@inproceedings{WeissAbanteribaEsch2007,
  author    = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas},
  title     = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow},
  series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  publisher = {American Society of Mechanical Engineers (ASME)},
  address   = {New York},
  isbn      = {0-7918-4288-6},
  doi       = {10.1115/FEDSM2007-37387},
  pages     = {1861 -- 1871},
  year      = {2007},
  abstract  = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.},
  language  = {en}
}
@inproceedings{HuberBleckScheiketal.2011,
  author    = {Huber, Fr{\´e}d{\´e}ric and Bleck, Wolfgang and Scheik, Sven and Schleser, Markus and Reisgen, Uwe},
  title     = {Investigation of galvanneal coating adherence in adhesive bonded joints using lap shear test},
  series = {Galvatech 2011 : 8th International Conference on Zinc and Zinc Alloy Coated Steel Sheet, June 21 - 24, 2011, Genova (Italy) ; proceedings},
  booktitle = {Galvatech 2011 : 8th International Conference on Zinc and Zinc Alloy Coated Steel Sheet, June 21 - 24, 2011, Genova (Italy) ; proceedings},
  publisher = {Associazione Italiana di Metallurgia},
  address   = {Mailand},
  organization    = {International Conference on Zinc and Zinc Alloy Coated Steel Sheet <8, 2011, Genua>},
  isbn      = {978-88-85298-82-8},
  pages     = {Paper No. 43},
  year      = {2011},
  language  = {en}
}
@inproceedings{KubalskiButenwegMarinkovićetal.2017,
  author    = {Kubalski, T. and Butenweg, Christoph and Marinković, Marko and Klinkel, S.},
  title     = {Investigation Of The Seismic Behaviour Of Infill Masonry Using Numerical Modelling Approaches},
  series = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  pages     = {1 -- 11},
  year      = {2017},
  abstract  = {Masonry is a widely spread construction type which is used all over the world for different types of structures. Due to its simple and cheap construction, it is used as non-structural as well as structural element. In frame structures, such as reinforced concrete frames, masonry may be used as infill. While the bare frame itself is able to carry the loads when it comes to seismic events, the infilled frame is not able to warp freely due to the constrained movement. This restraint results in a complex interaction between the infill and the surrounding frame, which may lead to severe damage to the infill as well as the surrounding frame. The interaction is studied in different projects and effective approaches for the description of the behavior are still lacking. Experimental programs are usually quite expensive, while numerical models, once validated, do offer an efficient approach for the investigation of the interaction when horizontally loaded. In order to study the numerous parameters influencing the seismic load bearing behavior, numerical models may be used. Therefore, this contribution presents a numerical approach for the simulation of infill masonry in reinforced concrete frames. Both parts, the surrounding frame as well as the infill are represented by micro modelling approaches to correctly take into account the different types of failure. The adopted numerical model describes the inelastic behavior of the system, as indicated by the obtained results of the overall structural response as well as the formation of damage in the infilled wall. Comparison of the numerical and experimental results highlights the valuable contribution of numerical simulations in the study and design of infilled frames. As damage of the infill masonry may occur in-plane due to the interaction as well as out-of-plane due to the low vertical load, both directions of loading are investigated.},
  language  = {en}
}
@inproceedings{MarkinkovicButenwegPaveseetal.2020,
  author    = {Markinkovic, Marko and Butenweg, Christoph and Pavese, A. and Lanese, I. and Hoffmeister, B. and Pinkawa, M. and Vulcu, C. and Bursi, O. and Nardin, C. and Paolacci, F. and Quinci, G. and Fragiadakis, M. and Weber, F. and Huber, P. and Renault, P. and G{\"u}ndel, M. and Dyke, S. and Ciucci, M. and Marino, A.},
  title     = {Investigation of the seismic behaviour of structural and nonstructural components in industrial facilities by means of shaking table tests},
  series = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)},
  booktitle = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)},
  isbn      = {978-3-86359-729-0},
  pages     = {159 -- 172},
  year      = {2020},
  language  = {en}
}
@inproceedings{ReisgenSchleserSchoeneetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Schoene, Jens and Hegger, Josef and Gallwoszus, J{\"o}rg and Feldmann, Markus and Kopp, Maik and G{\"u}ndel, Max},
  title     = {Investigation on bond mechanisms of innovative small-scale shear connectors between steel and concrete},
  series = {Bond in concrete 2012. Vol. 2. Bond in new materials and under severe conditions},
  booktitle = {Bond in concrete 2012. Vol. 2. Bond in new materials and under severe conditions},
  editor    = {Cairns, John W.},
  publisher = {Publisher creations},
  address   = {Manerbio, Brescia},
  isbn      = {978-88-907078-3-4},
  pages     = {893 -- 898},
  year      = {2012},
  language  = {en}
}
@inproceedings{SchoppHeuermannHoltrup2014,
  author    = {Schopp, Christoph and Heuermann, Holger and Holtrup, S.},
  title     = {Investigation on efficacy optimization of RF-driven automotive D-lamps},
  series = {44th European Microwave Conference (EuMC),2014, Rome},
  booktitle = {44th European Microwave Conference (EuMC),2014, Rome},
  doi       = {10.1109/EuMC.2014.6986645},
  pages     = {1154 -- 1157},
  year      = {2014},
  language  = {en}
}
@inproceedings{WeissHeslenfeldSaeweetal.2022,
  author    = {Weiss, Christian and Heslenfeld, Jonas and Saewe, Jasmin Kathrin and Bremen, Sebastian and H{\"a}fner, Constantin Leon},
  title     = {Investigation on the influence of powder humidity in Laser Powder Bed Fusion (LPBF)},
  series = {Procedia CIRP},
  volume    = {111},
  booktitle = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2022.08.102},
  pages     = {115 -- 120},
  year      = {2022},
  abstract  = {In the Laser Powder Bed Fusion (LPBF) process, parts are built out of metal powder material by exposure of a laser beam. During handling operations of the powder material, several influencing factors can affect the properties of the powder material and therefore directly influence the processability during manufacturing. Contamination by moisture due to handling operations is one of the most critical aspects of powder quality. In order to investigate the influences of powder humidity on LPBF processing, four materials (AlSi10Mg, Ti6Al4V, 316L and IN718) are chosen for this study. The powder material is artificially humidified, subsequently characterized, manufactured into cubic samples in a miniaturized process chamber and analyzed for their relative density. The results indicate that the processability and reproducibility of parts made of AlSi10Mg and Ti6Al4V are susceptible to humidity, while IN718 and 316L are barely influenced.},
  language  = {en}
}
@inproceedings{HeinzOertelBung2010,
  author    = {Heinz, G. and Oertel, Mario and Bung, Daniel B.},
  title     = {Investigations on a cooling water system for a gas tubine facility concerning air vortexes and sediment transport},
  series = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010},
  booktitle = {Hydraulic structures: useful water harvesting systems or relics? : Third International Junior Researcher and Engineer Workshop on Hydraulic Structures (IJREWHS'10) : Edinburgh, Scotland, U.K., 2-3 May 2010},
  editor    = {Janssen, Robert},
  publisher = {School of Civil Engineering, The University of Queensland},
  address   = {Brisbane},
  organization    = {International Junior Researcher and Engineer Workshop on Hydraulic Structures <3, 2010, Edinburgh>},
  isbn      = {9781742720159},
  pages     = {109 -- 116},
  year      = {2010},
  language  = {en}
}
@inproceedings{Sauerborn2011,
  author    = {Sauerborn, Markus},
  title     = {Investigations to the influence of clouds and aerosols to the haze of the sunshape},
  series = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain},
  booktitle = {SolarPACES 2011 : concentrating solar power and chemical energy systems : 20 - 23 September, 2011, Granada, Spain},
  address   = {Granada},
  pages     = {1 CD-ROM},
  year      = {2011},
  language  = {en}
}
@inproceedings{BegingPoghossianMlyneketal.2010,
  author    = {Beging, Stefan and Poghossian, Arshak and Mlynek, D. and Hataihimakul, S. and Pedraza, A. and Dhawan, S. and Laube, N. and Kleinen, L. and Baldsiefen, G. and Busch, H. and Sch{\"o}ning, Michael Josef},
  title     = {Ion-selective sensors for the determination of the risk of urinary stone formation},
  series = {Micro- and Nanosystems in biochemical diagnosis : Principles and applications},
  booktitle = {Micro- and Nanosystems in biochemical diagnosis : Principles and applications},
  address   = {Warsaw},
  pages     = {74 -- 80},
  year      = {2010},
  language  = {en}
}
@inproceedings{BrockmannSultanowCzarnecki2019,
  author    = {Brockmann, Carsten and Sultanow, Eldar and Czarnecki, Christian},
  title     = {Is enterprise architecture still relevant in the digital age?},
  series = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge},
  booktitle = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge},
  editor    = {Draude, Claude and Lange, Martin and Sick, Bernhard},
  publisher = {K{\"o}llen},
  address   = {Bonn},
  isbn      = {9783885796893},
  issn      = {1617-5468},
  doi       = {10.18420/inf2019_ws01},
  pages     = {21 -- 21},
  year      = {2019},
  language  = {en}
}
@inproceedings{KolditzAlbinAlbrachtetal.2016,
  author    = {Kolditz, Melanie and Albin, Thivaharan and Albracht, Kirsten and Br{\"u}ggemann, Gert-Peter and Abel, Dirk},
  title     = {Isokinematic leg extension training with an industrial robot},
  series = {6th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics (BioRob) June 26-29, 2016. UTown, Singapore},
  booktitle = {6th IEEE RAS/EMBS International Conference on Biomedical Robotics and Biomechatronics (BioRob) June 26-29, 2016. UTown, Singapore},
  doi       = {10.1109/BIOROB.2016.7523750},
  pages     = {950 -- 955},
  year      = {2016},
  language  = {de}
}
@inproceedings{BeckerHoefkenSchuetzetal.2016,
  author    = {Becker, Sebastian and H{\"o}fken, Hans-Wilhelm and Sch{\"u}tz, Philip and Schuba, Marko},
  title     = {IT-forensische Erkennung modifizierter Android-Apps},
  series = {Proceedings of DACH Security 2016, Klagenfurt, Austria, September 2016},
  booktitle = {Proceedings of DACH Security 2016, Klagenfurt, Austria, September 2016},
  editor    = {Schartner, P.},
  pages     = {120 -- 125},
  year      = {2016},
  abstract  = {Malware auf Smartphones ist ein Problem, dem auch Strafverfolgungsbeh{\"o}rden immer h{\"a}ufiger gegen{\"u}berstehen. Insbesondere Telefone, bei denen potentiell schadhafte Apps zu einem finanziellen Schaden gef{\"u}hrt haben, finden sich auf den Schreibtischen der Polizei wieder. Dabei m{\"u}ssen die Ermittler m{\"o}glichst schnell und gezielt erkennen k{\"o}nnen, ob eine App tats{\"a}chlich schadhaft manipuliert wurde, was manipuliert wurde und mit wem die App kommuniziert. Klassische Malware-Erkennungsverfahren helfen zwar bei der generellen Erkennung schadhafter Software, sind aber f{\"u}r die polizeiliche Praxis nicht geeignet. Dieses Paper stellt ein Programm vor, welches gerade die forensischen Fragestellungen ber{\"u}cksichtigt und so f{\"u}r den Einsatz in der Strafverfolgung in Frage kommt.},
  language  = {de}
}
@inproceedings{HartungHillgaertnerSchmitzetal.2014,
  author    = {Hartung, Frank and Hillg{\"a}rtner, Michael and Schmitz, G{\"u}nter and Schuba, Marko and Adolphs, Fabian and Hoffend, Jens and Theis, Jochen},
  title     = {IT-Sicherheit im Automobil},
  series = {AmE 2014 : Automotive meets Electronics, Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund. (GMM-Fachbericht ; 78)},
  booktitle = {AmE 2014 : Automotive meets Electronics, Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund. (GMM-Fachbericht ; 78)},
  publisher = {VDE-Verl.},
  address   = {Berlin},
  organization    = {VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)},
  isbn      = {978-3-8007-3580-8},
  pages     = {CD-ROM},
  year      = {2014},
  language  = {de}
}
@inproceedings{KetelhutGoellBraunsteinetal.2019,
  author    = {Ketelhut, Maike and G{\"o}ll, Fabian and Braunstein, Bjoern and Albracht, Kirsten and Abel, Dirk},
  title     = {Iterative learning control of an industrial robot for neuromuscular training},
  series = {2019 IEEE Conference on Control Technology and Applications},
  booktitle = {2019 IEEE Conference on Control Technology and Applications},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-1-7281-2767-5 (ePub)},
  doi       = {10.1109/CCTA.2019.8920659},
  pages     = {7 Seiten},
  year      = {2019},
  abstract  = {Effective training requires high muscle forces potentially leading to training-induced injuries. Thus, continuous monitoring and controlling of the loadings applied to the musculoskeletal system along the motion trajectory is required. In this paper, a norm-optimal iterative learning control algorithm for the robot-assisted training is developed. The algorithm aims at minimizing the external knee joint moment, which is commonly used to quantify the loading of the medial compartment. To estimate the external knee joint moment, a musculoskeletal lower extremity model is implemented in OpenSim and coupled with a model of an industrial robot and a force plate mounted at its end-effector. The algorithm is tested in simulation for patients with varus, normal and valgus alignment of the knee. The results show that the algorithm is able to minimize the external knee joint moment in all three cases and converges after less than seven iterations.},
  language  = {en}
}
@inproceedings{FateriGebhardt2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Jewelry fabrication via selective laser melting of glass},
  series = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  booktitle = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  isbn      = {978-0-7918-4583-7},
  doi       = {10.1115/ESDA2014-20380},
  pages     = {V001T06A005},
  year      = {2014},
  abstract  = {Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies applicable for producing complex geometries which are typically expensive or difficult to fabricate using conventional methods. This process has been extensively investigated experimentally for various metals and the fabrication process parameters have been established for different applications; however, fabricating 3D glass objects using SLM technology has remained a challenge so far although it could have many applications. This paper presents a summery on various experimental evaluations of a material database incorporating the build parameters of glass powder using the SLM process for jewelry applications.},
  language  = {en}
}
@inproceedings{Gligorevic2002,
  author    = {Gligorevic, Snjezana},
  title     = {Joint channel estimation and equalization for fast time-variant multipath channels},
  series = {Proceedings / 13th IEEE International Symposium on Personal, Indoor and Mobile Radio Communications : PIMRC 2002 : Lisboa, Portugal, September 15 - 18, 2002},
  booktitle = {Proceedings / 13th IEEE International Symposium on Personal, Indoor and Mobile Radio Communications : PIMRC 2002 : Lisboa, Portugal, September 15 - 18, 2002},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {0-7803-7589-0},
  pages     = {1127 -- 1130},
  year      = {2002},
  language  = {en}
}
@inproceedings{HadinejadMahramGligorevicRitscher2002,
  author    = {Hadinejad-Mahram, Hafez and Gligorevic, Snjezana and Ritscher, Matthias},
  title     = {Joint iterative channel estimation and parallel interference cancellation for coded DS-CDMA},
  series = {Proceeding of the International Conference on Telecommunications 2002 : [Beijing, 23 - 26 June 2002]. Vol. 2},
  booktitle = {Proceeding of the International Conference on Telecommunications 2002 : [Beijing, 23 - 26 June 2002]. Vol. 2},
  organization    = {Institute of Electrical and Electronics Engineers},
  pages     = {566 -- 570},
  year      = {2002},
  language  = {en}
}
@inproceedings{BraunsteinGoldmannAlbrachtetal.2013,
  author    = {Braunstein, Bjoern and Goldmann, Jan-Peter and Albracht, Kirsten and Sanno, Maximilian and Willwacher, Steffen and Heinrich, Kai and Herrmann, Volker and Br{\"u}ggemann, Gert-Peter},
  title     = {Joint specific contribution of mechanical power and work during acceleration and top speed in elite sprinters},
  series = {31 International Conference on Biomechanics in Sports, Taipei, Taiwan, July 07 - July 22, 2013},
  booktitle = {31 International Conference on Biomechanics in Sports, Taipei, Taiwan, July 07 - July 22, 2013},
  issn      = {1999-4168},
  year      = {2013},
  language  = {en}
}
@inproceedings{GoldmannBraunsteinHeinrichetal.2015,
  author    = {Goldmann, Jan-Peter and Braunstein, Bjoern and Heinrich, Kai and Sanno, Maximilian and St{\"a}udle, Benjamin and Ritzdorf, Wolfgang and Br{\"u}ggemann, Gert-Peter and Albracht, Kirsten},
  title     = {Joint work of the take-off leg during elite high jump},
  series = {Proceedings of the 33th International Conference on Biomechanics in Sports (ISBS)},
  booktitle = {Proceedings of the 33th International Conference on Biomechanics in Sports (ISBS)},
  pages     = {3 S.},
  year      = {2015},
  language  = {en}
}
@inproceedings{UibelBlass2013,
  author    = {Uibel, Thomas and Blaß, Hans-Joachim},
  title     = {Joints with Dowel Type Fasteners in CLT structures},
  series = {Focus solid timber solutions : European Conference on Cross Laminated Timber (CLT); May 21-22, 2013, Graz University of Technology, Austria},
  booktitle = {Focus solid timber solutions : European Conference on Cross Laminated Timber (CLT); May 21-22, 2013, Graz University of Technology, Austria},
  organization    = {European Conference on Cross Laminated Timber <2013, Graz>},
  isbn      = {978-1-85790-181-8 ; 1-85790-181-9},
  pages     = {119 -- 134},
  year      = {2013},
  language  = {en}
}
@inproceedings{Hoepner2008,
  author    = {Hoepner, Gert},
  title     = {Jurorenstatement - Junioren zeigen sich aggressiv},
  organization    = {DDV Deutscher Dialogmarketing Verband e. V.},
  year      = {2008},
  abstract  = {Statement zu den Einreichung des DDP 2008},
  subject      = {Deutscher Direktmarketing-Verband},
  language  = {de}
}
@inproceedings{OberlaenderReisertKirchneretal.2013,
  author    = {Oberl{\"a}nder, Jan and Reisert, Steffen and Kirchner, Patrick and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Kalorimetrische Gassensoren zur H2O2-Detektion in aseptischen Sterilisationsprozessen},
  series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  organization    = {Dresdner Sensor-Symposium <11, 2013>},
  isbn      = {978-3-9813484-5-3},
  pages     = {234 -- 238},
  year      = {2013},
  language  = {de}
}
@inproceedings{PinnekampMueller2006,
  author    = {Pinnekamp, Johannes and M{\"u}ller, Karsten},
  title     = {Kanalisation und Gew{\"a}sserschutz},
  series = {7. K{\"o}lner Kanal Kolloquium : 06. und 07. September 2006 im Maternushaus, K{\"o}ln / hrsg. von Johannes Pinnekamp. Aachener Schriften zur Stadtentw{\"a}sserung. Bd. 9},
  booktitle = {7. K{\"o}lner Kanal Kolloquium : 06. und 07. September 2006 im Maternushaus, K{\"o}ln / hrsg. von Johannes Pinnekamp. Aachener Schriften zur Stadtentw{\"a}sserung. Bd. 9},
  publisher = {Ges. zur F{\"o}rderung der Siedlungswasserwirtschaft an der RWTH Aachen},
  address   = {Aachen},
  isbn      = {3-938996-02-1},
  pages     = {1/1 -- 1/16},
  year      = {2006},
  language  = {de}
}
@inproceedings{AbelBoninAlbrachtetal.2010,
  author    = {Abel, Thomas and Bonin, Dominik and Albracht, Kirsten and Zeller, Sebastian and Br{\"u}ggemann, Gert-Peter and Burkett, Brendan and Str{\"u}der, Heiko K.},
  title     = {Kinematic profile of the elite handcyclist},
  series = {28th International Conference on Biomechanics in Sports, Marquette, Michigan, USA, July 19 - 23, 2010},
  booktitle = {28th International Conference on Biomechanics in Sports, Marquette, Michigan, USA, July 19 - 23, 2010},
  issn      = {1999-4168},
  pages     = {140 -- 141},
  year      = {2010},
  language  = {en}
}
@inproceedings{ReisgenSchleserStieglitz2009,
  author    = {Reisgen, Uwe and Schleser, Markus and Stieglitz, Anja},
  title     = {Kleben im Schienenfahrzeugbau},
  series = {Die Verbindungs-Spezialisten 2009 : Große Schweißtechnische Tagung ; Forschungsforum, Industrieforum, Studentenkongress, Handwerkerforum ; Vortr{\"a}ge der Veranstaltung in Essen vom 14. bis 19. September 2009. DVS-Berichte. 258},
  booktitle = {Die Verbindungs-Spezialisten 2009 : Große Schweißtechnische Tagung ; Forschungsforum, Industrieforum, Studentenkongress, Handwerkerforum ; Vortr{\"a}ge der Veranstaltung in Essen vom 14. bis 19. September 2009. DVS-Berichte. 258},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {DVS - Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren e.V. ; Große Schweißtechnische Tagung <2009, Essen>},
  isbn      = {978-3-87155-584-8},
  pages     = {182 -- 186},
  year      = {2009},
  language  = {de}
}
@inproceedings{ReisgenSchleserEssersetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Essers, Marc and Thiele, Regina and Schiebahn, Alexander},
  title     = {Klebstofffixiertes R{\"u}hrreibschweißen von d{\"u}nnen Aluminiumblechen},
  series = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  booktitle = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {Große Schweißtechnische Tagung <2012, Saarbr{\"u}cken> ; Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren},
  isbn      = {978-3-87155-593-0},
  pages     = {20 -- 25},
  year      = {2012},
  language  = {de}
}
@inproceedings{BagheriSchleupenDahmannetal.2016,
  author    = {Bagheri, Mohsen and Schleupen, Josef and Dahmann, Peter and Kallweit, Stephan},
  title     = {Kletternde Wartungsplattform f{\"u}r die wetterunabh{\"a}ngige Instandhaltung von Rotorbl{\"a}ttern an Windenergieanlagen - SMART},
  series = {AKIDA 2016 Aachener Kolloquium f{\"u}r Instandhaltung, Diagnose und Anlagen{\"u}berwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen},
  booktitle = {AKIDA 2016 Aachener Kolloquium f{\"u}r Instandhaltung, Diagnose und Anlagen{\"u}berwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen},
  pages     = {21 Folien},
  year      = {2016},
  abstract  = {In Deutschland liegt der Anteil der Windkraft an der Gesamtstromerzeugung bei 13,3\% mit mehr als 25.000 installierten Windenergieanlagen (WEA). Weltweit erf{\"a}hrt die Windbranche ein rasantes Wachstum. Indien und China berichten eine j{\"a}hrliche Wachstumsrate an Neuinstallationen von 45\%. Die Technologie zur Erzeugung elektrischer Energie aus Windkraft ist noch vergleichsweise jung. Durch die weltweit steigende Anzahl an Windenergieanlagen w{\"a}chst zunehmend der Bedarf an innovativen Wartungsl{\"o}sungen. Komponenten wie Generator oder Getriebe sind inzwischen weitestgehend ausgereift. Der Fokus richtet sich zunehmend auf die wesentliche Kernkomponente - die Rotorbl{\"a}tter. Industriekletterer inspizieren die Rotorbl{\"a}tter oder T{\"u}rme i.d.R. in einem zwei Jahres Rhythmus. Sie werden zunehmend durch Seilarbeitsb{\"u}hnen unterst{\"u}tzt. F{\"u}r gr{\"o}ßere Reparaturen kommen Kr{\"a}ne zum Einsatz, mit denen das Rotorblatt f{\"u}r die Instandhaltung demontiert wird. Die Standardinspektion besteht aus Sicht- und Klopfpr{\"u}fung der Rotorblattoberfl{\"a}che und ist nur bei sehr ruhiger Wetterlage durchf{\"u}hrbar. Seit September 2014 wird das Forschungsprojekt SMART (Scanning, Monitoring, Analysis, Repair and Transportation), Entwicklung einer Wartungsplattform f{\"u}r WEA, vom BMWi gef{\"o}rdert. Das Konsortium besteht aus zwei Firmen und der Fachhochschule Aachen. Die SMART-Anlage klettert reibschl{\"u}ssig am Turm der WEA mittels speziellen Kettenfahrwerken (Abbildung) auf- und abw{\"a}rts. Ein ringf{\"o}rmiges Spannsystems, basierend auf dem Konzept der „N{\"u}rnberger"-Schere, erzeugt die erforderliche Anpresskraft f{\"u}r den Kletterprozess. Wettergesch{\"u}tzte Arbeitskabinen erm{\"o}glichen die ganzj{\"a}hrige Instandhaltung von Rotorbl{\"a}ttern und ebenso T{\"u}rmen. Dadurch k{\"o}nnen Wartungsarbeiten auf 24 Stunden am Tag ausgeweitet werden. Der kombinierte Einsatz (Sensorfusion) bildgebender Messtechnik wie Thermografie, Ultraschall, und Terahertz in der Arbeitskabine kann die Dokumentation, Effizienz und Qualit{\"a}t der Instandhaltungsarbeiten erheblich verbessern. Langfristiges Ziel von SMART ist ein Condition Monitoring f{\"u}r Rotorbl{\"a}tter und T{\"u}rme auf Basis digitalisierter dreidimensionaler Volumenscans. Der kooperative Einsatz mit UAVs erweitert die Instandhaltungsstrategie. UAVs erm{\"o}glichen die schnelle, kosteng{\"u}nstige globale optische Inspektion von Rotorblattoberfl{\"a}chen zur Detektion potentieller Fehlstellen. Der „Proof-of-Concept" Meilenstein wurde mit der Demonstration eines funktionsf{\"a}higen Modells im Dezember 2015 erfolgreich abgeschlossen.},
  language  = {de}
}
@inproceedings{PisarczykRitzSachtleben2013,
  author    = {Pisarczyk, Rafael and Ritz, Thomas and Sachtleben, Johanna},
  title     = {KMU-taugliche Modelle zur Entwicklung gebrauchstauglicher mobiler Unternehmenssoftware},
  series = {Mensch \& Computer 2013 - Workshopband : 13. fach{\"u}bergreifende Konferenz f{\"u}r interaktive und kooperative Medien},
  booktitle = {Mensch \& Computer 2013 - Workshopband : 13. fach{\"u}bergreifende Konferenz f{\"u}r interaktive und kooperative Medien},
  editor    = {Boll-Westermann, Susanne},
  publisher = {Oldenbourg},
  address   = {M{\"u}nchen},
  isbn      = {978-3-486-77855-7 (Print)},
  doi       = {10.1524/9783486781236},
  pages     = {29 -- 38},
  year      = {2013},
  language  = {de}
}
@inproceedings{StaatSzelinskiHeitzer2001,
  author    = {Staat, Manfred and Szelinski, E. and Heitzer, Michael},
  title     = {Kollapsanalyse von l{\"a}ngsfehlerbehafteten Rohren und Beh{\"a}ltern},
  year      = {2001},
  abstract  = {Es werden verbesserte Kollapsanalysen von dickwandigen, mit axialen Oberfl{\"a}chenfehlern behafteten Rohren und Beh{\"a}ltern vorgeschlagen.},
  subject      = {Druckbeh{\"a}lter},
  language  = {de}
}
@inproceedings{Overkamp2009,
  author    = {Overkamp, Stefan},
  title     = {Kombination von Desktop GIS, Geodatenbank und Internet-GIS am Beispiel von Manifold System 8.0, PostgreSQL 8.3 und Adobe Flex},
  year      = {2009},
  abstract  = {Dipl.-Ing. Stefan Overkamp - GISWORKS GbR, Velbert. 11 S. (S. 7-17). Beitrag zum 2. Aachener Softwaretag in der Wasserwirtschaft <2, 2009, Aachen> Aus der Gliederung: 1 Geoinformationssysteme 2 Anforderungen an eine kommunale Geodateninfrastruktur (GDI) 3 Komponenten einer GDI 3.1 Geodatenmanagement 3.2 Geodatenhaltung 3.3 High-End-GIS 3.4 intraGIS 4 GISWORKS 5 Weiterf{\"u}hrende Informationen},
  subject      = {Geoinformationssystem},
  language  = {de}
}
@inproceedings{WernerMansourRateikeetal.2011,
  author    = {Werner, Frederik and Mansour, Ahmed and Rateike, Franz-Matthias and Schusser, Sebastian and Wagner, Torsten and Yoshinobu, Tatsuo and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Kompakter Aufbau eines lichtadressierbaren potentiometrischen Sensors mit verfahrbarem Diodenlaser},
  series = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43},
  booktitle = {10. Dresdner Sensor-Symposium : Dresden, 5. - 7. Dezember 2011 ; miniaturisierte analytische Verfahren, Hochtemperatur-Sensoren, Sensoren f{\"u}r Bioprozess- und Verfahrenstechnik, Sensoren f{\"u}r die Medizin, Chemische Verfahrenstechnik, Lebensmittelanalytik, innovative Sensorl{\"o}sungen, Sensoren f{\"u}r die Wasserqualit{\"a}t, Selbst{\"u}berwachung / Gerald Gerlach ... (Hg.) Dresdner Beitr{\"a}ge zur Sensorik. 43},
  editor    = {Gerlach, Gerald},
  publisher = {TUDpress},
  address   = {Dresden},
  isbn      = {978-3-942710-53-4},
  pages     = {277 -- 280},
  year      = {2011},
  language  = {de}
}
@inproceedings{BudaWollert2008,
  author    = {Buda, Aurel and Wollert, J{\"o}rg},
  title     = {Kompensation von Fading und Koexistenzproblemen in IEEE 802.15.4 Netzwerken durch Diversit{\"a}t : die Kombination macht's m{\"o}glich},
  series = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  booktitle = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Automatisierungskongress <2008, Baden-Baden>},
  isbn      = {978-3-18-092032-0},
  pages     = {139 -- 142},
  year      = {2008},
  language  = {de}
}
@inproceedings{BillerbeckLadwigSaldenetal.2015,
  author    = {Billerbeck, Katrin and Ladwig, Tina and Salden, Peter and Barnat, Miriam},
  title     = {Kompetenzen visualisieren als Notenersatz? Ann{\"a}herung an eine didaktische Herausforderung},
  series = {Wie viel (Grundlagen) Wissen braucht technische Bildung? : Wege zu technischer Bildung : Referate der 9. Ingenieurp{\"a}dagogischen Regionaltagung 2014 an der Universit{\"a}t Siegen, 6.-8. November 2014},
  booktitle = {Wie viel (Grundlagen) Wissen braucht technische Bildung? : Wege zu technischer Bildung : Referate der 9. Ingenieurp{\"a}dagogischen Regionaltagung 2014 an der Universit{\"a}t Siegen, 6.-8. November 2014},
  editor    = {Kammasch, Gudrun},
  publisher = {Berlin},
  address   = {IPW},
  isbn      = {978-3-00-049835-0},
  pages     = {57 -- 63},
  year      = {2015},
  language  = {de}
}
@inproceedings{ReisgenSchleserHarmsetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Harms, Alexander and Schiebahn, Alexander},
  title     = {Konduktiv unterst{\"u}tztes R{\"u}hrreibschweißen an Stahl- und Aluminiumwerkstoffen},
  series = {DVS congress 2010 : Große Schweißtechnische Tagung ; Studentenkongress ; Statusseminar "Schneidtechnik" ; Abschlusskolloquium zum AiF-Forschungscluster "Integration des R{\"u}hrreibschweißens in Fertigungsprozessketten" ; Vortr{\"a}ge der Veranstaltung in N{\"u}rnberg am 27. und 28. September 2010. (DVS-Berichte ; 267)},
  booktitle = {DVS congress 2010 : Große Schweißtechnische Tagung ; Studentenkongress ; Statusseminar "Schneidtechnik" ; Abschlusskolloquium zum AiF-Forschungscluster "Integration des R{\"u}hrreibschweißens in Fertigungsprozessketten" ; Vortr{\"a}ge der Veranstaltung in N{\"u}rnberg am 27. und 28. September 2010. (DVS-Berichte ; 267)},
  publisher = {DVS Media},
  address   = {D{\"u}sseldorf},
  organization    = {Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren ; Große Schweißtechnische Tagung <2010, N{\"u}rnberg>},
  isbn      = {978-3-87155-592-3},
  pages     = {394 -- 398},
  year      = {2010},
  language  = {de}
}
@inproceedings{SchuermannKellerWollert2009,
  author    = {Sch{\"u}rmann, Volker and Keller, Alex and Wollert, J{\"o}rg},
  title     = {Konvergenz von drahtlosen und drahtgebundenen Kommunikationstechnologien in der Geb{\"a}udeautomation},
  series = {Wireless technologies : von der Technologie zur Anwendung ; 11. Kongress, 29. - 30. September 2009, Stuttgart / [11. Wireless-Technologies-Kongress]. (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 800)},
  booktitle = {Wireless technologies : von der Technologie zur Anwendung ; 11. Kongress, 29. - 30. September 2009, Stuttgart / [11. Wireless-Technologies-Kongress]. (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 800)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Wireless-Technologies-Kongress <11, 2009, Stuttgart>},
  isbn      = {978-3-18-380010-0},
  pages     = {197 -- 205},
  year      = {2009},
  language  = {de}
}
@inproceedings{MollKoehlerWolf2019,
  author    = {Moll, Florian and K{\"o}hler, Klemens and Wolf, Martin},
  title     = {Konzeption von IT-Sicherheitsl{\"o}sungen unter ethischen Gesichtspunkten am Beispiel einer Monitoring-App f{\"u}r mobile Endger{\"a}te},
  series = {Angewandte Forschung in der Wirtschaftsinformatik 2019 : Tagungsband zur 32. AKWI-Jahrestagung},
  booktitle = {Angewandte Forschung in der Wirtschaftsinformatik 2019 : Tagungsband zur 32. AKWI-Jahrestagung},
  publisher = {mana-Buch},
  address   = {Heide},
  isbn      = {978-3-944330-62-4},
  pages     = {61 -- 72},
  year      = {2019},
  abstract  = {Die steigende Popularit{\"a}t von mobilen Endger{\"a}ten im privaten und gesch{\"a}ftlichen Umfeld geht mit einem Anstieg an Sicherheitsl{\"u}cken und somit potentiellen Angriffsfl{\"a}chen einher. Als ein Element der technischen und organisatorischen Maßnahmen zum Schutz eines Netzwerkes k{\"o}nnen Monitoring-Apps dienen, die unerw{\"u}nschtes Verhalten und Angriffe erkennen. Die automatisierte {\"U}berwachung von Endger{\"a}ten ist jedoch rechtlich und ethisch komplex. Dies in Kombination mit einer hohen Sensibilit{\"a}t der Nutzer und Nutzerinnen dieser Ger{\"a}te in Bezug auf Privatsph{\"a}re, kann zu einer geringen Akzeptanz und Compliance f{\"u}hren. Eine datenschutzrechtlich und ethisch einwandfreie Konzeption solcher Apps bereits im Designprozess f{\"u}hrt zu h{\"o}herer Akzeptanz und verbessert so die Effizienz. Diese Analyse beschreibt M{\"o}glichkeiten zur Umsetzung.},
  language  = {de}
}
@inproceedings{Hoffschmidt2011,
  author    = {Hoffschmidt, Bernhard},
  title     = {Kooperationen und Ziele am Standort J{\"u}lich},
  series = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster},
  booktitle = {Forschung und Entwicklung f{\"u}r solarthermische Kraftwerke : 14. K{\"o}lner Sonnenkolloquium Mittwoch, 13. Juli 2011, im Auditorium des Campus J{\"u}lich der FH Aachen : Kurzfassungen der Vortr{\"a}ge und Poster},
  publisher = {DLR},
  address   = {K{\"o}ln},
  pages     = {4 S.},
  year      = {2011},
  language  = {de}
}
@inproceedings{RitzFuchs2008,
  author    = {Ritz, Thomas and Fuchs, Britta},
  title     = {Kosten-Nutzen-Bewertungen bei mobilen Anwendungen},
  series = {Mobile und Ubiquit{\"a}re Informationssysteme - Technologien, Prozesse, Marktfahigkeit. Proceedings zur 3. Konferenz Mobile und Ubiquit{\"a}re Informationssysteme (MMS 2008) 26. - 28. Februar 2008, M{\"u}nchen, Germany. - (GI-Edition : Proceedings ; 123) Breitner, Michael H. [Hrsg.]},
  booktitle = {Mobile und Ubiquit{\"a}re Informationssysteme - Technologien, Prozesse, Marktfahigkeit. Proceedings zur 3. Konferenz Mobile und Ubiquit{\"a}re Informationssysteme (MMS 2008) 26. - 28. Februar 2008, M{\"u}nchen, Germany. - (GI-Edition : Proceedings ; 123) Breitner, Michael H. [Hrsg.]},
  editor    = {Breitner, Michael},
  publisher = {Ges. f{\"u}r Informatik},
  address   = {Bonn},
  isbn      = {978-3-88579-217-8},
  pages     = {164 -- 177},
  year      = {2008},
  language  = {de}
}
@inproceedings{IlleSchrammAdametal.2009,
  author    = {Ille, Fabian and Schramm, S. and Adam, M. and Backes, K. and Anthrakidis, Anette and Faber, Christian},
  title     = {Kraft-W{\"a}rme-K{\"a}lte-Kopplung im Leistungsbereich in 10kW mit periodisch arbeitender Sorptionsmaschine},
  series = {DKV-Tagungsbericht. 35,2,1. Deutsche K{\"a}lte-Klima-Tagung 2008 Ulm},
  booktitle = {DKV-Tagungsbericht. 35,2,1. Deutsche K{\"a}lte-Klima-Tagung 2008 Ulm},
  publisher = {Dt. K{\"a}lte- und Klimatechnischer Verein},
  address   = {Hannover},
  isbn      = {978-3-932715-44-0},
  pages     = {305 -- 320},
  year      = {2009},
  language  = {de}
}
@inproceedings{SchneckenburgerFranzenGligorevicetal.2011,
  author    = {Schneckenburger, N. and Franzen, N. and Gligorevic, Snjezana and Schnell, M.},
  title     = {L-band compatibility of LDACS1},
  series = {IEEE/AIAA 30th Digital Avionics Systems Conference (DASC) : 16 - 20 Oct. 2011, Seattle, Wash.},
  booktitle = {IEEE/AIAA 30th Digital Avionics Systems Conference (DASC) : 16 - 20 Oct. 2011, Seattle, Wash.},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {978-1-61284-797-9},
  issn      = {2155-7195},
  pages     = {4C3-1 -- 4C3-11},
  year      = {2011},
  language  = {en}
}
@inproceedings{GligorevicSchneckenburgerFranzenetal.2011,
  author    = {Gligorevic, Snjezana and Schneckenburger, N. and Franzen, N. and Schnell, Michael and M{\"u}ller, S. and G{\"u}nzel, H.},
  title     = {L-Band compatibility of LDACS1},
  series = {3rd CEAS Air and Space Conference, 24 - 28 October 2011, Venezia, Italy},
  booktitle = {3rd CEAS Air and Space Conference, 24 - 28 October 2011, Venezia, Italy},
  organization    = {European Air and Space Conference <3, 2011, Venezia>},
  pages     = {1 -- 8},
  year      = {2011},
  language  = {en}
}
@inproceedings{SchnellFranzenGligorevic2010,
  author    = {Schnell, Michael and Franzen, Nico and Gligorevic, Snjezana},
  title     = {L-DACS1 laboratory demonstrator development and compatibility measurement set-up},
  series = {IEEE/AIAA 29th Digital Avionics Systems Conference (DASC) : 3 - 7 Oct. 2010, Salt Lake City, Utah},
  booktitle = {IEEE/AIAA 29th Digital Avionics Systems Conference (DASC) : 3 - 7 Oct. 2010, Salt Lake City, Utah},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {9781424466160 ; 9781424466184},
  pages     = {3E3-1 -- 3E3-11},
  year      = {2010},
  language  = {en}
}
@inproceedings{PoghossianBronderSchejaetal.2016,
  author    = {Poghossian, Arshak and Bronder, Thomas and Scheja, S. and Wu, Chunsheng and Metzger-Boddien, C. and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Label-free Electrostatic Detection of DNA Amplification by PCR Using Capacitive Field-effect Devices},
  series = {Procedia Engineering},
  volume    = {Vol. 168},
  booktitle = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2016.11.512},
  pages     = {514 -- 517},
  year      = {2016},
  abstract  = {A capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensor modified with a positively charged weak polyelectrolyte of poly(allylamine hydrochloride) (PAH)/single-stranded probe DNA (ssDNA) bilayer has been used for a label-free electrostatic detection of pathogen-specific DNA amplification via polymerase chain reaction (PCR). The sensor is able to distinguish between positive and negative PCR solutions, to detect the existence of target DNA amplicons in PCR samples and thus, can be used as tool for a quick verification of DNA amplification and the successful PCR process.},
  language  = {en}
}
@inproceedings{PoghossianBronderWuetal.2015,
  author    = {Poghossian, Arshak and Bronder, Thomas and Wu, Chunsheng and Sch{\"o}ning, Michael Josef},
  title     = {Label-free sensing of biomolecules by their intrinsic molecular charge using field-effect devices},
  series = {Semiconductor Micro- and Nanoelectonics : Proceedings of the tenth international conference, Yerevan, Armenia, September 11-13},
  booktitle = {Semiconductor Micro- and Nanoelectonics : Proceedings of the tenth international conference, Yerevan, Armenia, September 11-13},
  isbn      = {978-5-8084-1991-9},
  pages     = {61 -- 63},
  year      = {2015},
  language  = {en}
}
@inproceedings{ZischankHeidlerKernetal.2002,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Kern, Alexander and Metwally, I. A. and Wiesinger, J. and Seevers, M.},
  title     = {Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages},
  year      = {2002},
  abstract  = {In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between "floor" and "roof" in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived.},
  language  = {en}
}
@inproceedings{Hartz2004,
  author    = {Hartz, Thomas},
  title     = {LACASA - ein Instrument zur energetischen Analyse und Optimierung von Geb{\"a}uden mit Anlagentechnik},
  series = {14. Symposium Thermische Solarenergie : 12. bis 14. Mai 2004, Kloster Banz, Bad Staffelstein / OTTI-Kolleg Technik, Energie, Management},
  booktitle = {14. Symposium Thermische Solarenergie : 12. bis 14. Mai 2004, Kloster Banz, Bad Staffelstein / OTTI-Kolleg Technik, Energie, Management},
  publisher = {OTTI-Energie-Kolleg},
  address   = {Regensburg},
  pages     = {402 -- 406},
  year      = {2004},
  language  = {de}
}
@inproceedings{Mertens2000,
  author    = {Mertens, Josef},
  title     = {Laminar leading edges: manufacturing, contamination, and operational aspects - results from the German RaWid programme},
  year      = {2000},
  abstract  = {RaWid was the German national technology programme on transonic aerodynamics and supporting technologies, lasting from 1995 to 1998. One of the main topics was laminar wing development. Besides aerodynamic design work, many operational aspects were investigated. A manufacturing concept was developed to be applied to operational laminar wings and empennages. It was built in a large scale manufacturing demonstrator with the aerodynamic shape of a 1,5 m section of the A320 fin nose. Tolerances in shape and roughness fulfilled all requirements. The construction can easily be adapted to varying stiffness and strength requirements. Weight and manufacturing costs are comparable to common nose designs. The mock-up to be designed in ALTTA is based on this manufacturing principle. Another critical point is contamination of suction surfaces. Several tests were performed to investigate perforated titanium suction surfaces at realistic operational conditions: - a one year flight test with a suction plate in the stagnation area of the Airbus "Beluga" - a one year test of several suction plates in a ground test near the airport - a one year test of a working suction ground test installation at all weather conditions. No critical results were found. There is no long term suction degradation visible. Icing conditions and ground de-icing fluids used on airports did not pose severe problems. Some problems detected require only respection of weak design constraints.},
  subject      = {Laminare Str{\"o}mung},
  language  = {en}
}
@inproceedings{Wollert2006,
  author    = {Wollert, J{\"o}rg},
  title     = {Langzeitstatistische Untersuchungen zur Qualit{\"a}t von Funkkan{\"a}len f{\"u}r das industrielle Umfeld},
  series = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)},
  booktitle = {Wireless technologies : von der Technologie zur Anwendung : 8. Kongress, 27. - 28. September 2006, Dortmund ( J{\"o}rg Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 772)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {3-18-377210-8},
  pages     = {165 -- 176},
  year      = {2006},
  language  = {de}
}
@inproceedings{SeefeldtBauerDachwaldetal.2015,
  author    = {Seefeldt, Patric and Bauer, Waldemar and Dachwald, Bernd and Grundmann, Jan Thimo and Straubel, Marco and Sznajder, Maciej and T{\´o}th, Norbert and Zander, Martin E.},
  title     = {Large lightweight deployable structures for planetary defence: solar sail propulsion, solar concentrator payloads, large-scale photovoltaic power},
  series = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  booktitle = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  pages     = {24},
  year      = {2015},
  language  = {en}
}
@inproceedings{AdenackerGerhardsOttenetal.2021,
  author    = {Adenacker, J. and Gerhards, Benjamin and Otten, Christian and Schleser, Markus},
  title     = {Laserstrahlschweißen von Aluminium-Kupfer-Werkstoffkombinationen f{\"u}r die Elektromobilit{\"a}t},
  series = {DVS CONGRESS 2021},
  booktitle = {DVS CONGRESS 2021},
  publisher = {DVS Media GmbH},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-96144-146-4},
  pages     = {31 -- 38},
  year      = {2021},
  language  = {de}
}
@inproceedings{RingbeckBuxbaum1999,
  author    = {Ringbeck, Thorsten and Buxbaum, Bernd},
  title     = {Layoutoptimierte PMD-Strukturen f{\"u}r die schnelle 3D-Erfassung},
  series = {Messen in der Fertigung : 3D-Meßtechnik in Produktion und Entwicklung ; Fachtagung Optische Formerfassung ; Stuttgart, 5. - 6. Oktober 1999. - (Berichtsband / Deutsche Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung ; 70)},
  booktitle = {Messen in der Fertigung : 3D-Meßtechnik in Produktion und Entwicklung ; Fachtagung Optische Formerfassung ; Stuttgart, 5. - 6. Oktober 1999. - (Berichtsband / Deutsche Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung ; 70)},
  publisher = {DGfZP},
  address   = {Berlin},
  isbn      = {3-931381-30-7},
  pages     = {233 -- 243},
  year      = {1999},
  language  = {de}
}
@inproceedings{Wessling2007,
  author    = {Weßling, Matthias},
  title     = {Leadership Perspectives: Research Findings, Theories, Practical Experiences},
  year      = {2007},
  abstract  = {Leadership Perspectives: Research Findings, Theories, Practical Experiences: Results of Leadership Research and exemplarily application cases show the perspectives and consequences for leadership practice and the following requirements for executives in future.},
  subject      = {Leadership},
  language  = {en}
}
@inproceedings{WiesenEngemannLimpertetal.2018,
  author    = {Wiesen, Patrick and Engemann, Heiko and Limpert, Nicolas and Kallweit, Stephan},
  title     = {Learning by Doing - Mobile Robotics in the FH Aachen ROS Summer School},
  series = {European Robotics Forum 2018, TRROS18 Workshop},
  booktitle = {European Robotics Forum 2018, TRROS18 Workshop},
  pages     = {47 -- 58},
  year      = {2018},
  language  = {en}
}
@inproceedings{FerreinKallweitScholletal.2015,
  author    = {Ferrein, Alexander and Kallweit, Stephan and Scholl, Ingrid and Reichert, Walter},
  title     = {Learning to Program Mobile Robots in the ROS Summer School Series},
  series = {Proceedings 6th International Conference on Robotics in Education (RiE 15)},
  booktitle = {Proceedings 6th International Conference on Robotics in Education (RiE 15)},
  pages     = {6 S.},
  year      = {2015},
  abstract  = {The main objective of our ROS Summer School series is to introduce MA level students to program mobile robots with the Robot Operating System (ROS). ROS is a robot middleware that is used my many research institutions world-wide. Therefore, many state-of-the-art algorithms of mobile robotics are available in ROS and can be deployed very easily. As a basic robot platform we deploy a 1/10 RC cart that is wquipped with an Arduino micro-controller to control the servo motors, and an embedded PC that runs ROS. In two weeks, participants get to learn the basics of mobile robotics hands-on. We describe our teaching concepts and our curriculum and report on the learning success of our students.},
  language  = {en}
}
@inproceedings{PaslighFunkeRoethetal.2010,
  author    = {Pasligh, N. and Funke, D. and R{\"o}th, Thilo and Krack, R.},
  title     = {Leichtbau Quertrager als Stahlblech-Aluminiumdruckguss-Hybrid - Von der numerischen Berechnung bis zum realen Prototypen},
  series = {VDI BERICHTE},
  booktitle = {VDI BERICHTE},
  publisher = {VDI Verlag},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092107-5},
  pages     = {688 Seiten},
  year      = {2010},
  language  = {de}
}
@inproceedings{BudaWollert2011,
  author    = {Buda, Aurel and Wollert, J{\"o}rg},
  title     = {Leistungsbewertung von Ultra Wideband Funktechnologien nach ECMA 368 f{\"u}r den Einsatz in industriellen Kommunikationssystemen},
  series = {Kommunikation in der Automation : Magdeburg, 27. - 28.09.2011 ; 2. Jahreskolloquium Kommunikation in der Automation ; KOMMA 2011 / Ulrich Jumar ... (Hrsg.)},
  booktitle = {Kommunikation in der Automation : Magdeburg, 27. - 28.09.2011 ; 2. Jahreskolloquium Kommunikation in der Automation ; KOMMA 2011 / Ulrich Jumar ... (Hrsg.)},
  publisher = {ifak, Institut f{\"u}r Automation und Kommunikation e.V. Magdeburg an der Otto-von-Guericke-Universit{\"a}t Magdeburg},
  address   = {Magdeburg},
  organization    = {Jahreskolloquium Kommunikation in der Automation <2, 2011, Magdeburg>},
  isbn      = {978-3-940961-58-7},
  pages     = {1 CD-ROM},
  year      = {2011},
  language  = {de}
}
@inproceedings{Naujokat2012,
  author    = {Naujokat, Anke},
  title     = {Leon Battista Alberti and the consonance of old and new},
  series = {Proceedings of the 2nd International conference of the European Architectural History Network, Brussels 31 May - 2 June 2012},
  booktitle = {Proceedings of the 2nd International conference of the European Architectural History Network, Brussels 31 May - 2 June 2012},
  editor    = {Heynen, Hilde and Gosseye, Janina},
  publisher = {KVAB},
  address   = {Br{\"u}ssel},
  organization    = {European Architectural History Network},
  isbn      = {978-90-6569-102-6},
  pages     = {182 -- 184},
  year      = {2012},
  language  = {de}
}
@inproceedings{Pieper2018,
  author    = {Pieper, Martin},
  title     = {Lernzielorientierte Kurse und Stack Aufgaben in der Mathematikausbildung},
  series = {Beitr{\"a}ge zum Mathematikunterricht 2018 : Vortr{\"a}ge zur Mathematikdidaktik und zur Schnittstelle Mathematik/Mathematikdidaktik auf der gemeinsamen Jahrestagung GDM und DMV 2018 (52. Jahrestagung der Gesellschaft f{\"u}r Didaktik der Mathematik). Bd. 3},
  booktitle = {Beitr{\"a}ge zum Mathematikunterricht 2018 : Vortr{\"a}ge zur Mathematikdidaktik und zur Schnittstelle Mathematik/Mathematikdidaktik auf der gemeinsamen Jahrestagung GDM und DMV 2018 (52. Jahrestagung der Gesellschaft f{\"u}r Didaktik der Mathematik). Bd. 3},
  publisher = {WTM-Verlag},
  address   = {M{\"u}nster},
  isbn      = {978-3-95987-089-4},
  pages     = {1399 -- 1402},
  year      = {2018},
  language  = {de}
}
@inproceedings{BoernerFunkeHendricketal.2009,
  author    = {B{\"o}rner, Sebastian and Funke, Harald and Hendrick, P. and Recker, E.},
  title     = {LES of Jets In Cross-Flow and Application to the "Micromix" Hydrogen Combustion},
  series = {XIX International Symposium on Air Breathing Engines 2009 (ISABE 2009) : Proceedings of a meeting held 7-11 September 2009, Montreal, Canada},
  booktitle = {XIX International Symposium on Air Breathing Engines 2009 (ISABE 2009) : Proceedings of a meeting held 7-11 September 2009, Montreal, Canada},
  isbn      = {9781615676064},
  pages     = {1555 -- 1561},
  year      = {2009},
  language  = {en}
}
@inproceedings{FerreinNiemuellerSchifferetal.2013,
  author    = {Ferrein, Alexander and Niem{\"u}ller, Tim and Schiffer, Stefan and Lakemeyer, Gerhard},
  title     = {Lessons learnt from developing the embodied AI platform CAESAR for domestic service robotics},
  series = {Designing intelligent robots : reintegrating AI II ; papers from the AAAI spring symposium ; [held March 25 - 27, 2013 in Palo Alto, California, USA, on the campus of Stanford University]. (Technical Report / Association for the Advancement of Artificial Intelligence ; 2013,4)},
  booktitle = {Designing intelligent robots : reintegrating AI II ; papers from the AAAI spring symposium ; [held March 25 - 27, 2013 in Palo Alto, California, USA, on the campus of Stanford University]. (Technical Report / Association for the Advancement of Artificial Intelligence ; 2013,4)},
  editor    = {Boots, Byron},
  organization    = {American Association for Artificial Intelligence},
  isbn      = {9781577356011},
  pages     = {21 -- 26},
  year      = {2013},
  language  = {en}
}
@inproceedings{MuellerVeggianDehnhardtMills1975,
  author    = {M{\"u}ller-Veggian, Mattea and Dehnhardt, W. and Mills, J. S.},
  title     = {Levels in the closed neutron shell nucleus ¹⁴² Nd},
  series = {International Symposium on Highly Excited States in Nuclei held at J{\"u}lich from 23-26 September 1975 : proceedings; Vol. 1 Contributed papers},
  booktitle = {International Symposium on Highly Excited States in Nuclei held at J{\"u}lich from 23-26 September 1975 : proceedings; Vol. 1 Contributed papers},
  publisher = {Verlag des Forschungszentrums J{\"u}lich},
  address   = {J{\"u}lich},
  pages     = {51},
  year      = {1975},
  language  = {en}
}
@inproceedings{RosemannEggertVoigtetal.2012,
  author    = {Rosemann, Michael and Eggert, Mathias and Voigt, Matthias and Beverungen, Daniel},
  title     = {Leveraging Social Network Data for Analytical CRM Strategies - The Introduction of Social BI.},
  series = {ECIS 2012 Proceedings},
  booktitle = {ECIS 2012 Proceedings},
  pages     = {12 S.},
  year      = {2012},
  language  = {en}
}
@inproceedings{WagnerYoshinobuOttoetal.2006,
  author    = {Wagner, Torsten and Yoshinobu, T. and Otto, R. and Rao, C. and Molina, R. and Sch{\"o}ning, Michael Josef},
  title     = {Licht-adressierbare potentiometrische Sensorsysteme - Konzepte und Anwendungen},
  series = {Sensoren und Mess-Systeme 2006 : Vortr{\"a}ge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau},
  booktitle = {Sensoren und Mess-Systeme 2006 : Vortr{\"a}ge der 13. ITG/GMA-Fachtagung vom 13. bis 14.3.2006 in Freiburg/Breisgau},
  publisher = {VDE Verl.},
  address   = {Berlin},
  isbn      = {3-8007-2939-3},
  pages     = {165 -- 168},
  year      = {2006},
  language  = {de}
}
@inproceedings{FeldmannPyschnyDoeringetal.2012,
  author    = {Feldmann, Markus and Pyschny, D. and D{\"o}ring, Bernd and Kuhnhenne, Markus},
  title     = {Life cycle assessment of steel constructions},
  series = {Life-cycle and sustainability of civil infrastructure systems : proceedings of the Third International Symposium on Life-Cycle Civil Engineering (IALCCE'12) : Vienna, Austria, October 3-6, 2012},
  booktitle = {Life-cycle and sustainability of civil infrastructure systems : proceedings of the Third International Symposium on Life-Cycle Civil Engineering (IALCCE'12) : Vienna, Austria, October 3-6, 2012},
  publisher = {Taylor and Francis},
  address   = {Hoboken},
  organization    = {International Symposium on Life-Cycle Civil Engineering <3, 2012, Wien>},
  isbn      = {978-0-203-10336-4},
  pages     = {321},
  year      = {2012},
  language  = {en}
}
@inproceedings{KunfermannDrumm2005,
  author    = {Kunfermann, Philipp and Drumm, Christian},
  title     = {Lifting XML schemas to ontologies - the concept finder algorithm},
  series = {MEDIATE 2005 First International Workshop on Mediation in Semantic Web Services Proceedings of the First International Workshop on Mediation in Semantic Web Services (MEDIATE 2005)},
  booktitle = {MEDIATE 2005 First International Workshop on Mediation in Semantic Web Services Proceedings of the First International Workshop on Mediation in Semantic Web Services (MEDIATE 2005)},
  pages     = {113 -- 122},
  year      = {2005},
  language  = {en}
}
@inproceedings{WagnerYoshinobuSchoening2008,
  author    = {Wagner, Torsten and Yoshinobu, T. and Sch{\"o}ning, Michael Josef},
  title     = {Light-addressable potentiometric sensor as semiconductor-based sensor platform for (bio-) chemical sensing},
  series = {Armenian Journal of Physics},
  booktitle = {Armenian Journal of Physics},
  issn      = {1829-1171},
  pages     = {99 -- 103},
  year      = {2008},
  language  = {en}
}
@inproceedings{BreuerRaueMangetal.2015,
  author    = {Breuer, Lars and Raue, Markus and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Light-stimulated hydrogel actuators with incorporated graphene oxide for microfluidic applications},
  series = {12. Dresdner Sensor-Symposium 2015},
  booktitle = {12. Dresdner Sensor-Symposium 2015},
  doi       = {10.5162/12dss2015/P5.8},
  pages     = {206 -- 209},
  year      = {2015},
  language  = {en}
}
@inproceedings{BreuerGuthmannSchoeningetal.2017,
  author    = {Breuer, Lars and Guthmann, Eric and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Light-Stimulated Hydrogels with Incorporated Graphene Oxide as Actuator Material for Flow Control in Microfluidic Applications},
  series = {Proceedings Eurosensors 2017 Conference, Paris, France, 3-6 September 2017},
  booktitle = {Proceedings Eurosensors 2017 Conference, Paris, France, 3-6 September 2017},
  doi       = {10.3390/proceedings1040524},
  pages     = {1 -- 4},
  year      = {2017},
  language  = {en}
}
@inproceedings{KernKrichelMueller2001,
  author    = {Kern, Alexander and Krichel, Frank and M{\"u}ller, Klaus-Peter},
  title     = {Lightning protection design of a renewable energy hybrid-system without power mains connection},
  year      = {2001},
  abstract  = {In the year 2000 a direct lightning strike to the hybridsystem without power mains connection VATALI on the Greek island Crete results in the destruction and damage of some mechanical and electrical components. The hybrid-system VATALI was not lightning protected at that time. The hardware damage costs are approx. 60,000 €. The exposed site of the hybrid-system on top of a mountain was and still is the reason for a high risk of lightning strikes. Also in the future further lightning strikes have to be taken into consideration. In the paper a fundamental lightning protection design concept for renewable energy hybrid-systems without power mains connection and protection measures against direct strikes and overvoltages are shown in detail. The design concept was realized exemplarily for the hybrid-system VATALI. The hardware costs for the protection measures were about 15,000 €. About 50\% of the costs are due to protection measures against direct strikes, 50\% are due to overvoltage protection. Future extensions, new installations, or modifications have to be included into the lightning protection design concept of the hybrid-system.},
  language  = {en}
}
@inproceedings{PothMonzonTippkoetteretal.2010,
  author    = {Poth, Sebastian and Monzon, Magaly and Tippk{\"o}tter, Nils and Ulber, Roland},
  title     = {Lignocellulosic biorefinery : process integration of hydrolysis and fermentation},
  series = {Proceedings / 11th European Workshop on Lignocellulosics and Pulp : August 16 - 19, 2010, Hamburg, Germany},
  booktitle = {Proceedings / 11th European Workshop on Lignocellulosics and Pulp : August 16 - 19, 2010, Hamburg, Germany},
  publisher = {vTi},
  address   = {Hamburg},
  pages     = {65 -- 68},
  year      = {2010},
  language  = {en}
}
@inproceedings{StaatHeitzer1997,
  author    = {Staat, Manfred and Heitzer, Michael},
  title     = {Limit and shakedown analysis for plastic design},
  year      = {1997},
  abstract  = {Limit and shakedown theorems are exact theories of classical plasticity for the direct computation of safety factors or of the load carrying capacity under constant and varying loads. Simple versions of limit and shakedown analysis are the basis of all design codes for pressure vessels and pipings. Using Finite Element Methods more realistic modeling can be used for a more rational design. The methods can be extended to yield optimum plastic design. In this paper we present a first implementation in FE of limit and shakedown analyses for perfectly plastic material. Limit and shakedown analyses are done of a pipe-junction and a interaction diagram is calculated. The results are in good correspondence with the analytic solution we give in the appendix.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@inproceedings{TranTrinhDaoetal.2022,
  author    = {Tran, Ngoc Trinh and Trinh, Tu Luc and Dao, Ngoc Tien and Giap, Van Tan and Truong, Manh Khuyen and Dinh, Thuy Ha and Staat, Manfred},
  title     = {Limit and shakedown analysis of structures under random strength},
  series = {Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training, Hanoi, December 2-3, 2022},
  booktitle = {Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training, Hanoi, December 2-3, 2022},
  publisher = {Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik)},
  address   = {Hanoi},
  isbn      = {978-604-357-084-7},
  pages     = {510 -- 518},
  year      = {2022},
  abstract  = {Direct methods comprising limit and shakedown analysis is a branch of computational mechanics. It plays a significant role in mechanical and civil engineering design. The concept of direct method aims to determinate the ultimate load bearing capacity of structures beyond the elastic range. For practical problems, the direct methods lead to nonlinear convex optimization problems with a large number of variables and onstraints. If strength and loading are random quantities, the problem of shakedown analysis is considered as stochastic programming. This paper presents a method so called chance constrained programming, an effective method of stochastic programming, to solve shakedown analysis problem under random condition of strength. In this our investigation, the loading is deterministic, the strength is distributed as normal or lognormal variables.},
  language  = {en}
}
@inproceedings{Staat2012,
  author    = {Staat, Manfred},
  title     = {Limit and shakedown analysis under uncertainty},
  series = {Proceedings International Conference on Advances in Computational Mechanics (ACOME)},
  booktitle = {Proceedings International Conference on Advances in Computational Mechanics (ACOME)},
  pages     = {837 -- 861},
  year      = {2012},
  language  = {de}
}
@inproceedings{StaatTranPham2008,
  author    = {Staat, Manfred and Tran, Thanh Ngoc and Pham, Phu Tinh},
  title     = {Limit and shakedown reliability analysis by nonlinear programming},
  year      = {2008},
  abstract  = {7th International Conference on Reliability of Materials and Structures (RELMAS 2008). June 17 - 20, 2008 ; Saint Petersburg, Russia. pp 354-358. Reprint with corrections in red Introduction Analysis of advanced structures working under extreme heavy loading such as nuclear power plants and piping system should take into account the randomness of loading, geometrical and material parameters. The existing reliability are restricted mostly to the elastic working regime, e.g. allowable local stresses. Development of the limit and shakedown reliability-based analysis and design methods, exploiting potential of the shakedown working regime, is highly needed. In this paper the application of a new algorithm of probabilistic limit and shakedown analysis for shell structures is presented, in which the loading and strength of the material as well as the thickness of the shell are considered as random variables. The reliability analysis problems may be efficiently solved by using a system combining the available FE codes, a deterministic limit and shakedown analysis, and the First and Second Order Reliability Methods (FORM/SORM). Non-linear sensitivity analyses are obtained directly from the solution of the deterministic problem without extra computational costs.},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}
@inproceedings{StaatHeitzerHicken1999,
  author    = {Staat, Manfred and Heitzer, Michael and Hicken, E. F.},
  title     = {LISA - ein europ{\"a}isches Projekt zur FEM-basierten Traglast- und Einspielanalyse},
  year      = {1999},
  abstract  = {Traglast- und Einspielanalysen sind vereinfachte doch exakte Verfahren der Plastizit{\"a}t, die neben ausreichender Verformbarkeit keine einschr{\"a}nkenden Voraussetzungen beinhalten. Die Vereinfachungen betreffen die Beschaffung der Daten und Modelle f{\"u}r Details der Lastgeschichte und des Stoffverhaltens. Anders als die klassische Behandlung nichtlinearer Probleme der Strukturmechanik f{\"u}hrt die Methode auf Optimierungsprobleme. Diese sind bei realistischen FEM-Modellen sehr groß. Das hat die industrielle Anwendung der Traglast- und Einspielanalysen stark verz{\"o}gert. Diese Situation wird durch das Brite-EuRam Projekt LISA grundlegend ge{\"a}ndert. In LISA entsteht auf der Basis des industriellen FEM-Programms PERMAS ein Verfahren zur direkten Berechnung der Tragf{\"a}higkeit duktiler Strukturen. Damit kann der Betriebsbereich von Komponenten und Bauwerken auf den plastischen Bereich erweitert werden, ohne den Aufwand gegen{\"u}ber elastischen Analysen wesentlich zu erh{\"o}hen. Die beachtlichen Rechenzeitgewinne erlauben Parameterstudien und die Berechnung von Interaktionsdiagrammen, die einen schnellen {\"U}berblick {\"u}ber m{\"o}gliche Betriebsbereiche vermitteln. Es zeigt sich, daß abh{\"a}ngig von der Komponente und ihren Belastungen teilweise entscheidende Sicherheitsgewinne zur Erweiterung der Betriebsbereiche erzielt werden k{\"o}nnen. Das Vorgehen erfordert vom Anwender oft ein gewisses Umdenken. Es werden keine Spannungen berechnet, um damit Sicherheit und Lebensdauer zu interpretieren. Statt dessen berechnet man direkt die gesuchte Sicherheit. Der Post-Prozessor wird nur noch zur Modell- und Rechenkontrolle ben{\"o}tigt. Das Vorgehen ist {\"a}hnlich der Stabilit{\"a}tsanalyse (Knicken, Beulen). Durch namhafte industrielle Projektpartner werden Validierung und die Anwendbarkeit auf eine breite Palette technischer Probleme garantiert. Die ebenfalls in LISA entwickelten Zuverl{\"a}ssigkeitsanalysen sind nichlinear erst auf der Basis direkter Verfahren effektiv m{\"o}glich. Ohne Traglast- und Einspielanalyse ist plastische Strukturoptimierung auch heute kaum durchf{\"u}hrbar. Auf die vorgesehenen Erweiterungen der Werkstoffmodellierung f{\"u}r nichtlineare Verfestigung und f{\"u}r Sch{\"a}digung konnte hier nicht eingegangen werden. Es herrscht ein deutlicher Mangel an Experimenten zum Nachweis der Grenzen zwischen elastischem Einspielen und dem Versagen durch LCF oder durch Ratchetting.},
  subject      = {Einspielen <Werkstoff>},
  language  = {de}
}
@inproceedings{StaatHeitzerHicken1998,
  author    = {Staat, Manfred and Heitzer, M. and Hicken, E. F.},
  title     = {LISA, ein europ{\"a}isches Projekt zur direkten Berechnung der Tragf{\"a}higkeit duktiler Strukturen},
  year      = {1998},
  abstract  = {Traglast- und Einspielanalysen sind vereinfachte doch exakte Verfahren der Plastizit{\"a}t, die neben ausreichender Verformbarkeit keine einschr{\"a}nkenden Voraussetzungen beinhalten. Die Vereinfachungen betreffen die Beschaffung der Daten und Modelle f{\"u}r Details der Lastgeschichte und des Stoffverhaltens. Anders als die klassische Behandlung nichtlinearer Probleme der Strukturmechanik f{\"u}hrt die Methode auf Optimierungsprobleme. Diese sind bei realistischen FEM-Modellen sehr groß. Das hat die industrielle Anwendung der Traglast- und Einspielanalysen stark verz{\"o}gert. Diese Situation wird durch das Brite-EuRam Projekt LISA grundlegend ge{\"a}ndert. Die Autoren m{\"o}chten der Europ{\"a}ischen Kommission an dieser Stelle f{\"u}r die F{\"o}rderung ausdr{\"u}cklich danken. In LISA entsteht auf der Basis des industriellen FEM-Programms PERMAS ein Verfahren zur direkten Berechnung der Tragf{\"a}higkeit duktiler Strukturen. Damit kann der Betriebsbereich von Komponenten und Bauwerken auf den plastischen Bereich erweitert werden, ohne den Aufwand gegen{\"u}ber elastischen Analysen wesentlich zu erh{\"o}hen. Die beachtlichen Rechenzeitgewinne erlauben Parameterstudien und die Berechnung von Interaktionsdiagrammen, die einen schnellen {\"U}berblick {\"u}ber m{\"o}gliche Betriebsbereiche vermitteln. Es zeigt sich, daß abh{\"a}ngig von der Komponente und ihren Belastungen teilweise entscheidende Sicherheitsgewinne zur Erweiterung der Betriebsbereiche erzielt werden k{\"o}nnen. Das Vorgehen erfordert vom Anwender oft ein gewisses Umdenken. Es werden keine Spannungen berechnet, um damit Sicherheit und Lebensdauer zu interpretieren. Statt dessen berechnet man direkt die gesuchte Sicherheit. Der Post-Prozessor wird nur noch zur Modell- und Rechenkontrolle ben{\"o}tigt. Das Vorgehen ist {\"a}nhlich der Stabilit{\"a}tsanalyse (Knicken, Beulen). Durch namhafte industrielle Projektpartner werden Validierung und die Anwendbarkeit auf eine breite Palette technischer Probleme garantiert. Die ebenfalls in LISA geplante Zuverl{\"a}ssigkeitsanalyse ist erst auf der Basis direkter Verfahren effektiv m{\"o}glich. Ohne Traglast- und Einspielanalyse ist plastische Strukturoptimierung auch heute kaum durchf{\"u}hrbar.},
  subject      = {Finite-Elemente-Methode},
  language  = {de}
}
@inproceedings{BohrnStuetzFleischeretal.2012,
  author    = {Bohrn, Ulrich and St{\"u}tz, Evamaria and Fleischer, Maximilian and Sch{\"o}ning, Michael Josef and Wagner, Patrick},
  title     = {Living cell-based gas sensor system for the detection of acetone in air},
  isbn      = {978-3-9813484-2-2},
  doi       = {10.5162/IMCS2012/3.2.3},
  pages     = {269 -- 272},
  year      = {2012},
  language  = {en}
}
@inproceedings{UibelBlass2006,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {Load Carrying Capacity of Joints with Dowel Type Fasteners in Solid Wood Panels},
  series = {Proceedings. CIB-W18 Meeting 2006, Florence, Italy 2006},
  booktitle = {Proceedings. CIB-W18 Meeting 2006, Florence, Italy 2006},
  issn      = {0945-6996},
  pages     = {1 -- 10},
  year      = {2006},
  language  = {en}
}
@inproceedings{DiltheySchleserHeggeretal.2007,
  author    = {Dilthey, Ulrich and Schleser, Markus and Hegger, Josef and Voss, Stefan},
  title     = {Load-bearing behaviour of polymer-impregnated textiles in concrete},
  series = {Fifth International Workshop on High Performance Fiber Reinforced Cement Composites (HPFRCC 5) : Mainz, July 10 - 13, 2007. (RILEM proceedings. 53)},
  booktitle = {Fifth International Workshop on High Performance Fiber Reinforced Cement Composites (HPFRCC 5) : Mainz, July 10 - 13, 2007. (RILEM proceedings. 53)},
  editor    = {Reinhardt, Hans W.},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Workshop on High Performance Fiber Reinforced Cement Composites <5, 2007, Mainz>},
  isbn      = {978-2-35158-046-2},
  pages     = {183 -- 192},
  year      = {2007},
  language  = {en}
}
@inproceedings{SchuermannWollert2008,
  author    = {Sch{\"u}rmann, Volker and Wollert, J{\"o}rg},
  title     = {Location based Services in der Geb{\"a}udeautomation},
  series = {Wireless Technologies Kongress 2008: von der Technologie zur Anwendung ; [10. Kongress, 23. - 24. September 2008, Bochum]},
  booktitle = {Wireless Technologies Kongress 2008: von der Technologie zur Anwendung ; [10. Kongress, 23. - 24. September 2008, Bochum]},
  publisher = {Aka},
  address   = {Heidelberg},
  organization    = {Wireless-Technologies-Kongress <10, 2008, Bochum>},
  isbn      = {978-3-89838-608-1},
  pages     = {313 -- 322},
  year      = {2008},
  language  = {de}
}
@inproceedings{BoehmHellmannsBackesetal.2006,
  author    = {B{\"o}hm, Stefan and Hellmanns, Mark and Backes, Andreas and Dilger, Klaus},
  title     = {Lock-in thermography based NDT of automotive parts},
  series = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  booktitle = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  publisher = {Beijing Adhesion Society of China},
  address   = {Beijing},
  pages     = {382 -- 384},
  year      = {2006},
  language  = {en}
}
@inproceedings{AnthrakidisRusackSchwarzer2010,
  author    = {Anthrakidis, Anette and Rusack, Markus and Schwarzer, Klemens},
  title     = {Low effort measurement method of PTC-efficiency},
  series = {SolarPACES 2010 : the CSP conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {48 -- 49},
  year      = {2010},
  language  = {en}
}
@inproceedings{FunkeBoernerKeinzetal.2012,
  author    = {Funke, Harald and B{\"o}rner, Sebastian and Keinz, Jan and Hendrick, P. and Recker, E.},
  title     = {Low NOx Hydrogen combustion chamber for industrial gas turbine applications", 14th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery},
  series = {ISROMAC-14 : the Forteenth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery ; Honolulu, Hawaii, February 27 - March 02nd, 2012},
  booktitle = {ISROMAC-14 : the Forteenth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery ; Honolulu, Hawaii, February 27 - March 02nd, 2012},
  year      = {2012},
  language  = {en}
}
@inproceedings{Dachwald2007,
  author    = {Dachwald, Bernd},
  title     = {Low-Thrust Mission Analysis and Global Trajectory Optimization Using Evolutionary Neurocontrol: New Results},
  series = {European Workshop on Space Mission Analysis ESA/ESOC, Darmstadt, Germany 10 { 12 Dec 2007},
  booktitle = {European Workshop on Space Mission Analysis ESA/ESOC, Darmstadt, Germany 10 { 12 Dec 2007},
  year      = {2007},
  abstract  = {Interplanetary trajectories for low-thrust spacecraft are often characterized by multiple revolutions around the sun. Unfortunately, the convergence of traditional trajectory optimizers that are based on numerical optimal control methods depends strongly on an adequate initial guess for the control function (if a direct method is used) or for the starting values of the adjoint vector (if an indirect method is used). Especially when many revolutions around the sun are re- quired, trajectory optimization becomes a very difficult and time-consuming task that involves a lot of experience and expert knowledge in astrodynamics and optimal control theory, because an adequate initial guess is extremely hard to find. Evolutionary neurocontrol (ENC) was proposed as a smart method for low-thrust trajectory optimization that fuses artificial neural networks and evolutionary algorithms to so-called evolutionary neurocontrollers (ENCs) [1]. Inspired by natural archetypes, ENC attacks the trajectoryoptimization problem from the perspective of artificial intelligence and machine learning, a perspective that is quite different from that of optimal control theory. Within the context of ENC, a trajectory is regarded as the result of a spacecraft steering strategy that maps permanently the actual spacecraft state and the actual target state onto the actual spacecraft control vector. This way, the problem of searching the optimal spacecraft trajectory is equivalent to the problem of searching (or "learning") the optimal spacecraft steering strategy. An artificial neural network is used to implement such a spacecraft steering strategy. It can be regarded as a parameterized function (the network function) that is defined by the internal network parameters. Therefore, each distinct set of network parameters defines a different network function and thus a different steering strategy. The problem of searching the optimal steering strategy is now equivalent to the problem of searching the optimal set of network parameters. Evolutionary algorithms that work on a population of (artificial) chromosomes are used to find the optimal network parameters, because the parameters can be easily mapped onto a chromosome. The trajectory optimization problem is solved when the optimal chromosome is found. A comparison of solar sail trajectories that have been published by others [2, 3, 4, 5] with ENC-trajectories has shown that ENCs can be successfully applied for near-globally optimal spacecraft control [1, 6] and that they are able to find trajectories that are closer to the (unknown) global optimum, because they explore the trajectory search space more exhaustively than a human expert can do. The obtained trajectories are fairly accurate with respect to the terminal constraint. If a more accurate trajectory is required, the ENC-solution can be used as an initial guess for a local trajectory optimization method. Using ENC, low-thrust trajectories can be optimized without an initial guess and without expert attendance. Here, new results for nuclear electric spacecraft and for solar sail spacecraft are presented and it will be shown that ENCs find very good trajectories even for very difficult problems. Trajectory optimization results are presented for 1. NASA's Solar Polar Imager Mission, a mission to attain a highly inclined close solar orbit with a solar sail [7] 2. a mission to de ect asteroid Apophis with a solar sail from a retrograde orbit with a very-high velocity impact [8, 9] 3. JPL's \2nd Global Trajectory Optimization Competition", a grand tour to visit four asteroids from different classes with a NEP spacecraft},
  language  = {en}
}
@inproceedings{KuhnhenneFeldmannDoeringetal.2007,
  author    = {Kuhnhenne, Markus and Feldmann, Markus and D{\"o}ring, Bernd and Spranger, Sascha},
  title     = {Luftdichtheit im Stahlleichtbau - Geb{\"a}udeh{\"u}llen in Sandwichbauweise},
  series = {Dichte Geb{\"a}udeh{\"u}lle, Thermografie und Wohnungsl{\"u}ftung : 2. Europ{\"a}isches BlowerDoor-Symposium : 16.3. - 17.3. 2007, Kassel},
  booktitle = {Dichte Geb{\"a}udeh{\"u}lle, Thermografie und Wohnungsl{\"u}ftung : 2. Europ{\"a}isches BlowerDoor-Symposium : 16.3. - 17.3. 2007, Kassel},
  publisher = {Energie + Umwelt-Zentrum},
  organization    = {Europ{\"a}isches BlowerDoor-Symposium <2, 2007, Kassel>},
  pages     = {121 -- 134},
  year      = {2007},
  language  = {de}
}
@inproceedings{HuberRauStreblowetal.2014,
  author    = {Huber, Max and Rau, Sebastian and Streblow, Rita and Wollert, J{\"o}rg and M{\"u}ller, Dirk},
  title     = {L{\"u}ftungskan{\"a}le als Funkstrecke},
  series = {Jahreskolloquium Kommunikation in der Automation (KommA 2014) : Lemgo, 18.11.2014 / J{\"u}rgen Jasperneite ... (Hrsg.)},
  booktitle = {Jahreskolloquium Kommunikation in der Automation (KommA 2014) : Lemgo, 18.11.2014 / J{\"u}rgen Jasperneite ... (Hrsg.)},
  organization    = {Jahreskolloquium Kommunikation in der Automation <5, 2014, Lemgo>},
  isbn      = {978-3-9814062-4-5},
  pages     = {1 -- 8},
  year      = {2014},
  language  = {de}
}
@inproceedings{NikolovskiRekeElsenetal.2021,
  author    = {Nikolovski, Gjorgji and Reke, Michael and Elsen, Ingo and Schiffer, Stefan},
  title     = {Machine learning based 3D object detection for navigation in unstructured environments},
  series = {2021 IEEE Intelligent Vehicles Symposium Workshops (IV Workshops)},
  booktitle = {2021 IEEE Intelligent Vehicles Symposium Workshops (IV Workshops)},
  publisher = {IEEE},
  isbn      = {978-1-6654-7921-9},
  doi       = {10.1109/IVWorkshops54471.2021.9669218},
  pages     = {236 -- 242},
  year      = {2021},
  abstract  = {In this paper we investigate the use of deep neural networks for 3D object detection in uncommon, unstructured environments such as in an open-pit mine. While neural nets are frequently used for object detection in regular autonomous driving applications, more unusual driving scenarios aside street traffic pose additional challenges. For one, the collection of appropriate data sets to train the networks is an issue. For another, testing the performance of trained networks often requires tailored integration with the particular domain as well. While there exist different solutions for these problems in regular autonomous driving, there are only very few approaches that work for special domains just as well. We address both the challenges above in this work. First, we discuss two possible ways of acquiring data for training and evaluation. That is, we evaluate a semi-automated annotation of recorded LIDAR data and we examine synthetic data generation. Using these datasets we train and test different deep neural network for the task of object detection. Second, we propose a possible integration of a ROS2 detector module for an autonomous driving platform. Finally, we present the performance of three state-of-the-art deep neural networks in the domain of 3D object detection on a synthetic dataset and a smaller one containing a characteristic object from an open-pit mine.},
  language  = {en}
}
@inproceedings{GiresiniButenwegAndreinietal.2014,
  author    = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.},
  title     = {Macro-elements identification in historic chapels: the case of St. Venerio Chapel in Reggiolo - Emilia Romagna},
  series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  organization    = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{SimsekKrauseEngelmann2024,
  author    = {Simsek, Beril and Krause, Hans-Joachim and Engelmann, Ulrich M.},
  title     = {Magnetic biosensing with magnetic nanoparticles: Simulative approach to predict signal intensity in frequency mixing magnetic detection},
  series = {4th YRA MedTech Symposium 2024 : February 1 / 2024 / FH Aachen},
  booktitle = {4th YRA MedTech Symposium 2024 : February 1 / 2024 / FH Aachen},
  editor    = {Digel, Ilya and Staat, Manfred and Trzewik, J{\"u}rgen and Sielemann, Stefanie and Erni, Daniel and Zylka, Waldemar},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-65-3},
  doi       = {10.17185/duepublico/81475},
  pages     = {27 -- 28},
  year      = {2024},
  abstract  = {Magnetic nanoparticles (MNP) are investigated with great interest for biomedical applications in diagnostics (e.g. imaging: magnetic particle imaging (MPI)), therapeutics (e.g. hyperthermia: magnetic fluid hyperthermia (MFH)) and multi-purpose biosensing (e.g. magnetic immunoassays (MIA)). What all of these applications have in common is that they are based on the unique magnetic relaxation mechanisms of MNP in an alternating magnetic field (AMF). While MFH and MPI are currently the most prominent examples of biomedical applications, here we present results on the relatively new biosensing application of frequency mixing magnetic detection (FMMD) from a simulation perspective. In general, we ask how the key parameters of MNP (core size and magnetic anisotropy) affect the FMMD signal: by varying the core size, we investigate the effect of the magnetic volume per MNP; and by changing the effective magnetic anisotropy, we study the MNPs' flexibility to leave its preferred magnetization direction. From this, we predict the most effective combination of MNP core size and magnetic anisotropy for maximum signal generation.},
  language  = {en}
}
@inproceedings{KernHeidlerSeeversetal.2004,
  author    = {Kern, Alexander and Heidler, Fridolin and Seevers, M. and Zischank, Wolfgang J.},
  title     = {Magnetic Fields and Induced Voltages in case of a Direct Strike - Comparison of Results obtained from Measurements at a Scaled Building to those of IEC 62305-4},
  isbn      = {0304-3886},
  year      = {2004},
  abstract  = {In the paper the results obtained from experiments at a modelled reinforced building in case of a direct lightning strike are compared with calculations. The comparison includes peak values of the magnetic field Hmax, its derivative (dH/dt)max and of induced voltages umax in typical cable routings. The experiments are performed at a 1:6 scaled building and the results are extrapolated using the similarity relations theory. The calculations are based on the approximate formulae given in IEC 62305-4 and have to be supplemented by a rough estimation of the additional shielding effect of a second reinforcement layer. The comparison shows, that the measured peak values of the magnetic field and its derivative are mostly lower than the calculated. The induced voltages are in good agreement. Hence, calculations of the induced voltages based on IEC 62305-4 are a good method for lightning protection studies of buildings, where the reinforcement is used as a grid-like electromagnetic shield.},
  subject      = {Blitz},
  language  = {en}
}
@inproceedings{ZischankHeidlerWiesingeretal.2004,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Wiesinger, J. and Stimper, K. and Kern, Alexander and Seevers, M.},
  title     = {Magnetic Fields and Induced Voltages inside LPZ 1 Measured at a 1:6 Scale Model Building},
  year      = {2004},
  abstract  = {Laborexperimente zu Blitzschutzzonen in Stahlbetongeb{\"a}uden anhand eines Modells im Maßstab 1:6},
  language  = {en}
}
@inproceedings{KatzWillner2006,
  author    = {Katz, Eugenii and Willner, Itamar},
  title     = {Magneto-controlled quantized electron transfer to surface-confined redox units and metal nanoparticles},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1528},
  year      = {2006},
  abstract  = {Hydrophobic magnetic nanoparticles (NPs) consisting of undecanoate-capped magnetite (Fe3O4, average diameter ca. 5 nm) are used to control quantized electron transfer to surface-confined redox units and metal NPs. A two-phase system consisting of an aqueous electrolyte solution and a toluene phase that includes the suspended undecanoatecapped magnetic NPs is used to control the interfacial properties of the electrode surface. The attracted magnetic NPs form a hydrophobic layer on the electrode surface resulting in the change of the mechanisms of the surface-confined electrochemical processes. A quinone-monolayer modified Au electrode demonstrates an aqueous-type of the electrochemical process (2e-+2H+ redox mechanism) for the quinone units in the absence of the hydrophobic magnetic NPs, while the attraction of the magnetic NPs to the surface results in the stepwise single-electron transfer mechanism characteristic of a dry nonaqueous medium. Also, the attraction of the hydrophobic magnetic NPs to the Au electrode surface modified with Au NPs (ca. 1.4 nm) yields a microenvironment with a low dielectric constant that results in the single-electron quantum charging of the Au NPs.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{AjonaHerrmannSperdutoetal.1996,
  author    = {Ajona, J. I. and Herrmann, Ulf and Sperduto, F. and Farinha-Mendes, J.},
  title     = {Main Achievements within ARDISS (Advanced Receiver for Direct Solar Steam Production in Parabolic Trough Solar Power Plants) Project},
  series = {Components, tools, facilities and measurement techniques. - (Solar thermal concentrating technologies : proceedings of the 8th international symposium, October, 6 - 11, 1996, K{\"o}ln, Germany ; Vol. 2)},
  booktitle = {Components, tools, facilities and measurement techniques. - (Solar thermal concentrating technologies : proceedings of the 8th international symposium, October, 6 - 11, 1996, K{\"o}ln, Germany ; Vol. 2)},
  editor    = {Becker, Manfred},
  publisher = {M{\"u}ller},
  address   = {Heidelberg},
  isbn      = {3-7880-7616-X},
  pages     = {733 -- 754},
  year      = {1996},
  language  = {en}
}
@inproceedings{CzarneckiWinkelmannSpiliopoulou2011,
  author    = {Czarnecki, Christian and Winkelmann, Axel and Spiliopoulou, Myra},
  title     = {Making business systems in the telecommunication industry more customer-oriented},
  series = {Information Systems Development : Business Systems and Services: Modeling and Development},
  booktitle = {Information Systems Development : Business Systems and Services: Modeling and Development},
  editor    = {Pokorny, Jaroslav and Repa, Vaclav and Richta, Karel and Wojtkowski, Wita and Linger, Henry and Barry, Chris and Lang, Michael},
  publisher = {Springer},
  address   = {New York},
  isbn      = {978-1-4419-9645-9 (Print)},
  doi       = {10.1007/978-1-4419-9790-6_14},
  pages     = {169 -- 180},
  year      = {2011},
  abstract  = {Market changes have forced telecommunication companies to transform their business. Increased competition, short innovation cycles, changed usage patterns, increased customer expectations and cost reduction are the main drivers. Our objective is to analyze to what extend transformation projects have improved the orientation towards the end-customers. Therefore, we selected 38 real-life case studies that are dealing with customer orientation. Our analysis is based on a telecommunication-specific framework that aligns strategy, business processes and information systems. The result of our analysis shows the following: transformation projects that aim to improve the customer orientation are combined with clear goals on costs and revenue of the enterprise. These projects are usually directly linked to the customer touch points, but also to the development and provisioning of products. Furthermore, the analysis shows that customer orientation is not the sole trigger for transformation. There is no one-fits-all solution; rather, improved customer orientation needs aligned changes of business processes as well as information systems related to different parts of the company.},
  language  = {en}
}
@inproceedings{SchuetzBreuerHoefkenetal.2013,
  author    = {Sch{\"u}tz, P. and Breuer, M. and H{\"o}fken, Hans-Wilhelm and Schuba, Marko},
  title     = {Malware proof on mobile phone exhibits based on GSM/GPRS traces},
  series = {The Second International Conference on Cyber Security, Cyber Peacefare and Digital Forensic (CyberSec 2013) : 04.03. - 06.03.2013, Kuala Lumpur, Malaysia},
  booktitle = {The Second International Conference on Cyber Security, Cyber Peacefare and Digital Forensic (CyberSec 2013) : 04.03. - 06.03.2013, Kuala Lumpur, Malaysia},
  publisher = {The Society of Digital Information and Wireless Communication},
  isbn      = {978-0-9853483-7-3},
  pages     = {89 -- 96},
  year      = {2013},
  language  = {en}
}
@inproceedings{Goldbach2010,
  author    = {Goldbach, Daniel},
  title     = {Management der funktionalen Sicherheit einer Entwicklung eines sicherheitskritischen Systems im Bereich Nutzfahrzeuge},
  series = {Commercial vehicle technology 2010 : proceedings of the 1st Commercial Vehicle Technology Symposium (CVT 2010), March 16 - 18, 2010, Kaiserslautern / K. Berns ... (ed.)},
  booktitle = {Commercial vehicle technology 2010 : proceedings of the 1st Commercial Vehicle Technology Symposium (CVT 2010), March 16 - 18, 2010, Kaiserslautern / K. Berns ... (ed.)},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8322-9040-5},
  pages     = {487 -- 495},
  year      = {2010},
  language  = {de}
}
@inproceedings{BungOertel2014,
  author    = {Bung, Daniel B. and Oertel, Mario},
  title     = {Manipulation of non-aerated cavity flow on a stepped spillway model},
  series = {3rd European IAHR Congress : April 14 - 16, 2014, Porto},
  booktitle = {3rd European IAHR Congress : April 14 - 16, 2014, Porto},
  publisher = {Univ. of Porto},
  address   = {Porto},
  organization    = {International Association of Hydro-Environment Engineering and Research},
  year      = {2014},
  language  = {en}
}
@inproceedings{HailerWeberArent2019,
  author    = {Hailer, Benjamin and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for Autoclave-Produced Sandwich Structures},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 8},
  year      = {2019},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2019,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 10},
  year      = {2019},
  language  = {en}
}