@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {5},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035897},
  year      = {2020},
  abstract  = {Until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial hybrid-electric, parallel hybrid-electric, fully electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This Paper provides insight into some factors that drive a new design toward either conventional or hybrid propulsion systems. General aviation aircraft, regional transport aircraft vertical takeoff and landing air taxis, and unmanned aerial vehicles are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their takeoff mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Only parallel-hybrid-electric powertrains are taken into account. Aeropropulsive interaction effects are neglected. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints. However, if the propulsion system is sized by a continuous power requirement, hybrid-electric systems offer hardly any benefit.},
  language  = {en}
}
@inproceedings{LudowicyRingsFingeretal.2018,
  author    = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten},
  title     = {Sizing Studies of Light Aircraft with Serial Hybrid Propulsion Systems},
  series = {Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen},
  booktitle = {Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen},
  pages     = {11 S.},
  year      = {2018},
  language  = {en}
}
@inproceedings{LudowicyRingsFingeretal.2018,
  author    = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten},
  title     = {Sizing Studies of Light Aircraft with Parallel Hybrid Propulsion Systems},
  series = {Deutscher Luft- und Raumfahrtkongress 2018},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2018},
  doi       = {10.25967/480227},
  pages     = {15 S.},
  year      = {2018},
  language  = {en}
}
@phdthesis{Dahmann1992,
  author    = {Dahmann, Peter},
  title     = {Untersuchungen zur Wirksamkeit von Filtern in hydraulischen Anlagen},
  pages     = {VI, 160 S. : Ill., graph. Darst.},
  year      = {1992},
  language  = {de}
}
@article{SaretzkiBergmannDahmannetal.2021,
  author    = {Saretzki, Charlotte and Bergmann, Ole and Dahmann, Peter and Janser, Frank and Keimer, Jona and Machado, Patricia and Morrison, Audry and Page, Henry and Pluta, Emil and St{\"u}bing, Felix and K{\"u}pper, Thomas},
  title     = {Are small airplanes safe with regards to COVID-19 transmission?},
  series = {Journal of Travel Medicine},
  volume    = {28},
  journal   = {Journal of Travel Medicine},
  number    = {7},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1708-8305},
  doi       = {10.1093/jtm/taab105},
  year      = {2021},
  language  = {en}
}
@inproceedings{WeissAbanteribaEsch2007,
  author    = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas},
  title     = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow},
  series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  publisher = {American Society of Mechanical Engineers (ASME)},
  address   = {New York},
  isbn      = {0-7918-4288-6},
  doi       = {10.1115/FEDSM2007-37387},
  pages     = {1861 -- 1871},
  year      = {2007},
  abstract  = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.},
  language  = {en}
}
@misc{GamgamiCzupallaGarciaetal.2016,
  author    = {Gamgami, Farid and Czupalla, Markus and Garcia, Antonio and Agnolon, David},
  title     = {From planetary transits to spacecraft design: achieving PLATO's pointing performance},
  series = {A7. Symposium on technological Requirement for future space astronomy and solar-system science missions},
  journal   = {A7. Symposium on technological Requirement for future space astronomy and solar-system science missions},
  year      = {2016},
  abstract  = {In the last decades, several hundred exoplanets could be detected thanks to space-based observatories, namely CNES' COROT and NASA's Kepler. To expand this quest ESA plans to launch CHEOPS as the f irst small class mission in the cosmic visions program (S1) and PLATO as the 3rd medium class mission, so called M3 . PLATO's primary objective is the detection of Earth like Exoplanets orbiting solar type stars in the habitable zone and characterisation of their bulk properties. This is possible by precise lightcurve measurement via 34 cameras. That said it becomes obvious that accurate pointing is key to achieve the required signal to noise ratio for positive transit detection. The paper will start with a comprehensive overview of PLATO's mission objectives and mission architecture. Hereafter, special focus will be devoted to PLATO's pointing requirements. Understanding the very nature of PLATO's pointing requirements is essential to derive a design baseline to achieve the required performance. The PLATO frequency domain is of particular interest, ranging from 40 mHz to 3 Hz. Due to the very different time-scales involved, the spectral pointing requirement is decomposed into a high frequency part dominated by the attitude control system and the low frequency part dominated by the thermo-elastic properties of the spacecraft's configuration. Both pose stringent constraints on the overall design as well as technology properties to comply with the derived requirements and thus assure a successful mission.},
  language  = {en}
}
@inproceedings{FunkeEschRoosen2009,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Peter},
  title     = {Using motor gasoline for aircrafts - coping with growing bio-fuel-caused risks by understanding cause-effect relationship},
  series = {Fuels 2009 : mineral oil based and alternative fuels ; 7th international colloquium ; January 14 - 15, 2009},
  booktitle = {Fuels 2009 : mineral oil based and alternative fuels ; 7th international colloquium ; January 14 - 15, 2009},
  editor    = {Bartz, Wilfried J.},
  publisher = {Technische Akademie Esslingen (TAE)},
  address   = {Ostfildern},
  isbn      = {978-3-924813-75-8},
  pages     = {237 -- 244},
  year      = {2009},
  abstract  = {The utilisation of vehicle-oriented gasoline in general aviation is very desirable for both ecological and economical reasons, as well as for general considerations of availability. As of today vehicle fuels may be used if the respective engine and cell are certified for such an operation. For older planes a supplementary technical certificate is provided for gasoline mixtures with less than 1 \% v/v ethanol only, though. Larger admixtures of ethanol may lead to sudden engine malfunction and should be considered as considerable security risks. Major problems are caused by the partially ethanol non-withstanding materials, a necessarily changed stochiometric adjustment of the engine for varying ethanol shares and the tendency for phase separation in the presence of absorbed water. The concepts of the flexible fuel vehicles are only partially applicable in the view of air security.},
  language  = {en}
}
@book{OPUS4-8743,
  title     = {Handbuch der Raumfahrttechnik},
  editor    = {Ley, Wilfried and Hallmann, Willi and Wittmann, Klaus},
  edition   = {5. Auflage},
  publisher = {Hanser},
  address   = {M{\"u}nchen},
  isbn      = {978-3-446-45429-3},
  pages     = {934 Seiten},
  year      = {2019},
  language  = {de}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Antriebssystemanpassungen zur Verwendung von LPG als Flugkraftstoff},
  series = {Motortechnische Zeitschrift (MTZ)},
  volume    = {2022},
  journal   = {Motortechnische Zeitschrift (MTZ)},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s35146-021-0778-2},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {Auch in der allgemeinen Luftfahrt w{\"a}re es w{\"u}nschenswert, die bereits vorhandenen Verbrennungsmotoren mit weniger CO₂-tr{\"a}chtigen Kraftstoffen als dem heute weit verbreiteten Avgas 100LL betreiben zu k{\"o}nnen. Es ist anzunehmen, dass im Vergleich die unter Normalbedingungen gasf{\"o}rmigen Kraftstoffe CNG, LPG oder LNG deutlich weniger Emissionen produzieren. Erforderliche Antriebssystemanpassungen wurden im Rahmen eines Forschungsprojekts an der FH Aachen untersucht.},
  language  = {de}
}
@incollection{RoethPielen2018,
  author    = {R{\"o}th, Thilo and Pielen, Michael},
  title     = {Personal Public Vehicle - ein urbanes Fahrzeugkonzept f{\"u}r die „Shared Mobility" der Zukunft},
  series = {Karosseriebautage Hamburg 2018, 16. ATZ-Fachtagung},
  booktitle = {Karosseriebautage Hamburg 2018, 16. ATZ-Fachtagung},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  doi       = {10.1007/978-3-658-22038-9_13},
  pages     = {189 -- 199},
  year      = {2018},
  abstract  = {Die urbane Mobilit{\"a}t ist im Wandel und insbesondere neue innovative Gesch{\"a}ftsmodelle werden einen wesentlichen Teil zur L{\"o}sung von k{\"u}nftigen Mobilit{\"a}tsbed{\"u}rfnissen beitragen. Die sogenannte „Shared Mobility" gilt aktuell neben der Elektrifizierung des Antriebes und autonomem Fahrzeugtechnologien als einer der wichtigsten Trendthemen in der Automobilindustrie. Neue Mobilit{\"a}tsdienstleistungen verlangen dabei verst{\"a}rkt auch neue Fahrzeugkonzepte.},
  language  = {de}
}
@inproceedings{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Case studies in initial sizing for hybrid-electric general aviation aircraft},
  series = {2018 AIAA/IEEE Electric Aircraft Technologies Symposium, Cincinnati, Ohio},
  booktitle = {2018 AIAA/IEEE Electric Aircraft Technologies Symposium, Cincinnati, Ohio},
  doi       = {10.2514/6.2018-5005},
  year      = {2018},
  language  = {en}
}
@inproceedings{SchopenShabaniEschetal.2022,
  author    = {Schopen, Oliver and Shabani, Bahman and Esch, Thomas and Kemper, Hans and Shah, Neel},
  title     = {Quantitative evaluation of health management designs for fuel cell systems in transport vehicles},
  series = {2nd UNITED-SAIG International Conference Proceedings},
  booktitle = {2nd UNITED-SAIG International Conference Proceedings},
  editor    = {Rahim, S.A. and As'arry, A. and Zuhri, M.Y.M. and Harmin, M.Y. and Rezali, K.A.M. and Hairuddin, A.A.},
  pages     = {1 -- 3},
  year      = {2022},
  abstract  = {Focusing on transport vehicles, mainly with regard to aviation applications, this paper presents compilation and subsequent quantitative evaluation of methods aimed at building an optimum integrated health management solution for fuel cell systems. The methods are divided into two different main types and compiled in a related scheme. Furthermore, different methods are analysed and evaluated based on parameters specific to the aviation context of this study. Finally, the most suitable method for use in fuel cell health management systems is identified and its performance and suitability is quantified.},
  language  = {en}
}
@phdthesis{Rosenkranz1989,
  author    = {Rosenkranz, Josef},
  title     = {Die Gleitlagergeh{\"a}usesteifigkeit als modaler Parameter f{\"u}r Rotorsysteme},
  address   = {Aachen},
  pages     = {VI, 145 S. : Ill., zahlr. graph. Darst.},
  year      = {1989},
  language  = {de}
}
@inproceedings{TamaldinEschTonolietal.2020,
  author    = {Tamaldin, Noreffendy and Esch, Thomas and Tonoli, Andrea and Reisinger, Karl Heinz and Sprenger, Hanna and Razuli, Hisham},
  title     = {ERASMUS+ United CBHE Automotive International Collaboration from European to South East Asia},
  series = {Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management},
  booktitle = {Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management},
  publisher = {IEOM Society International},
  address   = {Southfield},
  isbn      = {978-1-7923-6123-4},
  issn      = {2169-8767},
  pages     = {2970 -- 2972},
  year      = {2020},
  abstract  = {The industrial revolution especially in the IR4.0 era have driven many states of the art technologies to be introduced. The automotive industry as well as many other key industries have also been greatly influenced. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South East Asia (SEA). Indulging this situation, FH JOANNEUM, Austria together with European partners from FH Aachen, Germany and Politecnico di Torino, Italy are taking initiative to close down the gap utilizing the Erasmus+ United Capacity Building in Higher Education grant from EU. A consortium was founded to engage with automotive technology transfer using the European framework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries in respective countries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative and high-quality training courses to increase graduate's employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing University-industry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future.},
  language  = {en}
}
@article{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs},
  series = {CEAS Aeronautical Journal},
  volume    = {10},
  journal   = {CEAS Aeronautical Journal},
  number    = {3},
  publisher = {Springer},
  issn      = {1869-5582 print},
  doi       = {10.1007/s13272-018-0352-x},
  pages     = {843},
  year      = {2018},
  abstract  = {One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost-benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters.},
  language  = {en}
}
@inproceedings{Blome2018,
  author    = {Blome, Hans-Joachim},
  title     = {{\"U}ber die kulturelle Bedeutung der Raumfahrt},
  series = {{\"U}berleben im Weltraum. Auf dem Weg zu neuen Grenzen. 21. Berliner Kolloquium der Daimler und Benz Stiftung 24. Mai 2017},
  booktitle = {{\"U}berleben im Weltraum. Auf dem Weg zu neuen Grenzen. 21. Berliner Kolloquium der Daimler und Benz Stiftung 24. Mai 2017},
  pages     = {5 -- 5},
  year      = {2018},
  language  = {de}
}
@book{Wahle1994,
  author    = {Wahle, Michael},
  title     = {Kinetik. - (Dynamik ; 2)},
  edition   = {1. Aufl.},
  publisher = {Mainz},
  address   = {Aachen},
  isbn      = {3- 930085-94-1},
  pages     = {91 S. : graph. Darst.},
  year      = {1994},
  language  = {de}
}
@misc{Wahle1994,
  author    = {Wahle, Michael},
  title     = {Stoßd{\"a}mpfer : Offenlegungschrift / Europ{\"a}ische Patentschrift},
  publisher = {Deutsches Patent- und Markenamt / Europ{\"a}isches Patentamt},
  address   = {M{\"u}nchen / Den Hague},
  pages     = {7 S. : graph. Darst.},
  year      = {1994},
  language  = {de}
}
@misc{EickmannEschFunkeetal.2014,
  author    = {Eickmann, Matthias and Esch, Thomas and Funke, Harald and Abanteriba, Sylvester and Roosen, Petra},
  title     = {Biofuels in Aviation - Safety Implications of Bio-Ethanol Usage in General Aviation Aircraft},
  year      = {2014},
  abstract  = {Up in the clouds and above fuels and construction materials must be very carefully selected to ensure a smooth flight and touchdown. Out of around 38,000 single and dual-engined propeller aeroplanes, roughly a third are affected by a new trend in the fuel sector that may lead to operating troubles or even emergency landings: The admixture of bio-ethanol to conventional gasoline. Experiences with these fuels may be projected to alternative mixtures containing new components.},
  language  = {en}
}
@misc{WahleFriedrich1996,
  author    = {Wahle, Michael and Friedrich, Peter Ralph},
  title     = {Anordnung zur schwingungsisolierenden Lagerung von Massen oder elastischen Systemen : Offenlegungsschrift},
  publisher = {Deutsches Patent- und Markenamt},
  address   = {M{\"u}nchen},
  pages     = {8 S. : graph. Darst.},
  year      = {1996},
  language  = {de}
}
@book{Wahle1993,
  author    = {Wahle, Michael},
  title     = {Kinematik. - (Dynamik ; 1)},
  edition   = {1. Aufl.},
  publisher = {Mainz},
  address   = {Aachen},
  isbn      = {3-930085-25-9},
  pages     = {72 S. : graph. Darst.},
  year      = {1993},
  language  = {de}
}
@inproceedings{Czupalla2017,
  author    = {Czupalla, Markus},
  title     = {Pflanzen oder Maschinen - was l{\"a}ßt uns auf dem Mars {\"u}berleben?},
  series = {{\"U}berleben im Weltraum. Auf dem Weg zu neuen Grenzen. 21. Berliner Kolloquium der Daimler und Benz Stiftung 24. Mai 2017},
  booktitle = {{\"U}berleben im Weltraum. Auf dem Weg zu neuen Grenzen. 21. Berliner Kolloquium der Daimler und Benz Stiftung 24. Mai 2017},
  pages     = {12 -- 12},
  year      = {2017},
  language  = {de}
}
@misc{NonhoffWahle1990,
  author    = {Nonhoff, Gottfried and Wahle, Michael},
  title     = {Anordnung zur D{\"a}mpfung von Schwingungen an Bauwerken und Bauteilen : Offenlegungsschrift / Europ{\"a}ische Patentschrift},
  publisher = {Deutsches Patent- und Markenamt / Europ{\"a}isches Patentamt},
  address   = {M{\"u}nchen / Den Hague},
  pages     = {7 S. : graph. Darst.},
  year      = {1990},
  language  = {de}
}
@inproceedings{Rosenkranz1993,
  author    = {Rosenkranz, Josef},
  title     = {Verbesserung der Laufruhe des Verbrennungsmotors durch abgestimmte qualit{\"a}tssteigernde Maßnahmen beim Auswuchten des Kurbeltriebs},
  series = {Antriebstechnisches Kolloquium '93 / Industrieentwicklungen und Forschungsergebnisse f{\"u}r die Maschinen{\"u}berwachung und die Konstruktion in der Antriebstechnik. - (Reihe IME-Leitfaden)},
  booktitle = {Antriebstechnisches Kolloquium '93 / Industrieentwicklungen und Forschungsergebnisse f{\"u}r die Maschinen{\"u}berwachung und die Konstruktion in der Antriebstechnik. - (Reihe IME-Leitfaden)},
  publisher = {Verl. T{\"U}V Rheinland},
  address   = {K{\"o}ln},
  isbn      = {3-8249-0139-0},
  pages     = {176 -- 199},
  year      = {1993},
  language  = {de}
}
@incollection{DachwaldUlamecBiele2013,
  author    = {Dachwald, Bernd and Ulamec, Stephan and Biele, Jens},
  title     = {Clean in situ subsurface exploration of icy environments in the solar system},
  series = {Habitability of other planets and satellites. - (Cellular origin, life in extreme habitats and astrobiology ; 28)},
  booktitle = {Habitability of other planets and satellites. - (Cellular origin, life in extreme habitats and astrobiology ; 28)},
  publisher = {Springer},
  address   = {Dordrecht},
  isbn      = {978-94-007-6545-0 (Druckausgabe)},
  pages     = {367 -- 397},
  year      = {2013},
  abstract  = {"To assess the habitability of the icy environments in the solar system, for example, on Mars, Europa, and Enceladus, the scientific analysis of material embedded in or underneath their ice layers is very important. We consider self-steering robotic ice melting probes to be the best method to cleanly access these environments, that is, in compliance with planetary protection standards. The required technologies are currently developed and tested."},
  language  = {en}
}
@book{Wahle1999,
  author    = {Wahle, Michael},
  title     = {Angewandte Strukturanalyse. - (Dynamik)},
  publisher = {Mainz},
  address   = {Aachen},
  isbn      = {3-89653-567-6},
  pages     = {120, A41 S. : Ill., graph. Darst.},
  year      = {1999},
  language  = {de}
}
@misc{EcclestonDrummondMiddletonetal.2020,
  author    = {Eccleston, Paul and Drummond, Rachel and Middleton, Kevin and Bishop, Georgia and Caldwell, Andrew and Desjonqueres, Lucile and Tosh, Ian and Cann, Nick and Crook, Martin and Hills, Matthew and Pearson, Chris and Simpson, Caroline and Stamper, Richard and Tinetti, Giovanna and Pascale, Enzo and Swain, Mark and Holmes, Warren A. and Wong, Andre and Puig, Ludovic and Pilbratt, G{\"o}ran and Linder, Martin and Boudin, Nathalie and Ertel, Hanno and Gambicorti, Lisa and Halain, Jean-Philippe and Pace, Emanuele and Vilardell, Francesc and G{\´o}mez, Jos{\´e} M. and Colom{\´e}, Josep and Amiaux, J{\´e}r{\^o}me and Cara, Christophe and Berthe, Michel and Moreau, Vincent and Morgante, Gianluca and Malaguti, Giuseppe and Alonso, Gustavo and {\´A}lvarez, Javier P. and Ollivier, Marc and Philippon, Anne and Hellin, Marie-Laure and Roose, Steve and Frericks, Martin and Krijger, Matthijs and Rataj, Miroslaw and Wawer, Piotr and Skup, Konrad and Sobiecki, Mateusz and Christian Jessen, Niels and M{\o}ller Pedersen, S{\o}ren and Hargrave, Peter and Griffin, Matt and Ottensamer, Roland and Hunt, Thomas and Rust, Duncan and Saleh, Aymen and Winter, Berend and Focardi, Mauro and Da Deppo, Vania and Zuppella, Paola and Czupalla, Markus},
  title     = {The ARIEL payload: A technical overview},
  series = {Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave},
  volume    = {11443},
  journal   = {Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave},
  editor    = {Lystrup, Makenzie and Perrin, Marshall D. and Batalha, Natalie and Siegler, Nicholas and Tong, Edward C.},
  publisher = {SPIE},
  address   = {Washington},
  doi       = {10.1117/12.2561478},
  pages     = {114430Z},
  year      = {2020},
  abstract  = {The Atmospheric Remote-Sensing Infrared Exoplanet Large-survey, ARIEL, has been selected to be the next (M4) medium class space mission in the ESA Cosmic Vision programme. From launch in 2028, and during the following 4 years of operation, ARIEL will perform precise spectroscopy of the atmospheres of ~1000 known transiting exoplanets using its metre-class telescope. A three-band photometer and three spectrometers cover the 0.5 µm to 7.8 µm region of the electromagnetic spectrum. This paper gives an overview of the mission payload, including the telescope assembly, the FGS (Fine Guidance System) - which provides both pointing information to the spacecraft and scientific photometry and low-resolution spectrometer data, the ARIEL InfraRed Spectrometer (AIRS), and other payload infrastructure such as the warm electronics, structures and cryogenic cooling systems.},
  language  = {en}
}
@misc{ReiswichBrandtCzupalla2019,
  author    = {Reiswich, Martin and Brandt, Hannes and Czupalla, Markus},
  title     = {Passive thermal control by integration of phase change material into additively manufactured structures},
  series = {E2. 47th Student conference},
  journal   = {E2. 47th Student conference},
  year      = {2019},
  abstract  = {Optical Instruments require an extremely stable thermal surrounding to prevent loss of data quality by misalignments of the instrument components resulting from material deformation due to temperature f luctuations (e.g. from solar intrusion). Phase Change Material (PCM) can be applied as a thermal damper to achieve a more uniform temperature distribution. The challenge of this method is, among others, the integration of PCM into affected areas. If correctly designed, incoming heat is latently absorbed during phase change of the PCM, i.e. the temperature of a structure remains almost constant. In a cold phase, the heat during phase change is released again latently until the PCM returns to its original state of aggregation. Thus, the structure is thermally stabilized. At FH Aachen- University of Applied Sciences research is conducted to apply PCM directly into the structures of affected components (baffles, optical benches, electronic boxes, etc.). Through the application of Additive Manufacturing, the necessary voids are directly printed into these structures and filled later with PCM. Additive Manufacturing enables complex structures that would not have been possible with conservative manufacturing methods. A corresponding Breadboard was developed and manufactured by Selective Laser Melting (SLM). The current state of research includes the handling and analysis of the Breadboard, tests and a correlation of the thermal model. The results have shown analytically and practically that it is possible to use PCM as an integral part of the structure as a thermal damper. The results serve as a basis for the further development of the technology, which should maximize performance and enable the integration of PCM into much more complex structures.},
  language  = {en}
}
@misc{RainerRoestelWahle2006,
  author    = {Rainer, N{\"a}hle and R{\"o}stel, Reinhard and Wahle, Michael},
  title     = {Lagerungssystem in einem Raumfahrzeug : Patentschrift},
  publisher = {Deutsches Patent- und Markenamt},
  address   = {M{\"u}nchen},
  pages     = {7 S.: graph. Darst.},
  year      = {2006},
  language  = {de}
}
@misc{FeldmannFranckeEspeetal.2022,
  author    = {Feldmann, Marco and Francke, Gero and Espe, Clemes and Chen, Qian and Baader, Fabian and Boxberg, Marc S. and Sustrate, Anna-Marie and Kowalski, Julia and Dachwald, Bernd},
  title     = {Performance data of an ice-melting probe from field tests in two different ice environments},
  doi       = {10.5281/zenodo.6094866},
  year      = {2022},
  abstract  = {This dataset was acquired at field tests of the steerable ice-melting probe "EnEx-IceMole" (Dachwald et al., 2014). A field test in summer 2014 was used to test the melting probe's system, before the probe was shipped to Antarctica, where, in international cooperation with the MIDGE project, the objective of a sampling mission in the southern hemisphere summer 2014/2015 was to return a clean englacial sample from the subglacial brine reservoir supplying the Blood Falls at Taylor Glacier (Badgeley et al., 2017, German et al., 2021). The standardized log-files generated by the IceMole during melting operation include more than 100 operational parameters, housekeeping information, and error states, which are reported to the base station in intervals of 4 s. Occasional packet loss in data transmission resulted in a sparse number of increased sampling intervals, which where compensated for by linear interpolation during post processing. The presented dataset is based on a subset of this data: The penetration distance is calculated based on the ice screw drive encoder signal, providing the rate of rotation, and the screw's thread pitch. The melting speed is calculated from the same data, assuming the rate of rotation to be constant over one sampling interval. The contact force is calculated from the longitudinal screw force, which es measured by strain gauges. The used heating power is calculated from binary states of all heating elements, which can only be either switched on or off. Temperatures are measured at each heating element and averaged for three zones (melting head, side-wall heaters and back-plate heaters).},
  language  = {en}
}
@inproceedings{MayntzKeimerDahmannetal.2022,
  author    = {Mayntz, Joscha and Keimer, Jona and Dahmann, Peter and Hille, Sebastian and Stumpf, Eike and Fisher, Alex and Dorrington, Graham},
  title     = {Electrical Drive and Regeneration in General Aviation Flight with Propellers},
  series = {Deutscher Luft- und Raumfahrtkongress 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2020},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/530100},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {Electric flight has the potential for a more sustainable and energy-saving way of aviation compared to fossil fuel aviation. The electric motor can be used as a generator inflight to regenerate energy during descent. Three different approaches to regenerating with electric propeller powertrains are proposed in this paper. The powertrain is to be set up in a wind tunnel to determine the propeller efficiency in both working modes as well as the noise emissions. Furthermore, the planned flight tests are discussed. In preparation for these tests, a yaw stability analysis is performed with the result that the aeroplane is controllable during flight and in the most critical failure case. The paper shows the potential for inflight regeneration and addresses the research gaps in the dual role of electric powertrains for propulsion and regeneration of general aviation aircraft.},
  language  = {en}
}
@incollection{Wahle1997,
  author    = {Wahle, Michael},
  title     = {Strukturmechanische Auslegung von Elastomer-Bauteilen in der Schwingungstechnik},
  series = {Kolloquium anl{\"a}ßlich des 70. Geburtstags von H. {\"O}ry : [29.09.1997 - 30.09.1997, K{\´a}rm{\´a}n-Auditorium, H{\"o}rsaal FO5, RWTH Aachen]},
  booktitle = {Kolloquium anl{\"a}ßlich des 70. Geburtstags von H. {\"O}ry : [29.09.1997 - 30.09.1997, K{\´a}rm{\´a}n-Auditorium, H{\"o}rsaal FO5, RWTH Aachen]},
  editor    = {Reimerdes, Hans-G.},
  publisher = {Inst. f{\"u}r Leichtbau},
  address   = {Aachen},
  pages     = {175 -- 188},
  year      = {1997},
  language  = {de}
}
@misc{Wahle1989,
  author    = {Wahle, Michael},
  title     = {Gestaltung von plattenf{\"o}rmigen Hohlprofilen oder wellblechartigen Profilen : Offenlegungsschrift / Europ{\"a}ische Patentschrift},
  publisher = {Deutsches Patent- und Markenamt / Europ{\"a}isches Patentamt},
  address   = {M{\"u}nchen / Den Hague},
  pages     = {8 S. : graph. Darst.},
  year      = {1989},
  language  = {de}
}
@article{FayyaziSardarThomasetal.2023,
  author    = {Fayyazi, Mojgan and Sardar, Paramjotsingh and Thomas, Sumit Infent and Daghigh, Roonak and Jamali, Ali and Esch, Thomas and Kemper, Hans and Langari, Reza and Khayyam, Hamid},
  title     = {Artificial intelligence/machine learning in energy management systems, control, and optimization of hydrogen fuel cell vehicles},
  volume    = {15},
  number    = {6},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/su15065249},
  pages     = {38},
  year      = {2023},
  abstract  = {Environmental emissions, global warming, and energy-related concerns have accelerated the advancements in conventional vehicles that primarily use internal combustion engines. Among the existing technologies, hydrogen fuel cell electric vehicles and fuel cell hybrid electric vehicles may have minimal contributions to greenhouse gas emissions and thus are the prime choices for environmental concerns. However, energy management in fuel cell electric vehicles and fuel cell hybrid electric vehicles is a major challenge. Appropriate control strategies should be used for effective energy management in these vehicles. On the other hand, there has been significant progress in artificial intelligence, machine learning, and designing data-driven intelligent controllers. These techniques have found much attention within the community, and state-of-the-art energy management technologies have been developed based on them. This manuscript reviews the application of machine learning and intelligent controllers for prediction, control, energy management, and vehicle to everything (V2X) in hydrogen fuel cell vehicles. The effectiveness of data-driven control and optimization systems are investigated to evolve, classify, and compare, and future trends and directions for sustainability are discussed.},
  language  = {en}
}
@misc{WahlePeter1992,
  author    = {Wahle, Michael and Peter, Roland},
  title     = {Bismaleinimidharze : Offenlegungsschrift / Europ{\"a}ische Patentanmeldung},
  publisher = {Deutsches Patent- und Markenamt / Europ{\"a}isches Patentamt},
  address   = {M{\"u}nchen / Den Hague},
  pages     = {6 S. : graph. Darst.},
  year      = {1992},
  language  = {de}
}
@inproceedings{Finger2016,
  author    = {Finger, Felix},
  title     = {Comparative Performance and Benefit Assessment of VTOL and CTOL UAVs},
  series = {Deutscher Luft- und Raumfahrtkongress (DLRK) 2016, 13.-15.9.2016},
  booktitle = {Deutscher Luft- und Raumfahrtkongress (DLRK) 2016, 13.-15.9.2016},
  pages     = {10 Seiten},
  year      = {2016},
  language  = {en}
}
@inproceedings{PeekenTroederSchmidtetal.1985,
  author    = {Peeken, Heinz and Troeder, Christoph and Schmidt, J. and Rosenkranz, Josef},
  title     = {Principles of machine noise reduction},
  series = {Inter-noise 85 : proceedings ; 1985 international conference on noise control engineering ; Munich, Sept. 18 - 20, 1985. - (Schriftenreihe der Bundesanstalt f{\"u}r Arbeitsschutz : Tagungsbericht ; 39)},
  booktitle = {Inter-noise 85 : proceedings ; 1985 international conference on noise control engineering ; Munich, Sept. 18 - 20, 1985. - (Schriftenreihe der Bundesanstalt f{\"u}r Arbeitsschutz : Tagungsbericht ; 39)},
  publisher = {Bundesanstalt f{\"u}r Arbeitsschutz [u.a.]},
  address   = {Dortmund [u.a.]},
  isbn      = {3-88314-417-7},
  pages     = {23 -- 36},
  year      = {1985},
  language  = {en}
}
@article{HennPolaczek2007,
  author    = {Henn, Gudrun and Polaczek, Christa},
  title     = {Studienerfolg in den Ingenieurwissenschaften},
  series = {Das Hochschulwesen : HSW ; Forum f{\"u}r Hochschulforschung, -praxis und -politik},
  volume    = {55},
  journal   = {Das Hochschulwesen : HSW ; Forum f{\"u}r Hochschulforschung, -praxis und -politik},
  number    = {5},
  issn      = {0018-2974},
  pages     = {144 -- 147},
  year      = {2007},
  language  = {de}
}
@article{Esch2010,
  author    = {Esch, Thomas},
  title     = {Trends in commercial vehicle powertrains},
  series = {ATZautotechnology},
  volume    = {2010},
  journal   = {ATZautotechnology},
  number    = {10},
  publisher = {Vieweg \& Sohn},
  address   = {Wiesbaden},
  issn      = {2192-886X},
  doi       = {10.1007/BF03247185},
  pages     = {26 -- 31},
  year      = {2010},
  abstract  = {Low emission zones and truck bans, the rising price of diesel and increases in road tolls: all of these factors are putting serious pressure on the transport industry. Commercial vehicle manufacturers and their suppliers are in the process of identifying new solutions to these challenges as part of their efforts to meet the EEV (enhanced environmentally friendly vehicle) limits, which are currently the most robust European exhaust and emissions standards for trucks and buses.},
  language  = {en}
}
@article{GenzKingWahle1992,
  author    = {Genz, M. and King, H. and Wahle, Michael},
  title     = {Mikrozellige Polyurethan-Elastomere als Federelement in Automobilanwendungen},
  series = {Automobiltechnische Zeitschrift ; ATZ},
  volume    = {94},
  journal   = {Automobiltechnische Zeitschrift ; ATZ},
  number    = {10},
  issn      = {0001-2785},
  pages     = {512 -- 520},
  year      = {1992},
  language  = {de}
}
@misc{Polaczek1983,
  author    = {Polaczek, Christa},
  title     = {Kofaser - Kategorien und differentielle Algebren},
  publisher = {Math. Inst. der Univ.},
  address   = {Bonn},
  pages     = {178 S. : Anh.},
  year      = {1983},
  language  = {de}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Powertrain Adaptions for LPG Usage in General Aviation},
  series = {MTZ worldwide},
  volume    = {2022},
  journal   = {MTZ worldwide},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s38313-021-0756-6},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {In general aviation, too, it is desirable to be able to operate existing internal combustion engines with fuels that produce less CO₂ than Avgas 100LL being widely used today It can be assumed that, in comparison, the fuels CNG, LPG or LNG, which are gaseous under normal conditions, produce significantly lower emissions. Necessary propulsion system adaptations were investigated as part of a research project at Aachen University of Applied Sciences.},
  language  = {en}
}
@misc{SalberPischingerEschetal.1998,
  author    = {Salber, Wolfgang and Pischinger, Martin and Esch, Thomas and Hagen, J{\"u}rgen},
  title     = {Kaltstartverfahren f{\"u}r eine drosselfreie Mehrzylinder-Kolbenbrennkraftmaschine},
  year      = {1998},
  abstract  = {Die Erfindung betrifft ein Kaltstartverfahren f{\"u}r eine Mehrzylinder-Kolbenbrennkraftmaschine mit Anlasser und einer Motorsteuerung zur Ansteuerung von Kraftstoffeinspritzeinrichtungen, Z{\"u}ndung und voll variabel elektromagnetisch bet{\"a}tigbaren Gaswechselventilen an den einzelnen Zylindern, bei dem die Kurbelwelle {\"u}ber den Anlasser gedreht wird und zum Start f{\"u}r wenigstens einen Zylinder die dazugeh{\"o}rigen Gaswechselventile, die Kraftstoffeinspritzeinrichtung und die Z{\"u}ndung in einem vorgegebenen Taktzyklus angesteuert werden und zwar in den ersten Arbeitszyklen mit "Sp{\"a}tem Einlaß {\"O}ffnen".},
  language  = {de}
}
@misc{PischingerEschDuesmann2006,
  author    = {Pischinger, Martin and Esch, Thomas and Duesmann, Klaus},
  title     = {Elektromagnetischer Aktuator mit gelenkig abgest{\"u}tzter R{\"u}ckstellfeder},
  year      = {2006},
  abstract  = {Die Erfindung betrifft einen elektromagnetischen Aktuator zur Bet{\"a}tigung eines Stellgliedes (7) mit wenigstens einem gesteuert bestrombaren Elektromagneten (1, 2) und einem mit dem Stellglied (7) in Wirkverbindung stehenden Anker (5), der bei Bestromung des Elektromagneten (1, 2) gegen die Kraft wenigstens einer an einem Geh{\"a}use (12) abgest{\"u}tzten R{\"u}ckstellfeder (10) an der Polfl{\"a}che (3, 4) des Elektromagneten (1, 2) zur Anlage kommt, und daß zumindest der Anker (5) {\"u}ber eine sph{\"a}rische Gelenkanordnung (11) auf der R{\"u}ckstellfeder (10) abgest{\"u}tzt ist.},
  language  = {de}
}
@inproceedings{SchopenKemperEsch2021,
  author    = {Schopen, Oliver and Kemper, Hans and Esch, Thomas},
  title     = {Development of a comparison methodology and evaluation matrix for electrically driven compressors in ICE and FC},
  series = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  booktitle = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  publisher = {FH Joanneum},
  address   = {Graz},
  isbn      = {978-3-902103-94-9},
  pages     = {45 -- 46},
  year      = {2021},
  abstract  = {In addition to electromobility and alternative drive systems, a focus is set on electrically driven compressors (EDC), with a high potential for increasing the efficiency of internal combustion engines (ICE) and fuel cells [01]. The primary objective is to increase the ICE torque, provided independently of the ICE speed by compressing the intake air and consequently the ICE filling level supported by the compressor. For operation independent from the ICE speed, the EDC compressor is decoupled from the turbine by using an electric compressor motor (CM) instead of the turbine. ICE performances can be increased by the use of EDC where individual compressor parameters are adapted to the respective application area [02] [03]. This task contains great challenges, increased by demands with regard to pollutant reduction while maintaining constant performance and reduced fuel consumption. The FH-Aachen is equipped with an EDC test bench which enables EDC-investigations in various configurations and operating modes. Characteristic properties of different compressors can be determined, which build the basis for a comparison methodology. Subject of this project is the development of a comparison methodology for EDC with an associated evaluation method and a defined overall evaluation method. For the application of this comparison methodology, corresponding series of measurements are carried out on the EDC test bench using an appropriate test device.},
  language  = {en}
}
@inproceedings{FunkeHajAyedKustereretal.2014,
  author    = {Funke, Harald and Haj Ayed, A. and Kusterer, K. and Keinz, Jan and Kazari, M. and Kitajima, J. and Horikawa, A. and Okada, K.},
  title     = {Numerical Study on Increased Energy Density for the DLN Micromix Hydrogen Combustion Principle},
  series = {Combustion, Fuels and Emissions (ASME Turbo Expo 2014: Turbine Technical Conference and Exposition : D{\"u}sseldorf, Germany, June 16-20, 2014 ; Vol. 4A)},
  booktitle = {Combustion, Fuels and Emissions (ASME Turbo Expo 2014: Turbine Technical Conference and Exposition : D{\"u}sseldorf, Germany, June 16-20, 2014 ; Vol. 4A)},
  publisher = {ASME},
  address   = {New York, N.Y.},
  isbn      = {978-0-7918-4568-4},
  pages     = {V04AT04A057},
  year      = {2014},
  language  = {en}
}
@misc{Wahle1990,
  author    = {Wahle, Michael},
  title     = {Anordnung zum D{\"a}mpfen von Schwingungen elastischer Systeme : Offenlegungsschrift / Europ{\"a}ische Patentschrift},
  publisher = {Deutsches Patent- und Markenamt / Europ{\"a}isches Patentamt},
  address   = {M{\"u}nchen / Den Hague},
  pages     = {6 S. : graph. Darst.},
  year      = {1990},
  language  = {de}
}
@article{DachwaldWurm2011,
  author    = {Dachwald, Bernd and Wurm, Patrick},
  title     = {Mission analysis and performance comparison for an Advanced Solar Photon Thruster},
  series = {Advances in Space Research},
  volume    = {48},
  journal   = {Advances in Space Research},
  number    = {11},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  pages     = {1858 -- 1868},
  year      = {2011},
  language  = {en}
}
@article{ScholzLeyDachwaldetal.2010,
  author    = {Scholz, A. and Ley, Wilfried and Dachwald, Bernd and Miau, J. J. and Juang, J. C.},
  title     = {Flight results of the COMPASS-1 picosatellite mission},
  series = {Acta Astronautica. 67 (2010), H. 9-10},
  journal   = {Acta Astronautica. 67 (2010), H. 9-10},
  isbn      = {0094-5765},
  pages     = {1289 -- 1298},
  year      = {2010},
  language  = {en}
}