@article{MiyamotoItabashiWagneretal.2014,
  author    = {Miyamoto, Ko-ichiro and Itabashi, Akinori and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {High-speed chemical imaging inside a microfluidic channel},
  series = {Sensors and actuators. B: Chemical},
  volume    = {194},
  journal   = {Sensors and actuators. B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2013.12.090},
  pages     = {521 -- 527},
  year      = {2014},
  abstract  = {In this study, a high-speed chemical imaging system was developed for visualization of the interior of a microfluidic channel. A microfluidic channel was constructed on the sensor surface of the light-addressable potentiometric sensor (LAPS), on which the ion concentrations could be measured in parallel at up to 64 points illuminated by optical fibers. The temporal change of pH distribution inside the microfluidic channel was recorded at a maximum rate of 100 frames per second (fps). The high frame rate allowed visualization of moving interfaces and plugs in the channel even at a flow velocity of 111 mm/s, which suggests the feasibility of plug-based microfluidic devices for flow-injection analysis (FIA).},
  language  = {en}
}
@article{SiqueiraMolinnusBegingetal.2014,
  author    = {Siqueira, Jose R. and Molinnus, Denise and Beging, Stefan and Sch{\"o}ning, Michael Josef},
  title     = {Incorporating a hybrid urease-carbon nanotubes sensitive nanofilm on capacitive field-effect sensors for urea detection},
  series = {Analytical chemistry},
  volume    = {86},
  journal   = {Analytical chemistry},
  number    = {11},
  publisher = {ACS Publications},
  address   = {Columbus},
  issn      = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)},
  doi       = {10.1021/ac500458s},
  pages     = {5370 -- 5375},
  year      = {2014},
  abstract  = {The ideal combination among biomolecules and nanomaterials is the key for reaching biosensing units with high sensitivity. The challenge, however, is to find out a stable and sensitive film architecture that can be incorporated on the sensor's surface. In this paper, we report on the benefits of incorporating a layer-by-layer (LbL) nanofilm of polyamidoamine (PAMAM) dendrimer and carbon nanotubes (CNTs) on capacitive electrolyte-insulator-semiconductor (EIS) field-effect sensors for detecting urea. Three sensor arrangements were studied in order to investigate the adequate film architecture, involving the LbL film with the enzyme urease: (i) urease immobilized directly onto a bare EIS [EIS-urease] sensor; (ii) urease atop the LbL film over the EIS [EIS-(PAMAM/CNT)-urease] sensor; and (iii) urease sandwiched between the LbL film and another CNT layer [EIS-(PAMAM/CNT)-urease-CNT]. The surface morphology of all three urea-based EIS biosensors was investigated by atomic force microscopy (AFM), while the biosensing abilities were studied by means of capacitance-voltage (C/V) and dynamic constant-capacitance (ConCap) measureaments at urea concentrations ranging from 0.1 mM to 100 mM. The EIS-urease and EIS-(PAMAM/CNT)-urease sensors showed similar sensitivity (∼18 mV/decade) and a nonregular signal behavior as the urea concentration increased. On the other hand, the EIS-(PAMAM/CNT)-urease-CNT sensor exhibited a superior output signal performance and higher sensitivity of about 33 mV/decade. The presence of the additional CNT layer was decisive to achieve a urea based EIS sensor with enhanced properties. Such sensitive architecture demonstrates that the incorporation of an adequate hybrid enzyme-nanofilm as sensing unit opens new prospects for biosensing applications using the field-effect sensor platform.},
  language  = {en}
}
@article{GuoMiyamotoWagneretal.2014,
  author    = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor for the investigation of the spatial resolution},
  series = {Sensors and actuators B: Chemical},
  volume    = {204},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.08.016},
  pages     = {659 -- 665},
  year      = {2014},
  abstract  = {As a semiconductor-based electrochemical sensor, the light-addressable potentiometric sensor (LAPS) can realize two dimensional visualization of (bio-)chemical reactions at the sensor surface addressed by localized illumination. Thanks to this imaging capability, various applications in biochemical and biomedical fields are expected, for which the spatial resolution is critically significant. In this study, therefore, the spatial resolution of the LAPS was investigated in detail based on the device simulation. By calculating the spatiotemporal change of the distributions of electrons and holes inside the semiconductor layer in response to a modulated illumination, the photocurrent response as well as the spatial resolution was obtained as a function of various parameters such as the thickness of the Si substrate, the doping concentration, the wavelength and the intensity of illumination. The simulation results verified that both thinning the semiconductor substrate and increasing the doping concentration could improve the spatial resolution, which were in good agreement with known experimental results and theoretical analysis. More importantly, new findings of interests were also obtained. As for the dependence on the wavelength of illumination, it was found that the known dependence was not always the case. When the Si substrate was thick, a longer wavelength resulted in a higher spatial resolution which was known by experiments. When the Si substrate was thin, however, a longer wavelength of light resulted in a lower spatial resolution. This finding was explained as an effect of raised concentration of carriers, which reduced the thickness of the space charge region. The device simulation was found to be helpful to understand the relationship between the spatial resolution and device parameters, to understand the physics behind it, and to optimize the device structure and measurement conditions for realizing higher performance of chemical imaging systems.},
  language  = {en}
}
@article{ReisertGeisslerWeileretal.2015,
  author    = {Reisert, Steffen and Geissler, H. and Weiler, C. and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Multiple sensor-type system for monitoring the microbicidal effectiveness of aseptic sterilisation processes},
  series = {Food control},
  volume    = {47},
  journal   = {Food control},
  issn      = {1873-7129 (E-Journal); 0956-7135 (Print)},
  doi       = {10.1016/j.foodcont.2014.07.063},
  pages     = {615 -- 622},
  year      = {2015},
  abstract  = {The present work describes a novel multiple sensor-type system for the real-time analysis of aseptic sterilisation processes employing gaseous hydrogen peroxide (H2O2) as a sterilant. The inactivation kinetics of Bacillus atrophaeus by gaseous H2O2 have been investigated by means of a methodical calibration experiment, taking into account the process variables H2O2 concentration, humidity and gas temperature. It has been found that the microbicidal effectiveness at H2O2 concentrations above 2\% v/v is largely determined by the concentration itself, while at lower H2O2 concentrations, the gas temperature and humidity play a leading role. Furthermore, the responses of different types of gas sensors towards the influencing factors of the sterilisation process have been analysed within the same experiment. Based on a correlation established between the inactivation kinetics and the sensor responses, a calorimetric H2O2 sensor and a metal-oxide semiconductor (MOX) sensor have been identified as possible candidates for monitoring the microbicidal effectiveness of aseptic sterilisation processes employing gaseous H2O2. Therefore, two linear models that describe the relationship between sensor response and microbicidal effectiveness have been proposed.},
  language  = {en}
}
@article{KhaydukovaZadorozhnayaKirsanovetal.2014,
  author    = {Khaydukova, M. M. and Zadorozhnaya, O. A. and Kirsanov, D. O. and Iken, Heiko and Rolka, David and Sch{\"o}ning, Michael Josef and Babain, V. A. and Vlasov, Yu. G. and Legin, A. V.},
  title     = {Multivariate processing of atomic-force microscopy images for detection of the response of plasticized polymeric membranes},
  series = {Russian journal of applied chemistry},
  volume    = {87},
  journal   = {Russian journal of applied chemistry},
  number    = {3},
  publisher = {Springer},
  address   = {Dordrecht},
  issn      = {1608-3296 (E-Journal); 1070-4272 (Print)},
  doi       = {10.1134/S1070427214030112},
  pages     = {307 -- 314},
  year      = {2014},
  abstract  = {The possibility of using the atomic-force microscopy as a method for detection of the analytical signal from plasticized polymeric sensor membranes was analyzed. The surfaces of cadmium-selective membranes based on two polymeric matrices were examined. The digital images were processed with multivariate image analysis techniques. A correlation was found between the surface profile of an ion-selective membrane and the concentration of the ion in solution.},
  language  = {en}
}
@article{SchusserPoghossianBaeckeretal.2015,
  author    = {Schusser, Sebastian and Poghossian, Arshak and B{\"a}cker, Matthias and Krischer, M. and Leinhos, Marcel and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {An application of field-effect sensors for in-situ monitoring of degradation of biopolymers},
  series = {Sensors and actuators B: Chemical},
  volume    = {207, Part B},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.10.058},
  pages     = {954 -- 959},
  year      = {2015},
  abstract  = {The characterization of the degradation kinetics of biodegradable polymers is mandatory with regard to their proper application. In the present work, polymer-modified electrolyte-insulator-semiconductor (PMEIS) field-effect sensors have been applied for in-situ monitoring of the pH-dependent degradation kinetics of the commercially available biopolymer poly(d,l-lactic acid) (PDLLA) in buffer solutions from pH 3 to pH 13. PDLLA films of 500 nm thickness were deposited on the surface of an Al-p-Si-SiO2-Ta2O5 structure from a polymer solution by means of spin-coating method. The PMEIS sensor is, in principle, capable to detect any changes in bulk, surface and interface properties of the polymer induced by degradation processes. A faster degradation has been observed for PDLLA films exposed to alkaline solutions (pH 9, pH 11 and pH 13).},
  language  = {en}
}
@article{YoshinobuMiyamotoWagneretal.2015,
  author    = {Yoshinobu, Tatsuo and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Recent developments of chemical imaging sensor systems based on the principle of the light-addressable potentiometric sensor},
  series = {Sensors and actuators B: Chemical},
  volume    = {207, Part B},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.09.002},
  pages     = {926 -- 932},
  year      = {2015},
  abstract  = {The light-addressable potentiometric sensor (LAPS) is an electrochemical sensor with a field-effect structure to detect the variation of the Nernst potential at its sensor surface, the measured area on which is defined by illumination. Thanks to this light-addressability, the LAPS can be applied to chemical imaging sensor systems, which can visualize the two-dimensional distribution of a particular target ion on the sensor surface. Chemical imaging sensor systems are expected to be useful for analysis of reaction and diffusion in various electrochemical and biological samples. Recent developments of LAPS-based chemical imaging sensor systems, in terms of the spatial resolution, measurement speed, image quality, miniaturization and integration with microfluidic devices, are summarized and discussed.},
  language  = {en}
}
@article{MuribYeapMartensetal.2015,
  author    = {Murib, M. S. and Yeap, W. S. and Martens, D. and Liu, X. and Bienstman, P. and Fahlman, M. and Sch{\"o}ning, Michael Josef and Michiels, L. and Haenen, K. and Serpeng{\"u}zel, A. and Wagner, Patrick},
  title     = {Photonic studies on polymer-coated sapphire-spheres : a model system for biological ligands},
  series = {Sensors and actuators A: Physical},
  volume    = {222},
  journal   = {Sensors and actuators A: Physical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3069 (E-Journal); 0924-4247 (Print)},
  doi       = {10.1016/j.sna.2014.11.024},
  pages     = {212 -- 219},
  year      = {2015},
  abstract  = {In this study we show an optical biosensor concept, based on elastic light scattering from sapphire microspheres. Transmitted and elastic scattering intensity of the microspheres (radius 500 μm, refractive index 1.77) on an optical fiber half coupler is analyzed at 1510 nm. The 0.43 nm angular mode spacing of the resonances is comparable to the angular mode spacing value estimated using the optical size of the microsphere. The spectral linewidths of the resonances are in the order of 0.01 nm, which corresponds to quality factors of approximately 105. A polydopamine layer is used as a functionalizing agent on sapphire microspherical resonators in view of biosensor implementation. The varying layer thickness on the microsphere is determined as a function of the resonance wavelength shift. It is shown that polymer functionalization has a minor effect on the quality factor. This is a promising step toward the development of an optical biosensor.},
  language  = {en}
}
@article{MiyamotoSekiWagneretal.2014,
  author    = {Miyamoto, K. and Seki, K. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Enhancement of the spatial resolution of the chemical imaging sensor by a hybrid fiber-optic illumination},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.563},
  pages     = {612 -- 615},
  year      = {2014},
  abstract  = {The chemical imaging sensor, which is based on the principle of the light-addressable potentiometric sensor (LAPS), is a powerful tool to visualize the spatial distribution of chemical species on the sensor surface. The spatial resolution of this sensor depends on the diffusion of photocarriers excited by a modulated light. In this study, a novel hybrid fiber-optic illumination was developed to enhance the spatial resolution. It consists of a modulated light probe to generate a photocurrent signal and a ring of constant light, which suppresses the lateral diffusion of minority carriers excited by the modulated light. It is demonstrated that the spatial resolution was improved from 92 μm to 68 μm.},
  language  = {en}
}
@article{PoghossianBaeckerMayeretal.2015,
  author    = {Poghossian, Arshak and B{\"a}cker, Matthias and Mayer, Dirk and Sch{\"o}ning, Michael Josef},
  title     = {Gating capacitive field-effect sensors by the charge of nanoparticle/molecule hybrids},
  series = {Nanoscale},
  journal   = {Nanoscale},
  publisher = {Royal Society of Chemistry (RSC)},
  address   = {Cambridge},
  issn      = {2040-3372 (E-Journal); 2040-3364 (Print)},
  doi       = {10.1039/C4NR05987E},
  pages     = {1023 -- 1031},
  year      = {2015},
  language  = {en}
}
@article{AlmajhdiSengerAmeretal.2014,
  author    = {Almajhdi, Fahad N. and Senger, Tilo and Amer, Haitham M. and Gissmann, Lutz and {\"O}hlschl{\"a}ger, Peter},
  title     = {Design of a highly effective therapeutic HPV16 E6/E7-specific DNA vaccine: optimization by different ways of sequence rearrangements (Shuffling)},
  series = {PLOS one},
  volume    = {11},
  journal   = {PLOS one},
  number    = {9},
  publisher = {PLOS},
  address   = {San Francisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0113461},
  pages     = {e113461},
  year      = {2014},
  abstract  = {Persistent infection with the high-risk Human Papillomavirus type 16 (HPV 16) is the causative event for the development of cervical cancer and other malignant tumors of the anogenital tract and of the head and neck. Despite many attempts to develop therapeutic vaccines no candidate has entered late clinical trials. An interesting approach is a DNA based vaccine encompassing the nucleotide sequence of the E6 and E7 viral oncoproteins. Because both proteins are consistently expressed in HPV infected cells they represent excellent targets for immune therapy. Here we report the development of 8 DNA vaccine candidates consisting of differently rearranged HPV-16 E6 and E7 sequences within one molecule providing all naturally occurring epitopes but supposedly lacking transforming activity. The HPV sequences were fused to the J-domain and the SV40 enhancer in order to increase immune responses. We demonstrate that one out of the 8 vaccine candidates induces very strong cellular E6- and E7- specific cellular immune responses in mice and, as shown in regression experiments, efficiently controls growth of HPV 16 positive syngeneic tumors. This data demonstrates the potential of this vaccine candidate to control persistent HPV 16 infection that may lead to malignant disease. It also suggests that different sequence rearrangements influence the immunogenecity by an as yet unknown mechanism.},
  language  = {en}
}
@article{SchoeningPoghossian2006,
  author    = {Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {BioFEDs (field-effect devices) : State-of-the-art and new directions},
  series = {Electroanalysis},
  volume    = {18},
  journal   = {Electroanalysis},
  number    = {19-20},
  issn      = {1521-4109},
  doi       = {10.1002/elan.200603609},
  pages     = {1893 -- 1900},
  year      = {2006},
  language  = {en}
}
@article{WarmerWagnerSchoeningetal.2015,
  author    = {Warmer, Johannes and Wagner, Patrick and Sch{\"o}ning, Michael Josef and Kaul, Peter},
  title     = {Detection of triacetone triperoxide using temperature cycled metal-oxide semiconductor gas sensors},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431882},
  pages     = {1289 -- 1298},
  year      = {2015},
  language  = {en}
}
@article{DelleHuckBaeckeretal.2015,
  author    = {Delle, Lotta E. and Huck, Christina and B{\"a}cker, Matthias and M{\"u}ller, Frank and Grandthyll, Samuel and Jacobs, Karin and Lilischkis, Rainer and Vu, Xuan T. and Sch{\"o}ning, Michael Josef and Wagner, Patrick and Thoelen, Roland and Weil, Maryam and Ingebrandt, Sven},
  title     = {Impedimetric immunosensor for the detection of histamine based on reduced graphene oxide},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431863},
  pages     = {1327 -- 1334},
  year      = {2015},
  language  = {en}
}
@article{YoshinobuMoritzFingeretal.2006,
  author    = {Yoshinobu, Tatsuo and Moritz, Werner and Finger, Friedhelm and Sch{\"o}ning, Michael Josef},
  title     = {Application of thin-film amorphous silicon to chemical imaging},
  series = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  journal   = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  number    = {Paper 0910-A-20-01},
  editor    = {Comini, Elisabetta},
  isbn      = {9781558998711},
  pages     = {1 -- 10},
  year      = {2006},
  language  = {en}
}
@article{SchoeningAbouzarIngebrandtetal.2006,
  author    = {Sch{\"o}ning, Michael Josef and Abouzar, Maryam H. and Ingebrandt, Sven and Platen, Johannes and Offenh{\"a}usser, Andreas and Poghossian, Arshak},
  title     = {Towards label-free detection of charged macromolecules using field-effect-based structures : Scaling down from capacitive EIS sensor over ISFET to nano-scale devices},
  series = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  journal   = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  number    = {paper 0915-R05-04},
  editor    = {Comini, Elisabetta},
  isbn      = {9781558998711},
  pages     = {89 -- 94},
  year      = {2006},
  language  = {en}
}
@article{TakenagaSchneiderErbayetal.2015,
  author    = {Takenaga, Shoko and Schneider, Benno and Erbay, E. and Biselli, Manfred and Schnitzler, Thomas and Sch{\"o}ning, Michael Josef and Wagner, Torsten},
  title     = {Fabrication of biocompatible lab-on-chip devices for biomedical applications by means of a 3D-printing process},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201532053},
  pages     = {1347 -- 1352},
  year      = {2015},
  abstract  = {A new microfluidic assembly method for semiconductor-based biosensors using 3D-printing technologies was proposed for a rapid and cost-efficient design of new sensor systems. The microfluidic unit is designed and printed by a 3D-printer in just a few hours and assembled on a light-addressable potentiometric sensor (LAPS) chip using a photo resin. The cell growth curves obtained from culturing cells within microfluidics-based LAPS systems were compared with cell growth curves in cell culture flasks to examine biocompatibility of the 3D-printed chips. Furthermore, an optimal cell culturing within microfluidics-based LAPS chips was achieved by adjusting the fetal calf serum concentrations of the cell culture medium, an important factor for the cell proliferation.},
  language  = {en}
}
@article{MolinnusBaeckerIkenetal.2015,
  author    = {Molinnus, Denise and B{\"a}cker, Matthias and Iken, Heiko and Poghossian, Arshak and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Concept for a biomolecular logic chip with an integrated sensor and actuator function},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431913},
  pages     = {1382 -- 1388},
  year      = {2015},
  abstract  = {A concept for a new generation of an integrated multi-functional biosensor/actuator system is developed, which is based on biomolecular logic principles. Such a system is expected to be able to detect multiple biochemical input signals simultaneously and in real-time and convert them into electrical output signals with logical operations such as OR, AND, etc. The system can be designed as a closed-loop drug release device triggered by an enzyme logic gate, while the release of the drug induced by the actuator at the required dosage and timing will be controlled by an additional drug sensor. Thus, the system could help to make an accurate and specific diagnosis. The presented concept is exemplarily demonstrated by using an enzyme logic gate based on a glucose/glucose oxidase system, a temperature-responsive hydrogel mimicking the actuator function and an insulin (drug) sensor. In this work, the results of functional testing of individual amperometric glucose and insulin sensors as well as an impedimetric sensor for the detection of the hydrogel swelling/shrinking are presented.},
  language  = {en}
}
@article{HenkenOosterhuisOehlschlaegeretal.2012,
  author    = {Henken, F. E. and Oosterhuis, K. and {\"O}hlschl{\"a}ger, Peter and Bosch, L. and Hooijberg, E. and Haanen, J. B. A. G. and Steenbergen, R. D. M.},
  title     = {Preclinical safety evaluation of DNA vaccines encoding modified HPV16 E6 and E7},
  series = {Vaccine},
  volume    = {30},
  journal   = {Vaccine},
  number    = {28},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0264-410X},
  doi       = {10.1016/j.vaccine.2012.04.013},
  pages     = {4259 -- 4266},
  year      = {2012},
  abstract  = {Persistent infection with high-risk human papillomaviruses (hrHPV) can result in the formation of anogenital cancers. As hrHPV proteins E6 and E7 are required for cancer initiation and maintenance, they are ideal targets for immunotherapeutic interventions. Previously, we have described the development of DNA vaccines for the induction of HPV16 E6 and E7 specific T cell immunity. These vaccines consist of 'gene-shuffled' (SH) versions of HPV16 E6 and E7 that were fused to Tetanus Toxin Fragment C domain 1 (TTFC) and were named TTFC-E6SH and TTFC-E7SH. Gene-shuffling was performed to avoid the risk of inducing malignant transformation at the vaccination site. Here, we describe the preclinical safety evaluation of these candidate vaccines by analysis of their transforming capacity in vitro using established murine fibroblasts (NIH 3T3 cells) and primary human foreskin keratinocytes (HFKs). We demonstrate that neither ectopic expression of TTFC-E6SH and TTFC-E7SH alone or in combination enabled NIH 3T3 cells to form colonies in soft agar. In contrast, expression of HPV16 E6WT and E7WT alone or in combination resulted in effective transformation. Similarly, retroviral transduction of HFKs from three independent donors with both TTFC-E6SH and TTFC-E7SH alone or in combination did not show any signs of immortalization. In contrast, the combined expression of E6WT and E7WT induced immortalization in HFKs from all donors. Based on these results we consider it justified to proceed to clinical evaluation of DNA vaccines encoding TTFC-E6SH and TTFC-E7SH in patients with HPV16 associated (pre)malignancies.},
  language  = {en}
}
@article{ImmelGruetzkeSpaeteetal.2012,
  author    = {Immel, Timo and Gr{\"u}tzke, Martin and Sp{\"a}te, Anne-Katrin and Groth, Ulrich and {\"O}hlschl{\"a}ger, Peter and Huhn, Thomas},
  title     = {Synthesis and X-ray structure analysis of a heptacoordinate titanium(IV)-bis-chelate with enhanced in vivo antitumor efficacy},
  series = {Chemical Communications},
  volume    = {48},
  journal   = {Chemical Communications},
  number    = {46},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {1364-548X},
  doi       = {10.1039/C2CC31624B},
  pages     = {5790 -- 5792},
  year      = {2012},
  abstract  = {Chelate stabilization of a titanium(IV)-salan alkoxide by ligand exchange with 2,6-pyridinedicarboxylic acid (dipic) resulted in heptacoordinate complex 3 which is not redox-active, stable on silica gel and has increased aqueous stability. 3 is highly toxic in HeLa S3 and Hep G2 and has enhanced antitumor efficacy in a mouse cervical-cancer model.},
  language  = {en}
}