@article{OlaruKowalskiSethietal.2012,
  author    = {Olaru, Alexandra Maria and Kowalski, Julia and Sethi, Vaishali and Bl{\"u}mich, Bernhard},
  title     = {Exchange relaxometry of flow at small P{\´e}clet numbers in a glass bead pack},
  series = {Journal of Magnetic Resonance (JMR)},
  volume    = {220},
  journal   = {Journal of Magnetic Resonance (JMR)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1096-0856},
  doi       = {10.1016/j.jmr.2012.04.015},
  pages     = {32 -- 44},
  year      = {2012},
  abstract  = {In this paper we consider low P{\´e}clet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.},
  language  = {en}
}
@article{FischerKowalskiPudasaini2012,
  author    = {Fischer, Jan-Thomas and Kowalski, Julia and Pudasaini, Shiva P.},
  title     = {Topographic curvature effects in applied avalanche modelling},
  series = {Cold Regions Science and Technology},
  volume    = {74-75},
  journal   = {Cold Regions Science and Technology},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-7441},
  doi       = {10.1016/j.coldregions.2012.01.005},
  pages     = {21 -- 30},
  year      = {2012},
  abstract  = {This paper describes the implementation of topographic curvature effects within the RApid Mass MovementS (RAMMS) snow avalanche simulation toolbox. RAMMS is based on a model similar to shallow water equations with a Coulomb friction relation and the velocity dependent Voellmy drag. It is used for snow avalanche risk assessment in Switzerland. The snow avalanche simulation relies on back calculation of observed avalanches. The calibration of the friction parameters depends on characteristics of the avalanche track. The topographic curvature terms are not yet included in the above mentioned classical model. Here, we fundamentally improve this model by mathematically and physically including the topographic curvature effects. By decomposing the velocity dependent friction into a topography dependent term that accounts for a curvature enhancement in the Coulomb friction, and a topography independent contribution similar to the classical Voellmy drag, we construct a general curvature dependent frictional resistance, and thus propose new extended model equations. With three site-specific examples, we compare the apparent frictional resistance of the new approach, which includes topographic curvature effects, to the classical one. Our simulation results demonstrate substantial effects of the curvature on the flow dynamics e.g., the dynamic pressure distribution along the slope. The comparison of resistance coefficients between the two models demonstrates that the physically based extension presents an improvement to the classical approach. Furthermore a practical example highlights its influence on the pressure outline in the run out zone of the avalanche. Snow avalanche dynamics modeling natural terrain curvature centrifugal force friction coefficients.},
  language  = {en}
}
@article{BuehlerChristenKowalskietal.2011,
  author    = {B{\"u}hler, Yves and Christen, Marc and Kowalski, Julia and Bartelt, Perry},
  title     = {Sensitivity of snow avalanche simulations to digital elevation model quality and resolution},
  series = {Annals of Glaciology},
  volume    = {52},
  journal   = {Annals of Glaciology},
  number    = {58},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  isbn      = {1727-5644},
  pages     = {72 -- 80},
  year      = {2011},
  abstract  = {Digital elevation models (DEMs), represent the three-dimensional terrain and are the basic input for numerical snow avalanche dynamics simulations. DEMs can be acquired using topographic maps or remote-sensing technologies, such as photogrammetry or lidar. Depending on the acquisition technique, different spatial resolutions and qualities are achieved. However, there is a lack of studies that investigate the sensitivity of snow avalanche simulation algorithms to the quality and resolution of DEMs. Here, we perform calculations using the numerical avalance dynamics model RAMMS, varying the quality and spatial resolution of the underlying DEMs, while holding the simulation parameters constant. We study both channelized and open-terrain avalanche tracks with variable roughness. To quantify the variance of these simulations, we use well-documented large-scale avalanche events from Davos, Switzerland (winter 2007/08), and from our large-scale avalanche test site, Valĺee de la Sionne (winter 2005/06). We find that the DEM resolution and quality is critical for modeled flow paths, run-out distances, deposits, velocities and impact pressures. Although a spatial resolution of ~25 m is sufficient for large-scale avalanche modeling, the DEM datasets must be checked carefully for anomalies and artifacts before using them for dynamics calculations.},
  language  = {en}
}
@article{DachwaldSchmidtSeboldtetal.2003,
  author    = {Dachwald, Bernd and Schmidt, Tanja D. and Seboldt, Wolfgang and Auweter-Kurtz,},
  title     = {Flight Opportunities from Mars to Earth for Piloted Missions Using Continuous Thrust Propulsion / Schmidt, Tanja D. ; Dachwald, Bernd ; Seboldt, Wolfgang ; Auweter-Kurtz, Monika},
  publisher = {-},
  pages     = {1 -- 9},
  year      = {2003},
  language  = {en}
}
@article{Kowalski2008,
  author    = {Kowalski, Julia},
  title     = {Mathematische Murgangmodellierung},
  series = {Newsletter Naturgefahren},
  volume    = {2008},
  journal   = {Newsletter Naturgefahren},
  number    = {2},
  organization    = {Eidgen{\"o}ssisches Institut f{\"u}r Schnee-und Lawinenforschung SLF},
  pages     = {4 -- 5},
  year      = {2008},
  language  = {de}
}
@article{SaffeLodewiksHaasetal.1989,
  author    = {Saffe, P. and Lodewiks, J. and Haas, H.-J. and Feigel, H.-J. and Ulrich, H. and Mauer, J. and Ortwig, H. and Dahmann, Peter and Rotth{\"a}user, S. and Tao, J. and Ohlischl{\"a}ger, O. and Scholz, D. and Bergmann, M. and Anders, P.},
  title     = {Neues von ASB Antreiben - Steuern - Bewegen},
  series = {{\"O}lhydraulik und Pneumatik. Vol. 33 (1989), H. 7},
  journal   = {{\"O}lhydraulik und Pneumatik. Vol. 33 (1989), H. 7},
  issn      = {0341-2660},
  pages     = {550 -- 572},
  year      = {1989},
  language  = {de}
}
@article{HennPolaczek2007,
  author    = {Henn, Gudrun and Polaczek, Christa},
  title     = {Studienerfolg in den Ingenieurwissenschaften},
  series = {Das Hochschulwesen : HSW ; Forum f{\"u}r Hochschulforschung, -praxis und -politik},
  volume    = {55},
  journal   = {Das Hochschulwesen : HSW ; Forum f{\"u}r Hochschulforschung, -praxis und -politik},
  number    = {5},
  issn      = {0018-2974},
  pages     = {144 -- 147},
  year      = {2007},
  language  = {de}
}
@article{PolaczekHenn2008,
  author    = {Polaczek, Christa and Henn, Gudrun},
  title     = {Gute Vorkenntnisse verk{\"u}rzen die Studienzeit},
  series = {Mathematikinformation : eine Zeitschrift von Begabtenf{\"o}rderung Mathematik e.V.},
  volume    = {2008},
  journal   = {Mathematikinformation : eine Zeitschrift von Begabtenf{\"o}rderung Mathematik e.V.},
  number    = {49},
  publisher = {Begabtenf{\"o}rderung Mathematik},
  address   = {Neubiberg},
  issn      = {1612-9156},
  pages     = {46 -- 50},
  year      = {2008},
  language  = {de}
}
@article{GenzKingWahle1992,
  author    = {Genz, M. and King, H. and Wahle, Michael},
  title     = {Mikrozellige Polyurethan-Elastomere als Federelement in Automobilanwendungen},
  series = {Automobiltechnische Zeitschrift ; ATZ},
  volume    = {94},
  journal   = {Automobiltechnische Zeitschrift ; ATZ},
  number    = {10},
  issn      = {0001-2785},
  pages     = {512 -- 520},
  year      = {1992},
  language  = {de}
}
@article{KraemerDaabMuelleretal.2013,
  author    = {Kr{\"a}mer, Stefan and Daab, Dominique Jonas and M{\"u}ller, Brigitte and Wagner, Tobias and Baader, Fabian and Hessel, Joana and Gdalewitsch, Georg and Plescher, Engelbert and Dachwald, Bernd and Wahle, Michael and Gierse, Andreas and Vetter, Rudolf and Pf{\"u}tzenreuter, Lysan},
  title     = {Development and flight-testing of a system to isolate vibrations for microgravity experiments on sounding rockets},
  series = {21st ESA Symposium on Rocket and Balloon Research},
  journal   = {21st ESA Symposium on Rocket and Balloon Research},
  pages     = {1 -- 8},
  year      = {2013},
  language  = {en}
}
@article{FunkeDickhoffKeinzetal.2014,
  author    = {Funke, Harald and Dickhoff, J. and Keinz, Jan and Anis, H. A. and Parente, A. and Hendrick, P.},
  title     = {Experimental and numerical study of the micromix combustion principle applied for hydrogen and hydrogen-rich syngas as fuel with increased energy density for industrial gas turbine applications},
  series = {Energy procedia},
  journal   = {Energy procedia},
  number    = {61},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102 (E-Journal)},
  doi       = {10.1016/j.egypro.2014.12.201},
  pages     = {1736 -- 1739},
  year      = {2014},
  abstract  = {The Dry Low NOx (DLN) Micromix combustion principle with increased energy density is adapted for the industrial gas turbine APU GTCP 36-300 using hydrogen and hydrogen-rich syngas with a composition of 90\%-Vol. hydrogen (H₂) and 10\%-Vol. carbon-monoxide (CO). Experimental and numerical studies of several combustor geometries for hydrogen and syngas show the successful advance of the DLN Micromix combustion from pure hydrogen to hydrogen-rich syngas. The impact of the different fuel properties on the combustion principle and aerodynamic flame stabilization design laws, flow field, flame structure and emission characteristics is investigated by numerical analysis using a hybrid Eddy Break Up combustion model and validated against experimental results.},
  language  = {en}
}
@article{PeekenRosenkranzSchelenz1991,
  author    = {Peeken, Heinz and Rosenkranz, Josef and Schelenz, R.},
  title     = {Ber{\"u}cksichtigung des Einflusses der Gleitlagergeh{\"a}usesteifigkeit auf das dynamische Verhalten von Rotoren},
  series = {Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.},
  volume    = {30},
  journal   = {Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.},
  number    = {9},
  issn      = {0341-2652},
  pages     = {71 -- 75},
  year      = {1991},
  language  = {de}
}
@article{SchirraWatmuffBauschat2014,
  author    = {Schirra, Julian and Watmuff, Jonathan and Bauschat, J.-Michael},
  title     = {Highly non-planar lifting systems: a relative assessment of existing potential-methodologies to accurately estimate the induced drag},
  series = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.},
  journal   = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.},
  organization    = {American Institute of Aeronautics and Astronautics},
  isbn      = {978-1-62410-288-2},
  doi       = {10.2514/6.2014-2988},
  pages     = {Publ. online},
  year      = {2014},
  language  = {en}
}
@article{StadlerGarveyEmbsetal.2014,
  author    = {Stadler, Alexander Maximilian and Garvey, Christopher J. and Embs, Jan Peter and Koza, Michael Marek and Unruh, Tobias and Artmann, Gerhard and Zaccai, Guiseppe},
  title     = {Picosecond dynamics in haemoglobin from different species: A quasielastic neutron scattering study},
  series = {Biochimica et biophysica acta (BBA): General Subjects},
  volume    = {1840},
  journal   = {Biochimica et biophysica acta (BBA): General Subjects},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-8006 (E-Journal); 0304-4165 (Print)},
  doi       = {10.1016/j.bbagen.2014.06.007},
  pages     = {2989 -- 2999},
  year      = {2014},
  language  = {en}
}
@article{KonstantinidisFloresMartinezDachwaldetal.2015,
  author    = {Konstantinidis, Konstantinos and Flores Martinez, Claudio and Dachwald, Bernd and Ohndorf, Andreas and Dykta, Paul and Bowitz, Pascal and Rudolph, Martin and Digel, Ilya and Kowalski, Julia and Voigt, Konstantin and F{\"o}rstner, Roger},
  title     = {A lander mission to probe subglacial water on Saturn's moon enceladus for life},
  series = {Acta astronautica},
  volume    = {Vol. 106},
  journal   = {Acta astronautica},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2030 (E-Journal); 0094-5765 (Print)},
  pages     = {63 -- 89},
  year      = {2015},
  language  = {en}
}
@article{DachwaldMikuckiTulaczyketal.2014,
  author    = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng},
  title     = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems},
  series = {Annals of Glaciology},
  volume    = {55},
  journal   = {Annals of Glaciology},
  number    = {65},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  issn      = {1727-5644},
  doi       = {10.3189/2014AoG65A004},
  pages     = {14 -- 22},
  year      = {2014},
  abstract  = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.},
  language  = {en}
}
@article{MathiakPlescherWillnecker2005,
  author    = {Mathiak, Gerhard and Plescher, Engelbert and Willnecker, Rainer},
  title     = {Liquid metal diffusion experiments in microgravity - Vibrational effects},
  series = {Measurement science and technology},
  volume    = {Vol. 16},
  journal   = {Measurement science and technology},
  number    = {No. 2},
  issn      = {0957-0233},
  doi       = {10.1088/0957-0233/16/2/003},
  pages     = {336},
  year      = {2005},
  language  = {en}
}
@article{MathiakWillneckerPlescher2005,
  author    = {Mathiak, Gerhard and Willnecker, Rainer and Plescher, Engelbert},
  title     = {Vibrational effects on diffusion experiments},
  series = {Microgravity science and technology : international journal for microgravity research and applications},
  volume    = {Vol. 15},
  journal   = {Microgravity science and technology : international journal for microgravity research and applications},
  number    = {No. 1},
  issn      = {0938-0108},
  pages     = {295 -- 300},
  year      = {2005},
  language  = {en}
}
@article{SeifarthGossmannGrosseetal.2015,
  author    = {Seifarth, Volker and Goßmann, Matthias and Grosse, J. O. and Becker, C. and Heschel, I. and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Development of a Bioreactor to Culture Tissue Engineered Ureters Based on the Application of Tubular OPTIMAIX 3D Scaffolds},
  series = {Urologia Internationalis},
  volume    = {2015},
  journal   = {Urologia Internationalis},
  number    = {95},
  publisher = {Karger},
  address   = {Basel},
  issn      = {0042-1138},
  doi       = {10.1159/000368419},
  pages     = {106 -- 113},
  year      = {2015},
  language  = {en}
}
@article{HajAyedKustererFunkeetal.2015,
  author    = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.},
  title     = {Experimental and numerical investigations of the dry-low-NOx hydrogen micromix combustion chamber of an industrial gas turbine},
  series = {Propulsion and power research},
  volume    = {Vol. 4},
  journal   = {Propulsion and power research},
  number    = {Iss. 3},
  issn      = {2212-540X},
  doi       = {10.1016/j.jppr.2015.07.005},
  pages     = {123 -- 131},
  year      = {2015},
  language  = {en}
}