@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrey},
  title     = {Measuring of plasma properties induced by non-vacuum electron beam welding},
  series = {Physics of plasma},
  volume    = {19},
  journal   = {Physics of plasma},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {1089-7674 (E-Journal); 1070-664X (Print)},
  doi       = {10.1063/1.3675874},
  pages     = {1 -- 7},
  year      = {2012},
  abstract  = {Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel's method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.},
  language  = {en}
}
@article{MukherjeeRamazaniYangetal.2011,
  author    = {Mukherjee, Krishnendu and Ramazani, Ali and Yang, Li and Prahl, Ulrich and Bleck, Wolfgang and Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir},
  title     = {Characterization of gas metal arc welded hot rolled DP600 steel},
  series = {Steel research international},
  volume    = {Vol. 82},
  journal   = {Steel research international},
  number    = {Iss. 12},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1869-344X (E-Book); 1611-3683 (Print)},
  pages     = {1408 -- 1416},
  year      = {2011},
  language  = {en}
}
@article{GlowaniaGriesSchoeneetal.2011,
  author    = {Glowania, Michael and Gries, Thomas and Schoene, Jens and Schleser, Markus and Reisgen, Uwe},
  title     = {Innovative coating technology for textile reinforcements of concrete applications},
  series = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)},
  journal   = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  organization    = {International Congress Polymers in Concrete <13, 2010, Funchal, Madeira>},
  isbn      = {978-3-03785-008-4},
  issn      = {1013-9826 (E-Journal) ; 0252-1059 (Print)},
  pages     = {167 -- 173},
  year      = {2011},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2011,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Numerical and experimental investigation of tensile behavior of laser beam welded TRIP700 steel},
  series = {ISIJ international},
  volume    = {Vol. 51},
  journal   = {ISIJ international},
  number    = {No. 3},
  publisher = {ISIJ},
  address   = {Tōkyō},
  organization    = {Iron and Steel Institute of Japan (ISIJ)},
  issn      = {1347-5460 (E-Journal); 0915-1559 (Print)},
  pages     = {429 -- 434},
  year      = {2011},
  language  = {en}
}
@article{RoesnerScheikOlowinskyetal.2011,
  author    = {Roesner, Andreas and Scheik, Sven and Olowinsky, Alexander and Gillner, Arnold and Propawe, Reinhart and Schleser, Markus and Reisgen, Uwe},
  title     = {Innovative approach of joining hybrid components},
  series = {Journal of laser applications},
  volume    = {Vol. 23},
  journal   = {Journal of laser applications},
  number    = {Iss. 3},
  publisher = {Laser Institute of America},
  address   = {Orlando, Fla.},
  issn      = {1042-346X},
  pages     = {32007},
  year      = {2011},
  language  = {en}
}
@article{RoesnerScheikOlowinskyetal.2011,
  author    = {Roesner, Andreas and Scheik, Sven and Olowinsky, Alexander and Gillner, Arnold and Reisgen, Uwe and Schleser, Markus},
  title     = {Laser assisted joining of plastic metal hybrids},
  series = {Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B)},
  journal   = {Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  organization    = {International WLT Conference on Lasers in Manufacturing <6, M{\"u}nchen, 2011>},
  issn      = {1875-3892 (E-Journal); 1875-3884 (Print)},
  pages     = {370 -- 377},
  year      = {2011},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2011,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander},
  title     = {Virtual welding equipment for simulation of GMAW processes with integration of power source regulation},
  series = {Frontiers of materials science},
  volume    = {Vol. 5},
  journal   = {Frontiers of materials science},
  number    = {Iss. 2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2095-0268 (E-Journal); 2095-025X (Print)},
  pages     = {79 -- 89},
  year      = {2011},
  language  = {en}
}
@article{SchleserWalkLaufferRaupachetal.2006,
  author    = {Schleser, Markus and Walk-Lauffer, Bernd and Raupach, Michael and Dilthey, Ulrich},
  title     = {Application of polymers for textile-reinforced concrete},
  series = {Journal of materials in civil engineering : properties, applications, durability},
  volume    = {18},
  journal   = {Journal of materials in civil engineering : properties, applications, durability},
  number    = {5},
  issn      = {0899-1561},
  pages     = {670 -- 676},
  year      = {2006},
  language  = {en}
}
@article{FeldmannPakGessleretal.2006,
  author    = {Feldmann, Markus and Pak, Daniel and Geßler, Achim and Dilthey, Ulrich and Schleser, Markus},
  title     = {Bonded connections for textile reinforced concrete structures},
  series = {Cailiao-gongcheng = Journal of materials engineering},
  journal   = {Cailiao-gongcheng = Journal of materials engineering},
  number    = {Special iss.},
  issn      = {1001-4381},
  pages     = {123 -- 127},
  year      = {2006},
  language  = {en}
}
@article{DiltheySchleserFeldmannetal.2008,
  author    = {Dilthey, Ulrich and Schleser, Markus and Feldmann, Martin and Pak, Daniel and Geßler, Achim},
  title     = {Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts},
  series = {Cement and concrete composites},
  volume    = {Vol. 30},
  journal   = {Cement and concrete composites},
  number    = {iss. 2},
  issn      = {0958-9465},
  pages     = {82 -- 87},
  year      = {2008},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modelling and visualisation of the GMA process},
  series = {Welding and Cutting},
  volume    = {11},
  journal   = {Welding and Cutting},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {1612-3433},
  pages     = {242 -- 249},
  year      = {2012},
  language  = {en}
}
@article{RamazaniLiMukherjeeetal.2013,
  author    = {Ramazani, Ali and Li, Yang and Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Abdurakhmanov, Aydemir and Schleser, Markus and Reisgen, Uwe},
  title     = {Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding},
  series = {Computational materials science},
  volume    = {Vol. 68},
  journal   = {Computational materials science},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-0801 (E-Book); 0927-0256 (Print)},
  pages     = {107 -- 116},
  year      = {2013},
  language  = {en}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@article{FateriGebhardtThuemmleretal.2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Th{\"u}mmler, Stefan and Thurn, Laura},
  title     = {Experimental investigation on selective laser melting of glass},
  series = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  volume    = {56 (2014)},
  journal   = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892 (E-Journal); 1875-3884 (Print)},
  doi       = {10.1016/j.phpro.2014.08.118},
  pages     = {357 -- 364},
  year      = {2014},
  language  = {en}
}
@article{PfaffBurnham2009,
  author    = {Pfaff, Raphael and Burnham, Keith J.},
  title     = {On abstraction and interpretability: a behavioural perspective},
  series = {Systems Science},
  volume    = {Vol. 35},
  journal   = {Systems Science},
  number    = {Iss. 2},
  issn      = {0137-1223},
  pages     = {19 -- 26},
  year      = {2009},
  language  = {en}
}
@article{SeilerPichlerPfaffetal.2009,
  author    = {Seiler, Friedrich and Pichler, Alexander and Pfaff, Raphael and Srulijes, Julio},
  title     = {Novel processing tools for automated doppler picture velocimetry (DPV) evaluation},
  series = {Journal of visualization},
  volume    = {Vol. 12},
  journal   = {Journal of visualization},
  number    = {Iss. 4},
  issn      = {1343-8875},
  pages     = {323 -- 337},
  year      = {2009},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective Laser Melting of Soda-Lime Glass Powder},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1744-7402},
  doi       = {10.1111/ijac.12338},
  pages     = {53 -- 61},
  year      = {2015},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Process Parameters Development of Selective Laser Melting of Lunar Regolith for On-Site Manufacturing Applications},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  isbn      = {1744-7402},
  doi       = {10.1111/ijac.12326},
  pages     = {46 -- 52},
  year      = {2015},
  language  = {en}
}
@article{KaemperPicardBrilletal.2003,
  author    = {K{\"a}mper, Klaus-Peter and Picard, Antoni and Brill, Manfred and Cassel, Detlev and Jentsch, Andreas and Merten, Sabine and Rollwa, Markus},
  title     = {The Virtual Clean Room - a new tool in teaching MST process technologies},
  year      = {2003},
  abstract  = {The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room.},
  subject      = {Virtuelle Maschine},
  language  = {en}
}
@article{Gebhardt2006,
  author    = {Gebhardt, Andreas},
  title     = {Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping"},
  year      = {2006},
  abstract  = {Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering - Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision},
  subject      = {Rapid prototyping},
  language  = {en}
}