@article{KahmannRauschPluemeretal.2022,
  author    = {Kahmann, Stephanie L. and Rausch, Valentin and Pl{\"u}mer, Jonathan and M{\"u}ller, Lars P. and Pieper, Martin and Wegmann, Kilian},
  title     = {The automized fracture edge detection and generation of three-dimensional fracture probability heat maps},
  series = {Medical Engineering \& Physics},
  volume    = {2022},
  journal   = {Medical Engineering \& Physics},
  number    = {110},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1350-4533},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1-2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further.},
  language  = {en}
}
@article{JellinghausGoettscheHoffschmidt2006,
  author    = {Jellinghaus, Sabine and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard},
  title     = {Beleuchtung mit gesteuertem Farblicht - Bewertung eines Prototypen},
  series = {Zw{\"o}lftes Symposium Innovative Lichttechnik in Geb{\"a}uden : 26./27. Januar 2006, Kloster Banz, Bad Staffelstein / OTTI - Training, Seminare, Tagungen. [Fachliche Gesamtleitung: Claus Steffan. Veranst.: OTTI, Bereich Erneuerbare Energien. Mitveranst.: Architektenkammer Baden-W{\"u}rttemberg, Stuttgart ...] / . - (Wissen f{\"u}r Profis)},
  journal   = {Zw{\"o}lftes Symposium Innovative Lichttechnik in Geb{\"a}uden : 26./27. Januar 2006, Kloster Banz, Bad Staffelstein / OTTI - Training, Seminare, Tagungen. [Fachliche Gesamtleitung: Claus Steffan. Veranst.: OTTI, Bereich Erneuerbare Energien. Mitveranst.: Architektenkammer Baden-W{\"u}rttemberg, Stuttgart ...] / . - (Wissen f{\"u}r Profis)},
  publisher = {OTTI, Bereich Erneuerbare Energien},
  address   = {Regensburg},
  isbn      = {3-934681-43-3},
  pages     = {89 -- 93},
  year      = {2006},
  language  = {de}
}
@article{RegerKuhnhenneHachuletal.2019,
  author    = {Reger, Vitali and Kuhnhenne, Markus and Hachul, Helmut and D{\"o}ring, Bernd and Blanke, Tobias and G{\"o}ttsche, Joachim},
  title     = {Plusenergiegeb{\"a}ude 2.0 in Stahlleichtbauweise},
  series = {Stahlbau},
  volume    = {88},
  journal   = {Stahlbau},
  number    = {6},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1049 (E-journal), 0038-9145 (print)},
  doi       = {10.1002/stab.201900034},
  pages     = {522 -- 528},
  year      = {2019},
  language  = {de}
}
@article{KuperjansStarkeEsseretal.2000,
  author    = {Kuperjans, Isabel and Starke, M. and Esser, J. and Meyer, J. and Donner, O.},
  title     = {Analyse und Konzeption von Energieanlagen unter {\"o}kologischen, wirtschaftlichen und technischen Gesichtspunkten},
  series = {WLB : Umwelttechnik f{\"u}r Industrie und Kommune},
  volume    = {44},
  journal   = {WLB : Umwelttechnik f{\"u}r Industrie und Kommune},
  number    = {11/12},
  issn      = {0341-2679},
  pages     = {26 -- 29},
  year      = {2000},
  language  = {de}
}
@article{BreitbachAltesSzimmat1989,
  author    = {Breitbach, Gerd and Altes, J{\"u}rgen and Szimmat, J.},
  title     = {Anwendung der Finite-Element-Methode bei der Berechnung des W{\"a}rmetransports durch Strahlung / J. Altes ; G. Breitbach ; J. Szimmat},
  series = {International FEM-Congress : Baden-Baden, Federal Republic of Germany, 17./18. November 1986},
  journal   = {International FEM-Congress : Baden-Baden, Federal Republic of Germany, 17./18. November 1986},
  publisher = {IKO Software Service GmbH},
  address   = {Stuttgart},
  pages     = {127 -- 148},
  year      = {1989},
  language  = {de}
}
@article{ButenwegFehling2012,
  author    = {Butenweg, Christoph and Fehling, Ekkehard},
  title     = {Hintergrund f{\"u}r die vereinfachten Regeln bei Mauerwerksgeb{\"a}uden im Erdbebenfall},
  series = {Mauerwerk : European journal of masonry},
  volume    = {16},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201200537},
  pages     = {127 -- 137},
  year      = {2012},
  abstract  = {Bei der Ausarbeitung des nationalen Anwendungsdokumentes zur DIN EN 1998-1 waren die in der ENV-Fassung enthaltenen vereinfachten Regeln im Lichte aktueller Forschungsergebnisse zu {\"u}berpr{\"u}fen und zu {\"u}berarbeiten. Die gleiche Aufgabe stellte sich auch f{\"u}r die Neufassung der DIN 4149. In beiden F{\"a}llen sind neben konstruktiven Regeln f{\"u}r die Art und Anordnung der zur Geb{\"a}udeaussteifung heranzuziehenden W{\"a}nde im Grundriss Tabellen enthalten, die unter bestimmten Bedingungen den Entfall eines rechnerischen Nachweises der Tragw{\"a}nde im Erdbebenfall erm{\"o}glichen. Dies ist f{\"u}r Schwachbebengebiete, wie sie in Deutschland und anderen L{\"a}ndern Mitteleuropas anzutreffen sind, sinnvoll, um unn{\"o}tigen Rechenaufwand sowie Probleme mit der F{\"u}hrbarkeit von Nachweisen so weit wie m{\"o}glich auszuschalten. Im vorliegenden Beitrag werden die Hintergr{\"u}nde der vereinfachten Regeln diskutiert und die Ergebnisse der Anwendung mit verschiedenen Rechenverfahren verglichen und bewertet.},
  language  = {de}
}
@article{ButenwegGellert2012,
  author    = {Butenweg, Christoph and Gellert, Christoph},
  title     = {Integrale Geb{\"a}udeplanung am Beispiel eines Geschossbaus in Ziegelmauerwerk},
  series = {Mauerwerk : European journal of masonry},
  volume    = {16},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {5},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201200550},
  pages     = {247 -- 254},
  year      = {2012},
  abstract  = {Moderne Mauerwerksbauten m{\"u}ssen nach heutigen Anforderungen architektonisch, statisch, energetisch sowie schall- und brandschutztechnisch optimal ausgelegt sein. Aufgrund der Komplexit{\"a}t und engen Verzahnung der einzelnen Anforderungen ist eine integrale Geb{\"a}udeplanung zur Erzielung einer qualitativ hochwertigen Bauwerksl{\"o}sung unbedingt notwendig. Diese erfordert von den Fachplanern vertieftes Spezialwissen in den verschiedenen Bereichen, um insbesondere die Schnittstellen und Bauwerksdetails korrekt zu planen und auszuf{\"u}hren. Der Beitrag stellt die integrale Geb{\"a}udeplanung am Beispiel eines Geschossbaus in Ziegelbauweise mit L{\"o}sungen f{\"u}r wesentliche Detailpunkte vor},
  language  = {de}
}
@article{ButenwegHoltschoppen2012,
  author    = {Butenweg, Christoph and Holtschoppen, Britta},
  title     = {Neuer VCI-Leitfaden f{\"u}r die erdbebensichere Auslegung von Industrieanlagen},
  series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik},
  volume    = {87},
  journal   = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {1436-4867 (E-Journal); 0005-6650 (Print)},
  pages     = {18},
  year      = {2012},
  language  = {de}
}
@article{HenriquesJuradoGrieseretal.2020,
  author    = {Henriques, A. and Jurado, B. and Grieser, M. and Denis-Petit, D. and Chiron, T. and Gaudefroy, L. and Glorius, J. and Langer, Christoph and Litvinov, Yu. A. and Mathieu, L. and Meot, V. and Perez-Sanchez, R. and Pibernat, J. and Reifarth, R. and Roig, O. and Thomas, B. A. and Thomas, B. A. and Thomas, J. C. and Tsekhanovich, I.},
  title     = {Indirect measurements of neutron cross-secti at heavy-ion storage rings},
  series = {Journal of Physics: Conference Series},
  volume    = {1668},
  journal   = {Journal of Physics: Conference Series},
  number    = {Art. 012019},
  publisher = {IOP},
  address   = {Bristol},
  doi       = {10.1088/1742-6596/1668/1/012019},
  year      = {2020},
  abstract  = {Cross sections for neutron-induced reactions of short-lived nuclei are essential for nuclear astrophysics since these reactions in the stars are responsible for the production of most heavy elements in the universe. These reactions are also key in applied domains like energy production and medicine. Nevertheless, neutron-induced cross-section measurements can be extremely challenging or even impossible to perform due to the radioactivity of the targets involved. Indirect measurements through the surrogate-reaction method can help to overcome these difficulties. The surrogate-reaction method relies on the use of an alternative reaction that will lead to the formation of the same excited nucleus as in the neutron-induced reaction of interest. The decay probabilities (for fission, neutron and gamma-ray emission) of the nucleus produced via the surrogate reaction allow one to constrain models and the prediction of the desired neutron cross sections. We propose to perform surrogate reaction measurements in inverse kinematics at heavy-ion storage rings, in particular at the CRYRING@ESR of the GSI/FAIR facility. We present the conceptual idea of the most promising setup to measure for the first time simultaneously the fission, neutron and gamma-ray emission probabilities. The results of the first simulations considering the 238U(d,d') reaction are shown, as well as new technical developments that are being carried out towards this set-up.},
  language  = {en}
}
@article{FleischhakerEversDey2010,
  author    = {Fleischhaker, Robert and Evers, J{\"o}rg and Dey, Tarak N.},
  title     = {Phase modulation induced by cooperative effects in electromagnetically induced transparency},
  series = {Physical Review A - Atomic, molecular, and optical physics},
  volume    = {82},
  journal   = {Physical Review A - Atomic, molecular, and optical physics},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {1050-2947},
  doi       = {10.1103/PhysRevA.82.013815},
  pages     = {013815},
  year      = {2010},
  abstract  = {We analyze the influence of dipole-dipole interactions in an electromagnetically induced transparency set up for a density at the onset of cooperative effects. To this end, we include mean-field models for the influence of local-field corrections and radiation trapping into our calculation. We show both analytically and numerically that the polarization contribution to the local field strongly modulates the phase of a weak pulse. We give an intuitive explanation for this local-field-induced phase modulation and demonstrate that it distinctively differs from the nonlinear self-phase-modulation that a strong pulse experiences in a Kerr medium.},
  language  = {en}
}
@article{IlleSchrammAdametal.2008,
  author    = {Ille, Fabian and Schramm, S. and Adam, M. and Backes, K. and Faber, Christian and Anthrakidis, Anette},
  title     = {Kraft-W{\"a}rme-K{\"a}lte-Kopplung im Leistungsbereich von 10 kW mit periodisch arbeitender Sorptionsmaschine},
  series = {VDI-Tage der Geb{\"a}udetechnik 2008 : Tagung Dortmund, 28. und 29. Mai 2008 / VDI-Gesellschaft Technische Geb{\"a}udeausr{\"u}stung},
  journal   = {VDI-Tage der Geb{\"a}udetechnik 2008 : Tagung Dortmund, 28. und 29. Mai 2008 / VDI-Gesellschaft Technische Geb{\"a}udeausr{\"u}stung},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092043-6},
  pages     = {103 -- 116},
  year      = {2008},
  language  = {de}
}
@article{GeimerSauerbornHoffschmidtetal.2010,
  author    = {Geimer, Konstantin and Sauerborn, Markus and Hoffschmidt, Bernhard and Schmitz, Mark and G{\"o}ttsche, Joachim},
  title     = {Test facility for absorber specimens of solar tower power plants},
  series = {Advances in Science and Technology},
  volume    = {74},
  journal   = {Advances in Science and Technology},
  publisher = {Trans Tech Publications},
  address   = {Baech},
  doi       = {10.4028/www.scientific.net/AST.74.266},
  pages     = {266 -- 271},
  year      = {2010},
  abstract  = {The Solar-Institute J{\"u}lich (SIJ) has initiated the construction of the first and only German solar tower power plant and is now involved in the accompanying research. The power plant for experimental and demonstration purposes in the town of J{\"u}lich started supplying electric energy in the beginning of 2008. The central receiver plant features as central innovation an open volumetric receiver, consisting of porous ceramic elements that simultaneously absorb the concentrated sunlight and transfer the heat to ambient air passing through the pores so that an average temperature of 680°C is reached. The subsequent steam cycle generates up to 1.5 MWe. A main field of research at the SIJ is the optimization of the absorber structures. To analyze the capability of new absorber specimens a special test facility was developed and set up in the laboratory. A high-performance near-infrared radiator offers for single test samples a variable and repeatable beam with a power of up to 320 kW/m² peak. The temperatures achieved on the absorber surface can reach more than 1000°C. To suck ambient air through the open absorber - like on the tower - it is mounted on a special blower system. An overview about the test facility and some recent results will be presented.},
  language  = {en}
}
@article{AlexopoulosHoffschmidt2010,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard},
  title     = {Solarthermische Kraftwerke mit thermischen Speichern},
  series = {Chemie Ingenieur Technik},
  volume    = {82},
  journal   = {Chemie Ingenieur Technik},
  number    = {9},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  isbn      = {1522-2640},
  doi       = {10.1002/cite.201050678},
  pages     = {1606},
  year      = {2010},
  abstract  = {Solarthermische Kraftwerke stellen eine bedeutende Technologieoption f{\"u}r einen nachhaltigen Energiemix der Zukunft dar. Sie konzentrieren die Strahlung der Sonne, erzeugen W{\"a}rme und wandeln diese mit konventioneller Kraftwerkstechnik in Strom um. Die W{\"a}rme kann auch gespeichert werden, so dass der Betrieb w{\"a}hrend des Durchzugs von Wolken m{\"o}glich ist und bis in die Abendstunden hinein verl{\"a}ngert werden kann. Zu den solarthermischen Kraftwerken geh{\"o}ren neben der Parabolrinne und dem Solarturm der Fresnel-Kollektor und die Dish-Stirling-Systeme. Im Zuge einer sp{\"a}teren Vergr{\"o}ßerung des Solarfeldes von Solarkraftwerken kann mithilfe von thermischen Energiespeichern die solare Energieerzeugung bei gleichbleibender Kraftwerksleistung sukzessiv bis um den Faktor 3 erweitert werden. Es besteht so die M{\"o}glichkeit einer massiven Substitution von fossilen Brennstoffen.Bei den ersten solarthermischen Speichern f{\"u}r die SEGS-Parabolrinnekraftwerke wurde {\"O}l als Speichermedium eingesetzt. Ein weiteres Speichermedium ist Salzschmelze, die im Andasol-1-Projekt in Spanien sowie bei Solarturmkraftwerken eingesetzt wird. Beton ist ein weiteres m{\"o}gliches Speichermaterial f{\"u}r Parabolrinnensysteme. Eine weitere Alternative bei einem Solarturmkraftwerk mit Luft als W{\"a}rmetr{\"a}germedium ist die Verwendung von keramischen Feuerfestmaterialien in Form von Sch{\"u}ttungen oder stapelbaren, por{\"o}sen Elementen. In J{\"u}lich wurde das weltweit erste solarthermische Turmkraftwerk mit einer Leistung von 1,5 MWe, das Luft als W{\"a}rmetr{\"a}germedium einsetzt und einen solchen Speicher verwendet, gebaut.},
  language  = {de}
}
@article{KernFrentzelBehrens2010,
  author    = {Kern, Alexander and Frentzel, Ralf and Behrens, J{\"o}rg},
  title     = {Simulation of the transient voltages in the auxiliary power network of a large power plant in case of a direct lightning strike to the high-voltage overhead transmission line},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-88-905519-0-1},
  doi       = {10.1109/ICLP.2010.7845756},
  pages     = {749-1 -- 749-7},
  year      = {2010},
  abstract  = {Large power plants can be endangered by lightning strikes with possible consequences regarding their safety and availability. A special scenario is a lightning strike to the HV overhead transmission line close to the power plant's connection to the power grid. If then additionally a so-called shielding failure of the overhead ground wire on top of the overhead transmission line is assumed, i.e. the lightning strikes directly into a phase conductor, this is an extreme electromagnetic disturbance. The paper deals with the numerical simulation of such a lightning strike and the consequences on the components of the power plant's auxiliary power network connected to different voltage levels.},
  language  = {en}
}
@article{BouquegneauKernRousseau2010,
  author    = {Bouquegneau, Christian and Kern, Alexander and Rousseau, Alain},
  title     = {Lightning safety guidelines},
  pages     = {6 Seiten},
  year      = {2010},
  abstract  = {This paper introduces lightning to the layman, noting the right behaviour in front of thunderstorms as well as protective measures against lightning. It also contributes to the prevention of lightning injuries and damages. This report was prepared by the authors inside the AHG1 Group for IEC TC81 (Lightning Protection).},
  language  = {en}
}
@article{KernKloetersPferdemenges2010,
  author    = {Kern, Alexander and Kl{\"o}ters, Georg and Pferdemenges, J{\"o}rg},
  title     = {Optimised protection against lightning for the signalling and safety systems of level crossings on non-electrified railway lines},
  series = {RTR : European Rail Technology Review},
  volume    = {50},
  journal   = {RTR : European Rail Technology Review},
  number    = {2},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0079-9548},
  year      = {2010},
  language  = {en}
}
@article{KernSchelthoffMathieu2010,
  author    = {Kern, Alexander and Schelthoff, Christof and Mathieu, Moritz},
  title     = {Probability of lightning strikes to air-terminations of structures using the electro-geometrical model theory and the statistics of lightning current parameters},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-88-905519-0-1},
  doi       = {10.1109/ICLP.2010.7845757},
  pages     = {750-1 -- 750-8},
  year      = {2010},
  abstract  = {Planning the air-terminations for a structure to be protected the use of the rolling-sphere method (electro-geometrical model) is the best way from the physics of lightning point-of-view. Therefore, international standards prefer this method. However, using the rolling-sphere method only results in possible point-of-strikes on a structure without giving information about the probability of strikes at the individual points compared to others.},
  language  = {en}
}
@article{KernSchelthoffMathieu2010,
  author    = {Kern, Alexander and Schelthoff, Christof and Mathieu, Moritz},
  title     = {Die dynamische Blitzkugel : Wahrscheinlichkeitsberechnung f{\"u}r Blitzeinschl{\"a}ge in Geb{\"a}ude},
  series = {de - Fachzeitschrift f{\"u}r das Elektrohandwerk},
  journal   = {de - Fachzeitschrift f{\"u}r das Elektrohandwerk},
  number    = {13-14},
  publisher = {H{\"u}thig},
  address   = {Heidelberg},
  issn      = {2509-517X},
  pages     = {24 -- 29},
  year      = {2010},
  language  = {de}
}