@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Statistical modeling of laser welding of DP/TRIP steel sheets},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.05.025},
  pages     = {92 -- 101},
  year      = {2012},
  abstract  = {In this research work, a statistical analysis of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box-Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Optimization of laser welding of DP/TRIP steel sheets using statistical approach},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.06.028},
  pages     = {255 -- 262},
  year      = {2012},
  abstract  = {Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box-Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions.},
  language  = {en}
}
@article{ReisgenOlschokJakobsetal.2012,
  author    = {Reisgen, Uwe and Olschok, Simon and Jakobs, Stefan and Schleser, Markus and Mokrov, Oleg and Rossiter, Eduardo},
  title     = {Laser beam submerged arc hybrid welding},
  series = {Physics procedia},
  volume    = {39},
  journal   = {Physics procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892},
  doi       = {10.1016/j.phpro.2012.10.016},
  pages     = {75 -- 83},
  year      = {2012},
  abstract  = {The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.},
  language  = {en}
}
@article{WincklerKruegerSchnitzleretal.2014,
  author    = {Winckler, Silvia and Krueger, Rolf and Schnitzler, Thomas and Zang, Werner and Fischer, Rainer and Biselli, Manfred},
  title     = {A sensitive monitoring system for mammalian cell cultivation processes: a PAT approach},
  series = {Bioprocess and biosystems engineering},
  volume    = {37},
  journal   = {Bioprocess and biosystems engineering},
  number    = {5},
  publisher = {Springer},
  address   = {Berlin, Heidelberg},
  issn      = {1615-7591 (Print) 1615-7605 (Online)},
  doi       = {10.1007/s00449-013-1062-8},
  pages     = {901 -- 912},
  year      = {2014},
  abstract  = {Biopharmaceuticals such as antibodies are produced in cultivated mammalian cells, which must be monitored to comply with good manufacturing practice. We, therefore, developed a fully automated system comprising a specific exhaust gas analyzer, inline analytics and a corresponding algorithm to precisely determine the oxygen uptake rate, carbon dioxide evolution rate, carbon dioxide transfer rate, transfer quotient and respiratory quotient without interrupting the ongoing cultivation, in order to assess its reproducibility. The system was verified using chemical simulation experiments and was able to measure the respiratory activity of hybridoma cells and DG44 cells (derived from Chinese hamster ovary cells) with satisfactory results at a minimum viable cell density of ~2.0 × 10⁵ cells ml⁻¹. The system was suitable for both batch and fed-batch cultivations in bubble-aerated and membrane-aerated reactors, with and without the control of pH and dissolved oxygen.},
  language  = {en}
}
@book{DavidBenkner2013,
  author    = {David, Klaus and Benkner, Thorsten},
  title     = {Digitale Mobilfunksysteme},
  number    = {Repr. 1996},
  publisher = {Vieweg \& Teubner},
  address   = {Wiesbaden},
  isbn      = {978-3-322-92768-2},
  pages     = {XIII, 458 S.},
  year      = {2013},
  language  = {de}
}
@article{Schnitzler2009,
  author    = {Schnitzler, Thomas},
  title     = {Cultivation of hybridoma cell line CF-10H5 (DSMZ ACC477)},
  series = {Application notes / Sartorius stedim biotech},
  journal   = {Application notes / Sartorius stedim biotech},
  pages     = {1 -- 4},
  year      = {2009},
  language  = {en}
}
@article{Schnitzler2009,
  author    = {Schnitzler, Thomas},
  title     = {Kultivierung der Hybridomazelllinie CF-10H5 (DSMZ ACC477)},
  series = {Application notes / Sartorius stedim biotech},
  journal   = {Application notes / Sartorius stedim biotech},
  publisher = {Sartorius Stedim Biotec},
  address   = {Aubagne},
  year      = {2009},
  language  = {de}
}
@article{SchnitzlerBiselli2005,
  author    = {Schnitzler, Thomas and Biselli, Manfred},
  title     = {Cultivo de lineas celulares de hibridoma por CF-10H5 (DSMZ ACC477) en el BIOSTAT B plus},
  series = {Noticias tecnicas del laboratorio},
  volume    = {13},
  journal   = {Noticias tecnicas del laboratorio},
  number    = {3},
  pages     = {7 -- 8},
  year      = {2005},
  language  = {es}
}
@inproceedings{StoebeHoefkenSchubaetal.2013,
  author    = {St{\"o}be, Rolf and H{\"o}fken, Hans-Wilhelm and Schuba, Marko and Breuer, Michael},
  title     = {Artificial ageing of mobile devices using a simulated GSM/GPRS network},
  series = {Eighth International Conference on Availability, Reliability and Security (ARES) : 2-6 Sept. 2013, Regensburg},
  booktitle = {Eighth International Conference on Availability, Reliability and Security (ARES) : 2-6 Sept. 2013, Regensburg},
  publisher = {IEEE},
  pages     = {493 -- 497},
  year      = {2013},
  language  = {en}
}
@inproceedings{HartungDilgerHellmannsetal.2009,
  author    = {Hartung, I. and Dilger, Klaus and Hellmanns, Mark and B{\"o}hme, Stefan},
  title     = {Repair of non-weldable steel structures to extend the life cycle},
  series = {Proceedings of the IIW International Conference on Advances in Welding and Allied Technologies : July 16 - 17, 2009, Singapore. (Welding in the world ; 53.2009, special issue)},
  booktitle = {Proceedings of the IIW International Conference on Advances in Welding and Allied Technologies : July 16 - 17, 2009, Singapore. (Welding in the world ; 53.2009, special issue)},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  organization    = {International Institute of Welding},
  isbn      = {978-981-08-3259-9},
  pages     = {569 -- 574},
  year      = {2009},
  language  = {en}
}
@inproceedings{HellmannsBoehmDilger2008,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Weight and noise reduction in power transmissions through epoxy resin foams},
  series = {Proceedings of the 31st annual meeting of the Adhesion Society : 17. - 20.2.2008, Austin, Texas},
  booktitle = {Proceedings of the 31st annual meeting of the Adhesion Society : 17. - 20.2.2008, Austin, Texas},
  publisher = {Adhesion Society},
  address   = {Blacksburg},
  organization    = {Adhesion Society},
  pages     = {291 -- 293},
  year      = {2008},
  language  = {en}
}
@techreport{HellmannsHesse2007,
  author    = {Hellmanns, Mark and Hesse, Joachim},
  title     = {Ger{\"a}uschminderung und Leichtbau in Leistungsgetrieben durch den Einsatz von Werkstoffverbunden : Abschlussbericht zu Nr. 3.1 : Berichtszeitraum: 1.3.2005 - 31.8.2007},
  publisher = {Bundesministerium f{\"u}r Wirtschaft und Arbeit (BMWi)},
  address   = {Berlin},
  pages     = {66 S.},
  year      = {2007},
  language  = {de}
}
@inproceedings{HellmannsBoehmDilger2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Implementation of a velocity controlled manual applicator for adhesives and sealants in the automotive industry in consideration of quality control},
  series = {Proceedings of the 29th annual meeting of the Adhesion Society : 19. - 22.2.2006, Jacksonville, Florida},
  booktitle = {Proceedings of the 29th annual meeting of the Adhesion Society : 19. - 22.2.2006, Jacksonville, Florida},
  publisher = {Adhesion Society},
  address   = {Blacksburg, Va.},
  organization    = {Adhesion Society},
  issn      = {1086-9506},
  pages     = {68 -- 70},
  year      = {2006},
  language  = {en}
}
@article{HellmannsBoehmDilger2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Manual applications of adhesives},
  series = {Journal of adhesion and interface},
  volume    = {Vol. 7},
  journal   = {Journal of adhesion and interface},
  number    = {No. 4},
  pages     = {24 -- 27},
  year      = {2006},
  language  = {en}
}
@inproceedings{ReisgenSchleserThiele2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Thiele, Regina},
  title     = {Schweißverbindungen in Lithium-Ionen-Batterien},
  series = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  booktitle = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {Große Schweißtechnische Tagung <2012, Saarbr{\"u}cken> ; Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren},
  isbn      = {978-3-87155-593-0},
  pages     = {157 -- 161},
  year      = {2012},
  language  = {de}
}
@inproceedings{ReisgenSchleserEssersetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Essers, Marc and Thiele, Regina and Schiebahn, Alexander},
  title     = {Klebstofffixiertes R{\"u}hrreibschweißen von d{\"u}nnen Aluminiumblechen},
  series = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  booktitle = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {Große Schweißtechnische Tagung <2012, Saarbr{\"u}cken> ; Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren},
  isbn      = {978-3-87155-593-0},
  pages     = {20 -- 25},
  year      = {2012},
  language  = {de}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrey},
  title     = {Measuring of plasma properties induced by non-vacuum electron beam welding},
  series = {Physics of plasma},
  volume    = {19},
  journal   = {Physics of plasma},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {1089-7674 (E-Journal); 1070-664X (Print)},
  doi       = {10.1063/1.3675874},
  pages     = {1 -- 7},
  year      = {2012},
  abstract  = {Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel's method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modellierung und Visualisierung der MSG-Lichtbogenprozesse},
  series = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  volume    = {64},
  journal   = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {0036-7184},
  pages     = {166 -- 174},
  year      = {2012},
  language  = {de}
}
@article{ScheikSchleserReisgen2012,
  author    = {Scheik, Sven and Schleser, Markus and Reisgen, Uwe},
  title     = {Thermisches Direktf{\"u}gen von Metall und Kusntstoff: eine Alternative zur Klebtechnik},
  series = {Adh{\"a}sion : Kleben \& Dichten},
  volume    = {56},
  journal   = {Adh{\"a}sion : Kleben \& Dichten},
  number    = {11},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0001-8198 (E-Journal); 0001-8198 (Print)},
  doi       = {10.1007/s35145-012-0005-x},
  pages     = {36 -- 40},
  year      = {2012},
  abstract  = {Im Rahmen des Exzellenzclusters „Integrative Produktionstechnik f{\"u}r Hochlohnl{\"a}nder" der RWTHAachen University werden derzeit alternative Verfahren zur Herstellung von Metall/Kunststoff- Verbindungen untersucht. Eines davon ist das thermische Direktf{\"u}gen, das eine stoffschl{\"u}ssige Verbindung zwischen Kunststoff und Metall erm{\"o}glicht und ohne die Verwendung von Klebstoffen, Haftvermittlern oder mechanischen Verbindungshilfen auskommt.},
  language  = {de}
}
@inproceedings{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Schmidt, Andre},
  title     = {SimWeld - 10 Jahre Schweißprozesssimulation im ISF},
  series = {Entwicklung und Evolution von Forschungssoftware : Tagungsband des Workshops, Rolduc, November 2011. (Aachener Informatik-Berichte, Software-Engineering ; Bd. 14)},
  booktitle = {Entwicklung und Evolution von Forschungssoftware : Tagungsband des Workshops, Rolduc, November 2011. (Aachener Informatik-Berichte, Software-Engineering ; Bd. 14)},
  editor    = {Rumpe, Bernhard and Lichter, Horst},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8440-1600-0},
  pages     = {55 -- 62},
  year      = {2012},
  language  = {de}
}
@inproceedings{QuadfliegSchoeneSchleseretal.2012,
  author    = {Quadflieg, Till and Schoene, Jens and Schleser, Markus and Jockenh{\"o}vel, Stefan and Reisgen, Uwe and Gries, Thomas},
  title     = {Shear connectors for hybrid joints of metal and FRP},
  series = {Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference},
  booktitle = {Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference},
  editor    = {Heslehurst, Rikard Benton},
  publisher = {Composites Australia},
  address   = {Hawthorne},
  isbn      = {978-0-9873285-0-2},
  pages     = {[152] -- [160]},
  year      = {2012},
  language  = {en}
}
@inproceedings{ScheikReisgenSchleseretal.2012,
  author    = {Scheik, Sven and Reisgen, Uwe and Schleser, Markus and Huber, Frederic},
  title     = {Untersuchungen zum dehnungsbasierten Versagen von geklebten, oberfl{\"a}chenveredelten Blechen im Zugscherversuch},
  series = {2. Doktorandenseminar Klebtechnik : Vortr{\"a}ge der gleichnamigen Veranstaltung in Dresden am 5. und 6. September 2011},
  booktitle = {2. Doktorandenseminar Klebtechnik : Vortr{\"a}ge der gleichnamigen Veranstaltung in Dresden am 5. und 6. September 2011},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {Institut f{\"u}r Schweißtechnik und F{\"u}getechnik Aachen> ; Doktorandenseminar Klebtechnik <2, 2011, Dresden>},
  isbn      = {978-3-87155-599-2},
  pages     = {73 -- 78},
  year      = {2012},
  language  = {de}
}
@inproceedings{ScheikReisgenSchleseretal.2012,
  author    = {Scheik, Sven and Reisgen, Uwe and Schleser, Markus and Huber, Frederic},
  title     = {Untersuchungen zum dehnungsbasierten Versagen von geklebten, oberfl{\"a}chenveredelten Blechen im Zugscherversuch},
  series = {2. Doktorandenseminar Klebtechnik : Vortr{\"a}ge der gleichnamigen Veranstaltung in Dresden am 5. und 6. September 2011. (DVS-Berichte ; 292)},
  booktitle = {2. Doktorandenseminar Klebtechnik : Vortr{\"a}ge der gleichnamigen Veranstaltung in Dresden am 5. und 6. September 2011. (DVS-Berichte ; 292)},
  publisher = {DVS Media},
  address   = {D{\"u}sseldorf},
  organization    = {Doktorandenseminar Klebtechnik <2, 2011, Dresden> ; Institut f{\"u}r Schweißtechnik und F{\"u}getechnik <Aachen>},
  isbn      = {978-3-87155-599-2},
  pages     = {73 -- 78},
  year      = {2012},
  language  = {de}
}
@inproceedings{SchoeneReisgenSchleser2012,
  author    = {Schoene, Jens and Reisgen, Uwe and Schleser, Markus},
  title     = {Verbundverhalten der polymeren Interphase in textibewehrtem Beton},
  series = {2. Doktorandenseminar Klebtechnik : Vortr{\"a}ge der gleichnamigen Veranstaltung in Dresden am 5. und 6. September 2011. (DVS-Berichte ; 292)},
  booktitle = {2. Doktorandenseminar Klebtechnik : Vortr{\"a}ge der gleichnamigen Veranstaltung in Dresden am 5. und 6. September 2011. (DVS-Berichte ; 292)},
  publisher = {DVS-Media},
  address   = {D{\"u}sseldorf},
  organization    = {Doktorandenseminar Klebtechnik <2, 2011, Dresden> ; Institut f{\"u}r Schweißtechnik und F{\"u}getechnik <Aachen>},
  isbn      = {978-3-87155-599-2},
  pages     = {50 -- 56},
  year      = {2012},
  language  = {de}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modelling and visualisation of the GMA process},
  series = {Welding and Cutting},
  volume    = {11},
  journal   = {Welding and Cutting},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {1612-3433},
  pages     = {242 -- 249},
  year      = {2012},
  language  = {en}
}
@article{ReisgenSchleserSchiebahn2013,
  author    = {Reisgen, Uwe and Schleser, Markus and Schiebahn, Alexander},
  title     = {Untersuchung zum Einfluss von Maschineneigenschaften von Schweißzangen zum Widerstandspunktschweißen auf das Schweißergebnis},
  series = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  volume    = {Bd. 65},
  journal   = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  number    = {H. 6},
  publisher = {DVS Verl.},
  address   = {D{\"u}sseldorf},
  issn      = {0036-7184},
  pages     = {309 -- 313},
  year      = {2013},
  language  = {de}
}
@article{RamazaniLiMukherjeeetal.2013,
  author    = {Ramazani, Ali and Li, Yang and Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Abdurakhmanov, Aydemir and Schleser, Markus and Reisgen, Uwe},
  title     = {Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding},
  series = {Computational materials science},
  volume    = {Vol. 68},
  journal   = {Computational materials science},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-0801 (E-Book); 0927-0256 (Print)},
  pages     = {107 -- 116},
  year      = {2013},
  language  = {en}
}
@incollection{Schleser2013,
  author    = {Schleser, Markus},
  title     = {F{\"u}gen f{\"u}r die Elektromobilit{\"a}t},
  series = {Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsf{\"a}higkeit steigert : Festschrift f{\"u}r Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.)},
  booktitle = {Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsf{\"a}higkeit steigert : Festschrift f{\"u}r Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.)},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-136-6},
  pages     = {65 -- 70},
  year      = {2013},
  language  = {de}
}
@inproceedings{ReisgenSchleserMokrovetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Schmidt, A. and Rossiter, E. and Loose, T.},
  title     = {Durchg{\"a}ngige Schweißsimulation der Eigenspannung und des Gef{\"u}gezustands auf Basis realer Schweißstromquellenparameter},
  series = {DVS congress 2010 : Große Schweißtechnische Tagung ; Studentenkongress ; Statusseminar "Schneidtechnik" ; Abschlusskolloquium zum AiF-Forschungscluster "Integration des R{\"u}hrreibschweißens in Fertigungsprozessketten" ; Vortr{\"a}ge der Veranstaltung in N{\"u}rnberg am 27. und 28. September 2010. (DVS-Berichte ; 267)},
  booktitle = {DVS congress 2010 : Große Schweißtechnische Tagung ; Studentenkongress ; Statusseminar "Schneidtechnik" ; Abschlusskolloquium zum AiF-Forschungscluster "Integration des R{\"u}hrreibschweißens in Fertigungsprozessketten" ; Vortr{\"a}ge der Veranstaltung in N{\"u}rnberg am 27. und 28. September 2010. (DVS-Berichte ; 267)},
  publisher = {DVS Media},
  address   = {D{\"u}sseldorf},
  organization    = {Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren ; Große Schweißtechnische Tagung <2010, N{\"u}rnberg>},
  isbn      = {978-3-87155-592-3},
  pages     = {37 -- 42},
  year      = {2010},
  language  = {de}
}
@book{Schleser2008,
  author    = {Schleser, Markus},
  title     = {Einsatz polymerimpr{\"a}gnierter, alkaliresistenter Glastextilien zur Bewehrung zementgebundener Matrices. (Aachener Berichte F{\"u}getechnik ; Bd. 6)},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8322-7696-6},
  pages     = {XVI, 129 S. : Ill., graph. Darst.},
  year      = {2008},
  language  = {de}
}
@techreport{Schleser2011,
  author    = {Schleser, Markus},
  title     = {Untersuchung des konduktiven R{\"u}hrreibschweißens an Stahl- und Aluminiumwerkstoffen. Schlussbericht. F{\"o}rderkennzeichen: AIF 15687 N},
  pages     = {87 S.},
  year      = {2011},
  language  = {de}
}
@inproceedings{ReisgenSchleserAbdurakhmanovetal.2009,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Amdrej V.},
  title     = {Measurement method of electron beam plasma parameters by non-vacuum electron beam welding},
  series = {Beam technologies \& laser application : proceedings of the VI international conference, Saint Petersburg, Sept. 23-25, 2009},
  booktitle = {Beam technologies \& laser application : proceedings of the VI international conference, Saint Petersburg, Sept. 23-25, 2009},
  editor    = {Turichin, G.},
  publisher = {Politechnical Univ.},
  address   = {Saint Petersburg},
  organization    = {Russian Academy of Science},
  pages     = {259 -- 267},
  year      = {2009},
  language  = {en}
}
@inproceedings{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrej},
  title     = {Application of electron beam welding to fabrication of steel-aluminium dissimilar joint},
  series = {Beam technologies \& laser application : proceedings of the VII international conference, Saint Petersburg, Sept. 18-21, 2012},
  booktitle = {Beam technologies \& laser application : proceedings of the VII international conference, Saint Petersburg, Sept. 18-21, 2012},
  publisher = {Publ. House},
  address   = {Saint Petersburg},
  pages     = {265 -- 279},
  year      = {2012},
  language  = {en}
}
@article{HemmerlingMerschenzQuackWunderlich1988,
  author    = {Hemmerling, H.-J. and Merschenz-Quack, Angelika and Wunderlich, H.},
  title     = {Crystal structures of indeno[1,2-d]imidazoles. XIth European Crystallographic Meeting, Vienna 1988},
  series = {Zeitschrift f{\"u}r Kristallographie - Crystalline Materials},
  volume    = {185},
  journal   = {Zeitschrift f{\"u}r Kristallographie - Crystalline Materials},
  number    = {H. 1-4},
  issn      = {2196-7105 (E-Books); 2194-4946 (Print)},
  pages     = {256},
  year      = {1988},
  language  = {en}
}
@inproceedings{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ufer, Sebastian and Guenel, Ismet and Gach, Stefan},
  title     = {Voruntersuchungen mit Ansys CFX zu einer Druckstufe von einem Druckstufensystem f{\"u}r das Elektronenstrahlschweißen},
  series = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  booktitle = {DVS Congress 2012 : Große Schweißtechnische Tagung, DVS-Studentenkongress ; Vortr{\"a}ge der Veranstaltungen in Saarbr{\"u}cken am 17. und 18. September 2012. (DVS-Berichte ; 286)},
  publisher = {DVS Media},
  address   = {D{\"u}sseldorf},
  organization    = {Deutscher Verband f{\"u}r Schweißen und Verwandte Verfahren ; Große Schweißtechnische Tagung <2012, Saarbr{\"u}cken>},
  isbn      = {978-3-87155-593-0},
  pages     = {33 -- 35},
  year      = {2012},
  language  = {de}
}
@inproceedings{FrickeHoffschmidt2010,
  author    = {Fricke, Barbara and Hoffschmidt, Bernhard},
  title     = {Ecobalance of a solar thermal tower power plant with volumetric receiver},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {87 -- 88},
  year      = {2010},
  language  = {en}
}
@inproceedings{SchwarzboezlPompKolletal.2010,
  author    = {Schwarzb{\"o}zl, Peter and Pomp, Stefan and Koll, Gerrit and Hennecke, Klaus and Hartz, Thomas and Schmitz, Mark and Hoffschmidt, Bernhard},
  title     = {The solar tower J{\"u}lich - first operational experiences and test results},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {8 -- 9},
  year      = {2010},
  language  = {en}
}
@inproceedings{PompSchwarzboezlKolletal.2010,
  author    = {Pomp, Stefan and Schwarzb{\"o}zl, Peter and Koll, Gerrit and Hennecke, Klaus and Schmitz, Mark and Hoffschmidt, Bernhard},
  title     = {Advanced concept for a solar thermal power plant with open volumetric air receiver},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {97 -- 98},
  year      = {2010},
  language  = {en}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Turichin, Gleb and Valdaitseva, Elena and Bach, Friedrich-Wilhelm and Hassel, Thomas and Beniyashi, Alexander},
  title     = {Investigation of factors influencing the formation of weld defects in non-vacuum electron beam welding},
  series = {The Paton welding journal},
  volume    = {2012},
  journal   = {The Paton welding journal},
  number    = {2},
  publisher = {Paton Publishing House},
  address   = {Kiev},
  issn      = {0957-798X},
  pages     = {11 -- 18},
  year      = {2012},
  abstract  = {The influence of welding condition parameters and properties of material on formation of defects, such as humping and undercuts, in non-vacuum electron beam welding was investigated. The influence of separate welding parameters on the quality of welds was determined.},
  language  = {en}
}
@inproceedings{HellmannsBoehmDilgeretal.2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus and Welters, T.},
  title     = {Neue M{\"o}glichkeiten der Klebstoffverarbeitung durch geschwindigkeitsproportionalen Handauftrag},
  series = {Adhesive bonding and hybrid bonding in body-in-white shop and assembly : proceedings, 25/26 April 2006, Bad Nauheim/Frankfurt},
  booktitle = {Adhesive bonding and hybrid bonding in body-in-white shop and assembly : proceedings, 25/26 April 2006, Bad Nauheim/Frankfurt},
  publisher = {Technik \& Kommunikation Verl.-GmbH},
  address   = {Berlin},
  pages     = {81},
  year      = {2006},
  language  = {de}
}
@inproceedings{HellmannsBoehmDilger2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus},
  title     = {Progress of the manual application of adhesives},
  series = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  booktitle = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  publisher = {Beijing Adhesion Society of China},
  address   = {Beijing},
  pages     = {275 -- 277},
  year      = {2006},
  language  = {en}
}
@inproceedings{BoehmHellmannsBackesetal.2006,
  author    = {B{\"o}hm, Stefan and Hellmanns, Mark and Backes, Andreas and Dilger, Klaus},
  title     = {Lock-in thermography based NDT of automotive parts},
  series = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  booktitle = {Proceedings of the 3rd World Congress on Adhesion and Related Phenomena : WCARP-III, October 15 -18, 2006, Beijing, China},
  publisher = {Beijing Adhesion Society of China},
  address   = {Beijing},
  pages     = {382 -- 384},
  year      = {2006},
  language  = {en}
}
@article{BoehmHellmannsBackesetal.2006,
  author    = {B{\"o}hm, Stefan and Hellmanns, Mark and Backes, Andreas and Dilger, Klaus},
  title     = {Lock-in thermography based NDT of parts for the automotive industry},
  series = {Journal of adhesion and interface},
  volume    = {Vol. 7},
  journal   = {Journal of adhesion and interface},
  number    = {No. 4},
  pages     = {10 -- 12},
  year      = {2006},
  language  = {en}
}
@inproceedings{HellmannsHartungDilgeretal.2009,
  author    = {Hellmanns, Mark and Hartung, I. and Dilger, Klaus and B{\"o}hm, Stefan},
  title     = {Quality assurance of manual guided joining and welding devices},
  series = {Proceedings of the IIW International Conference on Advances in Welding and Allied Technologies : July 16 - 17, 2009, Singapore},
  booktitle = {Proceedings of the IIW International Conference on Advances in Welding and Allied Technologies : July 16 - 17, 2009, Singapore},
  publisher = {International Institute of Welding},
  address   = {Roissy},
  isbn      = {9789810832605},
  pages     = {219 -- 222},
  year      = {2009},
  language  = {en}
}
@phdthesis{Hellmanns2012,
  author    = {Hellmanns, Mark},
  title     = {Qualit{\"a}tssicherung von handgef{\"u}hrten Applikationsprozessen durch Nachverfolgung der Handhabungseinheit. (Fortschrittsberichte aus der Produktionstechnik ; 1)},
  publisher = {Aachen},
  address   = {Shaker},
  isbn      = {978-3-8440-1379-5},
  pages     = {XIV, 99 S. : Ill., graph. Darst.},
  year      = {2012},
  language  = {de}
}
@inproceedings{HellmannsFischerDilger2013,
  author    = {Hellmanns, Mark and Fischer, F. and Dilger, Klaus},
  title     = {Applikation und Einsatz von faserverst{\"a}rkten Klebstoffen im Bauwesen},
  series = {Tagungsband / 13. Kolloquium Gemeinsame Forschung in der Klebtechnik : 26. und 27. Februar 2013, Frankfurt am Main},
  booktitle = {Tagungsband / 13. Kolloquium Gemeinsame Forschung in der Klebtechnik : 26. und 27. Februar 2013, Frankfurt am Main},
  publisher = {DECHEMA},
  address   = {Frankfurt a.M.},
  organization    = {DECHEMA, Gesellschaft f{\"u}r Chemische Technik und Biotechnologie},
  pages     = {61 -- 62},
  year      = {2013},
  language  = {de}
}
@incollection{Goldbach2013,
  author    = {Goldbach, Daniel},
  title     = {Diagnosemaßnahmen in der funktionalen Sicherheit},
  series = {Diagnose in mechatronischen Fahrzeugsystemen, VI : neue Verfahren f{\"u}r Test, Pr{\"u}fung und Diagnose von E/E-Systemen im Kfz : 7. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen". Bernhard B{\"a}ker ... (Hrsg.)},
  booktitle = {Diagnose in mechatronischen Fahrzeugsystemen, VI : neue Verfahren f{\"u}r Test, Pr{\"u}fung und Diagnose von E/E-Systemen im Kfz : 7. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen". Bernhard B{\"a}ker ... (Hrsg.)},
  publisher = {Expert Verlag},
  address   = {Renningen},
  isbn      = {978-3-8169-3221-5},
  pages     = {179 -- 198},
  year      = {2013},
  language  = {de}
}
@incollection{Goldbach2012,
  author    = {Goldbach, Daniel},
  title     = {Zuverl{\"a}ssigkeitsanalyse zur Verifikation der Einhaltung von quantitativen Sicherheitsanforderungen.},
  series = {Diagnose in mechatronischen Fahrzeugsystemen V : neue Verfahren f{\"u}r Test, Pr{\"u}fung und Diagnose von E/E-Systemen im Kfz ; [anl{\"a}sslich der 6. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen" in Dresden]. Bernard B{\"a}ker ... (Hrsg.)},
  booktitle = {Diagnose in mechatronischen Fahrzeugsystemen V : neue Verfahren f{\"u}r Test, Pr{\"u}fung und Diagnose von E/E-Systemen im Kfz ; [anl{\"a}sslich der 6. Tagung "Diagnose in Mechatronischen Fahrzeugsystemen" in Dresden]. Bernard B{\"a}ker ... (Hrsg.)},
  publisher = {Expert Verlag},
  address   = {Renningen},
  isbn      = {978-3-8169-3149-2},
  pages     = {116 -- 132},
  year      = {2012},
  language  = {de}
}
@article{BandodkarMolinnusMirzaetal.2014,
  author    = {Bandodkar, Amay J. and Molinnus, Denise and Mirza, Omar and Guinovart, Tomas and Windmiller, Joshua R. and Valdes-Ramirez, Gabriela and Andrade, Francisco J. and Sch{\"o}ning, Michael Josef and Wang, Joseph},
  title     = {Epidermal tattoo potentiometric sodium sensors with wireless signal transduction for continuous non-invasive sweat monitoring},
  series = {Biosensors and bioelectronics},
  volume    = {54},
  journal   = {Biosensors and bioelectronics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-4235 (E-Journal); 0956-5663 (Print)},
  doi       = {10.1016/j.bios.2013.11.039},
  pages     = {603 -- 609},
  year      = {2014},
  abstract  = {This article describes the fabrication, characterization and application of an epidermal temporary-transfer tattoo-based potentiometric sensor, coupled with a miniaturized wearable wireless transceiver, for real-time monitoring of sodium in the human perspiration. Sodium excreted during perspiration is an excellent marker for electrolyte imbalance and provides valuable information regarding an individual's physical and mental wellbeing. The realization of the new skin-worn non-invasive tattoo-like sensing device has been realized by amalgamating several state-of-the-art thick film, laser printing, solid-state potentiometry, fluidics and wireless technologies. The resulting tattoo-based potentiometric sodium sensor displays a rapid near-Nernstian response with negligible carryover effects, and good resiliency against various mechanical deformations experienced by the human epidermis. On-body testing of the tattoo sensor coupled to a wireless transceiver during exercise activity demonstrated its ability to continuously monitor sweat sodium dynamics. The real-time sweat sodium concentration was transmitted wirelessly via a body-worn transceiver from the sodium tattoo sensor to a notebook while the subjects perspired on a stationary cycle. The favorable analytical performance along with the wearable nature of the wireless transceiver makes the new epidermal potentiometric sensing system attractive for continuous monitoring the sodium dynamics in human perspiration during diverse activities relevant to the healthcare, fitness, military, healthcare and skin-care domains.},
  language  = {en}
}
@book{Gebhardt2013,
  author    = {Gebhardt, Andreas},
  title     = {Generative Fertigungsverfahren : Additive Manufacturing und 3D Drucken f{\"u}r Prototyping - Tooling - Produktion},
  edition   = {4., neu bearbeitete und erweiterte Auflage},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  isbn      = {978-3-446-43651-0 ; 978-3-446-43652-7},
  doi       = {10.3139/9783446436527},
  pages     = {XXIV, 637 S. : zahlr. Ill. u. graph. Darst.},
  year      = {2013},
  language  = {de}
}
@article{ReisertGeisslerFloerkeetal.2013,
  author    = {Reisert, Steffen and Geissler, Hanno and Fl{\"o}rke, Rudolf and Weiler, Christian and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Characterisation of aseptic sterilisation processes using an electronic nose},
  series = {International journal of nanotechnology},
  volume    = {Vol. 10},
  journal   = {International journal of nanotechnology},
  number    = {No. 5-7},
  publisher = {Inderscience Enterprises},
  address   = {Gen{\`e}ve},
  issn      = {1475-7435 (Print) 7141-8151 (Online)},
  pages     = {470 -- 484},
  year      = {2013},
  language  = {en}
}
@article{SchneiderSchneiderKinderetal.2013,
  author    = {Schneider, Bettina and Schneider, Wilhelm and Kinder, Stephanie and Meinhardt, Kerstin},
  title     = {Die Fallstudie: Besteuerung außerordentlicher Eink{\"u}nfte bei der Einkommensteuer},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Pr{\"u}fung, Berufseinstieg und Fortbildung},
  volume    = {42},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Pr{\"u}fung, Berufseinstieg und Fortbildung},
  number    = {11},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {1432 -- 1434},
  year      = {2013},
  language  = {de}
}
@article{Dikta2014,
  author    = {Dikta, Gerhard},
  title     = {Asymptotically efficient estimation under semi-parametric random censorship models},
  series = {Journal of multivariate analysis},
  volume    = {124},
  journal   = {Journal of multivariate analysis},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1095-7243 (E-Journal); 0047-259X (Print)},
  doi       = {10.1016/j.jmva.2013.10.002},
  pages     = {10 -- 24},
  year      = {2014},
  abstract  = {We study the estimation of some linear functionals which are based on an unknown lifetime distribution. The observations are assumed to be generated under the semi-parametric random censorship model (SRCM), that is, a random censorship model where the conditional expectation of the censoring indicator given the observation belongs to a parametric family. Under this setup a semi-parametric estimator of the survival function was introduced by the author. If the parametric model assumption is correct, it is known that the estimated functional which is based on this semi-parametric estimator is asymptotically at least as efficient as the corresponding one which rests on the nonparametric Kaplan-Meier estimator. In this paper we show that the estimated functional which is based on this semi-parametric estimator is asymptotically efficient with respect to the class of all regular estimators under this semi-parametric model.},
  language  = {en}
}
@article{DoeringKendrickLawson2013,
  author    = {D{\"o}ring, Bernd and Kendrick, C. and Lawson, R. M.},
  title     = {Thermal capacity of composite floor slabs},
  series = {Energy and buildings},
  volume    = {Vol. 67},
  journal   = {Energy and buildings},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-6178 (E-Journal); 0378-7788 (Print)},
  pages     = {531 -- 539},
  year      = {2013},
  language  = {en}
}
@article{MiyamotoHirayamaWagneretal.2013,
  author    = {Miyamoto, Ko-ichiro and Hirayama, Yuji and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Visualization of enzymatic reaction in a microfluidic channel using chemical imaging sensor},
  series = {Electrochimica acta},
  journal   = {Electrochimica acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3859 (E-Journal); 0013-4686 (Print)},
  pages     = {Publ. online},
  year      = {2013},
  language  = {en}
}
@inproceedings{StollenwerkKuvarakulKuperjans2013,
  author    = {Stollenwerk, Dominik and Kuvarakul, T. and Kuperjans, Isabel},
  title     = {Renewable energy supply for power dominated, energy intense production processes - a systematic conversion approach for the anodizing process},
  series = {IOP conference series: Earth and environmental science (EES)},
  volume    = {Vol. 16},
  booktitle = {IOP conference series: Earth and environmental science (EES)},
  number    = {H. 1},
  issn      = {1755-1315},
  pages     = {012142/1 -- 012142/4},
  year      = {2013},
  language  = {en}
}
@article{HeggerClassenSchaumannetal.2013,
  author    = {Hegger, Josef and Claßen, Martin and Schaumann, Peter and Sothmann, J{\"o}rg and Feldmann, Markus and D{\"o}ring, Bernd},
  title     = {Entwicklung einer integrierten Verbunddecke f{\"u}r nachhaltige Stahlbauten},
  series = {Stahlbau},
  volume    = {Vol. 82},
  journal   = {Stahlbau},
  number    = {Iss. 1},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1049 (E-Journal); 0038-9145 (Print)},
  pages     = {11 -- 17},
  year      = {2013},
  language  = {de}
}
@inproceedings{FeldmannPyschnyDoeringetal.2012,
  author    = {Feldmann, Markus and Pyschny, D. and D{\"o}ring, Bernd and Kuhnhenne, Markus},
  title     = {Life cycle assessment of steel constructions},
  series = {Life-cycle and sustainability of civil infrastructure systems : proceedings of the Third International Symposium on Life-Cycle Civil Engineering (IALCCE'12) : Vienna, Austria, October 3-6, 2012},
  booktitle = {Life-cycle and sustainability of civil infrastructure systems : proceedings of the Third International Symposium on Life-Cycle Civil Engineering (IALCCE'12) : Vienna, Austria, October 3-6, 2012},
  publisher = {Taylor and Francis},
  address   = {Hoboken},
  organization    = {International Symposium on Life-Cycle Civil Engineering <3, 2012, Wien>},
  isbn      = {978-0-203-10336-4},
  pages     = {321},
  year      = {2012},
  language  = {en}
}
@inproceedings{KuhnhenneDoeringPyschnyetal.2012,
  author    = {Kuhnhenne, Markus and D{\"o}ring, Bernd and Pyschny, Dominik and Feldmann, Markus},
  title     = {Energy efficient sandwich construction},
  series = {Proceedings of the VI International Congress on Architectural Envelopes : 20.6. - 22.6.2012, San Sebastian, Spain},
  booktitle = {Proceedings of the VI International Congress on Architectural Envelopes : 20.6. - 22.6.2012, San Sebastian, Spain},
  publisher = {ICAE},
  organization    = {International Congress on Architectural Envelopes <6, 2012, San Sebastian>},
  pages     = {277 -- 285},
  year      = {2012},
  language  = {en}
}
@inproceedings{DoeringKuhnhenneFeldmann2011,
  author    = {D{\"o}ring, Bernd and Kuhnhenne, Markus and Feldmann, Markus},
  title     = {Floor systems - key elements for sustainable multi-storey buildings},
  series = {SB11 Helsinki World Sustainable Building Conference : 18. - 21.10.2011},
  booktitle = {SB11 Helsinki World Sustainable Building Conference : 18. - 21.10.2011},
  organization    = {World Sustainable Building Conference <2011, Helsinki>},
  pages     = {1 -- 6},
  year      = {2011},
  language  = {en}
}
@article{HeggerClassenFeldmannetal.2011,
  author    = {Hegger, Josef and Claßen, Martin and Feldmann, Markus and D{\"o}ring, Bernd and Schaumann, Peter and Sothmann, J{\"o}rg and Bohne, Dirk and Hargus, Steen and Barben, Daniel and Aarden, Erik and Schielke, Sabine},
  title     = {Integrierte und nachhaltigkeitsorientierte Deckensysteme im Stahl- und Verbundbau},
  series = {Stahlbau},
  volume    = {Vol. 80},
  journal   = {Stahlbau},
  number    = {Iss. 10},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1049 (E-Journal); 0038-9145 (Print)},
  pages     = {728 -- 733},
  year      = {2011},
  language  = {de}
}
@article{DoeringFeldmannKuhnhenneetal.2011,
  author    = {D{\"o}ring, Bernd and Feldmann, Markus and Kuhnhenne, Markus and M{\"u}ller, Dirk},
  title     = {Phasenwechselmaterial im Metallleichtbau zur Optimierung von Energieeffizienz und sommerlicher Raumtemperatur},
  series = {Stahlbau},
  volume    = {Vol. 80},
  journal   = {Stahlbau},
  number    = {Iss. 9},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1049 (E-Journal); 0038-9145 (Print)},
  pages     = {666 -- 672},
  year      = {2011},
  language  = {de}
}
@incollection{AbelnDoeringFeldmannetal.2010,
  author    = {Abeln, Bj{\"o}rn and D{\"o}ring, Bernd and Feldmann, Markus and Geßler, Achim and M{\"o}ller, Sebastian and Paschen, Michael and Sedlacek, Gerhard},
  title     = {Entwicklungen zu Stahlfahrbahnen von Straßenbr{\"u}cken},
  series = {Festschrift zum 60. Geburtstag von Univ.-Prof. Dr.-Ing. Ingbert Mangerig. (Berichte aus dem Konstruktiven Ingenieurbau / Universit{\"a}t der Bundeswehr M{\"u}nchen ; 10/6)},
  booktitle = {Festschrift zum 60. Geburtstag von Univ.-Prof. Dr.-Ing. Ingbert Mangerig. (Berichte aus dem Konstruktiven Ingenieurbau / Universit{\"a}t der Bundeswehr M{\"u}nchen ; 10/6)},
  publisher = {Univ. der Bundeswehr},
  address   = {Neubiberg},
  pages     = {65 -- 76},
  year      = {2010},
  language  = {de}
}
@article{KuhnhenneDoeringKockeretal.2010,
  author    = {Kuhnhenne, Markus and D{\"o}ring, Bernd and Kocker, Ronald and Pyschny, Dominik and Feldmann, Markus},
  title     = {Die {\"O}kobilanz als Baustein der Nachhaltigkeitsbewertung im Industrie- und Gewerbebau},
  series = {Stahlbau},
  volume    = {79},
  journal   = {Stahlbau},
  number    = {6},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1049 (E-Journal); 0038-9145 (Print)},
  doi       = {10.1002/stab.201001336},
  pages     = {439 -- 447},
  year      = {2010},
  abstract  = {Im Herbst 2009 wurde das "Deutsche G{\"u}tesiegel Nachhaltiges Bauen" f{\"u}r die Geb{\"a}udetypen Industriebauten und Handelsbauten offiziell vorgestellt. Die {\"O}kobilanz als wichtiger Baustein der Nachhaltigkeitsbewertung wird somit auch im Industrie- und Gewerbebau zuk{\"u}nftig stark an Bedeutung gewinnen. Der vorliegende Beitrag beinhaltet einen Vergleich der Umweltleistung verschiedener Bauweisen des Industrie- und Gewerbebaus, die durch die {\"O}kobilanzierung quantifizierbar wird, anhand von momentan verf{\"u}gbaren Daten und Methoden. Es werden ausgew{\"a}hlte Ergebnisse sowie vorhandene Unsicherheiten und daraus resultierender Forschungsbedarf aufgezeigt.},
  language  = {de}
}
@article{KuhnhenneDoeringFeldmann2010,
  author    = {Kuhnhenne, Markus and D{\"o}ring, Bernd and Feldmann, Markus},
  title     = {Grunds{\"a}tze und L{\"o}sungen zur W{\"a}rmebr{\"u}ckenreduktion im Metallleichtbau},
  series = {Stahlbau},
  volume    = {79},
  journal   = {Stahlbau},
  number    = {5},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1049 (E-Journal); 0038-9145 (Print)},
  doi       = {10.1002/stab.201001330},
  pages     = {345 -- 355},
  year      = {2010},
  abstract  = {Die Anforderungen an das energiesparende Bauen sind mit der Einf{\"u}hrung der Energieeinsparverordnung (EnEV) 2009 auch im Industrie- und Gewerbebau deutlich versch{\"a}rft worden. Einen wesentlichen Beitrag zur Energieeinsparung liefert die Minimierung des Transmissionsw{\"a}rmetransfers. Analysiert man Geb{\"a}udeh{\"u}llen in Metallleichtbauweise stellt man fest, dass eine Erh{\"o}hung der W{\"a}rmed{\"a}mmst{\"a}rke allein noch nicht zielf{\"u}hrend ist, zus{\"a}tzlich sind W{\"a}rmebr{\"u}ckeneffekte zu ber{\"u}cksichtigen und deren Einfl{\"u}sse auf die W{\"a}rmetransmission zu reduzieren. Neben der Bedeutung f{\"u}r die Energieeinsparung ist eine w{\"a}rmetechnisch optimierte Detailausbildung auch erforderlich, um einen ausreichenden Feuchteschutz (Vermeidung von Tauwasser und Schimmelpilz) zu realisieren und so Sch{\"a}den zu vermeiden. Ein wichtiges Hilfsmittel stellt hierzu der vom Industrieverband f{\"u}r Bausysteme im Metallleichtbau (IFBS) herausgegebene W{\"a}rmebr{\"u}ckenatlas der Metall-Sandwichbauweise dar.},
  language  = {de}
}
@techreport{DoeringKuhnhenneVassartetal.2009,
  author    = {D{\"o}ring, Bernd and Kuhnhenne, Markus and Vassart, O. and Harper, C.},
  title     = {Integrated pre-fabricated steel technologies for the multi-storey sector},
  publisher = {Office for Official Publ. of the European Communities},
  address   = {Luxembourg},
  isbn      = {9789279113192},
  pages     = {149 S.},
  year      = {2009},
  language  = {de}
}
@article{DoeringFeldmannKuhnhenne2009,
  author    = {D{\"o}ring, Bernd and Feldmann, Markus and Kuhnhenne, Markus},
  title     = {Der Beitrag von Profilblechdecken zur passiven K{\"u}hlung},
  series = {Bauphysik},
  volume    = {Vol. 31},
  journal   = {Bauphysik},
  number    = {Iss. 2},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1437-0980 (E-Journal); 0171-5445 (Print)},
  pages     = {65 -- 71},
  year      = {2009},
  language  = {de}
}
@techreport{LaboryCajotMeesetal.2008,
  author    = {Labory, F. and Cajot, L. G. and Mees, C. and Delcuve, F. and D{\"o}ring, Bernd and Kuhnhenne, Markus and Kesti, J. and Lawson, M. and Baddoo, N. and Ogden, R. and Griffin, A. and Spasov, Y. and Bonilla, A. and Cagigal, E.},
  title     = {Energy efficient buildings through innovative systems in steel : final report. Contract No RFSR-CT-2003-00017. EUR 23180 EN},
  publisher = {European Communities},
  address   = {Luxembourg},
  organization    = {European Commission / Research Fund for Coal and Steel},
  isbn      = {978-92-79-07681-7},
  pages     = {151 S.},
  year      = {2008},
  language  = {de}
}
@techreport{KestiBurstrandKnutssonSalvatoreetal.2008,
  author    = {Kesti, J. and Burstrand Knutsson, H. and Salvatore, W. and Saouridis, C. and Odrieres Mer{\´e}, J. and Georgi, H. and Casajus, A. and Butz, C. and Schneider, R. and D{\"o}ring, Bernd},
  title     = {Dissemination of knowledge in the use of steel-intensive dry construction systems in housing : final report. Contract No RFS2-CT-2004-00036. EUR 22849 EN},
  publisher = {Office for Official Publications of the European Communities},
  address   = {Luxembourg},
  organization    = {European Commission / Research Fund for Coal and Steel},
  isbn      = {978-92-79-05973-5},
  pages     = {205 S.},
  year      = {2008},
  language  = {en}
}
@article{DoeringKuhnhenneHellbergetal.2008,
  author    = {D{\"o}ring, Bernd and Kuhnhenne, Markus and Hellberg, Jan and Feldmann, Markus},
  title     = {Aktive und passive Temperierung eines Stahldeckensystems : thermische Bauteilaktivierung : numerische und messtechnische Untersuchungen. T. 2.},
  series = {HLH L{\"u}ftung/Klima, Heizung/Sanit{\"a}r, Geb{\"a}udetechnik},
  volume    = {Bd. 59},
  journal   = {HLH L{\"u}ftung/Klima, Heizung/Sanit{\"a}r, Geb{\"a}udetechnik},
  number    = {H. 11},
  issn      = {1436-5103},
  pages     = {37 -- 41},
  year      = {2008},
  language  = {de}
}
@article{DoeringKuhnhenneHellbergetal.2008,
  author    = {D{\"o}ring, Bernd and Kuhnhenne, Markus and Hellberg, Jan and Feldmann, Markus},
  title     = {Aktive und passive Temperierung eines Stahldeckensystems : numerische und messtechnische Untersuchungen. T. 1},
  series = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik},
  volume    = {Bd. 59},
  journal   = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik},
  number    = {H. 10},
  issn      = {1436-5103, 0017-9906, 1434-422X, 1436-5103},
  pages     = {54 -- 60},
  year      = {2008},
  language  = {de}
}
@article{FeldmannDoeringKuhnhenneetal.2008,
  author    = {Feldmann, Markus and D{\"o}ring, Bernd and Kuhnhenne, Markus and Sedlacek, Gerhard},
  title     = {Zum Thema "Nachhaltigkeit" in der Stahlbauindustrie},
  series = {Stahlbau},
  volume    = {Vol. 77},
  journal   = {Stahlbau},
  number    = {Iss. 10},
  issn      = {0038-9145},
  pages     = {713 -- 720},
  year      = {2008},
  language  = {de}
}
@phdthesis{Doering2008,
  author    = {D{\"o}ring, Bernd},
  title     = {Einfluss von Deckensystemen auf Raumtemperatur und Energieeffizienz im Stahlgeschossbau. (Schriftenreihe Stahlbau. Bd. 64)},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {978-3-8322-7516-7},
  pages     = {154 S.},
  year      = {2008},
  language  = {de}
}
@inproceedings{DoeringFeldmannKuhnhenneetal.2008,
  author    = {D{\"o}ring, Bernd and Feldmann, Markus and Kuhnhenne, Markus and Hellberg, Jan},
  title     = {Implementing a thermal activation system into a light-weight steel deck element},
  series = {Eurosteel 2008 : 5th European Conference on Steel and Composite Structures ; research, practice, new materials ; 3rd to 5th September 2008, Graz, Austria / ed. by Robert Ofner ...},
  booktitle = {Eurosteel 2008 : 5th European Conference on Steel and Composite Structures ; research, practice, new materials ; 3rd to 5th September 2008, Graz, Austria / ed. by Robert Ofner ...},
  publisher = {ECCS, European Convention for Construction Steelwork},
  address   = {Brussels},
  organization    = {Eurosteel <5, 2008, Graz>},
  isbn      = {92-0147-000-90},
  pages     = {941 -- 946},
  year      = {2008},
  language  = {en}
}
@inproceedings{KuhnhenneFeldmannDoeringetal.2007,
  author    = {Kuhnhenne, Markus and Feldmann, Markus and D{\"o}ring, Bernd and Spranger, Sascha},
  title     = {Luftdichtheit im Stahlleichtbau - Geb{\"a}udeh{\"u}llen in Sandwichbauweise},
  series = {Dichte Geb{\"a}udeh{\"u}lle, Thermografie und Wohnungsl{\"u}ftung : 2. Europ{\"a}isches BlowerDoor-Symposium : 16.3. - 17.3. 2007, Kassel},
  booktitle = {Dichte Geb{\"a}udeh{\"u}lle, Thermografie und Wohnungsl{\"u}ftung : 2. Europ{\"a}isches BlowerDoor-Symposium : 16.3. - 17.3. 2007, Kassel},
  publisher = {Energie + Umwelt-Zentrum},
  organization    = {Europ{\"a}isches BlowerDoor-Symposium <2, 2007, Kassel>},
  pages     = {121 -- 134},
  year      = {2007},
  language  = {de}
}
@inproceedings{SpasovDoeringGriffin2007,
  author    = {Spasov, Yulian and D{\"o}ring, Bernd and Griffin, Allan},
  title     = {Exploiting the thermal mass in an energy efficient building - a comparison exercise between IES Apache and TRNSYS models},
  series = {Clima 2007 WellBeing Indoors: 9th Rehva World Congress, 10-14 June 2007, Helsinki, Finland : proceedings},
  booktitle = {Clima 2007 WellBeing Indoors: 9th Rehva World Congress, 10-14 June 2007, Helsinki, Finland : proceedings},
  address   = {Helsinki},
  isbn      = {978-952-99898-2-9},
  pages     = {1 -- 7},
  year      = {2007},
  language  = {en}
}
@inproceedings{DoeringFeldmannKuhnhenne2007,
  author    = {D{\"o}ring, Bernd and Feldmann, Markus and Kuhnhenne, Markus},
  title     = {An innovative thermally activated light-weight steel deck system - numerical investigations and practical tests},
  series = {Clima 2007 WellBeing Indoors: 9th Rehva World Congress, 10-14 June 2007, Helsinki, Finland : proceedings},
  booktitle = {Clima 2007 WellBeing Indoors: 9th Rehva World Congress, 10-14 June 2007, Helsinki, Finland : proceedings},
  address   = {Helsinki},
  isbn      = {978-952-99898-2-9},
  pages     = {1 -- 8},
  year      = {2007},
  language  = {en}
}
@techreport{ConanD'HaeyerBeguinetal.2006,
  author    = {Conan, Yulian and D'Haeyer, R. and B{\´e}guin, P. and D{\"o}ring, Bernd and Kuhnhenne, Markus and Bayo, E.},
  title     = {Steel in low-rise building : a symbiosis of cold formed sections and light rolled profiles : final report. Contract-No. 7215-PP/070. EUR 22080 en},
  publisher = {Office for Official Publications of the European Communities},
  address   = {Luxembourg},
  isbn      = {92-79-02082-X},
  pages     = {200 S.},
  year      = {2006},
  language  = {en}
}
@inproceedings{DoeringSedlacek2004,
  author    = {D{\"o}ring, Bernd and Sedlacek, Gerhard},
  title     = {Improvement of thermal comfort in light weight buildings made of steel with new concepts for slab systems},
  series = {10th Nordic Steel Construction Conference, Copenhagen, Denmark 7-9. June 2004: NSCC 2004 : proceedings},
  booktitle = {10th Nordic Steel Construction Conference, Copenhagen, Denmark 7-9. June 2004: NSCC 2004 : proceedings},
  publisher = {Danish Steel Inst.},
  address   = {Copenhagen},
  organization    = {Nordic Steel Construction Conference <10, 2004, Copenhagen>},
  pages     = {35 -- 44},
  year      = {2004},
  language  = {en}
}
@article{DoeringHechlerWeberetal.2004,
  author    = {D{\"o}ring, Bernd and Hechler, O. and Weber, F. and Sedlacek, Gerhard},
  title     = {Thermische Aktivierung von Fertigteildecken},
  series = {HLH L{\"u}ftung/Klima, Heizung/Sanit{\"a}r, Geb{\"a}udetechnik},
  volume    = {Jg. 55},
  journal   = {HLH L{\"u}ftung/Klima, Heizung/Sanit{\"a}r, Geb{\"a}udetechnik},
  number    = {Nr. 5},
  issn      = {1436-5103},
  pages     = {24 -- 35},
  year      = {2004},
  language  = {de}
}
@article{ZillerDoering2004,
  author    = {Ziller, Claudia and D{\"o}ring, Bernd},
  title     = {Doppelfassaden - vom Experimentalmodell zum Massanzug},
  series = {TAB Technik am Bau},
  volume    = {Bd. 35},
  journal   = {TAB Technik am Bau},
  number    = {H. 12},
  issn      = {0341-2032},
  pages     = {58 -- 63},
  year      = {2004},
  language  = {de}
}
@book{SedlacekZillerWeynandetal.2004,
  author    = {Sedlacek, Gerhard and Ziller, Claudia and Weynand, Klaus and Stark, Sebastian and Thiel, Dieter and Lemke, H.-J. and D{\"o}ring, Bernd and Lenzen, Kersten},
  title     = {Integration von Tragwerk und Haustechnik in B{\"u}ro- und Produktionsgeb{\"a}uden aus Stahl f{\"u}r eine flexible Nutzung : Forschungsvorhaben. (Forschung f{\"u}r die Praxis : Projekt ; P 447)},
  publisher = {Forschungsvereinigung Stahlanwendung e.V. -FOSTA-},
  address   = {D{\"u}sseldorf},
  isbn      = {9783937567051},
  pages     = {103 S.},
  year      = {2004},
  language  = {de}
}
@inproceedings{DoeringZillerHortmanns2003,
  author    = {D{\"o}ring, Bernd and Ziller, Claudia and Hortmanns, M.},
  title     = {Ventilation of double facades by external dynamic wind pressure},
  series = {11th International Conference on Wind Engineering. 1},
  booktitle = {11th International Conference on Wind Engineering. 1},
  publisher = {The Wind Science and Engineering Research Center},
  address   = {Lubbock, Tex.},
  organization    = {International Conference on Wind Engineering <11, 2003, Lubbock, Tex.>},
  pages     = {721 -- 730},
  year      = {2003},
  language  = {en}
}
@inproceedings{ZillerDoering2003,
  author    = {Ziller, Claudia and D{\"o}ring, Bernd},
  title     = {Influence of the external dynamic wind pressure on the ventilation of double facades},
  series = {Research in building physics: proceedings of the Second International Conference on Building Physics : Leuven, Belgium, 14-18 September 2003},
  booktitle = {Research in building physics: proceedings of the Second International Conference on Building Physics : Leuven, Belgium, 14-18 September 2003},
  editor    = {Carmeliet, J. and Hens, H. and Vermeir, G.},
  publisher = {Taylor and Francis},
  address   = {Hoboken},
  organization    = {International Conference on Building Physics <2, 2003, Leuven>},
  isbn      = {9058095657, 9789058095657},
  pages     = {527 -- 533},
  year      = {2003},
  language  = {en}
}
@article{ThielDoering2001,
  author    = {Thiel, Dieter and D{\"o}ring, Bernd},
  title     = {Dezentrale Raumklimatisierung durch die Fassade},
  series = {TAB Technik am Bau},
  volume    = {Bd. 32},
  journal   = {TAB Technik am Bau},
  number    = {H. 3},
  issn      = {0341-2032},
  pages     = {67 -- 76},
  year      = {2001},
  language  = {de}
}
@techreport{Doering1997,
  author    = {D{\"o}ring, Bernd},
  title     = {Nutzung erneuerbarer Energien in Landesbauten : Dokumentation realisierter und geplanter Anlagen},
  publisher = {Landesinstitut f{\"u}r Bauwesen des Landes Nordrhein-Westfalen},
  address   = {Aachen},
  isbn      = {3-930860-51-1},
  pages     = {66 S.},
  year      = {1997},
  language  = {de}
}
@article{KuckDoering1997,
  author    = {Kuck, Herbert and D{\"o}ring, Bernd},
  title     = {Regenerative Energien in Landesbauten : Land NRW unterst{\"u}tzt Einsatz erneuerbarer Energien 1997 mit 15 Mio. DM},
  series = {Die Bauverwaltung mit Bauamt und Gemeindebau},
  volume    = {Bd. 70},
  journal   = {Die Bauverwaltung mit Bauamt und Gemeindebau},
  number    = {H. 8},
  issn      = {0005-6847},
  pages     = {384 -- 386},
  year      = {1997},
  language  = {de}
}
@phdthesis{Kotliar2012,
  author    = {Kotliar, Konstantin},
  title     = {Pathophysiologische Beurteilung und h{\"a}modynamische Analyse von mikrostrukturellen Ver{\"a}nderungen des retinalen Gef{\"a}ßl{\"a}ngsschnittsprofils},
  pages     = {328 S.},
  year      = {2012},
  language  = {ru}
}
@incollection{LanzlSeidovaDuehringetal.2009,
  author    = {Lanzl, I. and Seidova, S.-F. and D{\"u}hring, C. von and Kotliar, Konstantin},
  title     = {Befunde der dynamischen Gef{\"a}ßanalyse am Auge bei Gesunden und Glaukom-Patienten mit praxisrelevanter Bedeutung},
  series = {Mikrozirkulation beim Glaukom},
  booktitle = {Mikrozirkulation beim Glaukom},
  editor    = {Erb, Carl},
  publisher = {Elsevier},
  address   = {Amsterdam},
  pages     = {33 -- 39},
  year      = {2009},
  language  = {de}
}
@misc{IngebrandtWagnerSchoening2013,
  author    = {Ingebrandt, Sven and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Engineering of functional interfaces / guest eds. Sven Ingebrandt ; Patrick Wagner ; Michael J. Sch{\"o}ning},
  series = {Physica Status Solidi (A)},
  volume    = {Vol. 210},
  journal   = {Physica Status Solidi (A)},
  number    = {Iss. 5},
  issn      = {1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)},
  pages     = {845},
  year      = {2013},
  language  = {en}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@inproceedings{SpohrSchirraHoeflingetal.2013,
  author    = {Spohr, A. and Schirra, Julian and Hoefling, J. and Schedl, A.},
  title     = {Wing weight estimation methodology for highly non-planar lifting systems during conceptual design},
  series = {Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart},
  organization    = {Deutscher Luft- und Raumfahrtkongress <62, 2013, Stuttgart>},
  pages     = {Publ. online},
  year      = {2013},
  language  = {en}
}
@inproceedings{HoeflingSchirraSpohretal.2013,
  author    = {Hoefling, J. and Schirra, Julian and Spohr, A. and Sch{\"a}fer, D.},
  title     = {Induced drag computation with wake model schemes for highly non-planar wing systems},
  series = {Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2013 : 10.9. - 12.9.2013, Stuttgart},
  publisher = {Dt. Ges. f{\"u}r Luft- und Raumfahrt},
  address   = {Bonn},
  organization    = {Deutscher Luft- und Raumfahrtkongress <62, 2013, Stuttgart>},
  pages     = {1 -- 10},
  year      = {2013},
  language  = {en}
}
@book{SchmidtMuellerStoecker1993,
  author    = {Schmidt, Ludwig and M{\"u}ller, Thomas and St{\"o}cker, Ernst E.},
  title     = {Die Organschaft im K{\"o}rperschaftsteuer-, Gewerbesteuer- und Umsatzsteuerrecht},
  edition   = {4. Aufl.},
  publisher = {Verl. Neue Wirtschafts-Briefe},
  address   = {Herne},
  isbn      = {3-482-44604-0},
  pages     = {393 S.},
  year      = {1993},
  language  = {de}
}
@book{SchmidtMuellerStoecker1999,
  author    = {Schmidt, Ludwig and M{\"u}ller, Thomas and St{\"o}cker, Ernst E.},
  title     = {Die Organschaft im K{\"o}rperschaftsteuer-, Gewerbesteuer- und Umsatzsteuerrecht},
  edition   = {5. Aufl.},
  publisher = {Verl. Neue Wirtschafts-Briefe},
  address   = {Herne},
  isbn      = {3-482-44605-9},
  pages     = {423 S.},
  year      = {1999},
  language  = {de}
}
@book{SchmidtMuellerStoecker2003,
  author    = {Schmidt, Ludwig and M{\"u}ller, Thomas and St{\"o}cker, Ernst E.},
  title     = {Die Organschaft im K{\"o}rperschaftsteuer-, Gewerbesteuer- und Umsatzsteuerrecht},
  edition   = {6. Aufl.},
  publisher = {Verl. Neue Wirtschafts-Briefe},
  address   = {Herne},
  isbn      = {3-482-44606-7},
  pages     = {429 S.},
  year      = {2003},
  language  = {de}
}
@book{MuellerStoecker2008,
  author    = {M{\"u}ller, Thomas and St{\"o}cker, Ernst E.},
  title     = {Die Organschaft : K{\"o}rperschaftsteuerrecht, Gewerbesteuerrecht, Umsatzsteuerrecht},
  edition   = {7. Aufl.},
  publisher = {NWB Verl.},
  address   = {Herne},
  isbn      = {978-3-482-44607-8},
  pages     = {443 S.},
  year      = {2008},
  language  = {de}
}
@article{Knueppel2012,
  author    = {Kn{\"u}ppel, Mark},
  title     = {Außerbilanzielle Korrekturen},
  series = {Handbuch der Bilanzierung online},
  journal   = {Handbuch der Bilanzierung online},
  editor    = {Federmann, Rudolf and Kußmaul, Heinz and M{\"u}ller, Stefan},
  publisher = {Haufe},
  address   = {Freiburg},
  issn      = {0172-0392},
  pages     = {Artikel HI 1380074},
  year      = {2012},
  language  = {de}
}
@book{BuyerKleinMueller2010,
  author    = {Buyer, Christoph and Klein, Hartmut and M{\"u}ller, Thomas},
  title     = {{\"A}nderung der Unternehmensform : Handbuch zum Umwandlungs- und Umwandlungssteuerrecht},
  edition   = {8. Aufl.},
  publisher = {Verl. Neue Wirtschafts-Briefe},
  address   = {Herne},
  isbn      = {978-3-482-42258-4},
  pages     = {XL, 585 S.},
  year      = {2010},
  language  = {de}
}
@misc{AbdelghaniMenaaObareetal.2013,
  author    = {Abdelghani, Adnane and Menaa, Bouzid and Obare, Sherine O. and Sch{\"o}ning, Michael Josef},
  title     = {Special issue on nanoscale science and technology / guest eds.: Adnane Abdelghani, Bouzid Menaa, Sherine O. Obare, Michael J. Sch{\"o}ning},
  series = {International journal of nanotechnology},
  volume    = {Vol. 10},
  journal   = {International journal of nanotechnology},
  number    = {No. 5-7},
  issn      = {1741-8151 (E-Journal), 1475-7435 (Print)},
  pages     = {373 -- 619},
  year      = {2013},
  language  = {en}
}