@inproceedings{DoeringFeldmannKuhnhenneetal.2008, author = {D{\"o}ring, Bernd and Feldmann, Markus and Kuhnhenne, Markus and Hellberg, Jan}, title = {Implementing a thermal activation system into a light-weight steel deck element}, series = {Eurosteel 2008 : 5th European Conference on Steel and Composite Structures ; research, practice, new materials ; 3rd to 5th September 2008, Graz, Austria / ed. by Robert Ofner ...}, booktitle = {Eurosteel 2008 : 5th European Conference on Steel and Composite Structures ; research, practice, new materials ; 3rd to 5th September 2008, Graz, Austria / ed. by Robert Ofner ...}, publisher = {ECCS, European Convention for Construction Steelwork}, address = {Brussels}, organization = {Eurosteel <5, 2008, Graz>}, isbn = {92-0147-000-90}, pages = {941 -- 946}, year = {2008}, language = {en} } @phdthesis{Bung2023, author = {Bung, Daniel Bernhard}, title = {Imaging techniques for investigation of free-surface flows in hydraulic laboratories}, doi = {10.25926/BUW/0-172}, pages = {XXIII, 218 Seiten}, year = {2023}, abstract = {This thesis aims at the presentation and discussion of well-accepted and new imaging techniques applied to different types of flow in common hydraulic engineering environments. All studies are conducted in laboratory conditions and focus on flow depth and velocity measurements. Investigated flows cover a wide range of complexity, e.g. propagation of waves, dam-break flows, slightly and fully aerated spillway flows as well as highly turbulent hydraulic jumps. Newimagingmethods are compared to different types of sensorswhich are frequently employed in contemporary laboratory studies. This classical instrumentation as well as the general concept of hydraulic modeling is introduced to give an overview on experimental methods. Flow depths are commonly measured by means of ultrasonic sensors, also known as acoustic displacement sensors. These sensors may provide accurate data with high sample rates in case of simple flow conditions, e.g. low-turbulent clear water flows. However, with increasing turbulence, higher uncertainty must be considered. Moreover, ultrasonic sensors can provide point data only, while the relatively large acoustic beam footprint may lead to another source of uncertainty in case of relatively short, highly turbulent surface fluctuations (ripples) or free-surface air-water flows. Analysis of turbulent length and time scales of surface fluctuations from point measurements is also difficult. Imaging techniques with different dimensionality, however, may close this gap. It is shown in this thesis that edge detection methods (known from computer vision) may be used for two-dimensional free-surface extraction (i.e. from images taken through transparant sidewalls in laboratory flumes). Another opportunity in hydraulic laboratory studies comes with the application of stereo vision. Low-cost RGB-D sensors can be used to gather instantaneous, three-dimensional free-surface elevations, even in flows with very high complexity (e.g. aerated hydraulic jumps). It will be shown that the uncertainty of these methods is of similar order as for classical instruments. Particle Image Velocimetry (PIV) is a well-accepted and widespread imaging technique for velocity determination in laboratory conditions. In combination with high-speed cameras, PIV can give time-resolved velocity fields in 2D/3D or even as volumetric flow fields. PIV is based on a cross-correlation technique applied to small subimages of seeded flows. The minimum size of these subimages defines the maximum spatial resolution of resulting velocity fields. A derivative of PIV for aerated flows is also available, i.e. the so-called Bubble Image Velocimetry (BIV). This thesis emphasizes the capacities and limitations of both methods, using relatively simple setups with halogen and LED illuminations. It will be demonstrated that PIV/BIV images may also be processed by means of Optical Flow (OF) techniques. OF is another method originating from the computer vision discipline, based on the assumption of image brightness conservation within a sequence of images. The Horn-Schunck approach, which has been first employed to hydraulic engineering problems in the studies presented herein, yields dense velocity fields, i.e. pixelwise velocity data. As discussed hereinafter, the accuracy of OF competes well with PIV for clear-water flows and even improves results (compared to BIV) for aerated flow conditions. In order to independently benchmark the OF approach, synthetic images with defined turbulence intensitiy are used. Computer vision offers new opportunities that may help to improve the understanding of fluid mechanics and fluid-structure interactions in laboratory investigations. In prototype environments, it can be employed for obstacle detection (e.g. identification of potential fish migration corridors) and recognition (e.g. fish species for monitoring in a fishway) or surface reconstruction (e.g. inspection of hydraulic structures). It can thus be expected that applications to hydraulic engineering problems will develop rapidly in near future. Current methods have not been developed for fluids in motion. Systematic future developments are needed to improve the results in such difficult conditions.}, language = {en} } @inproceedings{BungValero2016, author = {Bung, Daniel Bernhard and Valero, Daniel}, title = {Image processing techniques for velocity estimation in highly aerated flows: bubble image velocimetry vs. optical flow}, series = {Sustainable Hydraulics in the Era of Global Change : Proceedings of the 4th IAHR Europe Congress (Liege, Belgium, 27-29 July 2016)}, booktitle = {Sustainable Hydraulics in the Era of Global Change : Proceedings of the 4th IAHR Europe Congress (Liege, Belgium, 27-29 July 2016)}, editor = {Dewals, Benjamin}, publisher = {CRC Press}, isbn = {978-1-138-02977-4}, doi = {10.1201/b21902-31}, pages = {151 -- 157}, year = {2016}, language = {en} } @inproceedings{BungValero2015, author = {Bung, Daniel Bernhard and Valero, Daniel}, title = {Image processing for bubble image velocimetry in self-aerated flows}, series = {E-proceedings of the 36th IAHR World Congress 28 June - 3 July, 2015, The Hague, the Netherlands}, booktitle = {E-proceedings of the 36th IAHR World Congress 28 June - 3 July, 2015, The Hague, the Netherlands}, organization = {IAHR World Congress <36, 2015, Den Haag>}, pages = {1 -- 8}, year = {2015}, language = {en} } @inproceedings{AhmedSchlenkhoffBung2011, author = {Ahmed, H. and Schlenkhoff, A. and Bung, Daniel Bernhard}, title = {Hydrodynamic characteristics of vertical slotted wall breakwaters}, series = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia}, booktitle = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia}, organization = {International Association for Hydraulic Engineering and Research}, isbn = {978-0-85825-868-6}, pages = {1179 -- 1186}, year = {2011}, language = {en} } @article{ErpicumCrookstonBombardellietal.2021, author = {Erpicum, Sebastien and Crookston, Brian M. and Bombardelli, Fabian and Bung, Daniel Bernhard and Felder, Stefan and Mulligan, Sean and Oertel, Mario and Palermo, Michele}, title = {Hydraulic structures engineering: An evolving science in a changing world}, series = {Wires Water}, volume = {8}, journal = {Wires Water}, number = {2}, publisher = {Wiley}, address = {Weinheim}, issn = {2049-1948}, doi = {10.1002/wat2.1505}, year = {2021}, language = {en} } @inproceedings{BungTullis2018, author = {Bung, Daniel Bernhard and Tullis, Blake}, title = {Hydraulic Structures - ISHS2018 in Perspective}, series = {7th IAHR International Symposium on Hydraulic Structures, Aachen, Germany, 15-18 May}, booktitle = {7th IAHR International Symposium on Hydraulic Structures, Aachen, Germany, 15-18 May}, isbn = {978-0-692-13277-7}, doi = {10.15142/T3WH2B}, pages = {9 seiten}, year = {2018}, language = {en} } @inproceedings{LangohrBungCrookston2022, author = {Langohr, Philipp and Bung, Daniel Bernhard and Crookston, Brian M.}, title = {Hybrid investigation of labyrinth weirs: Discharge capacity and energy dissipation}, series = {Proceedings of the 39th IAHR World Congress}, booktitle = {Proceedings of the 39th IAHR World Congress}, editor = {Ortega-S{\´a}nchez, Miguel}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, isbn = {978-90-832612-1-8}, issn = {2521-7119 (print)}, doi = {10.3850/IAHR-39WC252171192022738}, pages = {2313 -- 2318}, year = {2022}, abstract = {The replacement of existing spillway crests or gates with labyrinth weirs is a proven techno-economical means to increase the discharge capacity when rehabilitating existing structures. However, additional information is needed regarding energy dissipation of such weirs, since due to the folded weir crest, a three-dimensional flow field is generated, yielding more complex overflow and energy dissipation processes. In this study, CFD simulations of labyrinth weirs were conducted 1) to analyze the discharge coefficients for different discharges to compare the Cd values to literature data and 2) to analyze and improve energy dissipation downstream of the structure. All tests were performed for a structure at laboratory scale with a height of approx. P = 30.5 cm, a ratio of the total crest length to the total width of 4.7, a sidewall angle of 10° and a quarter-round weir crest shape. Tested headwater ratios were 0.089 ≤ HT/P ≤ 0.817. For numerical simulations, FLOW-3D Hydro was employed, solving the RANS equations with use of finite-volume method and RNG k-ε turbulence closure. In terms of discharge capacity, results were compared to data from physical model tests performed at the Utah Water Research Laboratory (Utah State University), emphasizing higher discharge coefficients from CFD than from the physical model. For upstream heads, some discrepancy in the range of ± 1 cm between literature, CFD and physical model tests was identified with a discussion regarding differences included in the manuscript. For downstream energy dissipation, variable tailwater depths were considered to analyze the formation and sweep-out of a hydraulic jump. It was found that even for high discharges, relatively low downstream Froude numbers were obtained due to high energy dissipation involved by the three-dimensional flow between the sidewalls. The effects of some additional energy dissipation devices, e.g. baffle blocks or end sills, were also analyzed. End sills were found to be non-effective. However, baffle blocks with different locations may improve energy dissipation downstream of labyrinth weirs.}, language = {en} } @inproceedings{ValeroBung2015, author = {Valero, Daniel and Bung, Daniel Bernhard}, title = {Hybrid investigation of air transport processes in moderately sloped stepped spillway flows}, series = {E-proceedings of the 36th IAHR World Congress 28 June - 3 July, 2015, The Hague, the Netherlands}, booktitle = {E-proceedings of the 36th IAHR World Congress 28 June - 3 July, 2015, The Hague, the Netherlands}, organization = {IAHR World Congress <36, 2015, Den Haag>}, pages = {1 -- 10}, year = {2015}, language = {en} } @incollection{GrossHeckenRenz1999, author = {Groß, Rolf Fritz and Hecken, M. and Renz, Ulrich}, title = {Hot gas filtration with ceramic filter candles: experimental and numerical investigations on fluid flow during element cleaning}, series = {High temperature gas cleaning. Vol. 2}, booktitle = {High temperature gas cleaning. Vol. 2}, editor = {Dittler, A. and Hemmer, G. and Kasper, G.}, publisher = {KIT Institut f{\"u}r Mechanische Verfahrenstechnik und Mechanik}, address = {Karlsruhe}, isbn = {3-9805220-1-6}, pages = {862 -- 873}, year = {1999}, abstract = {Ceramic hot gas filters are widely used in combined cycles based on pressurised fluidised beds. They fulfil most of the demands with respect to cleaning efficiency and long time durability, but their operation regarding the consumption of pulse gas and energy still has to be optimised. Experimental investigations were carried out to measure the flow field, the pressure and the gas temperature inside the filter candle during pulse jet cleaning. These results are compared with the results of a numerical procedure based on a solution of the two - dimensional conservation equations for momentum and energy. The observed difficulties handling different flow regimes like highly turbulent flow as well as Darcy flow simultaneously are discussed.}, language = {en} } @inproceedings{KirschFelberMarcheretal.2014, author = {Kirsch, Ansgar and Felber, W. and Marcher, Thomas and Fuchs, W.}, title = {Geotechnical challenges during design and construction of a ski resort in Azerbaijan}, series = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria}, booktitle = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria}, publisher = {{\"O}IAV - {\"O}sterreichischer Ingenieur- und Architekten-Verein}, address = {Wien}, organization = {Danube - European Conference on Geotechnical Engineering <15, 2014, Wien>}, isbn = {978-3-902593-01-6}, pages = {757 -- 762}, year = {2014}, language = {en} } @article{BienerBoykenSasseetal.1999, author = {Biener, Ernst and Boyken, P. and Sasse, T. and Arnold, J.}, title = {Geotechnical aspects of the construction of the integrated harbour sludge management system in Bremen-Seehausen / P. Boyken ; E. Biener ; T. Sasse ; J. Arnold}, series = {Geotechnical engineering for transportation infrastructure : proceedings of the twelfth European Conference on Soil Mechanics and Geotechnical Engineering, Amsterdam, Netherlands, 7 - 10 June 1999 ; theory and practice, planning and design, construction and maintenance. - Vol. 2}, journal = {Geotechnical engineering for transportation infrastructure : proceedings of the twelfth European Conference on Soil Mechanics and Geotechnical Engineering, Amsterdam, Netherlands, 7 - 10 June 1999 ; theory and practice, planning and design, construction and maintenance. - Vol. 2}, publisher = {Balkema}, address = {Rotterdam}, isbn = {90-5809-049-3}, pages = {909 -- 914}, year = {1999}, language = {en} } @article{KerresGredigkHoffmannJatheetal.2020, author = {Kerres, Karsten and Gredigk-Hoffmann, Sylvia and Jathe, R{\"u}diger and Orlik, Stefan and Sariyildiz, Mustafa and Schmidt, Torsten and Sympher, Klaus-Jochen and Uhlenbroch, Adrian}, title = {Future approaches for sewer system condition assessment}, series = {Water Practice \& Technology}, journal = {Water Practice \& Technology}, number = {15 (2)}, publisher = {IWA Publishing}, address = {London}, issn = {1751-231X}, doi = {10.2166/wpt.2020.027}, pages = {386 -- 393}, year = {2020}, abstract = {Different analytical approaches exist to describe the structural substance or wear reserve of sewer systems. The aim is to convert engineering assessments of often complex defect patterns into computational algorithms and determine a substance class for a sewer section or manhole. This analytically determined information is essential for strategic rehabilitation planning processes up to network level, as it corresponds to the most appropriate rehabilitation type and can thus provide decision-making support. Current calculation methods differ clearly from each other in parts, so that substance classes determined by the different approaches are only partially comparable with each other. The objective of the German R\&D cooperation project 'SubKanS' is to develop a methodology for classifying the specific defect patterns resulting from the interaction of all the individual defects, and their severities and locations. The methodology takes into account the structural substance of sewer sections and manholes, based on real data and theoretical considerations analogous to the condition classification of individual defects. The result is a catalogue of defect patterns and characteristics, as well as associated structural substance classifications of sewer systems (substance classes). The methodology for sewer system substance classification is developed so that the classification of individual defects can be transferred into a substance class of the sewer section or manhole, eventually taking into account further information (e.g. pipe material, nominal diameter, etc.). The result is a validated methodology for automated sewer system substance classification.}, language = {en} } @inproceedings{MuellerHueben2008, author = {M{\"u}ller, Karsten and H{\"u}ben, Susanne}, title = {From rehabilitation strategy up to formation of lots : implementation of a computer-aided decision support system}, series = {11th International Conference on Urban Drainage, Edinburgh, Scotland, UK, 31st August to 5th September 2008}, booktitle = {11th International Conference on Urban Drainage, Edinburgh, Scotland, UK, 31st August to 5th September 2008}, pages = {12 S. : graph. Darst.}, year = {2008}, language = {en} } @inproceedings{BungValero2017, author = {Bung, Daniel Bernhard and Valero, Daniel}, title = {FlowCV - An open-source toolbox for computer vision applications in turbulent flows}, series = {Proceedings of the 37th IAHR World Congress August 13 - 18, 2017, Kuala Lumpur, Malaysia}, booktitle = {Proceedings of the 37th IAHR World Congress August 13 - 18, 2017, Kuala Lumpur, Malaysia}, issn = {2521-716X}, pages = {5356 -- 5365}, year = {2017}, language = {en} } @incollection{FeldmannDoeringPyschny2016, author = {Feldmann, M. and D{\"o}ring, Bernd and Pyschny, D.}, title = {Floor systems; Sustainabilty analyses and assessments of steel bridges}, series = {Sustainable steel buildings : a practical guide for structures and envelopes}, booktitle = {Sustainable steel buildings : a practical guide for structures and envelopes}, publisher = {Wiley Blackwell}, address = {Chichester, West Sussex}, isbn = {978-1-118-74079-8 (PDF)}, pages = {198 -- 223}, year = {2016}, language = {en} } @inproceedings{DoeringKuhnhenneFeldmann2011, author = {D{\"o}ring, Bernd and Kuhnhenne, Markus and Feldmann, Markus}, title = {Floor systems - key elements for sustainable multi-storey buildings}, series = {SB11 Helsinki World Sustainable Building Conference : 18. - 21.10.2011}, booktitle = {SB11 Helsinki World Sustainable Building Conference : 18. - 21.10.2011}, organization = {World Sustainable Building Conference <2011, Helsinki>}, pages = {1 -- 6}, year = {2011}, language = {en} } @inproceedings{BungOertelSchlenkhoffetal.2010, author = {Bung, Daniel Bernhard and Oertel, M. and Schlenkhoff, A. and Schlurmann, Torsten}, title = {Flash flood awareness and prevention in Germany}, series = {Early warning for flash floods : international workshop, Praha 2011 : workshop proceedings}, booktitle = {Early warning for flash floods : international workshop, Praha 2011 : workshop proceedings}, editor = {Obrusnik, Ivan}, organization = {Czech Hydrometeorological Institute}, isbn = {978-80-86690-91-9}, pages = {34 -- 40}, year = {2010}, language = {en} } @inproceedings{OertelBungSchlenkhoff2009, author = {Oertel, M. and Bung, Daniel Bernhard and Schlenkhoff, Andreas}, title = {Flash flood awareness and prevention}, series = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, booktitle = {Water engineering for sustainable environment : 33rd IAHR congress ; 9 - 14 August 2009, Vancouver, British Columbia, Canada}, organization = {International Association for Hydraulic Engineering and Research}, isbn = {9789078046080}, pages = {1 CD-ROM}, year = {2009}, language = {en} } @article{HoettgesFeldhausBrockhausetal.1992, author = {H{\"o}ttges, J{\"o}rg and Feldhaus, R. and Brockhaus, T. and Rouv{\´e}, Gerhard}, title = {Finite Element Simulation of Flow and Pollution Transport applied to a Part of the River Rhine / Feldhaus, R.; J. H{\"o}ttges, T. Brockhaus; G. Rouv{\´e}}, series = {Hydraulic and environmental modelling : proceedings of the Second International Conference on Hydraulic and Environmental Modelling of Coastal, Estuarine, and River Waters / [IAHR-AIRH]. Ed. by R. A. Falconer}, journal = {Hydraulic and environmental modelling : proceedings of the Second International Conference on Hydraulic and Environmental Modelling of Coastal, Estuarine, and River Waters / [IAHR-AIRH]. Ed. by R. A. Falconer}, publisher = {Ashgate}, address = {Aldershot, Hants, UK [u.a.]}, year = {1992}, language = {en} }