@article{KilicRaatschenKoerfgenetal.2017,
  author    = {Kilic, S. A. and Raatschen, Hans-J{\"u}rgen and K{\"o}rfgen, B. and Apaydin, N. M. and Astaneh-Asl, A.},
  title     = {FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements},
  series = {Arabian Journal for Science and Engineering},
  volume    = {42},
  journal   = {Arabian Journal for Science and Engineering},
  number    = {3},
  publisher = {Springer Nature},
  issn      = {2191-4281},
  doi       = {10.1007/s13369-016-2316-y},
  pages     = {1103 -- 1116},
  year      = {2017},
  abstract  = {This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 \% of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach.},
  language  = {en}
}
@article{DuesGebhardtKallweitetal.1994,
  author    = {Dues, M. and Gebhardt, Andreas and Kallweit, Stephan and Scheffler, T. and Siekmann, H. and Uchiyama, T.},
  title     = {Flow Visualization in a Cavitating Flow},
  series = {Proceedings of the German-Japanese Symposium on Multi-Phase Flow : Karlsruhe, Germany, August 23 - 25, 1994 / comp. by U. M{\"u}ller ...},
  journal   = {Proceedings of the German-Japanese Symposium on Multi-Phase Flow : Karlsruhe, Germany, August 23 - 25, 1994 / comp. by U. M{\"u}ller ...},
  publisher = {Kernforschungszentrum Karlsruhe},
  address   = {Karlsruhe},
  pages     = {391 -- 402},
  year      = {1994},
  language  = {en}
}
@article{UlmerBraunChengetal.2022,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Gamification of virtual reality assembly training: Effects of a combined point and level system on motivation and training results},
  series = {International Journal of Human-Computer Studies},
  volume    = {165},
  journal   = {International Journal of Human-Computer Studies},
  number    = {Art. No. 102854},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1071-5819},
  doi       = {10.1016/j.ijhcs.2022.102854},
  year      = {2022},
  abstract  = {Virtual Reality (VR) offers novel possibilities for remote training regardless of the availability of the actual equipment, the presence of specialists, and the training locations. Research shows that training environments that adapt to users' preferences and performance can promote more effective learning. However, the observed results can hardly be traced back to specific adaptive measures but the whole new training approach. This study analyzes the effects of a combined point and leveling VR-based gamification system on assembly training targeting specific training outcomes and users' motivations. The Gamified-VR-Group with 26 subjects received the gamified training, and the Non-Gamified-VR-Group with 27 subjects received the alternative without gamified elements. Both groups conducted their VR training at least three times before assembling the actual structure. The study found that a level system that gradually increases the difficulty and error probability in VR can significantly lower real-world error rates, self-corrections, and support usages. According to our study, a high error occurrence at the highest training level reduced the Gamified-VR-Group's feeling of competence compared to the Non-Gamified-VR-Group, but at the same time also led to lower error probabilities in real-life. It is concluded that a level system with a variable task difficulty should be combined with carefully balanced positive and negative feedback messages. This way, better learning results, and an improved self-evaluation can be achieved while not causing significant impacts on the participants' feeling of competence.},
  language  = {en}
}
@article{Gebhardt2006,
  author    = {Gebhardt, Andreas},
  title     = {Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping"},
  year      = {2006},
  abstract  = {Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering - Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision},
  subject      = {Rapid prototyping},
  language  = {en}
}
@article{HanrathPlesken1985,
  author    = {Hanrath, Wilhelm and Plesken, Wilhelm},
  title     = {Group rings and irreducible representations of space groups / by W. Hanrath and W. Plesken},
  series = {Journal f{\"u}r die reine und angewandte Mathematik. 362 (1985)},
  journal   = {Journal f{\"u}r die reine und angewandte Mathematik. 362 (1985)},
  isbn      = {0075-4102},
  pages     = {130 -- 140},
  year      = {1985},
  language  = {en}
}
@article{UlmerBraunChengetal.2020,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Human-Centered Gamification Framework for Manufacturing Systems},
  series = {Procedia CIRP},
  volume    = {93},
  journal   = {Procedia CIRP},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  doi       = {10.1016/j.procir.2020.04.076},
  pages     = {670 -- 675},
  year      = {2020},
  abstract  = {While bringing new opportunities, the Industry 4.0 movement also imposes new challenges to the manufacturing industry and all its stakeholders. In this competitive environment, a skilled and engaged workforce is a key to success. Gamification can generate valuable feedbacks for improving employees' engagement and performance. Currently, Gamification in workspaces focuses on computer-based assignments and training, while tasks that require manual labor are rarely considered. This research provides an overview of Enterprise Gamification approaches and evaluates the challenges. Based on that, a skill-based Gamification framework for manual tasks is proposed, and a case study in the Industry 4.0 model factory is shown.},
  language  = {en}
}
@article{KallweitHelbingOrglmeisteretal.1994,
  author    = {Kallweit, Stephan and Helbing, M. and Orglmeister, R. and Siekmann, H. E.},
  title     = {Image Processing Techniques with Neural Networks for Flow Visualization in Rotating Machinery / Helbing, M. ; Orgimeiste, R. [Orglmeister, R.] ; Kallweit, S. ; Siekmann, H. E. ; Dues, M. ; Cronemeyer, J.},
  series = {FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Lab{\`e}ge / CERT/ONERA. General chairman Patrick Hebrard},
  journal   = {FLUCOME '94 : the 4th Triennial International Symposium on Fluid Control, Measurement and Visualization; August 29 - September 1, 1994, Toulouse, France, International Congress Centre, DIGORA-Lab{\`e}ge / CERT/ONERA. General chairman Patrick Hebrard},
  address   = {Toulouse},
  pages     = {87 -- 94},
  year      = {1994},
  language  = {en}
}
@article{CosmaKesslerGebhardtetal.2020,
  author    = {Cosma, Cosmin and Kessler, Julia and Gebhardt, Andreas and Campbell, Ian and Balc, Nicolae},
  title     = {Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed},
  series = {Materials},
  volume    = {13},
  journal   = {Materials},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1944},
  doi       = {10.3390/ma13040905},
  pages     = {1 -- 18},
  year      = {2020},
  abstract  = {To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10\% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250-1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20\% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L.},
  language  = {en}
}
@article{RoesnerScheikOlowinskyetal.2011,
  author    = {Roesner, Andreas and Scheik, Sven and Olowinsky, Alexander and Gillner, Arnold and Propawe, Reinhart and Schleser, Markus and Reisgen, Uwe},
  title     = {Innovative approach of joining hybrid components},
  series = {Journal of laser applications},
  volume    = {Vol. 23},
  journal   = {Journal of laser applications},
  number    = {Iss. 3},
  publisher = {Laser Institute of America},
  address   = {Orlando, Fla.},
  issn      = {1042-346X},
  pages     = {32007},
  year      = {2011},
  language  = {en}
}
@article{GlowaniaGriesSchoeneetal.2011,
  author    = {Glowania, Michael and Gries, Thomas and Schoene, Jens and Schleser, Markus and Reisgen, Uwe},
  title     = {Innovative coating technology for textile reinforcements of concrete applications},
  series = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)},
  journal   = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)},
  publisher = {Trans Tech Publications},
  address   = {B{\"a}ch},
  organization    = {International Congress Polymers in Concrete <13, 2010, Funchal, Madeira>},
  isbn      = {978-3-03785-008-4},
  issn      = {1013-9826 (E-Journal) ; 0252-1059 (Print)},
  pages     = {167 -- 173},
  year      = {2011},
  language  = {en}
}
@article{DiltheySchleserFeldmannetal.2008,
  author    = {Dilthey, Ulrich and Schleser, Markus and Feldmann, Martin and Pak, Daniel and Geßler, Achim},
  title     = {Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts},
  series = {Cement and concrete composites},
  volume    = {Vol. 30},
  journal   = {Cement and concrete composites},
  number    = {iss. 2},
  issn      = {0958-9465},
  pages     = {82 -- 87},
  year      = {2008},
  language  = {en}
}
@article{AnikFrohberg1983,
  author    = {Anik, Sabri and Frohberg, Martin G.},
  title     = {Investigation of the thermodynamics of oxygen and the determination of phase boundaries in the system copper-oxygen-bismuth at 12000C},
  series = {Zeitschrift f{\"u}r Metallkunde},
  volume    = {74},
  journal   = {Zeitschrift f{\"u}r Metallkunde},
  number    = {8},
  issn      = {0044-3093},
  pages     = {530 -- 534},
  year      = {1983},
  language  = {en}
}
@article{AnikFrohberg1984,
  author    = {Anik, Sabri and Frohberg, Martin G.},
  title     = {Investigations of the thermodynamics of oxygen and the determination of the miscibility gap in the system copper-oxygen-lead at 12000C},
  series = {Zeitschrift f{\"u}r Metallkunde},
  volume    = {75},
  journal   = {Zeitschrift f{\"u}r Metallkunde},
  number    = {8},
  issn      = {0044-3093},
  pages     = {586 -- 589},
  year      = {1984},
  language  = {en}
}
@article{RoesnerScheikOlowinskyetal.2011,
  author    = {Roesner, Andreas and Scheik, Sven and Olowinsky, Alexander and Gillner, Arnold and Reisgen, Uwe and Schleser, Markus},
  title     = {Laser assisted joining of plastic metal hybrids},
  series = {Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B)},
  journal   = {Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  organization    = {International WLT Conference on Lasers in Manufacturing <6, M{\"u}nchen, 2011>},
  issn      = {1875-3892 (E-Journal); 1875-3884 (Print)},
  pages     = {370 -- 377},
  year      = {2011},
  language  = {en}
}
@article{ReisgenOlschokJakobsetal.2012,
  author    = {Reisgen, Uwe and Olschok, Simon and Jakobs, Stefan and Schleser, Markus and Mokrov, Oleg and Rossiter, Eduardo},
  title     = {Laser beam submerged arc hybrid welding},
  series = {Physics procedia},
  volume    = {39},
  journal   = {Physics procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892},
  doi       = {10.1016/j.phpro.2012.10.016},
  pages     = {75 -- 83},
  year      = {2012},
  abstract  = {The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.},
  language  = {en}
}
@article{Gebhardt2001,
  author    = {Gebhardt, Andreas},
  title     = {Laserwelding with fillerwire},
  series = {LIA handbook of laser material processing / Laser Institute of America},
  journal   = {LIA handbook of laser material processing / Laser Institute of America},
  address   = {Orlando, Florida},
  isbn      = {3-540-41770-2},
  year      = {2001},
  language  = {en}
}
@article{StarkeDrews1994,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Le soudage au siecle de l'informatique},
  series = {Souder. 18 (1994), H. 6},
  journal   = {Souder. 18 (1994), H. 6},
  isbn      = {0246-1900},
  pages     = {33 -- 44},
  year      = {1994},
  language  = {en}
}
@article{KaemperLehrEhrfeldetal.1994,
  author    = {K{\"a}mper, Klaus-Peter and Lehr, H. and Ehrfeld, W. and Michel, F.},
  title     = {LIGA Components for the Construction of Milliactuators. Lehr, H.; Ehrfeld, W.; K{\"a}mper, K.-P.; Michel, F.; Schmidt, M.},
  series = {1994 IEEE Symposium on Emerging Technologies \& Factory Automation : novel disciplines for the next century ; proceedings, November 6 - 10, 1994, Tokyo, Japan / ETFA '94. Hiroyuki Fujita [chairman] ... Sponsored by: Institute of Industrial Science, SEIKEN},
  journal   = {1994 IEEE Symposium on Emerging Technologies \& Factory Automation : novel disciplines for the next century ; proceedings, November 6 - 10, 1994, Tokyo, Japan / ETFA '94. Hiroyuki Fujita [chairman] ... Sponsored by: Institute of Industrial Science, SEIKEN},
  address   = {Piscataway, N.J.},
  isbn      = {0780321146},
  pages     = {43 -- 47},
  year      = {1994},
  language  = {en}
}
@article{KaemperHagemannLehretal.1995,
  author    = {K{\"a}mper, Klaus-Peter and Hagemann, B. and Lehr, H. and Michel, F.},
  title     = {LIGA Example 2: Electromagnetic Micromotor. Hagemann, B.; K{\"a}mper, K.-P.; Lehr, H.; Michel, F.; Th{\"u}rigen, C.},
  series = {LIGA technique / Hans-Dieter Bauer (ed.). [Developed by UETP-MEMS, University Training Partnership for Micro-Electro-Mechanical Systems ...]. - 2.ed.},
  journal   = {LIGA technique / Hans-Dieter Bauer (ed.). [Developed by UETP-MEMS, University Training Partnership for Micro-Electro-Mechanical Systems ...]. - 2.ed.},
  publisher = {FSRM},
  address   = {Neuchatel},
  pages     = {100 -- 110},
  year      = {1995},
  language  = {en}
}
@article{KaemperSchulzEhrfeldetal.1994,
  author    = {K{\"a}mper, Klaus-Peter and Schulz, C. and Ehrfeld, W. and Erbel, R.},
  title     = {LIGA Fabricated Microsystems for Medical and Related Applications. Schulz, C.; Ehrfeld, W.; Erbel, R.; K{\"a}mper, K.-P.; Koch, L.; Lehr, H.; Roth, T.},
  series = {3-Day Course on Microengineering in Medicine and Biology and its Applications to Minimally Invasive Techniques for Therapy and Medical Diagnosis : EURO-BME 94; October 5, 6, and 7, 1994, Swiss Federal Institute of Technology, EPFL, Lausanne, Switzerland / [the 1994 EURO-BME Microengineering in Medicine and Biology Training Course. Staff: Christian D. Depeursinge ...]},
  journal   = {3-Day Course on Microengineering in Medicine and Biology and its Applications to Minimally Invasive Techniques for Therapy and Medical Diagnosis : EURO-BME 94; October 5, 6, and 7, 1994, Swiss Federal Institute of Technology, EPFL, Lausanne, Switzerland / [the 1994 EURO-BME Microengineering in Medicine and Biology Training Course. Staff: Christian D. Depeursinge ...]},
  publisher = {REPRO EPFL},
  address   = {Lausanne},
  pages     = {Getr. Z{\"a}hlung : Ill., graph. Darst.},
  year      = {1994},
  language  = {en}
}
@article{EnningZambouAbel2005,
  author    = {Enning, Manfred and Zambou, N. and Abel, D.},
  title     = {Longitudinal Control of Following Vehicles within Platoon : A Model-Based Predictive Approach / Zambou, N. ; Enning, M. ; Abel, D.},
  series = {Advances in automotive control 2004 : a proceedings volume from the IFAC symposium, Salerno, Italy, 19 - 23 April 2004 / ed. C. Pianese},
  journal   = {Advances in automotive control 2004 : a proceedings volume from the IFAC symposium, Salerno, Italy, 19 - 23 April 2004 / ed. C. Pianese},
  publisher = {Elsevier},
  address   = {Oxford},
  isbn      = {0080442501},
  pages     = {733 -- 738},
  year      = {2005},
  language  = {en}
}
@article{KaemperPappasMilleretal.1991,
  author    = {K{\"a}mper, Klaus-Peter and Pappas, D. P. and Miller, B. P. and Hopster, H.},
  title     = {Magnetism of ultrathin films of Fe on Cu(100). Pappas, D. P; K{\"a}mper, K.-P.; Miller, B. P.; Hopster, H.; Fowler, D. E.; Luntz, A. C.; Brundle, C.R.; Shen, Z.-X.},
  series = {Journal of Applied Physics. 69 (1991), H. 8},
  journal   = {Journal of Applied Physics. 69 (1991), H. 8},
  isbn      = {1089-7550},
  pages     = {5209 -- 521},
  year      = {1991},
  language  = {en}
}
@article{KaemperEhrfeldHesseletal.1997,
  author    = {K{\"a}mper, Klaus-Peter and Ehrfeld, W. and Hessel, V. and Lacher, M.},
  title     = {Market oriented development and production of microdevices. Ehrfeld, W.; Hessel, V.; K{\"a}mper, K.-P.; Lacher, M.; Picard, A.; Schmidt, M.; Schulz, C.},
  series = {Proceedings : 21th International Conference on Microelectronics : MIEL '97 ; Niš, Yugoslavia, 14-17 September 1997. Vol. 1},
  journal   = {Proceedings : 21th International Conference on Microelectronics : MIEL '97 ; Niš, Yugoslavia, 14-17 September 1997. Vol. 1},
  publisher = {IEEE Service Center},
  address   = {Piscataway, NJ},
  isbn      = {0-7803-3664-X},
  pages     = {71 -- 79},
  year      = {1997},
  language  = {en}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrey},
  title     = {Measuring of plasma properties induced by non-vacuum electron beam welding},
  series = {Physics of plasma},
  volume    = {19},
  journal   = {Physics of plasma},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {1089-7674 (E-Journal); 1070-664X (Print)},
  doi       = {10.1063/1.3675874},
  pages     = {1 -- 7},
  year      = {2012},
  abstract  = {Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel's method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.},
  language  = {en}
}
@article{EnningJenayehMuelleretal.1998,
  author    = {Enning, Manfred and Jenayeh, I. and M{\"u}ller, C. and Kositza, N.},
  title     = {Mechatronics in automating shunting processes in marshalling yards / Jenayeh, I. ; M{\"u}ller, C.; Kositza, N. ; Enning, M. ; Rake, H.},
  series = {Mechatronics '98 : proceedings of the 6th UK Mechatronics Forum International Conference, Sk{\"o}vde, Sweden, 9-11 September 1998},
  journal   = {Mechatronics '98 : proceedings of the 6th UK Mechatronics Forum International Conference, Sk{\"o}vde, Sweden, 9-11 September 1998},
  publisher = {Pergamon},
  address   = {Amsterdam},
  isbn      = {0-08-043339-1},
  pages     = {xxi, 918 S. : graph. Darst.},
  year      = {1998},
  language  = {en}
}
@article{KaemperDoepperClemensetal.1997,
  author    = {K{\"a}mper, Klaus-Peter and D{\"o}pper, J. and Clemens, M. and Ehrfeld, W.},
  title     = {Micro gear pumps for dosing of viscous fluids. / D{\"o}pper, J. (u.a.)},
  series = {Journal of Micromechanics and Microengineering. 7 (1997), H. 3},
  journal   = {Journal of Micromechanics and Microengineering. 7 (1997), H. 3},
  isbn      = {0960-1317},
  pages     = {230 -- 232},
  year      = {1997},
  language  = {en}
}
@article{KaemperLehrAbeletal.1996,
  author    = {K{\"a}mper, Klaus-Peter and Lehr, H. and Abel, S. and D{\"o}pper, J.},
  title     = {Microactuators as driving units for microrobotic systems. Herstellung von Mikroaktoren mit dem LIGA-Verfahren f{\"u}r Mikroroboter / Lehr, H.; Abel, S.; D{\"o}pper, J.; Ehrfeld, W.; Hagemann, B.; K{\"a}mper, K.-P.; Michel, F.; Schulu, c.; Th{\"u}rigen, C.},
  series = {Proceedings of the SPIE - The International Society for Optical Engineering},
  journal   = {Proceedings of the SPIE - The International Society for Optical Engineering},
  isbn      = {0277-786X},
  pages     = {202 -- 210},
  year      = {1996},
  language  = {en}
}
@article{KaemperEhrfeldDoepperetal.1997,
  author    = {K{\"a}mper, Klaus-Peter and Ehrfeld, W. and D{\"o}pper, J. and Hessel, V.},
  title     = {Microfluidic components for biological and chemical microreactors. K{\"a}mper, K.-P.; Ehrfeld, W.; D{\"o}pper, J.; Hessel, V.; Lehr, H.; L{\"o}we, H.; Richter, T.; Wolf, A.},
  series = {Proceedings : an investigation of micro structures, sensors, actuators, machines and robots ; Nagoya, Japan, January 26 - 30, 1997 / IEEE Robotics and Automation Society ...},
  journal   = {Proceedings : an investigation of micro structures, sensors, actuators, machines and robots ; Nagoya, Japan, January 26 - 30, 1997 / IEEE Robotics and Automation Society ...},
  publisher = {IEEE Service Center},
  address   = {Piscataway, NJ},
  isbn      = {0-7803-3744-1},
  pages     = {338 -- 343},
  year      = {1997},
  language  = {en}
}
@article{RamazaniLiMukherjeeetal.2013,
  author    = {Ramazani, Ali and Li, Yang and Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Abdurakhmanov, Aydemir and Schleser, Markus and Reisgen, Uwe},
  title     = {Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding},
  series = {Computational materials science},
  volume    = {Vol. 68},
  journal   = {Computational materials science},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-0801 (E-Book); 0927-0256 (Print)},
  pages     = {107 -- 116},
  year      = {2013},
  language  = {en}
}
@article{KaemperAbrahamEhrfeldetal.1998,
  author    = {K{\"a}mper, Klaus-Peter and Abraham, M. and Ehrfeld, W. and Hessel, V.},
  title     = {Microsystem technology: Between research and industrial application. Abraham, M.; Ehrfeld, W.; Hessel, V.; K{\"a}mper, K.-P.; Lacher, M.; Picard, A.},
  series = {Microelectronic Engineering. 41-42 (1998)},
  journal   = {Microelectronic Engineering. 41-42 (1998)},
  isbn      = {0167-9317},
  pages     = {47 -- 52},
  year      = {1998},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modelling and visualisation of the GMA process},
  series = {Welding and Cutting},
  volume    = {11},
  journal   = {Welding and Cutting},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {1612-3433},
  pages     = {242 -- 249},
  year      = {2012},
  language  = {en}
}
@article{SchwarzGebhardtSchleseretal.2019,
  author    = {Schwarz, Alexander and Gebhardt, Andreas and Schleser, Markus and Popoola, Patricia},
  title     = {New Welding Joint Geometries Manufactured by Powder Bed Fusion from 316L},
  series = {Materials Performance and Characterization 8},
  journal   = {Materials Performance and Characterization 8},
  number    = {in press},
  issn      = {2379-1365},
  doi       = {10.1520/MPC20180096},
  year      = {2019},
  language  = {en}
}
@article{EnningZambouAbel2004,
  author    = {Enning, Manfred and Zambou, Nathan and Abel, Dirk},
  title     = {Nonlinear spacing control of following vehicles within platoon a controlled lagrangian approach / Zambou, Nathan ; Enning, Manfred ; Abel, Dirk},
  series = {NOLCOS, IFAC Symposium on Nonlinear Control Systems},
  journal   = {NOLCOS, IFAC Symposium on Nonlinear Control Systems},
  pages     = {1211 -- 1216},
  year      = {2004},
  language  = {en}
}
@article{SeilerPichlerPfaffetal.2009,
  author    = {Seiler, Friedrich and Pichler, Alexander and Pfaff, Raphael and Srulijes, Julio},
  title     = {Novel processing tools for automated doppler picture velocimetry (DPV) evaluation},
  series = {Journal of visualization},
  volume    = {Vol. 12},
  journal   = {Journal of visualization},
  number    = {Iss. 4},
  issn      = {1343-8875},
  pages     = {323 -- 337},
  year      = {2009},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2011,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Numerical and experimental investigation of tensile behavior of laser beam welded TRIP700 steel},
  series = {ISIJ international},
  volume    = {Vol. 51},
  journal   = {ISIJ international},
  number    = {No. 3},
  publisher = {ISIJ},
  address   = {Tōkyō},
  organization    = {Iron and Steel Institute of Japan (ISIJ)},
  issn      = {1347-5460 (E-Journal); 0915-1559 (Print)},
  pages     = {429 -- 434},
  year      = {2011},
  language  = {en}
}
@article{EngemannDuKallweitetal.2020,
  author    = {Engemann, Heiko and Du, Shengzhi and Kallweit, Stephan and C{\"o}nen, Patrick and Dawar, Harshal},
  title     = {OMNIVIL - an autonomous mobile manipulator for flexible production},
  series = {Sensors},
  volume    = {20},
  journal   = {Sensors},
  number    = {24, art. no. 7249},
  publisher = {MDPI},
  address   = {Basel},
  isbn      = {1424-8220},
  doi       = {10.3390/s20247249},
  pages     = {1 -- 30},
  year      = {2020},
  language  = {en}
}
@article{PfaffBurnham2009,
  author    = {Pfaff, Raphael and Burnham, Keith J.},
  title     = {On abstraction and interpretability: a behavioural perspective},
  series = {Systems Science},
  volume    = {Vol. 35},
  journal   = {Systems Science},
  number    = {Iss. 2},
  issn      = {0137-1223},
  pages     = {19 -- 26},
  year      = {2009},
  language  = {en}
}
@article{AhmedReisgenSchleseretal.2010,
  author    = {Ahmed, Essam and Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg},
  title     = {On formability of tailor laser welded blanks of DP/TRIP steel sheets},
  series = {Science and technology of welding and joining},
  volume    = {15},
  journal   = {Science and technology of welding and joining},
  number    = {5},
  publisher = {Maney},
  address   = {Leeds},
  issn      = {1743-2936},
  doi       = {10.1179/136217110X12731414739754},
  pages     = {337 -- 342},
  year      = {2010},
  abstract  = {This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Optimization of laser welding of DP/TRIP steel sheets using statistical approach},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.06.028},
  pages     = {255 -- 262},
  year      = {2012},
  abstract  = {Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box-Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions.},
  language  = {en}
}
@article{KallweitDuesSiekmann1994,
  author    = {Kallweit, Stephan and Dues, M. and Siekmann, H.},
  title     = {Particle-Image-Velocimetry (PIV) in rotierenden Maschinen / Dues, M. ; Kallweit, S. ; Siekmann, H.},
  series = {Lasermethoden in der Str{\"o}mungsmesstechnik, 3. Fachtagung der Deutschen Gesellschaft f{\"u}r Laser-Anemometrie (GALA), Bremen, DE, 5.-7. Sep, 1994},
  journal   = {Lasermethoden in der Str{\"o}mungsmesstechnik, 3. Fachtagung der Deutschen Gesellschaft f{\"u}r Laser-Anemometrie (GALA), Bremen, DE, 5.-7. Sep, 1994},
  publisher = {Shaker},
  address   = {Aachen},
  isbn      = {3-8265-0162-4},
  pages     = {19.1 -- 19-5},
  year      = {1994},
  language  = {en}
}
@article{BeckenbachScheidweiler2016,
  author    = {Beckenbach, Isabel and Scheidweiler, Robert},
  title     = {Perfect ƒ-Matchings and ƒ-Factors in Hypergraphs - A Combinatorial Approach},
  series = {Discrete Mathematics},
  volume    = {240},
  journal   = {Discrete Mathematics},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2192-7782},
  doi       = {10.1016/j.disc.2017.05.005},
  pages     = {2499 -- 2506},
  year      = {2016},
  abstract  = {We prove characterizations of the existence of perfect ƒ-matchings in uniform mengerian and perfect hypergraphs. Moreover, we investigate the ƒ-factor problem in balanced hypergraphs. For uniform balanced hypergraphs we prove two existence theorems with purely combinatorial arguments, whereas for non-uniform balanced hypergraphs we show that the ƒ-factor problem is NP-hard.},
  language  = {en}
}
@article{BraunChengDoweyetal.2021,
  author    = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {Performance evaluation of skill-based order-assignment in production environments with multi-agent systems},
  series = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics},
  journal   = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics},
  number    = {Early Access},
  publisher = {IEEE},
  address   = {New York},
  issn      = {2687-9735},
  doi       = {10.1109/JESTIE.2021.3108524},
  year      = {2021},
  abstract  = {The fourth industrial revolution introduces disruptive technologies to production environments. One of these technologies are multi-agent systems (MASs), where agents virtualize machines. However, the agent's actual performances in production environments can hardly be estimated as most research has been focusing on isolated projects and specific scenarios. We address this gap by implementing a highly connected and configurable reference model with quantifiable key performance indicators (KPIs) for production scheduling and routing in single-piece workflows. Furthermore, we propose an algorithm to optimize the search of extrema in highly connected distributed systems. The benefits, limits, and drawbacks of MASs and their performances are evaluated extensively by event-based simulations against the introduced model, which acts as a benchmark. Even though the performance of the proposed MAS is, on average, slightly lower than the reference system, the increased flexibility allows it to find new solutions and deliver improved factory-planning outcomes. Our MAS shows an emerging behavior by using flexible production techniques to correct errors and compensate for bottlenecks. This increased flexibility offers substantial improvement potential. The general model in this paper allows the transfer of the results to estimate real systems or other models.},
  language  = {en}
}
@article{KallweitSchimpf2003,
  author    = {Kallweit, Stephan and Schimpf, Axel},
  title     = {Photogrammetric Particle Image Velocimetry / Schimpf, Axel ; Kallweit, Stephan},
  series = {Particle image velocimetry : recent improvements; proceedings of the Europiv 2 Workshop held in Zaragoza, Spain, March 31 - April 1, 2003 / edited by M. Stanislas ...},
  journal   = {Particle image velocimetry : recent improvements; proceedings of the Europiv 2 Workshop held in Zaragoza, Spain, March 31 - April 1, 2003 / edited by M. Stanislas ...},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {3-540-21423-2},
  pages     = {295},
  year      = {2003},
  language  = {en}
}
@article{KallweitWillertDuesetal.2008,
  author    = {Kallweit, Stephan and Willert, Chris and Dues, Michael and M{\"u}ller, Ulrich},
  title     = {PIV for Volume Flow Metering / Kallweit, Stephan ; Willert, Chris ; Dues, Michael ; M{\"u}ller, Ulrich ; Lederer, Thomas},
  pages     = {6 S.},
  year      = {2008},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2008,
  author    = {Kallweit, Stephan and Kaminsky, Radoslav and Rossi, Massimiliano and Morbiducci, Umberto},
  title     = {PIV Measurements of Flows in Artificial Heart Valves / Kaminsky, Radoslav ; Kallweit, Stephan ; Rossi, Massimiliano ; Morbiducci, Umberto ; Scalise, Lorenzo},
  series = {Particle Image Velocimetry - New Developments and Recent Applications},
  journal   = {Particle Image Velocimetry - New Developments and Recent Applications},
  isbn      = {978-3-540-73528-1},
  pages     = {55 -- 72},
  year      = {2008},
  language  = {en}
}
@article{KallweitKaminskyRossietal.2005,
  author    = {Kallweit, Stephan and Kaminsky, R. and Rossi, M. and Scalise, L.},
  title     = {PIV Measurements with high temporal Resolution behind Artificial Heart Valves / Kaminsky, R. ; Rossi, M. ; Scalise, L. ; Kallweit, S. ; Verdonck, P.},
  series = {Proceedings of the 6th International Symposium on Particle Image Velocimetry},
  journal   = {Proceedings of the 6th International Symposium on Particle Image Velocimetry},
  publisher = {Caltech},
  address   = {Pasadena, CA},
  year      = {2005},
  language  = {en}
}
@article{GebhardtSchmidt2002,
  author    = {Gebhardt, Andreas and Schmidt, Frank-Michael},
  title     = {Practical experiences with making and finishing of coloured models using 3D printing},
  year      = {2002},
  language  = {en}
}
@article{AnikFrohbergKapoor1983,
  author    = {Anik, Sabri and Frohberg, Martin G. and Kapoor, Madan Lal},
  title     = {Prediction of thermodynamic properties of oxygen in binary metallic solvents},
  series = {Zeitschrift f{\"u}r Metallkunde},
  volume    = {74},
  journal   = {Zeitschrift f{\"u}r Metallkunde},
  number    = {6},
  issn      = {0044-3093},
  pages     = {372 -- 375},
  year      = {1983},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Process Parameters Development of Selective Laser Melting of Lunar Regolith for On-Site Manufacturing Applications},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  isbn      = {1744-7402},
  doi       = {10.1111/ijac.12326},
  pages     = {46 -- 52},
  year      = {2015},
  language  = {en}
}
@article{RaffeisAdjeiKyeremehVroomenetal.2020,
  author    = {Raffeis, Iris and Adjei-Kyeremeh, Frank and Vroomen, Uwe and Westhoff, Elmar and Bremen, Sebastian and Hohoi, Alexandru and B{\"u}hrig-Polaczek, Andreas},
  title     = {Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties},
  series = {Applied Sciences},
  volume    = {10},
  journal   = {Applied Sciences},
  number    = {Art. 3401},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app10103401},
  pages     = {1 -- 15},
  year      = {2020},
  abstract  = {As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni-Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8\% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s-1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20\% to 31\% (V), as well as from 16\% to 25\% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.},
  language  = {en}
}