@inproceedings{WagnerKohlFroebaetal.2006,
  author    = {Wagner, Thorsten and Kohl, Claus-Dieter and Fr{\"o}ba, Michael and Tiemann, Michael},
  title     = {Gas sensing properties of ordered mesoporous SnO2},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1422},
  year      = {2006},
  abstract  = {We report on the synthesis and CO gas-sensing properties of mesoporous tin(IV) oxides (SnO2). For the synthesis cetyltrimethylammonium bromide (CTABr) was used as a structure-directing agent; the resulting SnO2 powders were applied as films to commercially available sensor substrates by drop coating. Nitrogen physisorption shows specific surface areas up to 160 m2·g-1 and mean pore diameters of about 4 nm, as verified by TEM. The film conductance was measured in dependence on the CO concentration in humid synthetic air at a constant temperature of 300 °C. The sensors show a high sensitivity at low CO concentrations and turn out to be largely insensitive towards changes in the relative humidity. We compare the materials with commercially available SnO2-based sensors.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{MirmohseniRostamizadeh2006,
  author    = {Mirmohseni, Abdolreza and Rostamizadeh, Kobra},
  title     = {Quartz crystal nanobalance in conjunction with principal component analysis for identification of volatile organic compounds},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1434},
  year      = {2006},
  abstract  = {Quartz crystal nanobalance (QCN) sensors are considered as powerful masssensitive sensors to determine materials in the sub-nanogram level. In this study, a single piezoelectric quartz crystal nanobalance modified with polystyrene was employed to detect benzene, toluene, ethylbenzene and xylene (BTEX compounds). The frequency shift of the QCN sensor was found to be linear against the BTEX compound concentrations in the range about 1-45 mg l-1. The correlation coefficients for benzene, toluene, ethylbenzene, and xylene were 0.991, 0.9977, 0.9946 and 0.9971, respectively. The principal component analysis was also utilized to process the frequency response data of the single piezoelectric crystal at different times, considering to the different adsorption-desorption dynamics of BTEX compounds. Using principal component analysis, it was found that over 90\% of the data variance could still be explained by use of two principal components (PC1 and PC2). Subsequently, the successful identification of benzene and toluene was possible through the principal component analysis of the transient responses of the polystyrene modified QCN sensor. The results showed that the polystyrene-modified QCN had favorable identification and quantification performances for the BTEX compounds.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{KreutzLoergenGraeweetal.2006,
  author    = {Kreutz, Christian and L{\"o}rgen, J{\"u}rgen and Graewe, Boris and Bargon, Joachim and Yoshida, Mayumi and Freso, Zachary M. and Fr{\`e}chet, Jean M. J.},
  title     = {High frequency quartz micro balances: a promising path to enhanced sensitivity of gravimetric sensors},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1445},
  year      = {2006},
  abstract  = {An array of 50 MHz quartz microbalances (QMBs) coated with a dendronized polymer was used to detect small amounts of volatile organic compounds (VOCs) in the gas phase. The results were compared to those obtained with the commonly used 10 MHz QMBs. The 50 MHz QMBs proved to be a powerful tool for the detection of VOCs in the gas phase; therefore, they represent a promising alternative to the much more delicate surface acoustic wave devices (SAWs).},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{RabnerShacham2006,
  author    = {Rabner, Arthur and Shacham, Yosi},
  title     = {A concept for a sensitive micro total analysis system for high throughput fluorescence imaging},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1456},
  year      = {2006},
  abstract  = {This paper discusses possible methods for on-chip fluorescent imaging for integrated bio-sensors. The integration of optical and electro-optical accessories, according to suggested methods, can improve the performance of fluorescence imaging. It can boost the signal to background ratio by a few orders of magnitudes in comparison to conventional discrete setups. The methods that are present in this paper are oriented towards building reproducible arrays for high-throughput micro total analysis systems (µTAS). The first method relates to side illumination of the fluorescent material placed into microcompartments of the lab-on-chip. Its significance is in high utilization of excitation energy for low concentration of fluorescent material. The utilization of a transparent µLED chip, for the second method, allows the placement of the excitation light sources on the same optical axis with emission detector, such that the excitation and emission rays are directed controversly. The third method presents a spatial filtering of the excitation background.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{FoersterStockMontanarietal.2006,
  author    = {F{\"o}rster, Arnold and Stock, J{\"u}rgen and Montanari, Simone and Lepsa, Mihail Ion and L{\"u}th, Hans},
  title     = {Fabrication and characterisation of GaAs Gunn Diode Chips for applications at 77 GHz in automotive industry},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1462},
  year      = {2006},
  abstract  = {GaAs-based Gunn diodes with graded AlGaAs hot electron injector heterostructures have been developed under the special needs in automotive applications. The fabrication of the Gunn diode chips was based on total substrate removal and processing of integrated Au heat sinks. Especially, the thermal and RF behavior of the diodes have been analyzed by DC, impedance and S-parameter measurements. The electrical investigations have revealed the functionality of the hot electron injector. An optimized layer structure could fulfill the requirements in adaptive cruise control (ACC) systems at 77 GHz with typical output power between 50 and 90 mW.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{PlatenPoghossianSchoening2006,
  author    = {Platen, Johannes and Poghossian, Arshak and Sch{\"o}ning, Michael Josef},
  title     = {Microstructured Nanostructures - nanostructuring by means of conventional photolithography and layer-expansion technique},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1477},
  year      = {2006},
  abstract  = {A new and simple method for nanostructuring using conventional photolithography and layer expansion or pattern-size reduction technique is presented, which can further be applied for the fabrication of different nanostructures and nano-devices. The method is based on the conversion of a photolithographically patterned metal layer to a metal-oxide mask with improved pattern-size resolution using thermal oxidation. With this technique, the pattern size can be scaled down to several nanometer dimensions. The proposed method is experimentally demonstrated by preparing nanostructures with different configurations and layouts, like circles, rectangles, trapezoids, "fluidic-channel"-, "cantilever"- and meander-type structures.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{PijanowskaRemiszewskaPederzollietal.2006,
  author    = {Pijanowska, Dorota G. and Remiszewska, Elzbieta and Pederzolli, Cecilia and Lunelli, Lorenzo and Vendano, Michele and Canteri, Roberto and Dudzinski, Konrad and Kruk, Jerzy and Torbicz, Wladyslaw},
  title     = {Surface modification for microreactor fabrication},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1480},
  year      = {2006},
  abstract  = {In this paper, methods of surface modification of different supports, i.e. glass and polymeric beads for enzyme immobilisation are described. The developed method of enzyme immobilisation is based on Schiff's base formation between the amino groups on the enzyme surface and the aldehyde groups on the chemically modified surface of the supports. The surface of silicon modified by APTS and GOPS with immobilised enzyme was characterised by atomic force microscopy (AFM), time-of-flight secondary ion mass spectroscopy (ToF-SIMS) and infrared spectroscopy (FTIR). The supports with immobilised enzyme (urease) were also tested in combination with microreactors fabricated in silicon and Perspex, operating in a flow-through system. For microreactors filled with urease immobilised on glass beads (Sigma) and on polymeric beads (PAN), a very high and stable signal (pH change) was obtained. The developed method of urease immobilisation can be stated to be very effective.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{BukhariYang2006,
  author    = {Bukhari, Syed Faisal Ahmed and Yang, Wuqiang},
  title     = {Multi-interface level sensors and new development in monitoring and control of oil separators},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1498},
  year      = {2006},
  abstract  = {In the oil industry, huge saving may be made if suitable multi-interface level measurement systems are employed for effectively monitoring crude oil separators and efficient control of their operation. A number of techniques, e.g. externally mounted displacers, differential pressure transmitters and capacitance rod devices, have been developed to measure the separation process with gas, oil, water and other components. Because of the unavailability of suitable multi-interface level measurement systems, oil separators are currently operated by the trial-and-error approach. In this paper some conventional techniques, which have been used for level measurement in industry, and new development are discussed.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{TymeckiGlabKoncki2006,
  author    = {Tymecki, Lukasz and Glab, Stanislaw and Koncki, Robert},
  title     = {Miniaturized, planar ion-selective electrodes fabricated by means of thick-film technology},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1506},
  year      = {2006},
  abstract  = {Various planar technologies are employed for developing solid-state sensors having low cost, small size and high reproducibility; thin- and thick-film technologies are most suitable for such productions. Screen-printing is especially suitable due to its simplicity, low-cost, high reproducibility and efficiency in large-scale production. This technology enables the deposition of a thick layer and allows precise pattern control. Moreover, this is a highly economic technology, saving large amounts of the used inks. In the course of repetitions of the film-deposition procedure there is no waste of material due to additivity of this thick-film technology. Finally, the thick films can be easily and quickly deposited on inexpensive substrates. In this contribution, thick-film ion-selective electrodes based on ionophores as well as crystalline ion-selective materials dedicated for potentiometric measurements are demonstrated. Analytical parameters of these sensors are comparable with those reported for conventional potentiometric electrodes. All mentioned thick-film strip electrodes have been totally fabricated in only one, fully automated thickfilm technology, without any additional manual, chemical or electrochemical steps. In all cases simple, inexpensive, commercially available materials, i.e. flexible, plastic substrates and easily cured polymer-based pastes were used.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{SpannhakeSchulzHelwigetal.2006,
  author    = {Spannhake, Jan and Schulz, Olaf and Helwig, Andreas and Krenkow, Angelika and M{\"u}ller, Gerhard and Doll, Theodor},
  title     = {High-temperature MEMS heater platforms: long-term performance of metal and semiconductor heater materials},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1513},
  year      = {2006},
  abstract  = {Micromachined thermal heater platforms offer low electrical power consumption and high modulation speed, i.e. properties which are advantageous for realizing nondispersive infrared (NDIR) gas- and liquid monitoring systems. In this paper, we report on investigations on silicon-on-insulator (SOI) based infrared (IR) emitter devices heated by employing different kinds of metallic and semiconductor heater materials. Our results clearly reveal the superior high-temperature performance of semiconductor over metallic heater materials. Long-term stable emitter operation in the vicinity of 1300 K could be attained using heavily antimony-doped tin dioxide (SnO2:Sb) heater elements.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{KatzWillner2006,
  author    = {Katz, Eugenii and Willner, Itamar},
  title     = {Magneto-controlled quantized electron transfer to surface-confined redox units and metal nanoparticles},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1528},
  year      = {2006},
  abstract  = {Hydrophobic magnetic nanoparticles (NPs) consisting of undecanoate-capped magnetite (Fe3O4, average diameter ca. 5 nm) are used to control quantized electron transfer to surface-confined redox units and metal NPs. A two-phase system consisting of an aqueous electrolyte solution and a toluene phase that includes the suspended undecanoatecapped magnetic NPs is used to control the interfacial properties of the electrode surface. The attracted magnetic NPs form a hydrophobic layer on the electrode surface resulting in the change of the mechanisms of the surface-confined electrochemical processes. A quinone-monolayer modified Au electrode demonstrates an aqueous-type of the electrochemical process (2e-+2H+ redox mechanism) for the quinone units in the absence of the hydrophobic magnetic NPs, while the attraction of the magnetic NPs to the surface results in the stepwise single-electron transfer mechanism characteristic of a dry nonaqueous medium. Also, the attraction of the hydrophobic magnetic NPs to the Au electrode surface modified with Au NPs (ca. 1.4 nm) yields a microenvironment with a low dielectric constant that results in the single-electron quantum charging of the Au NPs.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{PijanowskaRemiszewska2006,
  author    = {Pijanowska, Dorota G. and Remiszewska, Elzbieta},
  title     = {pH-based detection of phenylalnine by potentiometric and colorimetric methods},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1536},
  year      = {2006},
  abstract  = {In this paper, methods of sample preparation for potentiometric measurement of phenylalanine are presented. Basing on the spectrophotometric measurements of phenylalanine, the concentrations of reagents of the enzymatic reaction (10 mM L-Phe, 0,4 mM NAD+, 2U L-PheDH) were determined. Then, the absorption spectrum of the reaction product, NADH, was monitored (maximum peak at 340 nm). The results obtained by the spectrophotometric method were compared with the results obtained by the colourimetry, using pH indicators. The above-mentioned two methods will be used as references for potentiometric measurements of phenylalanine concentration.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{AridaKloockSchoening2006,
  author    = {Arida, Hassan A. and Kloock, Joachim P. and Sch{\"o}ning, Michael Josef},
  title     = {Novel organic membrane-based thin-film microsensors for the determination of heavy metal cations},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1545},
  year      = {2006},
  abstract  = {A first step towards the fabrication and electrochemical evaluation of thin-film microsensors based on organic PVC membranes for the determination of Hg(II), Cd(II), Pb(II) and Cu(II) ions in solutions has been realised. The membrane-coating mixture used in the preparation of this new type of microsensors is incorporating PVC as supporting matrix, o-nitrophenyloctylether (o-NPOE) as solvent mediator and a recently synthesized Hg[dimethylglyoxime(phene)]2+ and Bis-(4-hydroxyacetophenone)-ethylenediamine as electroactive materials for Hg(II) and Cd(II), respectively. A set of three commercialised ionophores for Cd(II), Pb(II) and Cu(II) has been also used for comparison. Thin-film microsensors based on these membranes showed a Nernstian response of slope (26-30 mV/dec.) for the respective tested cations. The potentiometric response characteristics (linear range, pH range, detection limit and response time) are comparable with those obtained by conventional membranes as well as coated wire electrodes prepared from the same membrane. The realisation of the new organic membrane-based thin-film microsensors overcomes the problem of an insufficient selectivity of solid-state-based thinfilm sensors.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{BarekFischerNavratiletal.2006,
  author    = {Barek, Jiri and Fischer, Jan and Navratil, Tomas and Peckova, Karolina and Yosypchuk, Bogdan},
  title     = {Silver solid amalgam electrodes as sensors for chemical carcinogens},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1554},
  year      = {2006},
  abstract  = {The applicability of differential pulse voltammetry (DPV) and adsorptive stripping voltammetry (AdSV) at a non-toxic meniscus-modified silver solid amalgam electrode (m-AgSAE) for the determination of trace amounts of genotoxic substances was demonstrated on the determination of micromolar and submicromolar concentrations of 3-nitrofluoranthene using methanol - 0.01 mol L-1 NaOH (9:1) mixture as a base electrolyte and of Ostazine Orange using 0.01 mol L-1 NaOH as a base electrolyte.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{BaronasIvanauskasKulys2006,
  author    = {Baronas, Romas and Ivanauskas, Feliksas and Kulys, Juozas},
  title     = {Mathematical modeling of biosensors based on an array of enzyme microreactors},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1569},
  year      = {2006},
  abstract  = {This paper presents a two-dimensional-in-space mathematical model of biosensors based on an array of enzyme microreactors immobilised on a single electrode. The modeling system acts under amperometric conditions. The microreactors were modeled by particles and by strips. The model is based on the diffusion equations containing a nonlinear term related to the Michaelis-Menten kinetics of the enzymatic reaction. The model involves three regions: an array of enzyme microreactors where enzyme reaction as well as mass transport by diffusion takes place, a diffusion limiting region where only the diffusion takes place, and a convective region, where the analyte concentration is maintained constant. Using computer simulation, the influence of the geometry of the microreactors and of the diffusion region on the biosensor response was investigated. The digital simulation was carried out using the finite difference technique.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{Wessling2007,
  author    = {Weßling, Matthias},
  title     = {Leadership Perspectives: Research Findings, Theories, Practical Experiences},
  year      = {2007},
  abstract  = {Leadership Perspectives: Research Findings, Theories, Practical Experiences: Results of Leadership Research and exemplarily application cases show the perspectives and consequences for leadership practice and the following requirements for executives in future.},
  subject      = {Leadership},
  language  = {en}
}
@inproceedings{Wessling2007,
  author    = {Weßling, Matthias},
  title     = {Motivation and Leadership - The Reiss-Profile of the 16 Basic Desires: Research results and managerial applications},
  year      = {2007},
  abstract  = {Recent Results of the scientific Reiss-Profile (16 basic desires) due to the concept of Prof. Dr. Steven Reiss (State University Ohio, U.S.A.), supplemented by the comparative analysis of empirical motivational profiles of european executives of various companies.},
  subject      = {Motivation},
  language  = {en}
}
@inproceedings{Wessling2007,
  author    = {Weßling, Matthias},
  title     = {Provocative Communication in Coaching and Leadership: scientific research and managerial applications of the Provocative Communication Style},
  year      = {2007},
  abstract  = {Concept, scientific research and managerial applications of Provocative Coaching, according to the „Provocative Therapy" of Prof. Dr. Frank Farrelly (University of Wisconsin, U.S.A) in terms of an application of the Provocative Communication Style in specific situations of practical leadership, especially in the role of a coach for their subordinates.},
  subject      = {Kommunikation},
  language  = {en}
}
@inproceedings{Wessling2006,
  author    = {Weßling, Matthias},
  title     = {Como motivar a si mesmo e aos outros - o valor dos 16 Motivos Vitais para Lideran{\c{c}}a},
  year      = {2006},
  abstract  = {O Perfil Reiss apresenta no resultado uma vis{\~a}o da estrutura dos motivos e impulsos de uma pessoa. O ponto de sa{\´i}da para a an{\´a}lise do resultado {\´e} o conhecimento de que os motivos vitais (= valores e metas de sobreviv{\^e}ncia) formam a moldura, na qual as compet{\^e}ncias e capacidades que uma pessoa possui possam se desabrochar de forma ideal. A partir desse princ{\´i}pio, n{\~a}o existe no Perfil Reiss nenhum resultado que se possa classificar como correto ou falso, nem como bom ou mau. Uma compara{\c{c}}{\~a}o entre o resultado do Perfil Reiss e o conte{\´u}do de uma atividade apresentada ou ambicionada d{\´a} informa{\c{c}}{\~a}o sobre at{\´e} que ponto a capacidade de rendimento de uma pessoa nessa posi{\c{c}}{\~a}o pode vir ou vir{\´a} a se desenvolver por um longo tempo.},
  subject      = {F{\"u}hrung},
  language  = {es}
}
@inproceedings{LeiMulchandaniChenetal.2006,
  author    = {Lei, Yu and Mulchandani, Priti and Chen, Wilfred and Mulchandani, Ashok},
  title     = {Biosensor for direct determination of fenitrothion and EPN using recombinant Pseudomonas putida JS444 with surface expressed organophosphorus hydrolase. 1. modified clark oxygen electrode},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1573},
  year      = {2006},
  abstract  = {This paper reports a first microbial biosensor for rapid and cost-effective determination of organophosphorus pesticides fenitrothion and EPN. The biosensor consisted of recombinant PNP-degrading/oxidizing bacteria Pseudomonas putida JS444 anchoring and displaying organophosphorus hydrolase (OPH) on its cell surface as biological sensing element and a dissolved oxygen electrode as the transducer. Surfaceexpressed OPH catalyzed the hydrolysis of fenitrothion and EPN to release 3-methyl-4-nitrophenol and p-nitrophenol, respectively, which were oxidized by the enzymatic machinery of Pseudomonas putida JS444 to carbon dioxide while consuming oxygen, which was measured and correlated to the concentration of organophosphates. Under the optimum operating conditions, the biosensor was able to measure as low as 277 ppb of fenitrothion and 1.6 ppm of EPN without interference from phenolic compounds and other commonly used pesticides such as carbamate pesticides, triazine herbicides and organophosphate pesticides without nitrophenyl substituent. The applicability of the biosensor to lake water was also demonstrated.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{Roeth2002,
  author    = {R{\"o}th, Thilo},
  title     = {Modularisierung in der Karosserie von morgen},
  year      = {2002},
  abstract  = {1) Module werden die Fahrzeugplattform und den -aufbau in Zukunft weiterhin und in zunehmendem Maße bestimmen. 2) Neue Module und Modulschnittstellen am Fahrzeug werden {\"u}berdacht und k{\"o}nnen in der Zukunft erwartet werden. 3) Die Wertsch{\"o}pfung und der Entwicklungsumfang wird sich vom OEM zum Modullieferanten verlagern. 4) Modulvergaben werden in der Zukunft noch st{\"a}rker auf Innovation und Kostenreduktion beruhen. 5) Modularisierung des Fahrzeuges heißt ein Aufbrechen der Fahrzeugkarosserie und wird daher von der Beherrschung struktureller Aufgaben sowie der L{\"o}sung der (sichtbaren) Modul{\"u}berg{\"a}nge bestimmt sein. 6) Neben den Systemintegratoren und den Komponentenspezialisten besetzen die Modullieferanten die erste Lieferantenriege. 7) Der Modullieferant wird neben h{\"o}chster Fertigungsexpertise ein hohes Maß an (Teil-)fahrzeug-Know-How und Produktentwickler-mentalit{\"a}t bereitstellen.},
  subject      = {Karosseriebau},
  language  = {de}
}
@inproceedings{RoethTragsdorf2004,
  author    = {R{\"o}th, Thilo and Tragsdorf, Carsten},
  title     = {Innovativer Einsatz von Werkstoffen - Trends und Entwicklungen im Karosserieleichtbau},
  year      = {2004},
  abstract  = {1) In Karosseriestrukturen steht der richtige Werkstoffeinsatz st{\"a}rker den je im Spannungsfeld von Leichtbau, Kosten (St{\"u}ckzahlen) und Leistungsanforderung 2) In „klassischen" Strukturen von Modultr{\"a}gern und Klappen hat sich die Materialmischbauweise verst{\"a}rkt in den letzten Jahren durchgesetzt 3) Unter Aspekten des konzeptionellen Leichtbaus erscheint der verst{\"a}rkte Einsatz von Leichtbauwerkstoffen im Vorderwagen sowie in der Dachstruktur zielf{\"u}hrend 4) Offene Strukturprofile in Materialmischbauweise liefern f{\"u}r eine Vielzahl von Anwendungen ein interessantes und bis dato kaum genutztes Potential 5) Neue Entwicklungen bei den F{\"u}getechnologien (i.b. kontinuierliche F{\"u}geverbindungen und kombinierte Verfahren) unterst{\"u}tzen den wirtschaftlichen Karosserieleichtbau 6) Werkstoffinnovationen sowie neuartige Fertigungsverfahren machen den Konstruktionswerkstoff „Stahl" auch in der Zukunft im Karosseriebau weiterhin sehr attraktiv},
  subject      = {Karosseriebau},
  language  = {de}
}
@inproceedings{BuehrigPolaczekRoethBaumeisteretal.2006,
  author    = {B{\"u}hrig-Polaczek, Andreas and R{\"o}th, Thilo and Baumeister, E. and Nowack, N. and S{\"u}ßmann, Torsten},
  title     = {Hybride Leichtbaustrukturen in Stahlblech-Leichtmetall Verbundguss},
  year      = {2006},
  abstract  = {Stahl-Leichtmetall-Hybride mit hohen Leistungspotentialen k{\"o}nnen heute wirtschaftlich abgebildet werden und eignen sich m{\"o}glicherweise auch zum Einsatz in Fahrzeugkarosserien},
  subject      = {Karosseriebau},
  language  = {de}
}
@inproceedings{Staat2006,
  author    = {Staat, Manfred},
  title     = {Problems and chances for probabilistic fracture mechanics in the analysis of steel pressure boundary reliability. - {\"U}berarb. Ausg.},
  year      = {2006},
  abstract  = {In: Technical feasibility and reliability of passive safety systems for nuclear power plants. Proceedings of an Advisory Group Meeting held in J{\"u}lich, 21-24 November 1994. - Vienna , 1996. - Seite: 43 - 55 IAEA-TECDOC-920 Abstract: It is shown that the difficulty for probabilistic fracture mechanics (PFM) is the general problem of the high reliability of a small population. There is no way around the problem as yet. Therefore what PFM can contribute to the reliability of steel pressure boundaries is demon­strated with the example of a typical reactor pressure vessel and critically discussed. Although no method is distinguishable that could give exact failure probabilities, PFM has several addi­tional chances. Upper limits for failure probability may be obtained together with trends for design and operating conditions. Further, PFM can identify the most sensitive parameters, improved control of which would increase reliability. Thus PFM should play a vital role in the analysis of steel pressure boundaries despite all shortcomings.},
  subject      = {Bruchmechanik},
  language  = {en}
}
@inproceedings{Becker2006,
  author    = {Becker, Astrid},
  title     = {Anlagenmanagement und Aufgaben der DB Netz AG, Bauherrenvertretung und Wirtschaftlichkeit},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 18 {\"U}bersicht des Vortrags},
  subject      = {Anlagenwirtschaft},
  language  = {de}
}
@inproceedings{Wellmann2006,
  author    = {Wellmann, Judith},
  title     = {Perspektiven eines Bauingenieurs im konstruktiven Ingenieurbau},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 7-12 Die Berufsperspektiven im konstruktiven Ingenieurbau werden trotz sinkendem Bedarf an Statikern positiv bewertet.},
  subject      = {Ingenieurbau},
  language  = {de}
}
@inproceedings{OPUS4-161,
  title     = {Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006},
  organization    = {Alfha.net / Sektion Bauingenieurwesen},
  year      = {2006},
  abstract  = {"Mit dem "1. Erfahrungsaustausch" im Fachbereich Bauingenieurwesen berichten Absolventen des Fachbereichs aus der Praxis. Mit diesem Treffen wird die wichtige Verbindung zwischen Hochschule, ihren Absolventen und der Berufspraxis zum besonderen Anliegen gemacht und besonders gest{\"a}rkt." Zitat Prof. Dr.- Ing. Hans Boegershausen, Dekan im Grußwort. Referenten und Themen: Wellmann, Judith: Perspektiven eines Bauingenieurs im konstruktiven Ingenieurbau Dirk Gobbele, Dirk: Planung der Umbaumaßnahme Hauptbahnhof Aachen Kretschmann, Lars: Planung und Bauleitung Buschtunnel Aachen Becker, Astrid: Anlagenmanagement und Aufgaben der DB Netz AG, Bauherrenvertretung und Wirtschaftlichkeit Plenz, Michael: Baurevision und Unternehmensberatung, T{\"a}tigkeit als {\"o}ffentlich bestellter und vereidigter Sachverst{\"a}ndiger Kl{\"o}cker, Alexander: Das Leitungsbauunternehmen - Unternehmerische Strategie als Zukunftssicherung T{\"u}rk, Roman: Sanierung von Hausanschl{\"u}ssen Bornebusch, Michael: Hydraulische und Hydrologische Modellsimulationen als Planungswerkzeug f{\"u}r Hochwasser-Schutz-Maßnahmen Himmerich, J{\"o}rg : Pipeline Integrity Management System - Probabilistische Bewertung von Bauwerken am Beispiel von Hochdruckleitungen.},
  subject      = {Aachen / Fachhochschule Aachen / Fachbereich Bauingenieurwesen},
  language  = {de}
}
@inproceedings{Gobbele2006,
  author    = {Gobbel{\´e}, Dirk},
  title     = {Planung der Umbaumaßnahme Hauptbahnhof Aachen},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 13-15. Bericht {\"u}ber die infrastrukturellen Maßnahmen zum Umbau des Hauptbahnhofs Aachen.},
  subject      = {Bauplanung},
  language  = {de}
}
@inproceedings{Kretschmann2006,
  author    = {Kretschmann, Lars},
  title     = {Planung und Bauleitung Buschtunnel Aachen},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 16-17 Der Umbau des Aachener Buschtunnels im Rahmen des europ{\"a}ischen Hochgeschwindigkeitsschienennetzes wird im sogenannten "Neuen {\"O}sterreichischen Tunnelbauverfahren (NOeT)", also ein Ausbau in Kalotte, Strosse und Sohle durchgef{\"u}hrt.},
  subject      = {Bauplanung},
  language  = {de}
}
@inproceedings{Plenz2006,
  author    = {Plenz, Michael},
  title     = {Baurevision und Unternehmensberatung, T{\"a}tigkeit als {\"o}ffentlich bestellter und vereidigter Sachverst{\"a}ndiger},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 19-20. Zusammenfassung des Vortrags: Prozessanalyse und Revision beim Umbau des Flughafens Hamburg, Beratung von Bauunternehmen, Sachverst{\"a}ndigent{\"a}tigkeit},
  subject      = {{\"O}ffentlich bestellter Sachverst{\"a}ndiger},
  language  = {de}
}
@inproceedings{Kloecker2006,
  author    = {Kl{\"o}cker, Alexander},
  title     = {Das Leitungsbauunternehmen - unternehmerische Strategie als Zukunftssicherung},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 21-22 Zusammenfassung des Vortrags},
  subject      = {Leitungsbau},
  language  = {de}
}
@inproceedings{Tuerk2006,
  author    = {T{\"u}rk, Roman},
  title     = {Sanierung von Hausanschl{\"u}ssen},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 23-24. Zusammenfassung des Vortrags.},
  subject      = {Hausanschluss},
  language  = {de}
}
@inproceedings{SchuermannKellerWollert2009,
  author    = {Sch{\"u}rmann, Volker and Keller, Alex and Wollert, J{\"o}rg},
  title     = {Konvergenz von drahtlosen und drahtgebundenen Kommunikationstechnologien in der Geb{\"a}udeautomation},
  series = {Wireless technologies : von der Technologie zur Anwendung ; 11. Kongress, 29. - 30. September 2009, Stuttgart / [11. Wireless-Technologies-Kongress]. (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 800)},
  booktitle = {Wireless technologies : von der Technologie zur Anwendung ; 11. Kongress, 29. - 30. September 2009, Stuttgart / [11. Wireless-Technologies-Kongress]. (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; Nr. 800)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Wireless-Technologies-Kongress <11, 2009, Stuttgart>},
  isbn      = {978-3-18-380010-0},
  pages     = {197 -- 205},
  year      = {2009},
  language  = {de}
}
@inproceedings{SchuermannLeidingerWollert2010,
  author    = {Sch{\"u}rmann, Volker and Leidinger, R. and Wollert, J{\"o}rg},
  title     = {Simplified rapid-prototyping with automation technology},
  series = {Automobiles and sustainable mobility : FISITA 2010 World Automotive Congress, 30 May - 4 June, Budapest, Hungary ; proceedings},
  booktitle = {Automobiles and sustainable mobility : FISITA 2010 World Automotive Congress, 30 May - 4 June, Budapest, Hungary ; proceedings},
  organization    = {FISITA 2010 World Automotive Congress <Budapest>},
  isbn      = {978-963-9058-29-3},
  pages     = {F2010C093},
  year      = {2010},
  language  = {en}
}
@inproceedings{StieglitzWollert2010,
  author    = {Stieglitz, Kristian and Wollert, J{\"o}rg},
  title     = {Database driven modernization and expansion of storage systems},
  series = {Proceedings : the 3rd International Multi-Conference on Engineering and Technological Innovation : June 29th - July 2nd, 2010, Orlando, Florida, USA ; vol. 2},
  booktitle = {Proceedings : the 3rd International Multi-Conference on Engineering and Technological Innovation : June 29th - July 2nd, 2010, Orlando, Florida, USA ; vol. 2},
  publisher = {IIIS},
  address   = {Winter Garden, Fla.},
  organization    = {International Multi-Conference on Engineering and Technological Innovation <3, 2010, Orlando, Fla.>},
  isbn      = {978-1-936338-03-0},
  pages     = {180 -- 183},
  year      = {2010},
  language  = {de}
}
@inproceedings{SchuermannLeidingerWollert2010,
  author    = {Sch{\"u}rmann, Volker and Leidinger, Rafael and Wollert, J{\"o}rg},
  title     = {Intelligent IO-Terminals for complex communication scenarios in control applications},
  series = {Proceedings : the 3rd International Multi-Conference on Engineering and Technological Innovation : June 29th - July 2nd, 2010, Orlando, Florida, USA},
  booktitle = {Proceedings : the 3rd International Multi-Conference on Engineering and Technological Innovation : June 29th - July 2nd, 2010, Orlando, Florida, USA},
  organization    = {International Multi-Conference on Engineering and Technological Innovation <3, 2010, Orlando, Fla.>},
  pages     = {1 -- 5},
  year      = {2010},
  language  = {de}
}
@inproceedings{KraftZoell2014,
  author    = {Kraft, Bodo and Z{\"o}ll, Axel},
  title     = {Von der Langstrecke zum Sprint - Agile Methoden in traditionellen Unternehmen},
  series = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung},
  booktitle = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung},
  editor    = {Engstler, Martin},
  publisher = {Gesellschaft f{\"u}r Informatik},
  address   = {Bonn},
  organization    = {FH Aachen, University of Applied Sciences},
  isbn      = {978-3-88579-630-5},
  pages     = {35 -- 46},
  year      = {2014},
  language  = {de}
}
@inproceedings{KirchhofKraft2011,
  author    = {Kirchhof, Michael and Kraft, Bodo},
  title     = {Dogmatisches „Entweder agil oder klassisch" im Projektmanagement hat ausgedient - die richtige Mischung macht's},
  series = {Projekt-Sternstunden : strahlende Erfolge durch Kompetenz},
  booktitle = {Projekt-Sternstunden : strahlende Erfolge durch Kompetenz},
  publisher = {GPM},
  address   = {N{\"u}rnberg},
  isbn      = {978-3-924841-60-7},
  pages     = {414 -- 425},
  year      = {2011},
  language  = {de}
}
@inproceedings{MorenoDosevBratovetal.2006,
  author    = {Moreno, Lia and Dosev, D. and Bratov, A. and Dominguez, C. and Sch{\"o}ning, Michael Josef and Kloock, Joachim P.},
  title     = {Effect of electrical properties of the surrounding medium on the response of an interdigitated electrode array with chalcogenide glass film},
  series = {XX Eurosensors : 20th anniversary ; G{\"o}teborg, Sweden, 17 - 20 September 2006 ; [proceedings]. - Vol. 1},
  booktitle = {XX Eurosensors : 20th anniversary ; G{\"o}teborg, Sweden, 17 - 20 September 2006 ; [proceedings]. - Vol. 1},
  address   = {G{\"o}teborg},
  isbn      = {978-91-631-9280-7},
  pages     = {384 -- 385},
  year      = {2006},
  language  = {en}
}
@inproceedings{Huening2014,
  author    = {H{\"u}ning, Felix},
  title     = {Power semiconductors : key components for HEV/EV},
  series = {FISITA 2014 World Automotive Congress : 2 - 6 June, Maastricht, the Netherlands International Federation of Automotive Engineering Societies},
  booktitle = {FISITA 2014 World Automotive Congress : 2 - 6 June, Maastricht, the Netherlands International Federation of Automotive Engineering Societies},
  publisher = {KIVI},
  address   = {[s.l.]},
  pages     = {1 USB-Speicherstick},
  year      = {2014},
  language  = {en}
}
@inproceedings{BudaWollert2011,
  author    = {Buda, Aurel and Wollert, J{\"o}rg},
  title     = {Leistungsbewertung von Ultra Wideband Funktechnologien nach ECMA 368 f{\"u}r den Einsatz in industriellen Kommunikationssystemen},
  series = {Kommunikation in der Automation : Magdeburg, 27. - 28.09.2011 ; 2. Jahreskolloquium Kommunikation in der Automation ; KOMMA 2011 / Ulrich Jumar ... (Hrsg.)},
  booktitle = {Kommunikation in der Automation : Magdeburg, 27. - 28.09.2011 ; 2. Jahreskolloquium Kommunikation in der Automation ; KOMMA 2011 / Ulrich Jumar ... (Hrsg.)},
  publisher = {ifak, Institut f{\"u}r Automation und Kommunikation e.V. Magdeburg an der Otto-von-Guericke-Universit{\"a}t Magdeburg},
  address   = {Magdeburg},
  organization    = {Jahreskolloquium Kommunikation in der Automation <2, 2011, Magdeburg>},
  isbn      = {978-3-940961-58-7},
  pages     = {1 CD-ROM},
  year      = {2011},
  language  = {de}
}
@inproceedings{StieglitzWollert2011,
  author    = {Stieglitz, Kristian and Wollert, J{\"o}rg},
  title     = {Approach of using ultra-wideband-radio in industrial real-time ethernet networks},
  series = {The 4th International Multi-Conference on Engineering and Technological Innovation : IMETI : July 19th - July 22nd, 2011, Orlando, Florida, USA},
  booktitle = {The 4th International Multi-Conference on Engineering and Technological Innovation : IMETI : July 19th - July 22nd, 2011, Orlando, Florida, USA},
  organization    = {International Multi-Conference on Engineering and Technological Innovation <4, 2011, Orlando, Fla.>},
  pages     = {1 -- 6},
  year      = {2011},
  language  = {en}
}
@inproceedings{Wollert2012,
  author    = {Wollert, J{\"o}rg},
  title     = {The performance of UWB-communication in an industrial environment},
  series = {IEEE 1st International Symposium on Wireless Systems : (IDAACS-SWS) : Offenburg, 20-21 Sept. 2012},
  booktitle = {IEEE 1st International Symposium on Wireless Systems : (IDAACS-SWS) : Offenburg, 20-21 Sept. 2012},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  organization    = {International Symposium on Wireless Systems <1, 2012, Offenburg>},
  isbn      = {978-1-4673-4678-8},
  doi       = {10.1109/IDAACS-SWS.2012.6377639},
  pages     = {85 -- 90},
  year      = {2012},
  language  = {en}
}
@inproceedings{WollertRau2012,
  author    = {Wollert, J{\"o}rg and Rau, S.},
  title     = {Performance von embedded WLAN-Systemen bei koexistierenden Netzwerken},
  series = {KOMMA 2012 : Kommunikation in der Automation : 3. Jahreskolloquium Kommunikation in der Automation : Lemgo, 14.11.2012 / J{\"u}rgen Jasperneite ... (Hrsg.)},
  booktitle = {KOMMA 2012 : Kommunikation in der Automation : 3. Jahreskolloquium Kommunikation in der Automation : Lemgo, 14.11.2012 / J{\"u}rgen Jasperneite ... (Hrsg.)},
  publisher = {Inst. f{\"u}r Industrielle Informationstechnik},
  address   = {Lemgo},
  organization    = {Jahreskolloquium Kommunikation in der Automation <3, 2012, Lemgo>},
  isbn      = {978-3-9814062-2-1},
  pages     = {1 CD-ROM},
  year      = {2012},
  language  = {de}
}
@inproceedings{Goldbach2014,
  author    = {Goldbach, Daniel},
  title     = {Diagnosemaßnahmen im Umfeld der Funktionalen Sicherheit},
  series = {AmE 2014 - Automotive meets electronics [Elektronische Ressource] : Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund / Veranst.: VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)},
  booktitle = {AmE 2014 - Automotive meets electronics [Elektronische Ressource] : Beitr{\"a}ge der 5. GMM-Fachtagung vom 18. bis 19. Februar 2014 in Dortmund / Veranst.: VDE/VDI-Gesellschaft Mikroelektronik, Mikrosystem- und Feinwerktechnik (GMM)},
  editor    = {Wahl, Michael},
  publisher = {VDE-Verl.},
  address   = {Berlin},
  isbn      = {978-3-8007-3580-8},
  pages     = {172 -- 179},
  year      = {2014},
  language  = {de}
}
@inproceedings{BuschkuehleSchuermannWollert2009,
  author    = {Buschk{\"u}hle, Peter and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg},
  title     = {Abstraction of wireless communication by a convergence middleware in conjunction with a XML-configuration},
  series = {Information technology and electrical engineering : devices and systems, materials and technologies for the future ; Ilmenau 07 - 10 September 2009 ; 54. IWK Internationales Wissenschaftliches Kolloquium},
  booktitle = {Information technology and electrical engineering : devices and systems, materials and technologies for the future ; Ilmenau 07 - 10 September 2009 ; 54. IWK Internationales Wissenschaftliches Kolloquium},
  publisher = {Techn. Univ.},
  address   = {Ilmenau},
  isbn      = {978-3-938843-44-4},
  pages     = {95 -- 96},
  year      = {2009},
  language  = {en}
}
@inproceedings{AnthrakidisHerrmannMirzaetal.2014,
  author    = {Anthrakidis, Anette and Herrmann, Ulf and Mirza, M. F. and Schorn, Christian and Schwarzer, Klemens and Wedding, Philipp and Weis, Fabian},
  title     = {Parabolrinnenentwicklung und Qualifizierung am Solar-Institut J{\"u}lich},
  series = {Thermische Solarenergie : 24. Symposium ; 7. bis 9. Mai 2014, Kloster Banz, Bad Staffelstein},
  booktitle = {Thermische Solarenergie : 24. Symposium ; 7. bis 9. Mai 2014, Kloster Banz, Bad Staffelstein},
  publisher = {OTTI},
  address   = {Regensburg},
  organization    = {Ostbayerisches Technologie-Transfer-Institut},
  isbn      = {978-3-943891-35-5},
  pages     = {242 -- 243},
  year      = {2014},
  language  = {de}
}
@inproceedings{KronhardtAlexopoulosReisseletal.2015,
  author    = {Kronhardt, Valentina and Alexopoulos, Spiros and Reißel, Martin and Latzke, Markus and Rendon, C. and Sattler, Johannes, Christoph and Herrmann, Ulf},
  title     = {Simulation of operational management for the Solar Thermal Test and Demonstration Power Plant J{\"u}lich using optimized control strategies of the storage system},
  series = {Energy procedia},
  booktitle = {Energy procedia},
  issn      = {1876-6102},
  pages     = {1 -- 6},
  year      = {2015},
  language  = {en}
}
@inproceedings{BudaWollert2008,
  author    = {Buda, Aurel and Wollert, J{\"o}rg},
  title     = {Kompensation von Fading und Koexistenzproblemen in IEEE 802.15.4 Netzwerken durch Diversit{\"a}t : die Kombination macht's m{\"o}glich},
  series = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  booktitle = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Automatisierungskongress <2008, Baden-Baden>},
  isbn      = {978-3-18-092032-0},
  pages     = {139 -- 142},
  year      = {2008},
  language  = {de}
}
@inproceedings{SchuermannWollert2008,
  author    = {Sch{\"u}rmann, Volker and Wollert, J{\"o}rg},
  title     = {Ortsbezogene Fernwartungsdienste mit Bluetooth Ranging und Java Micro Edition},
  series = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  booktitle = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {Automatisierungskongress <2008, Baden-Baden>},
  isbn      = {978-3-18-092032-0},
  pages     = {353 -- 356},
  year      = {2008},
  language  = {de}
}