiducci, U. ; Scalise, L. ; Castellini, P. ; Kallweit, S. ; Verdonck, P. ; Grigioni, M.},
  series = {The International Journal of Artificial Organs. 28 (2005), H. 9},
  journal   = {The International Journal of Artificial Organs. 28 (2005), H. 9},
  isbn      = {1724-6040},
  pages     = {868},
  year      = {2005},
  language  = {en}
}
@article{KallweitHelbingOrglmeisteretal.1994,
  author    = {Kallweit, Stephan and Helbing, M. and Orglmeister, R. and Siekmann, H. E.},
  title     = {Image Processing Techniques with Neural Networks for Flow Visualization in Rotating Machinery / Helbing, M. ; Orgimeiste, R. [Orglmeister, R.] ; Kallweit, S. ; Siekmann, H. E. ; Dues, M. ; Cronemeyer, J.},
  series = {FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Lab{\`e}ge / CERT/ONERA. General chairman Patrick Hebrard},
  journal   = {FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Lab{\`e}ge / CERT/ONERA. General chairman Patrick Hebrard},
  address   = {Toulouse},
  pages     = {87 -- 94},
  year      = {1994},
  language  = {en}
}
@incollection{KallweitGottschalkWalenta2016,
  author    = {Kallweit, Stephan and Gottschalk, Michael and Walenta, Robert},
  title     = {ROS based safety concept for collaborative robots in industrial applications},
  series = {Advances in robot design and intelligent control : proceedings of the 24th International Conference on Robotics in Alpe-Adria-Danube Region (RAAD). (Advances in intelligent systems and computing ; 371)},
  booktitle = {Advances in robot design and intelligent control : proceedings of the 24th International Conference on Robotics in Alpe-Adria-Danube Region (RAAD). (Advances in intelligent systems and computing ; 371)},
  publisher = {Springer},
  address   = {Cham},
  organization    = {International Conference on Robotics in Alpe-Adria-Danube Region <24, 2015, Bucharest>},
  isbn      = {978-3-319-21289-0 (Print) ; 978-3-319-21290-6 (E-Book)},
  doi       = {10.1007/978-3-319-21290-6_3},
  pages     = {27 -- 35},
  year      = {2016},
  abstract  = {The production and assembly of customized products increases the demand for flexible automation systems. One approach is to remove the safety fences that separate human and industrial robot to combine their skills. This collaboration possesses a certain risk for the human co-worker, leading to numerous safety concepts to protect him. The human needs to be monitored and tracked by a safety system using different sensors. The proposed system consists of a RGBD camera for surveillance of the common working area, an array of optical distance sensors to compensate shadowing effects of the RGBD camera and a laser range finder to detect the co-worker when approaching the work cell. The software for collision detection, path planning, robot control and predicting the behaviour of the co-worker is based on the Robot Operating System (ROS). A first prototype of the work cell shows that with advanced algorithms from the field of mobile robotics a very flexible safety concept can be realized: the robot not simply stops its movement when detecting a collision, but plans and executes an alternative path around the obstacle.},
  language  = {en}
}
@article{KallweitDuesSiekmann1994,
  author    = {Kallweit, Stephan and Dues, M. W. and Siekmann, H. E.},
  title     = {Spectral Analysis of Pressure Fluctuations and Velocity Fields as Investigated on Propeller Pumps / Dues, M. W. ; Kallweit, S. D. ; Siekmann, H. E.},
  series = {Preprints : Fifth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-5) : May 8 - 11, 1994, Maui Marriott Hotel, Kaanapali, Maui, Hawaii, U.S.A / sponsored by Pacific Center of Thermal-Fluids Engineering. [W.-J. Yang, chairman] / Vol. B.},
  journal   = {Preprints : Fifth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-5) : May 8 - 11, 1994, Maui Marriott Hotel, Kaanapali, Maui, Hawaii, U.S.A / sponsored by Pacific Center of Thermal-Fluids Engineering. [W.-J. Yang, chairman] / Vol. B.},
  pages     = {98 -- 112},
  year      = {1994},
  language  = {en}
}
@article{KallweitDuesSiekmann1994,
  author    = {Kallweit, Stephan and Dues, M. and Siekmann, H.},
  title     = {Particle-Image-Velocimetry (PIV) in rotierenden Maschinen / Dues, M. ; Kallweit, S. ; Siekmann, H.},
  series = {Lasermethoden in der Str{\"o}mungsmesstechnik, 3. Fachtagung der Deutschen Gesellschaft f{\"u}r Laser-Anemometrie (GALA), Bremen, DE, 5.-7. Sep, 1994},
  journal   = {Lasermethoden in der Str{\"o}mungsmesstechnik, 3. Fachtagung der Deutschen Gesellschaft f{\"u}r Laser-Anemometrie (GALA), Bremen, DE, 5.-7. Sep, 1994},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {3-8265-0162-4},
  pages     = {19.1 -- 19-5},
  year      = {1994},
  language  = {en}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@inproceedings{HuberBleckScheiketal.2011,
  author    = {Huber, Fr{\´e}d{\´e}ric and Bleck, Wolfgang and Scheik, Sven and Schleser, Markus and Reisgen, Uwe},
  title     = {Investigation of galvanneal coating adherence in adhesive bonded joints using lap shear test},
  series = {Galvatech 2011 : 8th International Conference on Zinc and Zinc Alloy Coated Steel Sheet, June 21 - 24, 2011, Genova (Italy) ; proceedings},
  booktitle = {Galvatech 2011 : 8th International Conference on Zinc and Zinc Alloy Coated Steel Sheet, June 21 - 24, 2011, Genova (Italy) ; proceedings},
  publisher = {Associazione Italiana di Metallurgia},
  address   = {Mailand},
  organization    = {International Conference on Zinc and Zinc Alloy Coated Steel Sheet <8, 2011, Genua>},
  isbn      = {978-88-85298-82-8},
  pages     = {Paper No. 43},
  year      = {2011},
  language  = {en}
}
@article{HeinrichsWeck1981,
  author    = {Heinrichs, Horst and Weck, H.},
  title     = {Efficient finite-element structural analysis by interactive graphic mesh generation},
  series = {CIRP Annals. 30 (1981), H. 1},
  journal   = {CIRP Annals. 30 (1981), H. 1},
  pages     = {279 -- 284},
  year      = {1981},
  language  = {en}
}
@article{HaselgruberMautnerThiele2010,
  author    = {Haselgruber, Nikolaus and Mautner, Karin and Thiele, Jan},
  title     = {Usage Space Analysis for Reliability Testing},
  series = {Quality and Reliability Engineering International},
  volume    = {26},
  journal   = {Quality and Reliability Engineering International},
  number    = {8},
  publisher = {Wiley},
  address   = {New York},
  issn      = {1099-1638},
  doi       = {10.1002/qre.1155},
  pages     = {877 -- 885},
  year      = {2010},
  abstract  = {During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety.},
  language  = {en}
}
@inproceedings{HartmannKallweitFeldusenetal.2012,
  author    = {Hartmann, Axel and Kallweit, Stephan and Feldusen, Antje and Schr{\"o}der, Wolfgang},
  title     = {Detection of upstream propagating sound waves at buffet flow using high-speed PIV},
  pages     = {14 S. : graph. Darst.},
  year      = {2012},
  language  = {en}
}
@article{HanrathPlesken1985,
  author    = {Hanrath, Wilhelm and Plesken, Wilhelm},
  title     = {Group rings and irreducible representations of space groups / by W. Hanrath and W. Plesken},
  series = {Journal f{\"u}r die reine und angewandte Mathematik. 362 (1985)},
  journal   = {Journal f{\"u}r die reine und angewandte Mathematik. 362 (1985)},
  isbn      = {0075-4102},
  pages     = {130 -- 140},
  year      = {1985},
  language  = {en}
}
@article{HanrathPlesken1984,
  author    = {Hanrath, Wilhelm and Plesken, Wilhelm},
  title     = {The lattices of six-dimensional euclidean space},
  series = {Mathematics of computation. 43 (1984), H. 168},
  journal   = {Mathematics of computation. 43 (1984), H. 168},
  isbn      = {0025-5718},
  pages     = {573 -- 587},
  year      = {1984},
  language  = {en}
}
@article{Hanrath1989,
  author    = {Hanrath, Wilhelm},
  title     = {Character tables of some factor groups of space groups},
  series = {Perfect groups / Derek F. Holt and W. Plesken},
  journal   = {Perfect groups / Derek F. Holt and W. Plesken},
  publisher = {Clarendon Press},
  address   = {Oxford},
  isbn      = {0-19-853559-7},
  pages     = {357 -- 359},
  year      = {1989},
  language  = {en}
}
@article{HaagZontarSchleupenetal.2014,
  author    = {Haag, S. and Zontar, D. and Schleupen, Josef and M{\"u}ller, T. and Brecher, C.},
  title     = {Chain of refined perception in self-optimizing assembly of micro-optical systems},
  series = {Journal of sensors and sensor systems},
  volume    = {3},
  journal   = {Journal of sensors and sensor systems},
  number    = {1},
  publisher = {Copernicus Publ.},
  address   = {G{\"o}ttingen},
  issn      = {2194-878X},
  doi       = {10.5194/jsss-3-87-2014},
  pages     = {87 -- 95},
  year      = {2014},
  abstract  = {Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements - especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base.},
  language  = {en}
}
@inproceedings{GoettscheHinschWittwer1992,
  author    = {G{\"o}ttsche, Joachim and Hinsch, Andreas and Wittwer, Volker},
  title     = {Electrochromic and optical properties of mixed WO3-TiO2 thin films produced by sputtering and the sol-gel technique},
  series = {Optical materials technology for energy efficiency and solar energy conversion XI: chromogenics for smart windows : 19 and 21 May 1992, Toulouse-Lab{\`e}ge. (SPIE proceedings series. 1728)},
  booktitle = {Optical materials technology for energy efficiency and solar energy conversion XI: chromogenics for smart windows : 19 and 21 May 1992, Toulouse-Lab{\`e}ge. (SPIE proceedings series. 1728)},
  editor    = {Hugo-Le Goff, Anne},
  publisher = {SPIE},
  address   = {Bellingham, Wash.},
  isbn      = {0-8194-0901-4},
  pages     = {13 -- 25},
  year      = {1992},
  language  = {en}
}
@article{Grundmann1992,
  author    = {Grundmann, Reinhard},
  title     = {Design Criteria for Aeroacoustic Wind Tunnels},
  year      = {1992},
  language  = {en}
}
@inproceedings{GrossmannGabrielliHerdrichetal.2015,
  author    = {Großmann, Agnes and Gabrielli, Roland Antonius and Herdrich, Georg and Fasoulas, Stefanos and Schnauffer, Peter and Middendorf, Peter and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Overview of the MultiRob 3D Lunar Industrial Development Project},
  series = {Conference Contribution for the 30th ISTS, Kobe, Japan, 04.07.-10.07.2015},
  booktitle = {Conference Contribution for the 30th ISTS, Kobe, Japan, 04.07.-10.07.2015},
  pages     = {8 S.},
  year      = {2015},
  language  = {en}
}
@article{GlowaniaGriesSchoeneetal.2011,
  author    = {Glowania, Michael and Gries, Thomas and Schoene, Jens and Schleser, Markus and Reisgen, Uwe},
  title     = {Innovative coating technology for textile reinforcements of concrete applications},
  series = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)},
  journal   = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  organization    = {International Congress Polymers in Concrete <13, 2010, Funchal, Madeira>},
  isbn      = {978-3-03785-008-4},
  issn      = {1013-9826 (E-Journal) ; 0252-1059 (Print)},
  pages     = {167 -- 173},
  year      = {2011},
  language  = {en}
}
@inproceedings{GerhardsSchleserOttenetal.2019,
  author    = {Gerhards, Benjamin and Schleser, Markus and Otten,, Christian and Schwarz, Alexander and Gebhardt, Andreas},
  title     = {Innovative Laser Beam Joining Technology for Additive Manufactured Parts},
  series = {Conference Proceedings 72nd IIW Annual Assembly and International Conference, 7-12 July 2019, Bratislava},
  booktitle = {Conference Proceedings 72nd IIW Annual Assembly and International Conference, 7-12 July 2019, Bratislava},
  pages     = {1 -- 8},
  year      = {2019},
  language  = {en}
}
@inproceedings{GerhardsSchleserOtten2019,
  author    = {Gerhards, Benjamin and Schleser, Markus and Otten, Christian},
  title     = {Advancements of mobile vacuum laser welding for industrial thick sheet applications},
  series = {Conference Proceedings 72nd IIW Annual Assembly and International Conference, 7-12 July 2019, Bratislava},
  booktitle = {Conference Proceedings 72nd IIW Annual Assembly and International Conference, 7-12 July 2019, Bratislava},
  pages     = {1 -- 8},
  year      = {2019},
  language  = {en}
}
@article{GebhardtSchmidtHoetteretal.2010,
  author    = {Gebhardt, Andreas and Schmidt, Frank-Michael and H{\"o}tter, Jan-Steffen and Sokalla, Wolfgang and Sokalla, Patrick},
  title     = {Additive Manufacturing by selective laser melting the realizer desktop machine and its application for the dental industry},
  series = {Physics Procedia},
  volume    = {5},
  journal   = {Physics Procedia},
  number    = {2},
  isbn      = {1875-3892},
  pages     = {543 -- 549},
  year      = {2010},
  language  = {en}
}
@article{GebhardtSchmidt2002,
  author    = {Gebhardt, Andreas and Schmidt, Frank-Michael},
  title     = {Practical experiences with making and finishing of coloured models using 3D printing},
  year      = {2002},
  language  = {en}
}
@book{GebhardtKesslerThurn2019,
  author    = {Gebhardt, Andreas and Kessler, Julia and Thurn, Laura},
  title     = {3D printing : understanding additive manufacturing},
  edition   = {2. Auflage},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  isbn      = {978-1-56990-702-3},
  pages     = {XVI, 204 Seiten},
  year      = {2019},
  language  = {en}
}
@book{GebhardtHoetter2016,
  author    = {Gebhardt, Andreas and H{\"o}tter, Jan-Steffen},
  title     = {Additive manufacturing : 3D printing for prototyping and manufacturing},
  publisher = {Hanser Publishers},
  address   = {Munich},
  isbn      = {978-1-56990-582-1 ; 978-1-56990-583-8},
  pages     = {591 S.},
  year      = {2016},
  language  = {en}
}
@incollection{GebhardtHoetter2019,
  author    = {Gebhardt, Andreas and Hoetter, Jan-Steffen},
  title     = {Rapid Tooling},
  series = {CIRP Encyclopedia of Production Engineering},
  booktitle = {CIRP Encyclopedia of Production Engineering},
  publisher = {Springer},
  address   = {Berlin, Heidelberg},
  isbn      = {978-3-662-53120-4},
  doi       = {10.1007/978-3-662-53120-4},
  pages     = {39 -- 52},
  year      = {2019},
  language  = {en}
}
@article{GebhardtFateri2013,
  author    = {Gebhardt, Andreas and Fateri, Miranda},
  title     = {3D printing and its applications},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {10},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  number    = {1},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/urn:nbn:de:0009-2-35626},
  year      = {2013},
  abstract  = {Eine zunehmende Anzahl von Artikeln in Publikumszeitschriften und Journalen r{\"u}ckt die direkte Herstellung von Bauteilen und Figuren immer mehr in das Bewusstsein einer breiten {\"O}ffentlichkeit. Leider ergibt sich nur selten ein einigermaßen vollst{\"a}ndiges Bild davon, wie und in welchen Lebensbereichen diese Techniken unseren Alltag ver{\"a}ndern werden. Das liegt auch daran, dass die meisten Artikel sehr technisch gepr{\"a}gt sind und sich nur punktuell auf Beispiele st{\"u}tzen. Dieser Beitrag geht von den Bed{\"u}rfnissen der Menschen aus, wie sie z.B. in der Maslow'schen Bed{\"u}rfnispyramide strukturiert dargestellt sind und unterstreicht dadurch, dass 3D Printing (oder Additive Manufacturing resp. Rapid Prototyping) bereits alle Lebensbereiche erfasst hat und im Begriff ist, viele davon zu revolutionieren.},
  language  = {en}
}
@book{Gebhardt2000,
  author    = {Gebhardt, Andreas},
  title     = {Rapid prototyping : Werkzeug f{\"u}r die schnelle Produktentstehung. - 2., v{\"o}llig {\"u}berarb. Aufl.},
  publisher = {Hanser},
  address   = {M{\"u}nchen [u.a.]},
  isbn      = {3-446-21242-6},
  pages     = {XVII, 409 S. : Ill., graph. Darst.},
  year      = {2000},
  language  = {en}
}
@book{Gebhardt2003,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping},
  publisher = {Hanser},
  address   = {Munich [u.a.]},
  isbn      = {3-446-21259-0},
  pages     = {XV, 379 S. : Ill., graph. Darst.},
  year      = {2003},
  language  = {en}
}
@article{Gebhardt2001,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping and PIV},
  year      = {2001},
  language  = {en}
}
@article{Gebhardt2001,
  author    = {Gebhardt, Andreas},
  title     = {Laserwelding with fillerwire},
  series = {LIA handbook of laser material processing / Laser Institute of America},
  journal   = {LIA handbook of laser material processing / Laser Institute of America},
  address   = {Orlando, Florida},
  isbn      = {3-540-41770-2},
  year      = {2001},
  language  = {en}
}
@article{Gebhardt2004,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping},
  series = {Landolt-B{\"o}rnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: B{\"a}uerle, D. ...},
  journal   = {Landolt-B{\"o}rnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: B{\"a}uerle, D. ...},
  publisher = {Heidelberg},
  address   = {Springer},
  isbn      = {3-540-00105-0},
  pages     = {105 -- 123},
  year      = {2004},
  language  = {en}
}
@book{Gebhardt2011,
  author    = {Gebhardt, Andreas},
  title     = {Understanding Additive Manufacturing : Rapid Prototyping - Rapid Tooling - Rapid Manufacturing},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  isbn      = {978-3-446-42552-1},
  pages     = {VIII, 164 S. : farb. Ill.},
  year      = {2011},
  language  = {en}
}
@inproceedings{GaoBabilonPfaffetal.2018,
  author    = {Gao, H. and Babilon, Katharina and Pfaff, Raphael and Gan, F. and Reich, A.},
  title     = {Model of wheel-rail contact for sanding and adhesion enhancement},
  series = {Proceedings of the 11th International Conference on Contact Mechanics and Wear of Rail/wheel Systems, CM 2018},
  booktitle = {Proceedings of the 11th International Conference on Contact Mechanics and Wear of Rail/wheel Systems, CM 2018},
  isbn      = {978-946186963-0},
  pages     = {314 -- 321},
  year      = {2018},
  language  = {en}
}
@inproceedings{GabrielliMathiesGrossmannetal.2015,
  author    = {Gabrielli, Roland Antonius and Mathies, Johannes and Großmann, Agnes and Herdrich, Georg and Fasoulas, Stefanos and Middendorf, Peter and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Space Propulsion Considerations for a Lunar Take Off Industry Based on Regolith},
  series = {International Symposium on Space Technology and Science (ISTS). July 2015, Kobe, Japan},
  booktitle = {International Symposium on Space Technology and Science (ISTS). July 2015, Kobe, Japan},
  year      = {2015},
  language  = {en}
}
@incollection{FrotscherGossmannRaatschenetal.2015,
  author    = {Frotscher, Ralf and Goßmann, Matthias and Raatschen, Hans-J{\"u}rgen and Temiz Artmann, Ayseg{\"u}l and Staat, Manfred},
  title     = {Simulation of cardiac cell-seeded membranes using the edge-based smoothed FEM},
  series = {Shell and membrane theories in mechanics and biology. (Advanced structured materials ; 45)},
  booktitle = {Shell and membrane theories in mechanics and biology. (Advanced structured materials ; 45)},
  publisher = {Springer},
  address   = {Heidelberg},
  isbn      = {978-3-319-02534-6 ; 978-3-319-02535-3},
  pages     = {187 -- 212},
  year      = {2015},
  abstract  = {We present an electromechanically coupled Finite Element model for cardiac tissue. It bases on the mechanical model for cardiac tissue of Hunter et al. that we couple to the McAllister-Noble-Tsien electrophysiological model of purkinje fibre cells. The corresponding system of ordinary differential equations is implemented on the level of the constitutive equations in a geometrically and physically nonlinear version of the so-called edge-based smoothed FEM for plates. Mechanical material parameters are determined from our own pressure-deflection experimental setup. The main purpose of the model is to further examine the experimental results not only on mechanical but also on electrophysiological level down to ion channel gates. Moreover, we present first drug treatment simulations and validate the model with respect to the experiments.},
  language  = {en}
}
@article{FrohbergAnik1985,
  author    = {Frohberg, Martin G. and Anik, Sabri},
  title     = {The calculation of component activities of binary metallic melts from their gas solubilities},
  series = {Zeitschrift f{\"u}r Metallkunde},
  volume    = {76},
  journal   = {Zeitschrift f{\"u}r Metallkunde},
  number    = {2},
  issn      = {0044-3093},
  pages     = {135 -- 137},
  year      = {1985},
  language  = {en}
}
@article{FrohbergAnik1985,
  author    = {Frohberg, Martin G. and Anik, Sabri},
  title     = {Thermodynamic relations between component activities and gas solubilities in binary metallic systems},
  series = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie},
  volume    = {89},
  journal   = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie},
  number    = {2},
  issn      = {0940-483X},
  pages     = {130 -- 134},
  year      = {1985},
  language  = {en}
}
@article{FrohbergAnik1983,
  author    = {Frohberg, Martin G. and Anik, Sabri},
  title     = {The application of a quadi-chemical lattice model to binary metallic solvents containing oxygen in higher concentrations},
  series = {Zeitschrift f{\"u}r Metallkunde},
  volume    = {74},
  journal   = {Zeitschrift f{\"u}r Metallkunde},
  number    = {10},
  issn      = {0044-3093},
  pages     = {665 -- 666},
  year      = {1983},
  language  = {en}
}
@article{FranzenPindersPfaffetal.2018,
  author    = {Franzen, Julius and Pinders, Erik and Pfaff, Raphael and Enning, Manfred},
  title     = {RailCrowd's virtual fleets: Make most of your asset data},
  series = {Deine Bahn},
  journal   = {Deine Bahn},
  number    = {9},
  publisher = {Bahn-Fachverlag},
  address   = {Berlin},
  issn      = {0948-7263},
  pages     = {11 -- 13},
  year      = {2018},
  abstract  = {For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance - ECM - regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights.},
  language  = {en}
}
@incollection{FranzenSteckenPfaffetal.2019,
  author    = {Franzen, Julian and Stecken, Jannis and Pfaff, Raphael and Kuhlenk{\"o}tter, Bernd},
  title     = {Using the Digital Shadow for a Prescriptive Optimization of Maintenance and Operation : The Locomotive in the Context of the Cyber-Physical System},
  series = {Advances in Production, Logistics and Traffic},
  booktitle = {Advances in Production, Logistics and Traffic},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-13535-5},
  doi       = {10.1007/978-3-030-13535-5_19},
  pages     = {265 -- 276},
  year      = {2019},
  abstract  = {In competition with other modes of transport, rail freight transport is looking for solutions to become more attractive. Short-term success can be achieved through the data-driven optimization of operations and maintenance as well as the application of novel strategies such as prescriptive maintenance. After introducing the concept of prescriptive maintenance, this paper aims to prove that vehicle-focused applications of this approach indeed have the potential to increase attractiveness. However, even greater advantages can be activated if data from the horizontal network of the vehicle is available. Drawing on the state of the art in research and technology in the field of cyber-physical systems (CPS) as well as digital twins and shadows, our work serves to design a system of systems for the horizontal interconnection of a rail vehicle and to conceptualize a draft for a digital twin of a locomotive.},
  language  = {en}
}
@article{FrankoDuKallweitetal.2020,
  author    = {Franko, Josef and Du, Shengzhi and Kallweit, Stephan and Duelberg, Enno Sebastian and Engemann, Heiko},
  title     = {Design of a Multi-Robot System for Wind Turbine Maintenance},
  series = {Energies},
  volume    = {13},
  journal   = {Energies},
  number    = {10},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en13102552},
  pages     = {Article 2552},
  year      = {2020},
  abstract  = {The maintenance of wind turbines is of growing importance considering the transition to renewable energy. This paper presents a multi-robot-approach for automated wind turbine maintenance including a novel climbing robot. Currently, wind turbine maintenance remains a manual task, which is monotonous, dangerous, and also physically demanding due to the large scale of wind turbines. Technical climbers are required to work at significant heights, even in bad weather conditions. Furthermore, a skilled labor force with sufficient knowledge in repairing fiber composite material is rare. Autonomous mobile systems enable the digitization of the maintenance process. They can be designed for weather-independent operations. This work contributes to the development and experimental validation of a maintenance system consisting of multiple robotic platforms for a variety of tasks, such as wind turbine tower and rotor blade service. In this work, multicopters with vision and LiDAR sensors for global inspection are used to guide slower climbing robots. Light-weight magnetic climbers with surface contact were used to analyze structure parts with non-destructive inspection methods and to locally repair smaller defects. Localization was enabled by adapting odometry for conical-shaped surfaces considering additional navigation sensors. Magnets were suitable for steel towers to clamp onto the surface. A friction-based climbing ring robot (SMART— Scanning, Monitoring, Analyzing, Repair and Transportation) completed the set-up for higher payload. The maintenance period could be extended by using weather-proofed maintenance robots. The multi-robot-system was running the Robot Operating System (ROS). Additionally, first steps towards machine learning would enable maintenance staff to use pattern classification for fault diagnosis in order to operate safely from the ground in the future.},
  language  = {en}
}
@inproceedings{FerreinSchifferKallweit2018,
  author    = {Ferrein, Alexander and Schiffer, Stefan and Kallweit, Stephan},
  title     = {The ROSIN Education Concept - Fostering ROS Industrial-Related Robotics Education in Europe},
  series = {ROBOT 2017: Third Iberian Robotics Conference},
  booktitle = {ROBOT 2017: Third Iberian Robotics Conference},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-70836-2},
  doi       = {10.1007/978-3-319-70836-2_31},
  pages     = {370 -- 381},
  year      = {2018},
  language  = {en}
}
@inproceedings{FerreinKallweitLautermann2012,
  author    = {Ferrein, Alexander and Kallweit, Stephan and Lautermann, Mark},
  title     = {Towards an autonomous pilot system for a tunnel boring machine},
  series = {5th Robotics and Mechatronics Conference of South Africa (ROBMECH) : 26 - 27 November 2012 ; CSIR International Conference Centre Gauteng South Africa},
  booktitle = {5th Robotics and Mechatronics Conference of South Africa (ROBMECH) : 26 - 27 November 2012 ; CSIR International Conference Centre Gauteng South Africa},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  isbn      = {978-1-4673-5183-6},
  year      = {2012},
  language  = {en}
}
@article{FeldmannPakGessleretal.2006,
  author    = {Feldmann, Markus and Pak, Daniel and Geßler, Achim and Dilthey, Ulrich and Schleser, Markus},
  title     = {Bonded connections for textile reinforced concrete structures},
  series = {Cailiao-gongcheng = Journal of materials engineering},
  journal   = {Cailiao-gongcheng = Journal of materials engineering},
  number    = {Special iss.},
  issn      = {1001-4381},
  pages     = {123 -- 127},
  year      = {2006},
  language  = {en}
}
@article{FateriHoetterGebhardt2012,
  author    = {Fateri, Miranda and H{\"o}tter, Jan-Steffen and Gebhardt, Andreas},
  title     = {Experimental and Theoretical Investigation of Buckling Deformation of Fabricated Objects by Selective Laser Melting},
  series = {Physics Procedia},
  volume    = {39},
  journal   = {Physics Procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892},
  doi       = {10.1016/j.phpro.2012.10.062},
  pages     = {464 -- 470},
  year      = {2012},
  abstract  = {Although Selective Laser Melting (SLM) process is an innovative manufacturing method, there are challenges such as inferior mechanical properties of fabricated objects. Regarding this, buckling deformation which is caused by thermal stress is one of the undesired mechanical properties which must be alleviated. As buckling deformation is more observable in hard to process materials, silver is selected to be studied theoretically and experimentally for this paper. Different scanning strategies are utilized and a Finite Element Method (FEM) is applied to calculate the temperature gradient in order to determine its effect on the buckling deformation of the objects from experiments.},
  language  = {en}
}
@article{FateriGebhardtThuemmleretal.2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Th{\"u}mmler, Stefan and Thurn, Laura},
  title     = {Experimental investigation on selective laser melting of glass},
  series = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  volume    = {56 (2014)},
  journal   = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892 (E-Journal); 1875-3884 (Print)},
  doi       = {10.1016/j.phpro.2014.08.118},
  pages     = {357 -- 364},
  year      = {2014},
  language  = {en}
}
@inproceedings{FateriGebhardtRenftle2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Renftle, Georg},
  title     = {Additive Manufacturing of Drainage Segments for Cooling System of Crucibles Melting Furnaces},
  series = {International Conference and Expo on Advanced Ceramics and Composites, (ICACC). January 2015, Florida, USA},
  booktitle = {International Conference and Expo on Advanced Ceramics and Composites, (ICACC). January 2015, Florida, USA},
  pages     = {9 S.},
  year      = {2015},
  abstract  = {The cooling process in induction based crucible melting furnaces for Industrial applications is one of the important and challenging factors in production and safety engineering. Accordingly, proper implementation of the cooling system of the furnace using optimum cooling guides and fail-safe features are critical in order to improve the safety of the process. Regarding this, manufacturing of porous material with high electrical isolation for the drainage segments of the cooling channels is examined in this study. Consequently, various geometries with different porosities using glass and ceramic powder are fabricated using Selective Laser Sintering (SLS) process. The manufactured parts are examined in a prototype furnace testing and the feasibility of the SLS manufacturing of parts for this application is discussed.},
  language  = {en}
}
@inproceedings{FateriGebhardtRenftle2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Renftle, Georg},
  title     = {Additive manufacturing of drainage segments for cooling system of crucible melting furnaces},
  series = {Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials II, International Symposium on Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, ICACC 15, 39th International Conference on Advanced Ceramics and Composites, Daytona Beach, FL, US, Jan 25-30, 2015},
  booktitle = {Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials II, International Symposium on Advanced Processing and Manufacturing Technologies for Structural and Multifunctional Materials, ICACC 15, 39th International Conference on Advanced Ceramics and Composites, Daytona Beach, FL, US, Jan 25-30, 2015},
  publisher = {Wiley},
  address   = {Hoboken},
  issn      = {0196-6219},
  doi       = {10.1002/9781119211662.ch14},
  pages     = {123 -- 131},
  year      = {2015},
  language  = {en}
}
@inproceedings{FateriGebhardtKhosravi2013,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Khosravi, Maziar},
  title     = {Experimental investigation of selective laser melting of lunar regolith for in-situ applications},
  series = {ASME 2013 International Mechanical Engineering Congress and Exposition : San Diego, California, USA, November 15-21, 2013. Vol. 2A: Advanced manufacturing},
  booktitle = {ASME 2013 International Mechanical Engineering Congress and Exposition : San Diego, California, USA, November 15-21, 2013. Vol. 2A: Advanced manufacturing},
  publisher = {ASME},
  organization    = {American Society of Mechanical Engineers},
  isbn      = {978-0-7918-5618-5},
  pages     = {V02AT02A008},
  year      = {2013},
  language  = {en}
}
@inproceedings{FateriGebhardtGabriellietal.2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Gabrielli, Roland Antonius and Herdrich, Georg and Fasoulas, Stefanos and Großmann, Agnes and Schnauffer, Peter and Middendorf, Peter},
  title     = {Additive Manufacturing of Lunar Regolith for Extra-terrestrial Industry Plant},
  series = {International Symposium on Space Technology and Science (ICTS). July 2015, Kobe, Japan},
  booktitle = {International Symposium on Space Technology and Science (ICTS). July 2015, Kobe, Japan},
  pages     = {5 S.},
  year      = {2015},
  language  = {en}
}
@inproceedings{FateriGebhardt2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Jewelry fabrication via selective laser melting of glass},
  series = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  booktitle = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  isbn      = {978-0-7918-4583-7},
  doi       = {10.1115/ESDA2014-20380},
  pages     = {V001T06A005},
  year      = {2014},
  abstract  = {Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies applicable for producing complex geometries which are typically expensive or difficult to fabricate using conventional methods. This process has been extensively investigated experimentally for various metals and the fabrication process parameters have been established for different applications; however, fabricating 3D glass objects using SLM technology has remained a challenge so far although it could have many applications. This paper presents a summery on various experimental evaluations of a material database incorporating the build parameters of glass powder using the SLM process for jewelry applications.},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective Laser Melting of Soda-Lime Glass Powder},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1744-7402},
  doi       = {10.1111/ijac.12338},
  pages     = {53 -- 61},
  year      = {2015},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Process Parameters Development of Selective Laser Melting of Lunar Regolith for On-Site Manufacturing Applications},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  isbn      = {1744-7402},
  doi       = {10.1111/ijac.12326},
  pages     = {46 -- 52},
  year      = {2015},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Additive manufactured mechanical disentanglement lock},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {12},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/urn:nbn:de:0009-2-42147},
  year      = {2015},
  language  = {en}
}
@incollection{FateriGebhardt2020,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Introduction to Additive Manufacturing},
  series = {3D Printing of Optical Components},
  booktitle = {3D Printing of Optical Components},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-58960-8},
  doi       = {10.1007/978-3-030-58960-8_1},
  pages     = {1 -- 22},
  year      = {2020},
  abstract  = {Additive manufacturing (AM) works by creating objects layer by layer in a manner similar to a 2D printer with the "printed" layers stacked on top of each other. The layer-wise manufacturing nature of AM enables fabrication of freeform geometries which cannot be fabricated using conventional manufacturing methods as a one part. Depending on how each layer is created and bonded to the adjacent layers, different AM methods have been developed. In this chapter, the basic terms, common materials, and different methods of AM are described, and their potential applications are discussed.},
  language  = {en}
}
@inproceedings{EvansBraunUlmeretal.2022,
  author    = {Evans, Benjamin and Braun, Sebastian and Ulmer, Jessica and Wollert, J{\"o}rg},
  title     = {AAS implementations - current problems and solutions},
  series = {20th International Conference on Mechatronics - Mechatronika (ME)},
  booktitle = {20th International Conference on Mechatronics - Mechatronika (ME)},
  publisher = {IEEE},
  isbn      = {978-1-6654-1040-3},
  doi       = {10.1109/ME54704.2022.9982933},
  pages     = {6 Seiten},
  year      = {2022},
  abstract  = {The fourth industrial revolution presents a multitude of challenges for industries, one of which being the increased flexibility required of manufacturing lines as a result of increased consumer demand for individualised products. One solution to tackle this challenge is the digital twin, more specifically the standardised model of a digital twin also known as the asset administration shell. The standardisation of an industry wide communications tool is a critical step in enabling inter-company operations. This paper discusses the current state of asset administration shells, the frameworks used to host them and their problems that need to be addressed. To tackle these issues, we propose an event-based server capable of drastically reducing response times between assets and asset administration shells and a multi-agent system used for the orchestration and deployment of the shells in the field.},
  language  = {en}
}
@article{EnningZambouAbel2004,
  author    = {Enning, Manfred and Zambou, Nathan and Abel, Dirk},
  title     = {Nonlinear spacing control of following vehicles within platoon a controlled lagrangian approach / Zambou, Nathan ; Enning, Manfred ; Abel, Dirk},
  series = {NOLCOS, IFAC Symposium on Nonlinear Control Systems},
  journal   = {NOLCOS, IFAC Symposium on Nonlinear Control Systems},
  pages     = {1211 -- 1216},
  year      = {2004},
  language  = {en}
}
@article{EnningZambouAbel2005,
  author    = {Enning, Manfred and Zambou, N. and Abel, D.},
  title     = {Longitudinal Control of Following Vehicles within Platoon : A Model-Based Predictive Approach / Zambou, N. ; Enning, M. ; Abel, D.},
  series = {Advances in automotive control 2004 : a proceedings volume from the IFAC symposium, Salerno, Italy, 19 - 23 April 2004 / ed. C. Pianese},
  journal   = {Advances in automotive control 2004 : a proceedings volume from the IFAC symposium, Salerno, Italy, 19 - 23 April 2004 / ed. C. Pianese},
  publisher = {Elsevier},
  address   = {Oxford},
  isbn      = {0080442501},
  pages     = {733 -- 738},
  year      = {2005},
  language  = {en}
}
@article{EnningStuetzleVierecketal.2006,
  author    = {Enning, Manfred and St{\"u}tzle, Thorsten and Viereck, Uwe and Stribersky, Anton},
  title     = {Creepage control for use in wheelslide protection systems / St{\"u}tzle, Thorsten ; Viereck, Uwe ; Stribersky, Anton ; Rulka, Wolfgang ; Enning, Manfred ; Abel, Dirk},
  series = {Control in transportation systems : proceedings of the 11th IFAC symposium on control in transportation systems (CTS 2006), August 29-31, 2006, Delft, the Netherlands / International Federation of Automatic Control},
  journal   = {Control in transportation systems : proceedings of the 11th IFAC symposium on control in transportation systems (CTS 2006), August 29-31, 2006, Delft, the Netherlands / International Federation of Automatic Control},
  isbn      = {0742-5953},
  pages     = {1 CD-ROM},
  year      = {2006},
  language  = {en}
}
@article{EnningMannBolligetal.2003,
  author    = {Enning, Manfred and Mann, S. and Bollig, A. and Kaierle, S.},
  title     = {Autonomous Production Cell for Laser Beam Welding / Mann S. ; Bollig, A. ; Kaierle, S. ; Abel, D. ; Poprawe, R.},
  publisher = {LIA},
  address   = {Orlando, Fla},
  isbn      = {0912035757},
  year      = {2003},
  language  = {en}
}
@article{EnningJenayehMuelleretal.1997,
  author    = {Enning, Manfred and Jenayeh, I. and M{\"u}ller, C. and Rake, Heinrich},
  title     = {Development and realization of a manipulator for automatic decoupling of freight cars in marshalling yards / Jenayeh, I. ; M{\"u}ller, C. ; Enning, Manfred ; Rake, Heinrich ; Peter, J.},
  year      = {1997},
  language  = {en}
}
@article{EnningJenayehMuelleretal.1998,
  author    = {Enning, Manfred and Jenayeh, I. and M{\"u}ller, C. and Kositza, N.},
  title     = {Mechatronics in automating shunting processes in marshalling yards / Jenayeh, I. ; M{\"u}ller, C.; Kositza, N. ; Enning, M. ; Rake, H.},
  series = {Mechatronics '98 : proceedings of the 6th UK Mechatronics Forum International Conference, Sk{\"o}vde, Sweden, 9-11 September 1998},
  journal   = {Mechatronics '98 : proceedings of the 6th UK Mechatronics Forum International Conference, Sk{\"o}vde, Sweden, 9-11 September 1998},
  publisher = {Pergamon},
  address   = {Amsterdam},
  isbn      = {0-08-043339-1},
  pages     = {xxi, 918 S. : graph. Darst.},
  year      = {1998},
  language  = {en}
}
@article{EnningJenayehMuelleretal.1998,
  author    = {Enning, Manfred and Jenayeh, I. and M{\"u}ller, C. and Kositza, N.},
  title     = {A New Approach for Automating Shunting Processes in Marshalling Yards / Jenayeh, I.; M{\"u}ller, C. ; Kositza, N. ; Enning, M. ; Rake, H.},
  series = {Computational Engineering in Systems Applications : 2nd IMACS International Multiconference CESA'98; [abstracts; Nabeul-Hammamet, Tunisia, April 1 - 4, 1998] / ed. by Pierre Borne},
  journal   = {Computational Engineering in Systems Applications : 2nd IMACS International Multiconference CESA'98; [abstracts; Nabeul-Hammamet, Tunisia, April 1 - 4, 1998] / ed. by Pierre Borne},
  publisher = {UCIS},
  address   = {Villeneuve d'Ascq},
  pages     = {338 -- 343},
  year      = {1998},
  language  = {en}
}
@article{EnningHueckerJenayehetal.1999,
  author    = {Enning, Manfred and H{\"u}cker, Jan and Jenayeh, Imad and Rake, Heinrich},
  title     = {A Parametric Identification Scheme for a Self-tuning Industrial Compact Controller - INTERKAMA 1999 / Hucker, Jan ; Jenayeh, Imad ; Enning, Manfred ; Rake, Heinrich},
  year      = {1999},
  language  = {en}
}
@article{EnningBernhardRake1994,
  author    = {Enning, Manfred and Bernhard, S. and Rake, H.},
  title     = {Automation of a laboratory plant for direct casting of thin steel strips / Bernhard, S. ; Enning, M. ; Rake, H.},
  series = {Control Engineering Practice. 2 (1994), H. 6},
  journal   = {Control Engineering Practice. 2 (1994), H. 6},
  isbn      = {0967-0661},
  pages     = {961 -- 967},
  year      = {1994},
  language  = {en}
}
@article{EnningBaier2009,
  author    = {Enning, Manfred and Baier, M.},
  title     = {Energetic and operational use of FlexCargoRail freight wagons in the single wagon load traffic / Baier, M. ; Enning, M.},
  series = {Towards zero emission : EVS 24, the 24th International Battery, Hybrid and Fuel Cell Electric Vehicle Symposium \& Exhibition, Stavanger, Norway, May 13 - 16, 2009 ; symposium proceedings / organised by AVERE ... Robert St{\"u}ssi [Hrsg.]},
  journal   = {Towards zero emission : EVS 24, the 24th International Battery, Hybrid and Fuel Cell Electric Vehicle Symposium \& Exhibition, Stavanger, Norway, May 13 - 16, 2009 ; symposium proceedings / organised by AVERE ... Robert St{\"u}ssi [Hrsg.]},
  address   = {Stavanger},
  pages     = {CD-Rom},
  year      = {2009},
  language  = {en}
}
@inproceedings{EngemannWiesenKallweitetal.2018,
  author    = {Engemann, Heiko and Wiesen, Patrick and Kallweit, Stephan and Deshpande, Harshavardhan and Schleupen, Josef},
  title     = {Autonomous mobile manipulation using ROS},
  series = {Advances in Service and Industrial Robotics},
  booktitle = {Advances in Service and Industrial Robotics},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-61276-8},
  doi       = {10.1007/978-3-319-61276-8_43},
  pages     = {389 -- 401},
  year      = {2018},
  language  = {en}
}
@incollection{EngemannDuKallweitetal.2020,
  author    = {Engemann, Heiko and Du, Shengzhi and Kallweit, Stephan and Ning, Chuanfang and Anwar, Saqib},
  title     = {AutoSynPose: Automatic Generation of Synthetic Datasets for 6D Object Pose Estimation},
  series = {Machine Learning and Artificial Intelligence. Proceedings of MLIS 2020},
  booktitle = {Machine Learning and Artificial Intelligence. Proceedings of MLIS 2020},
  publisher = {IOS Press},
  address   = {Amsterdam},
  isbn      = {978-1-64368-137-5},
  doi       = {10.3233/FAIA200770},
  pages     = {89 -- 97},
  year      = {2020},
  abstract  = {We present an automated pipeline for the generation of synthetic datasets for six-dimension (6D) object pose estimation. Therefore, a completely automated generation process based on predefined settings is developed, which enables the user to create large datasets with a minimum of interaction and which is feasible for applications with a high object variance. The pipeline is based on the Unreal 4 (UE4) game engine and provides a high variation for domain randomization, such as object appearance, ambient lighting, camera-object transformation and distractor density. In addition to the object pose and bounding box, the metadata includes all randomization parameters, which enables further studies on randomization parameter tuning. The developed workflow is adaptable to other 3D objects and UE4 environments. An exemplary dataset is provided including five objects of the Yale-CMU-Berkeley (YCB) object set. The datasets consist of 6 million subsegments using 97 rendering locations in 12 different UE4 environments. Each dataset subsegment includes one RGB image, one depth image and one class segmentation image at pixel-level.},
  language  = {en}
}
@article{EngemannDuKallweitetal.2020,
  author    = {Engemann, Heiko and Du, Shengzhi and Kallweit, Stephan and C{\"o}nen, Patrick and Dawar, Harshal},
  title     = {OMNIVIL - an autonomous mobile manipulator for flexible production},
  series = {Sensors},
  volume    = {20},
  journal   = {Sensors},
  number    = {24, art. no. 7249},
  publisher = {MDPI},
  address   = {Basel},
  isbn      = {1424-8220},
  doi       = {10.3390/s20247249},
  pages     = {1 -- 30},
  year      = {2020},
  language  = {en}
}
@inproceedings{EngemannBadriWenningetal.2019,
  author    = {Engemann, Heiko and Badri, Sriram and Wenning, Marius and Kallweit, Stephan},
  title     = {Implementation of an Autonomous Tool Trolley in a Production Line},
  series = {Advances in Service and Industrial Robotics. RAAD 2019. Advances in Intelligent Systems and Computing, vol 980},
  booktitle = {Advances in Service and Industrial Robotics. RAAD 2019. Advances in Intelligent Systems and Computing, vol 980},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-19648-6},
  doi       = {10.1007/978-3-030-19648-6_14},
  pages     = {117 -- 125},
  year      = {2019},
  language  = {en}
}
@book{EngelnMuellgesUhlig1996,
  author    = {Engeln-M{\"u}llges, Gisela and Uhlig, Frank},
  title     = {Numeric Algorithms with Fortran},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {3-540-60529-0},
  pages     = {XXII, 602 S. : Ill., graph. Darst. + 1 CD-ROM},
  year      = {1996},
  language  = {en}
}
@book{EngelnMuellgesUhlig1996,
  author    = {Engeln-M{\"u}llges, Gisela and Uhlig, Frank},
  title     = {Numerical algorithms with C},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {3-540-60530-0},
  pages     = {XXII, 596 S. : graph. Darst. + 1 CD-ROM},
  year      = {1996},
  language  = {en}
}
@inproceedings{EichlerSkupinThurnetal.2019,
  author    = {Eichler, Fabian and Skupin, Marco and Thurn, Laura and Kasch, Susanne and Schmidt, Thomas},
  title     = {Operating limits for beam melting of glass materials},
  series = {Modern Technologies in Manufacturing (MTeM 2019)},
  volume    = {299},
  booktitle = {Modern Technologies in Manufacturing (MTeM 2019)},
  number    = {Article 01004},
  doi       = {10.1051/matecconf/201929901004},
  pages     = {8 Seiten},
  year      = {2019},
  abstract  = {Laser-based Additive Manufacturing (AM) processes for the use of metals out of the powder bed have been investigated profusely and are prevalent in industry. Although there is a broad field of application, Laser Powder Bed Fusion (LPBF), also known as Selective Laser Melting (SLM) of glass is not fully developed yet. The material properties of glass are significantly different from the investigated metallic material for LPBF so far. As such, the process cannot be transferred, and the parameter limits and the process sequence must be redefined for glass. Starting with the characterization of glass powders, a parameter field is initially confined to investigate the process parameter of different glass powder using LPBFprocess. A feasibility study is carried out to process borosilicate glass powder. The effects of process parameters on the dimensional accuracy of fabricated parts out of borosilicate and hints for the post-processing are analysed and presented in this paper.},
  language  = {en}
}
@article{DuesGebhardtKallweitetal.1994,
  author    = {Dues, M. and Gebhardt, Andreas and Kallweit, Stephan and Scheffler, T. and Siekmann, H. and Uchiyama, T.},
  title     = {Flow Visualization in a Cavitating Flow},
  series = {Proceedings of the German-Japanese Symposium on Multi-Phase Flow : Karlsruhe, Germany, August 23 - 25, 1994 / comp. by U. M{\"u}ller ...},
  journal   = {Proceedings of the German-Japanese Symposium on Multi-Phase Flow : Karlsruhe, Germany, August 23 - 25, 1994 / comp. by U. M{\"u}ller ...},
  publisher = {Kernforschungszentrum Karlsruhe},
  address   = {Karlsruhe},
  pages     = {391 -- 402},
  year      = {1994},
  language  = {en}
}
@inproceedings{DiltheySchleserMoelleretal.2006,
  author    = {Dilthey, Ulrich and Schleser, Markus and M{\"o}ller, M. and Weichhold, O.},
  title     = {Application of polymers in textile reinforced concrete : from the interface to construction elements},
  series = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  booktitle = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  editor    = {Hegger, Josef},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Conference on Textile Reinforced Concrete <1, 2006, Aachen>},
  isbn      = {2-912143-97-7},
  pages     = {55 -- 64},
  year      = {2006},
  language  = {en}
}
@inproceedings{DiltheySchleserHeggeretal.2007,
  author    = {Dilthey, Ulrich and Schleser, Markus and Hegger, Josef and Voss, Stefan},
  title     = {Load-bearing behaviour of polymer-impregnated textiles in concrete},
  series = {Fifth International Workshop on High Performance Fiber Reinforced Cement Composites (HPFRCC 5) : Mainz, July 10 - 13, 2007. (RILEM proceedings. 53)},
  booktitle = {Fifth International Workshop on High Performance Fiber Reinforced Cement Composites (HPFRCC 5) : Mainz, July 10 - 13, 2007. (RILEM proceedings. 53)},
  editor    = {Reinhardt, Hans W.},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Workshop on High Performance Fiber Reinforced Cement Composites <5, 2007, Mainz>},
  isbn      = {978-2-35158-046-2},
  pages     = {183 -- 192},
  year      = {2007},
  language  = {en}
}
@article{DiltheySchleserFeldmannetal.2008,
  author    = {Dilthey, Ulrich and Schleser, Markus and Feldmann, Martin and Pak, Daniel and Geßler, Achim},
  title     = {Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts},
  series = {Cement and concrete composites},
  volume    = {Vol. 30},
  journal   = {Cement and concrete composites},
  number    = {iss. 2},
  issn      = {0958-9465},
  pages     = {82 -- 87},
  year      = {2008},
  language  = {en}
}
@inproceedings{DiltheySchleserChudobaetal.2007,
  author    = {Dilthey, Ulrich and Schleser, Markus and Chudoba, Rostislav and Konrad, Martin},
  title     = {Experimental investigation and micro-mechanical simulaltion of concrete reinforced with epoxy impregnated fabrics},
  series = {Fibre-reinforced polymer reinforcement for concrete structures : proceedings of the 8th international conference : Patras, Greece, July 16- 18, 2007},
  booktitle = {Fibre-reinforced polymer reinforcement for concrete structures : proceedings of the 8th international conference : Patras, Greece, July 16- 18, 2007},
  editor    = {Triantafillou, T. C.},
  publisher = {Univ.},
  address   = {Patras},
  organization    = {International Symposium on Fibre-Reinforced Polymer Reinforcement for Concrete Structures <8, 2007, Patras>},
  isbn      = {9608969107},
  pages     = {456 -- 457},
  year      = {2007},
  language  = {en}
}
@inproceedings{DiltheySchleser2006,
  author    = {Dilthey, Ulrich and Schleser, Markus},
  title     = {Composite improvement of textile reinforced concrete by polymeric impregnation of the textiles},
  series = {International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimar{\~a}es, Portugal},
  booktitle = {International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimar{\~a}es, Portugal},
  editor    = {Barroso de Aguiar, Jose and Jalali, Said and Camoes, Aires and Ferrera, Rui Miguel},
  publisher = {Universidade do Minho, Departamento de Engenharia Civil},
  address   = {Guimar{\~a}es},
  organization    = {International Symposium in Concrete <2006, Guimar{\~a}es)},
  isbn      = {972-99179-1-4},
  pages     = {185 -- 192},
  year      = {2006},
  language  = {en}
}
@inproceedings{DiltheyMundRaupachetal.2004,
  author    = {Dilthey, Ulrich and Mund, F. and Raupach, Michael and Schleser, Markus and Walk-Lauffer, Bernd},
  title     = {Improvement of textile reinforced concrete by polymer additives},
  series = {ICPIC '04 : 11th International Congress on Polymers in Concrete : 2nd-4th June, 2004 at BAM, Berlin, Germany : proceedings / ed. by M. Maultzsch},
  booktitle = {ICPIC '04 : 11th International Congress on Polymers in Concrete : 2nd-4th June, 2004 at BAM, Berlin, Germany : proceedings / ed. by M. Maultzsch},
  publisher = {BAM},
  address   = {Berlin},
  isbn      = {3-00-013706-8},
  pages     = {469 -- 476},
  year      = {2004},
  language  = {en}
}
@article{DiltheyBrandenburgSchleser2004,
  author    = {Dilthey, Ulrich and Brandenburg, Annette and Schleser, Markus},
  title     = {Dispensing and application of unfilled adhesives in the micro range},
  series = {Welding and cutting. 3 (2004), H. 4},
  journal   = {Welding and cutting. 3 (2004), H. 4},
  issn      = {1612-3433},
  pages     = {250 -- 254},
  year      = {2004},
  language  = {en}
}
@inproceedings{DannenSchindelePruemmeretal.2022,
  author    = {Dannen, Tammo and Schindele, Benedikt and Pr{\"u}mmer, Marcel and Arntz, Kristian and Bergs, Thomas},
  title     = {Methodology for the self-optimizing determination of additive manufacturing process eligibility and optimization potentials in toolmaking},
  series = {Procedia CIRP},
  volume    = {107},
  booktitle = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.05.188},
  pages     = {1539 -- 1544},
  year      = {2022},
  abstract  = {Additive Manufacturing (AM) of metallic workpieces faces a continuously rising technological relevance and market size. Producing complex or highly strained unique workpieces is a significant field of application, making AM highly relevant for tool components. Its successful economic application requires systematic workpiece based decisions and optimizations. Considering geometric and technological requirements as well as the necessary post-processing makes deciding effortful and requires in-depth knowledge. As design is usually adjusted to established manufacturing, associated technological and strategic potentials are often neglected. To embed AM in a future proof industrial environment, software-based self-learning tools are necessary. Integrated into production planning, they enable companies to unlock the potentials of AM efficiently. This paper presents an appropriate methodology for the analysis of process-specific AM-eligibility and optimization potential, added up by concrete optimization proposals. For an integrated workpiece characterization, proven methods are enlarged by tooling-specific figures. The first stage of the approach specifies the model's initialization. A learning set of tooling components is described using the developed key figure system. Based on this, a set of applicable rules for workpiece-specific result determination is generated through clustering and expert evaluation. Within the following application stage, strategic orientation is quantified and workpieces of interest are described using the developed key figures. Subsequently, the retrieved information is used for automatically generating specific recommendations relying on the generated ruleset of stage one. Finally, actual experiences regarding the recommendations are gathered within stage three. Statistic learning transfers those to the generated ruleset leading to a continuously deepening knowledge base. This process enables a steady improvement in output quality.},
  language  = {en}
}
@article{CosmaKesslerGebhardtetal.2020,
  author    = {Cosma, Cosmin and Kessler, Julia and Gebhardt, Andreas and Campbell, Ian and Balc, Nicolae},
  title     = {Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed},
  series = {Materials},
  volume    = {13},
  journal   = {Materials},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1944},
  doi       = {10.3390/ma13040905},
  pages     = {1 -- 18},
  year      = {2020},
  abstract  = {To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10\% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250-1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20\% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L.},
  language  = {en}
}
@inproceedings{ChudobaKonradSchleseretal.2009,
  author    = {Chudoba, Rostislav and Konrad, Martin and Schleser, Markus and Meskouris, Konstantin and Reisgen, Uwe},
  title     = {Parametric study of tensile response of TRC specimens reinforced with epoxy-penetrated multi-filament yarns},
  series = {Textilbeton - Theorie und Praxis : Tagungsband zum 4. Kolloquium zu textilbewehrten Tragwerken (CTRS4) und zur 1. Anwendertagung, Dresden, 3.6.2009 - 5.6.2009},
  booktitle = {Textilbeton - Theorie und Praxis : Tagungsband zum 4. Kolloquium zu textilbewehrten Tragwerken (CTRS4) und zur 1. Anwendertagung, Dresden, 3.6.2009 - 5.6.2009},
  editor    = {Curbach, Manfred},
  publisher = {Techn. Univ.},
  address   = {Dresden},
  isbn      = {978-3-86780-122-5},
  pages     = {87 -- 98},
  year      = {2009},
  language  = {en}
}
@article{ChengWollertChenetal.2023,
  author    = {Cheng, Chi-Tsun and Wollert, J{\"o}rg and Chen, Xi and Fapojuwo, Abraham O.},
  title     = {Guest Editorial : Circuits and Systems for Industry X.0 Applications},
  series = {IEEE Journal on Emerging and Selected Topics in Circuits and Systems},
  volume    = {13},
  journal   = {IEEE Journal on Emerging and Selected Topics in Circuits and Systems},
  edition   = {2},
  publisher = {IEEE},
  address   = {New York},
  issn      = {2156-3357 (Print)},
  doi       = {10.1109/JETCAS.2023.3278843},
  pages     = {457 -- 460},
  year      = {2023},
  language  = {en}
}