@incollection{Mertens1997, author = {Mertens, Josef}, title = {Supersonic laminar flow}, series = {New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366)}, booktitle = {New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366)}, editor = {Sobieczky, H.}, publisher = {Springer}, address = {Wien [u.a.]}, isbn = {3-2118-2815-X}, doi = {10.1007/978-3-7091-2658-5_18}, pages = {275 -- 290}, year = {1997}, abstract = {Supersonic transports are very drag sensitive. Technology to reduce drag by application of laminar flow, therefore, will be important; it is a prerequisite to achieve very long range capability. In earlier studies it was assumed that SCTs would only become possible by application of laminar flow [376]. But today, we request an SCT to be viable without application of laminar flow in order to maintain its competitiveness when laminar flow becomes available for subsonic and supersonic transports. By reducing fuel burned, laminar flow drag reduction reduces size and weight of the aircraft, or increases range capability -whereas otherwise size and weight would grow towards infinity. Transition mechanisms from laminar to turbulent state of the boundary layer flow (ALT, CFI, TSI) function as for transonic transports, but at more severe conditions: higher sweep angles, cooled surfaces; higher mode instabilities (HMI) must at least be taken into account, although they may not become important below Mach 3. Hitherto there is a worldwide lack of ground test facilities to investigate TSI at the expected cruise Mach numbers between 1.6 and 2.4; in Stuttgart, Germany one such facility -a Ludwieg tube- is still in the validation phase. A quiet Ludwieg tunnel could be a favourable choice for Europe. But it will require a new approach in designing aircraft which includes improved theoretical predictions, usage of classical wind tunnels for turbulent flow and flight tests for validation.}, language = {en} } @incollection{Mertens1997, author = {Mertens, Josef}, title = {Son of Concorde, a technology challenge}, series = {New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366)}, booktitle = {New design concepts for high speed air transport. - (Courses and lectures / International Centre for Mechanical Sciences ; 366)}, editor = {Sobieczky, H.}, publisher = {Springer}, address = {Wien [u.a.]}, isbn = {3-2118-2815-X}, doi = {10.1007/978-3-7091-2658-5_3}, pages = {31 -- 51}, year = {1997}, abstract = {Concorde (Figure 9) is the only supersonic airliner which has been introduced into regular passenger service. It is still in service at British Airways and Air France without any flight accidents, and probably will stay in service for at least for ten more years.}, language = {en} } @article{Mertens1985, author = {Mertens, Josef}, title = {Charakteristiken des Staub-Gas-Gemisches}, series = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4}, journal = {Zeitschrift f{\"u}r angewandte Mathematik und Mechanik : ZAMM. 65 (1985), H. 4}, isbn = {1521-4001}, pages = {T211 -- T213}, year = {1985}, language = {de} } @book{Mertens1983, author = {Mertens, Josef}, title = {Instation{\"a}re Str{\"o}mungen von Gasen mit brennbaren Partikeln}, address = {Aachen}, pages = {III, 245 S. : graph. Darst.}, year = {1983}, language = {de} } @inproceedings{Mertens2001, author = {Mertens, Josef}, title = {Next steps envisaged to improve wing performance of commercial aircraft}, series = {Aerodynamic drag reduction technologies : proceedings of the CEAS/DragNet European Drag Reduction Conference, 19-21 June 2000, Potsdam, Germany. - (Notes on numerical fluid mechanics ; 76)}, booktitle = {Aerodynamic drag reduction technologies : proceedings of the CEAS/DragNet European Drag Reduction Conference, 19-21 June 2000, Potsdam, Germany. - (Notes on numerical fluid mechanics ; 76)}, publisher = {Springer}, address = {Berlin [u.a.]}, isbn = {3-540-41911-X (Print)}, doi = {10.1007/978-3-540-45359-8_26}, pages = {246 -- 255}, year = {2001}, language = {en} } @incollection{Mertens1997, author = {Mertens, Josef}, title = {Reduction of aerodynamic drag (RaWid)-Status after the first year of the program}, series = {New results in numerical and experimental fluid mechanics. - (Notes on numerical fluid mechanics ; 60)}, booktitle = {New results in numerical and experimental fluid mechanics. - (Notes on numerical fluid mechanics ; 60)}, publisher = {Vieweg}, address = {Braunschweig [u.a.]}, isbn = {3-528-06960-0}, doi = {10.1007/978-3-322-86573-1_2}, pages = {7 -- 14}, year = {1997}, abstract = {The technology programme "Reduction of aerodynamic drag (RaWid)" for high speed aerodynamics at Daimler-Benz Aerospace Airbus is sponsered by the German ministry for education, research and technology since July 1, 1995. Connected to this industrial programme are the cooperation programmes "MEGAFLOW" under leadership of the DLR and "Transition" by the DFG, and several contributions by DLR and universities. The programme is oriented towards technologies required for a MEGALINER which gains momentum by the ambitious plans for a new large Airbus A3XX. In the first year new technological steps were undertaken in theory, design and experiment. Some critical steps were verified by wing designs checked in wind tunnel tests.}, language = {en} } @article{Mertens2006, author = {Mertens, Josef}, title = {Luft hat keine Balken, aber enorme Kr{\"a}fte : Aerodynamik - die unsichtbare Kraft}, series = {HEmagazin : das Hocheffizienz-Magazin von Wilo. 2006 (2006), H. 1}, journal = {HEmagazin : das Hocheffizienz-Magazin von Wilo. 2006 (2006), H. 1}, publisher = {-}, pages = {4 -- 9}, year = {2006}, language = {de} } @article{Mertens1998, author = {Mertens, Josef}, title = {Required technologies for supersonic aircraft}, series = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamic research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, journal = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamic research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, publisher = {Research and Technology Organization}, address = {Neuilly-sur-Seine}, isbn = {92-837-1007-X}, pages = {5.1 -- 5.16}, year = {1998}, language = {en} } @article{Mertens1998, author = {Mertens, Josef}, title = {Multi point design challenges for supersonic transports}, series = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamics research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, journal = {Fluid dynamics research on supersonic aircraft : this report is a compilation of the edited proceedings of the special course on "Fluid dynamics research on supersonic aircraft" held at the Karman Institute for Fluid Dynamics (VKI) in Rhode-Saint-Genese, Belgium, 25-29 May 1998}, publisher = {Research and Technology Organization}, address = {Neuilly-sur-Seine}, isbn = {92-837-1007-X}, pages = {8.1 -- 8.12}, year = {1998}, language = {en} } @article{Mertens1992, author = {Mertens, Josef}, title = {Laminar flow for supersonic transports}, series = {Proceedings : March 16 - 18, 1992, Congress Centrum, Hamburg, Federal Republic of Germany / organized jointly by: Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt e.V. ... [Programme committee J. Szodruch ...]}, journal = {Proceedings : March 16 - 18, 1992, Congress Centrum, Hamburg, Federal Republic of Germany / organized jointly by: Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt e.V. ... [Programme committee J. Szodruch ...]}, publisher = {DGLR}, address = {Bonn}, isbn = {3-922010-73-3}, pages = {319 -- 323}, year = {1992}, language = {en} } @article{Mertens1998, author = {Mertens, Josef}, title = {Aerodynamische Ziele des Adaptiven Fl{\"u}gels (ADIF).}, series = {DGLR-Jahrbuch 1998 Bd. 1}, journal = {DGLR-Jahrbuch 1998 Bd. 1}, pages = {47 -- 52}, year = {1998}, language = {de} } @article{Mertens1999, author = {Mertens, Josef}, title = {Einige herausragende Ergebnisse des Technologieprogramms "Reduktion des Aerodynamischen Widerstands (RaWid)"}, series = {DGLR-Jahrbuch 1999 Bd. 3}, journal = {DGLR-Jahrbuch 1999 Bd. 3}, pages = {1461 -- 1468}, year = {1999}, language = {de} } @book{Mertens1999, author = {Mertens, Josef}, title = {Reduktion des aerodynamischen Widerstands (RaWid) : Abschlußbericht ; Laufzeit des Vorhaben, Berichtszeitraum: 01.07.1995 bis 31.12.1998 / Verf.: J. Mertens}, publisher = {DaimlerChrysler Aerospare Airbus GmbH}, address = {Hamburg}, pages = {31 Bl. : Ill., graph. Darst.}, year = {1999}, language = {de} } @book{Mertens1999, author = {Mertens, Josef}, title = {Reduktion des aerodynamischen Widerstands (RaWid) : Abschlußbericht ; Laufzeit des Vorhaben, Berichtszeitraum: 01.07.1995 bis 31.12.1998 / Verf.: J. Mertens}, publisher = {DaimlerChrysler Aerospare Airbus GmbH}, address = {Hamburg}, pages = {Elektronische Ressource 31 p. = 1,38 Mb. text and}, year = {1999}, language = {de} } @inproceedings{Mertens1999, author = {Mertens, Josef}, title = {Some important results of the technology programme RaWid}, series = {New Results in Numerical and Experimental Fluid Mechanics : Contributions to the 11th AG STAB/DGLR Symposium Berlin, Germany 1998. - Vol. 2. - (Notes on Numerical Fluid Mechanics ; 72)}, booktitle = {New Results in Numerical and Experimental Fluid Mechanics : Contributions to the 11th AG STAB/DGLR Symposium Berlin, Germany 1998. - Vol. 2. - (Notes on Numerical Fluid Mechanics ; 72)}, editor = {Nitsche, Wolfgang}, publisher = {Springer Fachmedien}, address = {Wiesbaden}, isbn = {978-3-663-10903-7 (Print)}, doi = {10.1007/978-3-663-10901-3_41}, pages = {315 -- 322}, year = {1999}, language = {en} } @incollection{MertensBecker1989, author = {Mertens, Josef and Becker, K.}, title = {Numerical solution of flow equations : an aircraft designer's view}, series = {Nonlinear hyperbolic equations - theory, computation methods, and applications : proceedings of the 2nd International Conference on Nonlinear Hyperbolic Problems, Aachen, FRG, March 14 to 18, 1988. - (Notes on Numerical Fluid Mechanics ; 24)}, booktitle = {Nonlinear hyperbolic equations - theory, computation methods, and applications : proceedings of the 2nd International Conference on Nonlinear Hyperbolic Problems, Aachen, FRG, March 14 to 18, 1988. - (Notes on Numerical Fluid Mechanics ; 24)}, editor = {Ballmann, Josef}, publisher = {Vieweg}, address = {Braunschweig}, isbn = {3-528-08098-1}, doi = {10.1007/978-3-322-87869-4_41}, pages = {403 -- 412}, year = {1989}, abstract = {Today the most accurate and cost effective industrial codes used in aircraft design are based on the full potential equation coupled with boundary layer equations. However, these are not capable to solve complicated three-dimensional problems of vortical flows and shocks. On the other hand Euler and Navier-Stokes codes are too expensive and not accurate enough for design purposes, especially in regard of drag and interference prediction. The reasons for these deficiencies are investigated and a way to overcome them by future developments is demonstrated.}, language = {en} } @article{MertensHenke2001, author = {Mertens, Josef and Henke, Rolf}, title = {Adaptive technologies for future civil air transport}, series = {Air \& Space Europe. 3 (2001), H. 3-4}, journal = {Air \& Space Europe. 3 (2001), H. 3-4}, isbn = {1247-5793}, pages = {80 -- 82}, year = {2001}, language = {en} } @article{MertensHuenecke1988, author = {Mertens, Josef and H{\"u}necke, Klaus}, title = {Experimentelle Untersuchung zur Landeeigenschaft von Hyperschall-Flugger{\"a}ten / H{\"u}necke, Klaus ; Mertens, Josef}, series = {DGLR-Jahrbuch 1988 Bd. 1}, journal = {DGLR-Jahrbuch 1988 Bd. 1}, pages = {706}, year = {1988}, language = {de} } @article{MertensKelmVelden1999, author = {Mertens, Josef and Kelm, R. and Velden, A. van der}, title = {Interdisziplin{\"a}re Auslegung eines Verkehrsflugzeugfl{\"u}gels}, series = {DGLR-Jahrbuch 1999 Bd. 3}, journal = {DGLR-Jahrbuch 1999 Bd. 3}, pages = {1605 -- 1610}, year = {1999}, language = {de} } @article{MertensKlevenhusenJakob1987, author = {Mertens, Josef and Klevenhusen, K. D. and Jakob, H.}, title = {Accurate Transonic Wave Drag Prediction Using Simple Physical Models}, series = {AIAA-Journal. 25 (1987), H. 6}, journal = {AIAA-Journal. 25 (1987), H. 6}, isbn = {0001-1452}, pages = {799 -- 805}, year = {1987}, language = {en} } @misc{MertensLajain2002, author = {Mertens, Josef and Lajain, Henri}, title = {Method of fabricating leading edge nose structures of aerodynamic surfaces : patent no.: US 6,415,510 B2 ; date of patent: Jul. 9, 2002}, publisher = {United States Patent and Trademark Office}, address = {[Washington, DC]}, pages = {12 S. : Ill.}, year = {2002}, language = {en} } @article{MertensRoeger2000, author = {Mertens, Josef and R{\"o}ger, Wolf}, title = {F-Schlepp: Problem Taumelschwingung}, series = {Aerokurier. 44 (2000), H. 10}, journal = {Aerokurier. 44 (2000), H. 10}, isbn = {0341-1281}, pages = {73 -- 73}, year = {2000}, language = {de} } @misc{MertensVeldenKelm2006, author = {Mertens, Josef and Velden, Alexander van der and Kelm, Roland}, title = {Flugzeug mit Fl{\"u}geln, deren maximaler Auftrieb durch steuerbare Fl{\"u}gelkomponenten ver{\"a}nderbar ist : Offenlegungsschrift DE102004045732 ; Offenlegungstag: 30.03.2006 = Aircraft with wings whose maximum lift can be altered by controllable wing components}, publisher = {Deutsches Patent- und Markenamt}, address = {M{\"u}nchen}, pages = {6 S. : Ill.}, year = {2006}, language = {de} } @book{MertensVeldenKelmetal.2000, author = {Mertens, Josef and Velden, Alexander van der and Kelm, Roland and Kokan, David}, title = {Application of MDO to large subsonic transport aircraft}, publisher = {American Institute of Aeronautics and Astronautics}, address = {Reston, Va.}, pages = {12 S. : zahlr. Ill. u. graph. Darst.}, year = {2000}, language = {en} } @article{MeyerGranrathFeyerletal.2021, author = {Meyer, Max-Arno and Granrath, Christian and Feyerl, G{\"u}nter and Richenhagen, Johannes and Kaths, Jakob and Andert, Jakob}, title = {Closed-loop platoon simulation with cooperative intelligent transportation systems based on vehicle-to-X communication}, series = {Simulation Modelling Practice and Theory}, volume = {106}, journal = {Simulation Modelling Practice and Theory}, number = {Art. 102173}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1569-190X}, doi = {10.1016/j.simpat.2020.102173}, year = {2021}, language = {en} } @inproceedings{MoehrenBergmannJanseretal.2023, author = {M{\"o}hren, Felix and Bergmann, Ole and Janser, Frank and Braun, Carsten}, title = {On the determination of harmonic propeller loads}, series = {AIAA SCITECH 2023 Forum}, booktitle = {AIAA SCITECH 2023 Forum}, publisher = {AIAA}, doi = {10.2514/6.2023-2404}, pages = {12 Seiten}, year = {2023}, abstract = {Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures.}, language = {en} } @article{NeuJanserKhatibietal.2016, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Braun, Carsten and Orifici, Adrian C.}, title = {Operational Modal Analysis of a wing excited by transonic flow}, series = {Aerospace Science and Technology}, volume = {49}, journal = {Aerospace Science and Technology}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1270-9638}, doi = {10.1016/j.ast.2015.11.032}, pages = {73 -- 79}, year = {2016}, abstract = {Operational Modal Analysis (OMA) is a promising candidate for flutter testing and Structural Health Monitoring (SHM) of aircraft wings that are passively excited by wind loads. However, no studies have been published where OMA is tested in transonic flows, which is the dominant condition for large civil aircraft and is characterized by complex and unique aerodynamic phenomena. We use data from the HIRENASD large-scale wind tunnel experiment to automatically extract modal parameters from an ambiently excited wing operated in the transonic regime using two OMA methods: Stochastic Subspace Identification (SSI) and Frequency Domain Decomposition (FDD). The system response is evaluated based on accelerometer measurements. The excitation is investigated from surface pressure measurements. The forcing function is shown to be non-white, non-stationary and contaminated by narrow-banded transonic disturbances. All these properties violate fundamental OMA assumptions about the forcing function. Despite this, all physical modes in the investigated frequency range were successfully identified, and in addition transonic pressure waves were identified as physical modes as well. The SSI method showed superior identification capabilities for the investigated case. The investigation shows that complex transonic flows can interfere with OMA. This can make existing approaches for modal tracking unsuitable for their application to aircraft wings operated in the transonic flight regime. Approaches to separate the true physical modes from the transonic disturbances are discussed.}, language = {en} } @inproceedings{NeuJanserKhatibietal.2015, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.}, title = {Operational modal analysis of a cantilever in a wind tunnel using optical fiber bragg grating sensors}, series = {6th International Operational Modal Analysis Conference. IOMAC´15. 2015 May 12-14 Gijon - Spain}, booktitle = {6th International Operational Modal Analysis Conference. IOMAC´15. 2015 May 12-14 Gijon - Spain}, doi = {10.13140/RG.2.1.3753.0324}, pages = {10 S.}, year = {2015}, language = {en} } @article{NeuJanserKhatibietal.2017, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.}, title = {Fully Automated Operational Modal Analysis using multi-stage clustering}, series = {Mechanical Systems and Signal Processing}, volume = {Vol. 84, Part A}, journal = {Mechanical Systems and Signal Processing}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0888-3270}, doi = {10.1016/j.ymssp.2016.07.031}, pages = {308 -- 323}, year = {2017}, language = {en} } @article{NeuJanserKhatibietal.2016, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.}, title = {Automated modal parameter-based anomaly detection under varying wind excitation}, series = {Structural Health Monitoring}, volume = {15}, journal = {Structural Health Monitoring}, number = {6}, publisher = {Sage}, address = {London}, issn = {1475-9217}, doi = {10.1177/1475921716665803}, pages = {1 -- 20}, year = {2016}, abstract = {Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions.}, language = {en} } @inproceedings{NeuJanserKhatibietal.2016, author = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.}, title = {In-flight vibration-based structural health monitoring of aircraft wings}, series = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea}, booktitle = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea}, pages = {10 Seiten}, year = {2016}, abstract = {This work presents a methodology for automated damage-sensitive feature extraction and anomaly detection under multivariate operational variability for in-flight assessment of wings. The method uses a passive excitation approach, i. e. without the need for artificial actuation. The modal system properties (natural frequencies and damping ratios) are used as damage-sensitive features. Special emphasis is placed on the use of Fiber Bragg Grating (FBG) sensing technology and the consideration of Operational and Environmental Variability (OEV). Measurements from a wind tunnel investigation with a composite cantilever equipped with FBG and piezoelectric sensors are used to successfully detect an impact damage. In addition, the feasibility of damage localisation and severity estimation is evaluated based on the coupling found between damageand OEV-induced feature changes.}, language = {en} } @inproceedings{NiedermeierClemensKowalskietal.2014, author = {Niedermeier, H. and Clemens, J. and Kowalski, Julia and Macht, S. and Heinen, D. and Hoffmann, R. and Linder, Peter}, title = {Navigation system for a research ice probe for antarctic glaciers}, series = {IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif.}, booktitle = {IEEE/ION Position, Location and Navigation Symposium (PLANS) ; 5-8 May 2014, Monterey, Calif.}, publisher = {IEEE}, address = {Piscataway, NJ}, organization = {Position, Location and Navigation Symposium <2014, Monterey, Calif.>}, isbn = {978-1-4799-3319-8}, pages = {959 -- 975}, year = {2014}, language = {en} } @misc{NonhoffWahle1990, author = {Nonhoff, Gottfried and Wahle, Michael}, title = {Anordnung zur D{\"a}mpfung von Schwingungen an Bauwerken und Bauteilen : Offenlegungsschrift / Europ{\"a}ische Patentschrift}, publisher = {Deutsches Patent- und Markenamt / Europ{\"a}isches Patentamt}, address = {M{\"u}nchen / Den Hague}, pages = {7 S. : graph. Darst.}, year = {1990}, language = {de} } @inproceedings{NowackRoethBuehrigPolaczeketal.2008, author = {Nowack, N. and R{\"o}th, Thilo and B{\"u}hrig-Polaczek, A. and Klaus, G.}, title = {Advanced Sheet Metal Components Reinforced by Light Metal Cast Structures}, series = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]}, booktitle = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]}, number = {2}, editor = {Hirsch, J{\"u}rgen}, isbn = {978-3-527-32367-8}, pages = {2374 -- 2381}, year = {2008}, language = {en} } @inproceedings{OhndorfDachwaldSeboldtetal.2011, author = {Ohndorf, Andreas and Dachwald, Bernd and Seboldt, Wolfgang and Schartner, Karl-Heinz}, title = {Flight times to the heliopause using a combination of solar and radioisotope electric propulsion}, series = {32nd International Electric Propulsion Conference}, booktitle = {32nd International Electric Propulsion Conference}, pages = {1 -- 12}, year = {2011}, abstract = {We investigate the interplanetary flight of a low-thrust space probe to the heliopause,located at a distance of about 200 AU from the Sun. Our goal was to reach this distance within the 25 years postulated by ESA for such a mission (which is less ambitious than the 15-year goal set by NASA). Contrary to solar sail concepts and combinations of allistic and electrically propelled flight legs, we have investigated whether the set flight time limit could also be kept with a combination of solar-electric propulsion and a second, RTG-powered upper stage. The used ion engine type was the RIT-22 for the first stage and the RIT-10 for the second stage. Trajectory optimization was carried out with the low-thrust optimization program InTrance, which implements the method of Evolutionary Neurocontrol,using Artificial Neural Networks for spacecraft steering and Evolutionary Algorithms to optimize the Neural Networks' parameter set. Based on a parameter space study, in which the number of thrust units, the unit's specific impulse, and the relative size of the solar power generator were varied, we have chosen one configuration as reference. The transfer time of this reference configuration was 29.6 years and the fastest one, which is technically more challenging, still required 28.3 years. As all flight times of this parameter study were longer than 25 years, we further shortened the transfer time by applying a launcher-provided hyperbolic excess energy up to 49 km2/s2. The resulting minimal flight time for the reference configuration was then 27.8 years. The following, more precise optimization to a launch with the European Ariane 5 ECA rocket reduced the transfer time to 27.5 years. This is the fastest mission design of our study that is flexible enough to allow a launch every year. The inclusion of a fly-by at Jupiter finally resulted in a flight time of 23.8 years,which is below the set transfer-time limit. However, compared to the 27.5-year transfer,this mission design has a significantly reduced launch window and mission flexibility if the escape direction is restricted to the heliosphere's "nose".}, language = {en} } @article{OlaruKowalskiSethietal.2012, author = {Olaru, Alexandra Maria and Kowalski, Julia and Sethi, Vaishali and Bl{\"u}mich, Bernhard}, title = {Exchange relaxometry of flow at small P{\´e}clet numbers in a glass bead pack}, series = {Journal of Magnetic Resonance (JMR)}, volume = {220}, journal = {Journal of Magnetic Resonance (JMR)}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1096-0856}, doi = {10.1016/j.jmr.2012.04.015}, pages = {32 -- 44}, year = {2012}, abstract = {In this paper we consider low P{\´e}clet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.}, language = {en} } @inproceedings{OlaruKowalskiSethietal.2011, author = {Olaru, Alexandra Maria and Kowalski, Julia and Sethi, Vaishali and Bl{\"u}mich, Bernhard}, title = {Fluid Transport in Porous Media probed by Relaxation-Exchange NMR}, series = {2011 Fall Meeting, AGU, San Francisco, Calif., 5-9 Dec.}, booktitle = {2011 Fall Meeting, AGU, San Francisco, Calif., 5-9 Dec.}, year = {2011}, language = {en} } @inproceedings{OttenSchmidWeber2015, author = {Otten, D. and Schmid, M. and Weber, Tobias}, title = {Advances In Sheet Metal-Forming: Reduction Of Tooling Cost By Methodical Optimization}, series = {Proceedings of SAMPE Europe Conference, Amiens , France}, booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France}, year = {2015}, language = {en} } @inproceedings{OttenSchmidtWeber2016, author = {Otten, D. and Schmidt, M. and Weber, Tobias}, title = {Advances in Determination of Material Parameters for Functional Simulations Based on Process Simulations}, series = {SAMPE Europe Conference 16 Liege}, booktitle = {SAMPE Europe Conference 16 Liege}, isbn = {978-1-5108-3800-0}, pages = {570 -- 577}, year = {2016}, language = {en} } @article{OttenWeberArent2018, author = {Otten, Dennis and Weber, Tobias and Arent, Jan-Christoph}, title = {Manufacturing Process Simulation - On Its Way to Industrial Application}, series = {International Journal of Aviation, Aeronautics, and Aerospace}, volume = {5}, journal = {International Journal of Aviation, Aeronautics, and Aerospace}, number = {2}, publisher = {Embry-Riddle Aeronautical University}, address = {Daytona Beach, Fla.}, issn = {2374-6793}, doi = {10.15394/ijaaa.2018.1217}, year = {2018}, abstract = {Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview of the capabilities of MPS in the fields of sheet metal forming and prepreg autoclave manufacturing of composite parts summarizing the resulting benefits for tooling design and manufacturing engineering. The simulation technology is explained briefly in order to show several simplification and optimization techniques for developing industrialized simulation approaches. Small case studies provide examples of an efficient application on an industrial scale.}, language = {en} } @article{OverduinBlomeHoell2007, author = {Overduin, James and Blome, Hans-Joachim and Hoell, Josef}, title = {Wolfgang Priester: from the big bounce to the Lambda-dominated universe}, series = {Naturwissenschaften}, volume = {94}, journal = {Naturwissenschaften}, number = {6}, isbn = {0028-1042}, pages = {417 -- 429}, year = {2007}, language = {en} } @inproceedings{PaslighFunkeRoethetal.2010, author = {Pasligh, N. and Funke, D. and R{\"o}th, Thilo and Krack, R.}, title = {Leichtbau Quertrager als Stahlblech-Aluminiumdruckguss-Hybrid - Von der numerischen Berechnung bis zum realen Prototypen}, series = {VDI BERICHTE}, booktitle = {VDI BERICHTE}, publisher = {VDI Verlag}, address = {D{\"u}sseldorf}, isbn = {978-3-18-092107-5}, pages = {688 Seiten}, year = {2010}, language = {de} } @article{PeekenRosenkranzSchelenz1991, author = {Peeken, Heinz and Rosenkranz, Josef and Schelenz, R.}, title = {Ber{\"u}cksichtigung des Einflusses der Gleitlagergeh{\"a}usesteifigkeit auf das dynamische Verhalten von Rotoren}, series = {Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.}, volume = {30}, journal = {Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.}, number = {9}, issn = {0341-2652}, pages = {71 -- 75}, year = {1991}, language = {de} } @inproceedings{PeekenTroederSchmidtetal.1985, author = {Peeken, Heinz and Troeder, Christoph and Schmidt, J. and Rosenkranz, Josef}, title = {Principles of machine noise reduction}, series = {Inter-noise 85 : proceedings ; 1985 international conference on noise control engineering ; Munich, Sept. 18 - 20, 1985. - (Schriftenreihe der Bundesanstalt f{\"u}r Arbeitsschutz : Tagungsbericht ; 39)}, booktitle = {Inter-noise 85 : proceedings ; 1985 international conference on noise control engineering ; Munich, Sept. 18 - 20, 1985. - (Schriftenreihe der Bundesanstalt f{\"u}r Arbeitsschutz : Tagungsbericht ; 39)}, publisher = {Bundesanstalt f{\"u}r Arbeitsschutz [u.a.]}, address = {Dortmund [u.a.]}, isbn = {3-88314-417-7}, pages = {23 -- 36}, year = {1985}, language = {en} } @inproceedings{PeloniCeriottiDachwald2015, author = {Peloni, A. and Ceriotti, M. and Dachwald, Bernd}, title = {Preliminary trajectory design of a multiple NEO rendezvous mission through solar sailing}, series = {Proceedings of the International Astronautical Congress, IAC, Vol. 8, 2014}, booktitle = {Proceedings of the International Astronautical Congress, IAC, Vol. 8, 2014}, publisher = {Curran}, address = {Red Hook, NY}, isbn = {978-1-63439-986-9}, pages = {5352 -- 5366}, year = {2015}, language = {en} } @inproceedings{PeloniCeriottiDachwald2015, author = {Peloni, Alessandro and Ceriotti, Matteo and Dachwald, Bernd}, title = {Solar-Sailing Trajectory Design for Close-up NEA Observations Mission}, series = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy}, booktitle = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy}, pages = {21 S.}, year = {2015}, language = {de} } @article{PeloniCeriottiDachwald2016, author = {Peloni, Alessandro and Ceriotti, Matteo and Dachwald, Bernd}, title = {Solar-sail trajectory design for a multiple near-earth-asteroid rendezvous mission}, series = {Journal of Guidance, Control, and Dynamics}, volume = {39}, journal = {Journal of Guidance, Control, and Dynamics}, number = {12}, publisher = {AIAA}, address = {Reston, Va.}, issn = {0731-5090}, doi = {10.2514/1.G000470}, pages = {2712 -- 2724}, year = {2016}, abstract = {The scientific interest for near-Earth asteroids as well as the interest in potentially hazardous asteroids from the perspective of planetary defense led the space community to focus on near-Earth asteroid mission studies. A multiple near-Earth asteroid rendezvous mission with close-up observations of several objects can help to improve the characterization of these asteroids. This work explores the design of a solar-sail spacecraft for such a mission, focusing on the search of possible sequences of encounters and the trajectory optimization. This is done in two sequential steps: a sequence search by means of a simplified trajectory model and a set of heuristic rules based on astrodynamics, and a subsequent optimization phase. A shape-based approach for solar sailing has been developed and is used for the first phase. The effectiveness of the proposed approach is demonstrated through a fully optimized multiple near-Earth asteroid rendezvous mission. The results show that it is possible to visit five near-Earth asteroids within 10 years with near-term solar-sail technology.}, language = {en} } @article{PeloniDachwaldCeriotti2017, author = {Peloni, Alessandro and Dachwald, Bernd and Ceriotti, Matteo}, title = {Multiple near-earth asteroid rendezvous mission: Solar-sailing options}, series = {Advances in Space Research}, journal = {Advances in Space Research}, number = {In Press, Corrected Proof}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0273-1177}, doi = {10.1016/j.asr.2017.10.017}, year = {2017}, language = {en} } @inproceedings{PeloniDachwaldCeriotti2017, author = {Peloni, Alessandro and Dachwald, Bernd and Ceriotti, Matteo}, title = {Multiple NEA rendezvous mission: Solar sailing options}, series = {Fourth International Symposium on Solar Sailing}, booktitle = {Fourth International Symposium on Solar Sailing}, pages = {1 -- 11}, year = {2017}, abstract = {The scientific interest in near-Earth asteroids (NEAs) and the classification of some of those as potentially hazardous asteroid for the Earth stipulated the interest in NEA exploration. Close-up observations of these objects will increase drastically our knowledge about the overall NEA population. For this reason, a multiple NEA rendezvous mission through solar sailing is investigated, taking advantage of the propellantless nature of this groundbreaking propulsion technology. Considering a spacecraft based on the DLR/ESA Gossamer technology, this work focuses on the search of possible sequences of NEA encounters. The effectiveness of this approach is demonstrated through a number of fully-optimized trajectories. The results show that it is possible to visit five NEAs within 10 years with near-term solar-sail technology. Moreover, a study on a reduced NEA database demonstrates the reliability of the approach used, showing that 58\% of the sequences found with an approximated trajectory model can be converted into real solar-sail trajectories. Lastly, this second study shows the effectiveness of the proposed automatic optimization algorithm, which is able to find solutions for a large number of mission scenarios without any input required from the user.}, language = {en} } @article{PetersonRoethUibel2017, author = {Peterson, Leif Arne and R{\"o}th, Thilo and Uibel, Thomas}, title = {Einsatz von Holzwerkstoffen in Fahrzeugstrukturen}, series = {Bauen mit Holz}, journal = {Bauen mit Holz}, number = {3}, publisher = {Bruderverlag}, address = {K{\"o}ln}, issn = {0005-6545}, pages = {32 -- 38}, year = {2017}, language = {de} }