@inproceedings{GoettenFingerHavermannetal.2020,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Full Configuration Drag Estimation of Small-to-Medium Range UAVs and its Impact on Initial Sizing Optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  booktitle = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2020},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used on surveillance, reconnaissance, and search and rescue missions. The aircraft are simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@article{ButenwegRosin2020,
  author    = {Butenweg, Christoph and Rosin, Julia},
  title     = {Seismischer Nachweis von Mauerwerksbauten in deutschen Erdbebengebieten},
  series = {Mauerwerk},
  volume    = {24},
  journal   = {Mauerwerk},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022},
  doi       = {10.1002/dama.202000006},
  pages     = {108 -- 113},
  year      = {2020},
  abstract  = {Mit finanzieller Unterst{\"u}tzung der Deutschen Gesellschaft f{\"u}r Mauerwerks- und Wohnungsbau e.V. (DGfM) und des Deutschen Instituts f{\"u}r Bautechnik in Berlin (DIBt) wurden zwei aufeinander aufbauende Forschungsvorhaben zur Verbesserung der seismischen Nachweise von Mauerwerksbauten in deutschen Erdbebengebieten durchgef{\"u}hrt. Zun{\"a}chst wurde das seismische Verhalten von drei modernen unbewehrten Mauerwerksgeb{\"a}uden in der Region Emilia Romagna in Italien w{\"a}hrend der Erdbebenserie im Jahr 2012 in Kooperation mit der Universit{\"a}t Pavia eingehend untersucht. Aufbauend auf den Erkenntnissen dieser Untersuchungen wurde ein verbessertes seismisches Bemessungskonzept f{\"u}r unbewehrte Mauerwerksbauten erarbeitet. Der Beitrag stellt die wesentlichen Ergebnisse dieser Forschungsarbeiten und deren Eingang in die Normung vor.},
  language  = {de}
}
@article{MarinkovicButenweg2020,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Ausfachungen aus Ziegelmauerwerk in Stahlbetonrahmentragwerken unter Erdbebenbeanspruchung},
  series = {Mauerwerk},
  volume    = {24},
  journal   = {Mauerwerk},
  number    = {4},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022},
  doi       = {10.1002/dama.202000011},
  pages     = {194 -- 205},
  year      = {2020},
  abstract  = {Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk weisen nach Erdbeben h{\"a}ufig schwere Sch{\"a}den auf. Gr{\"u}nde hierf{\"u}r sind die Beanspruchungen der Ausfachungsw{\"a}nde durch die aufgezwungenen Rahmenverformungen in Wandebene und die gleichzeitig auftretenden Tr{\"a}gheitskr{\"a}fte senkrecht zur Wandebene in Kombination mit der konstruktiven Ausf{\"u}hrung des Ausfachungsmauerwerks. Die Ausfachung wird in der Regel knirsch gegen die Rahmenst{\"u}tzen gemauert, wobei der Verschluss der oberen Fuge mit M{\"o}rtel oder Montageschaum erfolgt. Dadurch kommt es im Erdbebenfall zu lokalen Interaktionen zwischen Ausfachung und Rahmen, die in der Folge zu einem Versagen einzelner Ausfachungsw{\"a}nde oder zu einem sukzessiven Versagen des Gesamtgeb{\"a}udes f{\"u}hren k{\"o}nnen. Die beobachteten Sch{\"a}den waren die Motivation daf{\"u}r, in dem europ{\"a}ischen Forschungsprojekt INSYSME f{\"u}r Stahlbetonrahmentragwerke mit Ausfachungen aus hochw{\"a}rmed{\"a}mmenden Ziegelmauerwerk innovative L{\"o}sungen zur Verbesserung des seismischen Verhaltens zu entwickeln. Der vorliegende Beitrag stellt die im Rahmen des Projekts von den deutschen Projektpartnern (Universit{\"a}t Kassel, SDA-engineering GmbH) entwickelten L{\"o}sungen vor und vergleicht deren seismisches Verhalten mit der traditionellen Ausf{\"u}hrung der Ausfachungsw{\"a}nde. Grundlage f{\"u}r den Vergleich sind statisch-zyklische Wandversuche und Simulationen auf Wandebene. Aus den Ergebnissen werden Empfehlungen f{\"u}r die erdbebensichere Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk abgeleitet.},
  language  = {de}
}
@article{MarinkovicButenweg2020,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Earthquake-proof system for masonry infills in RC frame structures},
  series = {International Journal of Masonry Research and Innovation},
  volume    = {5},
  journal   = {International Journal of Masonry Research and Innovation},
  number    = {2},
  publisher = {Inderscience Enterprises},
  address   = {Olney, Bucks},
  issn      = {2056-9467},
  doi       = {10.1504/IJMRI.2020.106328},
  pages     = {185 -- 208},
  year      = {2020},
  language  = {de}
}
@article{MichelButenwegKlinkel2020,
  author    = {Michel, P. and Butenweg, Christoph and Klinkel, S.},
  title     = {Einfluss der dynamischen Steifigkeit von Flach-und Pfahlgr{\"u}ndungen auf die Dynamik von Onshore-Windenergieanlagen},
  series = {Bauingenieur},
  volume    = {95},
  journal   = {Bauingenieur},
  number    = {4},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {0005-6650},
  pages     = {139 -- 146},
  year      = {2020},
  language  = {de}
}
@article{UlmerGroeningerBraunetal.2020,
  author    = {Ulmer, Jessica and Gr{\"o}ninger, Marc and Braun, Sebastian and Wollert, J{\"o}rg},
  title     = {AR Arbeitspl{\"a}tze: F{\"u}r hochflexible und skalierbare Produktionsumgebungen},
  series = {atp Magazin},
  volume    = {62},
  journal   = {atp Magazin},
  number    = {10},
  publisher = {Vulkan-Verlag},
  address   = {Essen},
  issn      = {2364-3137},
  doi       = {10.17560/atp.v62i10.2495},
  year      = {2020},
  abstract  = {Trotz fortschreitender Automatisierung bleiben manuelle T{\"a}tigkeiten ein wichtiger Baustein der Fertigung kundenindividueller Produkte. Um die Mitarbeiter(innen) zu unterst{\"u}tzen und um eine effiziente Arbeit zu erm{\"o}glichen, werden zunehmend auf Augmented Reality (AR) basierende Systeme eingesetzt. Die vorgestellte Arbeit konzentriert sich auf die Entwicklung ganzheitlicher AR-Arbeitspl{\"a}tze f{\"u}r den Einsatz in kleinen und mittleren Unternehmen (KMU). Das entwickelte AR- Handarbeitskonzept beinhaltet eine Just-in-time-Darstellung der Arbeitsaufgaben auf Werkst{\"u}cken mit automatisierter Fertigungskontrolle. Als Reaktion auf kurze Produktlebenszyklen und hohe Produktvielfalten sind alle Komponenten auf maximale Flexibilit{\"a}t ausgelegt. Ein Umr{\"u}sten auf neue Produkte kann innerhalb von Minuten erfolgen.},
  language  = {de}
}
@inproceedings{SildatkeKarwanniKraftetal.2020,
  author    = {Sildatke, Michael and Karwanni, Hendrik and Kraft, Bodo and Schmidts, Oliver and Z{\"u}ndorf, Albert},
  title     = {Automated Software Quality Monitoring in Research Collaboration Projects},
  series = {ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops},
  booktitle = {ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops},
  publisher = {IEEE},
  address   = {New York, NY},
  doi       = {10.1145/3387940.3391478},
  pages     = {603 -- 610},
  year      = {2020},
  abstract  = {In collaborative research projects, both researchers and practitioners work together solving business-critical challenges. These projects often deal with ETL processes, in which humans extract information from non-machine-readable documents by hand. AI-based machine learning models can help to solve this problem. Since machine learning approaches are not deterministic, their quality of output may decrease over time. This fact leads to an overall quality loss of the application which embeds machine learning models. Hence, the software qualities in development and production may differ. Machine learning models are black boxes. That makes practitioners skeptical and increases the inhibition threshold for early productive use of research prototypes. Continuous monitoring of software quality in production offers an early response capability on quality loss and encourages the use of machine learning approaches. Furthermore, experts have to ensure that they integrate possible new inputs into the model training as quickly as possible. In this paper, we introduce an architecture pattern with a reference implementation that extends the concept of Metrics Driven Research Collaboration with an automated software quality monitoring in productive use and a possibility to auto-generate new test data coming from processed documents in production. Through automated monitoring of the software quality and auto-generated test data, this approach ensures that the software quality meets and keeps requested thresholds in productive use, even during further continuous deployment and changing input data.},
  language  = {en}
}
@book{LabischWaehlisch2020,
  author    = {Labisch, Susanna and W{\"a}hlisch, Georg},
  title     = {Technisches Zeichnen: Eigenst{\"a}ndig lernen und effektiv {\"u}ben},
  edition   = {6th ed.},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  isbn      = {978-3-658-30650-2 (E-Book)},
  doi       = {10.1007/978-3-658-30650-2},
  pages     = {Online-Ressource (XI, 296 S. 300 Abb., 81 Abb. in Farbe)},
  year      = {2020},
  language  = {de}
}
@book{YoshinobuSchoening2020,
  author    = {Yoshinobu, Tatsuo and Sch{\"o}ning, Michael Josef},
  title     = {Light-addressing and chemical imaging technologies for electrochemical sensing},
  editor    = {Yoshinobu, Tatsuo and Sch{\"o}ning, Michael Josef},
  publisher = {MDPI},
  address   = {Basel},
  isbn      = {978-3-03943-029-1},
  doi       = {10.3390/books978-3-03943-029-1},
  pages     = {122 Pages},
  year      = {2020},
  language  = {en}
}
@inproceedings{IomdinaKiselevaKotliaretal.2020,
  author    = {Iomdina, Elena N. and Kiseleva, Anna A. and Kotliar, Konstantin and Luzhnov, Petr V.},
  title     = {Quantification of Choroidal Blood Flow Using the OCT-A System Based on Voxel Scan Processing},
  series = {Proceedings of the International Conference on Biomedical Innovations and Applications- BIA 2020},
  booktitle = {Proceedings of the International Conference on Biomedical Innovations and Applications- BIA 2020},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {978-1-7281-7073-2},
  doi       = {10.1109/BIA50171.2020.9244511},
  pages     = {41 -- 44},
  year      = {2020},
  abstract  = {The paper presents a method for the quantitative assessment of choroidal blood flow using an OCT-A system. The developed technique for processing of OCT-A scans is divided into two stages. At the first stage, the identification of the boundaries in the selected portion was performed. At the second stage, each pixel mark on the selected layer was represented as a volume unit, a voxel, which characterizes the region of moving blood. Three geometric shapes were considered to represent the voxel. On the example of one OCT-A scan, this work presents a quantitative assessment of the blood flow index. A possible modification of two-stage algorithm based on voxel scan processing is presented.},
  language  = {en}
}
@inproceedings{FrantzBinderBuschetal.2020,
  author    = {Frantz, Cathy and Binder, Matthias and Busch, Konrad and Ebert, Miriam and Heinrich, Andreas and Kaczmarkiewicz, Nadine and Schl{\"o}gl-Knothe, B{\"a}rbel and Kunze, Tobias and Schuhbauer, Christian and Stetka, Markus and Schwager, Christian and Spiegel, Michael and Teixeira Boura, Cristiano Jos{\´e} and Bauer, Thomas and Bonk, Alexander and Eisen, Stefan and Funck, Bernhard},
  title     = {Basic Engineering of a High Performance Molten Salt Tower Receiver System},
  series = {AIP Conference Proceedings},
  booktitle = {AIP Conference Proceedings},
  doi       = {10.1063/5.0085895},
  pages     = {1 -- 10},
  year      = {2020},
  abstract  = {The production of dispatchable renewable energy will be one of the most important key factors of the future energy supply. Concentrated solar power (CSP) plants operated with molten salt as heat transfer and storage media are one opportunity to meet this challenge. Due to the high concentration factor of the solar tower technology the maximum process temperature can be further increased which ultimately decreases the levelized costs of electricity of the technology (LCOE). The development of an improved tubular molten salt receiver for the next generation of molten salt solar tower plants is the aim of this work. The receiver is designed for a receiver outlet temperature up to 600 °C. Together with a complete molten salt system, the receiver will be integrated into the Multi-Focus-Tower (MFT) in J{\"u}lich (Germany). The paper describes the basic engineering of the receiver, the molten salt tower system and a laboratory corrosion setup.},
  language  = {en}
}
@article{Stulpe2020,
  author    = {Stulpe, Werner},
  title     = {Pairwise coexistence of effects versus coexistence},
  series = {Journal of Physics: Conference Series},
  volume    = {1638},
  journal   = {Journal of Physics: Conference Series},
  number    = {012004},
  publisher = {IOP},
  address   = {Bristol},
  issn      = {1742-6596},
  doi       = {10.1088/1742-6596/1638/1/012004},
  pages     = {1 -- 21},
  year      = {2020},
  language  = {en}
}
@inproceedings{MarinkovicButenweg2020,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Seismic behaviour of RC frames with uncoupled masonry infills having two storeys or two bays},
  series = {Brick and Block Masonry - From Historical to Sustainable Masonry. Proceedings of the 17th International Brick/Block Masonry Conference},
  booktitle = {Brick and Block Masonry - From Historical to Sustainable Masonry. Proceedings of the 17th International Brick/Block Masonry Conference},
  publisher = {CRC Press},
  address   = {London},
  doi       = {10.1201/9781003098508-72},
  pages     = {1 -- 7},
  year      = {2020},
  abstract  = {Reinforced concrete (RC) structures with masonry infills are widely used for several types of buildings all over the world. However, it is well known that traditional masonry infills constructed with rigid contact to the surrounding RC frame performed rather poor in past earthquakes. Masonry infills showed severe in-plane damages and failed in many cases under out-of-plane seismic loading. As the undesired interactions between frames and infills changes the load transfer on building level, complete collapses of buildings were observed. A possible solution is uncoupling of masonry infills to the frame to reduce the infill contribution activated by the frame deformation under horizontal loading. The paper presents numerical simulations on RC frames equipped with the innovative decoupling system INODIS. The system was developed within the European project INSYSME and allows an effective uncoupling of frame and infill. The simulations are carried out with a micro-modelling approach, which is able to predict the complex nonlinear behaviour resulting from the different materials and their interaction. Each brick is modelled individually and connected taking into account nonlinearity of a brick mortar interface. The calibration of the model is based on small specimen tests and experimental results for one bay one storey frame are used for the validation. The validated model is further used for parametric studies on two storey and two bay infilled frames. The response and change of the structural stiffness are analysed and compared to the traditionally infilled frame. The results confirm the effectiveness of the INODIS system with less damage and relatively low contribution of the infill at high drift levels. In contrast to the uncoupled system configurations, traditionally infilled frames experienced brittle failure at rather low drift levels.},
  language  = {en}
}
@book{ButenwegHoffmeisterHoltschoppenetal.2020,
  author    = {Butenweg, Christoph and Hoffmeister, Benno and Holtschoppen, Britta and Klinkel, Sven and Rosin, Julia and Schmitt, Timo},
  title     = {Seismic design of industrial facilities 2020: proceedings of the 2nd International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference)},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {524 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{MarkinkovicButenwegPaveseetal.2020,
  author    = {Markinkovic, Marko and Butenweg, Christoph and Pavese, A. and Lanese, I. and Hoffmeister, B. and Pinkawa, M. and Vulcu, C. and Bursi, O. and Nardin, C. and Paolacci, F. and Quinci, G. and Fragiadakis, M. and Weber, F. and Huber, P. and Renault, P. and G{\"u}ndel, M. and Dyke, S. and Ciucci, M. and Marino, A.},
  title     = {Investigation of the seismic behaviour of structural and nonstructural components in industrial facilities by means of shaking table tests},
  series = {Seismic design of industrial facilities 2020},
  booktitle = {Seismic design of industrial facilities 2020},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {159 -- 172},
  year      = {2020},
  language  = {en}
}
@inproceedings{CacciatoreButenweg2020,
  author    = {Cacciatore, Pamela and Butenweg, Christoph},
  title     = {Seismic safety of cylindrical granular material steel silos under seismic loading},
  series = {Seismic design of industrial facilities 2020},
  booktitle = {Seismic design of industrial facilities 2020},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {231 -- 244},
  year      = {2020},
  language  = {en}
}
@inproceedings{MichelRosinButenwegetal.2020,
  author    = {Michel, Philipp and Rosin, Julia and Butenweg, Christoph and Klinkel, Sven},
  title     = {Soil-dependent earthquake spectra in the analysis of liquid-storage-tanks on compliant soil},
  series = {Seismic design of industrial facilities 2020},
  booktitle = {Seismic design of industrial facilities 2020},
  publisher = {Apprimus Verlag},
  address   = {Aachen},
  isbn      = {978-3-86359-729-0},
  pages     = {245 -- 254},
  year      = {2020},
  abstract  = {A further development of the Added-Mass-Method allows the combined representation of the effects of both soil-structure-interaction and fluid-structure interaction on a liquid-filled-tank in one model. This results in a practical method for describing the dynamic fluid pressure on the tank shell during joint movement. The fluid pressure is calculated on the basis of the tank's eigenform and the earthquake acceleration and represented by additional masses on the shell. The bearing on compliant ground is represented by replacement springs, which are calculated dependent on the local soil composition. The influence of the shear modulus of the compliant soil is clearly visible in the pressure curves and the stress distribution in the shell. The acceleration spectra are also dependent on soil stiffness. According to Eurocode-8 the acceleration spectra are determined for fixed soil-classes, instead of calculating the accelerations for each site in direct dependence on the soil composition. This leads to unrealistic sudden changes in the system's response. Therefore, earthquake spectra are calculated for different soil models in direct dependence of the shear modulus. Thus, both the acceleration spectra and the replacement springs match the soil composition. This enables a reasonable and consistent calculation of the system response for the actual conditions at each site.},
  language  = {en}
}
@article{HueningBackes2020,
  author    = {H{\"u}ning, Felix and Backes, Andreas},
  title     = {Direct observation of large Barkhausen jump in thin Vicalloy wires},
  series = {IEEE Magnetics Letters},
  volume    = {11},
  journal   = {IEEE Magnetics Letters},
  number    = {Art. 2506504},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {1949-307X},
  doi       = {10.1109/LMAG.2020.3046411},
  pages     = {1 -- 4},
  year      = {2020},
  language  = {en}
}
@article{GazdaMaurischat2020,
  author    = {Gazda, Quentin and Maurischat, Andreas},
  title     = {Special functions and Gauss-Thakur sums in higher rank and dimension},
  publisher = {De Gruyter},
  address   = {Berlin},
  pages     = {26 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{ChavezBermudezWollert2020,
  author    = {Chavez Bermudez, Victor Francisco and Wollert, J{\"o}rg},
  title     = {Arduino based Framework for Rapid Application Development of a Generic IO-Link interface},
  series = {Kommunikation und Bildverarbeitung in der Automation. Ausgew{\"a}hlte Beitr{\"a}ge der Jahreskolloquien KommA und BVAu 2018},
  booktitle = {Kommunikation und Bildverarbeitung in der Automation. Ausgew{\"a}hlte Beitr{\"a}ge der Jahreskolloquien KommA und BVAu 2018},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-59895-5},
  doi       = {10.1007/978-3-662-59895-5_2},
  pages     = {21 -- 33},
  year      = {2020},
  abstract  = {The implementation of IO-Link in the automation industry has increased over the years. Its main advantage is it offers a digital point-to-point plugand-play interface for any type of device or application. This simplifies the communication between devices and increases productivity with its different features like self-parametrization and maintenance. However, its complete potential is not always used. The aim of this paper is to create an Arduino based framework for the development of generic IO-Link devices and increase its implementation for rapid prototyping. By generating the IO device description file (IODD) from a graphical user interface, and further customizable options for the device application, the end-user can intuitively develop generic IO-Link devices. The peculiarity of this framework relies on its simplicity and abstraction which allows to implement any sensor functionality and virtually connect any type of device to an IO-Link master. This work consists of the general overview of the framework, the technical background of its development and a proof of concept which demonstrates the workflow for its implementation.},
  language  = {en}
}