@article{FunkeDickhoffKeinzetal.2014,
  author    = {Funke, Harald and Dickhoff, J. and Keinz, Jan and Anis, H. A. and Parente, A. and Hendrick, P.},
  title     = {Experimental and numerical study of the micromix combustion principle applied for hydrogen and hydrogen-rich syngas as fuel with increased energy density for industrial gas turbine applications},
  series = {Energy procedia},
  journal   = {Energy procedia},
  number    = {61},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102 (E-Journal)},
  doi       = {10.1016/j.egypro.2014.12.201},
  pages     = {1736 -- 1739},
  year      = {2014},
  abstract  = {The Dry Low NOx (DLN) Micromix combustion principle with increased energy density is adapted for the industrial gas turbine APU GTCP 36-300 using hydrogen and hydrogen-rich syngas with a composition of 90\%-Vol. hydrogen (H₂) and 10\%-Vol. carbon-monoxide (CO). Experimental and numerical studies of several combustor geometries for hydrogen and syngas show the successful advance of the DLN Micromix combustion from pure hydrogen to hydrogen-rich syngas. The impact of the different fuel properties on the combustion principle and aerodynamic flame stabilization design laws, flow field, flame structure and emission characteristics is investigated by numerical analysis using a hybrid Eddy Break Up combustion model and validated against experimental results.},
  language  = {en}
}
@article{OberlaenderKirchnerBoyenetal.2014,
  author    = {Oberl{\"a}nder, Jan and Kirchner, Patrick and Boyen, Hans-Gerd and Sch{\"o}ning, Michael Josef},
  title     = {Detection of hydrogen peroxide vapor by use of manganese(IV) oxide as catalyst for calorimetric gas sensors},
  series = {Physica status solidi A: Applications and materials science},
  volume    = {211},
  journal   = {Physica status solidi A: Applications and materials science},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-396X (E-Journal); 1862-6319 (E-Journal); 0031-8965 (Print); 1862-6300 (Print)},
  doi       = {10.1002/pssa.201330359},
  pages     = {1372 -- 1376},
  year      = {2014},
  abstract  = {In this work, the catalyst manganese(IV) oxide (MnO2), of calorimetric gas sensors (to monitor the sterilization agent vaporized hydrogen peroxide) has been investigated in more detail. Chemical analyses by means of X-ray-induced photoelectron spectroscopy have been performed to unravel the surface chemistry prior and after exposure to hydrogen peroxide vapor at elevated temperature, as applied in the sterilization processes of beverage cartons. The surface characterization reveals a change in oxidation states of the metal oxide catalyst after exposure to hydrogen peroxide. Additionally, a cleaning effect of the catalyst, which itself is attached to the sensor surface by means of a polymer interlayer, could be observed.},
  language  = {en}
}
@article{Frings2014,
  author    = {Frings, Michael},
  title     = {Das Gesetz gegen unseri{\"o}se Gesch{\"a}ftspraktiken},
  series = {NWB : NWB Steuer- und Wirtschaftsrecht},
  journal   = {NWB : NWB Steuer- und Wirtschaftsrecht},
  number    = {11},
  publisher = {NWB-Verlag},
  address   = {Herne},
  issn      = {0028-3460 (Print)},
  pages     = {769 -- 775},
  year      = {2014},
  language  = {de}
}
@article{Frings2014,
  author    = {Frings, Michael},
  title     = {Neuregelung des Verbraucherschutzes - Umsetzung der EU-Verbraucherrechterichtlinie},
  series = {NWB : NWB Steuer- und Wirtschaftsrecht},
  journal   = {NWB : NWB Steuer- und Wirtschaftsrecht},
  number    = {14},
  publisher = {NWB-Verlag},
  address   = {Herne},
  issn      = {0028-3460 (Print)},
  pages     = {1003 -- 1018},
  year      = {2014},
  language  = {de}
}
@article{FuestKotliarWalteretal.2014,
  author    = {Fuest, Matthias and Kotliar, Konstantin and Walter, Peter and Plange, Niklas},
  title     = {Monitoring intraocular pressure changes after intravitreal Ranibizumab injection using rebound tonometry},
  series = {Ophthalmic and physiological optics},
  volume    = {34},
  journal   = {Ophthalmic and physiological optics},
  number    = {4},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1475-1313 (E-Journal); 0275-5408 (Print)},
  doi       = {10.1111/opo.12134},
  pages     = {438 -- 444},
  year      = {2014},
  language  = {en}
}
@article{GuoMiyamotoWagneretal.2014,
  author    = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Theoretical study and simulation of light-addressable potentiometric sensors},
  series = {Physica status solidi (A) : applications and materials},
  volume    = {211},
  journal   = {Physica status solidi (A) : applications and materials},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0031-8965},
  doi       = {10.1002/pssa.201330354},
  pages     = {1467 -- 1472},
  year      = {2014},
  abstract  = {The light-addressable potentiometric sensor (LAPS) is a semiconductor-based potentiometric sensor using a light probe with an ability of detecting the concentration of biochemical species in a spatially resolved manner. As an important biomedical sensor, research has been conducted to improve its performance, for instance, to realize high-speed measurement. In this work, the idea of facilitating the device-level simulation, instead of using an equivalent-circuit model, is presented for detailed analysis and optimization of the performance of the LAPS. Both carrier distribution and photocurrent response have been simulated to provide new insight into both amplitude-mode and phase-mode operations of the LAPS. Various device parameters can be examined to effectively design and optimize the LAPS structures and setups for enhanced performance.},
  language  = {en}
}
@article{SchirraWatmuffBauschat2014,
  author    = {Schirra, Julian and Watmuff, Jonathan and Bauschat, J.-Michael},
  title     = {Highly non-planar lifting systems: a relative assessment of existing potential-methodologies to accurately estimate the induced drag},
  series = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.},
  journal   = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.},
  organization    = {American Institute of Aeronautics and Astronautics},
  isbn      = {978-1-62410-288-2},
  doi       = {10.2514/6.2014-2988},
  pages     = {Publ. online},
  year      = {2014},
  language  = {en}
}
@article{RiedelKartchemnikSchoeningetal.2014,
  author    = {Riedel, Marc and Kartchemnik, Julia and Sch{\"o}ning, Michael Josef and Lisdat, Fred},
  title     = {Impedimetric DNA detection - steps forward to sensorial application},
  series = {Analytical chemistry},
  volume    = {86 (2014)},
  journal   = {Analytical chemistry},
  number    = {15},
  publisher = {ACS Publications},
  address   = {Columbus},
  issn      = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)},
  doi       = {10.1021/ac501800q},
  pages     = {7867 -- 7874},
  year      = {2014},
  abstract  = {This study describes a label-free impedimetric sensor based on short ssDNA recognition elements for the detection of hybridization events. We concentrate on the elucidation of the influence of target length and recognition sequence position on the sensorial performance. The impedimetric measurements are performed in the presence of the redox system ferri-/ferrocyanide and show an increase in charge transfer resistance upon hybridization of ssDNA to the sensor surface. Investigations on the impedimetric signal stability demonstrate a clear influence of the buffers used during the sensor preparation and the choice of the passivating mercaptoalcanol compound. A stable sensor system has been developed, enabling a reproducible detection of 25mer target DNA in the low nanomolar range. After hybridization, a sensor regeneration can be reached with deionized water by adjustment of effective convection conditions, ensuring a sensor reusability. By investigations of longer targets with overhangs exposed to the solution, we can demonstrate applicability of the impedimetric detection for longer ssDNA. However, a decreasing charge transfer resistance change (ΔRct) is found by extending the overhang. As a strategy to increase the impedance change for longer target strands, the position of the recognition sequence can be designed in a way that a small overhang is exposed to the electrode surface. This is found to result in an increase in the relative Rct change. These results suggest that DNA and consequently negative charge near the electrode possess a larger impact on the impedimetric signal than DNA further away.},
  language  = {en}
}
@article{GebhardtFateri2014,
  author    = {Gebhardt, Andreas and Fateri, Miranda},
  title     = {3D-Drucken und die Anwendungen},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {11 (2014)},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  number    = {1},
  issn      = {1614-0923},
  pages     = {1 -- 9},
  year      = {2014},
  language  = {de}
}
@article{GebhardtHoetterZiebura2014,
  author    = {Gebhardt, Andreas and H{\"o}tter, Jan-Steffen and Ziebura, Dawid},
  title     = {Impact of SLM build parameters on the surface quality},
  series = {RTejournal - Forum f{\"u}r Rapid Technologien},
  volume    = {11 (2014)},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologien},
  number    = {1},
  issn      = {1614-0923},
  pages     = {1 -- 14},
  year      = {2014},
  language  = {de}
}
@article{AlebouyehSamamiPieperBreitbachetal.2014,
  author    = {Alebouyeh Samami, Behzad and Pieper, Martin and Breitbach, Gerd and Hodapp, Josef},
  title     = {Heat production in the windings of the stators of electric machines under stationary condition},
  series = {Heat and mass transfer},
  volume    = {50},
  journal   = {Heat and mass transfer},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {0947-7411 (Print) ; 1432-1181 (E-Journal)},
  doi       = {10.1007/s00231-014-1371-8},
  pages     = {1707 -- 1716},
  year      = {2014},
  abstract  = {In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results.},
  language  = {en}
}
@article{GuoSekiMiyamotoetal.2014,
  author    = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Novel photoexcitation method for light-addressable potentiometric sensor with higher spatial resolution},
  series = {Applied physics express : APEX},
  volume    = {7},
  journal   = {Applied physics express : APEX},
  number    = {6},
  publisher = {IOP},
  address   = {Bristol},
  issn      = {1882-0786 (E-Journa); 1882-0778 (Print)},
  doi       = {10.7567/APEX.7.067301},
  pages     = {067301-4},
  year      = {2014},
  abstract  = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) is proposed to achieve a higher spatial resolution of chemical images. The proposed method employs a combined light source that consists of a modulated light probe, which generates the alternating photocurrent signal, and a ring of constant illumination surrounding it. The constant illumination generates a sheath of carriers with increased concentration which suppresses the spread of photocarriers by enhanced recombination. A device simulation was carried out to verify the effect of constant illumination on the spatial resolution, which demonstrated that a higher spatial resolution can be obtained.},
  language  = {en}
}
@article{WhiteheadOehlschlaegerAlmajhdietal.2014,
  author    = {Whitehead, Mark and {\"O}hlschl{\"a}ger, Peter and Almajhdi, Fahad N. and Alloza, Leonor and Marz{\´a}bal, Pablo and Meyers, Ann E. and Hitzeroth, Inga I. and Rybicki, Edward P.},
  title     = {Human papillomavirus (HPV) type 16 E7 protein bodies cause tumour regression in mice},
  series = {BMC cancer},
  journal   = {BMC cancer},
  number    = {14:367},
  publisher = {BioMed Central},
  address   = {London},
  issn      = {1471-2407},
  doi       = {10.1186/1471-2407-14-367},
  pages     = {1 -- 15},
  year      = {2014},
  language  = {en}
}
@article{Timme2014,
  author    = {Timme, Michael},
  title     = {Wohnungseigent{\"u}mergemeinschaft - Einstimmigkeitserfordernis bei Errichtung einer Mobilfunkantenne},
  series = {Monatsschrift f{\"u}r Deutsches Recht : MDR : Zeitschrift f{\"u}r die Zivilrechts-Praxis},
  volume    = {68 (2014)},
  journal   = {Monatsschrift f{\"u}r Deutsches Recht : MDR : Zeitschrift f{\"u}r die Zivilrechts-Praxis},
  number    = {11},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {0340-1812},
  pages     = {634 -- 635},
  year      = {2014},
  abstract  = {Der BGH (BGH v. 25.1.2014 - V ZR 48/13, MDR 2014, 399) hatte dar{\"u}ber zu befinden, ob auf dem Dach eines Hauses, das im Eigentum einer Wohnungseigent{\"u}mergemeinschaft steht, auch gegen den Willen eines einzelnen Eigent{\"u}mers eine Mobilfunkantenne angebracht werden kann. Das Urteil f{\"u}hrt in das Spannungsfeld einer Abw{\"a}gung zwischen Mehrheits- und Individualinteressen innerhalb einer WEG. Insoweit betont der BGH den grunds{\"a}tzlichen Vorrang der Individualinteressen, jedenfalls soweit es um Beeintr{\"a}chtigungen geht, die verst{\"a}ndlicherweise von einem Eigent{\"u}mer abgelehnt werden k{\"o}nnen. Der BGH verlangt im Ergebnis im Zweifel eine allseitige Zustimmung. Das Urteil ist zu begr{\"u}ßen, l{\"a}sst aber f{\"u}r die Zukunft Abgrenzungsfragen offen.},
  language  = {de}
}
@article{WagnerDollSchoening2014,
  author    = {Wagner, Patrick and Doll, Theodor and Sch{\"o}ning, Michael Josef},
  title     = {Engineering of functional interfaces / Patrick Wagner ; Theodor Doll ; Michael J. Sch{\"o}ning (eds.)},
  series = {Physica status solidi (A) : Applications and materials science},
  volume    = {211},
  journal   = {Physica status solidi (A) : Applications and materials science},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-396X (E-Book); 1862-6319 (E-Book); 0031-8965 (Print); 1862-6300 (Print)},
  doi       = {10.1002/pssa.201470241},
  pages     = {1339 -- 1339},
  year      = {2014},
  language  = {en}
}
@article{RaueWambachGloeggleretal.2014,
  author    = {Raue, Markus and Wambach, M. and Gl{\"o}ggler, S. and Grefen, Dana and Kaufmann, R. and Abetz, C. and Georgopanos, P. and Handge, U. A. and Mang, Thomas and Bl{\"u}mich, B. and Abetz, V.},
  title     = {Investigation of historical hard rubber ornaments of Charles Goodyear},
  series = {Macromolecular chemistry and physics},
  volume    = {Vol. 215},
  journal   = {Macromolecular chemistry and physics},
  number    = {No. 3},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1022-1352},
  pages     = {245 -- 254},
  year      = {2014},
  language  = {en}
}
@article{HuberStreblowMuelleretal.2014,
  author    = {Huber, M. and Streblow, R. and M{\"u}ller, D. and Lange, S. and Joneleit, R. and Sefker, T. and Rau, Sebastian and Wollert, J{\"o}rg},
  title     = {Funksignal{\"u}bertragung in Luftleitungen},
  series = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik},
  volume    = {Bd. 65},
  journal   = {HLH : L{\"u}ftung, Klima, Heizung, Sanit{\"a}r, Geb{\"a}udetechnik},
  number    = {H. 7/8},
  issn      = {1436-5103},
  pages     = {36 -- 40},
  year      = {2014},
  language  = {de}
}
@article{KuertenMottaghyZiegler2014,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {Planung, Auslegung und Dimensionierung von thermo-aktiven Bauteilen am Beispiel thermo-aktiver Abdichtungselemente},
  series = {Geothermie, Bohr- und Brunnentechnik},
  journal   = {Geothermie, Bohr- und Brunnentechnik},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  pages     = {18 -- 20},
  year      = {2014},
  language  = {de}
}
@article{RathMottaghy2014,
  author    = {Rath, V. and Mottaghy, Darius},
  title     = {Klimainformation aus dem Untergrund?},
  series = {Geographische Rundschau},
  volume    = {66},
  journal   = {Geographische Rundschau},
  number    = {7-8},
  publisher = {Westermann},
  address   = {Braunschweig},
  issn      = {0016-7460},
  pages     = {30 -- 36},
  year      = {2014},
  language  = {de}
}
@article{VogtMottaghyRathetal.2014,
  author    = {Vogt, C. and Mottaghy, Darius and Rath, V. and Marquart, G. and Dijkshoorn, L. and Wolf, A. and Clauser, C.},
  title     = {Vertical variation in heat flow on the Kola Peninsula: palaeoclimate or fluid flow?},
  series = {Geophysical Journal International},
  volume    = {199},
  journal   = {Geophysical Journal International},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1365-246X},
  doi       = {10.1093/gji/ggu282},
  pages     = {829 -- 843},
  year      = {2014},
  abstract  = {Following earlier studies, we present forward and inverse simulations of heat and fluid transport of the upper crust using a local 3-D model of the Kola area. We provide best estimates for palaeotemperatures and permeabilities, their errors and their dependencies. Our results allow discriminating between the two mentioned processes to a certain extent, partly resolving the non-uniqueness of the problem. We find clear indications for a significant contribution of advective heat transport, which, in turn, imply only slightly lower ground surface temperatures during the last glacial maximum relative to the present value. These findings are consistent with the general background knowledge of (i) the fracture zones and the corresponding fluid movements in the bedrock and (ii) the glacial history of the Kola area.},
  language  = {en}
}
@article{LindEllrich2014,
  author    = {Lind, Thorsten Patric and Ellrich, Thomas},
  title     = {Zur Haftung der Gl{\"a}ubigerausschussmitglieder wegen unzureichender Kassenpr{\"u}fung},
  series = {Der Betrieb},
  volume    = {67},
  journal   = {Der Betrieb},
  number    = {49},
  publisher = {Fachmedien Otto Schmidt},
  address   = {D{\"u}sseldorf},
  issn      = {0005-9935},
  pages     = {2819 -- 2820},
  year      = {2014},
  language  = {de}
}
@article{MiyamotoItabashiWagneretal.2014,
  author    = {Miyamoto, Ko-ichiro and Itabashi, Akinori and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {High-speed chemical imaging inside a microfluidic channel},
  series = {Sensors and actuators. B: Chemical},
  volume    = {194},
  journal   = {Sensors and actuators. B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2013.12.090},
  pages     = {521 -- 527},
  year      = {2014},
  abstract  = {In this study, a high-speed chemical imaging system was developed for visualization of the interior of a microfluidic channel. A microfluidic channel was constructed on the sensor surface of the light-addressable potentiometric sensor (LAPS), on which the ion concentrations could be measured in parallel at up to 64 points illuminated by optical fibers. The temporal change of pH distribution inside the microfluidic channel was recorded at a maximum rate of 100 frames per second (fps). The high frame rate allowed visualization of moving interfaces and plugs in the channel even at a flow velocity of 111 mm/s, which suggests the feasibility of plug-based microfluidic devices for flow-injection analysis (FIA).},
  language  = {en}
}
@article{GoedhuysJanzMohnen2014,
  author    = {Goedhuys, Micheline and Janz, Norbert and Mohnen, Pierre},
  title     = {Knowledge-based productivity in "low-tech" industries: evidence from firms in developing countries},
  series = {Industrial and corporate change},
  volume    = {23},
  journal   = {Industrial and corporate change},
  number    = {1},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1464-3650 (E-Journal); 0960-6491 (Print)},
  doi       = {10.1093/icc/dtt006},
  pages     = {1 -- 23},
  year      = {2014},
  abstract  = {Using firm-level data from five developing countries—Brazil, Ecuador, South Africa, Tanzania, and Bangladesh—and three industries—food processing, textiles, and the garments and leather products—this article examines the importance of various sources of knowledge for explaining productivity and formally tests whether sector- or country-specific characteristics dominate these relationships. Knowledge sources driving productivity appear mainly sector specific. Also differences in the level of development affect the effectiveness of knowledge sources. In the food processing sector, firms with higher educated managers are more productive, and in least-developed countries, additionally those with technology licenses and imported machinery and equipment. In the capital-intensive textiles sector, productivity is higher in firms that conduct R\&D. In the garments and leather products sector, higher education of the managers, licensing, and R\&D raise productivity.},
  language  = {en}
}
@article{Timme2014,
  author    = {Timme, Michael},
  title     = {BGH: Geltendmachung von Sachm{\"a}ngeln bei Wohnungseigentum},
  series = {LMK : Fachdienst Zivilrecht : Kommentierte BGH-Rechtsprechung},
  volume    = {2014},
  journal   = {LMK : Fachdienst Zivilrecht : Kommentierte BGH-Rechtsprechung},
  number    = {5},
  publisher = {Beck},
  address   = {M{\"u}nchen},
  issn      = {1611-1095},
  year      = {2014},
  language  = {de}
}
@article{FiedlerHennMelcher2014,
  author    = {Fiedler, Gerda and Henn, Gudrun and Melcher, Karin},
  title     = {ANPAK - ein semesterbegleitender Anpassungskurs},
  series = {Zeitschrift f{\"u}r Hochschulentwicklung},
  volume    = {9},
  journal   = {Zeitschrift f{\"u}r Hochschulentwicklung},
  number    = {4},
  publisher = {{\"O}GHD},
  address   = {Wien},
  issn      = {2219-6994},
  pages     = {85 -- 100},
  year      = {2014},
  abstract  = {In Folge mehrj{\"a}hriger statistischer Untersuchungen an der FH Aachen ist unter anderem ein Eingangstest entstanden, der als Diagnosetool f{\"u}r einen erfolgreichen Studieneinstieg verwendet wird. Es hat sich herausgestellt, dass ein Testergebnis von weniger als 25 (von maximal 56 erreichbaren) Punkten die Chance auf einen erfolgreichen Studieneinstieg deutlich verringert. Ungef{\"a}hr die H{\"a}lfte aller Erstsemester hat weniger als 25 Punkte im Eingangstest. Weniger als 20 \% dieser Gruppe bestehen innerhalb eines Jahres die Klausur Mathematik 1. Die investierte Zeit von zwei Semestern ist mit Blick auf den Wissenszuwachs und damit letztendlich den Studienerfolg nicht effizient genutzt. Deshalb haben wir im WS 2013/14 einen semesterbegleitenden Anpassungskurs f{\"u}r diese Gruppe installiert. Ziel eines solchen Kurses ist es, die Student/innen innerhalb eines Jahres in die Lage zu versetzen, nach zwei Semestern problemlos den Vorlesungen in Mathematik zu folgen. Dieser Artikel beschreibt das Konzept dieses Anpassungskurses und zeigt erste Ergebnisse und Probleme des Pilotdurchgangs auf.},
  language  = {de}
}
@article{NachtrodtTietschMostaccietal.2014,
  author    = {Nachtrodt, Frederik and Tietsch, Wolfgang and Mostacci, Domiziano and Scherer, Ulrich W.},
  title     = {Set-up and first operation of a plasma oven for treatment of low level radioactive wastes},
  series = {Nuclear technology and radiation protection},
  volume    = {29},
  journal   = {Nuclear technology and radiation protection},
  number    = {Suppl.},
  publisher = {VINČA Institute of Nuclear Sciences},
  address   = {Belgrad},
  issn      = {1451-3994},
  doi       = {10.2298/NTRP140SS47N},
  pages     = {47 -- 51},
  year      = {2014},
  language  = {en}
}
@article{SrivastavaLahiriMaitietal.2014,
  author    = {Srivastava, A. and Lahiri, S. and Maiti, M. and Knolle, F. and Hoyler, Friedrich and Scherer, Ulrich W. and Schnug, E. W.},
  title     = {Study of naturally occurring radioactive material (NORM) in top soil of Punjab State from the North Western part of India},
  series = {Journal of Radioanalytical and Nuclear Chemistry},
  volume    = {2014},
  journal   = {Journal of Radioanalytical and Nuclear Chemistry},
  number    = {302},
  publisher = {Springer Nature},
  address   = {Basel},
  issn      = {1588-2780 (E-Journal); 0022-4081 (Print); 0134-0719 (Print); 0236-5731 (Print); 1417-2097 (Print)},
  doi       = {0.1007/s10967-014-3450-1},
  pages     = {1049 -- 1052},
  year      = {2014},
  language  = {en}
}
@article{SiqueiraMolinnusBegingetal.2014,
  author    = {Siqueira, Jose R. and Molinnus, Denise and Beging, Stefan and Sch{\"o}ning, Michael Josef},
  title     = {Incorporating a hybrid urease-carbon nanotubes sensitive nanofilm on capacitive field-effect sensors for urea detection},
  series = {Analytical chemistry},
  volume    = {86},
  journal   = {Analytical chemistry},
  number    = {11},
  publisher = {ACS Publications},
  address   = {Columbus},
  issn      = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)},
  doi       = {10.1021/ac500458s},
  pages     = {5370 -- 5375},
  year      = {2014},
  abstract  = {The ideal combination among biomolecules and nanomaterials is the key for reaching biosensing units with high sensitivity. The challenge, however, is to find out a stable and sensitive film architecture that can be incorporated on the sensor's surface. In this paper, we report on the benefits of incorporating a layer-by-layer (LbL) nanofilm of polyamidoamine (PAMAM) dendrimer and carbon nanotubes (CNTs) on capacitive electrolyte-insulator-semiconductor (EIS) field-effect sensors for detecting urea. Three sensor arrangements were studied in order to investigate the adequate film architecture, involving the LbL film with the enzyme urease: (i) urease immobilized directly onto a bare EIS [EIS-urease] sensor; (ii) urease atop the LbL film over the EIS [EIS-(PAMAM/CNT)-urease] sensor; and (iii) urease sandwiched between the LbL film and another CNT layer [EIS-(PAMAM/CNT)-urease-CNT]. The surface morphology of all three urea-based EIS biosensors was investigated by atomic force microscopy (AFM), while the biosensing abilities were studied by means of capacitance-voltage (C/V) and dynamic constant-capacitance (ConCap) measureaments at urea concentrations ranging from 0.1 mM to 100 mM. The EIS-urease and EIS-(PAMAM/CNT)-urease sensors showed similar sensitivity (∼18 mV/decade) and a nonregular signal behavior as the urea concentration increased. On the other hand, the EIS-(PAMAM/CNT)-urease-CNT sensor exhibited a superior output signal performance and higher sensitivity of about 33 mV/decade. The presence of the additional CNT layer was decisive to achieve a urea based EIS sensor with enhanced properties. Such sensitive architecture demonstrates that the incorporation of an adequate hybrid enzyme-nanofilm as sensing unit opens new prospects for biosensing applications using the field-effect sensor platform.},
  language  = {en}
}
@article{MuribYeapMartensetal.2014,
  author    = {Murib, Mohammed Sharif and Yeap, Weng-Siang and Martens, Daan and Bienstman, Peter and Ceuninck, Ward de and Grinsven, Bart van and Sch{\"o}ning, Michael Josef and Michiels, Luc and Haenen, Ken and Ameloot, Marcel and Serpeng{\"u}zel, Ali and Wagner, Patrick},
  title     = {Photonic detection and characterization of DNA using sapphire microspheres},
  series = {Journal of biomedical optics},
  volume    = {19},
  journal   = {Journal of biomedical optics},
  number    = {9},
  publisher = {SPIE},
  address   = {Bellingham},
  issn      = {1560-2281 (E-Journal); 1083-3668 (Print)},
  doi       = {10.1117/1.JBO.19.9.097006},
  pages     = {097006},
  year      = {2014},
  abstract  = {A microcavity-based deoxyribonucleic acid (DNA) optical biosensor is demonstrated for the first time using synthetic sapphire for the optical cavity. Transmitted and elastic scattering intensity at 1510 nm are analyzed from a sapphire microsphere (radius 500  μm, refractive index 1.77) on an optical fiber half coupler. The 0.43 nm angular mode spacing of the resonances correlates well with the optical size of the sapphire sphere. Probe DNA consisting of a 36-mer fragment was covalently immobilized on a sapphire microsphere and hybridized with a 29-mer target DNA. Whispering gallery modes (WGMs) were monitored before the sapphire was functionalized with DNA and after it was functionalized with single-stranded DNA (ssDNA) and double-stranded DNA (dsDNA). The shift in WGMs from the surface modification with DNA was measured and correlated well with the estimated thickness of the add-on DNA layer. It is shown that ssDNA is more uniformly oriented on the sapphire surface than dsDNA. In addition, it is shown that functionalization of the sapphire spherical surface with DNA does not affect the quality factor (Q≈104) of the sapphire microspheres. The use of sapphire is especially interesting because this material is chemically resilient, biocompatible, and widely used for medical implants.},
  language  = {en}
}
@article{GuoMiyamotoWagneretal.2014,
  author    = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor for the investigation of the spatial resolution},
  series = {Sensors and actuators B: Chemical},
  volume    = {204},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.08.016},
  pages     = {659 -- 665},
  year      = {2014},
  abstract  = {As a semiconductor-based electrochemical sensor, the light-addressable potentiometric sensor (LAPS) can realize two dimensional visualization of (bio-)chemical reactions at the sensor surface addressed by localized illumination. Thanks to this imaging capability, various applications in biochemical and biomedical fields are expected, for which the spatial resolution is critically significant. In this study, therefore, the spatial resolution of the LAPS was investigated in detail based on the device simulation. By calculating the spatiotemporal change of the distributions of electrons and holes inside the semiconductor layer in response to a modulated illumination, the photocurrent response as well as the spatial resolution was obtained as a function of various parameters such as the thickness of the Si substrate, the doping concentration, the wavelength and the intensity of illumination. The simulation results verified that both thinning the semiconductor substrate and increasing the doping concentration could improve the spatial resolution, which were in good agreement with known experimental results and theoretical analysis. More importantly, new findings of interests were also obtained. As for the dependence on the wavelength of illumination, it was found that the known dependence was not always the case. When the Si substrate was thick, a longer wavelength resulted in a higher spatial resolution which was known by experiments. When the Si substrate was thin, however, a longer wavelength of light resulted in a lower spatial resolution. This finding was explained as an effect of raised concentration of carriers, which reduced the thickness of the space charge region. The device simulation was found to be helpful to understand the relationship between the spatial resolution and device parameters, to understand the physics behind it, and to optimize the device structure and measurement conditions for realizing higher performance of chemical imaging systems.},
  language  = {en}
}
@article{KhaydukovaZadorozhnayaKirsanovetal.2014,
  author    = {Khaydukova, M. M. and Zadorozhnaya, O. A. and Kirsanov, D. O. and Iken, Heiko and Rolka, David and Sch{\"o}ning, Michael Josef and Babain, V. A. and Vlasov, Yu. G. and Legin, A. V.},
  title     = {Multivariate processing of atomic-force microscopy images for detection of the response of plasticized polymeric membranes},
  series = {Russian journal of applied chemistry},
  volume    = {87},
  journal   = {Russian journal of applied chemistry},
  number    = {3},
  publisher = {Springer},
  address   = {Dordrecht},
  issn      = {1608-3296 (E-Journal); 1070-4272 (Print)},
  doi       = {10.1134/S1070427214030112},
  pages     = {307 -- 314},
  year      = {2014},
  abstract  = {The possibility of using the atomic-force microscopy as a method for detection of the analytical signal from plasticized polymeric sensor membranes was analyzed. The surfaces of cadmium-selective membranes based on two polymeric matrices were examined. The digital images were processed with multivariate image analysis techniques. A correlation was found between the surface profile of an ion-selective membrane and the concentration of the ion in solution.},
  language  = {en}
}
@article{MuellerHirschfeldLambertzetal.2014,
  author    = {M{\"u}ller, Martin and Hirschfeld, Julian and Lambertz, Rita and Schulze Lohoff, Andreas and Lustfeld, Hans and Pfeifer, Heinz and Reißel, Martin},
  title     = {Validation of a novel method for detecting and stabilizing malfunctioning areas in fuel cell stacks},
  series = {Journal of power sources},
  volume    = {272},
  journal   = {Journal of power sources},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-2755 (E-Journal); 0378-7753 (Print)},
  doi       = {10.1016/j.jpowsour.2014.08.045},
  pages     = {225 -- 232},
  year      = {2014},
  abstract  = {In this paper a setup for detecting malfunctioning areas of MEAs in fuel cell stacks is described. Malfunctioning areas generate electric cross currents inside bipolar plates. To exploit this we suggest bipolar plates consisting not of two but of three layers. The third one is a highly conducting layer and segmented such that the cross currents move along the segments to the surface of the stack where they can be measured by an inductive sensor. With this information a realistic model can be used to detect the malfunctioning area. Furthermore the third layer will prevent any current inhomogeneity of a malfunctioning cell to spread to neighbouring cells in the stack. In this work the results of measurements in a realistic cell setup will be compared with the results obtained in simulation studies with the same configuration. The basis for the comparison is the reliable characterisation of the electrical properties of the cell components and the implication of these results into the simulation model. The experimental studies will also show the limits in the maximum number of segments, which can be used for a reliable detection of cross currents.},
  language  = {en}
}
@article{StadlerGarveyEmbsetal.2014,
  author    = {Stadler, Alexander Maximilian and Garvey, Christopher J. and Embs, Jan Peter and Koza, Michael Marek and Unruh, Tobias and Artmann, Gerhard and Zaccai, Guiseppe},
  title     = {Picosecond dynamics in haemoglobin from different species: A quasielastic neutron scattering study},
  series = {Biochimica et biophysica acta (BBA): General Subjects},
  volume    = {1840},
  journal   = {Biochimica et biophysica acta (BBA): General Subjects},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-8006 (E-Journal); 0304-4165 (Print)},
  doi       = {10.1016/j.bbagen.2014.06.007},
  pages     = {2989 -- 2999},
  year      = {2014},
  language  = {en}
}
@article{MalechaKlubertHeinenFuchs2014,
  author    = {Malecha, Hartmut and Klubert, J. and Heinen-Fuchs, Sabine},
  title     = {Laserscanning passe? 3-D-Oberfl{\"a}chenmodelle aus Bilddaten und deren messtechnischer Nutzen},
  series = {Wasserwirtschaft},
  volume    = {Jg. 104},
  journal   = {Wasserwirtschaft},
  number    = {Nr. 9},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0043-0978},
  pages     = {32 -- 35},
  year      = {2014},
  language  = {de}
}
@article{RatkeMilowLisinskietal.2014,
  author    = {Ratke, Lorenz and Milow, Barbara and Lisinski, Susanne and Hoepfner, Sandra},
  title     = {On an effect of fine ceramic particles on the structure of aerogels},
  series = {Microgravity science and technology},
  volume    = {26},
  journal   = {Microgravity science and technology},
  publisher = {Springer Nature},
  address   = {Heidelberg},
  issn      = {0938-0108 ; 1875-0494},
  doi       = {10.1007/s12217-014-9380-2},
  pages     = {103 -- 110},
  year      = {2014},
  language  = {en}
}
@article{Balzer2014,
  author    = {Balzer, Hermann},
  title     = {Ausgestaltung und Steuerung des Netzes von Bankbeziehungen - Update nach 25 Jahren mithilfe einer explorativen Unternehmensbefragung / Arbeitskreis Finanzierung der Schmalenbach-Gesellschaft e.V. unter Mitarb. von Prof. Dr. Hermann Balzer...},
  series = {Zfbf : Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung},
  journal   = {Zfbf : Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung},
  number    = {H. 8},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  issn      = {0341-2687},
  pages     = {694 -- 723},
  year      = {2014},
  language  = {de}
}
@article{GuoSekiMiyamotoetal.2014,
  author    = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor with a novel photoexcitation method for a higher spatial resolution},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.369},
  pages     = {456 -- 459},
  year      = {2014},
  abstract  = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) realized a higher spatial resolution of chemical imaging. In this method, a modulated light probe, which generates the alternating photocurrent signal, is surrounded by a ring of constant light, which suppresses the lateral diffusion of photocarriers by enhancing recombination. A device simulation verified that a higher spatial resolution could be obtained by adjusting the gap between the modulated and constant light. It was also found that a higher intensity and a longer wavelength of constant light was more effective. However, there exists a tradeoff between the spatial resolution and the amplitude of the photocurrent, and thus, the signal-to-noise ratio. A tilted incidence of constant light was applied, which could achieve even higher resolution with a smaller loss of photocurrent.},
  language  = {en}
}
@article{MiyamotoSekiWagneretal.2014,
  author    = {Miyamoto, K. and Seki, K. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Enhancement of the spatial resolution of the chemical imaging sensor by a hybrid fiber-optic illumination},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.563},
  pages     = {612 -- 615},
  year      = {2014},
  abstract  = {The chemical imaging sensor, which is based on the principle of the light-addressable potentiometric sensor (LAPS), is a powerful tool to visualize the spatial distribution of chemical species on the sensor surface. The spatial resolution of this sensor depends on the diffusion of photocarriers excited by a modulated light. In this study, a novel hybrid fiber-optic illumination was developed to enhance the spatial resolution. It consists of a modulated light probe to generate a photocurrent signal and a ring of constant light, which suppresses the lateral diffusion of minority carriers excited by the modulated light. It is demonstrated that the spatial resolution was improved from 92 μm to 68 μm.},
  language  = {en}
}
@article{AlmajhdiSengerAmeretal.2014,
  author    = {Almajhdi, Fahad N. and Senger, Tilo and Amer, Haitham M. and Gissmann, Lutz and {\"O}hlschl{\"a}ger, Peter},
  title     = {Design of a highly effective therapeutic HPV16 E6/E7-specific DNA vaccine: optimization by different ways of sequence rearrangements (Shuffling)},
  series = {PLOS one},
  volume    = {11},
  journal   = {PLOS one},
  number    = {9},
  publisher = {PLOS},
  address   = {San Francisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0113461},
  pages     = {e113461},
  year      = {2014},
  abstract  = {Persistent infection with the high-risk Human Papillomavirus type 16 (HPV 16) is the causative event for the development of cervical cancer and other malignant tumors of the anogenital tract and of the head and neck. Despite many attempts to develop therapeutic vaccines no candidate has entered late clinical trials. An interesting approach is a DNA based vaccine encompassing the nucleotide sequence of the E6 and E7 viral oncoproteins. Because both proteins are consistently expressed in HPV infected cells they represent excellent targets for immune therapy. Here we report the development of 8 DNA vaccine candidates consisting of differently rearranged HPV-16 E6 and E7 sequences within one molecule providing all naturally occurring epitopes but supposedly lacking transforming activity. The HPV sequences were fused to the J-domain and the SV40 enhancer in order to increase immune responses. We demonstrate that one out of the 8 vaccine candidates induces very strong cellular E6- and E7- specific cellular immune responses in mice and, as shown in regression experiments, efficiently controls growth of HPV 16 positive syngeneic tumors. This data demonstrates the potential of this vaccine candidate to control persistent HPV 16 infection that may lead to malignant disease. It also suggests that different sequence rearrangements influence the immunogenecity by an as yet unknown mechanism.},
  language  = {en}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Funkstandards f{\"u}r Sensornetzwerke},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  volume    = {Bd. 63},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  number    = {H. 12},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {36 -- 41},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Echtzeit-Ethernet : Protokoll-Reigen},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  volume    = {Bd. 63},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  number    = {H. 26},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {24 -- 31},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Der Embedded Wireless-Report},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Wireless : Fachmedium f{\"u}r Entwicklungen funkbasierter Systeme},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Wireless : Fachmedium f{\"u}r Entwicklungen funkbasierter Systeme},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {18 -- 25},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Echtzeit-Ethernet mit Standardtechnik},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Embedded : Fachmagazin f{\"u}r die Entwicklung von Embedded-Systemen},
  volume    = {Bd. 63},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Embedded : Fachmagazin f{\"u}r die Entwicklung von Embedded-Systemen},
  number    = {H. 12},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {28 -- 32},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Feldbustechnologie},
  series = {Factory : der Durchblick in der Technik},
  journal   = {Factory : der Durchblick in der Technik},
  publisher = {WEKA-Industriemedien},
  address   = {Wien},
  pages     = {Publ. online},
  year      = {2014},
  language  = {de}
}
@article{DemnyHebel2014,
  author    = {Demny, Andreas and Hebel, Christoph},
  title     = {Rechnergest{\"u}tzte Ermittlung der Verbindungsfunktionsstufen und der verbindungsbezogenen Angebotsqualit{\"a}t nach den Richtlinien f{\"u}r integrierte Netzgestaltung nach RIN 2008},
  series = {Straßenverkehrstechnik : Organ der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen, der Bundesvereinigung der Straßenbau- und Verkehrsingenieure und der {\"O}sterreichischen Forschungsgesellschaft Straße und Verkehr ; Zeitschrift f{\"u}r Verkehrsplanung, Verkehrsmanagement, Verkehrssicherheit, Verkehrstechnik},
  volume    = {Jg. 58},
  journal   = {Straßenverkehrstechnik : Organ der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen, der Bundesvereinigung der Straßenbau- und Verkehrsingenieure und der {\"O}sterreichischen Forschungsgesellschaft Straße und Verkehr ; Zeitschrift f{\"u}r Verkehrsplanung, Verkehrsmanagement, Verkehrssicherheit, Verkehrstechnik},
  number    = {H. 12},
  publisher = {Kirschbaum Verlag},
  address   = {Bonn},
  issn      = {0039-2219},
  pages     = {811 -- 820},
  year      = {2014},
  language  = {de}
}
@article{Thomas2014,
  author    = {Thomas, Axel},
  title     = {Generation Y},
  series = {P.T. : Magazin f{\"u}r Wirtschaft und Gesellschaft},
  volume    = {10},
  journal   = {P.T. : Magazin f{\"u}r Wirtschaft und Gesellschaft},
  number    = {3},
  publisher = {OPS Netzwerk},
  address   = {Leipzig},
  issn      = {1860-501X},
  pages     = {6 -- 9},
  year      = {2014},
  language  = {de}
}
@article{ThomasWassenberg2014,
  author    = {Thomas, Axel and Wassenberg, Gerd},
  title     = {Erfolgreich sein im Kampf um die besten Talente : Employer Branding},
  series = {Wirtschaftliche Nachrichten der Industrie- und Handelskammer Aachen},
  journal   = {Wirtschaftliche Nachrichten der Industrie- und Handelskammer Aachen},
  publisher = {IHK Aachen},
  address   = {Aachen},
  year      = {2014},
  language  = {de}
}
@article{MartinGonzalezKotliarRiosMartinezetal.2014,
  author    = {Martin-Gonzalez, Anabel and Kotliar, Konstantin and Rios-Martinez, Jorge and Lanzl, Ines and Navab, Nassir},
  title     = {Mediated-reality magnification for macular degeneration rehabilitation},
  series = {Journal of Modern Optics},
  volume    = {61},
  journal   = {Journal of Modern Optics},
  number    = {17},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1362-3044},
  doi       = {10.1080/09500340.2014.936110},
  pages     = {1400 -- 1408},
  year      = {2014},
  language  = {en}
}
@article{ButenwegMeyerFehling2014,
  author    = {Butenweg, Christoph and Meyer, Udo and Fehling, Ekkehard},
  title     = {EU-Projekt INSYSME: Innovative Techniken f{\"u}r erdbebensichere Ausfachungsw{\"a}nde aus Ziegelmauerwerk in Stahlbetonrahmentragwerken},
  series = {Mauerwerk : European journal of masonry},
  volume    = {18},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {2},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201400612},
  pages     = {78 -- 81},
  year      = {2014},
  abstract  = {Am 1. Oktober 2013 ist das auf drei Jahre angelegte EU-Forschungsprojekt INSYSME - Innovative Systeme f{\"u}r erdbebentaugliche Ausfachungsw{\"a}nde aus Ziegelmauerwerk in Stahlbetonrahmentragwerken - gestartet. Unter der Koordination der Universit{\"a}t Padua beteiligen sich 16 Partner aus sechs europ{\"a}ischen L{\"a}ndern (Deutschland, Griechenland, Italien, Portugal, Rum{\"a}nien, T{\"u}rkei). Als deutsche Partner nehmen die Arbeitsgemeinschaft Mauerziegel aus Bonn, die Universit{\"a}t Kassel sowie das Ingenieurb{\"u}ro SDA-engineering GmbH aus Herzogenrath, teil. Ziel der deutschen Partner ist die Entwicklung von innovativen Ausfachungssystemen aus monolithischem w{\"a}rmed{\"a}mmenden Ziegelmauerwerk, mit denen nicht nur eine erh{\"o}hte Erdbebensicherheit, sondern auch die sichere Erf{\"u}llung der steigenden Anforderungen aus Windbeanspruchungen gew{\"a}hrleistet werden k{\"o}nnen. Die Forschungsergebnisse sollen vom Partner SDA-engineering GmbH in die bereits seit einigen Jahren verf{\"u}gbare Softwarel{\"o}sung MINEA [1] integriert werden. Weitere Informationen stehen auf den Websites des Projektes [2] zur Verf{\"u}gung. Im vorliegenden Beitrag werden nach einer kurzen thematischen Einf{\"u}hrung die Ergebnisse von Tastversuchen an senkrecht zur Ebene belasteten Ausfachungsw{\"a}nden aus Planziegelmauerwerk vorgestellt. Im Anschluss wird das geplante Arbeitsprogramm der deutschen Partner im Projekt INSYSME beschrieben.},
  language  = {de}
}
@article{GellertButenweg2014,
  author    = {Gellert, Christoph and Butenweg, Christoph},
  title     = {Seismic analysis of masonry structures in German earthquake zones according to DIN EN 1998-1},
  series = {Mauerwerk : European journal of masonry},
  volume    = {18},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {3-4},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201400626},
  pages     = {188 -- 196},
  year      = {2014},
  abstract  = {Die Erdbeben in Albstadt 1978 (Magnitude 5,7), Roermond 1992 (Magnitude 5,9) oder in Waldkirch 2004 (Magnitude 5,1) haben verdeutlicht, dass die erdbebensichere Auslegung von Mauerwerksbauten auch in Deutschland von großer Bedeutung ist. Bereits im Jahr 1981 wurde die DIN 4149 (1981) "Bauten in deutschen Erdbebengebieten - Lastannahmen, Bemessung und Ausf{\"u}hrung {\"u}blicher Hochbauten" eingef{\"u}hrt, in der aber f{\"u}r Mauerwerksbauten nur wenige Anforderungen gestellt wurden. Diese Norm wurde durch den NABau-Arbeitsausschuss "Erdbeben; Sonderfragen" des Deutschen Instituts f{\"u}r Normung e.V. (DIN) auf Grundlage des Eurocode 8 (2004) vollst{\"a}ndig {\"u}berarbeitet und durch die DIN 4149 (2005) abgel{\"o}st, die umfangreiche Regelungen f{\"u}r die seismische Auslegung von Mauerwerksbauten enth{\"a}lt. Mittlerweile liegen die DIN EN 1998-1 (2010) und der Nationale Anhang DIN EN 1998-1/NA (2011) vor, die nach Einarbeitung der Ergebnisse der durchgef{\"u}hrten Anwendungserprobung bauaufsichtlich eingef{\"u}hrt und die DIN 4149 (2005) ersetzen werden. Der folgende Beitrag gibt einen {\"U}berblick {\"u}ber die seismische Berechnung und Bemessung von Mauerwerksbauten nach dem europ{\"a}ischen Regelwerk und illustriert deren Anwendung an einem baupraktischen Beispiel.},
  language  = {de}
}