@article{RauschKahmannBaltschunetal.2020,
  author    = {Rausch, Valentin and Kahmann, Stephanie Lucina and Baltschun, Christoph and Staat, Manfred and M{\"u}ller, Lars-Peter and Wegmann, Kilian},
  title     = {Pressure distribution to the distal biceps tendon at the radial tuberosity: a biomechanical study},
  series = {The Journal of Hand Surgery},
  volume    = {45},
  journal   = {The Journal of Hand Surgery},
  number    = {8},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0363-5023},
  doi       = {10.1016/j.jhsa.2020.01.006},
  pages     = {776.e1 -- 776.e9},
  year      = {2020},
  abstract  = {Purpose Mechanical impingement at the narrow radioulnar space of the tuberosity is believed to be an etiological factor in the injury of the distal biceps tendon. The aim of the study was to compare the pressure distribution at the proximal radioulnar space between 2 fixation techniques and the intact state. Methods Six right arms and 6 left arms from 5 female and 6 male frozen specimens were used for this study. A pressure transducer was introduced at the height of the radial tuberosity with the intact distal biceps tendon and after 2 fixation methods: the suture-anchor and the cortical button technique. The force (N), maximum pressure (kPa) applied to the radial tuberosity, and the contact area (mm²) of the radial tuberosity with the ulna were measured and differences from the intact tendon were detected from 60° supination to 60° pronation in 15° increments with the elbow in full extension and in 45° and 90° flexion of the elbow. Results With the distal biceps tendon intact, the pressures during pronation were similar regardless of extension and flexion and were the highest at 60° pronation with 90° elbow flexion (23.3 ± 53.5 kPa). After repair of the tendon, the mean peak pressure, contact area, and total force showed an increase regardless of the fixation technique. Highest peak pressures were found using the cortical button technique at 45° flexion of the elbow and 60° pronation. These differences were significantly different from the intact tendon. The contact area was significantly larger in full extension and 15°, 30°, and 60° pronation using the cortical button technique. Conclusions Pressures on the distal biceps tendon at the radial tuberosity increase during pronation, especially after repair of the tendon. Clinical relevance Mechanical impingement could play a role in both the etiology of primary distal biceps tendon ruptures and the complications occurring after fixation of the tendon using certain techniques.},
  language  = {en}
}
@article{HacklKahmannWegmannetal.2016,
  author    = {Hackl, Michael and Kahmann, Stephanie Lucina and Wegmann, Kilian and Ries, Christian and Staat, Manfred and M{\"u}ller, Lars-Peter},
  title     = {Shortening osteotomy of the proximal radius — a treatment option for isolated osteoarthritis of the lateral column of the elbow joint?},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4080-7},
  pages     = {128 -- 129},
  year      = {2016},
  abstract  = {Treatment of posttraumatic osteoarthritis of the radial column of the elbow joint remains a challenging yet common issue. While partial joint replacement leads to high revision rates, radial head excision has shown to severely increase joint instability. Shortening osteotomy of the radius could be an option to decrease the contact pressure of the radiohumeral joint and thereby pain levels without causing valgus instability. Hence, the aim of this biomechanical study was to evaluate the effects of radial shortening on axial load distribution and valgus stability of the elbow joint.},
  language  = {en}
}
@article{WegmannHacklStaatetal.2016,
  author    = {Wegmann, Kilian and Hackl, Michael and Staat, Manfred and Mayer, Katharina and M{\"u}ller, Lars-Peter},
  title     = {Double plate osteosynthesis of proximal ulna fractures: biomechanical and clinical results},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4079-0},
  pages     = {58 -- 59},
  year      = {2016},
  abstract  = {While plate fixation of proximal ulna fractures might lead to superior clinical results compared to tension band wiring, regular plates represent an established risk factor for wound complications. The olecranon double plates (Medartis, Basel, CH) might decrease complications related to the osteosynthesis because of their low profile and better anatomical fit. This study aimed to evaluate the biomechanical performance and clinical results of the olecranon double plates.},
  language  = {en}
}
@article{HacklLeschingerStaatetal.2016,
  author    = {Hackl, Michael and Leschinger, T. and Staat, Manfred and M{\"u}ller, Lars-Peter and Wegmann, Kilian},
  title     = {Reconstruction of the interosseous membrane in the Essex Lopresti lesion — a biomechanical evaluation},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4080-7},
  pages     = {130 -- 131},
  year      = {2016},
  abstract  = {Surgical reconstruction of the interosseous membrane (IOM) could restore longitudinal forearm stability to avoid persisting disability due to capituloradial and ulnocarpal impingement in Essex Lopresti lesions. This biomechanical study aimed to assess longitudinal forearm stability of intact specimens, after sectioning of the IOM and after reconstruction with a TightRope construct using either a single or double bundle technique.},
  language  = {en}
}
@article{HacklAndermahrStaatetal.2017,
  author    = {Hackl, Michael and Andermahr, J. and Staat, Manfred and Bremer, I. and Borggrefe, J. and Prescher, A. and M{\"u}ller, Lars-Peter and Wegmann, Kilian},
  title     = {Suture button reconstruction of the central band of the interosseous membrane in Essex-Lopresti lesions: a comparative biomechanical investigation},
  series = {The Journal of Hand Surgery (European Volume)},
  volume    = {42},
  journal   = {The Journal of Hand Surgery (European Volume)},
  number    = {4},
  publisher = {Sage},
  address   = {London},
  issn      = {2043-6289 (Online)},
  doi       = {10.1177/1753193416665943},
  pages     = {370 -- 376},
  year      = {2017},
  language  = {en}
}
@article{LeschingerBirgelHackletal.2019,
  author    = {Leschinger, Tim and Birgel, Stefan and Hackl, Michael and Staat, Manfred and M{\"u}ller, Lars-Peter and Wegmann, Kilian},
  title     = {A musculoskeletal shoulder simulation of moment arms and joint reaction forces after medialization of the supraspinatus footprint in rotator cuff repair},
  series = {Computer Methods in Biomechanics and Biomedical Engineering},
  journal   = {Computer Methods in Biomechanics and Biomedical Engineering},
  number    = {Early view},
  publisher = {Taylor \& Francis},
  address   = {London},
  doi       = {10.1080/10255842.2019.1572749},
  year      = {2019},
  language  = {en}
}
@article{LeschingerBeschAydinetal.2019,
  author    = {Leschinger, Tim and Besch, Katharina and Aydin, Cansu and Staat, Manfred and Scaal, Martin and M{\"u}ller, Lars-Peter and Wegmann, Kilian},
  title     = {Irreparable rotator cuff tears: a biomechanical comparison of superior capsuloligamentous complex reconstruction techniques and an interposition graft technique},
  series = {The Orthopaedic Journal of Sports Medicine},
  volume    = {7},
  journal   = {The Orthopaedic Journal of Sports Medicine},
  number    = {8},
  doi       = {10.1177/2325967119864590},
  pages     = {1 -- 5},
  year      = {2019},
  language  = {en}
}
@article{BabilonWilbringTappertetal.2018,
  author    = {Babilon, Katharina and Wilbring, Daniela and Tappert, Tim and Pfaff, Raphael and Enning, Manfred},
  title     = {Schienenfahrzeugtechnik hands on - FH Aachen IMechE Railway Challenge},
  series = {Ingenieurspiegel},
  journal   = {Ingenieurspiegel},
  number    = {2},
  publisher = {Public Verlag},
  address   = {Bingen},
  issn      = {1868-5919},
  pages     = {20 -- 22},
  year      = {2018},
  language  = {de}
}
@article{PfaffEnningSutter2022,
  author    = {Pfaff, Raphael and Enning, Manfred and Sutter, Stefan},
  title     = {A risk‑based approach to automatic brake tests for rail freight service: incident analysis and realisation concept},
  series = {SN Applied Sciences},
  volume    = {4},
  journal   = {SN Applied Sciences},
  number    = {4},
  publisher = {Springer},
  address   = {Cham},
  issn      = {2523-3971},
  doi       = {10.1007/s42452-022-05007-x},
  pages     = {1 -- 14},
  year      = {2022},
  abstract  = {This study reviews the practice of brake tests in freight railways, which is time consuming and not suitable to detect certain failure types. Public incident reports are analysed to derive a reasonable brake test hardware and communication architecture, which aims to provide automatic brake tests at lower cost than current solutions. The proposed solutions relies exclusively on brake pipe and brake cylinder pressure sensors, a brake release position switch as well as radio communication via standard protocols. The approach is embedded in the Wagon 4.0 concept, which is a holistic approach to a smart freight wagon. The reduction of manual processes yields a strong incentive due to high savings in manual labour and increased productivity.},
  language  = {en}
}
@article{SchmidtEnningPfaff2018,
  author    = {Schmidt, Bernd and Enning, Manfred and Pfaff, Raphael},
  title     = {G{\"u}terwagen 4.0 - Der G{\"u}terwagen f{\"u}r das Internet der Dinge Teil 3: Einf{\"u}hrungsszenarien f{\"u}r aktive, kommunikative G{\"u}terwagen},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {67},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {60 -- 64},
  year      = {2018},
  abstract  = {Wenn durch innovative, automatisierte G{\"u}terwagen betriebswirtschaftliche Vorteile nutzbar gemacht werden sollen, muss die Migration auf das neue System in sinnvollen Teilschritten unter Ber{\"u}cksichtigung der organisationellen und betrieblichen Vereinbarkeit vorgenommen werden. Eine stufenweise Migration mit Nachr{\"u}stbarkeit und Kompatibilit{\"a}t kann die optimale Ausstattungsvariante f{\"u}r die unterschiedlichen Betriebsszenarien sowie eine Steigerung der Wirtschaftlichkeit des Gesamtsystems bieten.},
  language  = {de}
}
@article{PfaffBabilon2023,
  author    = {Pfaff, Raphael and Babilon, Katharina},
  title     = {Railway Challenge - moderne Auflage der Rainhill Trials?},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {2023},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {4},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {55 -- 58},
  year      = {2023},
  abstract  = {Die IMechE Railway Challenge wird j{\"a}hrlich in Stapleford, Großbritannien ausgetragen. Im Rahmen der Challenge entwickeln und bauen Studierende eine Lokomotive und vergleichen sich in verschiedenen Disziplinen, darunter eine automatisierte Zielbremsung, optimale Energier{\"u}ckgewinnung beim Bremsen und minimale Ger{\"a}uschemissionen. Neben diesen und weiteren technischen Wettbewerbsdisziplinen treten die Fahrzeuge und die Teams auch in nicht-technischen Disziplinen wie einer Business Case Challenge an.},
  language  = {de}
}
@article{PfaffGidaszewskiSchmidt2020,
  author    = {Pfaff, Raphael and Gidaszewski, Lars and Schmidt, Bernd},
  title     = {Ber{\"u}cksichtigung von No Fault Found im Diagnose- und Instandhaltungssystem von Schienenfahrzeugen},
  series = {ETR - Eisenbahntechnische Rundschau},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {56 -- 59},
  year      = {2020},
  abstract  = {Intermittierende und nicht reproduzierbare Fehler, auch als No Fault Found bezeichnet, treten in praktisch allen Bereichen auf und sorgen f{\"u}r hohe Kosten. Diese sind h{\"a}ufig auf unpr{\"a}zise Fehlerbeschreibungen zur{\"u}ckzuf{\"u}hren. Im vorliegenden Beitrag werden Anpassungen der Vorgehensweise bei der Entwicklung und Anpassungen des Diagnosesystems vorgeschlagen.},
  language  = {de}
}
@article{SchollPalmLehmannetal.1998,
  author    = {Scholl, Ingrid and Palm, Christoph and Lehmann, Thomas Martin and Spitzer, Klaus},
  title     = {Quantitative Farbmessung in laryngoskopischen Bildern. Palm, C; Scholl, I; Lehmann, TM; Spitzer, K.},
  series = {Bildverarbeitung f{\"u}r die Medizin 1998. Hrsg.: Thomas Lehmann ...},
  journal   = {Bildverarbeitung f{\"u}r die Medizin 1998. Hrsg.: Thomas Lehmann ...},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {3-540-63885-7},
  pages     = {412 -- 416},
  year      = {1998},
  language  = {en}
}
@article{FiedlerLaddBitz2017,
  author    = {Fiedler, Thomas M. and Ladd, Mark E. and Bitz, Andreas},
  title     = {RF safety assessment of a bilateral four-channel transmit/receive 7 Tesla breast coil: SAR versus temperature limits},
  series = {Medical Physics},
  volume    = {44},
  journal   = {Medical Physics},
  number    = {1},
  doi       = {10.1002/mp.12034},
  pages     = {143 -- 157},
  year      = {2017},
  language  = {en}
}
@article{FiedlerLaddClemensetal.2020,
  author    = {Fiedler, Thomas M. and Ladd, Mark E. and Clemens, Markus and Bitz, Andreas},
  title     = {Safety of subjects during radiofrequency exposure in ultra-high-field magnetic resonance imaging},
  series = {IEEE Letters on Electromagnetic Compatibility Practice and Applications},
  volume    = {2},
  journal   = {IEEE Letters on Electromagnetic Compatibility Practice and Applications},
  number    = {3},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {2637-6423},
  doi       = {10.1109/LEMCPA.2020.3029747},
  pages     = {1 -- 8},
  year      = {2020},
  abstract  = {Magnetic resonance imaging (MRI) is one of the most important medical imaging techniques. Since the introduction of MRI in the mid-1980s, there has been a continuous trend toward higher static magnetic fields to obtain i.a. a higher signal-to-noise ratio. The step toward ultra-high-field (UHF) MRI at 7 Tesla and higher, however, creates several challenges regarding the homogeneity of the spin excitation RF transmit field and the RF exposure of the subject. In UHF MRI systems, the wavelength of the RF field is in the range of the diameter of the human body, which can result in inhomogeneous spin excitation and local SAR hotspots. To optimize the homogeneity in a region of interest, UHF MRI systems use parallel transmit systems with multiple transmit antennas and time-dependent modulation of the RF signal in the individual transmit channels. Furthermore, SAR increases with increasing field strength, while the SAR limits remain unchanged. Two different approaches to generate the RF transmit field in UHF systems using antenna arrays close and remote to the body are investigated in this letter. Achievable imaging performance is evaluated compared to typical clinical RF transmit systems at lower field strength. The evaluation has been performed under consideration of RF exposure based on local SAR and tissue temperature. Furthermore, results for thermal dose as an alternative RF exposure metric are presented.},
  language  = {en}
}
@article{BlomeMashhoon1984,
  author    = {Blome, Hans-Joachim and Mashhoon, Bahram},
  title     = {Quasi-normal oscillations of a Schwarzschild black hole},
  series = {Physics Letters A. 100 (1984), H. 5},
  journal   = {Physics Letters A. 100 (1984), H. 5},
  isbn      = {0375-9601},
  pages     = {231 -- 234},
  year      = {1984},
  language  = {en}
}
@article{VoegeleJosyabhatlaBalletal.2023,
  author    = {V{\"o}gele, Stefan and Josyabhatla, Vishnu Teja and Ball, Christopher Stephen and Rhoden, Imke and Grajewski, Matthias and R{\"u}bbelke, Dirk and Kuckshinrichs, Wilhelm},
  title     = {Robust assessment of energy scenarios from stakeholders' perspectives},
  series = {Energy},
  journal   = {Energy},
  number    = {In Press, Article 128326},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-6785 (Online)},
  doi       = {10.1016/j.energy.2023.128326},
  year      = {2023},
  abstract  = {Using scenarios is vital in identifying and specifying measures for successfully transforming the energy system. Such transformations can be particularly challenging and require the support of a broader set of stakeholders. Otherwise, there will be opposition in the form of reluctance to adopt the necessary technologies. Usually, processes for considering stakeholders' perspectives are very time-consuming and costly. In particular, there are uncertainties about how to deal with modifications in the scenarios. In principle, new consulting processes will be required. In our study, we show how multi-criteria decision analysis can be used to analyze stakeholders' attitudes toward transition paths. Since stakeholders differ regarding their preferences and time horizons, we employ a multi-criteria decision analysis approach to identify which stakeholders will support or oppose a transition path. We provide a flexible template for analyzing stakeholder preferences toward transition paths. This flexibility comes from the fact that our multi-criteria decision aid-based approach does not involve intensive empirical work with stakeholders. Instead, it involves subjecting assumptions to robustness analysis, which can help identify options to influence stakeholders' attitudes toward transitions.},
  language  = {en}
}
@article{GoettscheHoffschmidtSchmitzetal.2010,
  author    = {G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Schmitz, Stefan and Sauerborn, Markus},
  title     = {Solar Concentrating Systems Using Small Mirror Arrays},
  series = {Journal of solar energy engineering},
  volume    = {132},
  journal   = {Journal of solar energy engineering},
  number    = {1},
  publisher = {ASME},
  address   = {New York},
  issn      = {0199-6231},
  doi       = {10.1115/1.4000332},
  pages     = {4 Seiten},
  year      = {2010},
  abstract  = {The cost of solar tower power plants is dominated by the heliostat field making up roughly 50\% of investment costs. Classical heliostat design is dominated by mirrors brought into position by steel structures and drives that guarantee high accuracies under wind loads and thermal stress situations. A large fraction of costs is caused by the stiffness requirements of the steel structure, typically resulting in ~ 20 kg/m² steel per mirror area. The typical cost figure of heliostats (figure mentioned by Solucar at Solar Paces Conference, Seville, 2006) is currently in the area of 150 €/m² caused by the increasing price of the necessary raw materials. An interesting option to reduce costs lies in a heliostat design where all moving parts are protected from wind loads. In this way, drives and mechanical layout may be kept less robust, thereby reducing material input and costs. In order to keep the heliostat at an appropriate size, small mirrors (around 10x10 cm²) have to be used, which are placed in a box with a transparent cover. Innovative drive systems are developed in order to obtain a cost-effective design. A 0,5x0,5 m² demonstration unit will be constructed. Tests of the unit are carried out with a high-precision artificial sun unit that imitates the sun's path with an accuracy of less than 0.5 mrad and creates a beam of parallel light with a divergence of less than 4 mrad.},
  language  = {en}
}
@article{BallVoegeleGrajewskietal.2021,
  author    = {Ball, Christopher Stephen and V{\"o}gele, Stefan and Grajewski, Matthias and Kuckshinrichs, Wilhelm},
  title     = {E-mobility from a multi-actor point of view: Uncertainties and their impacts},
  series = {Technological Forecasting and Social Change},
  volume    = {170},
  journal   = {Technological Forecasting and Social Change},
  number    = {Art. 120925},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0040-1625},
  doi       = {10.1016/j.techfore.2021.120925},
  year      = {2021},
  language  = {en}
}
@article{WeberArentMuenchetal.2016,
  author    = {Weber, Tobias and Arent, Jan-Christoph and M{\"u}nch, Lukas and Duhovic, Miro and Balvers, Johannes Mattheus},
  title     = {A fast method for the generation of boundary conditions for thermal autoclave simulation},
  series = {Composites Part A},
  volume    = {88},
  journal   = {Composites Part A},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-835X},
  doi       = {10.1016/j.compositesa.2016.05.036},
  pages     = {216 -- 225},
  year      = {2016},
  abstract  = {Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.},
  language  = {en}
}