@article{BaroudWuBohneretal.2003,
  author    = {Baroud, G. and Wu, J.Z. and Bohner, M and Sponagel, Stefan and Steffen, T.},
  title     = {How to determine the permeability for cement infiltration into osteoporotic cancellous bone},
  series = {Medical Engineering \& Physics. 25 (2003), H. 4},
  journal   = {Medical Engineering \& Physics. 25 (2003), H. 4},
  issn      = {1350-4533},
  pages     = {283 -- 288},
  year      = {2003},
  abstract  = {Cement augmentation is an emerging surgical procedure in which bone cement is used to infiltrate and reinforce osteoporotic vertebrae. Although this infiltration procedure has been widely applied, it is performed empirically and little is known about the flow characteristics of cement during the injection process. We present a theoretical and experimental approach to investigate the intertrabecular bone permeability during the infiltration procedure. The cement permeability was considered to be dependent on time, bone porosity, and cement viscosity in our analysis. In order to determine the time-dependent permeability, ten cancellous bone cores were harvested from osteoporotic vertebrae, infiltrated with acrylic cement at a constant flow rate, and the pressure drop across the cores during the infiltration was measured. The viscosity dependence of the permeability was determined based on published experimental data. The theoretical model for the permeability as a function of bone porosity and time was then fit to the testing data. Our findings suggest that the intertrabecular bone permeability depends strongly on time. For instance, the initial permeability (60.89 mm4/N.s) reduced to approximately 63\% of its original value within 18 seconds. This study is the first to analyze cement flow through osteoporotic bone. The theoretical and experimental models provided in this paper are generic. Thus, they can be used to systematically study and optimize the infiltration process for clinical practice.},
  subject      = {Osteoporose},
  language  = {en}
}
@article{EggertKling2023,
  author    = {Eggert, Mathias and Kling, Rene},
  title     = {How to distribute charging requests of electronic vehicles? A reservation-based approach},
  series = {International Journal of Intelligent Transportation Systems Research},
  volume    = {21},
  journal   = {International Journal of Intelligent Transportation Systems Research},
  number    = {2023},
  publisher = {Springer},
  address   = {Berlin, Heidelberg, New York},
  issn      = {1868-8659},
  doi       = {10.1007/s13177-023-00367-z},
  pages     = {437 -- 460},
  year      = {2023},
  abstract  = {The number of electronic vehicles increase steadily while the space for extending the charging infrastructure is limited. In particular in urban areas, where parking spaces in attractive areas are famous, opportunities to setup new charging stations is very limited. This leads to an overload of some very attractive charging stations and an underutilization of less attractive ones. Against this background, the paper at hand presents the design of an e-vehicle reservation system that aims at distributing the utilization of the charging infrastructure, particularly in urban areas. By applying a design science approach, the requirements for a reservation-based utilization approach are elicited and a model for a suitable distribution approach and its instantiation are developed. The artefact is evaluated by simulating the distribution effects based on data of real charging station utilizations.},
  language  = {en}
}
@article{KlettkeHomburgGell2015,
  author    = {Klettke, Tanja and Homburg, Carsten and Gell, Sebastian},
  title     = {How to measure analyst forecast effort},
  series = {European Accounting Review},
  volume    = {24},
  journal   = {European Accounting Review},
  number    = {1},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {0963-8180},
  doi       = {10.1080/09638180.2014.909291},
  pages     = {129 -- 146},
  year      = {2015},
  abstract  = {We introduce a new way to measure the forecast effort that analysts devote to their earnings forecasts by measuring the analyst's general effort for all covered firms. While the commonly applied effort measure is based on analyst behaviour for one firm, our measure considers analyst behaviour for all covered firms. Our general effort measure captures additional information about analyst effort and thus can identify accurate forecasts. We emphasise the importance of investigating analyst behaviour in a larger context and argue that analysts who generally devote substantial forecast effort are also likely to devote substantial effort to a specific firm, even if this effort might not be captured by a firm-specific measure. Empirical results reveal that analysts who devote higher general forecast effort issue more accurate forecasts. Additional investigations show that analysts' career prospects improve with higher general forecast effort. Our measure improves on existing methods as it has higher explanatory power regarding differences in forecast accuracy than the commonly applied effort measure. Additionally, it can address research questions that cannot be examined with a firm-specific measure. It provides a simple but comprehensive way to identify accurate analysts.},
  language  = {en}
}
@article{DotzauerPfeifferLaueretal.2019,
  author    = {Dotzauer, Martin and Pfeiffer, Diana and Lauer, Markus and Pohl, Marcel and Mauky, Eric and B{\"a}r, Katharina and Sonnleitner, Matthias and Z{\"o}rner, Wilfried and Hudde, Jessica and Schwarz, Bj{\"o}rn and Faßauer, Burkhardt and Dahmen, Markus and Rieke, Christian and Herbert, Johannes and Thr{\"a}n, Daniela},
  title     = {How to measure flexibility - Performance indicators for demand driven power generation from biogas plants},
  series = {Renewable Energy},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2018.10.021},
  pages     = {135 -- 146},
  year      = {2019},
  language  = {en}
}
@article{GoergensGreubelMoosdorf2013,
  author    = {G{\"o}rgens, Stefan and Greubel, Steffen and Moosdorf, Andreas},
  title     = {How to mobilize 20,000 people: Perspectives on retail and consumer goods},
  pages     = {52 -- 58},
  year      = {2013},
  language  = {en}
}
@article{SchubaReichlHoff1997,
  author    = {Schuba, Marko and Reichl, Peter and Hoff, Simon},
  title     = {How to Model Complex Periodic Traffic with TES / Reichl, Peter ; Schuba, Marko ; Hoff, Simon},
  series = {Proc. of 13th United Kingdom Workshop on Performance Engineering, Edinburgh, UK, July 1997},
  journal   = {Proc. of 13th United Kingdom Workshop on Performance Engineering, Edinburgh, UK, July 1997},
  pages     = {17/1 -- 17/11},
  year      = {1997},
  language  = {en}
}
@article{SchubaReichl1996,
  author    = {Schuba, Marko and Reichl, Peter},
  title     = {How to Place Connectionless Servers in ATM Networks / Schuba, Marko ; Reichl, Peter},
  series = {Proc. of Fourth IFIP Workshop on Performance Modelling and Evaluation of ATM Networks},
  journal   = {Proc. of Fourth IFIP Workshop on Performance Modelling and Evaluation of ATM Networks},
  pages     = {09/1 -- 09/10},
  year      = {1996},
  language  = {en}
}
@article{RichterBraunsteinWinnardetal.2017,
  author    = {Richter, Charlotte and Braunstein, Bjoern and Winnard, Andrew and Nasser, Mona and Weber, T.},
  title     = {Human Biomechanical and Cardiopulmonary Responses to Partial Gravity - A Systematic Review},
  series = {Frontiers in physiology},
  journal   = {Frontiers in physiology},
  number    = {8, article 583},
  doi       = {10.3389/fphys.2017.00583},
  pages     = {22 Seiten},
  year      = {2017},
  language  = {en}
}
@article{RossPlummerRodeetal.2010,
  author    = {Ross, Jillian and Plummer, Simon M. and Rode, Anja and Scheer, Nico and Bower, Conrad C. and Vogel, Ortwin and Henderson, Colin J. and Wolf, C. Roland and Elcombe, Clifford R.},
  title     = {Human constitutive androstane receptor (CAR) and pregnane X receptor (PXR) support the hypertrophic but not the hyperplastic response to the murine nongenotoxic hepatocarcinogens phenobarbital and chlordane in vivo},
  series = {Toxicological Sciences},
  volume    = {116},
  journal   = {Toxicological Sciences},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1096-0929},
  doi       = {10.1093/toxsci/kfq118},
  pages     = {452 -- 466},
  year      = {2010},
  abstract  = {Mouse nongenotoxic hepatocarcinogens phenobarbital (PB) and chlordane induce hepatomegaly characterized by hypertrophy and hyperplasia. Increased cell proliferation is implicated in the mechanism of tumor induction. The relevance of these tumors to human health is unclear. The xenoreceptors, constitutive androstane receptors (CARs), and pregnane X receptor (PXR) play key roles in these processes. Novel "humanized" and knockout models for both receptors were developed to investigate potential species differences in hepatomegaly. The effects of PB (80 mg/kg/4 days) and chlordane (10 mg/kg/4 days) were investigated in double humanized PXR and CAR (huPXR/huCAR), double knockout PXR and CAR (PXRKO/CARKO), and wild-type (WT) C57BL/6J mice. In WT mice, both compounds caused increased liver weight, hepatocellular hypertrophy, and cell proliferation. Both compounds caused alterations to a number of cell cycle genes consistent with induction of cell proliferation in WT mice. However, these gene expression changes did not occur in PXRKO/CARKO or huPXR/huCAR mice. Liver hypertrophy without hyperplasia was demonstrated in the huPXR/huCAR animals in response to both compounds. Induction of the CAR and PXR target genes, Cyp2b10 and Cyp3a11, was observed in both WT and huPXR/huCAR mouse lines following treatment with PB or chlordane. In the PXRKO/CARKO mice, neither liver growth nor induction of Cyp2b10 and Cyp3a11 was seen following PB or chlordane treatment, indicating that these effects are CAR/PXR dependent. These data suggest that the human receptors are able to support the chemically induced hypertrophic responses but not the hyperplastic (cell proliferation) responses. At this time, we cannot be certain that hCAR and hPXR when expressed in the mouse can function exactly as the genes do when they are expressed in human cells. However, all parameters investigated to date suggest that much of their functionality is maintained.},
  language  = {en}
}
@article{WhiteheadOehlschlaegerAlmajhdietal.2014,
  author    = {Whitehead, Mark and {\"O}hlschl{\"a}ger, Peter and Almajhdi, Fahad N. and Alloza, Leonor and Marz{\´a}bal, Pablo and Meyers, Ann E. and Hitzeroth, Inga I. and Rybicki, Edward P.},
  title     = {Human papillomavirus (HPV) type 16 E7 protein bodies cause tumour regression in mice},
  series = {BMC cancer},
  journal   = {BMC cancer},
  number    = {14:367},
  publisher = {BioMed Central},
  address   = {London},
  issn      = {1471-2407},
  doi       = {10.1186/1471-2407-14-367},
  pages     = {1 -- 15},
  year      = {2014},
  language  = {en}
}
@article{OehlschlaegerOsenDelletal.2003,
  author    = {{\"O}hlschl{\"a}ger, Peter and Osen, Wolfram and Dell, Kerstin and Faath, Stefan},
  title     = {Human papillomavirus type 16 L1 capsomeres induce L1-specific cytotoxic T lymphocytes and tumor regression in C57BL/6 mice / {\"O}hlschl{\"a}ger, Peter ; Osen, Wolfram ; Dell, Kerstin ; Faath, Stefan ; Garcea Robert L: ; Jochmus, Ingrid ; M{\"u}ller, Martin, Pawlita,},
  series = {Journal of Virology. 77 (2003), H. 8},
  journal   = {Journal of Virology. 77 (2003), H. 8},
  isbn      = {1098-5514},
  pages     = {4635 -- 4645},
  year      = {2003},
  language  = {en}
}
@article{DanhoNaithaniSasakietal.1980,
  author    = {Danho, Waleed and Naithani, Vinod K. and Sasaki, Andr{\´e} N. and F{\"o}hles, Joseph and Berndt, Heinz and B{\"u}llesbach, Erika E. and Zahn, H.},
  title     = {Human proinsulin, VII : synthesis of two protected peptides corresponding to the sequences 1—45 and 46—86 of the prohormone},
  series = {Hoppe-Seyler's Zeitschrift f{\"u}r physiologische Chemie},
  volume    = {361},
  journal   = {Hoppe-Seyler's Zeitschrift f{\"u}r physiologische Chemie},
  number    = {1},
  issn      = {1437-4315},
  doi       = {10.1515/bchm2.1980.361.1.857},
  pages     = {857 -- 863},
  year      = {1980},
  language  = {en}
}
@article{UlmerBraunChengetal.2020,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Human-Centered Gamification Framework for Manufacturing Systems},
  series = {Procedia CIRP},
  volume    = {93},
  journal   = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2020.04.076},
  pages     = {670 -- 675},
  year      = {2020},
  abstract  = {While bringing new opportunities, the Industry 4.0 movement also imposes new challenges to the manufacturing industry and all its stakeholders. In this competitive environment, a skilled and engaged workforce is a key to success. Gamification can generate valuable feedbacks for improving employees' engagement and performance. Currently, Gamification in workspaces focuses on computer-based assignments and training, while tasks that require manual labor are rarely considered. This research provides an overview of Enterprise Gamification approaches and evaluates the challenges. Based on that, a skill-based Gamification framework for manual tasks is proposed, and a case study in the Industry 4.0 model factory is shown.},
  language  = {en}
}
@article{FerreinSiebelSteinbauer2010,
  author    = {Ferrein, Alexander and Siebel, Nils T. and Steinbauer, Gerald},
  title     = {Hybrid control for autonomous systems — Integrating learning, deliberation and reactive control},
  series = {Robotics and Autonomous Systems},
  volume    = {58},
  journal   = {Robotics and Autonomous Systems},
  number    = {9},
  isbn      = {0921-8890},
  pages     = {1037 -- 1038},
  year      = {2010},
  language  = {en}
}
@article{MoraisSilvaDantasetal.2019,
  author    = {Morais, Paulo V. and Silva, Anielle C. A. and Dantas, Noelio O. and Sch{\"o}ning, Michael Josef and Siqueira, Jos{\´e} R., Jr.},
  title     = {Hybrid Layer-by-Layer Film of Polyelectrolytes-Embedded Catalytic CoFe2O4 Nanocrystals as Sensing Units in Capacitive Electrolyte-Insulator-Semiconductor Devices},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {216},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {1900044},
  publisher = {Wiley},
  address   = {Weinheim},
  doi       = {10.1002/pssa.201900044},
  pages     = {1 -- 9},
  year      = {2019},
  language  = {en}
}
@article{FoersterLachenmannKastalskyetal.1998,
  author    = {F{\"o}rster, Arnold and Lachenmann, S. G. and Kastalsky, A. and Uhlisch, D.},
  title     = {Hybrid superconductor/semiconductor step junction with three terminals. Lachenmann, S. G.; Kastalsky, A.; F{\"o}rster A.; Uhlisch, D.; Neurohr, K.; Sch{\"a}pers, Th.},
  series = {Journal of Applied Physics. 83 (1998), H. 12},
  journal   = {Journal of Applied Physics. 83 (1998), H. 12},
  isbn      = {1089-7550},
  pages     = {8077 -- 8079},
  year      = {1998},
  language  = {en}
}
@article{HagemannGeittnerLydtinetal.1988,
  author    = {Hagemann, Hans-J{\"u}rgen and Geittner, P. and Lydtin, H. and Warnier, J.},
  title     = {Hybrid technology for large SM-fiber preforms. Geittner, P.; Hagemann, H. J.; Lydtin, H.; Warnier, J.},
  series = {Journal of Lightwave Technology (J-LT) / Institute of Electrical and Electronics Engineers (IEEE). 6 (1988), H. 10},
  journal   = {Journal of Lightwave Technology (J-LT) / Institute of Electrical and Electronics Engineers (IEEE). 6 (1988), H. 10},
  isbn      = {0733-8724},
  pages     = {1451 -- 1454},
  year      = {1988},
  language  = {en}
}
@article{ErpicumCrookstonBombardellietal.2021,
  author    = {Erpicum, Sebastien and Crookston, Brian M. and Bombardelli, Fabian and Bung, Daniel Bernhard and Felder, Stefan and Mulligan, Sean and Oertel, Mario and Palermo, Michele},
  title     = {Hydraulic structures engineering: An evolving science in a changing world},
  series = {Wires Water},
  volume    = {8},
  journal   = {Wires Water},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2049-1948},
  doi       = {10.1002/wat2.1505},
  year      = {2021},
  language  = {en}
}
@article{BreuerRaueStrobeletal.2016,
  author    = {Breuer, Lars and Raue, Markus and Strobel, M. and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, R. and Wagner, Torsten},
  title     = {Hydrogels with incorporated graphene oxide as light-addressable actuator materials for cell culture environments in lab-on-chip systems},
  series = {Physica status solidi (a)},
  volume    = {213},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.201533056},
  pages     = {1520 -- 1525},
  year      = {2016},
  abstract  = {Abstractauthoren Graphene oxide (GO) nanoparticles were incorporated in temperature-sensitive Poly(N-isopropylacrylamide) (PNIPAAm) hydrogels. The nanoparticles increase the light absorption and convert light energy into heat efficiently. Thus, the hydrogels with GO can be stimulated spatially resolved by illumination as it was demonstrated by IR thermography. The temporal progression of the temperature maximum was detected for different concentrations of GO within the polymer network. Furthermore, the compatibility of PNIPAAm hydrogels with GO and cell cultures was investigated. For this purpose, culture medium was incubated with hydrogels containing GO and the viability and morphology of chinese hamster ovary (CHO) cells was examined after several days of culturing in presence of this medium.},
  language  = {en}
}
@article{DickhoffHorikawaFunke2021,
  author    = {Dickhoff, Jens and Horikawa, Atsushi and Funke, Harald},
  title     = {Hydrogen Combustion - new DLE Combustor Addresses NOx Emissions and Flashback},
  series = {Turbomachinery international : the global journal of energy equipment},
  volume    = {62},
  journal   = {Turbomachinery international : the global journal of energy equipment},
  number    = {4},
  publisher = {MJH Life Sciences},
  address   = {Cranbury},
  issn      = {2767-2328},
  pages     = {26 -- 27},
  year      = {2021},
  language  = {en}
}
@article{TixMollKrafftetal.2024,
  author    = {Tix, Julian and Moll, Fabian and Krafft, Simone and Betsch, Matthias and Tippk{\"o}tter, Nils},
  title     = {Hydrogen production from enzymatic pretreated organic waste with thermotoga neapolitana},
  series = {Energies},
  volume    = {17},
  journal   = {Energies},
  number    = {12},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en17122938},
  pages     = {20 Seiten},
  year      = {2024},
  abstract  = {Biomass from various types of organic waste was tested for possible use in hydrogen production. The composition consisted of lignified samples, green waste, and kitchen scraps such as fruit and vegetable peels and leftover food. For this purpose, the enzymatic pretreatment of organic waste with a combination of five different hydrolytic enzymes (cellulase, amylase, glucoamylase, pectinase and xylase) was investigated to determine its ability to produce hydrogen (H2) with the hydrolyzate produced here. In course, the anaerobic rod-shaped bacterium T. neapolitana was used for H2 production. First, the enzymes were investigated using different substrates in preliminary experiments. Subsequently, hydrolyses were carried out using different types of organic waste. In the hydrolysis carried out here for 48 h, an increase in glucose concentration of 481\% was measured for waste loads containing starch, corresponding to a glucose concentration at the end of hydrolysis of 7.5 g·L-1. In the subsequent set fermentation in serum bottles, a H2 yield of 1.26 mmol H2 was obtained in the overhead space when Terrific Broth Medium with glucose and yeast extract (TBGY medium) was used. When hydrolyzed organic waste was used, even a H2 yield of 1.37 mmol could be achieved in the overhead space. In addition, a dedicated reactor system for the anaerobic fermentation of T. neapolitana to produce H2 was developed. The bioreactor developed here can ferment anaerobically with a very low loss of produced gas. Here, after 24 h, a hydrogen concentration of 83\% could be measured in the overhead space.},
  language  = {en}
}
@article{RuebbelkeVoegeleGrajewskietal.2022,
  author    = {R{\"u}bbelke, Dirk and V{\"o}gele, Stefan and Grajewski, Matthias and Zobel, Luzy},
  title     = {Hydrogen-based steel production and global climate protection: An empirical analysis of the potential role of a European cross border adjustment mechanism},
  series = {Journal of Cleaner Production},
  volume    = {380},
  journal   = {Journal of Cleaner Production},
  number    = {Part 2, Art. Nr.:135040},
  publisher = {Elsevier},
  issn      = {0959-6526},
  doi       = {10.1016/j.jclepro.2022.135040},
  year      = {2022},
  abstract  = {The European Union's aim to become climate neutral by 2050 necessitates ambitious efforts to reduce carbon emissions. Large reductions can be attained particularly in energy intensive sectors like iron and steel. In order to prevent the relocation of such industries outside the EU in the course of tightening environmental regulations, the establishment of a climate club jointly with other large emitters and alternatively the unilateral implementation of an international cross-border carbon tax mechanism are proposed. This article focuses on the latter option choosing the steel sector as an example. In particular, we investigate the financial conditions under which a European cross border mechanism is capable to protect hydrogen-based steel production routes employed in Europe against more polluting competition from abroad. By using a floor price model, we assess the competitiveness of different steel production routes in selected countries. We evaluate the climate friendliness of steel production on the basis of specific GHG emissions. In addition, we utilize an input-output price model. It enables us to assess impacts of rising cost of steel production on commodities using steel as intermediates. Our results raise concerns that a cross-border tax mechanism will not suffice to bring about competitiveness of hydrogen-based steel production in Europe because the cost tends to remain higher than the cost of steel production in e.g. China. Steel is a classic example for a good used mainly as intermediate for other products. Therefore, a cross-border tax mechanism for steel will increase the price of products produced in the EU that require steel as an input. This can in turn adversely affect competitiveness of these sectors. Hence, the effects of higher steel costs on European exports should be borne in mind and could require the cross-border adjustment mechanism to also subsidize exports.},
  language  = {en}
}
@article{RibitschHeumannTrotschaetal.2011,
  author    = {Ribitsch, D. and Heumann, S. and Trotscha, E. and Herrero Acero, E. and Greimel, K. and Leber, R. and Birger-Gruenberger, R. and Deller, S. and Eiteljoerg, I. and Remler, P. and Weber, Th. and Siegert, Petra and Maurer, Karl-Heinz and Donelli, I. and Freddi, G. and Schwab, H. and Guebitz, G. M.},
  title     = {Hydrolysis of polyethyleneterephthalate by p-nitrobenzylesterase from Bacillus subtilis},
  series = {Biotechnology progress},
  volume    = {Vol. 27},
  journal   = {Biotechnology progress},
  number    = {Iss. 4},
  publisher = {Wiley},
  address   = {Hoboken},
  issn      = {1520-6033 (E-Journal); 8756-7938 (Print)},
  pages     = {951 -- 960},
  year      = {2011},
  language  = {en}
}
@article{FoersterBruggerMeinersetal.1994,
  author    = {F{\"o}rster, Arnold and Brugger, H. and Meiners, U. and Diniz, R.},
  title     = {Hydrostatic pressure sensors based on solid state tunneling devices / H. Brugger; U. Meiners ; R. Diniz ... A. F{\"o}rster ...},
  series = {Solid state electronics. 37 (1994), H. 4-6},
  journal   = {Solid state electronics. 37 (1994), H. 4-6},
  isbn      = {0038-1101},
  pages     = {801 -- 804},
  year      = {1994},
  language  = {en}
}
@article{BlomeKundt1987,
  author    = {Blome, Hans-Joachim and Kundt, W.},
  title     = {Hypersonic Jets from Young Stars in Molecular Clouds},
  series = {Circumstellar matter : proceedings of the 122nd symposium of the Internat. Astronom. Union held in Heidelberg, FRG, June 23 - 27, 1986 / ed. by I. Appenzeller ...},
  journal   = {Circumstellar matter : proceedings of the 122nd symposium of the Internat. Astronom. Union held in Heidelberg, FRG, June 23 - 27, 1986 / ed. by I. Appenzeller ...},
  publisher = {Reidel},
  address   = {Dordrecht u.a.},
  isbn      = {90-277-2511-X},
  pages     = {73 -- 74},
  year      = {1987},
  language  = {en}
}
@article{ArtmannGorbatenkovaPanasenko2000,
  author    = {Artmann, Gerhard and Gorbatenkova, E. A. and Panasenko, O. M.},
  title     = {Hypochlorous acid and human blood low density lipoproteins modified by hypochlorous acid increase erythrocyte adhesion to endothelial cells. Gorbatenkova, E. A.; Artmann, Gerhard Michael; Panasenko, O. M.},
  series = {Membrane and cell biology. 13 (2000), H. 4},
  journal   = {Membrane and cell biology. 13 (2000), H. 4},
  isbn      = {1023-6597},
  pages     = {537 -- 546},
  year      = {2000},
  language  = {en}
}
@article{DoorschodtSchreinemachersBehbahanietal.2011,
  author    = {Doorschodt, B. M. and Schreinemachers, M. C. J. M. and Behbahani, Mehdi and Florquin, S. and Weis, J. and Staat, Manfred and Tolba, R. H.},
  title     = {Hypothermic machine perfusion of kidney grafts: which pressure is preferred},
  series = {Annals of Biomedical Engineering. 39 (2011), H. 3},
  journal   = {Annals of Biomedical Engineering. 39 (2011), H. 3},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {1573-9686},
  pages     = {1051 -- 1059},
  year      = {2011},
  language  = {en}
}
@article{Grotendorst2012,
  author    = {Grotendorst, Johannes},
  title     = {IAS Winter School: Hierarchical Methods for Dynamics in Complex Molecular Systems},
  series = {Innovatives Supercomputing in Deutschland : inSiDE. 10 (2012), H. 1},
  journal   = {Innovatives Supercomputing in Deutschland : inSiDE. 10 (2012), H. 1},
  publisher = {-},
  pages     = {104},
  year      = {2012},
  language  = {en}
}
@article{DachwaldMikuckiTulaczyketal.2014,
  author    = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng},
  title     = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems},
  series = {Annals of Glaciology},
  volume    = {55},
  journal   = {Annals of Glaciology},
  number    = {65},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  issn      = {1727-5644},
  doi       = {10.3189/2014AoG65A004},
  pages     = {14 -- 22},
  year      = {2014},
  abstract  = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.},
  language  = {en}
}
@article{HillenLehmannHornetal.1995,
  author    = {Hillen, Walter and Lehmann, T. and Horn, H. and Schmitt, W.},
  title     = {IDEFIX - Identification of Dental Fixtures. Lehmann, T.; Hillen, W.; Horn, H.; Schmitt, W.},
  series = {5th European Congress on Dental and Maxillo-Facial Radiology : 30th Annual meeting of Working Group for Dental Radiology in the German Scientific Society for Dentistry, November 8-11, 1995, Cologne : abstracts},
  journal   = {5th European Congress on Dental and Maxillo-Facial Radiology : 30th Annual meeting of Working Group for Dental Radiology in the German Scientific Society for Dentistry, November 8-11, 1995, Cologne : abstracts},
  pages     = {[120] B. : graph. Darst.},
  year      = {1995},
  language  = {en}
}
@article{WerfelGuenthnerHapfelmeieretal.2022,
  author    = {Werfel, Stanislas and G{\"u}nthner, Roman and Hapfelmeier, Alexander and Hanssen, Henner and Kotliar, Konstantin and Heemann, Uwe and Schmaderer, Christoph},
  title     = {Identification of cardiovascular high-risk groups from dynamic retinal vessel signals using untargeted machine learning},
  series = {Cardiovascular Research},
  volume    = {118},
  journal   = {Cardiovascular Research},
  number    = {2},
  editor    = {Guzik, Tomasz J.},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {0008-6363},
  doi       = {10.1093/cvr/cvab040},
  pages     = {612 -- 621},
  year      = {2022},
  abstract  = {Dynamic retinal vessel analysis (DVA) provides a non-invasive way to assess microvascular function in patients and potentially to improve predictions of individual cardiovascular (CV) risk. The aim of our study was to use untargeted machine learning on DVA in order to improve CV mortality prediction and identify corresponding response alterations.},
  language  = {en}
}
@article{HillenLehmannHornetal.1996,
  author    = {Hillen, Walter and Lehmann, T. and Horn, H. and Schmitt, W.},
  title     = {Identification of Dental Fixtures in Intraoral X-rays. Lehmann, T.; Hillen, W.; Horn, H.; Schmitt, W.},
  series = {Medical imaging 1996 : image processing ; 12 - 15 February 1996, Newport Beach, California / Murray H. Loew ... chairs/ed.},
  journal   = {Medical imaging 1996 : image processing ; 12 - 15 February 1996, Newport Beach, California / Murray H. Loew ... chairs/ed.},
  publisher = {SPIE - The International Society for Optical Engineering},
  address   = {Bellingham, Wash.},
  isbn      = {0-8194-2085-9},
  pages     = {584 -- 584},
  year      = {1996},
  language  = {en}
}
@article{LempiaeinenCouttetBolognanietal.2012,
  author    = {Lempi{\"a}inen, Harri and Couttet, Philippe and Bolognani, Federico and M{\"u}ller, Arne and Dubost, Val{\´e}rie and Luisier, Rapha{\"e}lle and Rio-Espinola, Alberto del and Vitry, Veronique and Unterberger, Elif B. and Thomson, John P. and Treindl, Fridolin and Metzger, Ute and Wrzodek, Clemens and Hahne, Florian and Zollinger, Tulipan and Brasa, Sarah and Kalteis, Magdalena and Marcellin, Magali and Giudicelli, Fanny and Braeuning, Albert and Morawiec, Laurent and Zamurovic, Natasa and L{\"a}ngle, Ulrich and Scheer, Nico and Sch{\"u}beler, Dirk and Goodman, Jay and Chibout, Salah-Dine and Marlowe, Jennifer and Theil, Dietlinde and Heard, David J. and Grenet, Olivier and Zell, Andreas and Templin, Markus F. and Meehan, Richard R. and Wolf, Roland C. and Elcombe, Clifford R. and Schwarz, Michael and Moulin, Pierre and Terranova, R{\´e}mi and Moggs, Jonathan G.},
  title     = {Identification of Dlk1-Dio3 imprinted gene cluster non-coding RNAs as novel candidate biomarkers for liver tumor promotion},
  series = {Toxicological Sciences},
  volume    = {131},
  journal   = {Toxicological Sciences},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1094-2025},
  doi       = {10.1093/toxsci/kfs303},
  pages     = {375 -- 386},
  year      = {2012},
  abstract  = {The molecular events during nongenotoxic carcinogenesis and their temporal order are poorly understood but thought to include long-lasting perturbations of gene expression. Here, we have investigated the temporal sequence of molecular and pathological perturbations at early stages of phenobarbital (PB) mediated liver tumor promotion in vivo. Molecular profiling (mRNA, microRNA [miRNA], DNA methylation, and proteins) of mouse liver during 13 weeks of PB treatment revealed progressive increases in hepatic expression of long noncoding RNAs and miRNAs originating from the Dlk1-Dio3 imprinted gene cluster, a locus that has recently been associated with stem cell pluripotency in mice and various neoplasms in humans. PB induction of the Dlk1-Dio3 cluster noncoding RNA (ncRNA) Meg3 was localized to glutamine synthetase-positive hypertrophic perivenous hepatocytes, sug- gesting a role for β-catenin signaling in the dysregulation of Dlk1-Dio3 ncRNAs. The carcinogenic relevance of Dlk1-Dio3 locus ncRNA induction was further supported by in vivo genetic dependence on constitutive androstane receptor and β-catenin pathways. Our data identify Dlk1-Dio3 ncRNAs as novel candidate early biomarkers for mouse liver tumor promotion and provide new opportunities for assessing the carcinogenic potential of novel compounds.},
  language  = {en}
}
@article{Elbers2009,
  author    = {Elbers, Gereon},
  title     = {Identification of marker peptides in hair for discrimination with regard to species and breed / Koerner, Andrea ; Ring, Maike ; Fabry, Marlies ; Elbers, Gereon ; Moeller, Martin},
  series = {Proceedings of the Aachen-Dresden International Textile Conference, 3rd, Aachen, Germany, Nov. 26-27, 2009},
  journal   = {Proceedings of the Aachen-Dresden International Textile Conference, 3rd, Aachen, Germany, Nov. 26-27, 2009},
  publisher = {DWI},
  address   = {Aachen},
  pages     = {1 CD-ROM},
  year      = {2009},
  language  = {en}
}
@article{BialonskiLehnertz2006,
  author    = {Bialonski, Stephan and Lehnertz, Klaus},
  title     = {Identifying phase synchronization clusters in spatially extended dynamical systems},
  series = {Physical Review E},
  volume    = {74},
  journal   = {Physical Review E},
  number    = {5},
  issn      = {2470-0053},
  doi       = {10.1103/PhysRevE.74.051909},
  pages     = {051909},
  year      = {2006},
  language  = {en}
}
@article{Grap2007,
  author    = {Grap, Rolf Dietmar},
  title     = {If you think, education is expensive, try incompetence},
  series = {Beschaffung aktuell (2007)},
  journal   = {Beschaffung aktuell (2007)},
  isbn      = {0341-4507},
  pages     = {62 -- 63},
  year      = {2007},
  language  = {en}
}
@article{MiyamotoSugawaraKanohetal.2010,
  author    = {Miyamoto, Ko-ichiro and Sugawara, Yuri and Kanoh, Shin´ichiro and Yoshinobu, Tatsuo and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Image correction method for the chemical imaging sensor},
  series = {Sensors and Actuators B: Chemical. 144 (2010), H. 2},
  journal   = {Sensors and Actuators B: Chemical. 144 (2010), H. 2},
  pages     = {344 -- 348},
  year      = {2010},
  language  = {en}
}
@article{KallweitHelbingOrglmeisteretal.1994,
  author    = {Kallweit, Stephan and Helbing, M. and Orglmeister, R. and Siekmann, H. E.},
  title     = {Image Processing Techniques with Neural Networks for Flow Visualization in Rotating Machinery / Helbing, M. ; Orgimeiste, R. [Orglmeister, R.] ; Kallweit, S. ; Siekmann, H. E. ; Dues, M. ; Cronemeyer, J.},
  series = {FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Lab{\`e}ge / CERT/ONERA. General chairman Patrick Hebrard},
  journal   = {FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Lab{\`e}ge / CERT/ONERA. General chairman Patrick Hebrard},
  address   = {Toulouse},
  pages     = {87 -- 94},
  year      = {1994},
  language  = {en}
}
@article{VosLagemaatBarentszetal.2014,
  author    = {Vos, E. K. and Lagemaat, M. W. and Barentsz, J. O. and F{\"u}tterer, J. J. and Zamecnik, P. and Roozen, H. and Orzada, S. and Bitz, Andreas and Maas, M. C. and Scheenen, T. W. J.},
  title     = {Image quality and cancer visibility of T2-weighted Magnetic Resonance Imaging of the prostate at 7 Tesla},
  series = {European Radiology},
  volume    = {24},
  journal   = {European Radiology},
  number    = {8},
  publisher = {Springer},
  address   = {Cham},
  issn      = {1432-1084},
  doi       = {10.1007/s00330-014-3234-6},
  pages     = {1950 -- 1958},
  year      = {2014},
  abstract  = {Objectives To assess the image quality of T2-weighted (T2w) magnetic resonance imaging of the prostate and the visibility of prostate cancer at 7 Tesla (T). Materials \& methods Seventeen prostate cancer patients underwent T2w imaging at 7T with only an external transmit/receive array coil. Three radiologists independently scored images for image quality, visibility of anatomical structures, and presence of artefacts. Krippendorff's alpha and weighted kappa statistics were used to assess inter-observer agreement. Visibility of prostate cancer lesions was assessed by directly linking the T2w images to the confirmed location of prostate cancer on histopathology. Results T2w imaging at 7T was achievable with 'satisfactory' (3/5) to 'good' (4/5) quality. Visibility of anatomical structures was predominantly scored as 'satisfactory' (3/5) and 'good' (4/5). If artefacts were present, they were mostly motion artefacts and, to a lesser extent, aliasing artefacts and noise. Krippendorff's analysis revealed an α = 0.44 between three readers for the overall image quality scores. Clinically significant cancer lesions in both peripheral zone and transition zone were visible at 7T. Conclusion T2w imaging with satisfactory to good quality can be routinely acquired, and cancer lesions were visible in patients with prostate cancer at 7T using only an external transmit/receive body array coil.},
  language  = {en}
}
@article{HillenSchiebelZaengel1986,
  author    = {Hillen, Walter and Schiebel, U. and Zaengel, T.},
  title     = {Image quality in selenium-based digital radiography. Schiebel, U.; Hillen, W.; Zaengel, T.},
  series = {Medical Imaging},
  journal   = {Medical Imaging},
  pages     = {176},
  year      = {1986},
  language  = {en}
}
@article{PhilippEfthimiouPaganoetal.2022,
  author    = {Philipp, Mohr and Efthimiou, Nikos and Pagano, Fiammetta and Kratochwil, Nicolaus and Pizzichemi, Marco and Tsoumpas, Charalampos and Auffray, Etiennette and Ziemons, Karl},
  title     = {Image reconstruction analysis for positron emission tomography with heterostructured scintillators},
  series = {IEEE Transactions on Radiation and Plasma Medical Sciences},
  volume    = {7},
  journal   = {IEEE Transactions on Radiation and Plasma Medical Sciences},
  number    = {1},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2469-7311},
  doi       = {10.1109/TRPMS.2022.3208615},
  pages     = {41 -- 51},
  year      = {2022},
  abstract  = {The concept of structure engineering has been proposed for exploring the next generation of radiation detectors with improved performance. A TOF-PET geometry with heterostructured scintillators with a pixel size of 3.0×3.1×15 mm3 was simulated using Monte Carlo. The heterostructures consisted of alternating layers of BGO as a dense material with high stopping power and plastic (EJ232) as a fast light emitter. The detector time resolution was calculated as a function of the deposited and shared energy in both materials on an event-by-event basis. While sensitivity was reduced to 32\% for 100 μm thick plastic layers and 52\% for 50 μm, the CTR distribution improved to 204±49 ps and 220±41 ps respectively, compared to 276 ps that we considered for bulk BGO. The complex distribution of timing resolutions was accounted for in the reconstruction. We divided the events into three groups based on their CTR and modeled them with different Gaussian TOF kernels. On a NEMA IQ phantom, the heterostructures had better contrast recovery in early iterations. On the other hand, BGO achieved a better contrast to noise ratio (CNR) after the 15th iteration due to the higher sensitivity. The developed simulation and reconstruction methods constitute new tools for evaluating different detector designs with complex time responses.},
  language  = {en}
}
@article{Kurz2019,
  author    = {Kurz, Melanie},
  title     = {Images of Sweden in Germany: from Sundborn and Bullerby to Ikea},
  series = {nomad: the magazine for new design culture, business affairs and contemporary lifestyle},
  journal   = {nomad: the magazine for new design culture, business affairs and contemporary lifestyle},
  number    = {8},
  isbn      = {2513-0714},
  pages     = {136 -- 147},
  year      = {2019},
  language  = {en}
}
@article{HillenSchiebelZaengel1987,
  author    = {Hillen, Walter and Schiebel, U. and Zaengel, T.},
  title     = {Imaging performance of a digital storage phosphor system},
  series = {Medical Physics. 14 (1987), H. 5},
  journal   = {Medical Physics. 14 (1987), H. 5},
  isbn      = {0094-2405},
  pages     = {744 -- 751},
  year      = {1987},
  language  = {en}
}
@article{HillenRuppSchiebeletal.1989,
  author    = {Hillen, Walter and Rupp, S. and Schiebel, U. and Zaengel, Thomas T.},
  title     = {Imaging performance of a selenium-based detector for high-resolution radiography},
  series = {Medical Imaging III: Image Formation},
  journal   = {Medical Imaging III: Image Formation},
  isbn      = {0-8194-0125-0},
  pages     = {296},
  year      = {1989},
  language  = {en}
}
@article{FoersterSchmidtHaug1996,
  author    = {F{\"o}rster, Arnold and Schmidt, T. and Haug, R. J.},
  title     = {Imaging the local density of states in a disordered semiconductor / T. Schmidt ; R. J. Haug ; V. I. Fal'ko ... A. F{\"o}rster ...},
  series = {23rd International Conference on the Physics of Semiconductors : Berlin, Germany, July 21 - 26, 1996 / ed.: Matthias Scheffler ... - Vol. 3},
  journal   = {23rd International Conference on the Physics of Semiconductors : Berlin, Germany, July 21 - 26, 1996 / ed.: Matthias Scheffler ... - Vol. 3},
  publisher = {World Scientific},
  address   = {Singapore [u.a.]},
  isbn      = {981-02-2947-X},
  pages     = {2251 -- ff.},
  year      = {1996},
  language  = {en}
}
@article{BiselliLuellauDreisbachetal.1992,
  author    = {Biselli, Manfred and L{\"u}llau, E. and Dreisbach, C. and Grogg, A.},
  title     = {Immobilization of animal cells on chemically modified siran carrier / L{\"u}llau, E. ; Dreisbach, C. ; Grogg, A. ; Biselli, M. ; Wandrey, C.},
  series = {Animal cell technology : developments, processes, and products ; ESACT, European Society for Animal Cell Technology, the 11th meeting / Ed. R. E. Spier},
  journal   = {Animal cell technology : developments, processes, and products ; ESACT, European Society for Animal Cell Technology, the 11th meeting / Ed. R. E. Spier},
  publisher = {Butterworth-Heinemann},
  address   = {Oxford},
  isbn      = {0750604212},
  pages     = {469 -- 475},
  year      = {1992},
  language  = {en}
}
@article{MourzinaYoshinobuErmolenkoetal.2004,
  author    = {Mourzina, I.G. and Yoshinobu, T. and Ermolenko, Y.E. and Vlasov, Y. G. and Sch{\"o}ning, Michael Josef and Iwasaki, H.},
  title     = {Immobilization of urease and cholinesterase on the surface of semiconductor transducer for the development of light-addressable potentiometric sensors},
  series = {Technical digest of the 10th International Meeting on Chemical Sensors, July 11 - 14, 2004, Tsukuba, Japan / Japan Association of Chemical Sensors},
  journal   = {Technical digest of the 10th International Meeting on Chemical Sensors, July 11 - 14, 2004, Tsukuba, Japan / Japan Association of Chemical Sensors},
  publisher = {Japan Association of Chemical Sensors},
  address   = {Fukuoka},
  pages     = {788 -- 789},
  year      = {2004},
  language  = {en}
}
@article{MourzinaYoshinobuErmolenkoetal.2004,
  author    = {Mourzina, Ioulia G. and Yoshinobu, Tatsuo and Ermolenko, Yuri E. and Vlasov, Yuri G. and Sch{\"o}ning, Michael Josef and Iwasaki, H.},
  title     = {Immobilization of urease and cholinesterase on the surface of semiconductor transducer for the development of lightaddressable potentiometric sensors},
  series = {Microchimica Acta. 144 (2004), H. 1-3},
  journal   = {Microchimica Acta. 144 (2004), H. 1-3},
  isbn      = {0026-3672},
  pages     = {41 -- 50},
  year      = {2004},
  language  = {en}
}
@article{BogoyavlenskiyBerezinOgnevaetal.1999,
  author    = {Bogoyavlenskiy, A. P. and Berezin, V. E. and Ogneva, A. V. and Tolmacheva, V. P. and Digel, Ilya and Khudyakova, S. S.},
  title     = {Immunostimulating activity of a saponin-containing extract of Saponaria officinalis},
  series = {Voprosy virusologii},
  volume    = {44},
  journal   = {Voprosy virusologii},
  number    = {5},
  issn      = {0507-4088},
  pages     = {229 -- 232},
  year      = {1999},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Battery Performance on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aerospace Engineering},
  volume    = {33},
  journal   = {Journal of Aerospace Engineering},
  number    = {3},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001113},
  year      = {2020},
  abstract  = {Studies suggest that hybrid-electric aircraft have the potential to generate fewer emissions and be inherently quieter when compared to conventional aircraft. By operating combustion engines together with an electric propulsion system, synergistic benefits can be obtained. However, the performance of hybrid-electric aircraft is still constrained by a battery's energy density and discharge rate. In this paper, the influence of battery performance on the gross mass for a four-seat general aviation aircraft with a hybrid-electric propulsion system is analyzed. For this design study, a high-level approach is chosen, using an innovative initial sizing methodology to determine the minimum required aircraft mass for a specific set of requirements and constraints. Only the peak-load shaving operational strategy is analyzed. Both parallel- and serial-hybrid propulsion configurations are considered for two different missions. The specific energy of the battery pack is varied from 200 to 1,000 W⋅h/kg, while the discharge time, and thus the normalized discharge rating (C-rating), is varied between 30 min (2C discharge rate) and 2 min (30C discharge rate). With the peak-load shaving operating strategy, it is desirable for hybrid-electric aircraft to use a light, low capacity battery system to boost performance. For this case, the battery's specific power rating proved to be of much higher importance than for full electric designs, which have high capacity batteries. Discharge ratings of 20C allow a significant take-off mass reduction aircraft. The design point moves to higher wing loadings and higher levels of hybridization if batteries with advanced technology are used.},
  language  = {en}
}
@article{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs},
  series = {CEAS Aeronautical Journal},
  volume    = {10},
  journal   = {CEAS Aeronautical Journal},
  number    = {3},
  publisher = {Springer},
  issn      = {1869-5582 print},
  doi       = {10.1007/s13272-018-0352-x},
  pages     = {843},
  year      = {2018},
  abstract  = {One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost-benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters.},
  language  = {en}
}
@article{DachwaldMcDonaldMcInnesetal.2007,
  author    = {Dachwald, Bernd and McDonald, Malcolm and McInnes, Colin R. and Mengali, Giovanni},
  title     = {Impact of Optical Degradation on Solar Sail Mission Performance},
  series = {Journal of Spacecraft and Rockets. 44 (2007), H. 4},
  journal   = {Journal of Spacecraft and Rockets. 44 (2007), H. 4},
  isbn      = {0022-4650},
  pages     = {740 -- 749},
  year      = {2007},
  language  = {en}
}
@article{BoehnertBlaschkeBiewendt2023,
  author    = {B{\"o}hnert, Arno and Blaschke, Florian and Biewendt, Marcel},
  title     = {Impact of sustainability on the strategic direction of luxury companies},
  series = {European Journal of Marketing and Economics},
  volume    = {6},
  journal   = {European Journal of Marketing and Economics},
  number    = {1},
  publisher = {Revistia},
  address   = {London},
  issn      = {2601-8659},
  pages     = {70 -- 85},
  year      = {2023},
  abstract  = {Today's society is undergoing a paradigm shift driven by the megatrend of sustainability. This undeniably affects all areas of Western life. This paper aims to find out how the luxury industry is dealing with this change and what adjustments are made by the companies. For this purpose, interviews were conducted with managers from the luxury industry, in which they were asked about specific measures taken by their companies as well as trends in the industry. In a subsequent evaluation, the trends in the luxury industry were summarized for the areas of ecological, social, and economic sustainability. It was found that the area of environmental sustainability is significantly more focused than the other sub-areas. Furthermore, the need for a customer survey to validate the industry-based measures was identified.},
  language  = {en}
}
@article{WeberHekmatZimmermannetal.2004,
  author    = {Weber, Hans-Joachim and Hekmat, K. and Zimmermann, T. and Kampe, S.},
  title     = {Impact of tranexamic acid vs. aprotinin on blood loss and transfusion requirements after cardiopulmonary bypass: a prospective, randomised, double-blind trial / Hekmat, K. ; Zimmermann, T. ; Kampe, S. ; Kasper, S. M. ; Weber, H. J. ; Geissler, H. J. ; Meh},
  series = {Current Medical Research and Opinion. 20 (2004), H. 1},
  journal   = {Current Medical Research and Opinion. 20 (2004), H. 1},
  isbn      = {0300-7995},
  pages     = {121 -- 126},
  year      = {2004},
  language  = {en}
}
@article{PoghossianMaiMourzinaetal.2004,
  author    = {Poghossian, Arshak and Mai, D.-T. and Mourzina, Y. and Sch{\"o}ning, Michael Josef},
  title     = {Impedance effect of an ion-sensitive membrane: characterisation of an EMIS sensor by impedance spectroscopy, capacitance-voltage and constant-capacitance method},
  series = {Sensors and Actuators B. 103 (2004), H. 1-2},
  journal   = {Sensors and Actuators B. 103 (2004), H. 1-2},
  isbn      = {0925-4005},
  pages     = {423 -- 428},
  year      = {2004},
  language  = {en}
}
@article{SchusserLeinhosBaeckeretal.2013,
  author    = {Schusser, Sebastian and Leinhos, Marcel and B{\"a}cker, Matthias and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Impedance spectroscopy: A tool for real-time in situ monitoring of the degradation of biopolymers},
  series = {Physica Status Solidi (A)},
  volume    = {210},
  journal   = {Physica Status Solidi (A)},
  number    = {5},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1521-396X ; 0031-8965},
  doi       = {10.1002/pssa.201200941},
  pages     = {905 -- 910},
  year      = {2013},
  abstract  = {Investigation of the degradation kinetics of biodegradable polymers is essential for the development of implantable biomedical devices with predicted biodegradability. In this work, an impedimetric sensor has been applied for real-time and in situ monitoring of degradation processes of biopolymers. The sensor consists of two platinum thin-film electrodes covered by a polymer film to be studied. The benchmark biomedical polymer poly(D,L-lactic acid) (PDLLA) was used as a model system. PDLLA films were deposited on the sensor structure from a polymer solution by using the spin-coating method. The degradation kinetics of PDLLA films have been studied in alkaline solutions of pH 9 and 12 by means of an impedance spectroscopy (IS) method. Any changes in a polymer capacitance/resistance induced by water uptake and/or polymer degradation will modulate the global impedance of the polymer-covered sensor that can be used as an indicator of the polymer degradation. The degradation rate can be evaluated from the time-dependent impedance spectra. As expected, a faster degradation has been observed for PDLLA films exposed to pH 12 solution.},
  language  = {en}
}
@article{RiedelKartchemnikSchoeningetal.2014,
  author    = {Riedel, Marc and Kartchemnik, Julia and Sch{\"o}ning, Michael Josef and Lisdat, Fred},
  title     = {Impedimetric DNA detection - steps forward to sensorial application},
  series = {Analytical chemistry},
  volume    = {86 (2014)},
  journal   = {Analytical chemistry},
  number    = {15},
  publisher = {ACS Publications},
  address   = {Columbus},
  issn      = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)},
  doi       = {10.1021/ac501800q},
  pages     = {7867 -- 7874},
  year      = {2014},
  abstract  = {This study describes a label-free impedimetric sensor based on short ssDNA recognition elements for the detection of hybridization events. We concentrate on the elucidation of the influence of target length and recognition sequence position on the sensorial performance. The impedimetric measurements are performed in the presence of the redox system ferri-/ferrocyanide and show an increase in charge transfer resistance upon hybridization of ssDNA to the sensor surface. Investigations on the impedimetric signal stability demonstrate a clear influence of the buffers used during the sensor preparation and the choice of the passivating mercaptoalcanol compound. A stable sensor system has been developed, enabling a reproducible detection of 25mer target DNA in the low nanomolar range. After hybridization, a sensor regeneration can be reached with deionized water by adjustment of effective convection conditions, ensuring a sensor reusability. By investigations of longer targets with overhangs exposed to the solution, we can demonstrate applicability of the impedimetric detection for longer ssDNA. However, a decreasing charge transfer resistance change (ΔRct) is found by extending the overhang. As a strategy to increase the impedance change for longer target strands, the position of the recognition sequence can be designed in a way that a small overhang is exposed to the electrode surface. This is found to result in an increase in the relative Rct change. These results suggest that DNA and consequently negative charge near the electrode possess a larger impact on the impedimetric signal than DNA further away.},
  language  = {en}
}
@article{DelleHuckBaeckeretal.2015,
  author    = {Delle, Lotta E. and Huck, Christina and B{\"a}cker, Matthias and M{\"u}ller, Frank and Grandthyll, Samuel and Jacobs, Karin and Lilischkis, Rainer and Vu, Xuan T. and Sch{\"o}ning, Michael Josef and Wagner, Patrick and Thoelen, Roland and Weil, Maryam and Ingebrandt, Sven},
  title     = {Impedimetric immunosensor for the detection of histamine based on reduced graphene oxide},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431863},
  pages     = {1327 -- 1334},
  year      = {2015},
  language  = {en}
}
@article{FassbenderMoessleVogler1996,
  author    = {Faßbender, Heinz and M{\"o}ßle, Andrea and Vogler, Heiko},
  title     = {Implementation of a deterministic partial e-unification algorithm for macro tree transducers},
  series = {Journal of functional and logic programming. 1996 (1996), H. 2},
  journal   = {Journal of functional and logic programming. 1996 (1996), H. 2},
  isbn      = {1080-5230},
  year      = {1996},
  language  = {en}
}
@article{Fassbender1993,
  author    = {Faßbender, Heinz},
  title     = {Implementation of a universal unification algorithm for macro tree transducers},
  series = {Fundamentals of computation theory : proceedings / 9th International Conference, FCT '93, Szeged, Hungary, August 23 - 27, 1993. Zolt{\´a}n {\´E}sik (ed.)},
  journal   = {Fundamentals of computation theory : proceedings / 9th International Conference, FCT '93, Szeged, Hungary, August 23 - 27, 1993. Zolt{\´a}n {\´E}sik (ed.)},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {3-540-57163-9},
  pages     = {222 -- 233},
  year      = {1993},
  language  = {en}
}
@article{Fassbender1995,
  author    = {Faßbender, Heinz},
  title     = {Implementation of a UU-Algorithm for primitive recursive tree functions},
  series = {Fundamentals of computation theory : proceedings / 10th International Conference, FCT '95, Dresden, Germany, August 22 - 25, 1995. Horst Reichel (ed.)},
  journal   = {Fundamentals of computation theory : proceedings / 10th International Conference, FCT '95, Dresden, Germany, August 22 - 25, 1995. Horst Reichel (ed.)},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {3-540-60249-6},
  pages     = {233 -- 242},
  year      = {1995},
  language  = {en}
}
@article{MottaghyDijkshoorn2012,
  author    = {Mottaghy, Darius and Dijkshoorn, Lydia},
  title     = {Implementing an effective finite difference formulation for borehole heat exchangers into a heat and mass transport code},
  series = {Renewable Energy},
  volume    = {45},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.02.013},
  pages     = {59 -- 71},
  year      = {2012},
  abstract  = {We present an effective finite difference formulation for implementing and modeling multiple borehole heat exchangers (BHE) in the general 3-D coupled heat and flow transport code SHEMAT. The BHE with arbitrary length can be either coaxial or double U-shaped. It is particularly suitable for modeling deep BHEs which contain varying pipe diameters and materials. Usually, in numerical simulations, a fine discretization of the BHE assemblage is required, due to the large geometric aspect ratios involved. This yields large models and long simulation times. The approach avoids this problem by considering heat transport between fluid and the soil through pipes and grout via thermal resistances. Therefore, the simulation time can be significantly reduced. The coupling with SHEMAT is realized by introducing an effective heat generation. Due to this connection, it is possible to consider heterogeneous geological models, as well as the influence of groundwater flow. This is particularly interesting when studying the long term behavior of a single BHE or a BHE field. Heating and cooling loads can enter the model with an arbitrary interval, e.g. from hourly to monthly values. When dealing with large BHE fields, computing times can be further significantly reduced by focusing on the temperature field around the BHEs, without explicitly modeling inlet and outlet temperatures. This allows to determine the possible migration of cold and warm plumes due to groundwater flow, which is of particular importance in urban areas with a high BHE installation density. The model is validated against the existing BHE modeling codes EWS and EED. A comparison with monitoring data from a deep BHE in Switzerland shows a good agreement. Synthetic examples demonstrate the field of application of this model.},
  language  = {en}
}
@article{WissenBogdanskiScheeretal.2005,
  author    = {Wissen, M. and Bogdanski, N. and Scheer, H.-C. and Bitz, Andreas and Ahrens, G. and Gruetzner, G.},
  title     = {Implication of the light polarisation for UV curing of pre-patterned resists},
  series = {Microelectronic Engineering},
  volume    = {78-79},
  journal   = {Microelectronic Engineering},
  issn      = {0167-9317},
  doi       = {10.1016/j.mee.2004.12.099},
  pages     = {659 -- 664},
  year      = {2005},
  language  = {en}
}
@article{BreussKleefeld2020,
  author    = {Breuß, Michael and Kleefeld, Andreas},
  title     = {Implicit monotone difference methods for scalar conservation laws with source terms},
  series = {Acta Mathematica Vietnamica},
  volume    = {45},
  journal   = {Acta Mathematica Vietnamica},
  publisher = {Springer Singapore},
  address   = {Singapore},
  issn      = {2315-4144},
  doi       = {10.1007/s40306-019-00354-1},
  pages     = {709 -- 738},
  year      = {2020},
  abstract  = {In this article, a concept of implicit methods for scalar conservation laws in one or more spatial dimensions allowing also for source terms of various types is presented. This material is a significant extension of previous work of the first author (Breuß SIAM J. Numer. Anal. 43(3), 970-986 2005). Implicit notions are developed that are centered around a monotonicity criterion. We demonstrate a connection between a numerical scheme and a discrete entropy inequality, which is based on a classical approach by Crandall and Majda. Additionally, three implicit methods are investigated using the developed notions. Next, we conduct a convergence proof which is not based on a classical compactness argument. Finally, the theoretical results are confirmed by various numerical tests.},
  language  = {en}
}
@article{MakovickaGaertnerHardtetal.1997,
  author    = {Makovicka, C. and G{\"a}rtner, G. and Hardt, Arno and Hermann, W. and Wiechert, D. U.},
  title     = {Impregnated cathode surface investigations by SFM/STM and SEM/EDX},
  series = {Applied surface science. Vol. 111},
  journal   = {Applied surface science. Vol. 111},
  issn      = {1873-5584 (E-Journal); 0169-4332 (Print)},
  pages     = {70 -- 75},
  year      = {1997},
  language  = {en}
}
@article{KotterRiekert1983,
  author    = {Kotter, Michael and Riekert, L.},
  title     = {Impregnation-type catalysts with nonuniform distribution of the active component},
  series = {Chemical engineering fundamentals. 2 (1983)},
  journal   = {Chemical engineering fundamentals. 2 (1983)},
  isbn      = {0723-0966},
  pages     = {19 -- 38},
  year      = {1983},
  language  = {en}
}
@article{SchaeferBoegeShanjiaetal.1994,
  author    = {Sch{\"a}fer, Horst and Boege, P. and Shanjia, Xu and Xinzhang, Wu (u.a.)},
  title     = {Improved conductivity-measurement of semiconductor epitaxial layers by means of the contactless microwave method},
  series = {Conference digest : 10 - 14 January 1994, San Diego, California / International Conference on Millimeter and Submillimeter Waves and Applications / Mohammed N. Afsar, chair/ed.},
  journal   = {Conference digest : 10 - 14 January 1994, San Diego, California / International Conference on Millimeter and Submillimeter Waves and Applications / Mohammed N. Afsar, chair/ed.},
  publisher = {SPIE},
  address   = {Bellingham, Wash.},
  isbn      = {0-8194-1558-8},
  pages     = {649 -- 658},
  year      = {1994},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@article{LettiniHavermannGuidettietal.2010,
  author    = {Lettini, Antonio and Havermann, Marc and Guidetti, Marco and Fornaciari, Andrea},
  title     = {Improved functionalities and energy saving potential on mobile machines combining electronics with flow sharing valve and variable displacement pump},
  series = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  journal   = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  publisher = {-},
  isbn      = {978-3-940565-92-1},
  pages     = {103 -- 114},
  year      = {2010},
  language  = {en}
}
@article{BiselliNollEisenkraetzeretal.2002,
  author    = {Biselli, Manfred and Noll, Thomas and Eisenkr{\"a}tzer, Detlef and Kiesewetter, Andr{\´e}},
  title     = {Improved product formation in high density Chinese hamster ovary cell cultures transfected at confluency / Thomas Noll, Detlef Eisenkr{\"a}tzer, Andr{\´e} Kiesewetter, Andr{\´e} Dinter, Steffen Zeng, Christian Wandrey, Manfred Biselli und Eric G. Berger},
  series = {Biotechnology Letters. 24 (2002), H. 11},
  journal   = {Biotechnology Letters. 24 (2002), H. 11},
  isbn      = {0141-5492},
  pages     = {861 -- 866},
  year      = {2002},
  language  = {en}
}
@article{LowisFergusonPaulssenetal.2021,
  author    = {Lowis, Carsten and Ferguson, Simon and Paulßen, Elisabeth and Hoehr, Cornelia},
  title     = {Improved Sc-44 production in a siphon-style liquid target on a medical cyclotron},
  series = {Applied Radiation and Isotopes},
  volume    = {172},
  journal   = {Applied Radiation and Isotopes},
  number    = {Art. 109675},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0969-8043},
  doi       = {10.1016/j.apradiso.2021.109675},
  year      = {2021},
  language  = {en}
}
@article{MiyamotoSekiSutoetal.2018,
  author    = {Miyamoto, Koichiro and Seki, Kosuke and Suto, Takeyuki and Werner, Frederik and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Improved spatial resolution of the chemical imaging sensor with a hybrid illumination that suppresses lateral diffusion of photocarriers},
  series = {Sensor and Actuators B: Chemical},
  volume    = {273},
  journal   = {Sensor and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2018.07.016},
  pages     = {1328 -- 1333},
  year      = {2018},
  abstract  = {The chemical imaging sensor is a semiconductor-based chemical sensor capable of visualizing pH and ion distributions. The spatial resolution depends on the lateral diffusion of photocarriers generated by illumination of the semiconductor substrate. In this study, two types of optical setups, one based on a bundle of optical fibers and the other based on a binocular tube head, were developed to project a hybrid illumination of a modulated light beam and a ring-shaped constant illumination onto the sensor plate. An improved spatial resolution was realized by the ring-shaped constant illumination, which suppressed lateral diffusion of photocarriers by enhanced recombination due to the increased carrier concentration.},
  language  = {en}
}
@article{GriessmeierSonnenbergWeckesseretal.1996,
  author    = {Grießmeier, M. and Sonnenberg, F. and Weckesser, M. and Ziemons, Karl and Langen, K.-J. and M{\"u}ller-G{\"a}rtner, H. W.},
  title     = {Improvement of SPECT quantification in small brain structures by using experiment based recovery-coefficient corrections},
  series = {European Journal of Nuclear Medicine},
  volume    = {23},
  journal   = {European Journal of Nuclear Medicine},
  number    = {9},
  issn      = {1619-7089},
  pages     = {1238 -- 1238},
  year      = {1996},
  language  = {en}
}
@article{HajAyedKustererFunkeetal.2015,
  author    = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.},
  title     = {Improvement study for the dry-low-NOx hydrogen micromix combustion technology},
  series = {Propulsion and power research},
  volume    = {Vol. 4},
  journal   = {Propulsion and power research},
  number    = {Iss. 3},
  issn      = {2212-540X},
  doi       = {10.1016/j.jppr.2015.07.003},
  pages     = {132 -- 140},
  year      = {2015},
  language  = {en}
}
@article{HeuermannIbrahim2009,
  author    = {Heuermann, Holger and Ibrahim, Irfan},
  title     = {Improvements in the flicker noise reduction technique for osillator designs / Ibrahim, Irfan ; Heuermann, Holger},
  series = {European Microwave Conference, 2009 : EuMC 2009 ; Sept. 29, 2009 - Oct. 1, 2009, Rome, Italy ; part of European Microwave Week (EuMW) / sponsored by EuMA, European Microwave Association ... Endorsed by IEEE},
  journal   = {European Microwave Conference, 2009 : EuMC 2009 ; Sept. 29, 2009 - Oct. 1, 2009, Rome, Italy ; part of European Microwave Week (EuMW) / sponsored by EuMA, European Microwave Association ... Endorsed by IEEE},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  isbn      = {978-1-4244-4748-0},
  pages     = {1215 -- 1218},
  year      = {2009},
  language  = {en}
}
@article{ThomaGardiFisheretal.2024,
  author    = {Thoma, Andreas and Gardi, Alessandro and Fisher, Alex and Braun, Carsten},
  title     = {Improving local path planning for UAV flight in challenging environments by refining cost function weights},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (eISSN)},
  doi       = {10.1007/s13272-024-00741-x},
  pages     = {12 Seiten},
  year      = {2024},
  abstract  = {Unmanned Aerial Vehicles (UAV) constantly gain in versatility. However, more reliable path planning algorithms are required until full autonomous UAV operation is possible. This work investigates the algorithm 3DVFH* and analyses its dependency on its cost function weights in 2400 environments. The analysis shows that the 3DVFH* can find a suitable path in every environment. However, a particular type of environment requires a specific choice of cost function weights. For minimal failure, probability interdependencies between the weights of the cost function have to be considered. This dependency reduces the number of control parameters and simplifies the usage of the 3DVFH*. Weights for costs associated with vertical evasion (pitch cost) and vicinity to obstacles (obstacle cost) have the highest influence on the failure probability of the local path planner. Environments with mainly very tall buildings (like large American city centres) require a preference for horizontal avoidance manoeuvres (achieved with high pitch cost weights). In contrast, environments with medium-to-low buildings (like European city centres) benefit from vertical avoidance manoeuvres (achieved with low pitch cost weights). The cost of the vicinity to obstacles also plays an essential role and must be chosen adequately for the environment. Choosing these two weights ideal is sufficient to reduce the failure probability below 10\%.},
  language  = {en}
}
@article{SchrothSchoeningSchuetzetal.1999,
  author    = {Schroth, P. and Sch{\"o}ning, Michael Josef and Sch{\"u}tz, S. and Epanya, P. and Steffen, A. and Weißbecker, B. and Hummel, Hans E. and Kordos, P. and L{\"u}th, H.},
  title     = {Improving the bioelectronic interface of an antenna/chip biosensor - technological aspects},
  series = {Proceedings : The Hague, The Netherlands, September 12 - 15, 1999 / [ed. by M. Bartek]. Vol 1.},
  journal   = {Proceedings : The Hague, The Netherlands, September 12 - 15, 1999 / [ed. by M. Bartek]. Vol 1.},
  address   = {The Hague, The Netherlands},
  isbn      = {90-76699-02-X},
  pages     = {569 -- 572},
  year      = {1999},
  language  = {en}
}
@article{ThustSchrothToepleretal.1998,
  author    = {Thust, M. and Schroth, P. and T{\"o}pler, A. and Sch{\"o}ning, Michael Josef and M{\"u}ller-Veggian, Mattea and Kordos, P. and L{\"u}th, H.},
  title     = {Improving the detection limit of a capacitive sensor by means of a diffusion barrier},
  series = {Eurosensors XII : proceedings of the 12th European Conference on Solid-State Transducers and the 9th UK Conference on Sensors and their Applications, Southampton, UK, 13 - 16 September 1998 / ed. by N. M. White ; Vol. 1},
  journal   = {Eurosensors XII : proceedings of the 12th European Conference on Solid-State Transducers and the 9th UK Conference on Sensors and their Applications, Southampton, UK, 13 - 16 September 1998 / ed. by N. M. White ; Vol. 1},
  publisher = {Inst. of Physics Publ.},
  address   = {Bristol [u.a.]},
  isbn      = {0-7503-0595-9},
  pages     = {507 -- 510},
  year      = {1998},
  language  = {en}
}
@article{CosmaKesslerGebhardtetal.2020,
  author    = {Cosma, Cosmin and Kessler, Julia and Gebhardt, Andreas and Campbell, Ian and Balc, Nicolae},
  title     = {Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed},
  series = {Materials},
  volume    = {13},
  journal   = {Materials},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1944},
  doi       = {10.3390/ma13040905},
  pages     = {1 -- 18},
  year      = {2020},
  abstract  = {To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10\% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250-1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20\% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L.},
  language  = {en}
}
@article{NoureddineKraffLaddetal.2017,
  author    = {Noureddine, Yacine and Kraff, Oliver and Ladd, Mark E. and Wrede, Karsten H. and Chen, Bixia and Quick, Harald H. and Schaefers, Gregor and Bitz, Andreas},
  title     = {In vitro and in silico assessment of RF-induced heating around intracranial aneurysm clips at 7 Tesla},
  series = {Magnetic Resonance in Medicine},
  journal   = {Magnetic Resonance in Medicine},
  number    = {Early view},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.26650},
  pages     = {14 Seiten},
  year      = {2017},
  language  = {en}
}
@article{TemizArtmannResmiAkhunlaretal.2005,
  author    = {Temiz Artmann, Ayseg{\"u}l and Resmi, Halil and Akhunlar, H{\"u}lya and G{\"u}ner, G{\"u}l},
  title     = {In vitro effects of high glucose concentrations on membrane protein sulfhydryl oxidation, G-actin and deformability of human erythrocytes. Resmi, Halil ; Akhunlar, H{\"u}lya ; Temiz Artmann, Ayseg{\"u}l ; G{\"u}ner, G{\"u}l},
  series = {Cell biochemistry and function. 23 (2005), H. 3},
  journal   = {Cell biochemistry and function. 23 (2005), H. 3},
  isbn      = {0263-6484},
  pages     = {163 -- 168},
  year      = {2005},
  language  = {en}
}
@article{TemizArtmannBaskurtEdremitlioglu1994,
  author    = {Temiz Artmann, Ayseg{\"u}l and Baskurt, O. K. and Edremitlioglu, M.},
  title     = {In vitro effects of in vivo activated leukocytes on red blood cell filterability and lipid peroxidation. Baskurt, O.K.; Edremitlioglu, M.; Temiz, A.},
  series = {Clinical Hemorheology. 14 (1994), H. 4},
  journal   = {Clinical Hemorheology. 14 (1994), H. 4},
  pages     = {591 -- 596},
  year      = {1994},
  language  = {en}
}
@article{BleilevensHillGrzannaetal.2019,
  author    = {Bleilevens, Christian and Hill, Aileen and Grzanna, Tim and Fechter, Tamara and Bohnen, Melanie and Weber, Hans-Joachim and Beckers, Christian and Borosch, Sebastian and Zayat, Rashad and Benstoem, Carin and Rossaint, Rolf and Goetzenich, Andreas},
  title     = {In vitro head-to-head comparison of anticoagulation properties of two heparin brands in a human blood miniature mock loop},
  series = {Interactive cardiovascular and thoracic surgery},
  volume    = {28},
  journal   = {Interactive cardiovascular and thoracic surgery},
  number    = {1},
  issn      = {1569-9285},
  doi       = {10.1093/icvts/ivy206},
  pages     = {120 -- 127},
  year      = {2019},
  language  = {en}
}
@article{BrockhausBehbahaniMurisetal.2021,
  author    = {Brockhaus, Moritz K. and Behbahani, Mehdi and Muris, Farina and Jansen, Sebastian V. and Schmitz- Rode, Thomas and Steinseifer, Ulrich and Clauser, Johanna C.},
  title     = {In vitro thrombogenicity testing of pulsatile mechanical circulatory support systems: Design and proof-of-concept},
  series = {Artificial Organs},
  volume    = {45},
  journal   = {Artificial Organs},
  number    = {12},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1525-1594},
  doi       = {10.1111/aor.14046},
  pages     = {1513 -- 1521},
  year      = {2021},
  abstract  = {Thrombogenic complications are a main issue in mechanical circulatory support (MCS). There is no validated in vitro method available to quantitatively assess the thrombogenic performance of pulsatile MCS devices under realistic hemodynamic conditions. The aim of this study is to propose a method to evaluate the thrombogenic potential of new designs without the use of complex in-vivo trials. This study presents a novel in vitro method for reproducible thrombogenicity testing of pulsatile MCS systems using low molecular weight heparinized porcine blood. Blood parameters are continuously measured with full blood thromboelastometry (ROTEM; EXTEM, FIBTEM and a custom-made analysis HEPNATEM). Thrombus formation is optically observed after four hours of testing. The results of three experiments are presented each with two parallel loops. The area of thrombus formation inside the MCS device was reproducible. The implantation of a filter inside the loop catches embolizing thrombi without a measurable increase of platelet activation, allowing conclusions of the place of origin of thrombi inside the device. EXTEM and FIBTEM parameters such as clotting velocity (α) and maximum clot firmness (MCF) show a total decrease by around 6\% with a characteristic kink after 180 minutes. HEPNATEM α and MCF rise within the first 180 minutes indicate a continuously increasing activation level of coagulation. After 180 minutes, the consumption of clotting factors prevails, resulting in a decrease of α and MCF. With the designed mock loop and the presented protocol we are able to identify thrombogenic hot spots inside a pulsatile pump and characterize their thrombogenic potential.},
  language  = {en}
}
@article{KobusBitzUdenetal.2012,
  author    = {Kobus, Thiele and Bitz, Andreas and Uden, Mark J. van and Lagemaat, Miram W. and Rothgang, Eva and Orzada, Stephan and Heerschap, Arend and Scheenen, Tom W. J.},
  title     = {In vivo 31P MR spectroscopic imaging of the human prostate at 7 T: safety and feasibility},
  series = {Magnetic Resonance in Medicine},
  volume    = {68},
  journal   = {Magnetic Resonance in Medicine},
  number    = {6},
  publisher = {Wiley-Liss},
  address   = {New York},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.24175},
  pages     = {1683 -- 1695},
  year      = {2012},
  abstract  = {31P MR spectroscopic imaging of the human prostate provides information about phosphorylated metabolites that could be used for prostate cancer characterization. The sensitivity of a magnetic field strength of 7 T might enable 3D 31P MR spectroscopic imaging with relevant spatial resolution in a clinically acceptable measurement time. To this end, a 31P endorectal coil was developed and combined with an eight-channel 1H body-array coil to relate metabolic information to anatomical location. An extensive safety validation was performed to evaluate the specific absorption rate, the radiofrequency field distribution, and the temperature distribution of both coils. This validation consisted of detailed Finite Integration Technique simulations, confirmed by MR thermometry and Burn:x-wiley:07403194:media:MRM24175:tex2gif-stack-1 measurements in a phantom and in vivo temperature measurements. The safety studies demonstrated that the presence of the 31P endorectal coil had no influence on the specific absorption rate levels and temperature distribution of the external eight-channel 1H array coil. To stay within a 10 g averaged local specific absorption rate of 10 W/kg, a maximum time-averaged input power of 33 W for the 1H array coil was allowed. For transmitting with the 31P endorectal coil, our safety limit of less than 1°C temperature increase in vivo during a 15-min MR spectroscopic imaging experiment was reached at a time-averaged input power of 1.9 W. With this power setting, a second in vivo measurement was performed on a healthy volunteer. Using adiabatic excitation, 3D 31P MR spectroscopic imaging produced spectra from the entire prostate in 18 min with a spatial resolution of 4 cm3. The spectral resolution enabled the separate detection of phosphocholine, phosphoethanolamine, inorganic phosphate, and other metabolites that could play an important role in the characterization of prostate cancer.},
  language  = {en}
}
@article{PorschenGartzenGewehretal.1978,
  author    = {Porschen, W. and Gartzen, J. and Gewehr, K. and M{\"u}hlensiepen, H. and Weber, Hans-Joachim and Feinedegen, L E.},
  title     = {In vivo assay of the radiation sensitivity of hypoxic tumour cells : influence of γ-rays, cyclotron neutrons, misonidazole, hyperthermia and mixed modalities},
  series = {The British journal of cancer / Supplement},
  journal   = {The British journal of cancer / Supplement},
  number    = {3},
  publisher = {Lewis},
  address   = {London},
  issn      = {0306-9443},
  pages     = {194 -- 197},
  year      = {1978},
  abstract  = {Tumour cell death can be evaluated in the living mouse by externally measuring the rate of loss of tumour-bound DNA tracer. By sequentially labelling the tumour-bearing animals with ¹²⁵IUdR and ¹³¹IUdR 50 h apart, the average tumour cells at the time of the second injection are labelled by ¹²⁵IUdR and the euoxic tumour cells are specifically labelled with ¹³¹IUdR. Tumour treatment at this stage of labelling permits the observation of the reaction of euoxic cells and average tumour cells and finally yields data on hypoxic cells and thus on the oxygen enhancement ratio. This information adds to results from tumour control and growth delay. With this technique effects were analysed of 60-Co γ-rays, cyclotron neutrons (E = 6 MeV), misonidazole (500 mg/kg body wt) and hyperthermia (42°C water-bath), or combinations of these. Misonidazole (15 min before irradiation) altered the oxygen enhancement ratio by a factor of 1·5 for γ-rays and of 1·1 for neutrons; when evaluated from tumour-growth delay and TCD-50 misonidazole gave a dose modifying factor of 1·47 for γ-rays and of 1·2-1·3 for neutrons. Based on percentage tumour regression 100 days after treatment, the enhancement ratio from hyperthermia (after irradiation) was 2·75 for γ-rays (at 10 Gray) and 2·2 for neutrons (at 3·2 Gray). For neutrons combined with misonidazole and hyperthermia the ratio was 2·4. These results demonstrate that effects of neutron irradiation may be modified by electron-affinic substances and/or hyperthermia.},
  language  = {en}
}
@article{ScheerRossKapelyukhetal.2010,
  author    = {Scheer, Nico and Ross, Jillian and Kapelyukh, Yury and Rode, Anja and Wolf, C. Roland},
  title     = {In vivo responses of the human and murine pregnane X receptor to dexamethasone in mice},
  series = {Drug Metabolism and Disposition},
  volume    = {38},
  journal   = {Drug Metabolism and Disposition},
  number    = {7},
  publisher = {ASPET},
  address   = {Bethesda},
  issn      = {1521-009X},
  doi       = {10.1124/dmd.109.031872},
  pages     = {1046 -- 1053},
  year      = {2010},
  abstract  = {Dexamethasone (DEX) is a potent and widely used anti-inflammatory and immunosuppressant glucocorticoid. It can bind and activate the pregnane X receptor (PXR), which plays a critical role as xenobiotic sensor in mammals to induce the expression of many enzymes, including cytochromes P450 in the CYP3A family. This induction results in its own metabolism. We have used a series of transgenic mouse lines, including a novel, improved humanized PXR line, to compare the induction profile of PXR-regulated drug-metabolizing enzymes after DEX administration, as well as looking at hepatic responses to rifampicin (RIF). The new humanized PXR model has uncovered further intriguing differences between the human and mouse receptors in that RIF only induced Cyp2b10 in the new humanized model. DEX was found to be a much more potent inducer of Cyp3a proteins in wild-type mice than in mice humanized for PXR. To assess whether PXR is involved in the detoxification of DEX in the liver, we analyzed the consequences of high doses of the glucocorticoid on hepatotoxicity on different PXR genetic backgrounds. We also studied these effects in an additional mouse model in which functional mouse Cyp3a genes have been deleted. These strains exhibited different sensitivities to DEX, indicating a protective role of the PXR and CYP3A proteins against the hepatotoxicity of this compound.},
  language  = {en}
}
@article{MuellerVeggianHaenniBeuscheretal.1979,
  author    = {M{\"u}ller-Veggian, Mattea and Haenni, D. R. and Beuscher, H. and Lieder, R. M.},
  title     = {In-beam studies of ¹⁴⁵ Gd and ¹⁴⁵ Eu},
  series = {Fr{\"u}hjahrstagung ... des Fachausschusses Kernphysik und Hochenergiephysik der DPG (Sektion A: Kernphysik) / Deutsche Physikalische Gesellschaft (1979)},
  journal   = {Fr{\"u}hjahrstagung ... des Fachausschusses Kernphysik und Hochenergiephysik der DPG (Sektion A: Kernphysik) / Deutsche Physikalische Gesellschaft (1979)},
  year      = {1979},
  language  = {en}
}
@article{MuellerVeggianZuberGueven1988,
  author    = {M{\"u}ller-Veggian, Mattea and Zuber, K. and Gueven, H.},
  title     = {In-beam study of 63 143 Eu 80},
  series = {Zeitschrift f{\"u}r Physik / A, Hadrons and nuclei. 330 (1988), H. 3},
  journal   = {Zeitschrift f{\"u}r Physik / A, Hadrons and nuclei. 330 (1988), H. 3},
  isbn      = {1431-5831},
  pages     = {343 -- 344},
  year      = {1988},
  language  = {en}
}
@article{MuellerVeggianHaenniBeuscheretal.1980,
  author    = {M{\"u}ller-Veggian, Mattea and Haenni, D. R. and Beuscher, H. and Lieder, R. M.},
  title     = {In-beam study of levels in ¹⁴⁵ Eu},
  series = {Structure of medium-heavy nuclei, 1979 : proceedings of the 6. European Physical Soc. Nuclear Divisional Conference on the Structure of Medium-Heavy Nuclei held in Rhodes, Greece, 1-4 May 1979 / ed. Committee: G. S. Anagnostatos ... - (Conference series / Institute of Physics London, Bristol ; 49)},
  journal   = {Structure of medium-heavy nuclei, 1979 : proceedings of the 6. European Physical Soc. Nuclear Divisional Conference on the Structure of Medium-Heavy Nuclei held in Rhodes, Greece, 1-4 May 1979 / ed. Committee: G. S. Anagnostatos ... - (Conference series / Institute of Physics London, Bristol ; 49)},
  publisher = {Inst. of Physics},
  address   = {Bristol},
  isbn      = {0-85498-140-3},
  pages     = {131},
  year      = {1980},
  language  = {en}
}
@article{MuellerVeggianBeuscherHaenni1980,
  author    = {M{\"u}ller-Veggian, Mattea and Beuscher, H. and Haenni, D. R.},
  title     = {In-beam study of the light transitional nucleus ¹³⁸ Nd},
  series = {Annual report 1979 / Kernforschungsanlage J{\"u}lich Institut f{\"u}r Kernphysik / Hrsg.: A. F{\"a}ssler. - (Spezielle Berichte der Kernforschungsanlage J{\"u}lich ; 72)},
  journal   = {Annual report 1979 / Kernforschungsanlage J{\"u}lich Institut f{\"u}r Kernphysik / Hrsg.: A. F{\"a}ssler. - (Spezielle Berichte der Kernforschungsanlage J{\"u}lich ; 72)},
  publisher = {Kernforschungsanlage},
  address   = {J{\"u}lich},
  pages     = {45},
  year      = {1980},
  language  = {en}
}
@article{MuellerVeggianMorekBeuscheretal.1985,
  author    = {M{\"u}ller-Veggian, Mattea and Morek, T. and Beuscher, H. and Bochev, B.},
  title     = {In-beam study of the odd-odd nuclei ¹³⁴ La and ¹³⁶ La},
  series = {Nuclear physics / A, Nuclear and hadronic physics. 433 (1985), H. 2},
  journal   = {Nuclear physics / A, Nuclear and hadronic physics. 433 (1985), H. 2},
  isbn      = {0375-9474},
  pages     = {159 -- 180},
  year      = {1985},
  language  = {en}
}
@article{MuellerVeggianZuberGueven1988,
  author    = {M{\"u}ller-Veggian, Mattea and Zuber, K. and Gueven, H.},
  title     = {In-beam study of ¹⁴³ Eu},
  series = {Annual report 1987 / Kernforschungsanlage J{\"u}lich Institut f{\"u}r Kernphysik / Gr{\"u}mmer , F. (Hrsg.) . - (Spezielle Berichte der Kernforschungsanlage J{\"u}lich ; 442)},
  journal   = {Annual report 1987 / Kernforschungsanlage J{\"u}lich Institut f{\"u}r Kernphysik / Gr{\"u}mmer , F. (Hrsg.) . - (Spezielle Berichte der Kernforschungsanlage J{\"u}lich ; 442)},
  publisher = {Verlag des Forschungszentrums J{\"u}lich},
  address   = {J{\"u}lich},
  pages     = {44},
  year      = {1988},
  language  = {en}
}
@article{MuellerVeggianMariscottiBeuscheretal.1978,
  author    = {M{\"u}ller-Veggian, Mattea and Mariscotti, M. A. J. and Beuscher, H. and Davidson, W. F.},
  title     = {In-beam study of ¹⁴⁴ Gd},
  series = {Nuclear physics / A. 311 (1978), H. 3},
  journal   = {Nuclear physics / A. 311 (1978), H. 3},
  isbn      = {0375-9474},
  pages     = {395 -- 412},
  year      = {1978},
  language  = {en}
}
@article{MuellerVeggianMariscottiBeuscheretal.1978,
  author    = {M{\"u}ller-Veggian, Mattea and Mariscotti, M. A. J. and Beuscher, H. and Davidson, W. F.},
  title     = {In-beam study of ¹⁴⁴ Gd},
  series = {Proceedings of the International Conference on Nuclear Structure : Tokyo, Sept. 5 - 10, 1977 / ed. by T. Marumori. - Journal of the Physical Society of Japan ; Vol. 44, 1978 : Suppl.},
  journal   = {Proceedings of the International Conference on Nuclear Structure : Tokyo, Sept. 5 - 10, 1977 / ed. by T. Marumori. - Journal of the Physical Society of Japan ; Vol. 44, 1978 : Suppl.},
  publisher = {Physical Soc. of Japan},
  address   = {Tokyo},
  pages     = {863},
  year      = {1978},
  language  = {en}
}
@article{MuellerVeggianMariscottiBeuscheretal.1977,
  author    = {M{\"u}ller-Veggian, Mattea and Mariscotti, M. A. J. and Beuscher, H. and Davidson, W. F.},
  title     = {In-beam study of ¹⁴⁴ Gd},
  series = {Annual report 1976 / Institut f{\"u}r Kernphysik Kernforschungsanlage J{\"u}lich / Ed. board: A. F{\"a}ßler ...},
  journal   = {Annual report 1976 / Institut f{\"u}r Kernphysik Kernforschungsanlage J{\"u}lich / Ed. board: A. F{\"a}ßler ...},
  publisher = {Kernforschungsanlage},
  address   = {J{\"u}lich},
  pages     = {37},
  year      = {1977},
  language  = {en}
}
@article{MuellerVeggianHaenniBeuscheretal.1979,
  author    = {M{\"u}ller-Veggian, Mattea and Haenni, D. R. and Beuscher, H. and Lieder, R. M.},
  title     = {In-beam study of ¹⁴⁵ Gd},
  series = {Annual report 1978 / Kernforschungsanlage J{\"u}lich Institut f{\"u}r Kernphysik / Hrsg.: A. F{\"a}ssler. - (Spezielle Berichte der Kernforschungsanlage J{\"u}lich ; 36)},
  journal   = {Annual report 1978 / Kernforschungsanlage J{\"u}lich Institut f{\"u}r Kernphysik / Hrsg.: A. F{\"a}ssler. - (Spezielle Berichte der Kernforschungsanlage J{\"u}lich ; 36)},
  publisher = {Kernforschungsanlage},
  address   = {J{\"u}lich},
  pages     = {27},
  year      = {1979},
  language  = {en}
}
@article{MuellerVeggianGonoLieder1979,
  author    = {M{\"u}ller-Veggian, Mattea and Gono, Y. and Lieder, R. M.},
  title     = {In-beam γ-ray study of ¹⁸⁹,¹⁹¹,¹⁹³ Au},
  series = {Nuclear physics / A. 327 (1979), H. 2},
  journal   = {Nuclear physics / A. 327 (1979), H. 2},
  isbn      = {0375-9474},
  pages     = {269 -- 287},
  year      = {1979},
  language  = {en}
}
@article{MuellerVeggianKreinerFenzletal.1978,
  author    = {M{\"u}ller-Veggian, Mattea and Kreiner, A. J. and Fenzl, M. and Kutschera, W.},
  title     = {In-beam γ-spectroscopic investigation of ¹⁹⁶ Tl},
  series = {Annual report 1977 / Institut f{\"u}r Kernphysik Kernforschungsanlage J{\"u}lich},
  journal   = {Annual report 1977 / Institut f{\"u}r Kernphysik Kernforschungsanlage J{\"u}lich},
  publisher = {Verlag des Forschungszentrums J{\"u}lich},
  address   = {J{\"u}lich},
  pages     = {47 -- 48},
  year      = {1978},
  language  = {en}
}
@article{TeumerCapitainRossJonesetal.2018,
  author    = {Teumer, T. and Capitain, C. and Ross-Jones, J. and Tippk{\"o}tter, Nils and R{\"a}dle, M. and Methner, F.-J.},
  title     = {In-line Haze Monitoring Using a Spectrally Resolved Back Scattering Sensor},
  series = {BrewingScience},
  volume    = {71},
  journal   = {BrewingScience},
  number    = {5/6},
  publisher = {Fachverlag Hans Carl},
  address   = {N{\"u}rnberg},
  issn      = {1613-2041},
  pages     = {49 -- 55},
  year      = {2018},
  abstract  = {In the present work an optical sensor in combination with a spectrally resolved detection device for in-line particle-size-monitoring for quality control in beer production is presented. The principle relies on the size and wavelength dependent backscatter of growing particles in fluids. Measured interference structures of backscattered light are compared with calculated theoretical values, based on Mie-Theory, and fitted with a linear least square method to obtain particle size distributions. For this purpose, a broadband light source in combination with a process-CCD-spectrometer (charge ? coupled device spectrometer) and process adapted fiber optics are used. The goal is the development of an easy and flexible measurement device for in-line-monitoring of particle size. The presented device can be directly installed in product fill tubes or vessels, follows CIP- (cleaning in place) and removes the need of sample taking. A proof of concept and preliminary results, measuring protein precipitation, are presented.},
  language  = {en}
}