@inproceedings{ŠakićMilijašMarinkovićetal.2021,
  author    = {Šakić, Bogdan and Milijaš, Aleksa and Marinković, Marko and Butenweg, Christoph and Klinkel, Sven},
  title     = {Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load},
  series = {Proceedings of COMPDYN 2021},
  booktitle = {Proceedings of COMPDYN 2021},
  editor    = {Papadrakakis, Manolis and Fragiadakis, Michalis},
  publisher = {National Technical University of Athens},
  address   = {Athen},
  isbn      = {9786188507258},
  issn      = {2623-3347},
  doi       = {10.7712/120121.8527.18913},
  pages     = {808 -- 828},
  year      = {2021},
  abstract  = {Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic.},
  language  = {en}
}
@article{ButenwegBursiPaolaccietal.2021,
  author    = {Butenweg, Christoph and Bursi, Oreste S. and Paolacci, Fabrizio and Marinković, Marko and Lanese, Igor and Nardin, Chiara and Quinci, Gianluca},
  title     = {Seismic performance of an industrial multi-storey frame structure with process equipment subjected to shake table testing},
  series = {Engineering Structures},
  volume    = {243},
  journal   = {Engineering Structures},
  number    = {15},
  editor    = {Yang, J.},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0141-0296},
  doi       = {10.1016/j.engstruct.2021.112681},
  year      = {2021},
  abstract  = {Past earthquakes demonstrated the high vulnerability of industrial facilities equipped with complex process technologies leading to serious damage of process equipment and multiple and simultaneous release of hazardous substances. Nonetheless, current standards for seismic design of industrial facilities are considered inadequate to guarantee proper safety conditions against exceptional events entailing loss of containment and related consequences. On these premises, the SPIF project -Seismic Performance of Multi-Component Systems in Special Risk Industrial Facilities- was proposed within the framework of the European H2020 SERA funding scheme. In detail, the objective of the SPIF project is the investigation of the seismic behaviour of a representative industrial multi-storey frame structure equipped with complex process components by means of shaking table tests. Along this main vein and in a performance-based design perspective, the issues investigated in depth are the interaction between a primary moment resisting frame (MRF) steel structure and secondary process components that influence the performance of the whole system; and a proper check of floor spectra predictions. The evaluation of experimental data clearly shows a favourable performance of the MRF structure, some weaknesses of local details due to the interaction between floor crossbeams and process components and, finally, the overconservatism of current design standards w.r.t. floor spectra predictions.},
  language  = {en}
}
@inproceedings{HandschuhStollenwerkBorchert2021,
  author    = {Handschuh, Nils and Stollenwerk, Dominik and Borchert, J{\"o}rg},
  title     = {Operation of thermal storage power plants under high renewable grid penetration},
  series = {NEIS 2021: Conference on Sustainable Energy Supply and Energy Storage Systems},
  booktitle = {NEIS 2021: Conference on Sustainable Energy Supply and Energy Storage Systems},
  publisher = {VDE Verlag},
  address   = {Berlin},
  isbn      = {978-3-8007-5651-3},
  pages     = {261 -- 265},
  year      = {2021},
  abstract  = {The planned coal phase-out in Germany by 2038 will lead to the dismantling of power plants with a total capacity of approx. 30 GW. A possible further use of these assets is the conversion of the power plants to thermal storage power plants; the use of these power plants on the day-ahead market is considerably limited by their technical parameters. In this paper, the influence of the technical boundary conditions on the operating times of these storage facilities is presented. For this purpose, the storage power plants were described as an MILP problem and two price curves, one from 2015 with a relatively low renewable penetration (33 \%) and one from 2020 with a high renewable energy penetration (51 \%) are compared. The operating times were examined as a function of the technical parameters and the critical influencing factors were investigated. The thermal storage power plant operation duration and the energy shifted with the price curve of 2020 increases by more than 25 \% compared to 2015.},
  language  = {en}
}
@inproceedings{KernImaniVashianiTimmermanns2021,
  author    = {Kern, Alexander and Imani Vashiani, Anahita and Timmermanns, Tobias},
  title     = {Threat for human beings due to touch voltages and body currents caused by direct lightning strikes in case of non-isolated lightning protection systems using natural components},
  series = {35th International Conference on Lightning Protection (ICLP) and XVI International Symposium on Lightning Protection (SIPDA)},
  booktitle = {35th International Conference on Lightning Protection (ICLP) and XVI International Symposium on Lightning Protection (SIPDA)},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {978-1-6654-2346-5},
  doi       = {10.1109/ICLPandSIPDA54065.2021.9627465},
  pages     = {8 Seiten},
  year      = {2021},
  abstract  = {For typical cases of non-isolated lightning protection systems (LPS) the impulse currents are investigated which may flow through a human body directly touching a structural part of the LPS. Based on a basic LPS model with conventional down-conductors especially the cases of external and internal steel columns and metal fa{\c{c}}ades are considered and compared. Numerical simulations of the line quantities voltages and currents in the time domain are performed with an equivalent circuit of the entire LPS. As a result it can be stated that by increasing the number of conventional down-conductors and external steel columns the threat for a human being can indeed be reduced, but not down to an acceptable limit. In case of internal steel columns used as natural down-conductors the threat can be reduced sufficiently, depending on the low-resistive connection of the steel columns to the lightning equipotential bonding or the earth termination system, resp. If a metal fa{\c{c}}ade is used the threat for human beings touching is usually very low, if the fa{\c{c}}ade is sufficiently interconnected and multiply connected to the lightning equipotential bonding or the earth termination system, resp.},
  language  = {en}
}
@book{Pieper2021,
  author    = {Pieper, Martin},
  title     = {Quantum mechanics: Introduction to mathematical formulation},
  publisher = {Springer},
  address   = {Wiesbaden},
  isbn      = {978-3-658-32644-9},
  doi       = {10.1007/978-3-658-32645-6},
  pages     = {XIII, 33},
  year      = {2021},
  abstract  = {Anyone who has always wanted to understand the hieroglyphs on Sheldon's blackboard in the TV series The Big Bang Theory or who wanted to know exactly what the fate of Schr{\"o}dinger's cat is all about will find a short, descriptive introduction to the world of quantum mechanics in this essential. The text particularly focuses on the mathematical description in the Hilbert space. The content goes beyond popular scientific presentations, but is nevertheless suitable for readers without special prior knowledge thanks to the clear examples.},
  language  = {en}
}
@incollection{JordanKatzPieper2021,
  author    = {Jordan, Frank and Katz, Christiane and Pieper, Martin},
  title     = {Online-Kollaboration in der Mathematik: Ein Design-Based-Research-Projekt},
  series = {Forschungsimpulse f{\"u}r hybrides Lehren und Lernen an Hochschulen},
  booktitle = {Forschungsimpulse f{\"u}r hybrides Lehren und Lernen an Hochschulen},
  publisher = {TH K{\"o}ln},
  address   = {K{\"o}ln},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:832-cos4-9465},
  pages     = {245 -- 261},
  year      = {2021},
  abstract  = {Die Studie er{\"o}rtert anhand eines Fallbeispiels aus der Mathematik f{\"u}r Ingenieur*innen, wie didaktische Gestaltungsprinzipien f{\"u}r Soziale Pr{\"a}senz, Kollaboration und das L{\"o}sen von praxisnahen Problemen mit mathematischem Denken in einer Online-Umgebung aussehen k{\"o}nnen. Hierf{\"u}r zieht der Beitrag den forschungsmethodologischen Rahmen Design-Based Research (DBR) hinzu und berichtet {\"u}ber Zwischenergebnisse. DBR wird an dieser Stelle als eine systematische Herangehensweise an kurzfristige Lehrver{\"a}nderungen und als Chance auf dem Weg zu einer neuen Hochschullehre nach der COVID-19-Pandemie dargestellt, die theoretische und empirische Erkenntnisse mit Praxisverkn{\"u}pfung und -relevanz vereint.},
  language  = {de}
}
@article{HeelDiktaBraekers2021,
  author    = {Heel, Mareike van and Dikta, Gerhard and Braekers, Roel},
  title     = {Bootstrap based goodness‑of‑fit tests for binary multivariate regression models},
  series = {Journal of the Korean Statistical Society},
  volume    = {51},
  journal   = {Journal of the Korean Statistical Society},
  publisher = {Springer Nature},
  address   = {Singapur},
  issn      = {2005-2863 (Online)},
  doi       = {10.1007/s42952-021-00142-4},
  pages     = {28 Seiten},
  year      = {2021},
  abstract  = {We consider a binary multivariate regression model where the conditional expectation of a binary variable given a higher-dimensional input variable belongs to a parametric family. Based on this, we introduce a model-based bootstrap (MBB) for higher-dimensional input variables. This test can be used to check whether a sequence of independent and identically distributed observations belongs to such a parametric family. The approach is based on the empirical residual process introduced by Stute (Ann Statist 25:613-641, 1997). In contrast to Stute and Zhu's approach (2002) Stute \& Zhu (Scandinavian J Statist 29:535-545, 2002), a transformation is not required. Thus, any problems associated with non-parametric regression estimation are avoided. As a result, the MBB method is much easier for users to implement. To illustrate the power of the MBB based tests, a small simulation study is performed. Compared to the approach of Stute \& Zhu (Scandinavian J Statist 29:535-545, 2002), the simulations indicate a slightly improved power of the MBB based method. Finally, both methods are applied to a real data set.},
  language  = {en}
}
@article{GeorgStollenwerkReinkensmeieretal.2021,
  author    = {Georg, J{\"o}rg Heiner and Stollenwerk, Dominik and Reinkensmeier, Sebastian and Jungbluth, Christian},
  title     = {„Smartes" Laden an {\"o}ffentlich zug{\"a}nglichen Lades{\"a}ulen - Teil 1: Quo vadis, Marktdesign?},
  series = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  volume    = {71},
  journal   = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  number    = {1/2},
  publisher = {ETV Energieverlag},
  address   = {Essen},
  isbn      = {0720-6240},
  issn      = {0013-743X},
  pages     = {64 -- 69},
  year      = {2021},
  language  = {de}
}
@article{StollenwerkReinkensmeierGeorgetal.2021,
  author    = {Stollenwerk, Dominik and Reinkensmeier, Sebastian and Georg, J{\"o}rg Heiner and Jungbluth, Christian},
  title     = {„Smartes" Laden an {\"o}ffentlich zug{\"a}nglichen Lades{\"a}ulen - Teil 2: USER-Verhalten und -Erwartungen},
  series = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  volume    = {71},
  journal   = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  number    = {3},
  publisher = {ETV Energieverlag},
  address   = {Essen},
  isbn      = {0720-6240},
  issn      = {0013-743X},
  pages     = {38 -- 42},
  year      = {2021},
  language  = {de}
}
@inproceedings{ElMoussaouiKassmiAlexopoulosetal.2021,
  author    = {El Moussaoui, Noureddine and Kassmi, Khalil and Alexopoulos, Spiros and Schwarzer, Klemens and Chayeb, Hamid and Bachiri, Najib},
  title     = {Simulation studies on a new innovative design of a hybrid solar distiller MSDH alimented with a thermal and photovoltaic energy},
  series = {Materialstoday: Proceedings},
  volume    = {45},
  booktitle = {Materialstoday: Proceedings},
  number    = {8},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2214-7853},
  doi       = {10.1016/j.matpr.2021.03.115},
  pages     = {7653 -- 7660},
  year      = {2021},
  abstract  = {In this paper, we present the structure, the simulation the operation of a multi-stage, hybrid solar desalination system (MSDH), powered by thermal and photovoltaic (PV) (MSDH) energy. The MSDH system consists of a lower basin, eight horizontal stages, a field of four flat thermal collectors with a total area of 8.4 m2, 3 Kw PV panels and solar batteries. During the day the system is heated by thermal energy, and at night by heating resistors, powered by solar batteries. These batteries are charged by the photovoltaic panels during the day. More specifically, during the day and at night, we analyse the temperature of the stages and the production of distilled water according to the solar irradiation intensity and the electric heating power, supplied by the solar batteries. The simulations were carried out in the meteorological conditions of the winter month (February 2020), presenting intensities of irradiance and ambient temperature reaching 824 W/m2 and 23 °C respectively. The results obtained show that during the day the system is heated by the thermal collectors, the temperature of the stages and the quantity of water produced reach 80 °C and 30 Kg respectively. At night, from 6p.m. the system is heated by the electric energy stored in the batteries, the temperature of the stages and the quantity of water produced reach respectively 90 °C and 104 Kg for an electric heating power of 2 Kw. Moreover, when the electric power varies from 1 Kw to 3 Kw the quantity of water produced varies from 92 Kg to 134 Kg. The analysis of these results and their comparison with conventional solar thermal desalination systems shows a clear improvement both in the heating of the stages, by 10\%, and in the quantity of water produced by a factor of 3.},
  language  = {en}
}
@incollection{ButenwegGellertMeyer2021,
  author    = {Butenweg, Christoph and Gellert, Christoph and Meyer, Udo},
  title     = {Erdbebenbemessung bei Mauerwerksbauten},
  series = {Mauerwerk Kalender 2021: Kunststoffverankerungen Digitalisierung im Mauerwerksbau},
  booktitle = {Mauerwerk Kalender 2021: Kunststoffverankerungen Digitalisierung im Mauerwerksbau},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  isbn      = {9783433032930},
  doi       = {10.1002/9783433610732.ch12},
  pages     = {329 -- 355},
  year      = {2021},
  abstract  = {Der vorliegende Beitrag stellt den seismischen Nachweis von Mauerwerksbauten in Deutschland auf Grundlage der DIN EN 1998-1/NA vor, wobei auch die wesentlichen {\"A}nderungen zu der Norm DIN 4149 vergleichend erl{\"a}utert werden. Vorgestellt werden die Definition der Erdbebeneinwirkung, das seismische Verhalten von Mauerwerksbauten und die Erl{\"a}uterung der Rechenverfahren. Darauf aufbauend wird die Anwendung an drei Praxisbeispielen demonstriert.},
  language  = {de}
}
@article{ButenwegKubalskiElDeibetal.2021,
  author    = {Butenweg, Christoph and Kubalski, Thomas and El-Deib, Khaled and Gellert, Christoph},
  title     = {Erdbebennachweis von Mauerwerksbauten nach DIN EN 1998-1/NA-2021},
  series = {Bautechnik : Zeitschrift f{\"u}r den gesamten Ingenieurbau},
  volume    = {98},
  journal   = {Bautechnik : Zeitschrift f{\"u}r den gesamten Ingenieurbau},
  number    = {11},
  editor    = {Jesse, Dirk},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-0999},
  doi       = {10.1002/bate.202100064},
  pages     = {852 -- 863},
  year      = {2021},
  abstract  = {Mauerwerksbauten in Deutschland sind mit Einf{\"u}hrung des nationalen Anwendungsdokuments DIN EN 1998-1/NA auf Grundlage einer neuen probabilistischen Erdbebenkarte nachzuweisen. F{\"u}r erfolgreiche Erdbebennachweise {\"u}blicher Grundrissformen von Mauerwerksbauten stehen in dem zuk{\"u}nftigen Anwendungsdokument neue rechnerische Nachweism{\"o}glichkeiten zur Verf{\"u}gung, mit denen die Tragf{\"a}higkeitsreserven von Mauerwerksbauten in der Baupraxis mit einem {\"u}berschaubaren Aufwand besser in Ansatz gebracht werden k{\"o}nnen. Das Standardrechenverfahren ist weiterhin der kraftbasierte Nachweis, der nun mit h{\"o}heren Verhaltensbeiwerten im Vergleich zur DIN 4149 durchgef{\"u}hrt werden kann. Die h{\"o}heren Verhaltensbeiwerte basieren auf der besseren Ausnutzung der geb{\"a}udespezifischen Verformungsf{\"a}higkeit und Energiedissipation sowie der Lastumverteilung der Schubkr{\"a}fte im Grundriss mit Ansatz von Rahmentragwirkung durch Wand-Deckeninteraktionen. Alternativ dazu kann ein nichtlinearer Nachweis auf Grundlage von Pushover-Analysen zur Anwendung kommen. Vervollst{\"a}ndigt werden die Regelungen f{\"u}r Mauerwerksbauten durch neue Regelungen f{\"u}r nichttragende Innenw{\"a}nde und Außenmauerschalen. Der vorliegende Beitrag stellt die Grundlagen und Hintergr{\"u}nde der neuen rechnerischen Nachweise in DIN EN 1998-1/NA vor und demonstriert deren Anwendung an einem Beispiel aus der Praxis.},
  language  = {de}
}
@inproceedings{Butenweg2021,
  author    = {Butenweg, Christoph},
  title     = {Integrated approach for monitoring and management of buildings with digital building models and modern sensor technologies},
  series = {Proceedings of the International Conference Civil Engineering 2021 - Achievements and Visions},
  booktitle = {Proceedings of the International Conference Civil Engineering 2021 - Achievements and Visions},
  editor    = {Kuzmanović, Vladan and Ignjatović, Ivan},
  publisher = {University of Belgrade},
  address   = {Belgrade},
  pages     = {67 -- 75},
  year      = {2021},
  abstract  = {Nowadays modern high-performance buildings and facilities are equipped with monitoring systems and sensors to control building characteristics like energy consumption, temperature pattern and structural safety. The visualization and interpretation of sensor data is typically based on simple spreadsheets and non-standardized user-oriented solutions, which makes it difficult for building owners, facility managers and decision-makers to evaluate and understand the data. The solution of this problem in the future are integrated BIM-Sensor approaches which allow the generation of BIM models incorporating all relevant information of monitoring systems. These approaches support both the dynamic visualization of key structural performance parameters, the effective long-term management of sensor data based on BIM and provide a user-friendly interface to communicate with various stakeholders. A major benefit for the end user is the use of the BIM software architecture, which is the future standard anyway. In the following, the application of the integrated BIM-Sensor approach is illustrated for a typical industrial facility as a part of an early warning and rapid response system for earthquake events currently developed in the research project "ROBUST" with financial support by the German Federal Ministry for Economic Affairs and Energy (BMWI).},
  language  = {en}
}
@article{ElDeibButenwegKlinkel2021,
  author    = {El-Deib, Khaled and Butenweg, Christoph and Klinkel, Sven},
  title     = {Erdbebennachweis von Mauerwerksbauten mit realistischen Modellen und erh{\"o}hten Verhaltensbeiwerten},
  series = {Mauerwerk},
  volume    = {2021},
  journal   = {Mauerwerk},
  number    = {3},
  editor    = {Jesse, Dirk},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022},
  doi       = {10.1002/dama.202110014},
  pages     = {110 -- 119},
  year      = {2021},
  abstract  = {Die Anwendung des linearen Nachweiskonzepts auf Mauerwerksbauten f{\"u}hrt dazu, dass bereits heute Standsicherheitsnachweise f{\"u}r Geb{\"a}ude mit {\"u}blichen Grundrissen in Gebieten mit moderaten Erdbebeneinwirkungen nicht mehr gef{\"u}hrt werden k{\"o}nnen. Diese Problematik wird sich in Deutschland mit der Einf{\"u}hrung kontinuierlicher probabilistischer Erdbebenkarten weiter versch{\"a}rfen. Aufgrund der Erh{\"o}hung der seismischen Einwirkungen, die sich vielerorts ergibt, ist es erforderlich, die vorhandenen, bislang nicht ber{\"u}cksichtigten Tragf{\"a}higkeitsreserven in nachvollziehbaren Nachweiskonzepten in der Baupraxis verf{\"u}gbar zu machen. Der vorliegende Beitrag stellt ein Konzept f{\"u}r die geb{\"a}udespezifische Ermittlung von erh{\"o}hten Verhaltensbeiwerten vor. Die Verhaltensbeiwerte setzen sich aus drei Anteilen zusammen, mit denen die Lastumverteilung im Grundriss, die Verformungsf{\"a}higkeit und Energiedissipation sowie die {\"U}berfestigkeiten ber{\"u}cksichtigt werden. F{\"u}r die rechnerische Ermittlung dieser drei Anteile wird ein nichtlineares Nachweiskonzept auf Grundlage von Pushover-Analysen vorgeschlagen, in denen die Interaktionen von W{\"a}nden und Geschossdecken durch einen Einspanngrad beschrieben werden. F{\"u}r die Bestimmung der Einspanngrade wird ein nichtlinearer Modellierungsansatz eingef{\"u}hrt, mit dem die Interaktion von W{\"a}nden und Decken abgebildet werden kann. Die Anwendung des Konzepts mit erh{\"o}hten geb{\"a}udespezifischen Verhaltensbeiwerten wird am Beispiel eines Mehrfamilienhauses aus Kalksandsteinen demonstriert. Die Ergebnisse der linearen Nachweise mit erh{\"o}hten Verhaltensbeiwerten f{\"u}r dieses Geb{\"a}ude liegen deutlich n{\"a}her an den Ergebnissen nichtlinearer Nachweise und somit bleiben {\"u}bliche Grundrisse in Erdbebengebieten mit den traditionellen linearen Rechenans{\"a}tzen nachweisbar.},
  language  = {de}
}
@incollection{HoffschmidtAlexopoulosRauetal.2021,
  author    = {Hoffschmidt, Bernhard and Alexopoulos, Spiros and Rau, Christoph and Sattler, Johannes Christoph and Anthrakidis, Anette and Teixeira Boura, Cristiano Jos{\´e} and O'Connor, B. and Chico Caminos, Ricardo Alexander and Rend{\´o}n, C. and Hilger, P.},
  title     = {Concentrating Solar Power},
  series = {Earth systems and environmental sciences},
  booktitle = {Earth systems and environmental sciences},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-0-12-409548-9},
  doi       = {10.1016/B978-0-12-819727-1.00089-3},
  year      = {2021},
  abstract  = {The focus of this chapter is the production of power and the use of the heat produced from concentrated solar thermal power (CSP) systems. The chapter starts with the general theoretical principles of concentrating systems including the description of the concentration ratio, the energy and mass balance. The power conversion systems is the main part where solar-only operation and the increase in operational hours. Solar-only operation include the use of steam turbines, gas turbines, organic Rankine cycles and solar dishes. The operational hours can be increased with hybridization and with storage. Another important topic is the cogeneration where solar cooling, desalination and of heat usage is described. Many examples of commercial CSP power plants as well as research facilities from the past as well as current installed and in operation are described in detail. The chapter closes with economic and environmental aspects and with the future potential of the development of CSP around the world.},
  language  = {en}
}
@article{MarinkovicButenweg2022,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Numerical analysis of the in-plane behaviour of decoupled masonry infilled RC frames},
  series = {Engineering Structures},
  volume    = {272},
  journal   = {Engineering Structures},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0141-0296},
  doi       = {10.1016/j.engstruct.2022.114959},
  pages     = {18 Seiten},
  year      = {2022},
  abstract  = {Damage of reinforced concrete (RC) frames with masonry infill walls has been observed after many earthquakes. Brittle behaviour of the masonry infills in combination with the ductile behaviour of the RC frames makes infill walls prone to damage during earthquakes. Interstory deformations lead to an interaction between the infill and the RC frame, which affects the structural response. The result of this interaction is significant damage to the infill wall and sometimes to the surrounding structural system too. In most design codes, infill walls are considered as non-structural elements and neglected in the design process, because taking into account the infills and considering the interaction between frame and infill in software packages can be complicated and impractical. A good way to avoid negative aspects arising from this behavior is to ensure no or low-interaction of the frame and infill wall, for instance by decoupling the infill from the frame. This paper presents the numerical study performed to investigate new connection system called INODIS (Innovative Decoupled Infill System) for decoupling infill walls from surrounding frame with the aim to postpone infill activation to high interstory drifts thus reducing infill/frame interaction and minimizing damage to both infills and frames. The experimental results are first used for calibration and validation of the numerical model, which is then employed for investigating the influence of the material parameters as well as infill's and frame's geometry on the in-plane behaviour of the infilled frames with the INODIS system. For all the investigated situations, simulation results show significant improvements in behaviour for decoupled infilled RC frames in comparison to the traditionally infilled frames.},
  language  = {en}
}
@inproceedings{MahdiDerschSchmitzetal.2022,
  author    = {Mahdi, Zahra and Dersch, J{\"u}rgen and Schmitz, Pascal and Dieckmann, Simon and Chico Caminos, Ricardo Alexander and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf and Schwager, Christian and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and B{\"u}scher, Rauno},
  title     = {Technical assessment of Brayton cycle heat pumps for the integration in hybrid PV-CSP power plants},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086269},
  pages     = {11 Seiten},
  year      = {2022},
  abstract  = {The hybridization of Concentrated Solar Power (CSP) and Photovoltaics (PV) systems is a promising approach to reduce costs of solar power plants, while increasing dispatchability and flexibility of power generation. High temperature heat pumps (HT HP) can be utilized to boost the salt temperature in the thermal energy storage (TES) of a Parabolic Trough Collector (PTC) system from 385 °C up to 565 °C. A PV field can supply the power for the HT HP, thus effectively storing the PV power as thermal energy. Besides cost-efficiently storing energy from the PV field, the power block efficiency of the overall system is improved due to the higher steam parameters. This paper presents a technical assessment of Brayton cycle heat pumps to be integrated in hybrid PV-CSP power plants. As a first step, a theoretical analysis was carried out to find the most suitable working fluid. The analysis included the fluids Air, Argon (Ar), Nitrogen (N2) and Carbon dioxide (CO2). N2 has been chosen as the optimal working fluid for the system. After the selection of the ideal working medium, different concepts for the arrangement of a HT HP in a PV-CSP hybrid power plant were developed and simulated in EBSILON®Professional. The concepts were evaluated technically by comparing the number of components required, pressure losses and coefficient of performance (COP).},
  language  = {en}
}
@inproceedings{ZahraPhaniSrujanChicoCaminosetal.2022,
  author    = {Zahra, Mahdi and Phani Srujan, Merige and Chico Caminos, Ricardo Alexander and Schmitz, Pascal and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e} and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and Dersch, J{\"u}rgen},
  title     = {Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086268},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica.},
  language  = {en}
}
@article{ButenwegMarinkovicPhlippetal.2022,
  author    = {Butenweg, Christoph and Marinkovic, Marko and Phlipp, Michel and Lins, Robin and Renaut, Philipp},
  title     = {Isolierung und BIM-basiertes Bauwerksmonitoring des neuen Geb{\"a}udekomplexes f{\"u}r das BioSense-Institut in Novi Sad, Serbien},
  series = {Bauingenieur},
  volume    = {97},
  journal   = {Bauingenieur},
  number    = {6},
  editor    = {Haghsheno, Shervin},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {1436-4867},
  doi       = {10.37544/0005-6650-2022-06-28},
  pages     = {S3 -- S5},
  year      = {2022},
  abstract  = {Im Norden von Serbien erfolgt in Novi Sad der Neubau eines modernen Forschungsgeb{\"a}udes f{\"u}r das BioSense-Institut mit finanzieller Unterst{\"u}tzung durch die Eu-rop{\"a}ische Union. Der Geb{\"a}udeteil mit Laboren wird zum Schutz und zur Sicherstellung des reibungslosen Betriebs der sensiblen und kapitalintensiven technischen Einbauten mit ei-ner Erdbebenisolierung mit integrierter K{\"o}rperschallisolation versehen. Zus{\"a}tzlich wird der entkoppelte Laborteil des For-schungsgeb{\"a}udes mit einem BIM-basierten Bauwerksmonito-ring versehen, um {\"A}nderungen des Geb{\"a}udezustands jederzeit abfragen und beurteilen zu k{\"o}nnen.},
  language  = {de}
}
@article{RossiWinandsButenweg2022,
  author    = {Rossi, Leonardo and Winands, Mark H. M. and Butenweg, Christoph},
  title     = {Monte Carlo Tree Search as an intelligent search tool in structural design problems},
  series = {Engineering with Computers : An International Journal for Simulation-Based Engineering},
  volume    = {38},
  journal   = {Engineering with Computers : An International Journal for Simulation-Based Engineering},
  number    = {4},
  editor    = {Zhang, Jessica},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1435-5663},
  doi       = {10.1007/s00366-021-01338-2},
  pages     = {3219 -- 3236},
  year      = {2022},
  abstract  = {Monte Carlo Tree Search (MCTS) is a search technique that in the last decade emerged as a major breakthrough for Artificial Intelligence applications regarding board- and video-games. In 2016, AlphaGo, an MCTS-based software agent, outperformed the human world champion of the board game Go. This game was for long considered almost infeasible for machines, due to its immense search space and the need for a long-term strategy. Since this historical success, MCTS is considered as an effective new approach for many other scientific and technical problems. Interestingly, civil structural engineering, as a discipline, offers many tasks whose solution may benefit from intelligent search and in particular from adopting MCTS as a search tool. In this work, we show how MCTS can be adapted to search for suitable solutions of a structural engineering design problem. The problem consists of choosing the load-bearing elements in a reference reinforced concrete structure, so to achieve a set of specific dynamic characteristics. In the paper, we report the results obtained by applying both a plain and a hybrid version of single-agent MCTS. The hybrid approach consists of an integration of both MCTS and classic Genetic Algorithm (GA), the latter also serving as a term of comparison for the results. The study's outcomes may open new perspectives for the adoption of MCTS as a design tool for civil engineers.},
  language  = {en}
}