@article{RamoshabaHuismanLammertynetal.2020,
  author    = {Ramoshaba, Nthai E. and Huisman, Hugo W. and Lammertyn, Leandi and Kotliar, Konstantin and Schutte, Aletta E. and Smith, Wayne},
  title     = {Retinal microvasculature and masked hypertension in young adults: the African-PREDICT study},
  series = {Hypertension Research},
  journal   = {Hypertension Research},
  number    = {43},
  publisher = {Springer Nature},
  address   = {Osaka},
  issn      = {1348-4214},
  doi       = {10.1038/s41440-020-0487-0},
  pages     = {1231 -- 1238},
  year      = {2020},
  abstract  = {Masked hypertension is known to induce microvascular complications. However, it is unclear whether early microvascular changes are already occurring in young, otherwise healthy adults. We therefore investigated whether retinal microvascular calibers and acute responses to a flicker stimulus are related to masked hypertension. We used the baseline data of 889 participants aged 20-30 years who were taking part in the African Prospective study on the Early Detection and Identification of Cardiovascular Disease and Hypertension. Clinic and 24-h ambulatory blood pressure were measured. The central retinal artery equivalent (CRAE) and central retinal vein equivalent were calculated from fundus images, and retinal vessel dilation was determined in response to flicker light-induced provocation. A smaller CRAE was observed in those with masked hypertension vs. those with normotension (157.1 vs. 161.2 measuring units, P < 0.001). In forward multivariable-adjusted regression analysis, only CRAE was negatively related to masked hypertension [adjusted R² = 0.267, β = -0.097 (95\% CI = -0.165; -0.029), P = 0.005], but other retinal microvascular parameters were not associated with masked hypertension. In multivariable logistic regression analyses, masked hypertension [OR = 2.333, (95\% CI = 1.316; 4.241), P = 0.004] was associated with a narrower CRAE. In young healthy adults, masked hypertension was associated with retinal arteriolar narrowing, thereby reflecting early microvascular alterations known to predict cardiovascular outcomes in later life.},
  language  = {en}
}
@article{SmithKotliarLammertynetal.2020,
  author    = {Smith, Wayne and Kotliar, Konstantin and Lammertyn, Leandi and Ramoshaba, Nthai E. and Vilser, Walthard and Huisman, Hugo W. and Schutte, Aletta E.},
  title     = {Retinal vessel caliber and caliber responses in true normotensive black and white adults: The African-PREDICT study},
  series = {Microvascular Research},
  volume    = {128},
  journal   = {Microvascular Research},
  number    = {Article 103937},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0026-2862},
  doi       = {10.1016/j.mvr.2019.103937},
  year      = {2020},
  abstract  = {Purpose Globally, a detrimental shift in cardiovascular disease risk factors and a higher mortality level are reported in some black populations. The retinal microvasculature provides early insight into the pathogenesis of systemic vascular diseases, but it is unclear whether retinal vessel calibers and acute retinal vessel functional responses differ between young healthy black and white adults. Methods We included 112 black and 143 white healthy normotensive adults (20-30 years). Retinal vessel calibers (central retinal artery and vein equivalent (CRAE and CRVE)) were calculated from retinal images and vessel caliber responses to flicker light induced provocation (FLIP) were determined. Additionally, ambulatory blood pressure (BP), anthropometry and blood samples were collected. Results The groups displayed similar 24 h BP profiles and anthropometry (all p > .24). Black participants demonstrated a smaller CRAE (158 ± 11 vs. 164 ± 11 MU, p < .001) compared to the white group, whereas CRVE was similar (p = .57). In response to FLIP, artery maximal dilation was greater in the black vs. white group (5.6 ± 2.1 vs. 3.3 ± 1.8\%; p < .001). Conclusions Already at a young age, healthy black adults showed narrower retinal arteries relative to the white population. Follow-up studies are underway to show if this will be related to increased risk for hypertension development. The reason for the larger vessel dilation responses to FLIP in the black population is unclear and warrants further investigation.},
  language  = {en}
}
@article{NeumaierKotliarHaerenetal.2021,
  author    = {Neumaier, Felix and Kotliar, Konstantin and Haeren, Roel Hubert Louis and Temel, Yasin and L{\"u}ke, Jan Niklas and Seyam, Osama and Lindauer, Ute and Clusmann, Hans and Hescheler, J{\"u}rgen and Schubert, Gerrit Alexander and Schneider, Toni and Albanna, Walid},
  title     = {Retinal Vessel Responses to Flicker Stimulation Are Impaired in Ca v 2.3-Deficient Mice—An in- vivo Evaluation Using Retinal Vessel Analysis (RVA)},
  series = {Frontiers in Neurology},
  volume    = {12},
  journal   = {Frontiers in Neurology},
  publisher = {Frontiers},
  doi       = {10.3389/fneur.2021.659890},
  pages     = {1 -- 11},
  year      = {2021},
  language  = {en}
}
@inproceedings{HauggKreyerKemperetal.2020,
  author    = {Haugg, Albert Thomas and Kreyer, J{\"o}rg and Kemper, Hans and Hatesuer, Katerina and Esch, Thomas},
  title     = {Heat exchanger for ORC. adaptability and optimisation potentials},
  series = {IIR International Rankine 2020 Conference},
  booktitle = {IIR International Rankine 2020 Conference},
  doi       = {10.18462/iir.rankine.2020.1224},
  pages     = {10 Seiten},
  year      = {2020},
  abstract  = {The recovery of waste heat requires heat exchangers to extract it from a liquid or gaseous medium into another working medium, a refrigerant. In Organic Rankine Cycles (ORC) on Combustion Engines there are two major heat sources, the exhaust gas and the water/glycol fluid from the engine's cooling circuit. A heat exchanger design must be adapted to the different requirements and conditions resulting from the heat sources, fluids, system configurations, geometric restrictions, and etcetera. The Stacked Shell Cooler (SSC) is a new and very specific design of a plate heat exchanger, created by AKG, which allows with a maximum degree of freedom the optimization of heat exchange rate and the reduction of the related pressure drop. This optimization in heat exchanger design for ORC systems is even more important, because it reduces the energy consumption of the system and therefore maximizes the increase in overall efficiency of the engine.},
  language  = {en}
}
@incollection{AtmaneHirechKassmietal.2020,
  author    = {Atmane, Ilias and Hirech, Kamal and Kassmi, K. and Mahdi, Zahra and Alexopoulos, Spiros and Schwarzer, Klemens and Chayeb, H. and Bachiri, N.},
  title     = {Design and realization of a pilot solar desalination plant in Douar El Hamri in the province of Berkane (Morocco)},
  series = {Sustainable entrepreneurship, renewable energy-based projects, and digitalization},
  booktitle = {Sustainable entrepreneurship, renewable energy-based projects, and digitalization},
  editor    = {Omrane, Amina and Kassmi, Khalil and Akram, Muhammad Wasim and Khanna, Ashish and Mostafiz, Imtiaz},
  publisher = {CRC Press},
  address   = {Boca Raton, Fa.},
  isbn      = {9781000292541 (E-Book)},
  pages     = {18 Seiten},
  year      = {2020},
  abstract  = {Producing fresh water from saline water has become one of the most difficult challenges to overcome especially with the high demand and shortage of fresh water. In this context, as part of a collaboration with Germany, the authors propose a design and implementation of a pilot multi-stage solar desalination system (MSD), remotely controlled, at Douar Al Hamri in the rural town of Boughriba in the province of Berkane, Morocco. More specifically, they present their contribution on the remote control and supervision system, which makes the functioning of the MSD system reliable and guarantees the production of drinking water for the population of Douar. The results obtained show that the electronic cards and computer communication software implemented allow the acquisition of all electrical (currents, voltages, powers, yields), thermal (temperatures of each stage), and meteorological (irradiance and ambient temperature), remote control and maintenance (switching on, off, data transfer). By comparing with the literature carried out in the field of solar energy, the authors conclude that the MSD and electronic desalination systems realized during this work represent a contribution in terms of the reliability and durability of providing drinking water in rural and urban areas.},
  language  = {en}
}
@inproceedings{AlexopoulosBreitbachHoffschmidt2009,
  author    = {Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard},
  title     = {Optimization of the channel form geometry of porous ReSiC ceramic membrane modules},
  series = {Proceedings / International Conference \& Exhibition for Filtration and Separation Technology, FILTECH 2009 : October 13 - 15, 2009, Wiesbaden, Germany. Vol. 2},
  booktitle = {Proceedings / International Conference \& Exhibition for Filtration and Separation Technology, FILTECH 2009 : October 13 - 15, 2009, Wiesbaden, Germany. Vol. 2},
  publisher = {Filtech Exhibitions Germany},
  address   = {Meerbusch},
  isbn      = {978-3-941655-36-2},
  pages     = {686 -- 693},
  year      = {2009},
  language  = {en}
}
@article{DegeringEggertPulsetal.2010,
  author    = {Degering, Christian and Eggert, Thorsten and Puls, Michael and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and Jaeger, Karl-Erich},
  title     = {Optimization of protease secretion in Bacillus subtilis and Bacillus licheniformis by screening of homologous and herologous signal peptides},
  series = {Applied and environmental microbiology},
  volume    = {76},
  journal   = {Applied and environmental microbiology},
  number    = {19},
  publisher = {American Society for Microbiology},
  address   = {Washington, DC},
  issn      = {1098-5336 (E-Journal); 0003-6919 (Print); 0099-2240 (Print)},
  doi       = {10.1128/AEM.01146-10},
  pages     = {6370 -- 6378},
  year      = {2010},
  abstract  = {Bacillus subtilis and Bacillus licheniformis are widely used for the large-scale industrial production of proteins. These strains can efficiently secrete proteins into the culture medium using the general secretion (Sec) pathway. A characteristic feature of all secreted proteins is their N-terminal signal peptides, which are recognized by the secretion machinery. Here, we have studied the production of an industrially important secreted protease, namely, subtilisin BPN′ from Bacillus amyloliquefaciens. One hundred seventy-three signal peptides originating from B. subtilis and 220 signal peptides from the B. licheniformis type strain were fused to this secretion target and expressed in B. subtilis, and the resulting library was analyzed by high-throughput screening for extracellular proteolytic activity. We have identified a number of signal peptides originating from both organisms which produced significantly increased yield of the secreted protease. Interestingly, we observed that levels of extracellular protease were improved not only in B. subtilis, which was used as the screening host, but also in two different B. licheniformis strains. To date, it is impossible to predict which signal peptide will result in better secretion and thus an improved yield of a given extracellular target protein. Our data show that screening a library consisting of homologous and heterologous signal peptides fused to a target protein can identify more-effective signal peptides, resulting in improved protein export not only in the original screening host but also in different production strains.},
  language  = {en}
}
@article{DeppeBongaertsO'Connelletal.2011,
  author    = {Deppe, Veronika Maria and Bongaerts, Johannes and O'Connell, Timothy and Maurer, Karl-Heinz and Meinhardt, Friedhelm},
  title     = {Enzymatic deglycation of Amadori products in bacteria},
  series = {Applied microbiology and biotechnology},
  volume    = {Vol. 90},
  journal   = {Applied microbiology and biotechnology},
  number    = {Iss. 2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1432-0614 (E-Journal); 0171-1741 (Print); 0175-7598 (Print); 0340-2118 (Print)},
  pages     = {399 -- 406},
  year      = {2011},
  language  = {en}
}
@inproceedings{AhlbrinkAlexopoulosAnderssonetal.2009,
  author    = {Ahlbrink, N. and Alexopoulos, Spiros and Andersson, J. and Belhomme, B. and Teixeira Boura, Cristiano Jos{\´e} and Gall, J. and Hirsch, T.},
  title     = {viCERP - the Virtual Institute of Central Receiver Power Plant},
  series = {MATHMOD 2009 - 6th Vienna International Conference on Mathematical Modelling : February 11 - 13, 2009, Vienna, Austria. ARGESIM Report. No. 35},
  booktitle = {MATHMOD 2009 - 6th Vienna International Conference on Mathematical Modelling : February 11 - 13, 2009, Vienna, Austria. ARGESIM Report. No. 35},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-3-901608-35-3},
  year      = {2009},
  language  = {en}
}
@article{AlexopoulosHoffschmidt2017,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard},
  title     = {Advances in solar tower technology},
  series = {Wiley interdisciplinary reviews : Energy and Environment : WIREs},
  volume    = {6},
  journal   = {Wiley interdisciplinary reviews : Energy and Environment : WIREs},
  number    = {1},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2041-840X},
  doi       = {10.1002/wene.217},
  pages     = {1 -- 19},
  year      = {2017},
  language  = {en}
}
@article{FunkeBeckmannKeinzetal.2018,
  author    = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester},
  title     = {Comparison of Numerical Combustion Models for Hydrogen and Hydrogen-Rich Syngas Applied for Dry-Low-Nox-Micromix-Combustion},
  series = {Journal of Engineering for Gas Turbines and Power},
  volume    = {140},
  journal   = {Journal of Engineering for Gas Turbines and Power},
  number    = {8},
  publisher = {ASME},
  address   = {New York, NY},
  issn      = {0742-4795},
  doi       = {10.1115/1.4038882},
  pages     = {9 Seiten},
  year      = {2018},
  abstract  = {The Dry-Low-NOx (DLN) Micromix combustion technology has been developed as low emission combustion principle for industrial gas turbines fueled with hydrogen or syngas. The combustion process is based on the phenomenon of jet-in-crossflow-mixing (JICF). Fuel is injected perpendicular into the air-cross-flow and burned in a multitude of miniaturized, diffusion-like flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. In the Micromix research approach, computational fluid dynamics (CFD) analyses are validated toward experimental results. The combination of numerical and experimental methods allows an efficient design and optimization of DLN Micromix combustors concerning combustion stability and low NOx emissions. The paper presents a comparison of several numerical combustion models for hydrogen and hydrogen-rich syngas. They differ in the complexity of the underlying reaction mechanism and the associated computational effort. The performance of a hybrid eddy-break-up (EBU) model with a one-step global reaction is compared to a complex chemistry model and a flamelet generated manifolds (FGM) model, both using detailed reaction schemes for hydrogen or syngas combustion. Validation of numerical results is based on exhaust gas compositions available from experimental investigation on DLN Micromix combustors. The conducted evaluation confirms that the applied detailed combustion mechanisms are able to predict the general physics of the DLN-Micromix combustion process accurately. The FGM method proved to be generally suitable to reduce the computational effort while maintaining the accuracy of detailed chemistry.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@article{MuschallikMolinnusBongaertsetal.2017,
  author    = {Muschallik, Lukas and Molinnus, Denise and Bongaerts, Johannes and Pohl, Martina and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Siegert, Petra and Selmer, Thorsten},
  title     = {(R,R)-Butane-2,3-diol Dehydrogenase from Bacillus clausii DSM 8716T: Cloning and Expression of the bdhA-Gene, and Initial Characterization of Enzyme},
  series = {Journal of Biotechnology},
  volume    = {258},
  journal   = {Journal of Biotechnology},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0168-1656},
  doi       = {10.1016/j.jbiotec.2017.07.020},
  pages     = {41 -- 50},
  year      = {2017},
  abstract  = {The gene encoding a putative (R,R)-butane-2,3-diol dehydrogenase (bdhA) from Bacillus clausii DSM 8716T was isolated, sequenced and expressed in Escherichia coli. The amino acid sequence of the encoded protein is only distantly related to previously studied enzymes (identity 33-43\%) and exhibited some uncharted peculiarities. An N-terminally StrepII-tagged enzyme variant was purified and initially characterized. The isolated enzyme catalyzed the (R)-specific oxidation of (R,R)- and meso-butane-2,3-diol to (R)- and (S)-acetoin with specific activities of 12 U/mg and 23 U/mg, respectively. Likewise, racemic acetoin was reduced with a specific activity of up to 115 U/mg yielding a mixture of (R,R)- and meso-butane-2,3-diol, while the enzyme reduced butane-2,3-dione (Vmax 74 U/mg) solely to (R,R)-butane-2,3-diol via (R)-acetoin. For these reactions only activity with the co-substrates NADH/NAD+ was observed. The enzyme accepted a selection of vicinal diketones, α-hydroxy ketones and vicinal diols as alternative substrates. Although the physiological function of the enzyme in B. clausii remains elusive, the data presented herein clearly demonstrates that the encoded enzyme is a genuine (R,R)-butane-2,3-diol dehydrogenase with potential for applications in biocatalysis and sensor development.},
  language  = {en}
}
@incollection{ReimerBraunBallmann2007,
  author    = {Reimer, Lars and Braun, Carsten and Ballmann, Josef},
  title     = {Computational study of the aeroelastic equilibrium configuration of a swept wind tunnel wing model in subsonic flow},
  series = {High performance computing in science and engineering '06. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2006 / Wolfgang E. Nagel ... Eds.},
  booktitle = {High performance computing in science and engineering '06. Transactions of the High Performance Computing Center Stuttgart (HLRS) 2006 / Wolfgang E. Nagel ... Eds.},
  publisher = {Springer},
  address   = {Berlin [u.a.]},
  isbn      = {978-3-540-36165-7},
  pages     = {421 -- 434},
  year      = {2007},
  abstract  = {In the Collaborative Research Center SFB 401 at RWTH Aachen University, the numerical aeroelastic method SOFIA for direct numerical aeroelastic simulation is being progressively developed. Numerical results obtained by applying SOFIA were compared with measured data of static and dynamic aeroelastic wind tunnel tests for an elastic swept wing in subsonic flow.},
  language  = {en}
}
@article{JossekBongaertsSprenger2001,
  author    = {Jossek, Ralf and Bongaerts, Johannes and Sprenger, Georg A.},
  title     = {Characterization of a new feedback-resistant 3-deoxy-D-arabinoheptulosonate 7-phosphate synthase AroF of Escherichia coli},
  series = {FEMS microbiology letters},
  volume    = {Vol. 202},
  journal   = {FEMS microbiology letters},
  number    = {Iss. 1},
  issn      = {1574-6968},
  pages     = {145 -- 148},
  year      = {2001},
  language  = {en}
}
@article{GeierLehnertzBialonski2015,
  author    = {Geier, Christian and Lehnertz, Klaus and Bialonski, Stephan},
  title     = {Time-dependent degree-degree correlations in epileptic brain networks: from assortative to dissortative mixing},
  series = {Frontiers in Human Neuroscience},
  journal   = {Frontiers in Human Neuroscience},
  publisher = {Frontiers Research Foundation},
  address   = {Lausanne},
  issn      = {1662-5161},
  doi       = {10.3389/fnhum.2015.00462},
  year      = {2015},
  language  = {en}
}
@article{WilmingBegemannKuhneetal.2013,
  author    = {Wilming, Anja and Begemann, Jens and Kuhne, Stefan and Regestein, Lars and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and B{\"u}chs, Jochen},
  title     = {Metabolic studies of γ-polyglutamic acid production in Bacillus licheniformis by small-scale continuous cultivations},
  series = {Biochemical engineering journal},
  volume    = {Vol. 73},
  journal   = {Biochemical engineering journal},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-295X (E-Journal); 1369-703X (Print)},
  pages     = {29 -- 37},
  year      = {2013},
  language  = {en}
}
@article{Alexopoulos2015,
  author    = {Alexopoulos, Spiros},
  title     = {Simulation model for the transient process behaviour of solar aluminium recycling in a rotary kiln},
  series = {Applied Thermal Engineering},
  volume    = {78},
  journal   = {Applied Thermal Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-4311},
  doi       = {10.1016/j.applthermaleng.2015.01.007},
  pages     = {387 -- 396},
  year      = {2015},
  language  = {en}
}
@inproceedings{FunkeBeckmannKeinzetal.2017,
  author    = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester},
  title     = {Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications},
  series = {Proceedings of the ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. Volume 4B: Combustion, Fuels and Emissions. Charlotte, North Carolina, USA. June 26-30, 2017},
  booktitle = {Proceedings of the ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. Volume 4B: Combustion, Fuels and Emissions. Charlotte, North Carolina, USA. June 26-30, 2017},
  publisher = {ASME},
  address   = {New York},
  isbn      = {978-0-7918-5085-5},
  doi       = {10.1115/GT2017-64795},
  year      = {2017},
  abstract  = {The Dry-Low-NOx (DLN) Micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The non-premixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 Vol.\%) Micromix combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel Micromix combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas the evaluated dual-fuel Micromix prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.},
  language  = {en}
}
@article{BoehnischBraunMuscarelloetal.2024,
  author    = {B{\"o}hnisch, Nils and Braun, Carsten and Muscarello, Vincenzo and Marzocca, Pier},
  title     = {About the wing and whirl flutter of a slender wing-propeller system},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C037542},
  pages     = {1 -- 14},
  year      = {2024},
  abstract  = {Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan (distributed electric propulsion), leading to highly flexible dynamic systems that can exhibit aeroelastic instabilities. This paper introduces a validated methodology to investigate the aeroelastic instabilities of wing-propeller systems and to understand the dynamic mechanism leading to wing and whirl flutter and transition from one to the other. Factors such as nacelle positions along the wing span and chord and its propulsion system mounting stiffness are considered. Additionally, preliminary design guidelines are proposed for flutter-free wing-propeller systems applicable to novel aircraft designs. The study demonstrates how the critical speed of the wing-propeller systems is influenced by the mounting stiffness and propeller position. Weak mounting stiffnesses result in whirl flutter, while hard mounting stiffnesses lead to wing flutter. For the latter, the position of the propeller along the wing span may change the wing mode shapes and thus the flutter mechanism. Propeller positions closer to the wing tip enhance stability, but pusher configurations are more critical due to the mass distribution behind the elastic axis.},
  language  = {en}
}
@inproceedings{ThomaStiemerBraunetal.2023,
  author    = {Thoma, Andreas and Stiemer, Luc and Braun, Carsten and Fisher, Alex and Gardi, Alessandro G.},
  title     = {Potential of hybrid neural network local path planner for small UAV in urban environments},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2023-2359},
  pages     = {13 Seiten},
  year      = {2023},
  abstract  = {This work proposes a hybrid algorithm combining an Artificial Neural Network (ANN) with a conventional local path planner to navigate UAVs efficiently in various unknown urban environments. The proposed method of a Hybrid Artificial Neural Network Avoidance System is called HANNAS. The ANN analyses a video stream and classifies the current environment. This information about the current Environment is used to set several control parameters of a conventional local path planner, the 3DVFH*. The local path planner then plans the path toward a specific goal point based on distance data from a depth camera. We trained and tested a state-of-the-art image segmentation algorithm, PP-LiteSeg. The proposed HANNAS method reaches a failure probability of 17\%, which is less than half the failure probability of the baseline and around half the failure probability of an improved, bio-inspired version of the 3DVFH*. The proposed HANNAS method does not show any disadvantages regarding flight time or flight distance.},
  language  = {en}
}
@incollection{ReimerBraunWellmeretal.2010,
  author    = {Reimer, Lars and Braun, Carsten and Wellmer, Georg and Behr, Marek and Ballmann, Josef},
  title     = {Development of a modular method for computational aero-structural analysis of aircraft},
  series = {Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schr{\"o}der. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109},
  booktitle = {Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schr{\"o}der. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-642-04087-0},
  pages     = {205 -- 238},
  year      = {2010},
  language  = {en}
}
@inproceedings{BergmannGraebenerWildetal.2019,
  author    = {Bergmann, Kevin and Gr{\"a}bener, Josefine and Wild, Dominik and Ulfers, H. and Czupalla, Markus},
  title     = {Study on thermal stabilization of a GEO-stationary telescope baffling system by integral application of phase change material},
  series = {International Conference on Environmental Systems},
  booktitle = {International Conference on Environmental Systems},
  pages     = {1 -- 14},
  year      = {2019},
  abstract  = {The utilization of phase change material (PCM) for latent heat storage and thermal control of spacecraft has been demonstrated in the past in few missions only. One limiting factor was the fact that all concepts developed so far envisioned the PCM to be applied as an additional capacitor, encapsulated in its own housing, leading to mass, efficiency and accommodation challenges. Recently, the application of PCM within the scan cavity of a GEOS type satellite has been suggested, in order to tackle thermal issues due to direct sun intrusion (Choi, M., 2014). However, the application of PCM in such complex mechanical structures is extremely challenging. A new concept to tackle this issue is currently under development at the FH Aachen University of Applied Sciences. The concept "Infused Thermal Solutions (ITS)" is based on the idea to 3D print metallic structures in their regular functional shape, but double walled with internal lattice support structures, allowing the infusion of a PCM layer directly into the voids and eliminating the need for additional parts and interfaces. Together with OHB System, FH Aachen theoretically studied the application of this technology to the Meteosat Third Generation (MTG) Infra-Red Sounder (IRS) instrument. The study focuses on the scan cavity and entrance baffling assembly (EBA) of the IRS. It consists of thermal analyses, 3D-redesign and bread boarding of a scaled and PCM infused EBA version. In the thermal design of the alternative EBA, PCM was applied directly into the EBA, simulating the worst hot case sun intrusion of the mission. By applying 4kg of PCM (to a 60kg baffle) the EBA temperature excursions during sun intrusion were limited from 140K to 30K, leading to a significant thermo-opto-elastic performance gain. This paper introduces the ITS concept development status.},
  language  = {en}
}
@article{UlmerBraunChengetal.2023,
  author    = {Ulmer, Jessica and Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {A human factors-aware assistance system in manufacturing based on gamification and hardware modularisation},
  series = {International Journal of Production Research},
  journal   = {International Journal of Production Research},
  publisher = {Taylor \& Francis},
  issn      = {0020-7543 (Print)},
  doi       = {10.1080/00207543.2023.2166140},
  year      = {2023},
  abstract  = {Assistance systems have been widely adopted in the manufacturing sector to facilitate various processes and tasks in production environments. However, existing systems are mostly equipped with rigid functional logic and do not provide individual user experiences or adapt to their capabilities. This work integrates human factors in assistance systems by adjusting the hardware and instruction presented to the workers' cognitive and physical demands. A modular system architecture is designed accordingly, which allows a flexible component exchange according to the user and the work task. Gamification, the use of game elements in non-gaming contexts, has been further adopted in this work to provide level-based instructions and personalised feedback. The developed framework is validated by applying it to a manual workstation for industrial assembly routines.},
  language  = {en}
}
@article{FiedlerOrzadaFloeseretal.2021,
  author    = {Fiedler, Thomas M. and Orzada, Stephan and Fl{\"o}ser, Martina and Rietsch, Stefan H. G. and Quick, Harald H. and Ladd, Mark E. and Bitz, Andreas},
  title     = {Performance analysis of integrated RF microstrip transmit antenna arrays with high channel count for body imaging at 7 T},
  series = {NMR in Biomedicine},
  volume    = {34},
  journal   = {NMR in Biomedicine},
  number    = {7},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {0952-3480 (ISSN)},
  doi       = {10.1002/nbm.4515},
  pages     = {18 SeitenWiley},
  year      = {2021},
  abstract  = {The aim of the current study was to investigate the performance of integrated RF transmit arrays with high channel count consisting of meander microstrip antennas for body imaging at 7 T and to optimize the position and number of transmit ele- ments. RF simulations using multiring antenna arrays placed behind the bore liner were performed for realistic exposure conditions for body imaging. Simulations were performed for arrays with as few as eight elements and for arrays with high channel counts of up to 48 elements. The B1+ field was evaluated regarding the degrees of freedom for RF shimming in the abdomen. Worst-case specific absorption rate (SARwc ), SAR overestimation in the matrix compression, the number of virtual obser- vation points (VOPs) and SAR efficiency were evaluated. Constrained RF shimming was performed in differently oriented regions of interest in the body, and the devia- tion from a target B1+ field was evaluated. Results show that integrated multiring arrays are able to generate homogeneous B1+ field distributions for large FOVs, espe- cially for coronal/sagittal slices, and thus enable body imaging at 7 T with a clinical workflow; however, a low duty cycle or a high SAR is required to achieve homoge- neous B1+ distributions and to exploit the full potential. In conclusion, integrated arrays allow for high element counts that have high degrees of freedom for the pulse optimization but also produce high SARwc , which reduces the SAR accuracy in the VOP compression for low-SAR protocols, leading to a potential reduction in array performance. Smaller SAR overestimations can increase SAR accuracy, but lead to a high number of VOPs, which increases the computational cost for VOP evaluation and makes online SAR monitoring or pulse optimization challenging. Arrays with interleaved rings showed the best results in the study.},
  language  = {en}
}
@article{ChwallekNawrathKrastinaetal.2024,
  author    = {Chwallek, Constanze and Nawrath, Lara and Krastina, Anzelika and Bruksle, Ieva},
  title     = {Supportive research on sustainable entrepreneurship and business practices},
  series = {SECA Sustainable Entrepreneurship for Climate Action},
  journal   = {SECA Sustainable Entrepreneurship for Climate Action},
  number    = {3},
  publisher = {Lapland University of Applied Sciences Ltd},
  address   = {Rovaniemi},
  isbn      = {978-952-316-514-4 (pdf)},
  issn      = {2954-1654 (on-line publication)},
  pages     = {67 Seiten},
  year      = {2024},
  language  = {en}
}
@article{WildSchrezenmeierCzupallaetal.2020,
  author    = {Wild, Dominik and Schrezenmeier, Johannes and Czupalla, Markus and F{\"o}rstner, Roger},
  title     = {Thermal Characterization of additive manufactured Integral Structures for Phase Change Applications},
  series = {2020 International Conference on Environmental Systems},
  journal   = {2020 International Conference on Environmental Systems},
  publisher = {Texas Tech University},
  year      = {2020},
  abstract  = {"Infused Thermal Solutions" (ITS) introduces a method for passive thermal control to stabilize structural components thermally without active heating and cooling systems, by using phase change material (PCM) in combination with lattice - both embedded into an additive manufactured integral structure. The technology is currently under development. This paper presents the results of the thermal property measurements performed on additive manufactured ITS breadboards. Within the breadboard campaigns key characteristics of the additive manufactured specimens were derived: Mechanical parameters: specimen impermeability, minimum wall thickness, lattice structure, subsequent heat treatment. Thermal properties: thermo-optical surface properties of the additive manufactured raw material, thermal conductivity and specific heat capacity measurements. As a conclusion the paper introduces an overview of potential ITS hardware applications, expected to increase the thermal performance.},
  language  = {en}
}
@article{SchopenNarayanBeckmannetal.2024,
  author    = {Schopen, Oliver and Narayan, Sriram and Beckmann, Marvin and Najmi, Aezid-Ul-Hassan and Esch, Thomas and Shabani, Bahman},
  title     = {An EIS approach to quantify the effects of inlet air relative humidity on the performance of proton exchange membrane fuel cells: a pathway to developing a novel fault diagnostic method},
  series = {International Journal of Hydrogen Energy},
  volume    = {58},
  journal   = {International Journal of Hydrogen Energy},
  number    = {8},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0360-3199 (print)},
  issn      = {1879-3487 (online)},
  doi       = {10.1016/j.ijhydene.2024.01.218},
  pages     = {1302 -- 1315},
  year      = {2024},
  abstract  = {In this work, the effect of low air relative humidity on the operation of a polymer electrolyte membrane fuel cell is investigated. An innovative method through performing in situ electrochemical impedance spectroscopy is utilised to quantify the effect of inlet air relative humidity at the cathode side on internal ionic resistances and output voltage of the fuel cell. In addition, algorithms are developed to analyse the electrochemical characteristics of the fuel cell. For the specific fuel cell stack used in this study, the membrane resistance drops by over 39 \% and the cathode side charge transfer resistance decreases by 23 \% after increasing the humidity from 30 \% to 85 \%, while the results of static operation also show an increase of ∼2.2 \% in the voltage output after increasing the relative humidity from 30 \% to 85 \%. In dynamic operation, visible drying effects occur at < 50 \% relative humidity, whereby the increase of the air side stoichiometry increases the drying effects. Furthermore, other parameters, such as hydrogen humidification, internal stack structure, and operating parameters like stoichiometry, pressure, and temperature affect the overall water balance. Therefore, the optimal humidification range must be determined by considering all these parameters to maximise the fuel cell performance and durability. The results of this study are used to develop a health management system to ensure sufficient humidification by continuously monitoring the fuel cell polarisation data and electrochemical impedance spectroscopy indicators.},
  language  = {en}
}
@inproceedings{StarkRiepingEsch2023,
  author    = {Stark, Ralf and Rieping, Carla and Esch, Thomas},
  title     = {The impact of guide tubes on flow separation in rocket nozzles},
  series = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  booktitle = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  pages     = {8 Seiten},
  year      = {2023},
  abstract  = {Rocket engine test facilities and launch pads are typically equipped with a guide tube. Its purpose is to ensure the controlled and safe routing of the hot exhaust gases. In addition, the guide tube induces a suction that effects the nozzle flow, namely the flow separation during transient start-up and shut-down of the engine. A cold flow subscale nozzle in combination with a set of guide tubes was studied experimentally to determine the main influencing parameters.},
  language  = {en}
}
@inproceedings{StarkBartelDitscheetal.2023,
  author    = {Stark, Ralf and Bartel, Sebastian and Ditsche, Florian and Esch, Thomas},
  title     = {Design study of a 30kN LOX/LCH4 aerospike rocket engine for lunar lander application},
  series = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  booktitle = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS},
  pages     = {9 Seiten},
  year      = {2023},
  abstract  = {Based on lunar lander concept EL3, various LOX/CH4 aerospike engines were studied. A distinction was made between single and cluster configurations as well as ideal and non-ideal contour concepts. It could be shown that non-ideal aerospike engines promise a significant payload gain.},
  language  = {en}
}
@misc{BiewendtBlaschkeBoehnert2019,
  author    = {Biewendt, Marcel and Blaschke, Florian and B{\"o}hnert, Arno},
  title     = {The rebound effect: a critical and systematic review on the current state of affairs},
  series = {Abstracts of the International Conference on Sustainable Economy and Agriculture},
  journal   = {Abstracts of the International Conference on Sustainable Economy and Agriculture},
  editor    = {Koponicsne Gy{\"o}rke, Diana},
  publisher = {Universit{\"a}t Kaposv{\´a}r},
  address   = {Kaposv{\´a}r},
  isbn      = {978-615-5599-72-9},
  pages     = {101 -- 101},
  year      = {2019},
  language  = {en}
}
@article{UysalCreutzFiratetal.2022,
  author    = {Uysal, Karya and Creutz, Till and Firat, Ipek Seda and Artmann, Gerhard and Teusch, Nicole and Temiz Artmann, Ayseg{\"u}l},
  title     = {Bio-functionalized ultra-thin, large-area and waterproof silicone membranes for biomechanical cellular loading and compliance experiments},
  series = {Polymers},
  volume    = {14},
  journal   = {Polymers},
  number    = {11},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2073-4360},
  pages     = {2213},
  year      = {2022},
  abstract  = {Biocompatibility, flexibility and durability make polydimethylsiloxane (PDMS) membranes top candidates in biomedical applications. CellDrum technology uses large area, <10 µm thin membranes as mechanical stress sensors of thin cell layers. For this to be successful, the properties (thickness, temperature, dust, wrinkles, etc.) must be precisely controlled. The following parameters of membrane fabrication by means of the Floating-on-Water (FoW) method were investigated: (1) PDMS volume, (2) ambient temperature, (3) membrane deflection and (4) membrane mechanical compliance. Significant differences were found between all PDMS volumes and thicknesses tested (p < 0.01). They also differed from the calculated values. At room temperatures between 22 and 26 °C, significant differences in average thickness values were found, as well as a continuous decrease in thicknesses within a 4 °C temperature elevation. No correlation was found between the membrane thickness groups (between 3-4 µm) in terms of deflection and compliance. We successfully present a fabrication method for thin bio-functionalized membranes in conjunction with a four-step quality management system. The results highlight the importance of tight regulation of production parameters through quality control. The use of membranes described here could also become the basis for material testing on thin, viscous layers such as polymers, dyes and adhesives, which goes far beyond biological applications.},
  language  = {en}
}
@article{TemizArtmannKurulgandemirciFıratetal.2021,
  author    = {Temiz Artmann, Ayseg{\"u}l and Kurulgan demirci, Eylem and F{\i}rat, Ipek Seda and Oflaz, Hakan and Artmann, Gerhard},
  title     = {Recombinant activated protein C (rhAPC) affects lipopolysaccharide-induced mechanical compliance changes and beat frequency of mESC-derived cardiomyocyte monolayers},
  series = {SHOCK},
  journal   = {SHOCK},
  publisher = {Wolters Kluwer},
  address   = {K{\"o}ln},
  issn      = {1540-0514},
  doi       = {10.1097/SHK.0000000000001845},
  year      = {2021},
  language  = {en}
}
@article{KowalewskiBragardHueningetal.2023,
  author    = {Kowalewski, Paul and Bragard, Michael and H{\"u}ning, Felix and De Doncker, Rik W.},
  title     = {An inexpensive Wiegand-sensor-based rotary encoder without rotating magnets for use in electrical drives},
  series = {IEEE Transactions on Instrumentation and Measurement},
  volume    = {72},
  journal   = {IEEE Transactions on Instrumentation and Measurement},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0018-9456 (Print)},
  doi       = {10.1109/TIM.2023.3326166},
  pages     = {10 Seiten},
  year      = {2023},
  abstract  = {This paper introduces an inexpensive Wiegand-sensor-based rotary encoder that avoids rotating magnets and is suitable for electrical-drive applications. So far, Wiegand-sensor-based encoders usually include a magnetic pole wheel with rotating permanent magnets. These encoders combine the disadvantages of an increased magnet demand and a limited maximal speed due to the centripetal force acting on the rotating magnets. The proposed approach reduces the total demand of permanent magnets drastically. Moreover, the rotating part is manufacturable from a single piece of steel, which makes it very robust and cheap. This work presents the theoretical operating principle of the proposed approach and validates its benefits on a hardware prototype. The presented proof-of-concept prototype achieves a mechanical resolution of 4.5 ° by using only 4 permanent magnets, 2Wiegand sensors and a rotating steel gear wheel with 20 teeth.},
  language  = {en}
}
@article{SeifarthGrosseGrossmannetal.2017,
  author    = {Seifarth, Volker and Grosse, Joachim O. and Grossmann, Matthias and Janke, Heinz Peter and Arndt, Patrick and Koch, Sabine and Epple, Matthias and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Mechanical induction of bi-directional orientation of primary porcine bladder smooth muscle cells in tubular fibrin-poly(vinylidene fluoride) scaffolds for ureteral and urethral repair using cyclic and focal balloon catheter stimulation},
  series = {Journal of Biomaterials Applications},
  volume    = {32},
  journal   = {Journal of Biomaterials Applications},
  number    = {3},
  publisher = {Sage},
  address   = {London},
  issn      = {1530-8022},
  doi       = {10.1177/0885328217723178},
  pages     = {321 -- 330},
  year      = {2017},
  language  = {en}
}
@article{SeifarthGossmannGrosseetal.2015,
  author    = {Seifarth, Volker and Goßmann, Matthias and Grosse, J. O. and Becker, C. and Heschel, I. and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Development of a Bioreactor to Culture Tissue Engineered Ureters Based on the Application of Tubular OPTIMAIX 3D Scaffolds},
  series = {Urologia Internationalis},
  volume    = {2015},
  journal   = {Urologia Internationalis},
  number    = {95},
  publisher = {Karger},
  address   = {Basel},
  issn      = {0042-1138},
  doi       = {10.1159/000368419},
  pages     = {106 -- 113},
  year      = {2015},
  language  = {en}
}
@article{Alexopoulos2012,
  author    = {Alexopoulos, Spiros},
  title     = {Biogas systems: basics, biogas multifunction, principle of fermentation and hybrid application with a solar tower for the treatment of waste animal manure},
  series = {Journal of Engineering Science and Technology Review},
  volume    = {5},
  journal   = {Journal of Engineering Science and Technology Review},
  number    = {4},
  issn      = {1791-2377},
  pages     = {48 -- 55},
  year      = {2012},
  abstract  = {Two of the main environmental problems of today's society are the continuously increasing production of organic wastes as well as the increase of carbon dioxide in the atmosphere and the related green house effect. A way to solve these problems is the production of biogas. Biogas is a combustible gas consisting of methane, carbon dioxide and small amounts of other gases and trace elements. Production of biogas through anaerobic digestion of animal manure and slurries as well as of a wide range of digestible organic wastes and agricultural residues, converts these substrates into electricity and heat and offers a natural fertiliser for agriculture. The microbiological process of decomposition of organic matter, in the absence of oxygen takes place in reactors, called digesters. Biogas can be used as a fuel in a gas turbine or burner and can be used in a hybrid solar tower system offering a solution for waste treatment of agricultural and animal residues. A solar tower system consists of a heliostat field, which concentrates direct solar irradiation on an open volumetric central receiver. The receiver heats up ambient air to temperatures of around 700°C. The hot air's heat energy is transferred to a steam Rankine cycle in a heat recovery steam generator (HRSG). The steam drives a steam turbine, which in turn drives a generator for producing electricity. In order to increase the operational hours of a solar tower power plant, a heat storage system and/ or hybridization may be considered. The advantage of solar-fossil hybrid power plants, compared to solar-only systems, lies in low additional investment costs due to an adaptable solar share and reduced technical and economical risks. On sunny days the hybrid system operates in a solar-only mode with the central receiver and on cloudy days and at night with the gas turbine only. As an alternative to methane gas, environmentally neutral biogas can be used for operating the gas turbine. Hence, the hybrid system is operated to 100\% from renewable energy sources},
  language  = {en}
}
@inproceedings{ElMoussaouiKassmiAlexopoulosetal.2021,
  author    = {El Moussaoui, Noureddine and Kassmi, Khalil and Alexopoulos, Spiros and Schwarzer, Klemens and Chayeb, Hamid and Bachiri, Najib},
  title     = {Simulation studies on a new innovative design of a hybrid solar distiller MSDH alimented with a thermal and photovoltaic energy},
  series = {Materialstoday: Proceedings},
  volume    = {45},
  booktitle = {Materialstoday: Proceedings},
  number    = {8},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2214-7853},
  doi       = {10.1016/j.matpr.2021.03.115},
  pages     = {7653 -- 7660},
  year      = {2021},
  abstract  = {In this paper, we present the structure, the simulation the operation of a multi-stage, hybrid solar desalination system (MSDH), powered by thermal and photovoltaic (PV) (MSDH) energy. The MSDH system consists of a lower basin, eight horizontal stages, a field of four flat thermal collectors with a total area of 8.4 m2, 3 Kw PV panels and solar batteries. During the day the system is heated by thermal energy, and at night by heating resistors, powered by solar batteries. These batteries are charged by the photovoltaic panels during the day. More specifically, during the day and at night, we analyse the temperature of the stages and the production of distilled water according to the solar irradiation intensity and the electric heating power, supplied by the solar batteries. The simulations were carried out in the meteorological conditions of the winter month (February 2020), presenting intensities of irradiance and ambient temperature reaching 824 W/m2 and 23 °C respectively. The results obtained show that during the day the system is heated by the thermal collectors, the temperature of the stages and the quantity of water produced reach 80 °C and 30 Kg respectively. At night, from 6p.m. the system is heated by the electric energy stored in the batteries, the temperature of the stages and the quantity of water produced reach respectively 90 °C and 104 Kg for an electric heating power of 2 Kw. Moreover, when the electric power varies from 1 Kw to 3 Kw the quantity of water produced varies from 92 Kg to 134 Kg. The analysis of these results and their comparison with conventional solar thermal desalination systems shows a clear improvement both in the heating of the stages, by 10\%, and in the quantity of water produced by a factor of 3.},
  language  = {en}
}
@article{BialonskiCaronSchloenetal.2016,
  author    = {Bialonski, Stephan and Caron, David A. and Schloen, Julia and Feudel, Ulrike and Kantz, Holger and Moorthi, Stefanie D.},
  title     = {Phytoplankton dynamics in the Southern California Bight indicate a complex mixture of transport and biology},
  series = {Journal of Plankton Research},
  volume    = {38},
  journal   = {Journal of Plankton Research},
  number    = {4},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1464-3774},
  doi       = {10.1093/plankt/fbv122},
  pages     = {1077 -- 1091},
  year      = {2016},
  abstract  = {The stimulation and dominance of potentially harmful phytoplankton taxa at a given locale and time are determined by local environmental conditions as well as by transport to or from neighboring regions. The present study investigated the occurrence of common harmful algal bloom (HAB) taxa within the Southern California Bight, using cross-correlation functions to determine potential dependencies between HAB taxa and environmental factors, and potential links to algal transport via local hydrography and currents. A simulation study, in which Lagrangian particles were released, was used to assess travel times due to advection by prevailing ocean currents in the bight. Our results indicate that transport of some taxa may be an important mechanism for the expansion of their distributions into other regions, which was supported by mean travel times derived from our simulation study and other literature on ocean currents in the Southern California Bight. In other cases, however, phytoplankton dynamics were rather linked to local environmental conditions, including coastal upwelling events. Overall, our study shows that complex current patterns in the Southern California Bight may contribute significantly to the formation and expansion of HABs in addition to local environmental factors determining the spatiotemporal dynamics of phytoplankton blooms.},
  language  = {en}
}
@incollection{BrittenBraunHesseetal.2003,
  author    = {Britten, G. and Braun, Carsten and Hesse, M. and Ballmann, Josef},
  title     = {Computational aeroelasticity with reduced structural models},
  series = {Flow modulation and fluid-structure interaction at airplane wings : research results of the Collaborative Research Center SFB 401 at RWTH Aachen, University of Technology, Aachen, Germany / Josef Ballmann (Ed.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 84},
  booktitle = {Flow modulation and fluid-structure interaction at airplane wings : research results of the Collaborative Research Center SFB 401 at RWTH Aachen, University of Technology, Aachen, Germany / Josef Ballmann (Ed.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 84},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {3-540-40209-8},
  pages     = {275 -- 299},
  year      = {2003},
  language  = {en}
}
@article{AlexopoulosBreitbachHoffschmidtetal.2008,
  author    = {Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Stobbe, P.},
  title     = {Computational fluid flow of porous resic ceramic filtering modules and optimization of the channel edge form geometry},
  series = {Proceedings : April 14 - 18, 2008, Leipzig, Germany / hosted by VDI, Society for Chemical and Process Engineering . Vol 2},
  journal   = {Proceedings : April 14 - 18, 2008, Leipzig, Germany / hosted by VDI, Society for Chemical and Process Engineering . Vol 2},
  publisher = {Filtech Exhibitions},
  address   = {Meerbusch},
  pages     = {300 -- 304},
  year      = {2008},
  language  = {en}
}
@article{RaffeisAdjeiKyeremehVroomenetal.2020,
  author    = {Raffeis, Iris and Adjei-Kyeremeh, Frank and Vroomen, Uwe and Westhoff, Elmar and Bremen, Sebastian and Hohoi, Alexandru and B{\"u}hrig-Polaczek, Andreas},
  title     = {Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties},
  series = {Applied Sciences},
  volume    = {10},
  journal   = {Applied Sciences},
  number    = {Art. 3401},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app10103401},
  pages     = {1 -- 15},
  year      = {2020},
  abstract  = {As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni-Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8\% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s-1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20\% to 31\% (V), as well as from 16\% to 25\% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.},
  language  = {en}
}
@inproceedings{WalterElsenMuelleretal.1999,
  author    = {Walter, Peter and Elsen, Ingo and M{\"u}ller, Holger and Kraiss, Karl-Friedrich},
  title     = {3D object recognition with a specialized mixtures of experts architecture},
  series = {IJCNN'99. International Joint Conference on Neural Networks. Proceedings},
  booktitle = {IJCNN'99. International Joint Conference on Neural Networks. Proceedings},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {0-7803-5529-6},
  issn      = {1098-7576},
  doi       = {10.1109/IJCNN.1999.836243},
  pages     = {3563 -- 3568},
  year      = {1999},
  abstract  = {Aim of the AXON2 project (Adaptive Expert System for Object Recogniton using Neuml Networks) is the development of an object recognition system (ORS) capable of recognizing isolated 3d objects from arbitrary views. Commonly, classification is based on a single feature extracted from the original image. Here we present an architecture adapted from the Mixtures of Eaqerts algorithm which uses multiple neuml networks to integmte different features. During tmining each neural network specializes in a subset of objects or object views appropriate to the properties of the corresponding feature space. In recognition mode the system dynamically chooses the most relevant features and combines them with maximum eficiency. The remaining less relevant features arz not computed and do therefore not decelerate the-recognition process. Thus, the algorithm is well suited for ml-time applications.},
  language  = {en}
}
@article{ElsenKraiss1999,
  author    = {Elsen, Ingo and Kraiss, Karl-Friedrich},
  title     = {System concept and realization of a scalable neurocomputing architecture},
  series = {Systems Analysis Modelling Simulation},
  volume    = {35},
  journal   = {Systems Analysis Modelling Simulation},
  number    = {4},
  publisher = {Gordon and Breach Science Publishers},
  address   = {Amsterdam},
  issn      = {0232-9298},
  pages     = {399 -- 419},
  year      = {1999},
  abstract  = {This paper describes the realization of a novel neurocomputer which is based on the concepts of a coprocessor. In contrast to existing neurocomputers the main interest was the realization of a scalable, flexible system, which is capable of computing neural networks of arbitrary topology and scale, with full independence of special hardware from the software's point of view. On the other hand, computational power should be added, whenever needed and flexibly adapted to the requirements of the application. Hardware independence is achieved by a run time system which is capable of using all available computing power, including multiple host CPUs and an arbitrary number of neural coprocessors autonomously. The realization of arbitrary neural topologies is provided through the implementation of the elementary operations which can be found in most neural topologies.},
  language  = {en}
}
@article{ElsenKraissKrumbiegeletal.1999,
  author    = {Elsen, Ingo and Kraiss, Karl-Friedrich and Krumbiegel, Dirk and Walter, Peter and Wickel, Jochen},
  title     = {Visual information retrieval for 3D product identification: a midterm report},
  series = {KI - K{\"u}nstliche Intelligenz},
  volume    = {13},
  journal   = {KI - K{\"u}nstliche Intelligenz},
  number    = {1},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1610-1987},
  pages     = {64 -- 67},
  year      = {1999},
  language  = {en}
}
@inproceedings{Elsen1998,
  author    = {Elsen, Ingo},
  title     = {A pixel based approach to view based object recognition with self-organizing neural networks},
  series = {IECON'98. Proceedings of the 24th Annual Conference of the IEEE Industrial Electronics Society},
  booktitle = {IECON'98. Proceedings of the 24th Annual Conference of the IEEE Industrial Electronics Society},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {0-7803-4503-7},
  doi       = {10.1109/IECON.1998.724032},
  pages     = {2040 -- 2044},
  year      = {1998},
  abstract  = {This paper addresses the pixel based classification of three dimensional objects from arbitrary views. To perform this task a coding strategy, inspired by the biological model of human vision, for pixel data is described. The coding strategy ensures that the input data is invariant against shift, scale and rotation of the object in the input domain. The image data is used as input to a class of self organizing neural networks, the Kohonen-maps or self-organizing feature maps (SOFM). To verify this approach two test sets have been generated: the first set, consisting of artificially generated images, is used to examine the classification properties of the SOFMs; the second test set examines the clustering capabilities of the SOFM when real world image data is applied to the network after it has been preprocessed to be invariant against shift, scale and rotation. It is shown that the clustering capability of the SOFM is strongly dependant on the invariance coding of the images.},
  language  = {en}
}
@inproceedings{ElsenKraissKrumbiegel1997,
  author    = {Elsen, Ingo and Kraiss, Karl-Friedrich and Krumbiegel, Dirk},
  title     = {Pixel based 3D object recognition with bidirectional associative memories},
  series = {International Conference on Neural Networks 1997},
  booktitle = {International Conference on Neural Networks 1997},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {0-7803-4122-8},
  pages     = {1679 -- 1684},
  year      = {1997},
  abstract  = {This paper addresses the pixel based recognition of 3D objects with bidirectional associative memories. Computational power and memory requirements for this approach are identified and compared to the performance of current computer architectures by benchmarking different processors. It is shown, that the performance of special purpose hardware, like neurocomputers, is between one and two orders of magnitude higher than the performance of mainstream hardware. On the other hand, the calculation of small neural networks is performed more efficiently on mainstream processors. Based on these results a novel concept is developed, which is tailored for the efficient calculation of bidirectional associative memories. The computational efficiency is further enhanced by the application of algorithms and storage techniques which are matched to characteristics of the application at hand.},
  language  = {en}
}
@article{DickhoffHorikawaFunke2021,
  author    = {Dickhoff, Jens and Horikawa, Atsushi and Funke, Harald},
  title     = {Hydrogen Combustion - new DLE Combustor Addresses NOx Emissions and Flashback},
  series = {Turbomachinery international : the global journal of energy equipment},
  volume    = {62},
  journal   = {Turbomachinery international : the global journal of energy equipment},
  number    = {4},
  publisher = {MJH Life Sciences},
  address   = {Cranbury},
  issn      = {2767-2328},
  pages     = {26 -- 27},
  year      = {2021},
  language  = {en}
}
@article{Gaigall2023,
  author    = {Gaigall, Daniel},
  title     = {Allocating and forecasting changes in risk},
  series = {Journal of risk},
  volume    = {25},
  journal   = {Journal of risk},
  number    = {3},
  editor    = {AitSahlia, Farid},
  publisher = {Infopro Digital Risk},
  address   = {London},
  issn      = {1755-2842},
  doi       = {10.21314/JOR.2022.048},
  pages     = {1 -- 24},
  year      = {2023},
  abstract  = {We consider time-dependent portfolios and discuss the allocation of changes in the risk of a portfolio to changes in the portfolio's components. For this purpose we adopt established allocation principles. We also use our approach to obtain forecasts for changes in the risk of the portfolio's components. To put the approach into practice we present an implementation based on the output of a simulation. Allocation is illustrated with an example portfolio in the context of Solvency II. The quality of the forecasts is investigated with an empirical study.},
  language  = {en}
}
@article{Gaigall2023,
  author    = {Gaigall, Daniel},
  title     = {On the applicability of several tests to models with not identically distributed random effects},
  series = {Statistics : A Journal of Theoretical and Applied Statistics},
  volume    = {57},
  journal   = {Statistics : A Journal of Theoretical and Applied Statistics},
  publisher = {Taylor \& Francis},
  address   = {London},
  isbn      = {0323-3944},
  issn      = {1029-4910},
  doi       = {10.1080/02331888.2023.2193748},
  pages     = {14 Seiten},
  year      = {2023},
  abstract  = {We consider Kolmogorov-Smirnov and Cram{\´e}r-von-Mises type tests for testing central symmetry, exchangeability, and independence. In the standard case, the tests are intended for the application to independent and identically distributed data with unknown distribution. The tests are available for multivariate data and bootstrap procedures are suitable to obtain critical values. We discuss the applicability of the tests to random effects models, where the random effects are independent but not necessarily identically distributed and with possibly unknown distributions. Theoretical results show the adequacy of the tests in this situation. The quality of the tests in models with random effects is investigated by simulations. Empirical results obtained confirm the theoretical findings. A real data example illustrates the application.},
  language  = {en}
}