@inproceedings{LuBeyerBosiljkovetal.2016,
  author    = {Lu, S. and Beyer, K. and Bosiljkov, V. and Butenweg, Christoph and D'Ayala, D. and Degee, H. and Gams, M. and Klouda, J. and Lagomarsino, S. and Penna, A. and Mojsilovic, N. and da Porto, F. and Sorrentino, L. and Vintzileou, E.},
  title     = {Next generation of Eurocode 8, masonry chapter},
  series = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  booktitle = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  editor    = {Modena, Claudio and da Porto, F. and Valluzzi, M.R.},
  publisher = {Taylor \& Francis},
  address   = {London},
  isbn      = {978-1-138-02999-6 (Print)},
  pages     = {695 -- 700},
  year      = {2016},
  abstract  = {This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date.},
  language  = {en}
}
@inproceedings{Mertens2001,
  author    = {Mertens, Josef},
  title     = {Next steps envisaged to improve wing performance of commercial aircraft},
  series = {Aerodynamic drag reduction technologies : proceedings of the CEAS/DragNet European Drag Reduction Conference, 19-21 June 2000, Potsdam, Germany. - (Notes on numerical fluid mechanics ; 76)},
  booktitle = {Aerodynamic drag reduction technologies : proceedings of the CEAS/DragNet European Drag Reduction Conference, 19-21 June 2000, Potsdam, Germany. - (Notes on numerical fluid mechanics ; 76)},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {3-540-41911-X (Print)},
  doi       = {10.1007/978-3-540-45359-8_26},
  pages     = {246 -- 255},
  year      = {2001},
  language  = {en}
}
@inproceedings{GellertButenweg2009,
  author    = {Gellert, Christoph and Butenweg, Christoph},
  title     = {Nichtlinearer Erdbebennachweis von Mauerwerksbauten},
  series = {Erdbeben und Mauerwerk : 11. D-A-CH-Tagung 2009 ; [10./11. September 2009 in Z{\"u}rich] / SGEB, Swiss Society for Earthquake Engineering and Structural Dynamics; Schweizerischer Ingenieur- und Architektenverein, Fachgruppe f{\"u}r Br{\"u}ckenbau und Hochbau. [Hrsg. Dazio, Alessandro ...]},
  booktitle = {Erdbeben und Mauerwerk : 11. D-A-CH-Tagung 2009 ; [10./11. September 2009 in Z{\"u}rich] / SGEB, Swiss Society for Earthquake Engineering and Structural Dynamics; Schweizerischer Ingenieur- und Architektenverein, Fachgruppe f{\"u}r Br{\"u}ckenbau und Hochbau. [Hrsg. Dazio, Alessandro ...]},
  publisher = {SIA},
  address   = {Z{\"u}rich},
  organization    = {D-A-C-H Tagung <11, 2009, Z{\"u}rich>},
  isbn      = {978-3-03732-021-1},
  pages     = {125 -- 132},
  year      = {2009},
  language  = {de}
}
@inproceedings{SchreiberKraftZuendorf2018,
  author    = {Schreiber, Marc and Kraft, Bodo and Z{\"u}ndorf, Albert},
  title     = {NLP Lean Programming Framework: Developing NLP Applications More Effectively},
  series = {Proceedings of NAACL-HLT 2018: Demonstrations, New Orleans, Louisiana, June 2 - 4, 2018},
  booktitle = {Proceedings of NAACL-HLT 2018: Demonstrations, New Orleans, Louisiana, June 2 - 4, 2018},
  doi       = {10.18653/v1/N18-5001 },
  pages     = {5 Seiten},
  year      = {2018},
  abstract  = {This paper presents NLP Lean Programming framework (NLPf), a new framework for creating custom natural language processing (NLP) models and pipelines by utilizing common software development build systems. This approach allows developers to train and integrate domain-specific NLP pipelines into their applications seamlessly. Additionally, NLPf provides an annotation tool which improves the annotation process significantly by providing a well-designed GUI and sophisticated way of using input devices. Due to NLPf's properties developers and domain experts are able to build domain-specific NLP applications more efficiently. NLPf is Opensource software and available at https:// gitlab.com/schrieveslaach/NLPf.},
  language  = {en}
}
@inproceedings{Bung2011,
  author    = {Bung, Daniel Bernhard},
  title     = {Non-intrusive measuring of air-water flow properties in self-aerated stepped spillway flow},
  series = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia},
  booktitle = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia},
  organization    = {International Association for Hydraulic Engineering and Research},
  isbn      = {978-0-85825-868-6},
  pages     = {2380 -- 2387},
  year      = {2011},
  language  = {en}
}
@inproceedings{EssingholtMeyerKuhnetal.2018,
  author    = {Essingholt, Felix and Meyer, Frederic and Kuhn, Peter and Schmidt, Philip and Benkner, Thorsten and Grabmaier, Anton},
  title     = {Non-invasive heart beat measurement using microwave resonators},
  series = {Proceedings, Vol. 2, Eurosensors 2018 Conference, Graz, Austria, 9-12 September 2018},
  booktitle = {Proceedings, Vol. 2, Eurosensors 2018 Conference, Graz, Austria, 9-12 September 2018},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2504-3900},
  doi       = {10.3390/proceedings2131002},
  pages     = {1002},
  year      = {2018},
  language  = {en}
}
@inproceedings{ButenwegNorda2013,
  author    = {Butenweg, Christoph and Norda, Hannah},
  title     = {Nonlinear analysis of masonry structures according to Eurocode 8},
  series = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)},
  booktitle = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)},
  editor    = {Adam, Christoph and Heuer, Rudolf and Lenhardt, Wolfgang and Schranz, Christian},
  isbn      = {978-3-902749-04-8},
  year      = {2013},
  language  = {en}
}
@inproceedings{GellertNordaButenweg2008,
  author    = {Gellert, Christoph and Norda, Hannah and Butenweg, Christoph},
  title     = {Nonlinear behaviour of masonry under cyclic loading},
  series = {7th European Conference on Structural Dynamics, EURODYN 2008 : 7-9 July 2008, Southampton},
  booktitle = {7th European Conference on Structural Dynamics, EURODYN 2008 : 7-9 July 2008, Southampton},
  organization    = {European Conference on Structural Dynamics, EURODYN <7, 2008, Southampton>},
  pages     = {1 -- 12},
  year      = {2008},
  language  = {en}
}
@inproceedings{SchwarteBuxbaumHeinoletal.1998,
  author    = {Schwarte, Rudolf and Buxbaum, Bernd and Heinol, Horst-Guenther and Xu, Zhanping and Ringbeck, Thorsten and Zang, Zhigang},
  title     = {Novel 3D-vision systems based on layout optimized PMD-structures},
  series = {Proceedings / OPTO 98, Internationaler Kongress und Fachausstellung f{\"u}r Optische Sensorik, Messtechnik und Elektronik, 18. - 20. Mai 1998, Kongreßzentrum Erfurt},
  booktitle = {Proceedings / OPTO 98, Internationaler Kongress und Fachausstellung f{\"u}r Optische Sensorik, Messtechnik und Elektronik, 18. - 20. Mai 1998, Kongreßzentrum Erfurt},
  publisher = {ACS Organisations GmbH},
  address   = {Wunsdorf},
  pages     = {197 -- 202},
  year      = {1998},
  language  = {en}
}
@inproceedings{MahdiRendonSchwageretal.2019,
  author    = {Mahdi, Zahra and Rend{\´o}n, Carlos and Schwager, Christian and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Novel concept for indirect solar-heated methane reforming},
  series = {AIP Conference Proceedings},
  volume    = {2126},
  booktitle = {AIP Conference Proceedings},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {0094-243X},
  doi       = {10.1063/1.5117694},
  pages     = {180014-1 -- 180014-7},
  year      = {2019},
  language  = {en}
}
@inproceedings{AridaKloockSchoening2006,
  author    = {Arida, Hassan A. and Kloock, Joachim P. and Sch{\"o}ning, Michael Josef},
  title     = {Novel organic membrane-based thin-film microsensors for the determination of heavy metal cations},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1545},
  year      = {2006},
  abstract  = {A first step towards the fabrication and electrochemical evaluation of thin-film microsensors based on organic PVC membranes for the determination of Hg(II), Cd(II), Pb(II) and Cu(II) ions in solutions has been realised. The membrane-coating mixture used in the preparation of this new type of microsensors is incorporating PVC as supporting matrix, o-nitrophenyloctylether (o-NPOE) as solvent mediator and a recently synthesized Hg[dimethylglyoxime(phene)]2+ and Bis-(4-hydroxyacetophenone)-ethylenediamine as electroactive materials for Hg(II) and Cd(II), respectively. A set of three commercialised ionophores for Cd(II), Pb(II) and Cu(II) has been also used for comparison. Thin-film microsensors based on these membranes showed a Nernstian response of slope (26-30 mV/dec.) for the respective tested cations. The potentiometric response characteristics (linear range, pH range, detection limit and response time) are comparable with those obtained by conventional membranes as well as coated wire electrodes prepared from the same membrane. The realisation of the new organic membrane-based thin-film microsensors overcomes the problem of an insufficient selectivity of solid-state-based thinfilm sensors.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{ReisgenSchleserScheiketal.2011,
  author    = {Reisgen, Uwe and Schleser, Markus and Scheik, Sven and Michaeli, Walter and Gr{\"o}nlund, Oliver and Neuß, Andreas and Wunderle, Johannes and Poprawe, Reinhart and R{\"o}sner, A. and Bobzin, Kirsten and Schl{\"a}fer, Thomas and Theiß, Sebastian and Kutschmann, Pia and Haberstroh, Edmund and Flock, Dustin and B{\"u}hrig-Polaczek, Andreas and Jakob, M.},
  title     = {Novel process chains for the production of plastics/metal-hybrids},
  series = {17th International Conference on Concurrent Enterprising (ICE 2011) : Aachen, Germany, 20 - 22 June 2011},
  booktitle = {17th International Conference on Concurrent Enterprising (ICE 2011) : Aachen, Germany, 20 - 22 June 2011},
  editor    = {Thoben, Klaus-Dieter},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  organization    = {Forschungsinstitut f{\"u}r Rationalisierung <Aachen> ; International Conference on Concurrent Enterprising <17, 2011, Aachen>},
  isbn      = {978-1-457-70772-8 ; 978-3-943024-05-0},
  pages     = {596 -- 604},
  year      = {2011},
  language  = {en}
}
@inproceedings{WetterKern2014,
  author    = {Wetter, Martin and Kern, Alexander},
  title     = {Number of lightning strikes to tall structures - comparison of calculations and measurements using a modern lightning monitoring system},
  series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  organization    = {International Conference on Lightning Protection <2014, Shanghai>},
  pages     = {1 -- 7},
  year      = {2014},
  language  = {en}
}
@inproceedings{MarinovaKerroumiLintermannetal.2016,
  author    = {Marinova, V. and Kerroumi, I. and Lintermann, A. and G{\"o}bbert, J.H. and Moulinec, C. and Rible, S. and Fournier, Y. and Behbahani, Mehdi},
  title     = {Numerical Analysis of the FDA Centrifugal Blood Pump},
  series = {NIC Symposium 2016},
  booktitle = {NIC Symposium 2016},
  isbn      = {978-3-95806-109-5},
  pages     = {355 -- 364},
  year      = {2016},
  language  = {de}
}
@inproceedings{FunkeBoernerKeinzetal.2012,
  author    = {Funke, Harald and B{\"o}rner, Sebastian and Keinz, Jan and Kusterer, K. and Kroninger, D. and Kitajima, J. and Kazari, M. and Horikama, A.},
  title     = {Numerical and experimental characterization of low NOx Micromix combustion principle for industrial hydrogen gas turbine applications},
  series = {Proceedings of ASME Turbo Expo 2012},
  booktitle = {Proceedings of ASME Turbo Expo 2012},
  pages     = {11},
  year      = {2012},
  language  = {en}
}
@inproceedings{FunkeBeckmannKeinzetal.2017,
  author    = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester},
  title     = {Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications},
  series = {Proceedings of the ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. Volume 4B: Combustion, Fuels and Emissions. Charlotte, North Carolina, USA. June 26-30, 2017},
  booktitle = {Proceedings of the ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. Volume 4B: Combustion, Fuels and Emissions. Charlotte, North Carolina, USA. June 26-30, 2017},
  publisher = {ASME},
  address   = {New York},
  isbn      = {978-0-7918-5085-5},
  doi       = {10.1115/GT2017-64795},
  year      = {2017},
  abstract  = {The Dry-Low-NOx (DLN) Micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The non-premixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 Vol.\%) Micromix combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel Micromix combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas the evaluated dual-fuel Micromix prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.},
  language  = {en}
}
@inproceedings{GiresiniButenwegAndreinietal.2014,
  author    = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.},
  title     = {Numerical calibration of a macro-element for vaultes system in historic churches},
  series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  organization    = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{StrieganHajAyedFunkeetal.2017,
  author    = {Striegan, C. and Haj Ayed, A. and Funke, Harald and Loechle, S. and Kazari, M. and Horikawa, A. and Okada, K. and Koga, K.},
  title     = {Numerical combustion and heat transfer simulations and validation for a hydrogen fueled "micromix" test combustor in industrial gas turbine applications},
  series = {Proceedings of the ASME Turbo Expo},
  booktitle = {Proceedings of the ASME Turbo Expo},
  number    = {Volume Part F130041-4B, 2017},
  isbn      = {978-079185085-5},
  doi       = {10.1115/GT2017-64719},
  year      = {2017},
  language  = {en}
}
@inproceedings{Kowalski2006,
  author    = {Kowalski, Julia},
  title     = {Numerical Debris Flow Simulation},
  series = {Schweizer Numerik Kolloquium : Book of Abstracts 12. April 2006},
  booktitle = {Schweizer Numerik Kolloquium : Book of Abstracts 12. April 2006},
  pages     = {1},
  year      = {2006},
  language  = {en}
}
@inproceedings{TaddeiReindlParketal.2011,
  author    = {Taddei, Francesca and Reindl, Lukas and Park, Jin and Butenweg, Christoph and Karadogan, Faruk},
  title     = {Numerical investigation of AAC wall panels based on the damage plasticity constitutive law},
  series = {Cement, Wapno, Beton ; 2011, 7, Special issue: 5th International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' to be held at Bydgoszcz to celebrate 60 years of AAC experience in Poland, Bydgoszcz, September 14-17, 2011},
  booktitle = {Cement, Wapno, Beton ; 2011, 7, Special issue: 5th International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' to be held at Bydgoszcz to celebrate 60 years of AAC experience in Poland, Bydgoszcz, September 14-17, 2011},
  publisher = {Stowarzyszenie Producent{\´o}w Cementu i Wapna},
  address   = {Krakow},
  organization    = {International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' <5, 2011, Bydgoszcz>},
  issn      = {1425-8129},
  pages     = {86 -- 91},
  year      = {2011},
  language  = {en}
}