@article{MandekarHollandThielenetal.2022,
  author    = {Mandekar, Swati and Holland, Abigail and Thielen, Moritz and Behbahani, Mehdi and Melnykowycz, Mark},
  title     = {Advancing towards Ubiquitous EEG, Correlation of In-Ear EEG with Forehead EEG},
  series = {Sensors},
  volume    = {22},
  journal   = {Sensors},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s22041568},
  pages     = {1 -- 19},
  year      = {2022},
  abstract  = {Wearable EEG has gained popularity in recent years driven by promising uses outside of clinics and research. The ubiquitous application of continuous EEG requires unobtrusive form-factors that are easily acceptable by the end-users. In this progression, wearable EEG systems have been moving from full scalp to forehead and recently to the ear. The aim of this study is to demonstrate that emerging ear-EEG provides similar impedance and signal properties as established forehead EEG. EEG data using eyes-open and closed alpha paradigm were acquired from ten healthy subjects using generic earpieces fitted with three custom-made electrodes and a forehead electrode (at Fpx) after impedance analysis. Inter-subject variability in in-ear electrode impedance ranged from 20 kΩ to 25 kΩ at 10 Hz. Signal quality was comparable with an SNR of 6 for in-ear and 8 for forehead electrodes. Alpha attenuation was significant during the eyes-open condition in all in-ear electrodes, and it followed the structure of power spectral density plots of forehead electrodes, with the Pearson correlation coefficient of 0.92 between in-ear locations ELE (Left Ear Superior) and ERE (Right Ear Superior) and forehead locations, Fp1 and Fp2, respectively. The results indicate that in-ear EEG is an unobtrusive alternative in terms of impedance, signal properties and information content to established forehead EEG.},
  language  = {en}
}
@article{MalinowskiFournierHorbachetal.2022,
  author    = {Malinowski, Daniel and Fournier, Yvan and Horbach, Andreas and Frick, Michael and Magliani, Mirko and Kalverkamp, Sebastian and Hildinger, Martin and Spillner, Jan and Behbahani, Mehdi and Hima, Flutura},
  title     = {Computational fluid dynamics analysis of endoluminal aortic perfusion},
  series = {Perfusion},
  volume    = {0},
  journal   = {Perfusion},
  number    = {0},
  publisher = {Sage},
  address   = {London},
  issn      = {1477-111X},
  doi       = {10.1177/02676591221099809},
  pages     = {1 -- 8},
  year      = {2022},
  abstract  = {Introduction: In peripheral percutaneous (VA) extracorporeal membrane oxygenation (ECMO) procedures the femoral arteries perfusion route has inherent disadvantages regarding poor upper body perfusion due to watershed. With the advent of new long flexible cannulas an advancement of the tip up to the ascending aorta has become feasible. To investigate the impact of such long endoluminal cannulas on upper body perfusion, a Computational Fluid Dynamics (CFD) study was performed considering different support levels and three cannula positions. Methods: An idealized literature-based- and a real patient proximal aortic geometry including an endoluminal cannula were constructed. The blood flow was considered continuous. Oxygen saturation was set to 80\% for the blood coming from the heart and to 100\% for the blood leaving the cannula. 50\% and 90\% venoarterial support levels from the total blood flow rate of 6 l/min were investigated for three different positions of the cannula in the aortic arch. Results: For both geometries, the placement of the cannula in the ascending aorta led to a superior oxygenation of all aortic blood vessels except for the left coronary artery. Cannula placements at the aortic arch and descending aorta could support supra-aortic arteries, but not the coronary arteries. All positions were able to support all branches with saturated blood at 90\% flow volume. Conclusions: In accordance with clinical observations CFD analysis reveals, that retrograde advancement of a long endoluminal cannula can considerably improve the oxygenation of the upper body and lead to oxygen saturation distributions similar to those of a central cannulation.},
  language  = {en}
}
@article{LindnerBurgerRutledgeetal.2022,
  author    = {Lindner, Simon and Burger, Ren{\´e} and Rutledge, Douglas N. and Do, Xuan Tung and Rumpf, Jessica and Diehl, Bernd W. K. and Schulze, Margit and Monakhova, Yulia},
  title     = {Is the calibration transfer of multivariate calibration models between high- and low-field NMR instruments possible? A case study of lignin molecular weight},
  series = {Analytical chemistry},
  volume    = {94},
  journal   = {Analytical chemistry},
  number    = {9},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  isbn      = {1520-6882},
  doi       = {10.1021/acs.analchem.1c05125},
  pages     = {3997 -- 4004},
  year      = {2022},
  abstract  = {Although several successful applications of benchtop nuclear magnetic resonance (NMR) spectroscopy in quantitative mixture analysis exist, the possibility of calibration transfer remains mostly unexplored, especially between high- and low-field NMR. This study investigates for the first time the calibration transfer of partial least squares regressions [weight average molecular weight (Mw) of lignin] between high-field (600 MHz) NMR and benchtop NMR devices (43 and 60 MHz). For the transfer, piecewise direct standardization, calibration transfer based on canonical correlation analysis, and transfer via the extreme learning machine auto-encoder method are employed. Despite the immense resolution difference between high-field and low-field NMR instruments, the results demonstrate that the calibration transfer from high- to low-field is feasible in the case of a physical property, namely, the molecular weight, achieving validation errors close to the original calibration (down to only 1.2 times higher root mean square errors). These results introduce new perspectives for applications of benchtop NMR, in which existing calibrations from expensive high-field instruments can be transferred to cheaper benchtop instruments to economize.},
  language  = {en}
}
@article{LenzKahmannBehbahanietal.2022,
  author    = {Lenz, Maximilian and Kahmann, Stephanie Lucina and Behbahani, Mehdi and Pennig, Lenhard and Hackl, Michael and Leschinger, Tim and M{\"u}ller, Lars Peter and Wegmann, Kilian},
  title     = {Influence of rotator cuff preload on fracture configuration in proximal humerus fractures: a proof of concept for fracture simulation},
  series = {Archives of Orthopaedic and Trauma Surgery},
  journal   = {Archives of Orthopaedic and Trauma Surgery},
  publisher = {Springer},
  address   = {Berlin, Heidelberg},
  issn      = {1434-3916},
  doi       = {10.1007/s00402-022-04471-9},
  year      = {2022},
  abstract  = {Introduction In regard of surgical training, the reproducible simulation of life-like proximal humerus fractures in human cadaveric specimens is desirable. The aim of the present study was to develop a technique that allows simulation of realistic proximal humerus fractures and to analyse the influence of rotator cuff preload on the generated lesions in regards of fracture configuration. Materials and methods Ten cadaveric specimens (6 left, 4 right) were fractured using a custom-made drop-test bench, in two groups. Five specimens were fractured without rotator cuff preload, while the other five were fractured with the tendons of the rotator cuff preloaded with 2 kg each. The humeral shaft and the shortened scapula were potted. The humerus was positioned at 90° of abduction and 10° of internal rotation to simulate a fall on the elevated arm. In two specimens of each group, the emergence of the fractures was documented with high-speed video imaging. Pre-fracture radiographs were taken to evaluate the deltoid-tuberosity index as a measure of bone density. Post-fracture X-rays and CT scans were performed to define the exact fracture configurations. Neer's classification was used to analyse the fractures. Results In all ten cadaveric specimens life-like proximal humerus fractures were achieved. Two III-part and three IV-part fractures resulted in each group. The preloading of the rotator cuff muscles had no further influence on the fracture configuration. High-speed videos of the fracture simulation revealed identical fracture mechanisms for both groups. We observed a two-step fracture mechanism, with initial impaction of the head segment against the glenoid followed by fracturing of the head and the tuberosities and then with further impaction of the shaft against the acromion, which lead to separation of the tuberosities. Conclusion A high energetic axial impulse can reliably induce realistic proximal humerus fractures in cadaveric specimens. The preload of the rotator cuff muscles had no influence on initial fracture configuration. Therefore, fracture simulation in the proximal humerus is less elaborate. Using the presented technique, pre-fractured specimens are available for real-life surgical education.},
  language  = {en}
}
@article{KotliarOrtnerConradietal.2022,
  author    = {Kotliar, Konstantin and Ortner, Marion and Conradi, Anna and Hacker, Patricia and Hauser, Christine and G{\"u}nthner, Roman and Moser, Michaela and Muggenthaler, Claudia and Diehl-Schmid, Janine and Priller, Josef and Schmaderer, Christoph and Grimmer, Timo},
  title     = {Altered retinal cerebral vessel oscillation frequencies in Alzheimer's disease compatible with impaired amyloid clearance},
  series = {Neurobiology of Aging},
  volume    = {120},
  journal   = {Neurobiology of Aging},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0197-4580},
  doi       = {10.1016/j.neurobiolaging.2022.08.012},
  pages     = {117 -- 127},
  year      = {2022},
  abstract  = {Retinal vessels are similar to cerebral vessels in their structure and function. Moderately low oscillation frequencies of around 0.1 Hz have been reported as the driving force for paravascular drainage in gray matter in mice and are known as the frequencies of lymphatic vessels in humans. We aimed to elucidate whether retinal vessel oscillations are altered in Alzheimer's disease (AD) at the stage of dementia or mild cognitive impairment (MCI). Seventeen patients with mild-to-moderate dementia due to AD (ADD); 23 patients with MCI due to AD, and 18 cognitively healthy controls (HC) were examined using Dynamic Retinal Vessel Analyzer. Oscillatory temporal changes of retinal vessel diameters were evaluated using mathematical signal analysis. Especially at moderately low frequencies around 0.1 Hz, arterial oscillations in ADD and MCI significantly prevailed over HC oscillations and correlated with disease severity. The pronounced retinal arterial vasomotion at moderately low frequencies in the ADD and MCI groups would be compatible with the view of a compensatory upregulation of paravascular drainage in AD and strengthen the amyloid clearance hypothesis.},
  language  = {en}
}
@article{KleefeldZimmermann2022,
  author    = {Kleefeld, Andreas and Zimmermann, M.},
  title     = {Computing Elastic Interior Transmission Eigenvalues},
  series = {Integral Methods in Science and Engineering},
  journal   = {Integral Methods in Science and Engineering},
  editor    = {Constanda, Christian and Bodmann, Bardo E.J. and Harris, Paul J.},
  publisher = {Birkh{\"a}user},
  address   = {Cham},
  isbn      = {978-3-031-07171-3},
  doi       = {10.1007/978-3-031-07171-3_10},
  pages     = {139 -- 155},
  year      = {2022},
  abstract  = {An alternative method is presented to numerically compute interior elastic transmission eigenvalues for various domains in two dimensions. This is achieved by discretizing the resulting system of boundary integral equations in combination with a nonlinear eigenvalue solver. Numerical results are given to show that this new approach can provide better results than the finite element method when dealing with general domains.},
  language  = {en}
}
@article{KemptFreyerNagel2022,
  author    = {Kempt, Hendrik and Freyer, Nils and Nagel, Saskia K.},
  title     = {Justice and the normative standards of explainability in healthcare},
  series = {Philosophy \& Technology},
  volume    = {35},
  journal   = {Philosophy \& Technology},
  number    = {Article number: 100},
  publisher = {Springer Nature},
  address   = {Berlin},
  doi       = {10.1007/s13347-022-00598-0},
  pages     = {1 -- 19},
  year      = {2022},
  abstract  = {Providing healthcare services frequently involves cognitively demanding tasks, including diagnoses and analyses as well as complex decisions about treatments and therapy. From a global perspective, ethically significant inequalities exist between regions where the expert knowledge required for these tasks is scarce or abundant. One possible strategy to diminish such inequalities and increase healthcare opportunities in expert-scarce settings is to provide healthcare solutions involving digital technologies that do not necessarily require the presence of a human expert, e.g., in the form of artificial intelligent decision-support systems (AI-DSS). Such algorithmic decision-making, however, is mostly developed in resource- and expert-abundant settings to support healthcare experts in their work. As a practical consequence, the normative standards and requirements for such algorithmic decision-making in healthcare require the technology to be at least as explainable as the decisions made by the experts themselves. The goal of providing healthcare in settings where resources and expertise are scarce might come with a normative pull to lower the normative standards of using digital technologies in order to provide at least some healthcare in the first place. We scrutinize this tendency to lower standards in particular settings from a normative perspective, distinguish between different types of absolute and relative, local and global standards of explainability, and conclude by defending an ambitious and practicable standard of local relative explainability.},
  language  = {en}
}
@article{KaulenSchwabedalSchneideretal.2022,
  author    = {Kaulen, Lars and Schwabedal, Justus T. C. and Schneider, Jules and Ritter, Philipp and Bialonski, Stephan},
  title     = {Advanced sleep spindle identification with neural networks},
  series = {Scientific Reports},
  volume    = {12},
  journal   = {Scientific Reports},
  number    = {Article number: 7686},
  publisher = {Springer Nature},
  address   = {London},
  issn      = {2045-2322},
  doi       = {10.1038/s41598-022-11210-y},
  pages     = {1 -- 10},
  year      = {2022},
  abstract  = {Sleep spindles are neurophysiological phenomena that appear to be linked to memory formation and other functions of the central nervous system, and that can be observed in electroencephalographic recordings (EEG) during sleep. Manually identified spindle annotations in EEG recordings suffer from substantial intra- and inter-rater variability, even if raters have been highly trained, which reduces the reliability of spindle measures as a research and diagnostic tool. The Massive Online Data Annotation (MODA) project has recently addressed this problem by forming a consensus from multiple such rating experts, thus providing a corpus of spindle annotations of enhanced quality. Based on this dataset, we present a U-Net-type deep neural network model to automatically detect sleep spindles. Our model's performance exceeds that of the state-of-the-art detector and of most experts in the MODA dataset. We observed improved detection accuracy in subjects of all ages, including older individuals whose spindles are particularly challenging to detect reliably. Our results underline the potential of automated methods to do repetitive cumbersome tasks with super-human performance.},
  language  = {en}
}
@article{KahmannRauschPluemeretal.2022,
  author    = {Kahmann, Stephanie L. and Rausch, Valentin and Pl{\"u}mer, Jonathan and M{\"u}ller, Lars P. and Pieper, Martin and Wegmann, Kilian},
  title     = {The automized fracture edge detection and generation of three-dimensional fracture probability heat maps},
  series = {Medical Engineering \& Physics},
  volume    = {2022},
  journal   = {Medical Engineering \& Physics},
  number    = {110},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1350-4533},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1-2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further.},
  language  = {en}
}
@article{HoffmannUhlCeblinetal.2022,
  author    = {Hoffmann, Andreas and Uhl, Matthias and Ceblin, Maximilian and Rohrbach, Felix and Bansmann, Joachim and Mallah, Marcel and Heuermann, Holger and Jacob, Timo and Kuehne, Alexander J.C.},
  title     = {Atmospheric pressure plasma-jet treatment of PAN-nonwovens—carbonization of nanofiber electrodes},
  series = {C - Journal of Carbon Research},
  volume    = {8},
  journal   = {C - Journal of Carbon Research},
  number    = {3},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2311-5629},
  doi       = {10.3390/c8030033},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {Carbon nanofibers are produced from dielectric polymer precursors such as polyacrylonitrile (PAN). Carbonized nanofiber nonwovens show high surface area and good electrical conductivity, rendering these fiber materials interesting for application as electrodes in batteries, fuel cells, and supercapacitors. However, thermal processing is slow and costly, which is why new processing techniques have been explored for carbon fiber tows. Alternatives for the conversion of PAN-precursors into carbon fiber nonwovens are scarce. Here, we utilize an atmospheric pressure plasma jet to conduct carbonization of stabilized PAN nanofiber nonwovens. We explore the influence of various processing parameters on the conductivity and degree of carbonization of the converted nanofiber material. The precursor fibers are converted by plasma-jet treatment to carbon fiber nonwovens within seconds, by which they develop a rough surface making subsequent surface activation processes obsolete. The resulting carbon nanofiber nonwovens are applied as supercapacitor electrodes and examined by cyclic voltammetry and impedance spectroscopy. Nonwovens that are carbonized within 60 s show capacitances of up to 5 F g⁻¹.},
  language  = {en}
}
@article{HoffmannRohrbachUhletal.2022,
  author    = {Hoffmann, Andreas and Rohrbach, Felix and Uhl, Matthias and Ceblin, Maximilian and Bauer, Thomas and Mallah, Marcel and Jacob, Timo and Heuermann, Holger and Kuehne, Alexander J. C.},
  title     = {Atmospheric pressure plasma-jet treatment of polyacrylonitrile-nonwovens—Stabilization and roll-to-roll processing},
  series = {Journal of Applied Polymer Science},
  volume    = {139},
  journal   = {Journal of Applied Polymer Science},
  number    = {37},
  publisher = {Wiley},
  issn      = {0021-8995 (Print)},
  doi       = {10.1002/app.52887},
  pages     = {1 -- 9},
  year      = {2022},
  abstract  = {Carbon nanofiber nonwovens represent a powerful class of materials with prospective application in filtration technology or as electrodes with high surface area in batteries, fuel cells, and supercapacitors. While new precursor-to-carbon conversion processes have been explored to overcome productivity restrictions for carbon fiber tows, alternatives for the two-step thermal conversion of polyacrylonitrile precursors into carbon fiber nonwovens are absent. In this work, we develop a continuous roll-to-roll stabilization process using an atmospheric pressure microwave plasma jet. We explore the influence of various plasma-jet parameters on the morphology of the nonwoven and compare the stabilized nonwoven to thermally stabilized samples using scanning electron microscopy, differential scanning calorimetry, and infrared spectroscopy. We show that stabilization with a non-equilibrium plasma-jet can be twice as productive as the conventional thermal stabilization in a convection furnace, while producing electrodes of comparable electrochemical performance.},
  language  = {en}
}
@article{HeuermannEmmrichBongartz2022,
  author    = {Heuermann, Holger and Emmrich, Thomas and Bongartz, Simon},
  title     = {Microwave spark plug to support ignitions with high compression ratios},
  series = {IEEE Transactions on Plasma Science},
  journal   = {IEEE Transactions on Plasma Science},
  number    = {Early Access},
  publisher = {IEEE},
  issn      = {1939-9375},
  doi       = {10.1109/TPS.2022.3183690},
  pages     = {1 -- 6},
  year      = {2022},
  abstract  = {Upcoming gasoline engines should run with a larger number of fuels beginning from petrol over methanol up to gas by a wide range of compression ratios and a homogeneous charge. In this article, the microwave (MW) spark plug, based on a high-speed frequency hopping system, is introduced as a solution, which can support a nitrogen compression ratio up to 1:39 in a chamber and more. First, an overview of the high-speed frequency hopping MW ignition and operation system as well as the large number of applications are presented. Both gives an understanding of this new base technology for MW plasma generation. Focus of the theoretical part is the explanation of the internal construction of the spark plug, on the achievable of the high voltage generation as well as the high efficiency to hold the plasma. In detail, the development process starting with circuit simulations and ending with the numerical multiphysics field simulations is described. The concept is evaluated with a reference prototype covering the frequency range between 2.40 and 2.48 GHz and working over a large power range from 20 to 200 W. A larger number of different measurements starting by vector hot-S11 measurements and ending by combined working scenarios out of hot temperature, high pressure and charge motion are winding up the article. The limits for the successful pressure tests were given by the pressure chamber. Pressures ranged from 1 to 39 bar and charge motion up to 25 m/s as well as temperatures from 30◦ to 125◦.},
  language  = {en}
}
@article{HerssensCowburnAlbrachtetal.2022,
  author    = {Herssens, Nolan and Cowburn, James and Albracht, Kirsten and Braunstein, Bjoern and Cazzola, Dario and Colyer, Steffi and Minetti, Alberto E. and Pavei, Gaspare and Rittweger, J{\"o}rn and Weber, Tobias and Green, David A.},
  title     = {Movement in low gravity environments (MoLo) programme - the MoLo-L.O.O.P. study protocol},
  series = {PLOS ONE / Public Library of Science},
  volume    = {17},
  journal   = {PLOS ONE / Public Library of Science},
  number    = {11},
  editor    = {Cattaneo, Luigi},
  publisher = {Plos},
  address   = {San Francisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0278051},
  pages     = {e0278051},
  year      = {2022},
  abstract  = {Exposure to prolonged periods in microgravity is associated with deconditioning of the musculoskeletal system due to chronic changes in mechanical stimulation. Given astronauts will operate on the Lunar surface for extended periods of time, it is critical to quantify both external (e.g., ground reaction forces) and internal (e.g., joint reaction forces) loads of relevant movements performed during Lunar missions. Such knowledge is key to predict musculoskeletal deconditioning and determine appropriate exercise countermeasures associated with extended exposure to hypogravity.},
  language  = {en}
}
@article{HeinEubanksLingametal.2022,
  author    = {Hein, Andreas M. and Eubanks, T. Marshall and Lingam, Manasvi and Hibberd, Adam and Fries, Dan and Schneider, Jean and Kervella, Pierre and Kennedy, Robert and Perakis, Nikolaos and Dachwald, Bernd},
  title     = {Interstellar now! Missions to explore nearby interstellar objects},
  series = {Advances in Space Research},
  volume    = {69},
  journal   = {Advances in Space Research},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  doi       = {10.1016/j.asr.2021.06.052},
  pages     = {402 -- 414},
  year      = {2022},
  abstract  = {The recently discovered first hyperbolic objects passing through the Solar System, 1I/'Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system.},
  language  = {en}
}
@article{HarrisKleefeld2022,
  author    = {Harris, Isaac and Kleefeld, Andreas},
  title     = {Analysis and computation of the transmission eigenvalues with a conductive boundary condition},
  series = {Applicable Analysis},
  volume    = {101},
  journal   = {Applicable Analysis},
  number    = {6},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1563-504X},
  doi       = {10.1080/00036811.2020.1789598},
  pages     = {1880 -- 1895},
  year      = {2022},
  abstract  = {We provide a new analytical and computational study of the transmission eigenvalues with a conductive boundary condition. These eigenvalues are derived from the scalar inverse scattering problem for an inhomogeneous material with a conductive boundary condition. The goal is to study how these eigenvalues depend on the material parameters in order to estimate the refractive index. The analytical questions we study are: deriving Faber-Krahn type lower bounds, the discreteness and limiting behavior of the transmission eigenvalues as the conductivity tends to infinity for a sign changing contrast. We also provide a numerical study of a new boundary integral equation for computing the eigenvalues. Lastly, using the limiting behavior we will numerically estimate the refractive index from the eigenvalues provided the conductivity is sufficiently large but unknown.},
  language  = {en}
}
@article{HaegerBongaertsSiegert2022,
  author    = {Haeger, Gerrit and Bongaerts, Johannes and Siegert, Petra},
  title     = {A convenient ninhydrin assay in 96-well format for amino acid-releasing enzymes using an air-stable reagent},
  series = {Analytical Biochemistry},
  journal   = {Analytical Biochemistry},
  number    = {624},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1096-0309},
  doi       = {10.1016/j.ab.2022.114819},
  pages     = {Artikel 114819},
  year      = {2022},
  abstract  = {An improved and convenient ninhydrin assay for aminoacylase activity measurements was developed using the commercial EZ Nin™ reagent. Alternative reagents from literature were also evaluated and compared. The addition of DMSO to the reagent enhanced the solubility of Ruhemann's purple (RP). Furthermore, we found that the use of a basic, aqueous buffer enhances stability of RP. An acidic protocol for the quantification of lysine was developed by addition of glacial acetic acid. The assay allows for parallel processing in a 96-well format with measurements microtiter plates.},
  language  = {en}
}
@article{GaigallGerstenbergTrinh2022,
  author    = {Gaigall, Daniel and Gerstenberg, Julian and Trinh, Thi Thu Ha},
  title     = {Empirical process of concomitants for partly categorial data and applications in statistics},
  series = {Bernoulli},
  volume    = {28},
  journal   = {Bernoulli},
  number    = {2},
  publisher = {International Statistical Institute},
  address   = {Den Haag, NL},
  issn      = {1573-9759},
  doi       = {10.3150/21-BEJ1367},
  pages     = {803 -- 829},
  year      = {2022},
  abstract  = {On the basis of independent and identically distributed bivariate random vectors, where the components are categorial and continuous variables, respectively, the related concomitants, also called induced order statistic, are considered. The main theoretical result is a functional central limit theorem for the empirical process of the concomitants in a triangular array setting. A natural application is hypothesis testing. An independence test and a two-sample test are investigated in detail. The fairly general setting enables limit results under local alternatives and bootstrap samples. For the comparison with existing tests from the literature simulation studies are conducted. The empirical results obtained confirm the theoretical findings.},
  language  = {en}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Powertrain Adaptions for LPG Usage in General Aviation},
  series = {MTZ worldwide},
  volume    = {2022},
  journal   = {MTZ worldwide},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s38313-021-0756-6},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {In general aviation, too, it is desirable to be able to operate existing internal combustion engines with fuels that produce less CO₂ than Avgas 100LL being widely used today It can be assumed that, in comparison, the fuels CNG, LPG or LNG, which are gaseous under normal conditions, produce significantly lower emissions. Necessary propulsion system adaptations were investigated as part of a research project at Aachen University of Applied Sciences.},
  language  = {en}
}
@article{FunkeBeckmann2022,
  author    = {Funke, Harald and Beckmann, Nils},
  title     = {Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture},
  series = {International Journal of Gas Turbine, Propulsion and Power Systems},
  volume    = {13},
  journal   = {International Journal of Gas Turbine, Propulsion and Power Systems},
  number    = {2},
  issn      = {1882-5079},
  pages     = {1 -- 7},
  year      = {2022},
  abstract  = {The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.\% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance},
  language  = {en}
}
@article{FiedlerOrzadaFloeseretal.2022,
  author    = {Fiedler, Thomas M. and Orzada, Stephan and Fl{\"o}ser, Martina and Rietsch, Stefan H. G. and Schmidt, Simon and Stelter, Jonathan K. and Wittrich, Marco and Quick, Harald H. and Bitz, Andreas and Ladd, Mark E.},
  title     = {Performance and safety assessment of an integrated transmit array for body imaging at 7 T under consideration of specificabsorption rate, tissue temperature, and thermal dose},
  series = {NMR in Biomedicine},
  volume    = {35},
  journal   = {NMR in Biomedicine},
  number    = {5},
  publisher = {Wiley},
  issn      = {0952-3480 (Print)},
  doi       = {10.1002/nbm.4656},
  pages     = {1 -- 17},
  year      = {2022},
  abstract  = {In this study, the performance of an integrated body-imaging array for 7 T with 32 radiofrequency (RF) channels under consideration of local specific absorption rate (SAR), tissue temperature, and thermal dose limits was evaluated and the imaging performance was compared with a clinical 3 T body coil. Thirty-two transmit elements were placed in three rings between the bore liner and RF shield of the gradient coil. Slice-selective RF pulse optimizations for B1 shimming and spokes were performed for differently oriented slices in the body under consideration of realistic constraints for power and local SAR. To improve the B1+ homogeneity, safety assessments based on temperature and thermal dose were performed to possibly allow for higher input power for the pulse optimization than permissible with SAR limits. The results showed that using two spokes, the 7 T array outperformed the 3 T birdcage in all the considered regions of interest. However, a significantly higher SAR or lower duty cycle at 7 T is necessary in some cases to achieve similar B1+ homogeneity as at 3 T. The homogeneity in up to 50 cm-long coronal slices can particularly benefit from the high RF shim performance provided by the 32 RF channels. The thermal dose approach increases the allowable input power and the corresponding local SAR, in one example up to 100 W/kg, without limiting the exposure time necessary for an MR examination. In conclusion, the integrated antenna array at 7 T enables a clinical workflow for body imaging and comparable imaging performance to a conventional 3 T clinical body coil.},
  language  = {en}
}