@article{ReisgenOlschokJakobsetal.2012,
  author    = {Reisgen, Uwe and Olschok, Simon and Jakobs, Stefan and Schleser, Markus and Mokrov, Oleg and Rossiter, Eduardo},
  title     = {Laser beam submerged arc hybrid welding},
  series = {Physics procedia},
  volume    = {39},
  journal   = {Physics procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892},
  doi       = {10.1016/j.phpro.2012.10.016},
  pages     = {75 -- 83},
  year      = {2012},
  abstract  = {The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.},
  language  = {en}
}
@article{ReisertSchneiderGeissleretal.2013,
  author    = {Reisert, Steffen and Schneider, Benno and Geissler, Hanno and Gompel, Matthias van and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Multi-sensor chip for the investigation of different types of metal oxides for the detection of H2O2 in the ppm range},
  series = {physica status solidi (a)},
  volume    = {210},
  journal   = {physica status solidi (a)},
  number    = {5},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  pages     = {898 -- 904},
  year      = {2013},
  abstract  = {In this work, a multi-sensor chip for the investigation of the sensing properties of different types of metal oxides towards hydrogen peroxide in the ppm range is presented. The fabrication process and physical characterization of the multi-sensor chip are described. Pure SnO2 and WO3 as well as Pd- and Pt-doped SnO2 films are characterized in terms of their sensitivity to H2O2. The sensing films have been prepared by drop-coating of water-dispensed nano-powders. A physical characterization, including scanning electron microscopy and X-ray diffraction analysis of the deposited metal-oxide films, was done. From the measurements in hydrogen peroxide atmosphere, it could be shown, that all of the tested metal oxide films are suitable for the detection of H2O2 in the ppm range. The highest sensitivity and reproducibility was achieved using Pt-doped SnO2. Calibration plot of a SnO2, WO3, Pt-, and Pd-doped SnO2 gas sensor for H2O2 concentrations in the ppm range.},
  language  = {en}
}
@article{ReisertHenkelSchneideretal.2010,
  author    = {Reisert, Steffen and Henkel, Hartmut and Schneider, Andreas and Sch{\"a}fer, Daniel and Friedrich, Peter and Berger, J{\"o}rg and Sch{\"o}ning, Michael Josef},
  title     = {Development of a handheld sensor system for the online measurement of hydrogen peroxide in aseptic filling systems},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {913 -- 918},
  year      = {2010},
  language  = {en}
}
@article{ReisertGeisslerFloerkeetal.2013,
  author    = {Reisert, Steffen and Geissler, Hanno and Fl{\"o}rke, Rudolf and Weiler, Christian and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Characterisation of aseptic sterilisation processes using an electronic nose},
  series = {International journal of nanotechnology},
  volume    = {Vol. 10},
  journal   = {International journal of nanotechnology},
  number    = {No. 5-7},
  publisher = {Inderscience Enterprises},
  address   = {Gen{\`e}ve},
  issn      = {1475-7435 (Print) 7141-8151 (Online)},
  pages     = {470 -- 484},
  year      = {2013},
  language  = {en}
}
@article{ReisertGeisslerFloerkeetal.2011,
  author    = {Reisert, Steffen and Geissler, Hanno and Fl{\"o}rke, Rudolf and N{\"a}ther, Niko and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Towards a multi-sensor system for the evaluation of aseptic processes employing hydrogen peroxide vapour (H2O2)},
  series = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  journal   = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1862-6319},
  pages     = {1351 -- 1356},
  year      = {2011},
  language  = {en}
}
@article{ReisertGeisslerWeileretal.2015,
  author    = {Reisert, Steffen and Geissler, H. and Weiler, C. and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Multiple sensor-type system for monitoring the microbicidal effectiveness of aseptic sterilisation processes},
  series = {Food control},
  volume    = {47},
  journal   = {Food control},
  issn      = {1873-7129 (E-Journal); 0956-7135 (Print)},
  doi       = {10.1016/j.foodcont.2014.07.063},
  pages     = {615 -- 622},
  year      = {2015},
  abstract  = {The present work describes a novel multiple sensor-type system for the real-time analysis of aseptic sterilisation processes employing gaseous hydrogen peroxide (H2O2) as a sterilant. The inactivation kinetics of Bacillus atrophaeus by gaseous H2O2 have been investigated by means of a methodical calibration experiment, taking into account the process variables H2O2 concentration, humidity and gas temperature. It has been found that the microbicidal effectiveness at H2O2 concentrations above 2\% v/v is largely determined by the concentration itself, while at lower H2O2 concentrations, the gas temperature and humidity play a leading role. Furthermore, the responses of different types of gas sensors towards the influencing factors of the sterilisation process have been analysed within the same experiment. Based on a correlation established between the inactivation kinetics and the sensor responses, a calorimetric H2O2 sensor and a metal-oxide semiconductor (MOX) sensor have been identified as possible candidates for monitoring the microbicidal effectiveness of aseptic sterilisation processes employing gaseous H2O2. Therefore, two linear models that describe the relationship between sensor response and microbicidal effectiveness have been proposed.},
  language  = {en}
}
@inproceedings{ReisertGeisslerFloerkeetal.2012,
  author    = {Reisert, Steffen and Geissler, H. and Fl{\"o}rke, R. and Weiler, C. and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Characterisation of aseptic sterilisation processes using an electronic nose},
  series = {Nanoscale Science and Technology (NS\&T´12) : Proceedings Book Humboldt Kolleg ; Tunisia, 17-19 March, 2012},
  booktitle = {Nanoscale Science and Technology (NS\&T´12) : Proceedings Book Humboldt Kolleg ; Tunisia, 17-19 March, 2012},
  editor    = {Abdelghani, Adnane and Sch{\"o}ning, Michael Josef},
  pages     = {45 -- 45},
  year      = {2012},
  language  = {en}
}
@article{ReisertGeisslerFlorkeetal.2011,
  author    = {Reisert, Steffen and Geissler, H. and Florke, R. and Wagner, P. and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Controlling aseptic sterilization processes by means of a multi-sensor system},
  publisher = {IEEE},
  address   = {New York},
  pages     = {18 -- 22},
  year      = {2011},
  language  = {en}
}
@article{ReinhardtBitzElOuardietal.2007,
  author    = {Reinhardt, T. and Bitz, Andreas and El Ouardi, A. and Streckert, J. and Sommer, A. and Lerchl, A. and Hansen, V.},
  title     = {Exposure set-ups for in vivo experiments using radial waveguides},
  series = {Radiation Protection Dosimetry},
  volume    = {124},
  journal   = {Radiation Protection Dosimetry},
  number    = {1},
  issn      = {1742-3406},
  doi       = {10.1093/rpd/ncm370},
  pages     = {21 -- 26},
  year      = {2007},
  language  = {en}
}
@inproceedings{ReindlParkNordaetal.2010,
  author    = {Reindl, Lukas and Park, Jin and Norda, Hannah and Butenweg, Christoph},
  title     = {Seismic design of masonry walls subject to out-of-plane bending},
  series = {Proceedings of the Tenth International Conference on Computational Structures Technology : Valencia, Spain, 14 - 17 September 2010 / organised in association with: Universidad Politecnica de Valencia ... Ed. by B. H. V. Topping ...},
  booktitle = {Proceedings of the Tenth International Conference on Computational Structures Technology : Valencia, Spain, 14 - 17 September 2010 / organised in association with: Universidad Politecnica de Valencia ... Ed. by B. H. V. Topping ...},
  publisher = {Civil-Comp Press},
  address   = {Kippen},
  organization    = {International Conference on Computational Structures Technology <10, 2010, Valencia>},
  isbn      = {978-1-905088-36-2},
  doi       = {10.4203/ccp.93.348},
  pages     = {Paper 348},
  year      = {2010},
  language  = {en}
}
@inproceedings{ReindlButenwegKubalski2011,
  author    = {Reindl, Lukas and Butenweg, Christoph and Kubalski, Thomas},
  title     = {Numerical simulation of unreinforced masonry walls subject to dynamic out-of-plane loading},
  series = {COMPDYN 2011 : ECCOMAS Thematic Conference ; Proceedings of the 3rd International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering ; 25-28 May, 2011, Corfu, Greece / Eds.: M. Papadrakakis ...},
  booktitle = {COMPDYN 2011 : ECCOMAS Thematic Conference ; Proceedings of the 3rd International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering ; 25-28 May, 2011, Corfu, Greece / Eds.: M. Papadrakakis ...},
  publisher = {National Technical Univ. of Athens},
  address   = {Athen},
  organization    = {COMPDYN <2011, Corfu>},
  isbn      = {978-960-99994-0-3},
  pages     = {1 -- 10},
  year      = {2011},
  language  = {en}
}
@incollection{ReimerWellmerBraunetal.2009,
  author    = {Reimer, Lars and Wellmer, Georg and Braun, Carsten and Ballmann, Josef},
  title     = {Computational methods for aero-structural analysis and optimisation of aircrafts based on reduced-order structural models},
  series = {MEGADESIGN and MegaOpt - German initiatives for aerodynamic simulation and optimization in aircraft design. Results of the closing symposium of the MEGADESIGN and MegaOpt projects, Braunschweig, Germany, 23 - 24 May, 2007 / Norbert Kroll ... (Eds.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 107},
  booktitle = {MEGADESIGN and MegaOpt - German initiatives for aerodynamic simulation and optimization in aircraft design. Results of the closing symposium of the MEGADESIGN and MegaOpt projects, Braunschweig, Germany, 23 - 24 May, 2007 / Norbert Kroll ... (Eds.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 107},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-642-04092-4},
  pages     = {135 -- 150},
  year      = {2009},
  abstract  = {In this part of the MEGADESIGN project, aeroelastic effects are introduced into the aerodynamic analysis of aircrafts by coupling DLR's flow solvers TAU and FLOWer to a Timoshenko-beam solver. The emerging aeroelastic solvers and a method for the automatic identification of Timoshenko-beam models for wing-box structures were integrated into a simulation environment enabling the combined optimisation of aerodynamic wing shape and structure.},
  language  = {en}
}
@incollection{ReimerBraunWellmeretal.2010,
  author    = {Reimer, Lars and Braun, Carsten and Wellmer, Georg and Behr, Marek and Ballmann, Josef},
  title     = {Development of a modular method for computational aero-structural analysis of aircraft},
  series = {Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schr{\"o}der. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109},
  booktitle = {Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schr{\"o}der. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-642-04087-0},
  pages     = {205 -- 238},
  year      = {2010},
  language  = {en}
}
@inproceedings{ReimerBraunChenetal.2007,
  author    = {Reimer, Lars and Braun, Carsten and Chen, B.-H. and Ballmann, Josef},
  title     = {Computational aeroelastic analysis and design of the HIRENASD wind tunnel wing model and tests},
  series = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden},
  booktitle = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden},
  publisher = {KTH},
  address   = {Stockholm},
  pages     = {1 CD-ROM},
  year      = {2007},
  language  = {en}
}
@inproceedings{ReimerBraunBallmann2006,
  author    = {Reimer, Lars and Braun, Carsten and Ballmann, Josef},
  title     = {Analysis of the static and dynamic aero-structural response of an elastic swept wing model by direct aeroelastic simulation},
  series = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  booktitle = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  publisher = {Optimage},
  address   = {Edinburgh},
  organization    = {International Council of the Aeronautical Sciences (ICAS)},
  isbn      = {0-9533991-7-6},
  pages     = {Paper No. 2006-10.3.3},
  year      = {2006},
  language  = {en}
}
@incollection{ReimerBraunBallmann2007,
  author    = {Reimer, Lars and Braun, Carsten and Ballmann, Josef},
  title     = {Computational study of the aeroelastic equilibrium configuration of a swept wind tunnel wing model in subsonic flow},
  series = {High performance computing in science and engineering '06. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2006 / Wolfgang E. Nagel ... Eds.},
  booktitle = {High performance computing in science and engineering '06. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2006 / Wolfgang E. Nagel ... Eds.},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {978-3-540-36165-7},
  pages     = {421 -- 434},
  year      = {2007},
  abstract  = {In the Collaborative Research Center SFB 401 at RWTH Aachen University, the numerical aeroelastic method SOFIA for direct numerical aeroelastic simulation is being progressively developed. Numerical results obtained by applying SOFIA were compared with measured data of static and dynamic aeroelastic wind tunnel tests for an elastic swept wing in subsonic flow.},
  language  = {en}
}
@article{ReichertDeLucchi2001,
  author    = {Reichert, Gerhard and De Lucchi, Michele},
  title     = {Diffuse Reflexe / Des. Michele De Lucchi, Gerhard Reichert},
  series = {MD - Internatioal magazine of design (2001)},
  journal   = {MD - Internatioal magazine of design (2001)},
  isbn      = {0343-0642},
  pages     = {26 -- 27},
  year      = {2001},
  language  = {en}
}
@article{ReckerBosschaertsWagemakersetal.2010,
  author    = {Recker, Elmar and Bosschaerts, Walter and Wagemakers, Rolf and Hendrick, Patrick and Funke, Harald and B{\"o}rner, Sebastian},
  title     = {Experimental study of a round jet in cross-flow at low momentum ratio},
  series = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1},
  journal   = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1},
  pages     = {1 -- 13},
  year      = {2010},
  language  = {en}
}
@incollection{RebelHueningScholletal.2015,
  author    = {Rebel, S{\"o}ren and H{\"u}ning, Felix and Scholl, Ingrid and Ferrein, Alexander},
  title     = {MQOne: Low-cost design for a rugged-terrain robot platform},
  series = {Intelligent robotics and applications : 8th International Conference, ICIRA 2015, Portsmouth, UK, August 24-27, 2015, Proceedings, Part II (Lecture notes in computer science : vol. 9245)},
  booktitle = {Intelligent robotics and applications : 8th International Conference, ICIRA 2015, Portsmouth, UK, August 24-27, 2015, Proceedings, Part II (Lecture notes in computer science : vol. 9245)},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-22875-4 (print) ; 978-3-319-22876-1 (E-Book)},
  doi       = {10.1007/978-3-319-22876-1_19},
  pages     = {209 -- 221},
  year      = {2015},
  abstract  = {Rugged terrain robot designs are important for field robotics missions. A number of commercial platforms are available, however, at an impressive price. In this paper, we describe the hardware and software component of a low-cost wheeled rugged-terrain robot. The robot is based on an electric children quad bike and is modified to be driven by wire. In terms of climbing properties, operation time and payload it can compete with some of the commercially available platforms, but at a far lower price.},
  language  = {en}
}
@article{RauschKahmannBaltschunetal.2020,
  author    = {Rausch, Valentin and Kahmann, Stephanie Lucina and Baltschun, Christoph and Staat, Manfred and M{\"u}ller, Lars P. and Wegmann, Kilian},
  title     = {Pressure distribution to the distal biceps tendon at the radial tuberosity: a biomechanical study},
  series = {The Journal of Hand Surgery},
  volume    = {45},
  journal   = {The Journal of Hand Surgery},
  number    = {8},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0363-5023},
  doi       = {10.1016/j.jhsa.2020.01.006},
  pages     = {776.e1 -- 776.e9},
  year      = {2020},
  abstract  = {Purpose Mechanical impingement at the narrow radioulnar space of the tuberosity is believed to be an etiological factor in the injury of the distal biceps tendon. The aim of the study was to compare the pressure distribution at the proximal radioulnar space between 2 fixation techniques and the intact state. Methods Six right arms and 6 left arms from 5 female and 6 male frozen specimens were used for this study. A pressure transducer was introduced at the height of the radial tuberosity with the intact distal biceps tendon and after 2 fixation methods: the suture-anchor and the cortical button technique. The force (N), maximum pressure (kPa) applied to the radial tuberosity, and the contact area (mm²) of the radial tuberosity with the ulna were measured and differences from the intact tendon were detected from 60° supination to 60° pronation in 15° increments with the elbow in full extension and in 45° and 90° flexion of the elbow. Results With the distal biceps tendon intact, the pressures during pronation were similar regardless of extension and flexion and were the highest at 60° pronation with 90° elbow flexion (23.3 ± 53.5 kPa). After repair of the tendon, the mean peak pressure, contact area, and total force showed an increase regardless of the fixation technique. Highest peak pressures were found using the cortical button technique at 45° flexion of the elbow and 60° pronation. These differences were significantly different from the intact tendon. The contact area was significantly larger in full extension and 15°, 30°, and 60° pronation using the cortical button technique. Conclusions Pressures on the distal biceps tendon at the radial tuberosity increase during pronation, especially after repair of the tendon. Clinical relevance Mechanical impingement could play a role in both the etiology of primary distal biceps tendon ruptures and the complications occurring after fixation of the tendon using certain techniques.},
  language  = {en}
}
@article{RauschHarbrechtKahmannetal.2020,
  author    = {Rausch, Valentin and Harbrecht, Andreas and Kahmann, Stephanie Lucina and Fenten, Thomas and Jovanovic, Nebojsa and Hackl, Michael and M{\"u}ller, Lars P. and Staat, Manfred and Wegmann, Kilian},
  title     = {Osteosynthesis of Phalangeal Fractures: Biomechanical Comparison of Kirschner Wires, Plates, and Compression Screws},
  series = {The Journal of Hand Surgery},
  volume    = {45},
  journal   = {The Journal of Hand Surgery},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0363-5023},
  doi       = {10.1016/j.jhsa.2020.04.010},
  pages     = {987.e1 -- 987.e8},
  year      = {2020},
  abstract  = {Purpose The aim of this study was to compare several osteosynthesis techniques (intramedullary headless compression screws, T-plates, and Kirschner wires) for distal epiphyseal fractures of proximal phalanges in a human cadaveric model. Methods A total of 90 proximal phalanges from 30 specimens (index, ring, and middle fingers) were used for this study. After stripping off all soft tissue, a transverse distal epiphyseal fracture was simulated at the proximal phalanx. The 30 specimens were randomly assigned to 1 fixation technique (30 per technique), either a 3.0-mm intramedullary headless compression screw, locking plate fixation with a 2.0-mm T-plate, or 2 oblique 1.0-mm Kirschner wires. Displacement analysis (bending, distraction, and torsion) was performed using optical tracking of an applied random speckle pattern after osteosynthesis. Biomechanical testing was performed with increasing cyclic loading and with cyclic load to failure using a biaxial torsion-tension testing machine. Results Cannulated intramedullary compression screws showed significantly less displacement at the fracture site in torsional testing. Furthermore, screws were significantly more stable in bending testing. Kirschner wires were significantly less stable than plating or screw fixation in any cyclic load to failure test setup. Conclusions Intramedullary compression screws are a highly stable alternative in the treatment of transverse distal epiphyseal phalangeal fractures. Kirschner wires seem to be inferior regarding displacement properties and primary stability. Clinical relevance Fracture fixation of phalangeal fractures using plate osteosynthesis may have the advantage of a very rigid reduction, but disadvantages such as stiffness owing to the more invasive surgical approach and soft tissue irritation should be taken into account. Headless compression screws represent a minimally invasive choice for fixation with good biomechanical properties.},
  language  = {en}
}
@inproceedings{RauschLeiseEdereretal.2016,
  author    = {Rausch, Lea and Leise, Philipp and Ederer, Thorsten and Altherr, Lena and Pelz, Peter F.},
  title     = {A comparison of MILP and MINLP solver performance on the example of a drinking water supply system design problem},
  series = {ECCOMAS Congress 2016 VII European Congress on Computational Methods in Applied Sciences and Engineering},
  booktitle = {ECCOMAS Congress 2016 VII European Congress on Computational Methods in Applied Sciences and Engineering},
  editor    = {Papadrakakis, M. and Ppadopoulos, V. and Stefanou, G. and Plevris, V.},
  isbn      = {978-618-82844-0-1},
  pages     = {8509 -- 8527},
  year      = {2016},
  abstract  = {Finding a good system topology with more than a handful of components is a highly non-trivial task. The system needs to be able to fulfil all expected load cases, but at the same time the components should interact in an energy-efficient way. An example for a system design problem is the layout of the drinking water supply of a residential building. It may be reasonable to choose a design of spatially distributed pumps which are connected by pipes in at least two dimensions. This leads to a large variety of possible system topologies. To solve such problems in a reasonable time frame, the nonlinear technical characteristics must be modelled as simple as possible, while still achieving a sufficiently good representation of reality. The aim of this paper is to compare the speed and reliability of a selection of leading mathematical programming solvers on a set of varying model formulations. This gives us empirical evidence on what combinations of model formulations and solver packages are the means of choice with the current state of the art.},
  language  = {en}
}
@inproceedings{RauschFriesenAltherretal.2018,
  author    = {Rausch, Lea and Friesen, John and Altherr, Lena and Pelz, Peter F.},
  title     = {Using mixed-integer programming for the optimal design of water supply networks for slums},
  series = {Operations Research Proceedings 2017},
  booktitle = {Operations Research Proceedings 2017},
  editor    = {Kliewer, Natalia and Ehmke, Jan Fabian and Bornd{\"o}rfer, Ralf},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-89919-0 (Print)},
  doi       = {10.1007/978-3-319-89920-6_68},
  pages     = {509 -- 516},
  year      = {2018},
  abstract  = {The UN sets the goal to ensure access to water and sanitation for all people by 2030. To address this goal, we present a multidisciplinary approach for designing water supply networks for slums in large cities by applying mathematical optimization. The problem is modeled as a mixed-integer linear problem (MILP) aiming to find a network describing the optimal supply infrastructure. To illustrate the approach, we apply it on a small slum cluster in Dhaka, Bangladesh.},
  language  = {en}
}
@article{RauschFriesenAltherretal.2018,
  author    = {Rausch, Lea and Friesen, John and Altherr, Lena and Meck, Marvin and Pelz, Peter F.},
  title     = {A holistic concept to design optimal water supply infrastructures for informal settlements using remote sensing data},
  series = {Remote Sensing},
  volume    = {10},
  journal   = {Remote Sensing},
  number    = {2},
  publisher = {MDPI},
  address   = {Basel},
  isbn      = {2072-4292},
  doi       = {10.3390/rs10020216},
  pages     = {1 -- 23},
  year      = {2018},
  abstract  = {Ensuring access to water and sanitation for all is Goal No. 6 of the 17 UN Sustainability Development Goals to transform our world. As one step towards this goal, we present an approach that leverages remote sensing data to plan optimal water supply networks for informal urban settlements. The concept focuses on slums within large urban areas, which are often characterized by a lack of an appropriate water supply. We apply methods of mathematical optimization aiming to find a network describing the optimal supply infrastructure. Hereby, we choose between different decentral and central approaches combining supply by motorized vehicles with supply by pipe systems. For the purposes of illustration, we apply the approach to two small slum clusters in Dhaka and Dar es Salaam. We show our optimization results, which represent the lowest cost water supply systems possible. Additionally, we compare the optimal solutions of the two clusters (also for varying input parameters, such as population densities and slum size development over time) and describe how the result of the optimization depends on the entered remote sensing data.},
  language  = {en}
}
@article{RauppSchmittWalzetal.2018,
  author    = {Raupp, Sebastian M. and Schmitt, Marcel and Walz, Anna-Lena and Diehm, Ralf and Hummel, Helga and Scharfer, Philip and Schabel, Wilhelm},
  title     = {Slot die stripe coating of low viscous fluids},
  series = {Journal of Coatings Technology and Research},
  volume    = {15},
  journal   = {Journal of Coatings Technology and Research},
  number    = {5},
  publisher = {Springer},
  issn      = {1935-3804},
  doi       = {10.1007/s11998-017-0039-y},
  pages     = {899 -- 911},
  year      = {2018},
  abstract  = {Slot die coating is applied to deposit thin and homogenous films in roll-to-roll and sheet-to-sheet applications. The critical step in operation is to choose suitable process parameters within the process window. In this work, we investigate an upper limit for stripe coatings. This maximum film thickness is characterized by stripe merging which needs to be avoided in a stable process. It is shown that the upper limit reduces the process window for stripe coatings to a major extent. As a result, stripe coatings at large coating gaps and low viscosities are only possible for relatively thick films. Explaining the upper limit, a theory of balancing the side pressure in the gap region in the cross-web direction has been developed.},
  language  = {en}
}
@inproceedings{RaupachOrlowskyBuettneretal.2006,
  author    = {Raupach, Michael and Orlowsky, Jeannette and B{\"u}ttner, T. and Dilthey, Ulrich and Schleser, Markus},
  title     = {Epoxy-impregnated textiles in concrete - load bearing capacity and durability},
  series = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  booktitle = {Textile reinforced concrete : proceedings of the 1. International RILEM Conference, held at the RWTH Aachen, September 6/7, 2006. (RILEM proceedings ; 50)},
  editor    = {Hegger, Josef},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Conference on Textile Reinforced Concrete <1, 2006, Aachen>},
  isbn      = {2-912143-97-7},
  pages     = {77 -- 88},
  year      = {2006},
  language  = {en}
}
@article{RaueWambachGloeggleretal.2014,
  author    = {Raue, Markus and Wambach, M. and Gl{\"o}ggler, S. and Grefen, Dana and Kaufmann, R. and Abetz, C. and Georgopanos, P. and Handge, U. A. and Mang, Thomas and Bl{\"u}mich, B. and Abetz, V.},
  title     = {Investigation of historical hard rubber ornaments of Charles Goodyear},
  series = {Macromolecular chemistry and physics},
  volume    = {Vol. 215},
  journal   = {Macromolecular chemistry and physics},
  number    = {No. 3},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1022-1352},
  pages     = {245 -- 254},
  year      = {2014},
  language  = {en}
}
@article{RauAlexopoulosBreitbachetal.2014,
  author    = {Rau, Christoph and Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Latzke, Markus and Sattler, Johannes Christoph},
  title     = {Transient simulation of a solar-hybrid tower power plant with open volumetric receiver at the location Barstow},
  series = {Energy procedia : proceedings of the SolarPACES 2013 International Conference},
  volume    = {49},
  journal   = {Energy procedia : proceedings of the SolarPACES 2013 International Conference},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102},
  doi       = {10.1016/j.egypro.2014.03.157},
  pages     = {1481 -- 1490},
  year      = {2014},
  abstract  = {In this work the transient simulations of four hybrid solar tower power plant concepts with open-volumetric receiver technology for a location in Barstow-Daggett, USA, are presented. The open-volumetric receiver uses ambient air as heat transfer fluid and the hybridization is realized with a gas turbine. The Rankine cycle is heated by solar-heated air and/or by the gas turbine's flue gases. The plant can be operated in solar-only, hybrid parallel or combined cycle-only mode as well as in any intermediate load levels where the solar portion can vary between 0 to 100\%. The simulated plant is based on the configuration of a solar-hybrid power tower project, which is in planning for a site in Northern Algeria. The meteorological data for Barstow-Daggett was taken from the software meteonorm. The solar power tower simulation tool has been developed in the simulation environment MATLAB/Simulink and is validated.},
  language  = {en}
}
@article{RatkeMilowLisinskietal.2014,
  author    = {Ratke, Lorenz and Milow, Barbara and Lisinski, Susanne and Hoepfner, Sandra},
  title     = {On an effect of fine ceramic particles on the structure of aerogels},
  series = {Microgravity science and technology},
  volume    = {26},
  journal   = {Microgravity science and technology},
  publisher = {Springer Nature},
  address   = {Heidelberg},
  issn      = {0938-0108 ; 1875-0494},
  doi       = {10.1007/s12217-014-9380-2},
  pages     = {103 -- 110},
  year      = {2014},
  language  = {en}
}
@book{RathDzierzynski1995,
  author    = {Rath, Walter and Dzierzynski, Elmar},
  title     = {Solvent-free contact adhesive = L{\"o}sungsmittelfreier Kontaktklebstoff / Rath, Walter ; Dzierzynski, Elmar [Erfinder]},
  publisher = {Europ{\"a}isches Patentamt},
  address   = {M{\"u}nchen},
  year      = {1995},
  language  = {en}
}
@article{RathMottaghy2007,
  author    = {Rath, V. and Mottaghy, Darius},
  title     = {Smooth inversion for ground surface temperature histories: estimating the optimum regularization parameter by generalized cross-validation},
  series = {Geophysical Journal International},
  volume    = {171},
  journal   = {Geophysical Journal International},
  number    = {3},
  issn      = {1365-246X},
  doi       = {10.1111/j.1365-246X.2007.03587.x},
  pages     = {1440 -- 1448},
  year      = {2007},
  language  = {en}
}
@article{RateikeWeyerWiedenmannetal.1981,
  author    = {Rateike, Franz-Matthias and Weyer, K. G. and Wiedenmann, H. and MacGillivray, W. R.},
  title     = {Observation of absorptive optical bistability in a fabry-perot cavity containing multiple atomic beams / K. G. Weyer ; H. Wiedenmann ; M. Rateike ; W. R. Mac Gillivray ; P. Meystre ; H. Walther},
  series = {Optics communications. 37 (1981), H. 6},
  journal   = {Optics communications. 37 (1981), H. 6},
  isbn      = {0030-4018},
  pages     = {426 -- 430},
  year      = {1981},
  language  = {en}
}
@article{RateikeSiebourgSchmidetal.1990,
  author    = {Rateike, Franz-Matthias and Siebourg, W. and Schmid, H. and Anders, S.},
  title     = {Birefringence - An important property of plastic substrates for magneto-optical storage disks / W. Siebourg ; H. Schmid ; F. M. Rateike ; S. Anders ; U. Grigo ; H. L{\"o}wer},
  series = {Polymer engineering \& science / Society of Plastics Engineers. 30 (1990), H. 18},
  journal   = {Polymer engineering \& science / Society of Plastics Engineers. 30 (1990), H. 18},
  isbn      = {0032-3888},
  pages     = {1133 -- 1139},
  year      = {1990},
  language  = {en}
}
@incollection{RaoPathroseHueningetal.2019,
  author    = {Rao, Deepak and Pathrose, Plato and H{\"u}ning, Felix and Sid, Jithin},
  title     = {An Approach for Validating Safety of Perception Software in Autonomous Driving Systems},
  series = {Model-Based Safety and Assessment: 6th International Symposium, IMBSA 2019, Thessaloniki, Greece, October 16-18, 2019, Proceedings},
  booktitle = {Model-Based Safety and Assessment: 6th International Symposium, IMBSA 2019, Thessaloniki, Greece, October 16-18, 2019, Proceedings},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-32872-6},
  doi       = {10.1007/978-3-030-32872-6_20},
  pages     = {303 -- 316},
  year      = {2019},
  abstract  = {The increasing complexity of Advanced Driver Assistance Systems (ADAS) presents a challenging task to validate safe and reliable performance of these systems under varied conditions. The test and validation of ADAS/AD with real test drives, although important, involves huge costs and time. Simulation tools provide an alternative with the added advantage of reproducibility but often use ideal sensors, which do not reflect real sensor output accurately. This paper presents a new validation methodology using fault injection, as recommended by the ISO 26262 standard, to test software and system robustness. In our work, we investigated and developed a tool capable of inserting faults at different software and system levels to verify its robustness. The scope of this paper is to cover the fault injection test for the Visteon's DriveCore™ system, a centralized domain controller for Autonomous driving which is sensor agnostic and SoC agnostic. With this new approach, the validation of safety monitoring functionality and its behavior can be tested using real-world data instead of synthetic data from simulation tools resulting in having better confidence in system performance before proceeding with in-vehicle testing.},
  language  = {en}
}
@article{RamoshabaHuismanLammertynetal.2020,
  author    = {Ramoshaba, Nthai E. and Huisman, Hugo W. and Lammertyn, Leandi and Kotliar, Konstantin and Schutte, Aletta E. and Smith, Wayne},
  title     = {Retinal microvasculature and masked hypertension in young adults: the African-PREDICT study},
  series = {Hypertension Research},
  journal   = {Hypertension Research},
  number    = {43},
  publisher = {Springer Nature},
  address   = {Osaka},
  issn      = {1348-4214},
  doi       = {10.1038/s41440-020-0487-0},
  pages     = {1231 -- 1238},
  year      = {2020},
  abstract  = {Masked hypertension is known to induce microvascular complications. However, it is unclear whether early microvascular changes are already occurring in young, otherwise healthy adults. We therefore investigated whether retinal microvascular calibers and acute responses to a flicker stimulus are related to masked hypertension. We used the baseline data of 889 participants aged 20-30 years who were taking part in the African Prospective study on the Early Detection and Identification of Cardiovascular Disease and Hypertension. Clinic and 24-h ambulatory blood pressure were measured. The central retinal artery equivalent (CRAE) and central retinal vein equivalent were calculated from fundus images, and retinal vessel dilation was determined in response to flicker light-induced provocation. A smaller CRAE was observed in those with masked hypertension vs. those with normotension (157.1 vs. 161.2 measuring units, P < 0.001). In forward multivariable-adjusted regression analysis, only CRAE was negatively related to masked hypertension [adjusted R² = 0.267, β = -0.097 (95\% CI = -0.165; -0.029), P = 0.005], but other retinal microvascular parameters were not associated with masked hypertension. In multivariable logistic regression analyses, masked hypertension [OR = 2.333, (95\% CI = 1.316; 4.241), P = 0.004] was associated with a narrower CRAE. In young healthy adults, masked hypertension was associated with retinal arteriolar narrowing, thereby reflecting early microvascular alterations known to predict cardiovascular outcomes in later life.},
  language  = {en}
}
@article{RamazaniLiMukherjeeetal.2013,
  author    = {Ramazani, Ali and Li, Yang and Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Abdurakhmanov, Aydemir and Schleser, Markus and Reisgen, Uwe},
  title     = {Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding},
  series = {Computational materials science},
  volume    = {Vol. 68},
  journal   = {Computational materials science},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-0801 (E-Book); 0927-0256 (Print)},
  pages     = {107 -- 116},
  year      = {2013},
  language  = {en}
}
@inproceedings{RamanJungHorvathetal.2019,
  author    = {Raman, Aravind Hariharan and Jung, Alexander and Horv{\´a}th, Andr{\´a}s and Becker, Nadine and Staat, Manfred},
  title     = {Modification of a computer model of human stem cell-derived cardiomyocyte electrophysiology based on Patch-Clamp measurements},
  series = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  booktitle = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  editor    = {Staat, Manfred and Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-22-6},
  doi       = {10.17185/duepublico/48750},
  pages     = {10 -- 11},
  year      = {2019},
  abstract  = {Human induced pluripotent stem cells (hiPSCs) have shown to be promising in disease studies and drug screenings [1]. Cardiomyocytes derived from hiPSCs have been extensively investigated using patch-clamping and optical methods to compare their electromechanical behaviour relative to fully matured adult cells. Mathematical models can be used for translating findings on hiPSCCMs to adult cells [2] or to better understand the mechanisms of various ion channels when a drug is applied [3,4]. Paci et al. (2013) [3] developed the first model of hiPSC-CMs, which they later refined based on new data [3]. The model is based on iCells® (Fujifilm Cellular Dynamics, Inc. (FCDI), Madison WI, USA) but major differences among several cell lines and even within a single cell line have been found and motivate an approach for creating sample-specific models. We have developed an optimisation algorithm that parameterises the conductances (in S/F=Siemens/Farad) of the latest Paci et al. model (2018) [5] using current-voltage data obtained in individual patch-clamp experiments derived from an automated patch clamp system (Patchliner, Nanion Technologies GmbH, Munich).},
  language  = {en}
}
@inproceedings{RajanKubalskiAltayetal.2017,
  author    = {Rajan, Sreelakshmy and Kubalski, Thomas and Altay, Okyay and Dalguer, Luis A and Butenweg, Christoph},
  title     = {Multi-dimensional fragility analysis of a RC building with components using response surface method},
  series = {24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017},
  booktitle = {24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017},
  publisher = {International Assn for Structural Mechanics in Reactor Technology (IASMiRT)},
  address   = {Raleigh, USA},
  isbn      = {9781510856776},
  pages     = {3126 -- 3135},
  year      = {2017},
  abstract  = {Conventional fragility curves describe the vulnerability of the main structure under external hazards. However, in complex structures such as nuclear power plants, the safety or the risk depends also on the components associated with a system. The classical fault tree analysis gives an overall view of the failure and contains several subsystems to the main event, however, the interactions in the subsystems are not well represented. In order to represent the interaction of the components, a method suggested by Cimellaro et al. (2006) using multidimensional performance limit state functions to obtain the system fragility curves is adopted. This approach gives the possibility of deriving the cumulative fragility taking into account the interaction of the response of different components. In this paper, this approach is used to evaluate seismic risk of a representative electrical building infrastructure, including the component, of a nuclear power plant. A simplified model of the structure, with nonlinear material behavior is employed for the analysis in Abaqus©. The input variables considered are the material parameters, boundary conditions and the seismic input. The variability of the seismic input is obtained from selected ground motion time histories of spectrum compatible synthetic ccelerograms. Unlike the usual Monte Carlo methods used for the probabilistic analysis of the structure, a computationally effective response surface method is used. This method reduces the computational effort of the calculations by reducing the required number of samples.},
  language  = {en}
}
@inproceedings{RajanHoltschoppenDalgueretal.2016,
  author    = {Rajan, Sreelakshmy and Holtschoppen, B. and Dalguer, L. A. and Klinkel, S. and Butenweg, Christoph},
  title     = {Seismic fragility analysis of a non-conventional reinforced concrete structure considering different uncertainties},
  series = {Proceedings of ISMA2016, International Conference on Noise and Vibration Engineering/USD2016, International Conference on Uncertainty in Structural Dynamics, / ISMA 2016, USD 2016},
  booktitle = {Proceedings of ISMA2016, International Conference on Noise and Vibration Engineering/USD2016, International Conference on Uncertainty in Structural Dynamics, / ISMA 2016, USD 2016},
  editor    = {Sas, P.},
  publisher = {KU Leuven},
  address   = {Leuven},
  pages     = {4213 -- 4225},
  year      = {2016},
  language  = {en}
}
@inproceedings{RajanButenwegDalgueretal.2017,
  author    = {Rajan, S. and Butenweg, Christoph and Dalguer, L. A. and An, J. H. and Renault, P. and Klinkel, S.},
  title     = {Fragility curves for a three-storey reinforced concrete test structure of the international benchmark SMART 2013},
  series = {16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  year      = {2017},
  language  = {en}
}
@incollection{RahierRitzWallenborn2015,
  author    = {Rahier, Michael and Ritz, Thomas and Wallenborn, Ramona},
  title     = {Information and communication technology for integrated mobility concepts such as E-carsharing},
  series = {E-Mobility in Europe : trends and good practice},
  booktitle = {E-Mobility in Europe : trends and good practice},
  publisher = {Springer},
  address   = {Cham [u.a.]},
  isbn      = {978-3-319-13193-1},
  doi       = {10.1007/978-3-319-13194-8_17},
  pages     = {311 -- 326},
  year      = {2015},
  abstract  = {During the past decade attitude towards sharing things has changed extremely. Not just personal data is shared (e.g. in social networks) but also mobility. Together with the increased ecological awareness of the recent years, new mobility concepts have evolved. E-carsharing has become a symbol for these changes of attitude. The management of a shared car fleet, the energy management of electric mobility and the management of various carsharing users with individual likes and dislikes are just some of the major challenges of e-carsharing. Weaving it into integrated mobility concepts, this raises complexity even further. These challenges can only be overcome by an appropriate amount of well-shaped information available at the right place and time. In order to gather, process and share the required information, fleet cars have to be equipped with modern information and communication technology (ICT) and become so-called fully connected cars. Ensuring the usability of these ICT systems is another challenge that is often neglected, even though it is usability that makes carsharing comfortable, attractive and supports users' new attitudes. By means of an integrated and consistent concept for human-machine interaction (HMI), the usability of such systems can be raised tremendously.},
  language  = {en}
}
@article{RaffeisAdjeiKyeremehVroomenetal.2020,
  author    = {Raffeis, Iris and Adjei-Kyeremeh, Frank and Vroomen, Uwe and Westhoff, Elmar and Bremen, Sebastian and Hohoi, Alexandru and B{\"u}hrig-Polaczek, Andreas},
  title     = {Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties},
  series = {Applied Sciences},
  volume    = {10},
  journal   = {Applied Sciences},
  number    = {Art. 3401},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app10103401},
  pages     = {1 -- 15},
  year      = {2020},
  abstract  = {As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni-Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8\% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s-1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20\% to 31\% (V), as well as from 16\% to 25\% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.},
  language  = {en}
}
@article{RachingerBauchStrittmatteretal.2013,
  author    = {Rachinger, Michael and Bauch, Melanie and Strittmatter, Axel and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and Daniel, Rolf and Liebl, Wolfgang and Liesegang, Heiko and Ehrenreich, Armin},
  title     = {Size unlimited markerless deletions by a transconjugative plasmid-system in Bacillus licheniformis},
  series = {Journal of biotechnology},
  volume    = {Vol. 164},
  journal   = {Journal of biotechnology},
  number    = {Iss. 4},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-4863 (E-Journal); 0168-1656 (Print)},
  pages     = {365 -- 369},
  year      = {2013},
  language  = {en}
}
@inproceedings{RabnerShacham2006,
  author    = {Rabner, Arthur and Shacham, Yosi},
  title     = {A concept for a sensitive micro total analysis system for high throughput fluorescence imaging},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1456},
  year      = {2006},
  abstract  = {This paper discusses possible methods for on-chip fluorescent imaging for integrated bio-sensors. The integration of optical and electro-optical accessories, according to suggested methods, can improve the performance of fluorescence imaging. It can boost the signal to background ratio by a few orders of magnitudes in comparison to conventional discrete setups. The methods that are present in this paper are oriented towards building reproducible arrays for high-throughput micro total analysis systems (µTAS). The first method relates to side illumination of the fluorescent material placed into microcompartments of the lab-on-chip. Its significance is in high utilization of excitation energy for low concentration of fluorescent material. The utilization of a transparent µLED chip, for the second method, allows the placement of the excitation light sources on the same optical axis with emission detector, such that the excitation and emission rays are directed controversly. The third method presents a spatial filtering of the excitation background.},
  subject      = {Biosensor},
  language  = {en}
}
@article{RabehiGarlanAchtsnichtetal.2018,
  author    = {Rabehi, Amine and Garlan, Benjamin and Achtsnicht, Stefan and Krause, Hans-Joachim and Offenh{\"a}usser, Andreas and Ngo, Kieu and Neveu, Sophie and Graff-Dubois, Stephanie and Kokabi, Hamid},
  title     = {Magnetic detection structure for Lab-on-Chip applications based on the frequency mixing technique},
  series = {Sensors},
  volume    = {18},
  journal   = {Sensors},
  number    = {6},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s18061747},
  pages     = {14 Seiten},
  year      = {2018},
  abstract  = {A magnetic frequency mixing technique with a set of miniaturized planar coils was investigated for use with a completely integrated Lab-on-Chip (LoC) pathogen sensing system. The system allows the detection and quantification of superparamagnetic beads. Additionally, in terms of magnetic nanoparticle characterization ability, the system can be used for immunoassays using the beads as markers. Analytical calculations and simulations for both excitation and pick-up coils are presented; the goal was to investigate the miniaturization of simple and cost-effective planar spiral coils. Following these calculations, a Printed Circuit Board (PCB) prototype was designed, manufactured, and tested for limit of detection, linear response, and validation of theoretical concepts. Using the magnetic frequency mixing technique, a limit of detection of 15 µg/mL of 20 nm core-sized nanoparticles was achieved without any shielding.},
  language  = {en}
}
@article{RaabKappelKraemeretal.2011,
  author    = {Raab, Monika and Kappel, Sven and Kr{\"a}mer, Andrea and Sanhaji, Mourad and Matthess, Yves and Kurunci-Csacsko, Elisabeth and Calzada-Wack, Julia and Rathkolb, Birgit and Rosman, Jan and Adler, Thure and Busch, Dirk H. and Esposito, Irene and Fuchs, Helmut and Gailus-Durner, Val{\´e}rie and Klingenspor, Martin and Wolf, Eckhard and S{\"a}nger, Nicole and Prinz, Florian and Hrabe de Angelis, Martin and Seibler, Jost and Yuan, Juping and Bergmann, Martin and Knecht, Rainald and Kreft, Bertolt and Strebhardt, Klaus},
  title     = {Toxicity modelling of Plk1-targeted therapies in genetically engineered mice and cultured primary mammalian cells},
  series = {Nature Communications},
  volume    = {2},
  journal   = {Nature Communications},
  number    = {395},
  publisher = {Nature},
  address   = {London},
  issn      = {2041-1723},
  doi       = {10.1038/ncomms1395},
  pages     = {1 -- 11},
  year      = {2011},
  language  = {en}
}
@article{QuittmannMeskemperAlbrachtetal.2020,
  author    = {Quittmann, Oliver J. and Meskemper, Joshua and Albracht, Kirsten and Abel, Thomas and Foitschik, Tina and Str{\"u}der, Heiko K.},
  title     = {Normalising surface EMG of ten upper-extremity muscles in handcycling: Manual resistance vs. sport-specific MVICs},
  series = {Journal of Electromyography and Kinesiology},
  volume    = {51},
  journal   = {Journal of Electromyography and Kinesiology},
  number    = {Article 102402},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1050-6411},
  doi       = {10.1016/j.jelekin.2020.102402},
  year      = {2020},
  abstract  = {Muscular activity in terms of surface electromyography (sEMG) is usually normalised to maximal voluntary isometric contractions (MVICs). This study aims to compare two different MVIC-modes in handcycling and examine the effect of moving average window-size. Twelve able-bodied male competitive triathletes performed ten MVICs against manual resistance and four sport-specific trials against fixed cranks. sEMG of ten muscles [M. trapezius (TD); M. pectoralis major (PM); M. deltoideus, Pars clavicularis (DA); M. deltoideus, Pars spinalis (DP); M. biceps brachii (BB); M. triceps brachii (TB); forearm flexors (FC); forearm extensors (EC); M. latissimus dorsi (LD) and M. rectus abdominis (RA)] was recorded and filtered using moving average window-sizes of 150, 200, 250 and 300 ms. Sport-specific MVICs were higher compared to manual resistance for TB, DA, DP and LD, whereas FC, TD, BB and RA demonstrated lower values. PM and EC demonstrated no significant difference between MVIC-modes. Moving average window-size had no effect on MVIC outcomes. MVIC-mode should be taken into account when normalised sEMG data are illustrated in handcycling. Sport-specific MVICs seem to be suitable for some muscles (TB, DA, DP and LD), but should be augmented by MVICs against manual/mechanical resistance for FC, TD, BB and RA.},
  language  = {en}
}
@article{QuittmannAbelAlbrachtetal.2019,
  author    = {Quittmann, Oliver J. and Abel, Thomas and Albracht, Kirsten and Str{\"u}der, Heiko K.},
  title     = {Reliability of muscular activation patterns and their alterations during incremental handcycling in able-bodied participants},
  series = {Sports Biomechanics},
  journal   = {Sports Biomechanics},
  number    = {Article in press},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1752-6116},
  doi       = {10.1080/14763141.2019.1593496},
  year      = {2019},
  language  = {en}
}
@article{QuittmannAbelAlbrachtetal.2022,
  author    = {Quittmann, Oliver J. and Abel, Thomas and Albracht, Kirsten and Str{\"u}der, Heiko K.},
  title     = {Biomechanics of all-out handcycling exercise: kinetics, kinematics and muscular activity of a 15-s sprint test in able-bodied participants},
  series = {Sports Biomechanics},
  volume    = {21},
  journal   = {Sports Biomechanics},
  number    = {10},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1752-6116 (Onlineausgabe)},
  doi       = {10.1080/14763141.2020.1745266},
  pages     = {1200 -- 1223},
  year      = {2022},
  abstract  = {This study aims to quantify the kinematics, kinetics and muscular activity of all-out handcycling exercise and examine their alterations during the course of a 15-s sprint test. Twelve able-bodied competitive triathletes performed a 15-s all-out sprint test in a recumbent racing handcycle that was attached to an ergometer. During the sprint test, tangential crank kinetics, 3D joint kinematics and muscular activity of 10 muscles of the upper extremity and trunk were examined using a power metre, motion capturing and surface electromyography (sEMG), respectively. Parameters were compared between revolution one (R1), revolution two (R2), the average of revolution 3 to 13 (R3) and the average of the remaining revolutions (R4). Shoulder abduction and internal-rotation increased, whereas maximal shoulder retroversion decreased during the sprint. Except for the wrist angles, angular velocity increased for every joint of the upper extremity. Several muscles demonstrated an increase in muscular activation, an earlier onset of muscular activation in crank cycle and an increased range of activation. During the course of a 15-s all-out sprint test in handcycling, the shoulder muscles and the muscles associated to the push phase demonstrate indications for short-duration fatigue. These findings are helpful to prevent injuries and improve performance in all-out handcycling.},
  language  = {en}
}
@article{QuittmannAbelAlbrachtetal.2020,
  author    = {Quittmann, Oliver J. and Abel, Thomas and Albracht, Kirsten and Meskemper, Joshua and Foitschik, Tina and Str{\"u}der, Heiko K.},
  title     = {Biomechanics of handcycling propulsion in a 30-min continuous load test at lactate threshold: Kinetics, kinematics, and muscular activity in able-bodied participants},
  series = {European Journal of Applied Physiology},
  journal   = {European Journal of Applied Physiology},
  number    = {120},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {1439-6327},
  doi       = {10.1007/s00421-020-04373-x},
  pages     = {1403 -- 1415},
  year      = {2020},
  abstract  = {Purpose This study aims to investigate the biomechanics of handcycling during a continuous load trial (CLT) to assess the mechanisms underlying fatigue in upper body exercise. Methods Twelve able-bodied triathletes performed a 30-min CLT at a power output corresponding to lactate threshold in a racing recumbent handcycle mounted on a stationary ergometer. During the CLT, ratings of perceived exertion (RPE), tangential crank kinetics, 3D joint kinematics, and muscular activity of ten muscles of the upper extremity and trunk were examined using motion capturing and surface electromyography. Results During the CLT, spontaneously chosen cadence and RPE increased, whereas crank torque decreased. Rotational work was higher during the pull phase. Peripheral RPE was higher compared to central RPE. Joint range of motion decreased for elbow-flexion and radial-duction. Integrated EMG (iEMG) increased in the forearm flexors, forearm extensors, and M. deltoideus (Pars spinalis). An earlier onset of activation was found for M. deltoideus (Pars clavicularis), M. pectoralis major, M. rectus abdominis, M. biceps brachii, and the forearm flexors. Conclusion Fatigue-related alterations seem to apply analogously in handcycling and cycling. The most distal muscles are responsible for force transmission on the cranks and might thus suffer most from neuromuscular fatigue. The findings indicate that peripheral fatigue (at similar lactate values) is higher in handcycling compared to leg cycling, at least for inexperienced participants. An increase in cadence might delay peripheral fatigue by a reduced vascular occlusion. We assume that the gap between peripheral and central fatigue can be reduced by sport-specific endurance training.},
  language  = {en}
}
@inproceedings{QuitterMarinoBauschat2019,
  author    = {Quitter, Julius and Marino, Matthew and Bauschat, J.-Michael},
  title     = {Highly Non-Planar Aircraft Configurations: Estimation of Flight Mechanical Derivatives Using Low-Order Methods},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  pages     = {10 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{QuadfliegSchoeneSchleseretal.2012,
  author    = {Quadflieg, Till and Schoene, Jens and Schleser, Markus and Jockenh{\"o}vel, Stefan and Reisgen, Uwe and Gries, Thomas},
  title     = {Shear connectors for hybrid joints of metal and FRP},
  series = {Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference},
  booktitle = {Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference},
  editor    = {Heslehurst, Rikard Benton},
  publisher = {Composites Australia},
  address   = {Hawthorne},
  isbn      = {978-0-9873285-0-2},
  pages     = {[152] -- [160]},
  year      = {2012},
  language  = {en}
}
@inproceedings{PuetzBaierBrauneretal.2022,
  author    = {P{\"u}tz, Sebastian and Baier, Ralph and Brauner, Philipp and Brillowski, Florian and Dammers, Hannah and Liehner, Luca and Mertens, Alexander and Rodemann, Niklas and Schneider, Sebastian and Schollemann, Alexander and Steuer-Dankert, Linda and Vervier, Luisa and Gries, Thomas and Leicht-Scholten, Carmen and Nagel, Saskia K. and Piller, Frank T. and Schuh, G{\"u}nther and Ziefle, Martina and Nitsch, Verena},
  title     = {An interdisciplinary view on humane interfaces for digital shadows in the internet of production},
  series = {2022 15th International Conference on Human System Interaction (HSI)},
  booktitle = {2022 15th International Conference on Human System Interaction (HSI)},
  publisher = {IEEE},
  isbn      = {978-1-6654-6823-7 (Print)},
  issn      = {2158-2246 (Print)},
  doi       = {10.1109/HSI55341.2022.9869467},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {Digital shadows play a central role for the next generation industrial internet, also known as Internet of Production (IoP). However, prior research has not considered systematically how human actors interact with digital shadows, shaping their potential for success. To address this research gap, we assembled an interdisciplinary team of authors from diverse areas of human-centered research to propose and discuss design and research recommendations for the implementation of industrial user interfaces for digital shadows, as they are currently conceptualized for the IoP. Based on the four use cases of decision support systems, knowledge sharing in global production networks, human-robot collaboration, and monitoring employee workload, we derive recommendations for interface design and enhancing workers' capabilities. This analysis is extended by introducing requirements from the higher-level perspectives of governance and organization.},
  language  = {en}
}
@article{PoettgenEdererAltherretal.2015,
  author    = {P{\"o}ttgen, Philipp and Ederer, Thorsten and Altherr, Lena and Pelz, Peter F.},
  title     = {Developing a control strategy for booster stations under uncertain load},
  series = {Applied Mechanics and Materials},
  volume    = {807},
  journal   = {Applied Mechanics and Materials},
  number    = {807},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  isbn      = {1662-7482},
  doi       = {10.4028/www.scientific.net/AMM.807.241},
  pages     = {241 -- 246},
  year      = {2015},
  abstract  = {Booster stations can fulfill a varying pressure demand with high energy-efficiency, because individual pumps can be deactivated at smaller loads. Although this is a seemingly simple approach, it is not easy to decide precisely when to activate or deactivate pumps. Contemporary activation controls derive the switching points from the current volume flow through the system. However, it is not measured directly for various reasons. Instead, the controller estimates the flow based on other system properties. This causes further uncertainty for the switching decision. In this paper, we present a method to find a robust, yet energy-efficient activation strategy.},
  language  = {en}
}
@article{PoettgenEdererAltherretal.2015,
  author    = {P{\"o}ttgen, Philipp and Ederer, Thorsten and Altherr, Lena and Lorenz, Ulf and Pelz, Peter F.},
  title     = {Examination and optimization of a heating circuit for energy-efficient buildings},
  series = {Energy Technology},
  volume    = {4},
  journal   = {Energy Technology},
  number    = {1},
  publisher = {WILEY-VCH Verlag},
  address   = {Weinheim},
  isbn      = {2194-4296},
  doi       = {10.1002/ente.201500252},
  pages     = {136 -- 144},
  year      = {2015},
  abstract  = {The conference center darmstadtium in Darmstadt is a prominent example of energy efficient buildings. Its heating system consists of different source and consumer circuits connected by a Zortstr{\"o}m reservoir. Our goal was to reduce the energy costs of the system as much as possible. Therefore, we analyzed its supply circuits. The first step towards optimization is a complete examination of the system: 1) Compilation of an object list for the system, 2) collection of the characteristic curves of the components, and 3) measurement of the load profiles of the heat and volume-flow demand. Instead of modifying the system manually and testing the solution by simulation, the second step was the creation of a global optimization program. The objective was to minimize the total energy costs for one year. We compare two different topologies and show opportunities for significant savings.},
  language  = {en}
}
@article{PuppeGiulianoFrantzetal.2018,
  author    = {Puppe, Michael and Giuliano, Stefano and Frantz, Cathy and Uhlig, Ralf and Schumacher, Ralph and Ibraheem, Wagdi and Schmalz, Stefan and Waldmann, Barbara and Guder, Christoph and Peter, Dennis and Schwager, Christian and Teixeira Boura, Cristiano Jos{\´e} and Alexopoulos, Spiros and Spiegel, Michael and Wortmann, J{\"u}rgen and Hinrichs, Matthias and Engelhard, Manfred and Aust, Michael},
  title     = {Techno-economic optimization of molten salt solar tower plants},
  series = {AIP Conference Proceedings art.no. 040033},
  volume    = {2033},
  journal   = {AIP Conference Proceedings art.no. 040033},
  number    = {Issue 1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  doi       = {10.1063/1.5067069},
  year      = {2018},
  abstract  = {In this paper the results of a techno-economic analysis of improved and optimized molten salt solar tower plants (MSSTP plants) are presented. The potential improvements that were analyzed include different receiver designs, different designs of the HTF-system and plant control, increased molten salt temperatures (up to 640°C) and multi-tower systems. Detailed technological and economic models of the solar field, solar receiver and high temperature fluid system (HTF-system) were developed and used to find potential improvements compared to a reference plant based on Solar Two technology and up-to-date cost estimations. The annual yield model calculates the annual outputs and the LCOE of all variants. An improved external tubular receiver and improved HTF-system achieves a significant decrease of LCOE compared to the reference. This is caused by lower receiver cost as well as improvements of the HTF-system and plant operation strategy, significantly reducing the plant own consumption. A novel star receiver shows potential for further cost decrease. The cavity receiver concepts result in higher LCOE due to their high investment cost, despite achieving higher efficiencies. Increased molten salt temperatures seem possible with an adapted, closed loop HTF-system and achieve comparable results to the original improved system (with 565°C) under the given boundary conditions. In this analysis all multi tower systems show lower economic viability compared to single tower systems, caused by high additional cost for piping connections and higher cost of the receivers. REFERENCES},
  language  = {en}
}
@incollection{PuliniGligorevic2009,
  author    = {Pulini, Paola and Gligorevic, Snjezana},
  title     = {WIMAX performance in the airport environment},
  series = {Multi-carrier systems \& solutions 2009. (Lecture notes in electrical engineering ; 41)},
  booktitle = {Multi-carrier systems \& solutions 2009. (Lecture notes in electrical engineering ; 41)},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {978-90-481-2529-6 (Print) ; 978-90-481-2530-2 (Online)},
  pages     = {301 -- 310},
  year      = {2009},
  abstract  = {In this paper, the multicarrier physical layers of WiMAX are evaluated in the context of airport data links. The orthogonal frequency-division multiplexing (OFDM) and orthogonal frequency-division multiple-access (OFDMA) cases are applied to the forward link (FL) and reverse link (RL), respectively. The performance of the so called parking and taxi scenarios is presented for airport communications in C-band. Numerical results show that the proposed scheme brings good performance for both the FL and the RL. For the OFDMA case a structure changing called double-tile is also proposed to improve the system performance.},
  language  = {en}
}
@article{PrumeZalachasLaskewitzetal.2008,
  author    = {Prume, Klaus and Zalachas, Nicolas and Laskewitz, Bernd and Kamlah, Marc},
  title     = {Effective Piezoelectric Coefficients of Ferroelectric Thin Films on Elastic Substrates / Zalachas, Nicolas ; Laskewitz, Bernd ; Kamlah, Marc ; Prume, Klaus ; Lapusta, Yuri ; Tiedke, Stephan},
  series = {Journal of Intelligent Material Systems and Structures. 20 (2008), H. 6},
  journal   = {Journal of Intelligent Material Systems and Structures. 20 (2008), H. 6},
  isbn      = {1045-389X},
  pages     = {683 -- 695},
  year      = {2008},
  language  = {en}
}
@article{PrumeWaserFrankenetal.2000,
  author    = {Prume, Klaus and Waser, Rainer and Franken, Klaus and Maier, Horst R.},
  title     = {Finite-Element Analysis of Ceramic Multilayer Capacitors: Modeling and Electrical Impedance Spectroscopy for a Nondestructive Failure Test / Prume, Klaus ; Waser, Rainer ; Franken, Klaus ; Maier, Horst R. ;},
  series = {Journal of the American Ceramic Society. 83 (2000), H. 5},
  journal   = {Journal of the American Ceramic Society. 83 (2000), H. 5},
  isbn      = {0002-7820},
  pages     = {1153 -- 1159},
  year      = {2000},
  language  = {en}
}
@article{PrumeWaser2000,
  author    = {Prume, Klaus and Waser, Rainer},
  title     = {Finite-element simulation of coupled characteristics of ceramic multilayer capacitors under transient electrical loading / Prume, Klaus ; Waser, Rainer},
  series = {Proceedings of the 2000 12th IEEE International Symposium on Applications of Ferroelectrics. Vol. 2},
  journal   = {Proceedings of the 2000 12th IEEE International Symposium on Applications of Ferroelectrics. Vol. 2},
  pages     = {675 -- 678},
  year      = {2000},
  language  = {en}
}
@article{PrumeTyholdtCalameetal.2007,
  author    = {Prume, Klaus and Tyholdt, F. and Calame, F. and Raeder, H.},
  title     = {Chemically derived seeding layer for {100}-textured PZT thin films / Tyholdt, F. ; Calame, F. ; Prume, K. ; Raeder, H. ; Muralt, P.},
  series = {Journal of Electroceramics. 19 (2007), H. 4},
  journal   = {Journal of Electroceramics. 19 (2007), H. 4},
  isbn      = {1385-3449},
  pages     = {311 -- 314},
  year      = {2007},
  language  = {en}
}
@article{PrumeTiedkeSchmitzetal.2001,
  author    = {Prume, Klaus and Tiedke, S. and Schmitz, T. and Roelofs, A.},
  title     = {Direct hysteresis measurements of single nanosized ferroelectric capacitors contacted with an atomic force microscope / Tiedke, S. ; Schmitz, T. ; Prume, K. ; Roelofs, A. ; Schneller, T. ; Kall, U. ; Waser, R. ; Ganpule, C. S. ; Nagarajan, V. ; Stanishevs},
  series = {Applied Physics Letters. 79 (2001), H. 22},
  journal   = {Applied Physics Letters. 79 (2001), H. 22},
  isbn      = {0003-6951},
  pages     = {3678 -- 3680},
  year      = {2001},
  language  = {en}
}
@article{PrumeRoelofsSchmitzetal.2002,
  author    = {Prume, Klaus and Roelofs, Andreas and Schmitz, Thorsten and Reichenberg, Bernd},
  title     = {Compensation of the Parasitic Capacitance of a Scanning Force Microscope Cantilever Used for Measurements on Ferroelectric Capacitors of Submicron Size by Means of Finite Element Simulations / Prume, Klaus ; Roelofs, Andreas ; Schmitz, Thorsten ; Reichenb},
  series = {Japanese Journal of Applied Physics. 41 (2002), H. 11B},
  journal   = {Japanese Journal of Applied Physics. 41 (2002), H. 11B},
  isbn      = {0021-4922},
  pages     = {7198 -- 7201},
  year      = {2002},
  language  = {en}
}
@article{PrumeReichenbergRoelofsetal.2004,
  author    = {Prume, Klaus and Reichenberg, B. and Roelofs, A. and Waser, R.},
  title     = {In-situ compensation of the parasitic capacitance for nanoscale hysteresis measurements / Schmitz, T. ; Prume, K. ; Reichenberg, B. ; Roelofs, A. ; Waser, R. ; Tiedke, S.},
  series = {Journal of the European Ceramic Society. 24 (2004), H. 6},
  journal   = {Journal of the European Ceramic Society. 24 (2004), H. 6},
  isbn      = {0955-2219},
  pages     = {1145 -- 1147},
  year      = {2004},
  language  = {en}
}
@article{PrumeRaederTyholdtetal.2007,
  author    = {Prume, Klaus and Raeder, H. and Tyholdt, F. and Booij, W. E.},
  title     = {Taking piezoelectric microsystems from the laboratory to production / Raeder, H. ; Tyholdt, F. ; Booij, W. ; Calame, F. ; Ostbo, N. P. ; Bredesen, R. ; Prume, K. ; Rijnders, G. ; Muralt, P.},
  series = {Journal of Electroceramics. 19 (2007), H. 4},
  journal   = {Journal of Electroceramics. 19 (2007), H. 4},
  isbn      = {1385-3449},
  pages     = {357 -- 362},
  year      = {2007},
  language  = {en}
}
@article{PrumePeterRuedigeretal.2005,
  author    = {Prume, Klaus and Peter, F. and R{\"u}diger, A. and Dittmann, R.},
  title     = {Analysis of shape effects on the piezoresponse in ferroelectric nanograins with and without adsorbates / Peter, F. ; R{\"u}diger, A. ; Dittmann, R. ; Waser, R. ; Szot, K. ; Reichenberg, B. ; Prume, K. ;},
  series = {Applied Physics Letters . 87 (2005), H. 8},
  journal   = {Applied Physics Letters . 87 (2005), H. 8},
  isbn      = {0003-6951},
  pages     = {082901 -- 082901-3},
  year      = {2005},
  language  = {en}
}
@article{PrumeMuraltCalameetal.2007,
  author    = {Prume, Klaus and Muralt, Paul and Calame, Florian and Schmitz-Kempen, Thorsten},
  title     = {Extensive electromechanical characterization of PZT thin films for MEMS applications by electrical and mechanical excitation signals / Prume, Klaus ; Muralt, Paul ; Calame, Florian ; Schmitz-Kempen, Thorsten ; Tiedke, Stephan},
  series = {Journal of Electroceramics. 19 (2007), H. 4},
  journal   = {Journal of Electroceramics. 19 (2007), H. 4},
  isbn      = {1385-3449},
  pages     = {407 -- 411},
  year      = {2007},
  language  = {en}
}
@article{PrumeMuraltCalameetal.2007,
  author    = {Prume, Klaus and Muralt, P. and Calame, F. and Schmitz-Kempen, T.},
  title     = {Piezoelectric thin films: evaluation of electrical and electromechanical characteristics for MEMS devices / Prume, K. ; Muralt, P. ; Calame, F. ; Schmitz-Kempen, T. ; Tiedke, S. ;},
  series = {IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control. 54 (2007), H. 1},
  journal   = {IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control. 54 (2007), H. 1},
  isbn      = {0885-3010},
  pages     = {81 -- 14},
  year      = {2007},
  language  = {en}
}
@article{PrumeMeyerWaseretal.2005,
  author    = {Prume, Klaus and Meyer, Ren{\´e} and Waser, Rainer and Schmitz, Torsten},
  title     = {Dynamic leakage current compensation in ferroelectric thin-film capacitor structures / Meyer, Ren{\´e} ; Waser, Rainer ; Prume, Klaus ; Schmitz, Torsten ; Tiedke, Stephan},
  series = {Applied Physics Letters . 86 (2005), H. 14},
  journal   = {Applied Physics Letters . 86 (2005), H. 14},
  isbn      = {0003-6951},
  pages     = {142907-1 -- 142907-3},
  year      = {2005},
  language  = {en}
}
@article{PrumeGerberKuegeleretal.2004,
  author    = {Prume, Klaus and Gerber, Peter and K{\"u}geler, Carsten and Roelofs, Andreas},
  title     = {Simulation and measurements of the piezoelectric properties response (d33) of piezoelectric layered thin film structures influenced by the top-electrode size / Prume, K. ; Gerber, P. ; K{\"u}geler, C. ; Roelofs, A. ; B{\"o}ttger, U. ; Waser, R. ; Schmitz-Kempen,},
  isbn      = {0-7803-8410-5},
  pages     = {7 -- 10},
  year      = {2004},
  language  = {en}
}
@article{PrumeGerberRoelofsetal.2004,
  author    = {Prume, Klaus and Gerber, P. and Roelofs, A. and K{\"u}geler, C.},
  title     = {Effects of the top-electrode size on the piezoelectric properties (d33 and S) of lead zirconate titanate thin films / Gerber, P. ; Roelofs, A. ; K{\"u}geler, C.; B{\"o}ttger, U. ; Waser, R. ; Prume, K. ;},
  series = {Journal of Applied Physics . 96 (2004), H. 5},
  journal   = {Journal of Applied Physics . 96 (2004), H. 5},
  isbn      = {0021-8979},
  pages     = {2800 -- 2804},
  year      = {2004},
  language  = {en}
}
@article{PrumeFrankenMaieretal.2000,
  author    = {Prume, Klaus and Franken, Klaus and Maier, Horst R. and Waser, Rainer},
  title     = {Finite-Element Analysis of Ceramic Multilayer Capacitors: Failure Probability Caused by Wave Soldering and Bending Loads / Franken, Klaus ; Maier, Horst R. ; Prume, Klaus ; Waser, Rainer},
  series = {Journal of the American Ceramic Society. 83 (2000), H. 6},
  journal   = {Journal of the American Ceramic Society. 83 (2000), H. 6},
  isbn      = {0002-7820},
  pages     = {1433 -- 1440},
  year      = {2000},
  language  = {en}
}
@article{PrumeFrankenBoettgeretal.2002,
  author    = {Prume, Klaus and Franken, Klaus and B{\"o}ttger, Ulrich and Waser, Rainer},
  title     = {Modelling and numerical simulation of the electrical, mechanical, and thermal coupled behaviour of Multilayer capacitors (MLCs) / Prume, Klaus ; Franken, Klaus ; B{\"o}ttger, Ulrich ; Waser, Rainer ; Maier, Horst R.},
  series = {Journal of the European Ceramic Society. 22 (2002), H. 8},
  journal   = {Journal of the European Ceramic Society. 22 (2002), H. 8},
  isbn      = {0955-2219},
  pages     = {1285 -- 1296},
  year      = {2002},
  language  = {en}
}
@article{PrumeBooijVogletal.2007,
  author    = {Prume, Klaus and Booij, W. E. and Vogl, A. H. and Wang, D. T.},
  title     = {A simple and powerful analytical model for MEMS piezoelectric multimorphs / Booij, W. E. ; Vogl, A. H. ; Wang, D. T. ; Tyholdt, F. ; Ostbo, N. P. ; Raeder, H. ; Prume, K.},
  series = {Journal of Electroceramics. 19 (2007), H. 4},
  journal   = {Journal of Electroceramics. 19 (2007), H. 4},
  isbn      = {1385-3449},
  pages     = {387 -- 393},
  year      = {2007},
  language  = {en}
}
@article{Prume2007,
  author    = {Prume, Klaus},
  title     = {Electrical and electromechanical characterization of piezoelectric thin films in view of MEMS application / Tiedke, S. ; Prume, K. ; Schmitz-Kempen, T.;},
  pages     = {702},
  year      = {2007},
  language  = {en}
}
@article{ProchnowGebingLadageetal.2011,
  author    = {Prochnow, Nora and Gebing, Tina and Ladage, Kerstin and Krause-Finkeldey, Dorothee and Ourdi, Abessamad El and Bitz, Andreas and Streckert, Joachim and Hansen, Volkert and Dermietzel, Rolf},
  title     = {Electromagnetic field effect or simply stress? Effects of UMTS exposure on hippocampal longterm plasticity in the context of procedure related hormone release},
  series = {PLoS one},
  volume    = {6},
  journal   = {PLoS one},
  number    = {5},
  publisher = {PLOS},
  address   = {San Francisco},
  doi       = {10.1371/journal.pone.0019437},
  pages     = {e19437},
  year      = {2011},
  abstract  = {Harmful effects of electromagnetic fields (EMF) on cognitive and behavioural features of humans and rodents have been controversially discussed and raised persistent concern about adverse effects of EMF on general brain functions. In the present study we applied radio-frequency (RF) signals of the Universal Mobile Telecommunications System (UMTS) to full brain exposed male Wistar rats in order to elaborate putative influences on stress hormone release (corticosteron; CORT and adrenocorticotropic hormone; ACTH) and on hippocampal derived synaptic long-term plasticity (LTP) and depression (LTD) as electrophysiological hallmarks for memory storage and memory consolidation. Exposure was computer controlled providing blind conditions. Nominal brain-averaged specific absorption rates (SAR) as a measure of applied mass-related dissipated RF power were 0, 2, and 10 W/kg over a period of 120 min. Comparison of cage exposed animals revealed, regardless of EMF exposure, significantly increased CORT and ACTH levels which corresponded with generally decreased field potential slopes and amplitudes in hippocampal LTP and LTD. Animals following SAR exposure of 2 W/kg (averaged over the whole brain of 2.3 g tissue mass) did not differ from the sham-exposed group in LTP and LTD experiments. In contrast, a significant reduction in LTP and LTD was observed at the high power rate of SAR (10 W/kg). The results demonstrate that a rate of 2 W/kg displays no adverse impact on LTP and LTD, while 10 W/kg leads to significant effects on the electrophysiological parameters, which can be clearly distinguished from the stress derived background. Our findings suggest that UMTS exposure with SAR in the range of 2 W/kg is not harmful to critical markers for memory storage and memory consolidation, however, an influence of UMTS at high energy absorption rates (10 W/kg) cannot be excluded.},
  language  = {en}
}
@article{ProbstBehbahaniBorrmannetal.2010,
  author    = {Probst, M. and Behbahani, Mehdi and Borrmann, E. and Elgeti, S. and Nicolai, M. and Behr, M.},
  title     = {Hemodynamic Modeling for Numerical Analysis and Design of Medical Devices},
  year      = {2010},
  language  = {en}
}
@article{PrielmeierWoznyjLuedemann1984,
  author    = {Prielmeier, Franz and Woznyj, M. and L{\"u}demann, H.-D.},
  title     = {Pressure Dependence of the Melting and Self Diffusion in 2,2-Dimethylpropane, 2,2-Dimethylpropionitrile, and 2-Methylpropanol-2 / M. Woznyj, F. X. Prielmeier, H.-D. L{\"u}demann},
  series = {Zeitschrift f{\"u}r Naturforschung A, Journal of Physical Sciences. 39 (1984)},
  journal   = {Zeitschrift f{\"u}r Naturforschung A, Journal of Physical Sciences. 39 (1984)},
  isbn      = {0932-0784},
  pages     = {800},
  year      = {1984},
  language  = {en}
}
@article{PrielmeierWickNagatomoetal.1995,
  author    = {Prielmeier, Franz and Wick, Markus and Nagatomo, Yasushi and Frahm, Jens},
  title     = {Alteration of Intracellular Metabolite Diffusion in Rat Brain In Vivo During Ischemia and Reperfusion / Markus Wick, Yasushi Nagatomo, Franz Prielmeier, Jens Frahm},
  series = {Stroke. 26 (1995), H. 10},
  journal   = {Stroke. 26 (1995), H. 10},
  isbn      = {0039-2499},
  pages     = {1930 -- 1934},
  year      = {1995},
  language  = {en}
}
@article{PrielmeierSpeedyVardagetal.1989,
  author    = {Prielmeier, Franz and Speedy, R. J. and Vardag, T. and Lang, E. W.},
  title     = {Diffusion in simple fluids / R. J. Speedy; F. X. Prielmeier; T. Vardag; E. W. Lang; H.-D. L{\"u}demann},
  series = {Molecular Physics. 66 (1989), H. 3},
  journal   = {Molecular Physics. 66 (1989), H. 3},
  isbn      = {0026-8976},
  pages     = {577 -- 590},
  year      = {1989},
  language  = {en}
}
@article{PrielmeierSpeedyLuedemann1987,
  author    = {Prielmeier, Franz and Speedy, R. J. and L{\"u}demann, H.-D.},
  title     = {High Pressure NMR Self-Diffusion Studies on Supercooled Water},
  series = {High Pressure Science and Technology Proceeding XI AIRAPT, Kiew. 1},
  journal   = {High Pressure Science and Technology Proceeding XI AIRAPT, Kiew. 1},
  pages     = {75},
  year      = {1987},
  language  = {en}
}
@article{PrielmeierRadkowitschLangetal.1986,
  author    = {Prielmeier, Franz and Radkowitsch, H. and Lang, E. W. and L{\"u}demann, H.-D.},
  title     = {Density dependence of the molecular dynamics of fluid CH3F and CF3H studied by NMR / H. Radkowitsch, F. X. Prielmeier, E. W. Lang and H.-D. L{\"u}demann},
  series = {Physica B+C. 139-140 (1986)},
  journal   = {Physica B+C. 139-140 (1986)},
  isbn      = {0921-4526},
  pages     = {96 -- 99},
  year      = {1986},
  language  = {en}
}
@article{PrielmeierNagatomoWicketal.1995,
  author    = {Prielmeier, Franz and Nagatomo, Yasushi and Wick, Markus and Frahm, Jens},
  title     = {Dynamic monitoring of cerebral metabolites during and after transient global ischemia in rats by quantitative proton NMR spectroscopy in vivo / Yasushi Nagatomo, Markus Wick, Franz Prielmeier, Jens Frahm},
  series = {NMR in Biomedicine. 8 (1995), H. 6},
  journal   = {NMR in Biomedicine. 8 (1995), H. 6},
  isbn      = {1099-1492},
  pages     = {265 -- 270},
  year      = {1995},
  language  = {en}
}
@article{PrielmeierNagatomoFrahm1994,
  author    = {Prielmeier, Franz and Nagatomo, Yasushi and Frahm, Jens},
  title     = {Cerebral blood oxygenation in rat brain during hypoxic hypoxia. Quantitative MRI of effective transverse relaxation rates},
  series = {Magnetic Resonance in Medicine. 31 (1994), H. 6},
  journal   = {Magnetic Resonance in Medicine. 31 (1994), H. 6},
  isbn      = {0740-3194},
  pages     = {678 -- 681},
  year      = {1994},
  language  = {en}
}
@article{PrielmeierMerboldtHanickeetal.1993,
  author    = {Prielmeier, Franz and Merboldt, K. D. and Hanicke, W. and Frahm, J.},
  title     = {Dynamic high-resolution MR imaging of brain deoxygenation during transient anoxia in the anesthetized rat},
  series = {Journal of cerebral blood flow and metabolism. 13 (1993), H. 5},
  journal   = {Journal of cerebral blood flow and metabolism. 13 (1993), H. 5},
  isbn      = {0271-678X},
  pages     = {889 -- 894},
  year      = {1993},
  language  = {en}
}
@article{PrielmeierLuedemann1986,
  author    = {Prielmeier, Franz and L{\"u}demann, H.-D.},
  title     = {Self diffusion in compressed liquid chloromethane, dichloromethane and trichloromethane / F. X. Prielmeier; H.-D. L{\"u}demann},
  series = {Molecular Physics. 58 (1986), H. 3},
  journal   = {Molecular Physics. 58 (1986), H. 3},
  isbn      = {0026-8976},
  pages     = {593 -- 604},
  year      = {1986},
  language  = {en}
}
@article{PrielmeierLangSpeedyetal.1988,
  author    = {Prielmeier, Franz and Lang, E. W. and Speedy, R. J. and L{\"u}demann, H.-D.},
  title     = {The pressure Dependence of Self Diffusion in Supercooled Light and Heavy Water / F.X. Prielmeier, E .W. Lang, R. J. Speedy, H.-D. L{\"u}demann},
  series = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 92 (1988)},
  journal   = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 92 (1988)},
  isbn      = {0005-9021},
  pages     = {1111},
  year      = {1988},
  language  = {en}
}
@article{PrielmeierLangSpeedyetal.1987,
  author    = {Prielmeier, Franz and Lang, E. W. and Speedy, R. J. and L{\"u}demann, H.-D.},
  title     = {Diffusion in supercooled water to 300 MPa},
  series = {Physical Review Letters. 59 (1987), H. 10},
  journal   = {Physical Review Letters. 59 (1987), H. 10},
  isbn      = {0031-9007},
  pages     = {1128 -- 1131},
  year      = {1987},
  language  = {en}
}
@article{PrielmeierLangRadkowitschetal.1987,
  author    = {Prielmeier, Franz and Lang, E. W. and Radkowitsch, H. and L{\"u}demann, H.-D.},
  title     = {High Pressure NMR Study of the Molecular Dynamics of Liquid methyl fluoride and deutero-methyl fluoride / Lang, E. W. ; Prielmeier, F. X. ; Radkowitsch, H. ; L{\"u}demann, H. D.},
  series = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 91 (1987), H. 10},
  journal   = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 91 (1987), H. 10},
  isbn      = {0005-9021},
  pages     = {1017 -- 1025},
  year      = {1987},
  language  = {en}
}
@article{PrielmeierLangRadkowitschetal.1987,
  author    = {Prielmeier, Franz and Lang, E. W. and Radkowitsch, H. and L{\"u}demann, H. D.},
  title     = {High Pressure NMR Study of the Molecular Dynamics of Liquid fluoroform and deutero-fluoroform / Lang, E. W. ; Prielmeier, F. X. ; Radkowitsch, H. ; L{\"u}demann, H. D.},
  series = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 91 (1987), H. 10},
  journal   = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 91 (1987), H. 10},
  isbn      = {0005-9021},
  pages     = {1025 -- 1033},
  year      = {1987},
  language  = {en}
}
@article{PrielmeierLangLuedemann1984,
  author    = {Prielmeier, Franz and Lang, E. W. and L{\"u}demann, H.-D.},
  title     = {Pressure dependence of the self-diffusion in liquid trifluoromethane / F. X. Prielmeier; E. W. Lang; H.-D. L{\"u}demann},
  series = {Molecular Physics. 52 (1984), H. 5},
  journal   = {Molecular Physics. 52 (1984), H. 5},
  isbn      = {0026-8976},
  pages     = {1105 -- 1113},
  year      = {1984},
  language  = {en}
}
@article{PrielmeierLang1988,
  author    = {Prielmeier, Franz and Lang, E. W.},
  title     = {Multinuclear Spin-Lattice Relaxation Time Studies of Supercooled Aqueous LiCl-Solutions / E .W. Lang, F. X. Prielmeier},
  series = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 92 (1988)},
  journal   = {Berichte der Bunsen-Gesellschaft f{\"u}r Physikalische Chemie. 92 (1988)},
  isbn      = {0005-9021},
  pages     = {717},
  year      = {1988},
  language  = {en}
}
@article{PrielmeierHoerstermannGyngelletal.1992,
  author    = {Prielmeier, Franz and H{\"o}rstermann, D. and Gyngell, M. L. and Merboldt, K.-D.},
  title     = {Localized Proton MRS of Acute and Chronic Gyperglycemia in Rat Brain in vivo / D. H{\"o}rstermann, F. Prielmeier , M. L. Gyngell, K.-D. Merboldt, W. H{\"a}nicke, J. Frahm},
  series = {Book of Abstracts, SMRM, 11th Annual Meeting Berlin},
  journal   = {Book of Abstracts, SMRM, 11th Annual Meeting Berlin},
  pages     = {2740},
  year      = {1992},
  language  = {en}
}
@incollection{PriedeFerrein2013,
  author    = {Priede, Gareth and Ferrein, Alexander},
  title     = {Towards passive walking for the fully-actuated biped robot Nao},
  series = {Emerging trends in computing, informatics, systems sciences, and engineering. (Lecture notes in electrical engineering : vol. 151)},
  booktitle = {Emerging trends in computing, informatics, systems sciences, and engineering. (Lecture notes in electrical engineering : vol. 151)},
  publisher = {Springer},
  address   = {New York, NY},
  isbn      = {978-1-4614-3557-0 ; 978-1-4614-3558-7},
  doi       = {10.1007/978-1-4614-3558-7_18},
  pages     = {225 -- 236},
  year      = {2013},
  abstract  = {Many biped robots deploy a form of gait that follows the zero moment point (ZMP) approach, that is, the robot is in a stable position at any point in time. This requires the robot to be fully actuated. While very stable, the draw-backs of this approach are a fairly slow gait and high energy consumption. An alternative approach is the so-called passive-dynamic walking, where the gait makes use of the inertia and dynamic stability of the robot. In this paper we describe our ongoing work of combining the principles of passive-dynamic walking on the fully-actuated biped robot Nao, which is also deployed for robotic soccer applications. We present a simple controller that allows the robot to stably rock sidewards, showing a closed limit-cycle. We discuss first results of superimposing a forward motion on the sidewards motion. Based on this we expect to endow the Nao with a fast, robust, and stable passive-dynamic walk on the fully-actuated Nao in the future.},
  language  = {en}
}
@inproceedings{PrickingGebsFleischhakeretal.2015,
  author    = {Pricking, Sebastian and Gebs, Raphael and Fleischhaker, Robert and Kleinbauer, Jochen and Budnicki, Aleksander and Sutter, Dirk and Killi, Alexander and Weiler, Sascha and Mielke, M. and Beaudou, B. and Debord, B. and Gerome, F. and Benabid, F.},
  title     = {Hollow core fiber delivery of sub-ps pulses from a TruMicro 5000 Femto edition thin disk amplifier},
  series = {High-power laser materials processing: Lasers, beam delivery, diagnostics, and applications IV : 7 Februar 2015, San Francisco, USA. - (SPIE proceedings series ; 9356)},
  booktitle = {High-power laser materials processing: Lasers, beam delivery, diagnostics, and applications IV : 7 Februar 2015, San Francisco, USA. - (SPIE proceedings series ; 9356)},
  editor    = {Dorsch, Friedhelm},
  publisher = {SPIE, International Society for Optical Engineering},
  organization    = {The international society for optical engineering, SPIE <2, 2015, San Francisco, CA>},
  isbn      = {978-162841446-2},
  issn      = {0277-786X},
  doi       = {10.1117/12.2079289},
  pages     = {935602},
  year      = {2015},
  language  = {en}
}
@article{PresslerEsefeldScherretal.2010,
  author    = {Pressler, Axel and Esefeld, Katrin and Scherr, Johannes and Ali, Mohammad and Hanssen, Henner and Kotliar, Konstantin and Lanzl, Ines and Halle, Martin and Kaemmerer, Harald and Schmidt-Trucks{\"a}ss, Arno and Hager, Alfred},
  title     = {Structural alterations of retinal arterioles in adults late after repair of aortic isthmic coarctation},
  series = {The American Journal of Cardiology},
  volume    = {105},
  journal   = {The American Journal of Cardiology},
  number    = {5},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0002-9149},
  doi       = {10.1016/j.amjcard.2009.10.070},
  pages     = {740 -- 744},
  year      = {2010},
  abstract  = {Patients after coarctation repair still have an increased risk of cardiovascular or cerebrovascular events. This has been explained by the persisting hypertension and alterations in the peripheral vessels. However, involvement of the central vessels such as the retinal arteries is virtually unknown. A total of 34 patients after coarctation repair (22 men and 12 women; 23 to 58 years old, age range 0 to 32 years at surgical repair) and 34 nonhypertensive controls underwent structural and functional retinal vessel analysis. Using structural analysis, the vessel diameters were measured. Using functional analysis, the endothelium-dependent vessel dilation in response to flicker light stimulation was assessed. In the patients after coarctation repair, the retinal arteriolar diameter was significantly reduced compared to that of the controls (median 182 μm, first to third quartile 171 to 197; vs 197 μm, first to third quartile 193 to 206; p <0.001). These findings were independent of the peripheral blood pressure and age at intervention. No differences were found for venules. The functional analysis findings were not different between the patients and controls (maximum dilation 3.5\%, first to third quartile 2.1\% to 4.5\% vs 3.6\%, first to third quartile 2.2\% to 4.3\%; p = 0.81), indicating preserved autoregulative mechanisms. In conclusion, the retinal artery diameter is reduced in patients after coarctation repair, independent of their current blood pressure level and age at intervention. As a structural marker of chronic vessel damage associated with past, current, or future hypertension, retinal arteriolar narrowing has been linked to stroke incidence. These results indicate an involvement of cerebral microcirculation in aortic coarctation, despite timely repair, and might contribute to explain the increased rate of cerebrovascular events in such patients.},
  language  = {en}
}
@article{PreissLinderWendtetal.2011,
  author    = {Preiß, C. and Linder, Peter and Wendt, K. and Krystek, M. and Digel, Ilya and Gossmann, Matthias and Temiz Artmann, Ayseg{\"u}l and Porst, Dariusz and Kayser, Peter and Bassam, Rasha and Artmann, Gerhard},
  title     = {Engineering technology for plant physiology and plant stress research},
  year      = {2011},
  abstract  = {Plant physiology and plant stress: Plant physiology will be much more important for human mankind because of yield and cultivation limits of crops determined by their resistance to stress. To assess and counteract various stress factors it is necessary to conduct plant research to gain information and results on plant physiology.},
  subject      = {Pflanzenphysiologie},
  language  = {en}
}
@article{PourshahidiEngelmannOffenhaeusseretal.2022,
  author    = {Pourshahidi, Ali Mohammad and Engelmann, Ulrich M. and Offenh{\"a}usser, Andreas and Krause, Hans-Joachim},
  title     = {Resolving ambiguities in core size determination of magnetic nanoparticles from magnetic frequency mixing data},
  series = {Journal of Magnetism and Magnetic Materials},
  volume    = {563},
  journal   = {Journal of Magnetism and Magnetic Materials},
  number    = {In progress, Art. No. 169969},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0304-8853},
  doi       = {10.1016/j.jmmm.2022.169969},
  year      = {2022},
  abstract  = {Frequency mixing magnetic detection (FMMD) has been widely utilized as a measurement technique in magnetic immunoassays. It can also be used for the characterization and distinction (also known as "colourization") of different types of magnetic nanoparticles (MNPs) based on their core sizes. In a previous work, it was shown that the large particles contribute most of the FMMD signal. This leads to ambiguities in core size determination from fitting since the contribution of the small-sized particles is almost undetectable among the strong responses from the large ones. In this work, we report on how this ambiguity can be overcome by modelling the signal intensity using the Langevin model in thermodynamic equilibrium including a lognormal core size distribution fL(dc,d0,σ) fitted to experimentally measured FMMD data of immobilized MNPs. For each given median diameter d0, an ambiguous amount of best-fitting pairs of parameters distribution width σ and number of particles Np with R2 > 0.99 are extracted. By determining the samples' total iron mass, mFe, with inductively coupled plasma optical emission spectrometry (ICP-OES), we are then able to identify the one specific best-fitting pair (σ, Np) one uniquely. With this additional externally measured parameter, we resolved the ambiguity in core size distribution and determined the parameters (d0, σ, Np) directly from FMMD measurements, allowing precise MNPs sample characterization.},
  language  = {en}
}
@article{PourshahidiAchtsnichtOffenhaeusseretal.2022,
  author    = {Pourshahidi, Ali Mohammad and Achtsnicht, Stefan and Offenh{\"a}usser, Andreas and Krause, Hans-Joachim},
  title     = {Frequency Mixing Magnetic Detection Setup Employing Permanent Ring Magnets as a Static Offset Field Source},
  series = {Sensors},
  volume    = {22},
  journal   = {Sensors},
  number    = {22},
  editor    = {Offenh{\"a}usser, Andreas},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s22228776},
  pages     = {12 Seiten},
  year      = {2022},
  abstract  = {Frequency mixing magnetic detection (FMMD) has been explored for its applications in fields of magnetic biosensing, multiplex detection of magnetic nanoparticles (MNP) and the determination of core size distribution of MNP samples. Such applications rely on the application of a static offset magnetic field, which is generated traditionally with an electromagnet. Such a setup requires a current source, as well as passive or active cooling strategies, which directly sets a limitation based on the portability aspect that is desired for point of care (POC) monitoring applications. In this work, a measurement head is introduced that involves the utilization of two ring-shaped permanent magnets to generate a static offset magnetic field. A steel cylinder in the ring bores homogenizes the field. By variation of the distance between the ring magnets and of the thickness of the steel cylinder, the magnitude of the magnetic field at the sample position can be adjusted. Furthermore, the measurement setup is compared to the electromagnet offset module based on measured signals and temperature behavior.},
  language  = {en}
}
@article{PourshahidiAchtsnichtNambipareecheeetal.2021,
  author    = {Pourshahidi, Ali Mohammad and Achtsnicht, Stefan and Nambipareechee, Mrinal Murali and Offenh{\"a}usser, Andreas and Krause, Hans-Joachim},
  title     = {Multiplex detection of magnetic beads using offset field dependent frequency mixing magnetic detection},
  series = {Sensors},
  volume    = {21},
  journal   = {Sensors},
  number    = {17},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s21175859},
  pages     = {16 Seiten},
  year      = {2021},
  abstract  = {Magnetic immunoassays employing Frequency Mixing Magnetic Detection (FMMD) have recently become increasingly popular for quantitative detection of various analytes. Simultaneous analysis of a sample for two or more targets is desirable in order to reduce the sample amount, save consumables, and save time. We show that different types of magnetic beads can be distinguished according to their frequency mixing response to a two-frequency magnetic excitation at different static magnetic offset fields. We recorded the offset field dependent FMMD response of two different particle types at frequencies ƒ₁ + n⋅ƒ₂, n = 1, 2, 3, 4 with ƒ₁ = 30.8 kHz and ƒ₂ = 63 Hz. Their signals were clearly distinguishable by the locations of the extremes and zeros of their responses. Binary mixtures of the two particle types were prepared with different mixing ratios. The mixture samples were analyzed by determining the best linear combination of the two pure constituents that best resembled the measured signals of the mixtures. Using a quadratic programming algorithm, the mixing ratios could be determined with an accuracy of greater than 14\%. If each particle type is functionalized with a different antibody, multiplex detection of two different analytes becomes feasible.},
  language  = {en}
}