@article{BaroudWuBohneretal.2003,
  author    = {Baroud, G. and Wu, J.Z. and Bohner, M and Sponagel, Stefan and Steffen, T.},
  title     = {How to determine the permeability for cement infiltration into osteoporotic cancellous bone},
  series = {Medical Engineering \& Physics. 25 (2003), H. 4},
  journal   = {Medical Engineering \& Physics. 25 (2003), H. 4},
  issn      = {1350-4533},
  pages     = {283 -- 288},
  year      = {2003},
  abstract  = {Cement augmentation is an emerging surgical procedure in which bone cement is used to infiltrate and reinforce osteoporotic vertebrae. Although this infiltration procedure has been widely applied, it is performed empirically and little is known about the flow characteristics of cement during the injection process. We present a theoretical and experimental approach to investigate the intertrabecular bone permeability during the infiltration procedure. The cement permeability was considered to be dependent on time, bone porosity, and cement viscosity in our analysis. In order to determine the time-dependent permeability, ten cancellous bone cores were harvested from osteoporotic vertebrae, infiltrated with acrylic cement at a constant flow rate, and the pressure drop across the cores during the infiltration was measured. The viscosity dependence of the permeability was determined based on published experimental data. The theoretical model for the permeability as a function of bone porosity and time was then fit to the testing data. Our findings suggest that the intertrabecular bone permeability depends strongly on time. For instance, the initial permeability (60.89 mm4/N.s) reduced to approximately 63\% of its original value within 18 seconds. This study is the first to analyze cement flow through osteoporotic bone. The theoretical and experimental models provided in this paper are generic. Thus, they can be used to systematically study and optimize the infiltration process for clinical practice.},
  subject      = {Osteoporose},
  language  = {en}
}
@inproceedings{StaatHeitzer2002,
  author    = {Staat, Manfred and Heitzer, Michael},
  title     = {The restricted influence of kinematic hardening on shakedown loads},
  year      = {2002},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratcheting. To this end it is important to make a clear distinction between the shakedown range and the ratcheting range. In cyclic plasticity more sophisticated hardening models have been suggested in order to model the strain evolution observed in ratcheting experiments. The hardening models used in shakedown analysis are comparatively simple. It is shown that shakedown analysis can make quite stable predictions of admissible load ranges despite the simplicity of the underlying hardening models. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis. Both give identical or similar shakedown ranges. Structural shakedown analyses show that the loading may have a more pronounced effect than the hardening model.},
  subject      = {Biomedizinische Technik},
  language  = {en}
}
@article{Staat2004,
  author    = {Staat, Manfred},
  title     = {Plastic collapse analysis of longitudinally flawed pipes and vessels},
  year      = {2004},
  abstract  = {Improved collapse loads of thick-walled, crack containing pipes and vessels are suggested. Very deep cracks have a residual strength which is better modelled by a global limit load. In all burst tests, the ductility of pressure vessel steels was sufficiently high whereby the burst pressure could be predicted by limit analysis with no need to apply fracture mechanics. The relative prognosis error increases however, for long and deep defects due to uncertainties of geometry and strength data.},
  subject      = {Druckbeh{\"a}lter},
  language  = {en}
}
@article{Staat2005,
  author    = {Staat, Manfred},
  title     = {Local and global collapse pressure of longitudinally flawed pipes and cylindrical vessels},
  year      = {2005},
  abstract  = {Limit loads can be calculated with the finite element method (FEM) for any component, defect geometry, and loading. FEM suggests that published long crack limit formulae for axial defects under-estimate the burst pressure for internal surface defects in thick pipes while limit loads are not conservative for deep cracks and for pressure loaded crack-faces. Very deep cracks have a residual strength, which is modelled by a global collapse load. These observations are combined to derive new analytical local and global collapse loads. The global collapse loads are close to FEM limit analyses for all crack dimensions.},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}
@article{Staat2005,
  author    = {Staat, Manfred},
  title     = {Direct finite element route for design-by-analysis of pressure components},
  year      = {2005},
  abstract  = {In the new European standard for unfired pressure vessels, EN 13445-3, there are two approaches for carrying out a Design-by-Analysis that cover both the stress categorization method (Annex C) and the direct route method (Annex B) for a check against global plastic deformation and against progressive plastic deformation. This paper presents the direct route in the language of limit and shakedown analysis. This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for mechanical and thermal actions. One observation from the examples is that the so-called 3f (3Sm) criterion fails to be a reliable check against progressive plastic deformation. Precise conditions are given, which greatly restrict the applicability of the 3f criterion.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@article{Staat2003,
  author    = {Staat, Manfred},
  title     = {Shakedown and ratchetting under tension-torsion loadings: analysis and experiments},
  year      = {2003},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratchetting. To this end it is important to make a clear distinction between the shakedown range and the ratchetting range. The performed experiment comprised a hollow tension specimen which was subjected to alternating axial forces, superimposed with constant moments. First, a series of uniaxial tests has been carried out in order to calibrate a bounded kinematic hardening rule. The load parameters have been selected on the basis of previous shakedown analyses with the PERMAS code using a kinematic hardening material model. It is shown that this shakedown analysis gives reasonable agreement between the experimental and the numerical results. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@inproceedings{Staat2003,
  author    = {Staat, Manfred},
  title     = {Design by Analysis of Pressure Components by non-linear Optimization},
  year      = {2003},
  abstract  = {This paper presents the direct route to Design by Analysis (DBA) of the new European pressure vessel standard in the language of limit and shakedown analysis (LISA). This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for some examples from the DBA-Manual. One observation from the examples is, that the optimisation approach gives reliable and close lower bound solutions leading to simple and optimised design decision.},
  language  = {en}
}
@article{VuStaat2004,
  author    = {Vu, Duc-Khoi and Staat, Manfred},
  title     = {An algorithm for shakedown analysis of structure with temperature dependent yield stress},
  year      = {2004},
  abstract  = {This work is an attempt to answer the question: How to use convex programming in shakedown analysis of structures made of materials with temperature-dependent properties. Based on recently established shakedown theorems and formulations, a dual relationship between upper and lower bounds of the shakedown limit load is found, an algorithmfor shakedown analysis is proposed. While the original problem is neither convex nor concave, the algorithm presented here has the advantage of employing convex programming tools.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@article{KuehnHaugnerStaatetal.2004,
  author    = {K{\"u}hn, Raoul-Roman and Haugner, Werner and Staat, Manfred and Sponagel, Stefan},
  title     = {A Two Phase Mixture Model based on Bone Observation},
  year      = {2004},
  abstract  = {An optimization method is developed to describe the mechanical behaviour of the human cancellous bone. The method is based on a mixture theory. A careful observation of the behaviour of the bone material leads to the hypothesis that the bone density is controlled by the principal stress trajectories (Wolff's law). The basic idea of the developed method is the coupling of a scalar value via an eigenvalue problem to the principal stress trajectories. On the one hand this theory will permit a prediction of the reaction of the biological bone structure after the implantation of a prosthesis, on the other hand it may be useful in engineering optimization problems. An analytical example shows its efficiency.},
  subject      = {Knochen},
  language  = {en}
}
@misc{Staat2006,
  author    = {Staat, Manfred},
  title     = {Engineering Mechanics. Lecture Notes. 2nd edition, translation of the 3rd corrected and extended German edition of "Technische Mechanik"},
  year      = {2006},
  abstract  = {English translation of the corrected lectures notes of Sebastian Kr{\"a}mer. Contents 0 Introduction to Mechanics 1 Statics of Rigid Bodies 2 Elastostatics (Strength of Materials) 3 Kinematics 4 Kinetics Literature},
  subject      = {Technische Mechanik},
  language  = {en}
}
@misc{StaatBarry2006,
  author    = {Staat, Manfred and Barry, Steve},
  title     = {Continuum Mechanics with an Introduction to the Finite Element Method / Steve Barry; Manfred Staat. With extensions by Manfred Staat.},
  year      = {2006},
  abstract  = {Contents: 1 Introduction 2 One Dimensional Continuum Mechanics 3 Tensors 4 Three Dimensional Stress and Strain 5 Conservation Laws 6 Contiunuum Modelling 7 Plain Problems 8 Questions 9 Reference Information},
  subject      = {Technische Mechanik},
  language  = {en}
}
@inproceedings{TranStaatKreissig2007,
  author    = {Tran, Thanh Ngoc and Staat, Manfred and Kreißig, R.},
  title     = {Calculation of load carrying capacity of shell structures with elasto-plastic material by direct methods},
  year      = {2007},
  abstract  = {Proceedings of the International Conference on Material Theory and Nonlinear Dynamics. MatDyn. Hanoi, Vietnam, Sept. 24-26, 2007, 8 p. In this paper, a method is introduced to determine the limit load of general shells using the finite element method. The method is based on an upper bound limit and shakedown analysis with elastic-perfectly plastic material model. A non-linear constrained optimisation problem is solved by using Newton's method in conjunction with a penalty method and the Lagrangean dual method. Numerical investigation of a pipe bend subjected to bending moments proves the effectiveness of the algorithm.},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}
@inproceedings{TranStaatKreissig2007,
  author    = {Tran, Thanh Ngoc and Staat, Manfred and Kreißig, R.},
  title     = {Finite element shakedown and limit reliability analysis of thin shells},
  year      = {2007},
  abstract  = {A procedure for the evaluation of the failure probability of elastic-plastic thin shell structures is presented. The procedure involves a deterministic limit and shakedown analysis for each probabilistic iteration which is based on the kinematical approach and the use the exact Ilyushin yield surface. Based on a direct definition of the limit state function, the non-linear problems may be efficiently solved by using the First and Second Order Reliabiblity Methods (Form/SORM). This direct approach reduces considerably the necessary knowledge of uncertain technological input data, computing costs and the numerical error. In: Computational plasticity / ed. by Eugenio Onate. Dordrecht: Springer 2007. VII, 265 S. (Computational Methods in Applied Sciences ; 7) (COMPLAS IX. Part 1 . International Center for Numerical Methods in Engineering (CIMNE)). ISBN 978-1-402-06576-7 S. 186-189},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}
@inproceedings{Staat2006,
  author    = {Staat, Manfred},
  title     = {Problems and chances for probabilistic fracture mechanics in the analysis of steel pressure boundary reliability. - {\"U}berarb. Ausg.},
  year      = {2006},
  abstract  = {In: Technical feasibility and reliability of passive safety systems for nuclear power plants. Proceedings of an Advisory Group Meeting held in J{\"u}lich, 21-24 November 1994. - Vienna , 1996. - Seite: 43 - 55 IAEA-TECDOC-920 Abstract: It is shown that the difficulty for probabilistic fracture mechanics (PFM) is the general problem of the high reliability of a small population. There is no way around the problem as yet. Therefore what PFM can contribute to the reliability of steel pressure boundaries is demon­strated with the example of a typical reactor pressure vessel and critically discussed. Although no method is distinguishable that could give exact failure probabilities, PFM has several addi­tional chances. Upper limits for failure probability may be obtained together with trends for design and operating conditions. Further, PFM can identify the most sensitive parameters, improved control of which would increase reliability. Thus PFM should play a vital role in the analysis of steel pressure boundaries despite all shortcomings.},
  subject      = {Bruchmechanik},
  language  = {en}
}
@article{SeifarthGossmannGrosseetal.2015,
  author    = {Seifarth, Volker and Goßmann, Matthias and Grosse, J. O. and Becker, C. and Heschel, I. and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Development of a Bioreactor to Culture Tissue Engineered Ureters Based on the Application of Tubular OPTIMAIX 3D Scaffolds},
  series = {Urologia Internationalis},
  volume    = {2015},
  journal   = {Urologia Internationalis},
  number    = {95},
  publisher = {Karger},
  address   = {Basel},
  issn      = {0042-1138},
  doi       = {10.1159/000368419},
  pages     = {106 -- 113},
  year      = {2015},
  language  = {en}
}
@article{MartinGonzalezKotliarRiosMartinezetal.2014,
  author    = {Martin-Gonzalez, Anabel and Kotliar, Konstantin and Rios-Martinez, Jorge and Lanzl, Ines and Navab, Nassir},
  title     = {Mediated-reality magnification for macular degeneration rehabilitation},
  series = {Journal of Modern Optics},
  volume    = {61},
  journal   = {Journal of Modern Optics},
  number    = {17},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1362-3044},
  doi       = {10.1080/09500340.2014.936110},
  pages     = {1400 -- 1408},
  year      = {2014},
  language  = {en}
}
@article{KotliarKharoubiSchmidtTrucksaessetal.2009,
  author    = {Kotliar, Konstantin and Kharoubi, A. and Schmidt-Trucks{\"a}ß, A. and Halle, M. and Lanzl, I.},
  title     = {Does internal longitudinal microstructure of retinal veins change with age in medically healthy persons?},
  series = {Acta Ophthalmologica},
  volume    = {Vol. 87},
  journal   = {Acta Ophthalmologica},
  number    = {Suppl. S244},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1600-0420 (E-Journal); 1755-3768 (E-Journal); 0001-639X (Print); 1395-3907 (Print); 1755-375X (Print)},
  pages     = {0},
  year      = {2009},
  language  = {en}
}
@article{FrotscherKochStaat2015,
  author    = {Frotscher, Ralf and Koch, Jan-Peter and Staat, Manfred},
  title     = {Computational investigation of drug action on human-induced stem cell derived cardiomyocytes},
  series = {Journal of biomechanical engineering},
  volume    = {Vol. 137},
  journal   = {Journal of biomechanical engineering},
  number    = {iss. 7},
  publisher = {ASME},
  address   = {New York},
  issn      = {1528-8951 (E-Journal); 0148-0731 (Print)},
  doi       = {10.1115/1.4030173},
  pages     = {071002-1 -- 071002-7},
  year      = {2015},
  language  = {en}
}
@article{DuongNguyenTranetal.2015,
  author    = {Duong, Minh Tuan and Nguyen, Nhu Huynh and Tran, Thanh Ngoc and Tolba, R. H. and Staat, Manfred},
  title     = {Influence of refrigerated storage on tensile mechanical properties of porcine liver and spleen},
  series = {International biomechanics},
  volume    = {Vol. 2},
  journal   = {International biomechanics},
  number    = {Iss. 1},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {2333-5432},
  doi       = {10.1080/23335432.2015.1049295},
  pages     = {79 -- 88},
  year      = {2015},
  language  = {en}
}
@inproceedings{FrotscherStaat2015,
  author    = {Frotscher, Ralf and Staat, Manfred},
  title     = {An electromechanical model for cardiac tissue constructs},
  series = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  booktitle = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  publisher = {RWTH Aachen University},
  address   = {Aachen},
  organization    = {ECCOMAS Young Investigators Conference <3, 2015, Aachen>},
  pages     = {1 -- 4},
  year      = {2015},
  language  = {en}
}
@inproceedings{BhattaraiFrotscherStaat2015,
  author    = {Bhattarai, Aroj and Frotscher, Ralf and Staat, Manfred},
  title     = {Biomechanical study of the female pelvic floor dysfunction using the finite element method},
  series = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen , Germany, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  booktitle = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen , Germany, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  publisher = {RWTH Aachen University},
  address   = {Aachen},
  organization    = {ECCOMAS Young Investigators Conference <3, 2015, Aachen>},
  pages     = {1 -- 4},
  year      = {2015},
  language  = {en}
}
@inproceedings{DuongNguyenStaat2015,
  author    = {Duong, Minh Tuan and Nguyen, N. H. and Staat, Manfred},
  title     = {Modeling and simulation of a growing mass by the Smoothed Finite Element Method (SFEM)},
  series = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, Germany, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  booktitle = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen, Germany, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  publisher = {RWTH Aachen University},
  address   = {Aachen},
  organization    = {ECCOMAS Young Investigators Conference <3, 2015, Aachen>},
  pages     = {1 -- 4},
  year      = {2015},
  language  = {en}
}
@inproceedings{PhamStaat2015,
  author    = {Pham, Phu Tinh and Staat, Manfred},
  title     = {A simplification for shakedown analysis of hardening structures},
  series = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen , Germany, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  booktitle = {Conference proceedings of the YIC GACM 2015 : 3rd ECCOMAS Young Investigators Conference and 6th GACM Colloquium on Computational Mechanics , Aachen , Germany, 20.07.2015 - 23.07.2015 / ed.: Stefanie Elgeti ; Jaan-Willem Simon},
  publisher = {RWTH Aachen University},
  address   = {Aachen},
  organization    = {ECCOMAS Young Investigators Conference <3, 2015, Aachen>},
  pages     = {1 -- 4},
  year      = {2015},
  language  = {en}
}
@inproceedings{FrotscherStaat2015,
  author    = {Frotscher, Ralf and Staat, Manfred},
  title     = {Homogenization of a cardiac tissue construct},
  series = {CMBE15 : 4th International Conference on Computational \& Mathematical Biomedical Engineering ; 29th June - 1st July 2015 ; {\´E}cole Normale Sup{\´e}rieure de Cachan ; Cachan (Paris), France},
  booktitle = {CMBE15 : 4th International Conference on Computational \& Mathematical Biomedical Engineering ; 29th June - 1st July 2015 ; {\´E}cole Normale Sup{\´e}rieure de Cachan ; Cachan (Paris), France},
  editor    = {Nithiarasu, Perumal},
  publisher = {CMBE},
  address   = {[s.l.]},
  issn      = {2227-9385},
  pages     = {645 -- 648},
  year      = {2015},
  language  = {en}
}
@inproceedings{FrotscherDuongStaat2015,
  author    = {Frotscher, Ralf and Duong, Minh Tuan and Staat, Manfred},
  title     = {Simulating beating cardiomyocytes with electromechanical coupling},
  series = {II. International Conference on Biomedical Technology : 28-30 October 2015 Hannover, Germany / T. Lenarz, P. Wriggers (Eds.)},
  booktitle = {II. International Conference on Biomedical Technology : 28-30 October 2015 Hannover, Germany / T. Lenarz, P. Wriggers (Eds.)},
  organization    = {International Conference on Biomedical Technology <2, 2015, Hannover>},
  pages     = {1 -- 2},
  year      = {2015},
  language  = {en}
}
@article{DuongNguyenStaat2015,
  author    = {Duong, Minh Tuan and Nguyen, Nhu Huynh and Staat, Manfred},
  title     = {Physical response of hyperelastic models for composite materials and soft tissues},
  series = {Asia pacific journal on computational engineering},
  volume    = {2},
  journal   = {Asia pacific journal on computational engineering},
  number    = {3 (December 2015)},
  issn      = {2196-1166},
  doi       = {10.1186/s40540-015-0015-x},
  pages     = {1 -- 18},
  year      = {2015},
  language  = {en}
}
@article{CehreliAkpinarTemizArtmannetal.2015,
  author    = {Cehreli, Ruksan and Akpinar, Hale and Temiz Artmann, Ayseg{\"u}l and Sagol, Ozgul},
  title     = {Effects of Glutamine and Omega-3 Fatty Acids on Erythrocyte Deformability and Oxidative Damage in Rat Model of Enterocolitis},
  series = {Gastroenterology Research},
  volume    = {8},
  journal   = {Gastroenterology Research},
  number    = {5},
  issn      = {1918-2813},
  doi       = {10.14740/gr683w},
  pages     = {265 -- 273},
  year      = {2015},
  language  = {en}
}
@article{KowalskiLinderZierkeetal.2016,
  author    = {Kowalski, Julia and Linder, Peter and Zierke, S. and Wulfen, B. van and Clemens, J. and Konstantinidis, K. and Ameres, G. and Hoffmann, R. and Mikucki, J. and Tulaczyk, S. and Funke, O. and Blandfort, D. and Espe, Clemens and Feldmann, Marco and Francke, Gero and Hiecker, S. and Plescher, Engelbert and Sch{\"o}ngarth, Sarah and Dachwald, Bernd and Digel, Ilya and Artmann, Gerhard and Eliseev, D. and Heinen, D. and Scholz, F. and Wiebusch, C. and Macht, S. and Bestmann, U. and Reineking, T. and Zetzsche, C. and Schill, K. and F{\"o}rstner, R. and Niedermeier, H. and Szumski, A. and Eissfeller, B. and Naumann, U. and Helbing, K.},
  title     = {Navigation technology for exploration of glacier ice with maneuverable melting probes},
  series = {Cold Regions Science and Technology},
  journal   = {Cold Regions Science and Technology},
  number    = {123},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0165-232X},
  doi       = {10.1016/j.coldregions.2015.11.006},
  pages     = {53 -- 70},
  year      = {2016},
  abstract  = {The Saturnian moon Enceladus with its extensive water bodies underneath a thick ice sheet cover is a potential candidate for extraterrestrial life. Direct exploration of such extraterrestrial aquatic ecosystems requires advanced access and sampling technologies with a high level of autonomy. A new technological approach has been developed as part of the collaborative research project Enceladus Explorer (EnEx). The concept is based upon a minimally invasive melting probe called the IceMole. The force-regulated, heater-controlled IceMole is able to travel along a curved trajectory as well as upwards. Hence, it allows maneuvers which may be necessary for obstacle avoidance or target selection. Maneuverability, however, necessitates a sophisticated on-board navigation system capable of autonomous operations. The development of such a navigational system has been the focal part of the EnEx project. The original IceMole has been further developed to include relative positioning based on in-ice attitude determination, acoustic positioning, ultrasonic obstacle and target detection integrated through a high-level sensor fusion. This paper describes the EnEx technology and discusses implications for an actual extraterrestrial mission concept.},
  language  = {en}
}
@article{GrundmannDachwaldGrimmetal.2015,
  author    = {Grundmann, Jan Thimo and Dachwald, Bernd and Grimm, Christian D. and Kahle, Ralph and Koch, Aaron Dexter and Krause, Christian and Lange, Caroline and Quantius, Dominik and Ulamec, Stephan},
  title     = {Spacecraft for Hypervelocity Impact Research - An Overview of Capabilities, Constraints and the Challenges of Getting There},
  series = {Procedia Engineering},
  volume    = {Vol. 103},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2015.04.021},
  pages     = {151 -- 158},
  year      = {2015},
  language  = {en}
}
@inproceedings{GrundmannBauerBieleetal.2015,
  author    = {Grundmann, Jan Thimo and Bauer, Waldemar and Biele, Jens and Cordero, Frederico and Dachwald, Bernd and Koncz, Alexander and Krause, Christian and Mikschl, Tobias and Montenegro, Sergio and Quantius, Dominik and Ruffer, Michael and Sasaki, Kaname and Schmitz, Nicole and Seefeldt, Patric and T{\´o}th, Norbert and Wejmo, Elisabet},
  title     = {From Sail to Soil - Getting Sailcraft Out of the Harbour on a Visit to One of Earth's Nearest Neighbours},
  series = {4th IAA Planetary Denfense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  booktitle = {4th IAA Planetary Denfense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  pages     = {20 S.},
  year      = {2015},
  language  = {en}
}
@inproceedings{PirovanoSeefeldtDachwaldetal.2015,
  author    = {Pirovano, Laura and Seefeldt, Patric and Dachwald, Bernd and Noomen, Ron},
  title     = {Attitude and Orbital Dynamics Modeling for an Uncontrolled Solar-Sail Experiment in Low-Earth Orbit},
  series = {25th International Symposium on Spaceflight Dynamics, 2015, Munich, Germany},
  booktitle = {25th International Symposium on Spaceflight Dynamics, 2015, Munich, Germany},
  pages     = {15 S.},
  year      = {2015},
  language  = {en}
}
@incollection{DigelSadykovTemizArtmannetal.2015,
  author    = {Digel, Ilya and Sadykov, R. and Temiz Artmann, Ayseg{\"u}l and Artmann, Gerhard},
  title     = {Changes in intestinal microflora in rats induced by oral exposure to low lead (II) concentrations},
  series = {Lead Exposure and Poisoning: Clinical Symptoms, Medical Management and Preventive Strategies},
  booktitle = {Lead Exposure and Poisoning: Clinical Symptoms, Medical Management and Preventive Strategies},
  publisher = {Nova Science Publ.},
  isbn      = {9781634826990},
  pages     = {75 -- 99},
  year      = {2015},
  language  = {en}
}
@article{GossmannFrotscherLinderetal.2016,
  author    = {Goßmann, Matthias and Frotscher, Ralf and Linder, Peter and Bayer, Robin and Epple, U. and Staat, Manfred and Temiz Artmann, Ayseg{\"u}l and Artmann, Gerhard},
  title     = {Mechano-pharmacological characterization of cardiomyocytes derived from human induced pluripotent stem cells},
  series = {Cellular physiology and biochemistry},
  volume    = {38},
  journal   = {Cellular physiology and biochemistry},
  number    = {3},
  publisher = {Karger},
  address   = {Basel},
  issn      = {1421-9778 (Online)},
  doi       = {10.1159/000443124},
  pages     = {1182 -- 1198},
  year      = {2016},
  abstract  = {Background/Aims: Common systems for the quantification of cellular contraction rely on animal-based models, complex experimental setups or indirect approaches. The herein presented CellDrum technology for testing mechanical tension of cellular monolayers and thin tissue constructs has the potential to scale-up mechanical testing towards medium-throughput analyses. Using hiPS-Cardiac Myocytes (hiPS-CMs) it represents a new perspective of drug testing and brings us closer to personalized drug medication. Methods: In the present study, monolayers of self-beating hiPS-CMs were grown on ultra-thin circular silicone membranes and deflect under the weight of the culture medium. Rhythmic contractions of the hiPS-CMs induced variations of the membrane deflection. The recorded contraction-relaxation-cycles were analyzed with respect to their amplitudes, durations, time integrals and frequencies. Besides unstimulated force and tensile stress, we investigated the effects of agonists and antagonists acting on Ca²⁺ channels (S-Bay K8644/verapamil) and Na⁺ channels (veratridine/lidocaine). Results: The measured data and simulations for pharmacologically unstimulated contraction resembled findings in native human heart tissue, while the pharmacological dose-response curves were highly accurate and consistent with reference data. Conclusion: We conclude that the combination of the CellDrum with hiPS-CMs offers a fast, facile and precise system for pharmacological, toxicological studies and offers new preclinical basic research potential.},
  language  = {en}
}
@article{FrotscherMuanghongDursunetal.2016,
  author    = {Frotscher, Ralf and Muanghong, Danita and Dursun, G{\"o}zde and Goßmann, Matthias and Temiz Artmann, Ayseg{\"u}l and Staat, Manfred},
  title     = {Sample-specific adaption of an improved electro-mechanical model of in vitro cardiac tissue},
  series = {Journal of Biomechanics},
  volume    = {49},
  journal   = {Journal of Biomechanics},
  number    = {12},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0021-9290 (Print)},
  doi       = {10.1016/j.jbiomech.2016.01.039},
  pages     = {2428 -- 2435},
  year      = {2016},
  abstract  = {We present an electromechanically coupled computational model for the investigation of a thin cardiac tissue construct consisting of human-induced pluripotent stem cell-derived atrial, ventricular and sinoatrial cardiomyocytes. The mechanical and electrophysiological parts of the finite element model, as well as their coupling are explained in detail. The model is implemented in the open source finite element code Code_Aster and is employed for the simulation of a thin circular membrane deflected by a monolayer of autonomously beating, circular, thin cardiac tissue. Two cardio-active drugs, S-Bay K8644 and veratridine, are applied in experiments and simulations and are investigated with respect to their chronotropic effects on the tissue. These results demonstrate the potential of coupled micro- and macroscopic electromechanical models of cardiac tissue to be adapted to experimental results at the cellular level. Further model improvements are discussed taking into account experimentally measurable quantities that can easily be extracted from the obtained experimental results. The goal is to estimate the potential to adapt the presented model to sample specific cell cultures.},
  language  = {en}
}
@inproceedings{JungStaatMueller2016,
  author    = {Jung, Alexander and Staat, Manfred and M{\"u}ller, Wolfram},
  title     = {Effect of wind on flight style optimisation in ski jumping},
  series = {15th International Symposium on Computer Simulation in Biomechanics ; July 9th-11th 2015, Edinburgh, UK},
  booktitle = {15th International Symposium on Computer Simulation in Biomechanics ; July 9th-11th 2015, Edinburgh, UK},
  publisher = {The University of Edinburgh ; Loughborough University},
  address   = {Edinburgh},
  pages     = {53 -- 54},
  year      = {2016},
  language  = {en}
}
@inproceedings{PeloniCeriottiDachwald2015,
  author    = {Peloni, A. and Ceriotti, M. and Dachwald, Bernd},
  title     = {Preliminary trajectory design of a multiple NEO rendezvous mission through solar sailing},
  series = {Proceedings of the International Astronautical Congress, IAC, Vol. 8, 2014},
  booktitle = {Proceedings of the International Astronautical Congress, IAC, Vol. 8, 2014},
  publisher = {Curran},
  address   = {Red Hook, NY},
  isbn      = {978-1-63439-986-9},
  pages     = {5352 -- 5366},
  year      = {2015},
  language  = {en}
}
@article{HacklMuellerStaatetal.2016,
  author    = {Hackl, Michael and M{\"u}ller, Lars-Peter and Staat, Manfred and Kahmann, Stephanie Lucina and Wegmann, Kilian},
  title     = {Proximal phalangeal neck fractures of the hand — a biomechanical comparison of three fixation techniques},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4080-7},
  pages     = {148 -- 149},
  year      = {2016},
  abstract  = {Plate osteosynthesis of displaced proximal phalangeal neck fractures of the hand allows early mobilization due to a stable internal fixation. Nevertheless, joint stiffness—because of soft tissue irritation—represents a common complication leading to high complication rates. Del Pinal et al. recently reported promising clinical results for a new, minimally invasive fixation technique with a cannulated headless intramedullary compression screw. Hence, the aim of this study was to compare plate fixation of proximal phalangeal neck fractures to less two less invasive techniques: Crossed k-wire fixation and intramedullary screw fixation. We hypothesized that these fixation techniques provide inferior stability when compared to plate osteosynthesis.},
  language  = {en}
}
@article{HacklKahmannWegmannetal.2016,
  author    = {Hackl, Michael and Kahmann, Stephanie Lucina and Wegmann, Kilian and Ries, Christian and Staat, Manfred and M{\"u}ller, Lars-Peter},
  title     = {Shortening osteotomy of the proximal radius — a treatment option for isolated osteoarthritis of the lateral column of the elbow joint?},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4080-7},
  pages     = {128 -- 129},
  year      = {2016},
  abstract  = {Treatment of posttraumatic osteoarthritis of the radial column of the elbow joint remains a challenging yet common issue. While partial joint replacement leads to high revision rates, radial head excision has shown to severely increase joint instability. Shortening osteotomy of the radius could be an option to decrease the contact pressure of the radiohumeral joint and thereby pain levels without causing valgus instability. Hence, the aim of this biomechanical study was to evaluate the effects of radial shortening on axial load distribution and valgus stability of the elbow joint.},
  language  = {en}
}
@article{HacklLeschingerStaatetal.2016,
  author    = {Hackl, Michael and Leschinger, T. and Staat, Manfred and M{\"u}ller, Lars-Peter and Wegmann, Kilian},
  title     = {Reconstruction of the interosseous membrane in the Essex Lopresti lesion — a biomechanical evaluation},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4080-7},
  pages     = {130 -- 131},
  year      = {2016},
  abstract  = {Surgical reconstruction of the interosseous membrane (IOM) could restore longitudinal forearm stability to avoid persisting disability due to capituloradial and ulnocarpal impingement in Essex Lopresti lesions. This biomechanical study aimed to assess longitudinal forearm stability of intact specimens, after sectioning of the IOM and after reconstruction with a TightRope construct using either a single or double bundle technique.},
  language  = {en}
}
@article{WegmannHacklStaatetal.2016,
  author    = {Wegmann, Kilian and Hackl, Michael and Staat, Manfred and Mayer, Katharina and M{\"u}ller, Lars-Peter},
  title     = {Double plate osteosynthesis of proximal ulna fractures: biomechanical and clinical results},
  series = {Knee surgery, sports traumatology, arthroscopy},
  volume    = {Volume 24},
  journal   = {Knee surgery, sports traumatology, arthroscopy},
  number    = {Supplement 1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0942-2056},
  doi       = {10.1007/s00167-016-4079-0},
  pages     = {58 -- 59},
  year      = {2016},
  abstract  = {While plate fixation of proximal ulna fractures might lead to superior clinical results compared to tension band wiring, regular plates represent an established risk factor for wound complications. The olecranon double plates (Medartis, Basel, CH) might decrease complications related to the osteosynthesis because of their low profile and better anatomical fit. This study aimed to evaluate the biomechanical performance and clinical results of the olecranon double plates.},
  language  = {en}
}
@article{PookhalilAmoabedinyTabeshetal.2016,
  author    = {Pookhalil, Ali and Amoabediny, Ghassem and Tabesh, Hadi and Behbahani, Mehdi and Mottaghy, Khosrow},
  title     = {A new approach for semiempirical modeling of mechanical blood trauma},
  series = {The international journal of artificial organs},
  volume    = {39},
  journal   = {The international journal of artificial organs},
  number    = {4},
  publisher = {Sage},
  address   = {London},
  issn      = {1724-6040},
  doi       = {10.5301/ijao.5000474},
  pages     = {171 -- 177},
  year      = {2016},
  abstract  = {Purpose Two semi-empirical models were recently published, both making use of existing literature data, but each taking into account different physical phenomena that trigger hemolysis. In the first model, hemoglobin (Hb) release is described as a permeation procedure across the membrane, assuming a shear stress-dependent process (sublethal model). The second model only accounts for hemoglobin release that is caused by cell membrane breakdown, which occurs when red blood cells (RBC) undergo mechanically induced shearing for a period longer than the threshold time (nonuniform threshold model). In this paper, we introduce a model that considers the hemolysis generated by both these possible phenomena. Methods Since hemolysis can possibly be caused by permeation of hemoglobin through the RBC functional membrane as well as by release of hemoglobin from RBC membrane breakdown, our proposed model combines both these models. An experimental setup consisting of a Couette device was utilized for validation of our proposed model. Results A comparison is presented between the damage index (DI) predicted by the proposed model vs. the sublethal model vs. the nonthreshold model and experimental datasets. This comparison covers a wide range of shear stress for both human and porcine blood. An appropriate agreement between the measured DI and the DI predicted by the present model was obtained. Conclusions The semiempirical hemolysis model introduced in this paper aims for significantly enhanced conformity with experimental data. Two phenomenological outcomes become possible with the proposed approach: an estimation of the average time after which cell membrane breakdown occurs under the applied conditions, and a prediction of the ratio between the phenomena involved in hemolysis.},
  language  = {en}
}
@inproceedings{BhattaraiStaat2016,
  author    = {Bhattarai, Aroj and Staat, Manfred},
  title     = {Female pelvic floor dysfunction: progress weakening of the support system},
  series = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  booktitle = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  editor    = {Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  doi       = {10.17185/duepublico/40821},
  pages     = {11 -- 12},
  year      = {2016},
  abstract  = {The structure of the female pelvic floor (PF) is an inter-related system of bony pelvis,muscles, pelvic organs, fascias, ligaments, and nerves with multiple functions. Mechanically, thepelvic organ support system are of two types: (I) supporting system of the levator ani (LA) muscle,and (II) the suspension system of the endopelvic fascia condensation [1], [2]. Significantdenervation injury to the pelvic musculature, depolimerization of the collagen fibrils of the softvaginal hammock, cervical ring and ligaments during pregnancy and vaginal delivery weakens thenormal functions of the pelvic floor. Pelvic organ prolapse, incontinence, sexual dysfunction aresome of the dysfunctions which increases progressively with age and menopause due toweakened support system according to the Integral theory [3]. An improved 3D finite elementmodel of the female pelvic floor as shown in Fig. 1 is constructed that: (I) considers the realisticsupport of the organs to the pelvic side walls, (II) employs the improvement of our previous FEmodel [4], [5] along with the patient based geometries, (III) incorporates the realistic anatomy andboundary conditions of the endopelvic (pubocervical and rectovaginal) fascia, and (IV) considersvarying stiffness of the endopelvic fascia in the craniocaudal direction [3]. Several computationsare carried out on the presented computational model with healthy and damaged supportingtissues, and comparisons are made to understand the physiopathology of the female PF disorders.},
  language  = {en}
}
@inproceedings{JungStaat2016,
  author    = {Jung, Alexander and Staat, Manfred},
  title     = {Computing olympic gold: Ski jumping as an example},
  series = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  booktitle = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  editor    = {Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-06-6},
  doi       = {10.17185/duepublico/40821},
  pages     = {54 -- 55},
  year      = {2016},
  language  = {en}
}
@inproceedings{KahmannHacklWegmannetal.2016,
  author    = {Kahmann, Stephanie and Hackl, Michael and Wegmann, Kilian and M{\"u}ller, Lars-Peter and Staat, Manfred},
  title     = {Impact of a proximal radial shortening osteotomy on the distribution of forces and the stability of the elbow},
  series = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  booktitle = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  editor    = {Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  doi       = {10.17185/duepublico/40821},
  pages     = {7 -- 8},
  year      = {2016},
  abstract  = {The human arm consists of the humerus (upper arm), the medial ulna and the lateral radius (forearm). The joint between the humerus and the ulna is called humeroulnar joint and the joint between the humerus and the radius is called humeroradial joint. Lateral and medial collateral ligaments stabilize the elbow. Statistically, 2.5 out of 10,000 people suffer from radial head fractures [1]. In these fractures the cartilage is often affected. Caused by the injured cartilage, degenerative diseases like posttraumatic arthrosis may occur. The resulting pain and reduced range of motion have an impact on the patient's quality of life. Until now, there has not been a treatment which allows typical loads in daily life activities and offers good long-term results. A new surgical approach was developed with the motivation to reduce the progress of the posttraumatic arthrosis. Here, the radius is shortened by 3 mm in the proximal part [2]. By this means, the load of the radius is intended to be reduced due to a load shift to the ulna. Since the radius is the most important stabilizer of the elbow it has to be confirmed that the stability is not affected. In the first test (Fig. 1 left), pressure distributions within the humeroulnar and humeroradial joints a native and a shortened radius were measured using resistive pressure sensors (I5076 and I5027, Tekscan, USA). The humerus was loaded axially in a tension testing machine (Z010, Zwick Roell, Germany) in 50 N steps up to 400 N. From the humerus the load is transmitted through both the radius and the ulna into the hand which is fixed on the ground. In the second test (Fig. 1 right), the joint stability was investigated using a digital image correlation system to measure the displacement of the ulna. Here, the humerus is fixed with a desired flexion angle and the unconstrained forearm lies on the ground. A rope connects the load actuator with a hook fixed in the ulna. A guide roller is used so that the rope pulls the ulna horizontally when a tensile load is applied. This creates a moment about the elbow joint with a maximum value of 7.5 Nm. Measurements were performed with varying flexion angles (0°, 30°, 60°, 90°, 120°). For both tests and each measurement, seven specimens were used. Student's t-test was employed to determine whether the mean values of the measurements in native specimen and operated specimens differ significantly.},
  language  = {en}
}
@inproceedings{StaatDuong2016,
  author    = {Staat, Manfred and Duong, Minh Tuan},
  title     = {Smoothed Finite Element Methods for Nonlinear Solid Mechanics Problems: 2D and 3D Case Studies},
  series = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2},
  booktitle = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2},
  pages     = {440 -- 445},
  year      = {2016},
  abstract  = {The Smoothed Finite Element Method (SFEM) is presented as an edge-based and a facebased techniques for 2D and 3D boundary value problems, respectively. SFEMs avoid shortcomings of the standard Finite Element Method (FEM) with lower order elements such as overly stiff behavior, poor stress solution, and locking effects. Based on the idea of averaging spatially the standard strain field of the FEM over so-called smoothing domains SFEM calculates the stiffness matrix for the same number of degrees of freedom (DOFs) as those of the FEM. However, the SFEMs significantly improve accuracy and convergence even for distorted meshes and/or nearly incompressible materials. Numerical results of the SFEMs for a cardiac tissue membrane (thin plate inflation) and an artery (tension of 3D tube) show clearly their advantageous properties in improving accuracy particularly for the distorted meshes and avoiding shear locking effects.},
  language  = {en}
}
@inproceedings{TranTranMatthiesetal.2016,
  author    = {Tran, Ngoc Trinh and Tran, Thanh Ngoc and Matthies, Hermann G. and Stavroulakis, Georgios Eleftherios and Staat, Manfred},
  title     = {FEM Shakedown of uncertain structures by chance constrained programming},
  series = {PAMM Proceedings in Applied Mathematics and Mechanics},
  volume    = {16},
  booktitle = {PAMM Proceedings in Applied Mathematics and Mechanics},
  number    = {1},
  issn      = {1617-7061},
  doi       = {10.1002/pamm.201610346},
  pages     = {715 -- 716},
  year      = {2016},
  language  = {en}
}
@article{LeversStaatLaack2016,
  author    = {Levers, A. and Staat, Manfred and Laack, Walter van},
  title     = {Analysis of the long-term effect of the MBST® nuclear magnetic resonance therapy on gonarthrosis},
  series = {Orthopedic Practice},
  volume    = {47},
  journal   = {Orthopedic Practice},
  number    = {11},
  pages     = {521 -- 528},
  year      = {2016},
  language  = {en}
}
@article{NiedermeyerZhouDursunetal.2016,
  author    = {Niedermeyer, Angela and Zhou, Bei and Dursun, G{\"o}zde and Temiz Artmann, Ayseg{\"u}l and Markert, Bernd},
  title     = {An examination of tissue engineered scaffolds in a bioreactor},
  series = {Proceedings in Applied Mathematics and Mechanics PAMM},
  volume    = {16},
  journal   = {Proceedings in Applied Mathematics and Mechanics PAMM},
  number    = {1},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1617-7061},
  doi       = {10.1002/pamm.201610038},
  pages     = {99 -- 100},
  year      = {2016},
  abstract  = {Replacement tissues, designed to fill in articular cartilage defects, should exhibit the same properties as the native material. The aim of this study is to foster the understanding of, firstly, the mechanical behavior of the material itself and, secondly, the influence of cultivation parameters on cell seeded implants as well as on cell migration into acellular implants. In this study, acellular cartilage replacement material is theoretically, numerically and experimentally investigated regarding its viscoelastic properties, where a phenomenological model for practical applications is developed. Furthermore, remodeling and cell migration are investigated.},
  language  = {en}
}
@inproceedings{DuongJungFrotscheretal.2016,
  author    = {Duong, Minh Tuan and Jung, Alexander and Frotscher, Ralf and Staat, Manfred},
  title     = {A 3D electromechanical FEM-based model for cardiac tissue},
  series = {ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5-10 June 2016},
  booktitle = {ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5-10 June 2016},
  editor    = {Papadrakakis, M.},
  pages     = {13 S.},
  year      = {2016},
  language  = {en}
}
@inproceedings{TranTranMatthiesetal.2016,
  author    = {Tran, Ngoc Trinh and Tran, Thanh Ngoc and Matthies, H. G. and Stavroulakis, G. E. and Staat, Manfred},
  title     = {Shakedown analysis of plate bending analysis under stochastic uncertainty by chance constrained programming},
  series = {ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5-10 June 2016},
  booktitle = {ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5-10 June 2016},
  editor    = {Papadrakakis, M.},
  pages     = {13 S.},
  year      = {2016},
  language  = {en}
}