@article{CheenakulaGriebelMontagetal.2023,
  author    = {Cheenakula, Dheeraja and Griebel, Kai and Montag, David and Gr{\"o}mping, Markus},
  title     = {Concept development of a mainstream deammonification and comparison with conventional process in terms of energy, performance and economical construction perspectives},
  series = {Frontiers in Microbiology},
  volume    = {14},
  journal   = {Frontiers in Microbiology},
  number    = {11155235},
  editor    = {Huang, Xiaowu},
  publisher = {Frontiers},
  issn      = {1664-302X},
  doi       = {10.3389/fmicb.2023.1155235},
  pages     = {1 -- 15},
  year      = {2023},
  abstract  = {Deammonification for nitrogen removal in municipal wastewater in temperate and cold climate zones is currently limited to the side stream of municipal wastewater treatment plants (MWWTP). This study developed a conceptual model of a mainstream deammonification plant, designed for 30,000 P.E., considering possible solutions corresponding to the challenging mainstream conditions in Germany. In addition, the energy-saving potential, nitrogen elimination performance and construction-related costs of mainstream deammonification were compared to a conventional plant model, having a single-stage activated sludge process with upstream denitrification. The results revealed that an additional treatment step by combining chemical precipitation and ultra-fine screening is advantageous prior the mainstream deammonification. Hereby chemical oxygen demand (COD) can be reduced by 80\% so that the COD:N ratio can be reduced from 12 to 2.5. Laboratory experiments testing mainstream conditions of temperature (8-20°C), pH (6-9) and COD:N ratio (1-6) showed an achievable volumetric nitrogen removal rate (VNRR) of at least 50 gN/(m3∙d) for various deammonifying sludges from side stream deammonification systems in the state of North Rhine-Westphalia, Germany, where m3 denotes reactor volume. Assuming a retained Norganic content of 0.0035 kgNorg./(P.E.∙d) from the daily loads of N at carbon removal stage and a VNRR of 50 gN/(m3∙d) under mainstream conditions, a resident-specific reactor volume of 0.115 m3/(P.E.) is required for mainstream deammonification. This is in the same order of magnitude as the conventional activated sludge process, i.e., 0.173 m3/(P.E.) for an MWWTP of size class of 4. The conventional plant model yielded a total specific electricity demand of 35 kWh/(P.E.∙a) for the operation of the whole MWWTP and an energy recovery potential of 15.8 kWh/(P.E.∙a) through anaerobic digestion. In contrast, the developed mainstream deammonification model plant would require only a 21.5 kWh/(P.E.∙a) energy demand and result in 24 kWh/(P.E.∙a) energy recovery potential, enabling the mainstream deammonification model plant to be self-sufficient. The retrofitting costs for the implementation of mainstream deammonification in existing conventional MWWTPs are nearly negligible as the existing units like activated sludge reactors, aerators and monitoring technology are reusable. However, the mainstream deammonification must meet the performance requirement of VNRR of about 50 gN/(m3∙d) in this case.},
  language  = {en}
}
@article{BienerSasse1993,
  author    = {Biener, Ernst and Sasse, T.},
  title     = {Construction and rehabilitation of landfill shafts},
  series = {Sardinia 93 : Fourth International Landfill Symposium "Barrier systems, environmental aspects, upgrading and remediation, siting, monofills, effects of waste pretreatment, landfilling in developing countries" ; 11 - 15 October 1993, S. Margherita di Pula (Cagliari), Sardinia, Italy ; proceedings / coord. by Thomas H. Christensen ... - Bd. 1},
  journal   = {Sardinia 93 : Fourth International Landfill Symposium "Barrier systems, environmental aspects, upgrading and remediation, siting, monofills, effects of waste pretreatment, landfilling in developing countries" ; 11 - 15 October 1993, S. Margherita di Pula (Cagliari), Sardinia, Italy ; proceedings / coord. by Thomas H. Christensen ... - Bd. 1},
  publisher = {CISA, Environmental Sanitary Engineering Centre},
  address   = {Cagliari},
  pages     = {451 -- 460},
  year      = {1993},
  language  = {en}
}
@article{BienerSasse1994,
  author    = {Biener, Ernst and Sasse, T.},
  title     = {Construction of composite lining systems under unfavourable weather conditions},
  series = {Landfilling of waste: barriers / ed. by T. H. Christensen; R. Cossu; R. Stegmann. - 1. Aufl.},
  journal   = {Landfilling of waste: barriers / ed. by T. H. Christensen; R. Cossu; R. Stegmann. - 1. Aufl.},
  publisher = {Spon},
  address   = {London [u.a.]},
  isbn      = {0419159908},
  pages     = {183 -- 200},
  year      = {1994},
  language  = {en}
}
@article{WoliszSchuetzBlankeetal.2017,
  author    = {Wolisz, Henryk and Sch{\"u}tz, Thomas and Blanke, Tobias and Hagenkamp, Markus and Kohrn, Markus and Wesseling, Mark and M{\"u}ller, Dirk},
  title     = {Cost optimal sizing of smart buildings' energy system components considering changing end-consumer electricity markets},
  series = {Energy},
  volume    = {137},
  journal   = {Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.1016/j.energy.2017.06.025},
  pages     = {715 -- 728},
  year      = {2017},
  language  = {en}
}
@inproceedings{JockwerKleiberUibel2018,
  author    = {Jockwer, R. and Kleiber, M. and Uibel, Thomas},
  title     = {Criteria for Evaluating the Simplification of Design Rules for Dowel-type Fasteners},
  series = {International Network on Timber Engineering Research, INTER : proceedings, meeting 51, 10 - 13 August 2016, Tallinn, Estonia},
  booktitle = {International Network on Timber Engineering Research, INTER : proceedings, meeting 51, 10 - 13 August 2016, Tallinn, Estonia},
  editor    = {G{\"o}rlacher, Rainer},
  publisher = {Timber Scientific Publishing, KIT Holzbau und Baukonstruktionen},
  address   = {Karlsruhe},
  pages     = {461 -- 466},
  year      = {2018},
  language  = {en}
}
@article{Bung2011,
  author    = {Bung, Daniel B.},
  title     = {Developing flow in skimming flow regime on embankment stepped spillways},
  series = {Journal of hydraulic research},
  volume    = {Vol. 49},
  journal   = {Journal of hydraulic research},
  number    = {Iss. 5},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1814-2079 (E-Journal); 0022-1686 (Print)},
  pages     = {639 -- 648},
  year      = {2011},
  language  = {en}
}
@misc{SchulzeBuxlohGrossCheng2020,
  author    = {Schulze-Buxloh, Lina and Groß, Rolf Fritz and Cheng, Kevin Toni},
  title     = {Development and manufacturing of an interactive three-dimensional phase diagram of carbon dioxide for teaching sessions in thermodynamics},
  series = {Proceedings of the International Conference The Future of Education 2020},
  journal   = {Proceedings of the International Conference The Future of Education 2020},
  year      = {2020},
  language  = {en}
}
@article{ValeroBung2016,
  author    = {Valero, Daniel and Bung, Daniel B.},
  title     = {Development of the interfacial air layer in the non-aerated region of high-velocity spillway flows: Instabilities growth, entrapped air and influence on the self-aeration onset},
  series = {International Journal of Multiphase Flow},
  volume    = {84},
  journal   = {International Journal of Multiphase Flow},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0301-9322},
  doi       = {10.1016/j.ijmultiphaseflow.2016.04.012},
  pages     = {66 -- 74},
  year      = {2016},
  abstract  = {Self-aeration is traditionally explained by the water turbulent boundary layer outer edge intersection with the free surface. This paper presents a discussion on the commonly accepted hypothesis behind the computation of the critical point of self-aeration in spillway flows and a new formulation is proposed based on the existence of a developing air flow over the free surface. Upstream of the inception point of self-aeration, some surface roughening has been often reported in previous studies which consequently implies some entrapped air transport and air-water flows coupling. Such air flow is proven in this study by presenting measured air velocities and computing the air boundary layer thickness for a 1V:2H smooth chute flow. Additionally, the growth rate of free surface waves has been analysed by means of Ultrasonic Sensors measurements, obtaining also the entrapped air concentration. High-speed camera imaging has been used for qualitative study of the flow perturbations.},
  language  = {en}
}
@inproceedings{SchulzeBuxlohGrossUlbrich2021,
  author    = {Schulze-Buxloh, Lina and Groß, Rolf Fritz and Ulbrich, Michelle},
  title     = {Digital planning using building information modelling and virtual reality: new approach for students' remote practical training under lockdown conditions in the course of smart building engineering},
  series = {Proceedings of International Conference on Education in Mathematics, Science and Technology 2021},
  booktitle = {Proceedings of International Conference on Education in Mathematics, Science and Technology 2021},
  publisher = {ISTES Organization},
  address   = {San Antonio, TX},
  isbn      = {978-1-952092-17-6},
  pages     = {118 -- 123},
  year      = {2021},
  abstract  = {The worldwide Corona pandemic has severely restricted student projects in the higher semesters of engineering courses. In order not to delay the graduation, a new concept had to be developed for projects under lockdown conditions. Therefore, unused rooms at the university should be digitally recorded in order to develop a new usage concept as laboratory rooms. An inventory of the actual state of the rooms was done first by taking photos and listing up all flaws and peculiarities. After that, a digital site measuring was done with a 360° laser scanner and these recorded scans were linked to a coherent point cloud and transferred to a software for planning technical building services and supporting Building Information Modelling (BIM). In order to better illustrate the difference between the actual and target state, two virtual reality models were created for realistic demonstration. During the project, the students had to go through the entire digital planning phases. Technical specifications had to be complied with, as well as documentation, time planning and cost estimate. This project turned out to be an excellent alternative to on-site practical training under lockdown conditions and increased the students' motivation to deal with complex technical questions.},
  language  = {en}
}
@techreport{KestiBurstrandKnutssonSalvatoreetal.2008,
  author    = {Kesti, J. and Burstrand Knutsson, H. and Salvatore, W. and Saouridis, C. and Odrieres Mer{\´e}, J. and Georgi, H. and Casajus, A. and Butz, C. and Schneider, R. and D{\"o}ring, Bernd},
  title     = {Dissemination of knowledge in the use of steel-intensive dry construction systems in housing : final report. Contract No RFS2-CT-2004-00036. EUR 22849 EN},
  publisher = {Office for Official Publications of the European Communities},
  address   = {Luxembourg},
  organization    = {European Commission / Research Fund for Coal and Steel},
  isbn      = {978-92-79-05973-5},
  pages     = {205 S.},
  year      = {2008},
  language  = {en}
}
@inproceedings{StepkesZimmermannMuelleretal.2007,
  author    = {Stepkes, Hermann and Zimmermann, J. and M{\"u}ller, Karsten and Siekmann, Marko and Pinnekamp, Josef},
  title     = {Economical rehabilitation of sewer systems by ground penetration radar investigations},
  series = {Strategic asset management of water supply and wastewater infrastructures : invited papers from the 2nd IWA Leading Edge Conference on Strategic Asset Management (LESAM), Lisbon, October [17 - 19] 2007 / ed. by Helene Alegre and Maria do C{\´e}u Almeida},
  booktitle = {Strategic asset management of water supply and wastewater infrastructures : invited papers from the 2nd IWA Leading Edge Conference on Strategic Asset Management (LESAM), Lisbon, October [17 - 19] 2007 / ed. by Helene Alegre and Maria do C{\´e}u Almeida},
  publisher = {IWA Publ.},
  address   = {London},
  isbn      = {9781843391869},
  pages     = {501 -- 520},
  year      = {2007},
  language  = {en}
}
@inproceedings{UibelBlass2007,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {Edge Joints with Dowel Type Fasteners in Cross Laminated Timber},
  series = {Proceedings. CIB-W18 Meeting 2007, Bled, Slovenia 2007},
  booktitle = {Proceedings. CIB-W18 Meeting 2007, Bled, Slovenia 2007},
  issn      = {0945-6996},
  pages     = {1 -- 11},
  year      = {2007},
  language  = {en}
}
@techreport{FeldmannKuhnhenneDoeringetal.2013,
  author    = {Feldmann, M. and Kuhnhenne, M. and D{\"o}ring, Bernd and Pyschny, D. and Lawson, R.M. and Chuter, R.D. and Boudjabeur, S. and Lecomte-Labory, F. and Airaksinen, M. and Heikkinen, J. and Laamanen, J. and Albart, P. and D'Haeyer, R. and Chica, J.A. and Maseda, J.M. and Amundarain, A. and Rips, M.O. and Nu{\~n}ez, J.A. and Mac{\´i}as, O. and Beguin, P. and Ben Larbi, A.},
  title     = {Energy and thermal improvements for construction in steel (ETHICS) - EUR 26010},
  publisher = {Publications Office of the European Union},
  address   = {Luxembourg},
  organization    = {European Commission},
  isbn      = {978-92-79-30789-8},
  issn      = {1831-9424},
  doi       = {10.2777/17106},
  pages     = {136 Seiten},
  year      = {2013},
  abstract  = {ETHICS is concerned with evaluating, measuring and making improvements in the thermal and energy performance of steel-clad and steel-framed buildings. It addresses basic building physics performance at a laboratory and full-scale level, and the preparation of design guidance for commercial, industrial and residential buildings. It includes the development of design tools to assist users in assessing whole-building performance, and calibrates these tools against whole-building measurements, which will be obtained from this research. Opportunities for renewable energy and other energy-saving features will be assessed. This project focuses on objectives that are of particular interest for the design of new steel constructions regarding energy efficiency. ETHICS investigates the as-built performance by on-site tests regarding air tightness and heat transfer properties of the building envelope and by monitoring the energy consumption and thermal comfort of selected up-to-date steel buildings. As energy efficiency is a key requirement for design and construction of buildings in the future, this project provides well-founded scientific data, which prove the high energy performance of current steel constructions and work out details for further improvements to maintain and extend the position of steel products in the construction sector.},
  language  = {en}
}
@article{ValeroBungCrookston2018,
  author    = {Valero, Daniel and Bung, Daniel B. and Crookston, B.M.},
  title     = {Energy dissipation of a Type III basin under design and adverse conditions for stepped and smooth spillways},
  series = {Journal of Hydraulic Engineering},
  volume    = {144},
  journal   = {Journal of Hydraulic Engineering},
  number    = {7},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {0733-9429},
  doi       = {10.1061/(ASCE)HY.1943-7900.0001482},
  year      = {2018},
  abstract  = {New information regarding the influence of a stepped chute on the hydraulic performance of the United States Bureau of Reclamation (Reclamation) Type III hydraulic jump stilling basin is presented for design (steady) and adverse (decreasing tailwater) conditions. Using published experimental data and computational fluid dynamics (CFD) models, this paper presents a detailed comparison between smooth-chute and stepped-chute configurations for chute slopes of 0.8H:1V and 4H:1V and Froude numbers (F) ranging from 3.1 to 9.5 for a Type III basin designed for F = 8. For both stepped and smooth chutes, the relative role of each basin element was quantified, up to the most hydraulic extreme case of jump sweep-out. It was found that, relative to a smooth chute, the turbulence generated by a stepped chute causes a higher maximum velocity decay within the stilling basin, which represents an enhancement of the Type III basin's performance but also a change in the relative role of the basin elements. Results provide insight into the ability of the CFD models [unsteady Reynolds-averaged Navier-Stokes (RANS) equations with renormalization group (RNG) k-ϵ turbulence model and volume-of-fluid (VOF) for free surface tracking] to predict the transient basin flow structure and velocity profiles. Type III basins can perform adequately with a stepped chute despite the effects steps have on the relative role of each basin element. It is concluded that the classic Type III basin design, based upon methodology by reclamation specific to smooth chutes, can be hydraulically improved for the case of stepped chutes for design and adverse flow conditions using the information presented herein.},
  language  = {en}
}
@inproceedings{KerpenBungValeroetal.2016,
  author    = {Kerpen, Nils B. and Bung, Daniel B. and Valero, Daniel and Schlurmann, Torsten},
  title     = {Energy dissipation within the wave run-up at stepped revetments},
  series = {8th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering, Qingdao, China},
  booktitle = {8th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering, Qingdao, China},
  pages     = {6 Seiten},
  year      = {2016},
  language  = {en}
}
@article{KerpenBungValeroetal.2017,
  author    = {Kerpen, Nils B. and Bung, Daniel B. and Valero, Daniel and Schlurmann, Torsten},
  title     = {Energy dissipation within the wave run-up at stepped revetments},
  series = {Journal of Ocean University of China},
  volume    = {16},
  journal   = {Journal of Ocean University of China},
  number    = {4},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1993-5021},
  doi       = {10.1007/s11802-017-3355-z},
  pages     = {649 -- 654},
  year      = {2017},
  language  = {en}
}
@inproceedings{KuhnhenneDoeringPyschnyetal.2012,
  author    = {Kuhnhenne, Markus and D{\"o}ring, Bernd and Pyschny, Dominik and Feldmann, Markus},
  title     = {Energy efficient sandwich construction},
  series = {Proceedings of the VI International Congress on Architectural Envelopes : 20.6. - 22.6.2012, San Sebastian, Spain},
  booktitle = {Proceedings of the VI International Congress on Architectural Envelopes : 20.6. - 22.6.2012, San Sebastian, Spain},
  publisher = {ICAE},
  organization    = {International Congress on Architectural Envelopes <6, 2012, San Sebastian>},
  pages     = {277 -- 285},
  year      = {2012},
  language  = {en}
}
@article{BienerSasse1988,
  author    = {Biener, Ernst and Sasse, T.},
  title     = {Experience with new techniques in slurry cutoff wall construction},
  series = {ISWA 88, proceedings of the 5th International Solid Wastes Conference : September 11 - 16th, 1988, Copenhagen, Denmark / ed. by Lizzi Andersen ... - Vol. 1 : Oral presentations},
  journal   = {ISWA 88, proceedings of the 5th International Solid Wastes Conference : September 11 - 16th, 1988, Copenhagen, Denmark / ed. by Lizzi Andersen ... - Vol. 1 : Oral presentations},
  publisher = {Acad. Press},
  address   = {London [u.a.]},
  isbn      = {0-12-058451-4},
  pages     = {41 -- 46},
  year      = {1988},
  language  = {en}
}
@inproceedings{GogolinCarvalhoBungetal.2013,
  author    = {Gogolin, C. and Carvalho, R. and Bung, Daniel B. and Matos, J.},
  title     = {Experimental and numerical investigation of steady and unsteady flows in roughened channels with cross beams},
  series = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China},
  booktitle = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China},
  publisher = {Tsinghua Univ. Press},
  address   = {Beijing},
  organization    = {International Association for Hydraulic Engineering and Research},
  pages     = {Artikelkennnummer: A10837C},
  year      = {2013},
  language  = {en}
}
@inproceedings{Kirsch2009,
  author    = {Kirsch, Ansgar},
  title     = {Experimental and numerical investigation of the face stability of shallow tunnels in sand},
  series = {Safe tunnelling for the city and environment : proceedings of the World Tunnel Congress 2009, Budapest, Hungary, 23 to 28 September 2009 / organised by International Tunnelling and Underground Space Association ...},
  booktitle = {Safe tunnelling for the city and environment : proceedings of the World Tunnel Congress 2009, Budapest, Hungary, 23 to 28 September 2009 / organised by International Tunnelling and Underground Space Association ...},
  publisher = {Hungarian Tunnelling Association},
  address   = {Budapest},
  organization    = {World Tunnel Congress <2009, Budapest>},
  pages     = {1 -- 8},
  year      = {2009},
  language  = {en}
}