@article{AlebouyehSamamiPieperBreitbachetal.2014,
  author    = {Alebouyeh Samami, Behzad and Pieper, Martin and Breitbach, Gerd and Hodapp, Josef},
  title     = {Heat production in the windings of the stators of electric machines under stationary condition},
  series = {Heat and mass transfer},
  volume    = {50},
  journal   = {Heat and mass transfer},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {0947-7411 (Print) ; 1432-1181 (E-Journal)},
  doi       = {10.1007/s00231-014-1371-8},
  pages     = {1707 -- 1716},
  year      = {2014},
  abstract  = {In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results.},
  language  = {en}
}
@article{PauksztatKuperjansMeyer2005,
  author    = {Pauksztat, Anja and Kuperjans, Isabel and Meyer, J{\"o}rg},
  title     = {Produktbezogene Referenzwerte f{\"u}r Energieeffizienz und CO2-Emissionen},
  series = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  volume    = {55},
  journal   = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  number    = {6},
  issn      = {0013-743X},
  pages     = {374 -- 376},
  year      = {2005},
  language  = {de}
}
@article{KuperjansStarkeEsseretal.2000,
  author    = {Kuperjans, Isabel and Starke, M. and Esser, J. and [u.a.],},
  title     = {Analyse und Konzeption von Energieanlagen unter {\"o}kologischen, wirtschaftlichen und technischen Gesichtspunkten},
  series = {WLB : Umwelttechnik f{\"u}r Industrie und Kommune},
  volume    = {44},
  journal   = {WLB : Umwelttechnik f{\"u}r Industrie und Kommune},
  number    = {11/12},
  issn      = {0341-2679},
  pages     = {26 -- 29},
  year      = {2000},
  language  = {de}
}
@article{KuperjansEsserMeyeretal.2000,
  author    = {Kuperjans, Isabel and Esser, J. and Meyer, J{\"o}rg and Donner, O.},
  title     = {Gestaltung und Bewertung von Energieanlagen unter {\"o}kologischen, wirtschaftlichen und technischen Gesichtspunkten},
  series = {Umweltwirtschaftsforum : UWF},
  volume    = {8},
  journal   = {Umweltwirtschaftsforum : UWF},
  number    = {3},
  issn      = {0943-3481},
  pages     = {53 -- 58},
  year      = {2000},
  language  = {de}
}
@article{Kuperjans2011,
  author    = {Kuperjans, Isabel},
  title     = {Gute Planung ist alles : Energieeffizienz in der Pharmaproduktion},
  series = {Pharma + Food},
  volume    = {2011},
  journal   = {Pharma + Food},
  number    = {2},
  publisher = {H{\"u}thig},
  address   = {Heidelberg},
  issn      = {1434-8942},
  pages     = {8 -- 10},
  year      = {2011},
  language  = {de}
}
@article{AugensteinHerbergsKuperjans2006,
  author    = {Augenstein, Eckardt and Herbergs, S. and Kuperjans, Isabel},
  title     = {TOP-Energy : ein Werkzeug zur Optimierung der Geb{\"a}udeenergieversorgung},
  series = {KI : K{\"a}lte, Luft, Klimatechnik},
  journal   = {KI : K{\"a}lte, Luft, Klimatechnik},
  number    = {5},
  issn      = {1865-5432},
  pages     = {198 -- 201},
  year      = {2006},
  language  = {de}
}
@article{MarxSchenkBehrensetal.2013,
  author    = {Marx, Ulrich and Schenk, Friedrich and Behrens, Jan and Meyr, Ulrike and Wanek, Paul and Zang, Werner and Schmitt, Robert and Br{\"u}stle, Oliver and Zenke, Martin and Klocke, Fritz},
  title     = {Automatic production of induced pluripotent stem cells},
  series = {Procedia CIRP : First CIRP Conference on BioManufacturing},
  volume    = {Vol. 5},
  journal   = {Procedia CIRP : First CIRP Conference on BioManufacturing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  pages     = {2 -- 6},
  year      = {2013},
  language  = {en}
}
@article{SrivastavaLahiriMaitietal.2014,
  author    = {Srivastava, A. and Lahiri, S. and Maiti, M. and Knolle, F. and Hoyler, Friedrich and Scherer, Ulrich W. and Schnug, E. W.},
  title     = {Study of naturally occurring radioactive material (NORM) in top soil of Punjab State from the North Western part of India},
  series = {Journal of Radioanalytical and Nuclear Chemistry},
  volume    = {2014},
  journal   = {Journal of Radioanalytical and Nuclear Chemistry},
  number    = {302},
  publisher = {Springer Nature},
  address   = {Basel},
  issn      = {1588-2780 (E-Journal); 0022-4081 (Print); 0134-0719 (Print); 0236-5731 (Print); 1417-2097 (Print)},
  doi       = {0.1007/s10967-014-3450-1},
  pages     = {1049 -- 1052},
  year      = {2014},
  language  = {en}
}
@article{Kern2003,
  author    = {Kern, Alexander},
  title     = {Risikomanagement f{\"u}r den Blitzschutz - Absch{\"a}tzung des Blitzschadensrisikos nach der neuen Vornorm VDE V 0185 Teil 2 : 2002},
  year      = {2003},
  abstract  = {Ein vorausschauendes Risikomanagement beinhaltet, Risiken zu kalkulieren. Es liefert Entscheidungsgrundlagen, um diese Risiken zu begrenzen und es macht transparent,welche Risiken sinnvoll {\"u}ber Versicherungen abgedeckt werden sollten. Bei Unternehmen, die mit umfangreichen elektronischenEinrichtungen produzieren oder Dienstleistungen erbringen (und das sind heutzutage wohl die meisten), muss auch das Risiko durch Blitzeinwirkungen besondere Ber{\"u}cksichtigung finden. Dabei ist zu beachten, dass der Schaden aufgrund der Nichtverf{\"u}gbarkeit der elektronischen Einrichtungen und damit derProduktion bzw. der Dienstleistung und ggf. der Verlust von Daten den Hardwareschaden an der betroffenen Anlage oft bei weitem {\"u}bersteigt.},
  language  = {de}
}
@article{KernKrichel2003,
  author    = {Kern, Alexander and Krichel, Frank},
  title     = {{\"U}berlegungen zum Blitzschutzkonzept f{\"u}r regenerative Energieanlagen},
  year      = {2003},
  abstract  = {Dem Blitzschutz von Anlagen der regenerativen Energien kommt in Zukunft eine steigende Bedeutung zu. Dabei ist es notwendig zu ber{\"u}cksichtigen, dass die Schutzmaßnahmen technisch/wirtschaftlich ausgewogen sind. Erbauer, Besitzer oder Benutzer von netzautarken Hybridanlagen haben zu entscheiden, ob die Anlage einen Schutz braucht oder nicht. Um diese Entscheidung zu f{\"a}llen, ist eine Risikoanalyse als erster Schritt sinnvoll. Diese muss dabei die f{\"u}r die Hybridanlage relevanten Schadenarten und spezifischen Parameter, Werte und Randbedingungen mit einbeziehen. Dazu ist die Hilfe eines Blitzschutzexperten sehr hilfreich.},
  subject      = {Alternative Energiequelle},
  language  = {de}
}
@article{JildehWagnerSchoeningetal.2015,
  author    = {Jildeh, Zaid B. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Pieper, Martin},
  title     = {Simulating the electromagnetic-thermal treatment of thin aluminium layers for adhesion improvement},
  series = {Physica status solidi (a)},
  volume    = {Vol. 212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431893},
  pages     = {1234 -- 1241},
  year      = {2015},
  abstract  = {A composite layer material used in packaging industry is made from joining layers of different materials using an adhesive. An important processing step in the production of aluminium-containing composites is the surface treatment and consequent coating of adhesive material on the aluminium surface. To increase adhesion strength between aluminium layer and the adhesive material, the foil is heat treated. For efficient heating, induction heating was considered as state-of-the-art treatment process. Due to the complexity of the heating process and the unpredictable nature of the heating source, the control of the process is not yet optimised. In this work, a finite element analysis of the process was established and various process parameters were studied. The process was simplified and modelled in 3D. The numerical model contains an air domain, an aluminium layer and a copper coil fitted with a magnetic field concentrating material. The effect of changing the speed of the aluminium foil (or rolling speed) was studied with the change of the coil current. Statistical analysis was used for generating a general control equation of coil current with changing rolling speed.},
  language  = {en}
}
@article{BorchertHasenbeckJungbluthetal.2009,
  author    = {Borchert, J{\"o}rg and Hasenbeck, Marc and Jungbluth, Christian and Schemm, Ralf},
  title     = {Bewertung und Steuerung von Gasspeichern bzw. Gasspeicherscheiben},
  series = {Zeitschrift f{\"u}r Energiewirtschaft},
  volume    = {33},
  journal   = {Zeitschrift f{\"u}r Energiewirtschaft},
  number    = {4},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1866-2765},
  doi       = {10.1007/s12398-009-0033-x},
  pages     = {279 -- 293},
  year      = {2009},
  abstract  = {In diesem Artikel werden zun{\"a}chst einleitend der Gasmarkt Deutschland und der sich daraus ergebende Speicherbedarf skizziert. Folgend wird auf verschiedene Speichernutzen aus betriebswirtschaftlicher Perspektive eingegangen und die in diesem Artikel vorgestellten Bewertungsverfahren einleitend beschrieben. In diesem Artikel werden stochastische Optimierungsmethoden aufgegriffen, die sowohl eine Bewertung der Speicher gegen{\"u}ber einem Spotpreis, als auch gegen{\"u}ber einer gesamten Forwardcurve erm{\"o}glichen. Hierzu werden zun{\"a}chst Modelle zur Beschreibung der Marktpreise vorgestellt und anhand empirischer Daten kalibriert. Dann wird eine beispielhafte Speicherscheibe zun{\"a}chst auf Basis der LeastSquareMonteCarloTechnik gegen{\"u}ber dem stochastischen mehrfaktoriellen Spotpreismodell bewertet. Hieran schließt sich die Vorstellung der Bewertung sowie des Hedgings gegen{\"u}ber der Forwardcurve an. Abschließend erfolgt eine vergleichende Gegen{\"u}berstellung beider Verfahren.},
  language  = {de}
}
@article{BorchertHasenbeck2009,
  author    = {Borchert, J{\"o}rg and Hasenbeck, Marc},
  title     = {Bewertung und Steuerung von Kraftwerksscheiben},
  series = {Zeitschrift f{\"u}r Energiewirtschaft},
  volume    = {33},
  journal   = {Zeitschrift f{\"u}r Energiewirtschaft},
  number    = {2},
  publisher = {Vieweg},
  address   = {Wiesbaden},
  issn      = {1866-2765},
  doi       = {10.1007/s12398-009-0014-0},
  pages     = {115 -- 126},
  year      = {2009},
  language  = {de}
}
@article{BorchertSchemm2007,
  author    = {Borchert, J{\"o}rg and Schemm, R.},
  title     = {Einsatz der Portfoliotheorie im Asset Allokations-Prozess am Beispiel eines fiktiven Anlageraumes von Windkraftstandorten},
  series = {Zeitschrift f{\"u}r Energiewirtschaft},
  volume    = {31},
  journal   = {Zeitschrift f{\"u}r Energiewirtschaft},
  number    = {4},
  issn      = {0343-5377},
  pages     = {311},
  year      = {2007},
  language  = {de}
}
@article{JungbluthBorchert2008,
  author    = {Jungbluth, Christian and Borchert, J{\"o}rg},
  title     = {M{\"o}glichkeiten der Strompreisbeeinflussung im oligopolistischen Markt},
  series = {ZNER Zeitschrift f{\"u}r Neues Energierecht},
  journal   = {ZNER Zeitschrift f{\"u}r Neues Energierecht},
  number    = {4},
  pages     = {314 -- 323},
  year      = {2008},
  language  = {de}
}
@article{WalterBorchert2002,
  author    = {Walter, G. and Borchert, J{\"o}rg},
  title     = {Der Einsatz von Realoptionen in der Elektrizit{\"a}tswirtschaft},
  series = {M \& A Review},
  journal   = {M \& A Review},
  number    = {4},
  issn      = {1616-0878},
  pages     = {198},
  year      = {2002},
  language  = {de}
}
@article{MottaghyPechnigVogt2011,
  author    = {Mottaghy, Darius and Pechnig, Renate and Vogt, Christian},
  title     = {The geothermal project Den Haag: 3D numerical models for temperature prediction and reservoir simulation},
  series = {Geothermics},
  volume    = {40},
  journal   = {Geothermics},
  number    = {3},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0375-6505},
  doi       = {10.1016/j.geothermics.2011.07.001},
  pages     = {199 -- 210},
  year      = {2011},
  abstract  = {The proposed Den Haag Zuidwest district heating system of the city of The Hague consists of a deep doublet in a Jurassic sandstone layer that is designed for a production temperature of 75 °C and a reinjection temperature of 40 °C at a flow rate of 150 m3 h-1. The prediction of reservoir temperature and production behavior is crucial for success of the proposed geothermal doublet. This work presents the results of a study of the important geothermal and geohydrological issues for the doublet design. In the first phase of the study, the influences of the three-dimensional (3D) structures of anticlines and synclines on the temperature field were examined. A comprehensive petrophysical investigation was performed to build a large scale 3D-model of the reservoir. Several bottomhole temperatures (BHTs), as well as petrophysical logs were used to calibrate the model using thermal conductivity measurements on 50 samples from boreholes in different lithological units in the study area. Profiles and cross sections extracted from the calculated temperature field were used to study the temperature in the surrounding areas of the planned doublet. In the second phase of the project, a detailed 3D numerical reservoir model was set up, with the aim of predicting the evolution of the producer and injector temperatures, and the extent of the cooled area around the injector. The temperature model from the first phase provided the boundary conditions for the reservoir model. Hydraulic parameters for the target horizons, such as porosity and permeability, were taken from data available from the nearby exploration wells. The simulation results are encouraging as no significant thermal breakthrough is predicted. For the originally planned location of the producer, the extracted water temperature is predicted to be around 79 °C, with an almost negligible cooling in the first 50 years of production. When the producer is located shallower parts of the reservoir, the yield water temperatures is lower, starting at ≈76 °C and decreasing to ≈74 °C after 50 years of operation. This comparatively larger decrease in temperature with time is caused by the structural feature of the reservoir, namely a higher dip causes the cooler water to easily move downward. In view of the poor reservoir data, the reservoir simulation model is constructed to allow iterative updates using data assimilation during planned drilling, testing, and production phases. Measurements during an 8 h pumping test carried out in late 2010 suggest that a flow rate of 150 m3 h-1 is achievable. Fluid temperatures of 76.5 °C were measured, which is very close to the predicted value.},
  language  = {en}
}
@article{KuertenMottaghyZiegler2013,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {W{\"a}rme{\"u}bergangswiderstand bei fl{\"a}chigen thermo-aktiven Bauteilen am Beispiel thermo-aktiver Abdichtungselemente},
  series = {Bautechnik},
  volume    = {90},
  journal   = {Bautechnik},
  number    = {7},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-0999},
  doi       = {10.1002/bate.201300035},
  pages     = {387 -- 394},
  year      = {2013},
  language  = {de}
}
@article{MottaghySchwambornRath2013,
  author    = {Mottaghy, Darius and Schwamborn, G. and Rath, V.},
  title     = {Past climate changes and permafrost depth at the Lake El'gygytgyn site: implications from data and thermal modeling},
  series = {Climate of the Past},
  volume    = {9},
  journal   = {Climate of the Past},
  number    = {1},
  publisher = {Copernicus},
  address   = {Katlenburg-Lindau},
  issn      = {1814-9332},
  doi       = {10.5194/cp-9-119-2013},
  pages     = {119 -- 133},
  year      = {2013},
  language  = {en}
}
@article{VogtIwanowskiStrahserMarquartetal.2013,
  author    = {Vogt, Christian and Iwanowski-Strahser, Katha and Marquart, Gabriele and Arnold, Juliane and Mottaghy, Darius and Pechnig, Renate and Gnjezda, Daniel and Clauser, Christoph},
  title     = {Modeling contribution to risk assessment of thermal production power for geothermal reservoirs},
  series = {Renewable Energy},
  volume    = {53},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.11.026},
  pages     = {230 -- 241},
  year      = {2013},
  language  = {en}
}
@article{KuertenMottaghyZiegler2014,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {Planung, Auslegung und Dimensionierung von thermo-aktiven Bauteilen am Beispiel thermo-aktiver Abdichtungselemente},
  series = {Geothermie, Bohr- und Brunnentechnik},
  journal   = {Geothermie, Bohr- und Brunnentechnik},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  pages     = {18 -- 20},
  year      = {2014},
  language  = {de}
}
@article{RathMottaghy2014,
  author    = {Rath, V. and Mottaghy, Darius},
  title     = {Klimainformation aus dem Untergrund?},
  series = {Geographische Rundschau},
  volume    = {66},
  journal   = {Geographische Rundschau},
  number    = {7-8},
  publisher = {Westermann},
  address   = {Braunschweig},
  issn      = {0016-7460},
  pages     = {30 -- 36},
  year      = {2014},
  language  = {de}
}
@article{VogtMottaghyRathetal.2014,
  author    = {Vogt, C. and Mottaghy, Darius and Rath, V. and Marquart, G. and Dijkshoorn, L. and Wolf, A. and Clauser, C.},
  title     = {Vertical variation in heat flow on the Kola Peninsula: palaeoclimate or fluid flow?},
  series = {Geophysical Journal International},
  volume    = {199},
  journal   = {Geophysical Journal International},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1365-246X},
  doi       = {10.1093/gji/ggu282},
  pages     = {829 -- 843},
  year      = {2014},
  abstract  = {Following earlier studies, we present forward and inverse simulations of heat and fluid transport of the upper crust using a local 3-D model of the Kola area. We provide best estimates for palaeotemperatures and permeabilities, their errors and their dependencies. Our results allow discriminating between the two mentioned processes to a certain extent, partly resolving the non-uniqueness of the problem. We find clear indications for a significant contribution of advective heat transport, which, in turn, imply only slightly lower ground surface temperatures during the last glacial maximum relative to the present value. These findings are consistent with the general background knowledge of (i) the fracture zones and the corresponding fluid movements in the bedrock and (ii) the glacial history of the Kola area.},
  language  = {en}
}
@article{MottaghySchellschmidtPopovetal.2005,
  author    = {Mottaghy, Darius and Schellschmidt, R. and Popov, Y. A. and Clauser, C. and Kukkonen, I. T. and Nover, G. and Milanovsky, S. and Romushkevich, R. A.},
  title     = {New heat flow data from the immediate vicinity of the Kola super-deep borehole: Vertical variation in heat flow density confirmed and attributed to advection},
  series = {Tectonophysics},
  volume    = {401},
  journal   = {Tectonophysics},
  number    = {1-2},
  issn      = {1879-3266},
  doi       = {10.1016/j.tecto.2005.03.005},
  pages     = {119 -- 142},
  year      = {2005},
  language  = {en}
}
@article{MottaghyRath2006,
  author    = {Mottaghy, Darius and Rath, Volker},
  title     = {Latent heat effects in subsurface heat transport modelling and their impact on palaeotemperature reconstructions},
  series = {Geophysical Journal International},
  volume    = {164},
  journal   = {Geophysical Journal International},
  number    = {1},
  issn      = {1365-246X},
  doi       = {10.1111/j.1365-246X.2005.02843.x},
  pages     = {236 -- 245},
  year      = {2006},
  language  = {en}
}
@article{RathMottaghy2007,
  author    = {Rath, V. and Mottaghy, Darius},
  title     = {Smooth inversion for ground surface temperature histories: estimating the optimum regularization parameter by generalized cross-validation},
  series = {Geophysical Journal International},
  volume    = {171},
  journal   = {Geophysical Journal International},
  number    = {3},
  issn      = {1365-246X},
  doi       = {10.1111/j.1365-246X.2007.03587.x},
  pages     = {1440 -- 1448},
  year      = {2007},
  language  = {en}
}
@article{BaierMottaghyZiegleretal.2008,
  author    = {Baier, C. and Mottaghy, Darius and Ziegler, M. and Rath, V.},
  title     = {Numerische Simulation des Gefrierprozesses bei der Baugrundvereisung im durchstr{\"o}mten Untergrund},
  series = {Bauingenieur},
  volume    = {83},
  journal   = {Bauingenieur},
  number    = {2},
  issn      = {0005-6650},
  pages     = {49 -- 60},
  year      = {2008},
  language  = {de}
}
@article{MottaghyVosteenSchellschmidt2008,
  author    = {Mottaghy, Darius and Vosteen, Hans-Dieter and Schellschmidt, R{\"u}diger},
  title     = {Temperature dependence of the relationship of thermal diffusivity versus thermal conductivity for crystalline rocks},
  series = {International Journal of Earth Sciences},
  volume    = {97},
  journal   = {International Journal of Earth Sciences},
  number    = {2},
  issn      = {1437-3262},
  doi       = {10.1007/s00531-007-0238-3},
  pages     = {435 -- 442},
  year      = {2008},
  language  = {en}
}
@article{MottaghyPechnig2009,
  author    = {Mottaghy, Darius and Pechnig, Renate},
  title     = {Numerische 3D Modelle zur Temperaturvorhersage und Reservoirsimulationen},
  series = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau},
  volume    = {60},
  journal   = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau},
  number    = {10},
  pages     = {44 -- 51},
  year      = {2009},
  language  = {de}
}
@article{BergAngererMartinellietal.2013,
  author    = {Berg, Milena and Angerer, Anita and Martinelli, Walter and Hammer, Stephan and Mottaghy, Darius},
  title     = {Erkundung des geothermischen Potenzials eines ehemaligen Untertagebergbaus},
  series = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau},
  volume    = {64},
  journal   = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau},
  number    = {6},
  pages     = {46 -- 52},
  year      = {2013},
  language  = {de}
}
@article{ChenClauserMarquartetal.2015,
  author    = {Chen, Tao and Clauser, Christoph and Marquart, Gabriele and Willbrand, Karen and Mottaghy, Darius},
  title     = {A new upscaling method for fractured porous media},
  series = {Advances in Water Resources},
  volume    = {80},
  journal   = {Advances in Water Resources},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0309-1708},
  doi       = {10.1016/j.advwatres.2015.03.009},
  pages     = {60 -- 68},
  year      = {2015},
  language  = {en}
}
@article{KuertenMottaghyZiegler2015,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {A new model for the description of the heat transfer for plane thermo-active geotechnical systems based on thermal resistances},
  series = {Acta Geotechnica},
  volume    = {10},
  journal   = {Acta Geotechnica},
  number    = {2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1861-1133},
  doi       = {10.1007/s11440-014-0311-6},
  pages     = {219 -- 229},
  year      = {2015},
  language  = {en}
}
@article{KuertenMottaghyZiegler2015,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {Design of plane energy geostructures based on laboratory tests and numerical modelling},
  series = {Energy and Buildings},
  volume    = {107},
  journal   = {Energy and Buildings},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0378-7788},
  doi       = {10.1016/j.enbuild.2015.08.039},
  pages     = {434 -- 444},
  year      = {2015},
  language  = {en}
}
@article{KuertenMottaghyZiegler2015,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {Besonderheiten bei der Planung und Berechnung von oberfl{\"a}chennahen thermo-aktiven Bauteilen},
  series = {Geotechnik},
  volume    = {38},
  journal   = {Geotechnik},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2190-6653},
  doi       = {10.1002/gete.201500002},
  pages     = {107 -- 119},
  year      = {2015},
  language  = {de}
}
@article{MistlerButenwegMeskouris2006,
  author    = {Mistler, Michael and Butenweg, Christoph and Meskouris, Konstantin},
  title     = {Modelling methods of historic masonry buildings under seismic excitation},
  series = {Journal of seismology},
  volume    = {Volume 10},
  journal   = {Journal of seismology},
  number    = {No. 4},
  issn      = {1383-4649 (Print) ; 1573-157X (E-Journal)},
  doi       = {10.1007/s10950-006-9033-z},
  pages     = {497 -- 510},
  year      = {2006},
  language  = {en}
}
@article{MeskourisButenwegRenault2006,
  author    = {Meskouris, Konstantin and Butenweg, Christoph and Renault, Philippe},
  title     = {Beurteilung der Erdbebensicherheit von bestehenden Bauwerken},
  series = {Der Pr{\"u}fingenieur : das Magazin der Bundesvereinigung der Pr{\"u}fingenieure f{\"u}r Bautechnik},
  journal   = {Der Pr{\"u}fingenieur : das Magazin der Bundesvereinigung der Pr{\"u}fingenieure f{\"u}r Bautechnik},
  number    = {Ausgabe 28},
  issn      = {1430-9084},
  pages     = {56 -- 65},
  year      = {2006},
  language  = {de}
}
@article{MistlerAnthoineButenweg2007,
  author    = {Mistler, Michael and Anthoine, A. and Butenweg, Christoph},
  title     = {In-plane and out-of-plane homogenisation of masonry},
  series = {Computers \& structures},
  volume    = {Volume 85},
  journal   = {Computers \& structures},
  number    = {Issues 17-18},
  issn      = {1879-2243 (E-Journal); 0045-7949 (Print)},
  doi       = {10.1016/j.compstruc.2006.08.087},
  pages     = {1321 -- 1330},
  year      = {2007},
  language  = {en}
}
@article{RochefortVerverGrunendahletal.2005,
  author    = {Rochefort, E. de and Verver, M. and Grunendahl, A. and Mooi, H. and Butenweg, Christoph},
  title     = {Detailed modelling of the lumbar spine for investigations of low back pain},
  series = {SAE transactions : papers presented at Society and Section meetings / Society of Automotive Engineers},
  volume    = {Volume 114},
  journal   = {SAE transactions : papers presented at Society and Section meetings / Society of Automotive Engineers},
  number    = {Part 7},
  organization    = {Society of Automotive Engineers},
  issn      = {0096-736X},
  pages     = {788 -- 796},
  year      = {2005},
  language  = {en}
}
@article{MeskourisButenwegGellert2009,
  author    = {Meskouris, Konstantin and Butenweg, Christoph and Gellert, Christoph},
  title     = {Iterativ verbessert : die RWTH Aachen entwickelt eine Software f{\"u}r einfache Nachweise von Mauerwerksbauten in Erdbebengebieten},
  series = {Deutsches Ingenieur-Blatt : Ingenieurwesen, Bautechnik, Umweltschutz ; Organ der deutschen Ingenieurkammern / Hrsg.: Bundes-Ingenieurkammer e.V.},
  journal   = {Deutsches Ingenieur-Blatt : Ingenieurwesen, Bautechnik, Umweltschutz ; Organ der deutschen Ingenieurkammern / Hrsg.: Bundes-Ingenieurkammer e.V.},
  number    = {Heft 5},
  publisher = {Rauh Medien GmbH},
  address   = {Wandlitz},
  issn      = {2365-192X},
  pages     = {31 -- 36},
  year      = {2009},
  language  = {de}
}
@article{KuhlmannButenwegBettzieche2006,
  author    = {Kuhlmann, Wolfram and Butenweg, Christoph and Bettzieche, Volker},
  title     = {Experimentelle und numerische Untersuchungen zur baudynamischen Beurteilung von Talsperren},
  series = {Wasserwirtschaft : Hydrologie, Wasserbau, Hydromechanik, Gew{\"a}sser, {\"O}kologie, Boden},
  volume    = {Band 96},
  journal   = {Wasserwirtschaft : Hydrologie, Wasserbau, Hydromechanik, Gew{\"a}sser, {\"O}kologie, Boden},
  number    = {Heft 5},
  issn      = {0043-0978 (E-Journal); 0043-0978 (Print)},
  pages     = {10 -- 16},
  year      = {2006},
  language  = {de}
}
@article{MeskourisButenwegRenault2006,
  author    = {Meskouris, Konstantin and Butenweg, Christoph and Renault, Philippe},
  title     = {Mehrstufen-Konzept f{\"u}r mehr Erdbebensicherheit : ein Werkzeug f{\"u}r die Beurteilung der Erdbebengef{\"a}hrdung von Ingenieurbauwerken},
  series = {Deutsches Ingenieurblatt},
  volume    = {Band 13},
  journal   = {Deutsches Ingenieurblatt},
  number    = {Heft 6},
  issn      = {0946-2422},
  pages     = {18 -- 26},
  year      = {2006},
  language  = {de}
}
@article{MistlerButenwegFehlingetal.2007,
  author    = {Mistler, Michael and Butenweg, Christoph and Fehling, Ekkehard and St{\"u}rz, Jochen},
  title     = {Verformungsbasierte seismische Bemessung von Mauerwerksbauten auf Grundlage zyklischer Schubwandversuche},
  series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  volume    = {Band 82},
  journal   = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  issn      = {1434-6591},
  pages     = {S3 -- S11},
  year      = {2007},
  language  = {de}
}
@article{GoemmelButenwegBolenderetal.2007,
  author    = {G{\"o}mmel, Andreas and Butenweg, Christoph and Bolender, Katrin and Grunendahl, Arno},
  title     = {A muscle controlled finite-element model of laryngeal abduction and adduction},
  series = {Computer methods in biomechanics and biomedical engineering},
  volume    = {Volume 10},
  journal   = {Computer methods in biomechanics and biomedical engineering},
  number    = {Issue 5},
  issn      = {1476-8259 (E-Journal); 1025-5842 (Print)},
  pages     = {377 -- 388},
  year      = {2007},
  language  = {en}
}
@article{ButenwegGellert2012,
  author    = {Butenweg, Christoph and Gellert, Christoph},
  title     = {Integrale Geb{\"a}udeplanung am Beispiel eines Geschossbaus in Ziegelmauerwerk},
  series = {Mauerwerk : European journal of masonry},
  volume    = {Volume 16},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {5},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201200550},
  pages     = {247 -- 254},
  year      = {2012},
  abstract  = {Moderne Mauerwerksbauten m{\"u}ssen nach heutigen Anforderungen architektonisch, statisch, energetisch sowie schall- und brandschutztechnisch optimal ausgelegt sein. Aufgrund der Komplexit{\"a}t und engen Verzahnung der einzelnen Anforderungen ist eine integrale Geb{\"a}udeplanung zur Erzielung einer qualitativ hochwertigen Bauwerksl{\"o}sung unbedingt notwendig. Diese erfordert von den Fachplanern vertieftes Spezialwissen in den verschiedenen Bereichen, um insbesondere die Schnittstellen und Bauwerksdetails korrekt zu planen und auszuf{\"u}hren. Der Beitrag stellt die integrale Geb{\"a}udeplanung am Beispiel eines Geschossbaus in Ziegelbauweise mit L{\"o}sungen f{\"u}r wesentliche Detailpunkte vor},
  language  = {de}
}
@article{EdipGarevskiButenwegetal.2013,
  author    = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sesov, Vlatko and Cvetanovska, Julijana and Gjorgiev, Igor},
  title     = {Numerical simulation of geotechnical problems by coupled finite and infinite elements},
  series = {Journal of civil engineering and architecture},
  volume    = {7},
  journal   = {Journal of civil engineering and architecture},
  number    = {1},
  publisher = {David Publishing},
  address   = {Libertyville},
  issn      = {1934-7359 (E-Journal)},
  pages     = {68 -- 77},
  year      = {2013},
  language  = {en}
}
@article{ButenwegKleemannIkier2013,
  author    = {Butenweg, Christoph and Kleemann, Anne and Ikier, Axel},
  title     = {Impact-Belastungen von Stahlbetonkonstruktionen},
  series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  volume    = {Band 88},
  journal   = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  publisher = {VDI Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {0005-6650},
  pages     = {S7 -- S14},
  year      = {2013},
  language  = {de}
}
@article{ButenwegGellert2013,
  author    = {Butenweg, Christoph and Gellert, Christoph},
  title     = {Nichtlinearer Nachweis von Mauerwerksbauten},
  series = {Mauerwerk : European journal of masonry},
  volume    = {Volume 17},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {Issue 3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201300575},
  pages     = {166 -- 171},
  year      = {2013},
  language  = {de}
}
@article{AltayButenwegTaddei2013,
  author    = {Altay, Okyay and Butenweg, Christoph and Taddei, Francesca},
  title     = {Effektivit{\"a}t von Schwingungsd{\"a}mpfern bei Windenergieanlagen},
  series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  volume    = {Band 88},
  journal   = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  number    = {Heft 10},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {1436-4867 (E-Journal); 0005-6650 (Print)},
  pages     = {S11 -- S17},
  year      = {2013},
  language  = {de}
}
@article{TaddeiButenwegKlinkel2015,
  author    = {Taddei, Francesca and Butenweg, Christoph and Klinkel, S.},
  title     = {Parametric investigation of the soil-structure interaction effects on the dynamic behaviour of a shallow foundation supported wind turbine considering a layered soil},
  series = {Wind energy : an international journal for progress and applications in wind power conversion technology},
  volume    = {Volume 18},
  journal   = {Wind energy : an international journal for progress and applications in wind power conversion technology},
  number    = {Issue 3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1099-1824 (E-Journal); 1095-4244 (Print)},
  doi       = {10.1002/we.1703},
  pages     = {399 -- 417},
  year      = {2015},
  language  = {en}
}
@article{GellertButenweg2014,
  author    = {Gellert, Christoph and Butenweg, Christoph},
  title     = {Seismic analysis of masonry structures in German earthquake zones according to DIN EN 1998-1},
  series = {Mauerwerk : European journal of masonry},
  volume    = {18},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {3-4},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201400626},
  pages     = {188 -- 196},
  year      = {2014},
  abstract  = {Die Erdbeben in Albstadt 1978 (Magnitude 5,7), Roermond 1992 (Magnitude 5,9) oder in Waldkirch 2004 (Magnitude 5,1) haben verdeutlicht, dass die erdbebensichere Auslegung von Mauerwerksbauten auch in Deutschland von großer Bedeutung ist. Bereits im Jahr 1981 wurde die DIN 4149 (1981) "Bauten in deutschen Erdbebengebieten - Lastannahmen, Bemessung und Ausf{\"u}hrung {\"u}blicher Hochbauten" eingef{\"u}hrt, in der aber f{\"u}r Mauerwerksbauten nur wenige Anforderungen gestellt wurden. Diese Norm wurde durch den NABau-Arbeitsausschuss "Erdbeben; Sonderfragen" des Deutschen Instituts f{\"u}r Normung e.V. (DIN) auf Grundlage des Eurocode 8 (2004) vollst{\"a}ndig {\"u}berarbeitet und durch die DIN 4149 (2005) abgel{\"o}st, die umfangreiche Regelungen f{\"u}r die seismische Auslegung von Mauerwerksbauten enth{\"a}lt. Mittlerweile liegen die DIN EN 1998-1 (2010) und der Nationale Anhang DIN EN 1998-1/NA (2011) vor, die nach Einarbeitung der Ergebnisse der durchgef{\"u}hrten Anwendungserprobung bauaufsichtlich eingef{\"u}hrt und die DIN 4149 (2005) ersetzen werden. Der folgende Beitrag gibt einen {\"U}berblick {\"u}ber die seismische Berechnung und Bemessung von Mauerwerksbauten nach dem europ{\"a}ischen Regelwerk und illustriert deren Anwendung an einem baupraktischen Beispiel.},
  language  = {de}
}