@inproceedings{PirovanoSeefeldtDachwaldetal.2015,
  author    = {Pirovano, Laura and Seefeldt, Patric and Dachwald, Bernd and Noomen, Ron},
  title     = {Attitude and orbital modeling of an uncontrolled solar-sail experiment in low-Earth orbit},
  series = {25th International Symposium on Space Flight Dynamics ISSFD},
  booktitle = {25th International Symposium on Space Flight Dynamics ISSFD},
  pages     = {1 -- 15},
  year      = {2015},
  abstract  = {Gossamer-1 is the first project of the three-step Gossamer roadmap, the purpose of which is to develop, prove and demonstrate that solar-sail technology is a safe and reliable propulsion technique for long-lasting and high-energy missions. This paper firstly presents the structural analysis performed on the sail to understand its elastic behavior. The results are then used in attitude and orbital simulations. The model considers the main forces and torques that a satellite experiences in low-Earth orbit coupled with the sail deformation. Doing the simulations for varying initial conditions in attitude and rotation rate, the results show initial states to avoid and maximum rotation rates reached for correct and faulty deployment of the sail. Lastly comparisons with the classic flat sail model are carried out to test the hypothesis that the elastic behavior does play a role in the attitude and orbital behavior of the sail},
  language  = {en}
}
@inproceedings{DachwaldKahleWie2006,
  author    = {Dachwald, Bernd and Kahle, Ralph and Wie, Bong},
  title     = {Solar sail Kinetic Energy Impactor (KEI) mission design tradeoffs for impacting and deflecting asteroid 99942 Apophis},
  series = {AIAA/AAS Astrodynamics Specialist Conference and Exhibit},
  booktitle = {AIAA/AAS Astrodynamics Specialist Conference and Exhibit},
  doi       = {10.2514/6.2006-6178},
  pages     = {1 -- 20},
  year      = {2006},
  abstract  = {Near-Earth asteroid 99942 Apophis provides a typical example for the evolution of asteroid orbits that lead to Earth-impacts after a close Earth-encounter that results in a resonant return. Apophis will have a close Earth-encounter in 2029 with potential very close subsequent Earth-encounters (or even an impact) in 2036 or later, depending on whether it passes through one of several so-called gravitational keyholes during its 2029-encounter. Several pre-2029-deflection scenarios to prevent Apophis from doing this have been investigated so far. Because the keyholes are less than 1 km in size, a pre-2029 kinetic impact is clearly the best option because it requires only a small change in Apophis' orbit to nudge it out of a keyhole. A single solar sail Kinetic Energy Impactor (KEI) spacecraft that impacts Apophis from a retrograde trajectory with a very high relative velocity (75-80 km/s) during one of its perihelion passages at about 0.75 AU would be a feasible option to do this. The spacecraft consists of a 160 m x 160 m, 168 kg solar sail assembly and a 150 kg impactor. Although conventional spacecraft can also achieve the required minimum deflection of 1 km for this approx. 320 m-sized object from a prograde trajectory, our solar sail KEI concept also allows the deflection of larger objects. In this paper, we also show that, even after Apophis has flown through one of the gravitational keyholes in 2029, solar sail Kinetic Energy Impactor (KEI) spacecraft are still a feasible option to prevent Apophis from impacting the Earth, but many KEIs would be required for consecutive impacts to increase the total Earth-miss distance to a safe value. In this paper, we elaborate potential pre- and post-2029 KEI impact scenarios for a launch in 2020, and investigate tradeoffs between different mission parameters.},
  language  = {en}
}
@inproceedings{HallmannHeideckerSchlottereretal.2016,
  author    = {Hallmann, Marcus and Heidecker, Ansgar and Schlotterer, Markus and Dachwald, Bernd},
  title     = {GTOC8: results and methods of team 15 DLR},
  series = {26th AAS/AIAA Space Flight Mechanics Meeting, Napa, CA},
  booktitle = {26th AAS/AIAA Space Flight Mechanics Meeting, Napa, CA},
  year      = {2016},
  abstract  = {This paper describes the results and methods used during the 8th Global Trajectory Optimization Competition (GTOC) of the DLR team. Trajectory optimization is crucial for most of the space missions and usually can be formulated as a global optimization problem. A lot of research has been done to different type of mission problems. The most demanding ones are low thrust transfers with e.g. gravity assist sequences. In that case the optimal control problem is combined with an integer problem. In most of the GTOCs we apply a filtering of the problem based on domain knowledge.},
  language  = {en}
}
@inproceedings{DupratDachwaldHilchenbachetal.2013,
  author    = {Duprat, J. and Dachwald, Bernd and Hilchenbach, M. and Engrand, Cecile and Espe, C. and Feldmann, M. and Francke, G. and G{\"o}r{\"o}g, Mark and L{\"u}sing, N. and Langenhorst, Falko},
  title     = {The MARVIN project: a micrometeorite harvester in Antarctic snow},
  series = {44th Lunar and Planetary Science Conference},
  booktitle = {44th Lunar and Planetary Science Conference},
  year      = {2013},
  abstract  = {MARVIN is an automated drilling and melting probe dedicated to collect pristine interplanetary dust particles (micrometeorites) from central Antarctica snow.},
  language  = {en}
}
@inproceedings{DachwaldSeboldtLoebetal.2007,
  author    = {Dachwald, Bernd and Seboldt, Wolfgang and Loeb, Horst W. and Schartner, Karl-Heinz},
  title     = {A comparison of SEP and NEP for a main belt asteroid sample return mission},
  series = {7th International Symposium on Launcher Technologies, Barcelona, Spain, 02-05 April 2007},
  booktitle = {7th International Symposium on Launcher Technologies, Barcelona, Spain, 02-05 April 2007},
  pages     = {1 -- 10},
  year      = {2007},
  abstract  = {Innovative interplanetary deep space missions, like a main belt asteroid sample return mission, require ever larger velocity increments (∆V s) and thus ever more demanding propulsion capabilities. Providing much larger exhaust velocities than chemical high-thrust systems, electric low-thrust space-propulsion systems can significantly enhance or even enable such high-energy missions. In 1995, a European-Russian Joint Study Group (JSG) presented a study report on "Advanced Interplanetary Missions Using Nuclear-Electric Propulsion" (NEP). One of the investigated reference missions was a sample return (SR) from the main belt asteroid (19) Fortuna. The envisaged nuclear power plant, Topaz-25, however, could not be realized and also the worldwide developments in space reactor hardware stalled. In this paper, we investigate, whether such a mission is also feasible using a solar electric propulsion (SEP) system and compare our SEP results to corresponding NEP results.},
  language  = {en}
}
@inproceedings{Dachwald2005,
  author    = {Dachwald, Bernd},
  title     = {Global optimization of low-thrust space missions using evolutionary neurocontrol},
  series = {Proceedings of the international workshop on global optimization},
  booktitle = {Proceedings of the international workshop on global optimization},
  pages     = {85 -- 90},
  year      = {2005},
  abstract  = {Low-thrust space propulsion systems enable flexible high-energy deep space missions, but the design and optimization of the interplanetary transfer trajectory is usually difficult. It involves much experience and expert knowledge because the convergence behavior of traditional local trajectory optimization methods depends strongly on an adequate initial guess. Within this extended abstract, evolutionary neurocontrol, a method that fuses artificial neural networks and evolutionary algorithms, is proposed as a smart global method for low-thrust trajectory optimization. It does not require an initial guess. The implementation of evolutionary neurocontrol is detailed and its performance is shown for an exemplary mission.},
  language  = {en}
}
@inproceedings{DachwaldBaturkinCoverstoneetal.2005,
  author    = {Dachwald, Bernd and Baturkin, Volodymyr and Coverstone, Victoria and Diedrich, Ben and Garbe, Gregory and G{\"o}rlich, Marianne and Leipold, Manfred and Lura, Franz and Macdonald, Malcolm and McInnes, Colin and Mengali, Giovanni and Quarta, Alessandro and Rios-Reyes, Leonel and Scheeres, Daniel J. and Seboldt, Wolfgang and Wie, Bong},
  title     = {Potential effects of optical solar sail degredation on trajectory design},
  series = {AAS/AIAA Astrodynamics Specialist},
  booktitle = {AAS/AIAA Astrodynamics Specialist},
  pages     = {1 -- 23},
  year      = {2005},
  abstract  = {The optical properties of the thin metalized polymer films that are projected for solar sails are assumed to be affected by the erosive effects of the space environment. Their degradation behavior in the real space environment, however, is to a considerable degree indefinite, because initial ground test results are controversial and relevant inspace tests have not been made so far. The standard optical solar sail models that are currently used for trajectory design do not take optical degradation into account, hence its potential effects on trajectory design have not been investigated so far. Nevertheless, optical degradation is important for high-fidelity solar sail mission design, because it decreases both the magnitude of the solar radiation pressure force acting on the sail and also the sail control authority. Therefore, we propose a simple parametric optical solar sail degradation model that describes the variation of the sail film's optical coefficients with time, depending on the sail film's environmental history, i.e., the radiation dose. The primary intention of our model is not to describe the exact behavior of specific film-coating combinations in the real space environment, but to provide a more general parametric framework for describing the general optical degradation behavior of solar sails. Using our model, the effects of different optical degradation behaviors on trajectory design are investigated for various exemplary missions.},
  language  = {en}
}
@inproceedings{HilleStumpfMayntzetal.2023,
  author    = {Hille, Sebastian and Stumpf, Eike and Mayntz, Joscha and Dahmann, Peter},
  title     = {Prediction of sound exposure caused by a landing motor glider with recuperating propellers},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-0211},
  year      = {2023},
  abstract  = {This paper presents an approach to predicting the sound exposure on the ground caused by a landing aircraft with recuperating propellers. The noise source along the trajectory of a flight specified for a steeper approach is simulated based on measurements of sound power levels and additional parameters of a single propeller placed in a wind tunnel. To validate the measured data/measurement results, these simulations are also supported by overflight measurements of a test aircraft. It is shown that the simple source models of propellers do not provide fully satisfactory results since the sound levels are estimated too low. Nevertheless, with a further reference comparison, margins for an acceptable increase in the sound power level of the aircraft on its now steeper approach path could be estimated. Thus, in this case, a +7 dB increase in SWL would not increase the SEL compared to the conventional approach within only 2 km ahead of the airfield.},
  language  = {en}
}
@inproceedings{HorikawaAshikagaYamaguchietal.2022,
  author    = {Horikawa, Atsushi and Ashikaga, Mitsugu and Yamaguchi, Masato and Ogino, Tomoyuki and Aoki, Shigeki and Wirsum, Manfred and Funke, Harald and Kusterer, Karsten},
  title     = {Combined heat and power supply demonstration of Micro-Mix Hydrogen Combustion Applied to M1A-17 Gas Turbine},
  series = {Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A)},
  booktitle = {Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A)},
  publisher = {American Society of Mechanical Engineers},
  address   = {Fairfield},
  isbn      = {978-0-7918-8599-4},
  doi       = {10.1115/GT2022-81620},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {Kawasaki Heavy Industries, Ltd. (KHI), Aachen University of Applied Sciences, and B\&B-AGEMA GmbH have investigated the potential of low NOx micro-mix (MMX) hydrogen combustion and its application to an industrial gas turbine combustor. Engine demonstration tests of a MMX combustor for the M1A-17 gas turbine with a co-generation system were conducted in the hydrogen-fueled power generation plant in Kobe City, Japan. This paper presents the results of the commissioning test and the combined heat and power (CHP) supply demonstration. In the commissioning test, grid interconnection, loading tests and load cut-off tests were successfully conducted. All measurement results satisfied the Japanese environmental regulation values. Dust and soot as well as SOx were not detected. The NOx emissions were below 84 ppmv at 15 \% O2. The noise level at the site boundary was below 60 dB. The vibration at the site boundary was below 45 dB. During the combined heat and power supply demonstration, heat and power were supplied to neighboring public facilities with the MMX combustion technology and 100 \% hydrogen fuel. The electric power output reached 1800 kW at which the NOx emissions were 72 ppmv at 15 \% O2, and 60 \%RH. Combustion instabilities were not observed. The gas turbine efficiency was improved by about 1 \% compared to a non-premixed type combustor with water injection as NOx reduction method. During a total equivalent operation time of 1040 hours, all combustor parts, the M1A-17 gas turbine as such, and the co-generation system were without any issues.},
  language  = {en}
}
@inproceedings{MoehrenBergmannJanseretal.2023,
  author    = {M{\"o}hren, Felix and Bergmann, Ole and Janser, Frank and Braun, Carsten},
  title     = {On the determination of harmonic propeller loads},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-2404},
  pages     = {12 Seiten},
  year      = {2023},
  abstract  = {Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures.},
  language  = {en}
}
@inproceedings{FunkeBeckmannStefanetal.2023,
  author    = {Funke, Harald and Beckmann, Nils and Stefan, Lukas and Keinz, Jan},
  title     = {Hydrogen combustor integration study for a medium range aircraft engine using the dry-low NOx "Micromix" combustion principle},
  series = {Proceedings of the ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition. Volume 1: Aircraft Engine. Boston, Massachusetts, USA. June 26-30, 2023},
  booktitle = {Proceedings of the ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition. Volume 1: Aircraft Engine. Boston, Massachusetts, USA. June 26-30, 2023},
  publisher = {ASME},
  address   = {New York},
  isbn      = {978-0-7918-8693-9},
  doi       = {10.1115/GT2023-102370},
  pages     = {12 Seiten},
  year      = {2023},
  abstract  = {The feasibility study presents results of a hydrogen combustor integration for a Medium-Range aircraft engine using the Dry-Low-NOₓ Micromix combustion principle. Based on a simplified Airbus A320-type flight mission, a thermodynamic performance model of a kerosene and a hydrogen-powered V2530-A5 engine is used to derive the thermodynamic combustor boundary conditions. A new combustor design using the Dry-Low NOx Micromix principle is investigated by slice model CFD simulations of a single Micromix injector for design and off-design operation of the engine. Combustion characteristics show typical Micromix flame shapes and good combustion efficiencies for all flight mission operating points. Nitric oxide emissions are significant below ICAO CAEP/8 limits. For comparison of the Emission Index (EI) for NOₓ emissions between kerosene and hydrogen operation, an energy (kerosene) equivalent Emission Index is used. A full 15° sector model CFD simulation of the combustion chamber with multiple Micromix injectors including inflow homogenization and dilution and cooling air flows investigates the combustor integration effects, resulting NOₓ emission and radial temperature distributions at the combustor outlet. The results show that the integration of a Micromix hydrogen combustor in actual aircraft engines is feasible and offers, besides CO₂ free combustion, a significant reduction of NOₓ emissions compared to kerosene operation.},
  language  = {en}
}
@inproceedings{GehlerOberBloebaumDachwald2009,
  author    = {Gehler, M. and Ober-Bl{\"o}baum, S. and Dachwald, Bernd},
  title     = {Application of discrete mechanics and optimal control to spacecraft in non-keplerian motion around small solar system bodies},
  series = {Procceedings of the 60th International Astronautical Congress},
  booktitle = {Procceedings of the 60th International Astronautical Congress},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-161567908-9},
  pages     = {1360 -- 1371},
  year      = {2009},
  abstract  = {Prolonged operations close to small solar system bodies require a sophisticated control logic to minimize propellant mass and maximize operational efficiency. A control logic based on Discrete Mechanics and Optimal Control (DMOC) is proposed and applied to both conventionally propelled and solar sail spacecraft operating at an arbitrarily shaped asteroid in the class of Itokawa. As an example, stand-off inertial hovering is considered, recently identified as a challenging part of the Marco Polo mission. The approach is easily extended to stand-off orbits. We show that DMOC is applicable to spacecraft control at small objects, in particular with regard to the fact that the changes in gravity are exploited by the algorithm to optimally control the spacecraft position. Furthermore, we provide some remarks on promising developments.},
  language  = {en}
}
@inproceedings{DachwaldWurm2009,
  author    = {Dachwald, Bernd and Wurm, P.},
  title     = {Design concept and modeling of an advanced solar photon thruster},
  series = {Advances in the Astronautical Sciences},
  booktitle = {Advances in the Astronautical Sciences},
  publisher = {American Astronautical Society},
  address   = {San Diego, Calif.},
  isbn      = {978-087703554-1},
  issn      = {00653438},
  pages     = {723 -- 740},
  year      = {2009},
  abstract  = {The so-called "compound solar sail", also known as "Solar Photon Thruster" (SPT), holds the potential of providing significant performance advantages over the flat solar sail. Previous SPT design concepts, however, do not consider shadowing effects and multiple reflections of highly concentrated solar radiation that would inevitably destroy the gossamer sail film. In this paper, we propose a novel advanced SPT (ASPT) design concept that does not suffer from these oversimplifications. We present the equations that describe the thrust force acting on such a sail system and compare its performance with respect to the conventional flat solar sail.},
  language  = {en}
}
@inproceedings{DachwaldWurm2009,
  author    = {Dachwald, Bernd and Wurm, P.},
  title     = {Mission analysis for an advanced solar photon thruster},
  series = {60th International Astronautical Congress 2009, IAC 2009},
  volume    = {Vol. 8},
  booktitle = {60th International Astronautical Congress 2009, IAC 2009},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-161567908-9},
  pages     = {6838 -- 6851},
  year      = {2009},
  abstract  = {The so-called "compound solar sail", also known as "Solar Photon Thruster" (SPT), is a solar sail design concept, for which the two basic functions of the solar sail, namely light collection and thrust direction, are uncoupled. In this paper, we introduce a novel SPT concept, termed the Advanced Solar Photon Thruster (ASPT). This model does not suffer from the simplified assumptions that have been made for the analysis of compound solar sails in previous studies. We present the equations that describe the force, which acts on the ASPT. After a detailed design analysis, the performance of the ASPT with respect to the conventional flat solar sail (FSS) is investigated for three interplanetary mission scenarios: An Earth-Venus rendezvous, where the solar sail has to spiral towards the Sun, an Earth-Mars rendezvous, where the solar sail has to spiral away from the Sun, and an Earth-NEA rendezvous (to near-Earth asteroid 1996FG3), where a large orbital eccentricity change is required. The investigated solar sails have realistic near-term characteristic accelerations between 0.1 and 0.2mm/s2. Our results show that a SPT is not superior to the flat solar sail unless very idealistic assumptions are made.},
  language  = {en}
}
@inproceedings{GoettenFingerHavermannetal.2020,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Full Configuration Drag Estimation of Small-to-Medium Range UAVs and its Impact on Initial Sizing Optimization},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@inproceedings{BergmannGoettenBraunetal.2022,
  author    = {Bergmann, Ole and G{\"o}tten, Falk and Braun, Carsten and Janser, Frank},
  title     = {Comparison and evaluation of blade element methods against RANS simulations and test data},
  series = {CEAS Aeronautical Journal},
  volume    = {13},
  booktitle = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-022-00579-1},
  pages     = {535 -- 557},
  year      = {2022},
  abstract  = {This paper compares several blade element theory (BET) method-based propeller simulation tools, including an evaluation against static propeller ground tests and high-fidelity Reynolds-Average Navier Stokes (RANS) simulations. Two proprietary propeller geometries for paraglider applications are analysed in static and flight conditions. The RANS simulations are validated with the static test data and used as a reference for comparing the BET in flight conditions. The comparison includes the analysis of varying 2D aerodynamic airfoil parameters and different induced velocity calculation methods. The evaluation of the BET propeller simulation tools shows the strength of the BET tools compared to RANS simulations. The RANS simulations underpredict static experimental data within 10\% relative error, while appropriate BET tools overpredict the RANS results by 15-20\% relative error. A variation in 2D aerodynamic data depicts the need for highly accurate 2D data for accurate BET results. The nonlinear BET coupled with XFOIL for the 2D aerodynamic data matches best with RANS in static operation and flight conditions. The novel BET tool PropCODE combines both approaches and offers further correction models for highly accurate static and flight condition results.},
  language  = {en}
}
@inproceedings{GeibenGoettenHavermann2020,
  author    = {Geiben, Benedikt and G{\"o}tten, Falk and Havermann, Marc},
  title     = {Aerodynamic analysis of a winged sub-orbital spaceplane},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@inproceedings{HippeFingerGoettenetal.2020,
  author    = {Hippe, Jonas and Finger, Felix and G{\"o}tten, Falk and Braun, Carsten},
  title     = {Propulsion System Qualification of a 25 kg VTOL-UAV: Hover Performance of Single and Coaxial Rotors and Wind-Tunnel Experiments on Cruise Propellers},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, C.},
  title     = {On Aircraft Design Under the Consideration of Hybrid-Electric Propulsion Systems},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_99},
  pages     = {1261 -- 1272},
  year      = {2019},
  abstract  = {A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology.},
  language  = {en}
}
@inproceedings{GoettenFingerBraunetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Braun, Carsten and Havermann, Marc and Bil, C. and Gomez, F.},
  title     = {Empirical Correlations for Geometry Build-Up of Fixed Wing Unmanned Air Vehicles},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_109},
  pages     = {1365 -- 1381},
  year      = {2019},
  abstract  = {The results of a statistical investigation of 42 fixed-wing, small to medium sized (20 kg-1000 kg) reconnaissance unmanned air vehicles (UAVs) are presented. Regression analyses are used to identify correlations of the most relevant geometry dimensions with the UAV's maximum take-off mass. The findings allow an empirical based geometry-build up for a complete unmanned aircraft by referring to its take-off mass only. This provides a bridge between very early design stages (initial sizing) and the later determination of shapes and dimensions. The correlations might be integrated into a UAV sizing environment and allow designers to implement more sophisticated drag and weight estimation methods in this process. Additional information on correlation factors for a rough drag estimation methodology indicate how this technique can significantly enhance the accuracy of early design iterations.},
  language  = {en}
}