@inproceedings{LangWirtzHeitzeretal.1999,
  author    = {Lang, H. and Wirtz, K. and Heitzer, Michael and Staat, Manfred and Oettel, R.},
  title     = {Zyklische Einspielversuche zur Verifikation von Shakedown-Analysen mittels FEM},
  year      = {1999},
  abstract  = {Im Rahmen von Erm{\"u}dungsanalysen ist nachzuweisen, daß die thermisch bedingten fortschreitenden Deformationen begrenzt bleiben. Hierzu ist die Abgrenzung des Shakedown-Bereiches (Einspielen) vom Ratchetting-Bereich (fortschreitende Deformation) von Interesse. Im Rahmen eines EU-gef{\"o}rderten Forschungsvorhabens wurden Experimente mit einem 4-Stab-Modell durchgef{\"u}hrt. Das Experiment bestand aus einem wassergek{\"u}hlten inneren Rohr und drei isolierten und beheizbaren {\"a}ußeren Probest{\"a}ben. Das System wurde durch alternierende Axialkr{\"a}fte, denen alternierende Temperaturen an den {\"a}ußeren St{\"a}ben {\"u}berlagert wurden, belastet. Die Versuchsparameter wurden teilweise nach vorausgegangenen Einspielanalysen gew{\"a}hlt. W{\"a}hrend der Versuchsdurchf{\"u}hrung wurden Temperaturen und Dehnungen zeitabh{\"a}ngig gemessen. Begleitend und nachfolgend zur Versuchsdurchf{\"u}hrung wurden die Belastungen und die daraus resultierenden Beanspruchungen nachvollzogen. Bei dieser inkrementellen elasto-plastischen Analyse mit dem Programm ANSYS wurden unterschiedliche Werkstoffmodelle angesetzt. Die Ergebnisse dieser Simulationsberechnung dienen dazu, die Shakedown-Analysen mittels FE-Methode zu verifizieren.},
  subject      = {Einspielen <Werkstoff>},
  language  = {de}
}
@inproceedings{KoplinSiemonsOcenValentinetal.2006,
  author    = {Koplin, Tobias J. and Siemons, Maike and Oc{\´e}n-Val{\´e}ntin, C{\´e}sar and Sanders, Daniel and Simon, Ulrich},
  title     = {Workflow for high throughput screening of gas sensing materials},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1407},
  year      = {2006},
  abstract  = {The workflow of a high throughput screening setup for the rapid identification of new and improved sensor materials is presented. The polyol method was applied to prepare nanoparticular metal oxides as base materials, which were functionalised by surface doping. Using multi-electrode substrates and high throughput impedance spectroscopy (HT-IS) a wide range of materials could be screened in a short time. Applying HT-IS in search of new selective gas sensing materials a NO2-tolerant NO sensing material with reduced sensitivities towards other test gases was identified based on iridium doped zinc oxide. Analogous behaviour was observed for iridium doped indium oxide.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{MuellerVeggianHaenniBeuscheretal.1980,
  author    = {M{\"u}ller-Veggian, Mattea and Haenni, D. R. and Beuscher, H. and Lieder, R. M.},
  title     = {Weak coupling of a neutron hole to a ¹⁴⁶ Gd core ; an in-beam study of ¹⁴⁵ Gd},
  series = {Structure of medium-heavy nuclei, 1979 : proceedings of the 6. European Physical Soc. Nuclear Divisional Conference on the Structure of Medium-Heavy Nuclei held in Rhodes, Greece, 1-4 May 1979 / ed. Committee: G. S. Anagnostatos ... - (Conference series / Institute of Physics London, Bristol ; 49)},
  booktitle = {Structure of medium-heavy nuclei, 1979 : proceedings of the 6. European Physical Soc. Nuclear Divisional Conference on the Structure of Medium-Heavy Nuclei held in Rhodes, Greece, 1-4 May 1979 / ed. Committee: G. S. Anagnostatos ... - (Conference series / Institute of Physics London, Bristol ; 49)},
  publisher = {Inst. of Physics},
  address   = {Bristol},
  isbn      = {0-85498-140-3},
  pages     = {133},
  year      = {1980},
  language  = {en}
}
@inproceedings{ArinkinDigel2009,
  author    = {Arinkin, Vladimir and Digel, Ilya},
  title     = {Water bridge phenomenon : [abstract]},
  year      = {2009},
  abstract  = {One of interesting but not well known water properties is related to appearance of highly ordered structures in response to strong electrical field. In 1893 Sir William Armstrong placed a cotton thread between two wine glasses filled with chemically pure water. When high DC voltage was applied between the glasses, a connection consisting of water formed, producing a "water bridge"},
  subject      = {Hydrodynamik},
  language  = {en}
}
@inproceedings{KraftZoell2014,
  author    = {Kraft, Bodo and Z{\"o}ll, Axel},
  title     = {Von der Langstrecke zum Sprint - Agile Methoden in traditionellen Unternehmen},
  series = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung},
  booktitle = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung},
  editor    = {Engstler, Martin},
  publisher = {Gesellschaft f{\"u}r Informatik},
  address   = {Bonn},
  organization    = {FH Aachen, University of Applied Sciences},
  isbn      = {978-3-88579-630-5},
  pages     = {35 -- 46},
  year      = {2014},
  language  = {de}
}
@inproceedings{KraftWilhelms2005,
  author    = {Kraft, Bodo and Wilhelms, Nils},
  title     = {Visual Knowledge Specification for Conceptual Design},
  year      = {2005},
  abstract  = {Proc. of the 2005 ASCE Intl. Conf. on Computing in Civil Engineering (ICCC 2005) eds. L. Soibelman und F. Pena-Mora, Seite 1-14, ASCE (CD-ROM), Cancun, Mexico, 2005 Current CAD tools are not able to support the fundamental conceptual design phase, and none of them provides consistency analyses of sketches produced by architects. To give architects a greater support at the conceptual design phase, we develop a CAD tool for conceptual design and a knowledge specification tool allowing the definition of conceptually relevant knowledge. The knowledge is specific to one class of buildings and can be reused. Based on a dynamic knowledge model, different types of design rules formalize the knowledge in a graph-based realization. An expressive visual language provides a user-friendly, human readable representation. Finally, consistency analyses enable conceptual designs to be checked against this defined knowledge. In this paper we concentrate on the knowledge specification part of our project.},
  subject      = {CAD},
  language  = {en}
}
@inproceedings{BlumAlbannaBenninghausetal.2019,
  author    = {Blum, Yannik and Albanna, Walid and Benninghaus, Anne and Kotliar, Konstantin},
  title     = {Vasomotion in retinal vessels of patients presenting post hemorrhagic hydrocephalus following subarachnoid hemorrhage},
  series = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  booktitle = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  editor    = {Staat, Manfred and Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-22-6},
  doi       = {10.17185/duepublico/48750},
  pages     = {38 -- 39},
  year      = {2019},
  abstract  = {Clearance of blood components and fluid drainage play a crucial role in subarachnoid hemorrhage (SAH) and post hemorrhagic hydrocephalus (PHH). With the involvement of interstitial fluid (ISF) and cerebrospinal fluid (CSF), two pathways for the clearance of fluid and solutes in the brain are proposed. Starting at the level of capillaries, flow of ISF follows along the basement membranes in the walls of cerebral arteries out of the parenchyma to drain into the lymphatics and CSF [1]-[3]. Conversely, it is shown that CSF enters the parenchyma between glial and pial basement membranes of penetrating arteries [4]-[6]. Nevertheless, the involved structures and the contribution of either flow pathway to fluid balance between the subarachnoid space and interstitial space remains controversial. Low frequency oscillations in vascular tone are referred to as vasomotion and corresponding vasomotion waves are modeled as the driving force for flow of ISF out of the parenchyma [7]. Retinal vessel analysis (RVA) allows non-invasive measurement of retinal vessel vasomotion with respect to diameter changes [8]. Thus, the aim of the study is to investigate vasomotion in RVA signals of SAH and PHH patients.},
  language  = {en}
}
@inproceedings{AzarDigel2019,
  author    = {Azar, Fouad and Digel, Ilya},
  title     = {Utilization of fluorescence spectroscopy and neural networks in clinical analysis},
  series = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  booktitle = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  editor    = {Staat, Manfred and Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-22-6},
  doi       = {10.17185/duepublico/48750},
  pages     = {40 -- 41},
  year      = {2019},
  abstract  = {Fluorescence topography of human urine in combination with learning algorithms can provide a variant pattern recognition method in analytical clinical chemistry and, eventually, diagnosis.},
  language  = {en}
}
@inproceedings{SchreiberBarkschatKraft2014,
  author    = {Schreiber, Marc and Barkschat, Kai and Kraft, Bodo},
  title     = {Using Continuous Integration to organize and monitor the annotation process of domain specific corpora},
  series = {5th International Conference on Information and Communication Systems (ICICS) : 1-3 April 2014, Irbid, Jordanien},
  booktitle = {5th International Conference on Information and Communication Systems (ICICS) : 1-3 April 2014, Irbid, Jordanien},
  organization    = {International Conference on Information and Communication Systems <5, 2014, Irbid, Jordanien>},
  isbn      = {978-1-4799-3022-7},
  doi       = {10.1109/IACS.2014.6841958},
  pages     = {1 -- 6},
  year      = {2014},
  language  = {en}
}
@inproceedings{TranStaat2014,
  author    = {Tran, Thanh Ngoc and Staat, Manfred},
  title     = {Uncertain multimode failure and limit analysis of shells},
  series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona},
  booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona},
  editor    = {Onate, E.},
  organization    = {World Congress on Computational Mechanics <11, 2014, Barcelona>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{KirchhofKraft2004,
  author    = {Kirchhof, M. and Kraft, Bodo},
  title     = {UML-based modeling of architectural knowledge and design},
  year      = {2004},
  abstract  = {IASSE-2004 - 13th International Conference on Intelligent and Adaptive Systems and Software Engineering eds. W. Dosch, N. Debnath, pp. 245-250, ISCA, Cary, NC, 1-3 July 2004, Nice, France We introduce a UML-based model for conceptual design support in civil engineering. Therefore, we identify required extensions to standard UML. Class diagrams are used for elaborating building typespecific knowledge: Object diagrams, implicitly contained in the architect's sketch, are validated against the defined knowledge. To enable the use of industrial, domain-specific tools, we provide an integrated conceptual design extension. The developed tool support is based on graph rewriting. With our approach architects are enabled to deal with semantic objects during early design phase, assisted by incremental consistency checks.},
  subject      = {UML},
  language  = {en}
}
@inproceedings{BayerHeschelerArtmannetal.2019,
  author    = {Bayer, Robin and Hescheler, J{\"u}rgen and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Treating arterial hypertension in a cell culture well},
  series = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH AachenW},
  booktitle = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH AachenW},
  editor    = {Staat, Manfred and Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-22-6},
  doi       = {10.17185/duepublico/48750},
  pages     = {5 -- 6},
  year      = {2019},
  abstract  = {Hypertension describes the pathological increase of blood pressure, which is most commonly associated with the increase of vascular wall stiffness [1]. Referring to the "Deutsche Bluthochdruck Liga" this pathology shows a growing trend in our aging society. In order to find novel pharmacological and probably personalized treatments, we want to present a functional approach to study biomechanical properties of a human aortic vascular model. In this method review we will give an overview of recent studies which were carried out with the CellDrum technology [2] and underline the added value to already existing standard procedures known from the field of physiology. Herein described CellDrum technology is a system to measure functional mechanical properties of cell monolayers and thin tissue constructs in-vitro. Additionally, the CellDrum enables to elucidate the mechanical response of cells to pharmacological drugs, toxins and vasoactive agents. Due to its highly flexible polymer support, cells can also be mechanically stimulated by steady and cyclic biaxial stretching.},
  language  = {en}
}
@inproceedings{BohrnStuetzFleischeretal.2012,
  author    = {Bohrn, U. and St{\"u}tz, E. and Fleischer, M. and Sch{\"o}ning, Michael Josef and Wagner, P.},
  title     = {Towards a paradigm change - mammalian cells as sensitive biosensor layers for the detection of unexpected toxic substances in air},
  series = {Nanoscale Science and Technology (NS\&T´12) : Proceedings Book Humboldt Kolleg ; Tunisia, 17-19 March, 2012},
  booktitle = {Nanoscale Science and Technology (NS\&T´12) : Proceedings Book Humboldt Kolleg ; Tunisia, 17-19 March, 2012},
  editor    = {Abdelghani, Adnane and Sch{\"o}ning, Michael Josef},
  pages     = {44 -- 44},
  year      = {2012},
  language  = {en}
}
@inproceedings{HeerRedkowitzKraft2008,
  author    = {Heer, Thomas and Redkowitz, Daniel and Kraft, Bodo},
  title     = {Tool Support for the Integration of Light-Weight Ontologies},
  isbn      = {978-3-642-00670-8},
  year      = {2008},
  abstract  = {Abstract of the authors: In many areas of computer science ontologies become more and more important. The use of ontologies for domain modeling often brings up the issue of ontology integration. The task of merging several ontologies, covering specific subdomains, into one united ontology has to be solved. Many approaches for ontology integration aim at automating the process of ontology alignment. However, a complete automation is not feasible, and user interaction is always required. Nevertheless, most ontology integration tools offer only very limited support for the interactive part of the integration process. In this paper, we present a novel approach for the interactive integration of ontologies. The result of the ontology integration is incrementally updated after each definition of a correspondence between ontology elements. The user is guided through the ontologies to be integrated. By restricting the possible user actions, the integrity of all defined correspondences is ensured by the tool we developed. We evaluated our tool by integrating different regulations concerning building design.},
  subject      = {Ontologie <Wissensverarbeitung>},
  language  = {de}
}
@inproceedings{KromeSander2018,
  author    = {Krome, Cornelia and Sander, Volker},
  title     = {Time series analysis with apache spark and its applications to energy informatics},
  series = {Proceedings of the 7th DACH+ Conference on Energy Informatics},
  booktitle = {Proceedings of the 7th DACH+ Conference on Energy Informatics},
  doi       = {10.1186/s42162-018-0043-1},
  year      = {2018},
  abstract  = {In energy economy forecasts of different time series are rudimentary. In this study, a prediction for the German day-ahead spot market is created with Apache Spark and R. It is just an example for many different applications in virtual power plant environments. Other examples of use as intraday price processes, load processes of machines or electric vehicles, real time energy loads of photovoltaic systems and many more time series need to be analysed and predicted. This work gives a short introduction into the project where this study is settled. It describes the time series methods that are used in energy industry for forecasts shortly. As programming technique Apache Spark, which is a strong cluster computing technology, is utilised. Today, single time series can be predicted. The focus of this work is on developing a method to parallel forecasting, to process multiple time series simultaneously with R and Apache Spark.},
  language  = {en}
}
@inproceedings{KloockSchubertErmelenkoetal.2006,
  author    = {Kloock, Joachim P. and Schubert, J. and Ermelenko, Y. and Vlasov, Y. G. and Bratov, A. and Sch{\"o}ning, Michael Josef},
  title     = {Thin-film sensors with chalcogenide glass materials - a general survey},
  series = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...},
  booktitle = {Biochemical sensing utilisation of micro- and nanotechnologies : Warsaw, [23rd - 26th] November 2005 / ed. by M. Mascini ...},
  address   = {Warsaw},
  pages     = {92 -- 97},
  year      = {2006},
  language  = {en}
}
@inproceedings{YoshinobuSchoeningFingeretal.2003,
  author    = {Yoshinobu, T. and Sch{\"o}ning, Michael Josef and Finger, F. and Moritz, W. and Iwasaki, H.},
  title     = {Thin-film a-Si LAPS : Preparation and pH sensitivity},
  series = {Eurosensors XVII : the 17th European Conference on Solid-State Transducers ; University of Minho, Guimar{\~a}es, Portugal, September 21 - 24, 2003},
  booktitle = {Eurosensors XVII : the 17th European Conference on Solid-State Transducers ; University of Minho, Guimar{\~a}es, Portugal, September 21 - 24, 2003},
  pages     = {88 -- 89},
  year      = {2003},
  language  = {en}
}
@inproceedings{MansurovZhubanovaDigeletal.2008,
  author    = {Mansurov, Zulkhair and Zhubanova, Azhar A. and Digel, Ilya and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l and Savitskaja, Irina S. and Kozhalakova, A. A. and Kistaubaeva, Aida S.},
  title     = {The sorption of LPS toxic shock by nanoparticles on base of carbonized vegetable raw materials},
  year      = {2008},
  abstract  = {Immobilization of lactobacillus on high temperature carbonizated vegetable raw material (rice husk, grape stones) increases their physiological activity and the quantity of the antibacterial metabolits, that consequently lead to increase of the antagonistic activity of lactobacillus. It is implies that the use of the nanosorbents for the attachment of the probiotical microorganisms are highly perspective for decision the important problems, such as the probiotical preparations delivery to the right address and their attachment to intestines mucosa with the following detoxication of gastro-intestinal tract and the normalization of it's microecology. Besides that, thus, the received carbonizated nanoparticles have peculiar properties - ability to sorption of LPS toxical shock and, hence, to the detoxication of LPS.},
  subject      = {Kohlenstofffaser},
  language  = {en}
}
@inproceedings{StaatHeitzer2002,
  author    = {Staat, Manfred and Heitzer, Michael},
  title     = {The restricted influence of kinematic hardening on shakedown loads},
  year      = {2002},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratcheting. To this end it is important to make a clear distinction between the shakedown range and the ratcheting range. In cyclic plasticity more sophisticated hardening models have been suggested in order to model the strain evolution observed in ratcheting experiments. The hardening models used in shakedown analysis are comparatively simple. It is shown that shakedown analysis can make quite stable predictions of admissible load ranges despite the simplicity of the underlying hardening models. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis. Both give identical or similar shakedown ranges. Structural shakedown analyses show that the loading may have a more pronounced effect than the hardening model.},
  subject      = {Biomedizinische Technik},
  language  = {en}
}
@inproceedings{WeberTersteggeEngelsetal.1996,
  author    = {Weber, S. and Terstegge, Andreas and Engels, R. and Herzog, H. and Reinartz, R. and Reinhart, P. and Rongen, F. and M{\"u}ller-G{\"a}rtner, H. W. and Halling, H.},
  title     = {The KFA TierPET: performance characteristics and measurements},
  series = {Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2},
  booktitle = {Conference record / 1996 IEEE Nuclear Science Symposium [and Medical Imaging], November 2 - 9, 1996, Anaheim, California ; vol. 2},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {0-7803-3534-1},
  issn      = {1082-3654},
  pages     = {1117 -- 1119},
  year      = {1996},
  language  = {en}
}
@inproceedings{WeberTersteggeHallingetal.1995,
  author    = {Weber, S. and Terstegge, Andreas and Halling, H. and Herzog, H. and Reinartz, R. and Reinhart, P. and Rongen, F. and M{\"u}ller-G{\"a}rtner, H.-W.},
  title     = {The design of an animal PET: flexible geometry for achieving optimal spatial resolution or high sensitivity},
  series = {Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2},
  booktitle = {Conference record / 1995 IEEE Nuclear Science Symposium and Medical Imaging, October 21 - 28, 1995, San Francisco ; vol. 2},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  organization    = {Institute of Electrical and Electronics Engineers},
  isbn      = {078033180X ; 0780331818 ; 0780331826},
  pages     = {1002 -- 1005},
  year      = {1995},
  language  = {en}
}
@inproceedings{ArtmannStadlerEmbsetal.2010,
  author    = {Artmann, Gerhard and Stadler, Andreas M. and Embs, Jan P. and Zaccai, Giuseppe and B{\"u}ldt, Georg and Digel, Ilya and Temiz Artmann, Ayseg{\"u}l},
  title     = {The crucial role of water in a phase transition of hemoglobin at body temperature : [abstract]},
  year      = {2010},
  abstract  = {The observation of a temperature transition of hemoglobin occurring at a critical temperature close to body temperature},
  subject      = {H{\"a}moglobin},
  language  = {en}
}
@inproceedings{StadlerEmbsZerlinetal.2007,
  author    = {Stadler, Andreas M. and Embs, Jan P. and Zerlin, Kay and Digel, Ilya and Artmann, Gerhard and Zaccai, Joe and B{\"u}ldt, Georg},
  title     = {Temperature transitions of hemoglobin and cytosolic water diffusion in human red blood cells : [poster]},
  year      = {2007},
  abstract  = {Background Hemoglobin interactions in red blood cells Hemoglobin dynamics in human red blood cells Diffusion of H2O in red blood cells},
  subject      = {Erythrozyt},
  language  = {en}
}
@inproceedings{KreyerStollenwerkSchoening2013,
  author    = {Kreyer, J{\"o}rg and Stollenwerk, Dominik and Sch{\"o}ning, Michael Josef},
  title     = {Tagung des Forschernachwuchses der FH Aachen 20. November 2013 / ed.: J. Kreyer, D. Stollenwerk, M. J. Sch{\"o}ning},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {64 S.},
  year      = {2013},
  language  = {de}
}
@inproceedings{PijanowskaRemiszewskaPederzollietal.2006,
  author    = {Pijanowska, Dorota G. and Remiszewska, Elzbieta and Pederzolli, Cecilia and Lunelli, Lorenzo and Vendano, Michele and Canteri, Roberto and Dudzinski, Konrad and Kruk, Jerzy and Torbicz, Wladyslaw},
  title     = {Surface modification for microreactor fabrication},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1480},
  year      = {2006},
  abstract  = {In this paper, methods of surface modification of different supports, i.e. glass and polymeric beads for enzyme immobilisation are described. The developed method of enzyme immobilisation is based on Schiff's base formation between the amino groups on the enzyme surface and the aldehyde groups on the chemically modified surface of the supports. The surface of silicon modified by APTS and GOPS with immobilised enzyme was characterised by atomic force microscopy (AFM), time-of-flight secondary ion mass spectroscopy (ToF-SIMS) and infrared spectroscopy (FTIR). The supports with immobilised enzyme (urease) were also tested in combination with microreactors fabricated in silicon and Perspex, operating in a flow-through system. For microreactors filled with urease immobilised on glass beads (Sigma) and on polymeric beads (PAN), a very high and stable signal (pH change) was obtained. The developed method of urease immobilisation can be stated to be very effective.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{KraftNagl2003,
  author    = {Kraft, Bodo and Nagl, Manfred},
  title     = {Support of Conceptual Design in Civil Engineering by Graph-based Tools},
  year      = {2003},
  abstract  = {WS GTaD-2003 - The 1st Workshop on Graph Transformations and Design ed Grabska, E., Seite 6-7, Jagiellonian University Krakow. 2 pages},
  subject      = {CAD},
  language  = {de}
}
@inproceedings{WeldenSeverinsPoghossianetal.2022,
  author    = {Welden, Melanie and Severins, Robin and Poghossian, Arshak and Wege, Christina and Siegert, Petra and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Studying the immobilization of acetoin reductase with Tobacco mosaic virus particles on capacitive field-effect sensors},
  series = {2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN)},
  booktitle = {2022 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN)},
  publisher = {IEEE},
  isbn      = {978-1-6654-5860-3 (Online)},
  doi       = {10.1109/ISOEN54820.2022.9789657},
  pages     = {4 Seiten},
  year      = {2022},
  abstract  = {A capacitive electrolyte-insulator-semiconductor (EISCAP) biosensor modified with Tobacco mosaic virus (TMV) particles for the detection of acetoin is presented. The enzyme acetoin reductase (AR) was immobilized on the surface of the EISCAP using TMV particles as nanoscaffolds. The study focused on the optimization of the TMV-assisted AR immobilization on the Ta 2 O 5 -gate EISCAP surface. The TMV-assisted acetoin EISCAPs were electrochemically characterized by means of leakage-current, capacitance-voltage, and constant-capacitance measurements. The TMV-modified transducer surface was studied via scanning electron microscopy.},
  language  = {en}
}
@inproceedings{SrivastavaSinghDhandetal.2006,
  author    = {Srivastava, Alok and Singh, Virendra and Dhand, Chetna and Kaur, Manindar and Singh, Tejvir and Witte, Katrin and Scherer, Ulrich W.},
  title     = {Study of swift heavy ion modified conduction polymer composites for application as gas sensor},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1345},
  year      = {2006},
  abstract  = {A polyaniline-based conducting composite was prepared by oxidative polymerisation of aniline in a polyvinylchloride (PVC) matrix. The coherent free standing thin films of the composite were prepared by a solution casting method. The polyvinyl chloride-polyaniline composites exposed to 120 MeV ions of silicon with total ion fluence ranging from 1011 to 1013 ions/cm2, were observed to be more sensitive towards ammonia gas than the unirradiated composite. The response time of the irradiated composites was observed to be comparably shorter. We report for the first time the application of swift heavy ion modified insulating polymer conducting polymer (IPCP) composites for sensing of ammonia gas.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{MuellerVeggianNeskakisLiederetal.1978,
  author    = {M{\"u}ller-Veggian, Mattea and Neskakis, A. and Lieder, R. M. and Beuscher, H.},
  title     = {Study of rotational aligned bands in ¹⁹⁰,¹⁹²,¹⁹⁴ Au},
  series = {Nuclear interactions : International Conference on Nuclear Interactions held in Canberra, 28 Aug. - 1 Sept. 1978 / ed. by Brian Albert Robson. - (Lecture notes in physics ; 92)},
  booktitle = {Nuclear interactions : International Conference on Nuclear Interactions held in Canberra, 28 Aug. - 1 Sept. 1978 / ed. by Brian Albert Robson. - (Lecture notes in physics ; 92)},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-09102-8},
  pages     = {428},
  year      = {1978},
  language  = {en}
}
@inproceedings{StaatTran2022,
  author    = {Staat, Manfred and Tran, Ngoc Trinh},
  title     = {Strain based brittle failure criteria for rocks},
  series = {Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training, Hanoi, December 2-3, 2022},
  booktitle = {Proceedings of (NACOME2022) The 11th National Conference on Mechanics, Vol. 1. Solid Mechanics, Rock Mechanics, Artificial Intelligence, Teaching and Training, Hanoi, December 2-3, 2022},
  publisher = {Nha xuat ban Khoa hoc tu nhien va Cong nghe (Verlag Naturwissenschaft und Technik)},
  address   = {Hanoi},
  isbn      = {978-604-357-084-7},
  pages     = {500 -- 509},
  year      = {2022},
  abstract  = {When confining pressure is low or absent, extensional fractures are typical, with fractures occurring on unloaded planes in rock. These "paradox" fractures can be explained by a phenomenological extension strain failure criterion. In the past, a simple empirical criterion for fracture initiation in brittle rock has been developed. But this criterion makes unrealistic strength predictions in biaxial compression and tension. A new extension strain criterion overcomes this limitation by adding a weighted principal shear component. The weight is chosen, such that the enriched extension strain criterion represents the same failure surface as the Mohr-Coulomb (MC) criterion. Thus, the MC criterion has been derived as an extension strain criterion predicting failure modes, which are unexpected in the understanding of the failure of cohesive-frictional materials. In progressive damage of rock, the most likely fracture direction is orthogonal to the maximum extension strain. The enriched extension strain criterion is proposed as a threshold surface for crack initiation CI and crack damage CD and as a failure surface at peak P. Examples show that the enriched extension strain criterion predicts much lower volumes of damaged rock mass compared to the simple extension strain criterion.},
  language  = {en}
}
@inproceedings{KohlSchmidtsKloeseretal.2021,
  author    = {Kohl, Philipp and Schmidts, Oliver and Kl{\"o}ser, Lars and Werth, Henri and Kraft, Bodo and Z{\"u}ndorf, Albert},
  title     = {STAMP 4 NLP - an agile framework for rapid quality-driven NLP applications development},
  series = {Quality of Information and Communications Technology. QUATIC 2021},
  booktitle = {Quality of Information and Communications Technology. QUATIC 2021},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-85346-4},
  doi       = {10.1007/978-3-030-85347-1_12},
  pages     = {156 -- 166},
  year      = {2021},
  abstract  = {The progress in natural language processing (NLP) research over the last years, offers novel business opportunities for companies, as automated user interaction or improved data analysis. Building sophisticated NLP applications requires dealing with modern machine learning (ML) technologies, which impedes enterprises from establishing successful NLP projects. Our experience in applied NLP research projects shows that the continuous integration of research prototypes in production-like environments with quality assurance builds trust in the software and shows convenience and usefulness regarding the business goal. We introduce STAMP 4 NLP as an iterative and incremental process model for developing NLP applications. With STAMP 4 NLP, we merge software engineering principles with best practices from data science. Instantiating our process model allows efficiently creating prototypes by utilizing templates, conventions, and implementations, enabling developers and data scientists to focus on the business goals. Due to our iterative-incremental approach, businesses can deploy an enhanced version of the prototype to their software environment after every iteration, maximizing potential business value and trust early and avoiding the cost of successful yet never deployed experiments.},
  language  = {en}
}
@inproceedings{DigelTemizArtmannNojimaetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nojima, H. and Artmann, Gerhard},
  title     = {Some peculiarities of application of cluster ions generated by plasma in respect of indoor air purification :[abstract]},
  year      = {2003},
  abstract  = {Recently, the SHARP Corporation, Japan, has developed the world's first "Plasma Cluster Ions (PCI)" air purification technology using plasma discharge to generate cluster ions. The new plasma cluster device releases positive and negative ions into the air, which are able to decompose and deactivate harmful airborne substances by chemical reactions. Because cluster ions consist of positive and negative ions that normally exist in the natural world, they are completely harmless and safe to humans. The amount of ozone generated by cluster ions is less than 0.01 ppm, which is significantly less than the 0.05-ppm standard for industrial operations and consumer electronics. This amount, thus, has no harming effects whatsoever on the human body. But particular properties and chemical processes in PCI treatment are still under study. It has been shown that PCI in most cases show strongly pronounced irreversible killing effects in respect of airborne microflora due to free-radical induced reactions and can be considered as a potent technology to disinfect both home, medical and industrial appliances.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{SchreiberHirtbachKraftetal.2013,
  author    = {Schreiber, Marc and Hirtbach, Stefan and Kraft, Bodo and Steinmetzler, Andreas},
  title     = {Software in the city: visual guidance through large scale software projects},
  series = {Software Engineering 2013 : Fachtagung des GI-Fachbereichs Softwaretechnik, 26. Februar-1. M{\"a}rz 2013 in Aachen. (GI-Edition ; 213)},
  booktitle = {Software Engineering 2013 : Fachtagung des GI-Fachbereichs Softwaretechnik, 26. Februar-1. M{\"a}rz 2013 in Aachen. (GI-Edition ; 213)},
  editor    = {Kowalewski, Stefan},
  publisher = {Ges. f{\"u}r Informatik},
  address   = {Bonn},
  isbn      = {978-3-88579-607-7 ; 978-3-88579-609-1},
  pages     = {213 -- 224},
  year      = {2013},
  language  = {en}
}
@inproceedings{StaatDuong2016,
  author    = {Staat, Manfred and Duong, Minh Tuan},
  title     = {Smoothed Finite Element Methods for Nonlinear Solid Mechanics Problems: 2D and 3D Case Studies},
  series = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2},
  booktitle = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2},
  pages     = {440 -- 445},
  year      = {2016},
  abstract  = {The Smoothed Finite Element Method (SFEM) is presented as an edge-based and a facebased techniques for 2D and 3D boundary value problems, respectively. SFEMs avoid shortcomings of the standard Finite Element Method (FEM) with lower order elements such as overly stiff behavior, poor stress solution, and locking effects. Based on the idea of averaging spatially the standard strain field of the FEM over so-called smoothing domains SFEM calculates the stiffness matrix for the same number of degrees of freedom (DOFs) as those of the FEM. However, the SFEMs significantly improve accuracy and convergence even for distorted meshes and/or nearly incompressible materials. Numerical results of the SFEMs for a cardiac tissue membrane (thin plate inflation) and an artery (tension of 3D tube) show clearly their advantageous properties in improving accuracy particularly for the distorted meshes and avoiding shear locking effects.},
  language  = {en}
}
@inproceedings{KolditzAlbinFasseetal.2015,
  author    = {Kolditz, Melanie and Albin, Thivaharan and Fasse, Alessandro and Br{\"u}ggemann, Gert-Peter and Abel, Dirk and Albracht, Kirsten},
  title     = {Simulative Analysis of Joint Loading During Leg Press Exercise for Control Applications},
  series = {IFAC-PapersOnLine},
  volume    = {48},
  booktitle = {IFAC-PapersOnLine},
  number    = {20},
  doi       = {10.1016/j.ifacol.2015.10.179},
  pages     = {435 -- 440},
  year      = {2015},
  language  = {en}
}
@inproceedings{OlderogMohrBegingetal.2021,
  author    = {Olderog, M. and Mohr, P. and Beging, Stefan and Tsoumpas, C. and Ziemons, Karl},
  title     = {Simulation study on the role of tissue-scattered events in improving sensitivity for a compact time of flight compton positron emission tomograph},
  series = {2020 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC)},
  booktitle = {2020 IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC)},
  publisher = {IEEE},
  isbn      = {978-1-7281-7693-2},
  doi       = {10.1109/NSS/MIC42677.2020.9507901},
  pages     = {4 Seiten},
  year      = {2021},
  abstract  = {In positron emission tomography improving time, energy and spatial detector resolutions and using Compton kinematics introduces the possibility to reconstruct a radioactivity distribution image from scatter coincidences, thereby enhancing image quality. The number of single scattered coincidences alone is in the same order of magnitude as true coincidences. In this work, a compact Compton camera module based on monolithic scintillation material is investigated as a detector ring module. The detector interactions are simulated with Monte Carlo package GATE. The scattering angle inside the tissue is derived from the energy of the scattered photon, which results in a set of possible scattering trajectories or broken line of response. The Compton kinematics collimation reduces the number of solutions. Additionally, the time of flight information helps localize the position of the annihilation. One of the questions of this investigation is related to how the energy, spatial and temporal resolutions help confine the possible annihilation volume. A comparison of currently technically feasible detector resolutions (under laboratory conditions) demonstrates the influence on this annihilation volume and shows that energy and coincidence time resolution have a significant impact. An enhancement of the latter from 400 ps to 100 ps leads to a smaller annihilation volume of around 50\%, while a change of the energy resolution in the absorber layer from 12\% to 4.5\% results in a reduction of 60\%. The inclusion of single tissue-scattered data has the potential to increase the sensitivity of a scanner by a factor of 2 to 3 times. The concept can be further optimized and extended for multiple scatter coincidences and subsequently validated by a reconstruction algorithm.},
  language  = {en}
}
@inproceedings{StreunAlKaddoumParletal.2012,
  author    = {Streun, M. and Al-Kaddoum, R. and Parl, C. and Pietrzyk, U. and Ziemons, Karl and Waasen, S. van},
  title     = {Simulation studies of optical photons in monolithic block scintillators},
  series = {2011 IEEE Nuclear Science Symposium Conference Record (NSS/MIC)},
  booktitle = {2011 IEEE Nuclear Science Symposium Conference Record (NSS/MIC)},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-1-4673-0120-6 (electronic ISBN)},
  doi       = {10.1109/NSSMIC.2011.6154621},
  pages     = {1380 -- 1382},
  year      = {2012},
  abstract  = {The interest in PET detectors with monolithic block scintillators is growing. In order to obtain high spatial resolutions dedicated positioning algorithms are required. But even an ideal algorithm can only deliver information which is provided by the detector. In this simulation study we investigated the light distribution on one surface of cuboid LSO scintillators of different size. Scintillators with a large aspect ratio (small footprint and large height) showed significant position information only for a minimum interaction depth of the gamma particle. The results allow a quantitative estimate for a useful aspect ratio.},
  language  = {en}
}
@inproceedings{BehbahaniRibleMoulinecetal.2015,
  author    = {Behbahani, Mehdi and Rible, Sebastian and Moulinec, Charles and Fournier, Yvan and Nicolai, Mike and Crosetto, Paolo},
  title     = {Simulation of the FDA Centrifugal Blood Pump Using High Performance Computing},
  series = {World Academy of Science, Engineering and Technology International Journal of Mechanical and Mechatronics Engineering},
  volume    = {9},
  booktitle = {World Academy of Science, Engineering and Technology International Journal of Mechanical and Mechatronics Engineering},
  number    = {5},
  year      = {2015},
  language  = {en}
}
@inproceedings{FrotscherGossmannTemizArtmannetal.2013,
  author    = {Frotscher, Ralf and Goßmann, Matthias and Temiz Artmann, Ayseg{\"u}l and Staat, Manfred},
  title     = {Simulation of cardiac cell-seeded membranes using the edge-based smoothed FEM},
  series = {1st International Conference "Shell and Membrane Theories in Mechanics and Biology: From Macro- to Nanoscale Structures", Minsk, Belarus, Sept. 16-20, 2013},
  booktitle = {1st International Conference "Shell and Membrane Theories in Mechanics and Biology: From Macro- to Nanoscale Structures", Minsk, Belarus, Sept. 16-20, 2013},
  publisher = {Verl. d. Weißruss. Staatl. Univ.},
  address   = {Minsk},
  organization    = {International Conference Shell and Membrane Theories in Mechanics and Biology: From Macro- to Nanoscale Structures <1, 2013, Minsk>},
  isbn      = {978-985-553-135-8},
  pages     = {165 -- 167},
  year      = {2013},
  language  = {en}
}
@inproceedings{KremersPieper2015,
  author    = {Kremers, Alexander and Pieper, Martin},
  title     = {Simulation and Verification of Bionic Heat Exchangers with COMSOL Multiphysics® Software},
  series = {COMSOL Conference 2015 User Presentations ; COMSOL Conference 2015 Grenoble October 14 - 16, 2015 - World Trade Center, Grenoble, France},
  booktitle = {COMSOL Conference 2015 User Presentations ; COMSOL Conference 2015 Grenoble October 14 - 16, 2015 - World Trade Center, Grenoble, France},
  publisher = {COMSOL},
  address   = {G{\"o}ttingen ; Berlin},
  pages     = {6 Seiten},
  year      = {2015},
  language  = {en}
}
@inproceedings{FrotscherDuongStaat2015,
  author    = {Frotscher, Ralf and Duong, Minh Tuan and Staat, Manfred},
  title     = {Simulating beating cardiomyocytes with electromechanical coupling},
  series = {II. International Conference on Biomedical Technology : 28-30 October 2015 Hannover, Germany / T. Lenarz, P. Wriggers (Eds.)},
  booktitle = {II. International Conference on Biomedical Technology : 28-30 October 2015 Hannover, Germany / T. Lenarz, P. Wriggers (Eds.)},
  organization    = {International Conference on Biomedical Technology <2, 2015, Hannover>},
  pages     = {1 -- 2},
  year      = {2015},
  language  = {en}
}
@inproceedings{BarekFischerNavratiletal.2006,
  author    = {Barek, Jiri and Fischer, Jan and Navratil, Tomas and Peckova, Karolina and Yosypchuk, Bogdan},
  title     = {Silver solid amalgam electrodes as sensors for chemical carcinogens},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1554},
  year      = {2006},
  abstract  = {The applicability of differential pulse voltammetry (DPV) and adsorptive stripping voltammetry (AdSV) at a non-toxic meniscus-modified silver solid amalgam electrode (m-AgSAE) for the determination of trace amounts of genotoxic substances was demonstrated on the determination of micromolar and submicromolar concentrations of 3-nitrofluoranthene using methanol - 0.01 mol L-1 NaOH (9:1) mixture as a base electrolyte and of Ostazine Orange using 0.01 mol L-1 NaOH as a base electrolyte.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{BhattaraiFrotscherStaat2016,
  author    = {Bhattarai, Aroj and Frotscher, Ralf and Staat, Manfred},
  title     = {Significance of fibre geometry on passive-active response of pelvic muscles to evaluate pelvic dysfunction},
  series = {BioMedWomen: Proceedings of the international conference on clinical and bioengineering for women's health},
  booktitle = {BioMedWomen: Proceedings of the international conference on clinical and bioengineering for women's health},
  editor    = {Natal Jorge, Renato},
  publisher = {CRC Press},
  address   = {Boca Raton},
  isbn      = {978-1-138-02910-1},
  pages     = {185 -- 188},
  year      = {2016},
  language  = {en}
}
@inproceedings{TranTranMatthiesetal.2016,
  author    = {Tran, Ngoc Trinh and Tran, Thanh Ngoc and Matthies, H. G. and Stavroulakis, G. E. and Staat, Manfred},
  title     = {Shakedown analysis of plate bending analysis under stochastic uncertainty by chance constrained programming},
  series = {ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5-10 June 2016},
  booktitle = {ECCOMAS Congress 2016, VII European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island, Greece, 5-10 June 2016},
  editor    = {Papadrakakis, M.},
  pages     = {13 S.},
  year      = {2016},
  language  = {en}
}
@inproceedings{SchusserBaeckerLeinhosetal.2013,
  author    = {Schusser, Sebastian and B{\"a}cker, Matthias and Leinhos, Marcel and Krischer, M. and Wenzel, L. and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Sensorkonzept zur in vitro Echtzeitmessung des Degradationsverhaltens von biodegradierbaren Biopolymeren},
  series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  organization    = {Dresdner Sensor-Symposium <11, 2013>},
  isbn      = {978-3-9813484-5-3},
  pages     = {174 -- 177},
  year      = {2013},
  language  = {de}
}
@inproceedings{BaeckerSchusserLeinhosetal.2014,
  author    = {B{\"a}cker, Matthias and Schusser, Sebastian and Leinhos, Marcel and Poghossian, Arshak and Sch{\"o}ning, Michael Josef},
  title     = {Sensor system for the monitoring of degradation processes of biodegradable biopolymers},
  series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)},
  booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)},
  publisher = {VDE-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik},
  isbn      = {978-3-8007-3622-5},
  pages     = {1 -- 4},
  year      = {2014},
  language  = {en}
}
@inproceedings{WernerYoshinobuMiyamotoetal.2014,
  author    = {Werner, Frederik and Yoshinobu, T. and Miyamoto, K. and Sch{\"o}ning, Michael Josef and Wagner, Torsten},
  title     = {Semiconductor-based sensors for imaging of chemical processes},
  series = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)},
  booktitle = {Sensoren und Messsysteme 2014 ; Beitr{\"a}ge der 17. GMA/ITG-Fachtagung vom 3. bis 4. Juni 2014 in N{\"u}rnberg. (ITG-Fachbericht ; 250)},
  publisher = {VDE-Verl.},
  address   = {D{\"u}sseldorf},
  organization    = {VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik},
  isbn      = {978-3-8007-3622-5},
  pages     = {1 -- 5},
  year      = {2014},
  language  = {en}
}
@inproceedings{KraftNagl2003,
  author    = {Kraft, Bodo and Nagl, Manfred},
  title     = {Semantic tool support for conceptual design},
  year      = {2003},
  abstract  = {ITCE-2003 - 4th Joint Symposium on Information Technology in Civil Engineering ed Flood, I., Seite 1-12, ASCE (CD-ROM), Nashville, USA In this paper we discussed graph based tools to support architects during the conceptual design phase. Conceptual Design is defined before constructive design; the used concepts are more abstract. We develop two graph based approaches, a topdown using the graph rewriting system PROGRES and a more industrially oriented approach, where we extend the CAD system ArchiCAD. In both approaches, knowledge can be defined by a knowledge engineer, in the top-down approach in the domain model graph, in the bottom-up approach in the in an XML file. The defined knowledge is used to incrementally check the sketch and to inform the architect about violations of the defined knowledge. Our goal is to discover design error as soon as possible and to support the architect to design buildings with consideration of conceptual knowledge.},
  subject      = {CAD},
  language  = {en}
}
@inproceedings{KraftSchneider2005,
  author    = {Kraft, Bodo and Schneider, Gerd},
  title     = {Semantic Roomobjects for Conceptual Design Support : A Knowledge-based Approach},
  isbn      = {978-1-4020-3460-2},
  year      = {2005},
  abstract  = {In: Computer Aided Architectural Design Futures 2005 2005, Part 4, 207-216, DOI: http://dx.doi.org/10.1007/1-4020-3698-1_19 The conceptual design at the beginning of the building construction process is essential for the success of a building project. Even if some CAD tools allow elaborating conceptual sketches, they rather focus on the shape of the building elements and not on their functionality. We introduce semantic roomobjects and roomlinks, by way of example to the CAD tool ArchiCAD. These extensions provide a basis for specifying the organisation and functionality of a building and free architects being forced to directly produce detailed constructive sketches. Furthermore, we introduce consistency analyses of the conceptual sketch, based on an ontology containing conceptual relevant knowledge, specific to one class of buildings.},
  subject      = {CAD},
  language  = {en}
}
@inproceedings{GerhardsSanderBelloum2013,
  author    = {Gerhards, Michael and Sander, Volker and Belloum, Adam},
  title     = {Seamlessly enabling the use of cloud resources in workflows},
  series = {Cloud Computing 2013 : The Fourth International Conference on Cloud Computing, GRIDs, and Virtualization : May 27 - June 1, 2013 - Valencia, Spain},
  booktitle = {Cloud Computing 2013 : The Fourth International Conference on Cloud Computing, GRIDs, and Virtualization : May 27 - June 1, 2013 - Valencia, Spain},
  publisher = {Curren},
  address   = {Red Hook, NY},
  organization    = {International Conference on Cloud Computing, GRIDs, and Virtualization <4, 2013, Valencia>},
  isbn      = {978-1-61208-271-4},
  pages     = {108 -- 114},
  year      = {2013},
  language  = {en}
}