@inproceedings{SchoutetensDachwaldHeiligers2021,
  author    = {Schoutetens, Frederic and Dachwald, Bernd and Heiligers, Jeannette},
  title     = {Optimisation of photon-sail trajectories in the alpha-centauri system using evolutionary neurocontrol},
  series = {8th ICATT 2021},
  booktitle = {8th ICATT 2021},
  pages     = {1 -- 15},
  year      = {2021},
  abstract  = {With the increased interest for interstellar exploration after the discovery of exoplanets and the proposal by Breakthrough Starshot, this paper investigates the optimisation of photon-sail trajectories in Alpha Centauri. The prime objective is to find the optimal steering strategy for a photonic sail to get captured around one of the stars after a minimum-time transfer from Earth. By extending the idea of the Breakthrough Starshot project with a deceleration phase upon arrival, the mission's scientific yield will be increased. As a secondary objective, transfer trajectories between the stars and orbit-raising manoeuvres to explore the habitable zones of the stars are investigated. All trajectories are optimised for minimum time of flight using the trajectory optimisation software InTrance. Depending on the sail technology, interstellar travel times of 77.6-18,790 years can be achieved, which presents an average improvement of 30\% with respect to previous work. Still, significant technological development is required to reach and be captured in the Alpha-Centauri system in less than a century. Therefore, a fly-through mission arguably remains the only option for a first exploratory mission to Alpha Centauri, but the enticing results obtained in this work provide perspective for future long-residence missions to our closest neighbouring star system.},
  language  = {en}
}
@misc{HilleStumpfMayntzetal.2023,
  author    = {Hille, Sebastian and Stumpf, Eike and Mayntz, Joscha and Dahmann, Peter},
  title     = {Prediction of sound exposure caused by a landing motor glider with recuperating propellers},
  series = {AIAA SCITECH 2023 Forum},
  journal   = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2023-0211},
  year      = {2023},
  abstract  = {This paper presents an approach to predicting the sound exposure on the ground caused by a landing aircraft with recuperating propellers. The noise source along the trajectory of a flight specified for a steeper approach is simulated based on measurements of sound power levels and additional parameters of a single propeller placed in a wind tunnel. To validate the measured data/measurement results, these simulations are also supported by overflight measurements of a test aircraft. It is shown that the simple source models of propellers do not provide fully satisfactory results since the sound levels are estimated too low. Nevertheless, with a further reference comparison, margins for an acceptable increase in the sound power level of the aircraft on its now steeper approach path could be estimated. Thus, in this case, a +7 dB increase in SWL would not increase the SEL compared to the conventional approach within only 2 km ahead of the airfield.},
  language  = {en}
}
@inproceedings{SeefeldtBauerDachwaldetal.2015,
  author    = {Seefeldt, Patric and Bauer, Waldemar and Dachwald, Bernd and Grundmann, Jan Thimo and Straubel, Marco and Sznajder, Maciej and T{\´o}th, Norbert and Zander, Martin E.},
  title     = {Large lightweight deployable structures for planetary defence: solar sail propulsion, solar concentrator payloads, large-scale photovoltaic power},
  series = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  booktitle = {4th IAA Planetary Defense Conference - PDC 2015, 13-17 April 2015, Frascati, Roma, Italy},
  pages     = {24},
  year      = {2015},
  language  = {en}
}
@inproceedings{KapoorBollerGiljohannetal.2010,
  author    = {Kapoor, Hrshi and Boller, Christian and Giljohann, Sebastian and Braun, Carsten},
  title     = {Strategies for structural health monitoring implementation potential assessment in aircraft operational life extension considerations},
  series = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  booktitle = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  publisher = {Dt. Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  address   = {Berlin},
  organization    = {Deutsche Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  isbn      = {978-3-940283-28-3},
  pages     = {9},
  year      = {2010},
  language  = {en}
}
@inproceedings{LoebSchartnerDachwaldetal.2011,
  author    = {Loeb, Horst W. and Schartner, Karl-Heinz and Dachwald, Bernd and Ohndorf, Andreas and Seboldt, Wolfgang},
  title     = {An Interstellar - Heliopause mission using a combination of solar/radioisotope electric propulsion},
  series = {Presented at the 32nd International Electric Propulsion Conference},
  booktitle = {Presented at the 32nd International Electric Propulsion Conference},
  pages     = {1 -- 7},
  year      = {2011},
  abstract  = {There is common agreement within the scientific community that in order to understand our local galactic environment it will be necessary to send a spacecraft into the region beyond the solar wind termination shock. Considering distances of 200 AU for a new mission, one needs a spacecraft travelling at a speed of close to 10 AU/yr in order to keep the mission duration in the range of less than 25 yrs, a transfer time postulated by ESA.Two propulsion options for the mission have been proposed and discussed so far: the solar sail propulsion and the ballistic/radioisotope electric propulsion. As a further alternative, we here investigate a combination of solar-electric propulsion and radioisotope-electric propulsion. The solar-electric propulsion stage consists of six 22 cm diameter "RIT-22"ion thrusters working with a high specific impulse of 7377 s corresponding to a positive grid voltage of 5 kV. Solar power of 53 kW BOM is provided by a light-weight solar array. The REP-stage consists of four space-proven 10 cm diameter "RIT-10" ion thrusters that will be operating one after the other for 9 yrs in total. Four advanced radioisotope generators provide 648 W at BOM. The scientific instrument package is oriented at earlier studies. For its mass and electric power requirement 35 kg and 35 W are assessed, respectively. Optimized trajectory calculations, treated in a separate contribution, are based on our "InTrance" method.The program yields a burn out of the REP stage in a distance of 79.6 AU for a usage of 154 kg of Xe propellant. With a C3 = 45,1 (km/s)2 a heliocentric probe velocity of 10 AU/yr is reached at this distance, provided a close Jupiter gravity assist adds a velocity increment of 2.7 AU/yr. A transfer time of 23.8 yrs results for this scenario requiring about 450 kg Xe for the SEP stage, jettisoned at 3 AU. We interpret the SEP/REP propulsion as a competing alternative to solar sail and ballistic/REP propulsion. Omiting a Jupiter fly-by even allows more launch flexibility, leaving the mission duration in the range of the ESA specification.},
  language  = {en}
}
@inproceedings{QuitterMarinoBauschat2019,
  author    = {Quitter, Julius and Marino, Matthew and Bauschat, J.-Michael},
  title     = {Highly Non-Planar Aircraft Configurations: Estimation of Flight Mechanical Derivatives Using Low-Order Methods},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  pages     = {10 Seiten},
  year      = {2019},
  language  = {en}
}
@misc{ArtmannLinderBayeretal.2017,
  author    = {Artmann, Gerhard and Linder, Peter and Bayer, Robin and Gossmann, Matthias},
  title     = {Celldrum electrode arrangement for measuring mechanical stress [Patent of invention]},
  publisher = {WIPO},
  address   = {Geneva},
  pages     = {18 Seiten},
  year      = {2017},
  abstract  = {The invention pertains to a CellDrum electrode arrangement for measuring mechanical stress, comprising a mechanical holder (1 ) and a non-conductive membrane (4), whereby the membrane (4) is at least partially fixed at its circumference to the mechanical holder (1), keeping it in place when the membrane (4) may bend due to forces acting on the membrane (4), the mechanical holder (1) and the membrane (4) forming a container, whereby the membrane (1) within the container comprises an cell- membrane compound layer or biological material (3) adhered to the deformable membrane 4 which in response to stimulation by an agent may exert mechanical stress to the membrane (4) such that the membrane bending stage changes whereby the container may be filled with an electrolyte, whereby an electric contact (2) is arranged allowing to contact said electrolyte when filled into to the container, whereby within a predefined geometry to the fixing of the membrane (4) an electrode (7) is arranged, whereby the electrode (7) is electrically insulated with respect to the electric contact (2) as well as said electrolyte, whereby mechanical stress due to an agent may be measured as a change in capacitance.},
  language  = {en}
}
@inproceedings{GoettenFinger2019,
  author    = {G{\"o}tten, Falk and Finger, Felix},
  title     = {Conceptual Design of a Modular 150 kg Vertical Take-off and Landing Unmanned Aerial Vehicle},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  pages     = {1 -- 10},
  year      = {2019},
  language  = {en}
}
@inproceedings{FunkeKeinzBoerneretal.2016,
  author    = {Funke, Harald and Keinz, Jan and B{\"o}rner, S. and Hendrick, P. and Elsing, R.},
  title     = {Testing and analysis of the impact on engine cycle parameters and control system modifications using hydrogen or methane as fuel in an industrial gas turbine},
  series = {Progress in propulsion physics ; Volume 8},
  booktitle = {Progress in propulsion physics ; Volume 8},
  publisher = {EDP Sciences},
  address   = {o.O.},
  organization    = {European Conference for Aerospace Sciences <2013, M{\"u}nchen>},
  isbn      = {978-5-94588-191-4},
  doi       = {10.1051/eucass/201608409},
  pages     = {409 -- 426},
  year      = {2016},
  language  = {en}
}
@inproceedings{SchulzeMuehleisenFeyerl2018,
  author    = {Schulze, Sven and M{\"u}hleisen, M. and Feyerl, G{\"u}nter},
  title     = {Adaptive energy management strategy for a heavy-duty truck with a P2-hybrid topology},
  series = {18. Internationales Stuttgarter Symposium. Proceedings},
  booktitle = {18. Internationales Stuttgarter Symposium. Proceedings},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  doi       = {10.1007/978-3-658-21194-3},
  pages     = {75 -- 89},
  year      = {2018},
  language  = {en}
}
@article{SchirraBissonnetteBramesfeld2018,
  author    = {Schirra, Julian and Bissonnette, William and Bramesfeld, G{\"o}tz},
  title     = {Wake-model effects on induced drag prediction of staggered boxwings},
  series = {Aerospace},
  volume    = {5},
  journal   = {Aerospace},
  number    = {1},
  issn      = {2226-4310},
  doi       = {10.3390/aerospace5010014},
  year      = {2018},
  language  = {en}
}
@inproceedings{NowackRoethBuehrigPolaczeketal.2008,
  author    = {Nowack, N. and R{\"o}th, Thilo and B{\"u}hrig-Polaczek, A. and Klaus, G.},
  title     = {Advanced Sheet Metal Components Reinforced by Light Metal Cast Structures},
  series = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]},
  booktitle = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]},
  number    = {2},
  editor    = {Hirsch, J{\"u}rgen},
  isbn      = {978-3-527-32367-8},
  pages     = {2374 -- 2381},
  year      = {2008},
  language  = {en}
}
@inproceedings{HorikawaOkadaUtoetal.2019,
  author    = {Horikawa, Atsushi and Okada, Kunio and Uto, Takahiro and Uchiyama, Yuta and Wirsum, Manfred and Funke, Harald and Kusterer, Karsten},
  title     = {Application of Low NOx Micro-mix Hydrogen Combustion to 2MW Class Industrial Gas Turbine Combustor},
  series = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan},
  booktitle = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan},
  isbn      = {978-4-89111-010-9},
  pages     = {1 -- 6},
  year      = {2019},
  language  = {en}
}
@article{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Calculation Methodology for Predicting Exhaust Mass Flows and Exhaust Temperature Profiles for Heavy-Duty Vehicles},
  series = {SAE International Journal of Commercial Vehicles},
  volume    = {13},
  journal   = {SAE International Journal of Commercial Vehicles},
  number    = {2},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  issn      = {1946-3928},
  doi       = {10.4271/02-13-02-0009},
  pages     = {129 -- 143},
  year      = {2020},
  abstract  = {The predictive control of commercial vehicle energy management systems, such as vehicle thermal management or waste heat recovery (WHR) systems, are discussed on the basis of information sources from the field of environment recognition and in combination with the determination of the vehicle system condition. In this article, a mathematical method for predicting the exhaust gas mass flow and the exhaust gas temperature is presented based on driving data of a heavy-duty vehicle. The prediction refers to the conditions of the exhaust gas at the inlet of the exhaust gas recirculation (EGR) cooler and at the outlet of the exhaust gas aftertreatment system (EAT). The heavy-duty vehicle was operated on the motorway to investigate the characteristic operational profile. In addition to the use of road gradient profile data, an evaluation of the continuously recorded distance signal, which represents the distance between the test vehicle and the road user ahead, is included in the prediction model. Using a Fourier analysis, the trajectory of the vehicle speed is determined for a defined prediction horizon. To verify the method, a holistic simulation model consisting of several hierarchically structured submodels has been developed. A map-based submodel of a combustion engine is used to determine the EGR and EAT exhaust gas mass flows and exhaust gas temperature profiles. All simulation results are validated on the basis of the recorded vehicle and environmental data. Deviations from the predicted values are analyzed and discussed.},
  language  = {en}
}
@article{MeyerGranrathFeyerletal.2021,
  author    = {Meyer, Max-Arno and Granrath, Christian and Feyerl, G{\"u}nter and Richenhagen, Johannes and Kaths, Jakob and Andert, Jakob},
  title     = {Closed-loop platoon simulation with cooperative intelligent transportation systems based on vehicle-to-X communication},
  series = {Simulation Modelling Practice and Theory},
  volume    = {106},
  journal   = {Simulation Modelling Practice and Theory},
  number    = {Art. 102173},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1569-190X},
  doi       = {10.1016/j.simpat.2020.102173},
  year      = {2021},
  language  = {en}
}
@inproceedings{GeibenGoettenHavermann2020,
  author    = {Geiben, Benedikt and G{\"o}tten, Falk and Havermann, Marc},
  title     = {Aerodynamic analysis of a winged sub-orbital spaceplane},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/530170},
  year      = {2020},
  abstract  = {This paper primarily presents an aerodynamic CFD analysis of a winged spaceplane geometry based on the Japanese Space Walker proposal. StarCCM was used to calculate aerodynamic coefficients for a typical space flight trajectory including super-, trans- and subsonic Mach numbers and two angles of attack. Since the solution of the RANS equations in such supersonic flight regimes is still computationally expensive, inviscid Euler simulations can principally lead to a significant reduction in computational effort. The impact on accuracy of aerodynamic properties is further analysed by comparing both methods for different flight regimes up to a Mach number of 4.},
  language  = {en}
}
@article{GazdaMaurischat2020,
  author    = {Gazda, Quentin and Maurischat, Andreas},
  title     = {Special functions and Gauss-Thakur sums in higher rank and dimension},
  publisher = {De Gruyter},
  address   = {Berlin},
  pages     = {26 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{AdamsLosekammCzupalla2020,
  author    = {Adams, Moritz and Losekamm, Martin J. and Czupalla, Markus},
  title     = {Development of the Thermal Control System for the RadMap Telescope Experiment on the International Space Station},
  series = {International Conference on Environmental Systems},
  booktitle = {International Conference on Environmental Systems},
  pages     = {1 -- 10},
  year      = {2020},
  language  = {en}
}
@inproceedings{WuKemper2016,
  author    = {Wu, Ziyi and Kemper, Hans},
  title     = {The optimal 48 V - battery pack for a specific load profile of a heavy duty vehicle},
  series = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  booktitle = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  year      = {2016},
  language  = {en}
}
@inproceedings{SchirraBauschatWatmuff2014,
  author    = {Schirra, Julian and Bauschat, J.-Michael and Watmuff, J.H.},
  title     = {Accurate induced drag prediction for highly non-planar lifting systems},
  series = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia},
  booktitle = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia},
  pages     = {4 Seiten},
  year      = {2014},
  abstract  = {The impact of wake model effects is investigated for two highly non-planar lifting systems. Dependent on the geometrical arrangement of the configuration, the wake model shape is found to considerably affect the estimation. Particularly at higher angles of attack, an accurate estimation based on the common linear wake model approaches is involved.},
  language  = {en}
}
@inproceedings{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {In-flight vibration-based structural health monitoring of aircraft wings},
  series = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea},
  booktitle = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea},
  pages     = {10 Seiten},
  year      = {2016},
  abstract  = {This work presents a methodology for automated damage-sensitive feature extraction and anomaly detection under multivariate operational variability for in-flight assessment of wings. The method uses a passive excitation approach, i. e. without the need for artificial actuation. The modal system properties (natural frequencies and damping ratios) are used as damage-sensitive features. Special emphasis is placed on the use of Fiber Bragg Grating (FBG) sensing technology and the consideration of Operational and Environmental Variability (OEV). Measurements from a wind tunnel investigation with a composite cantilever equipped with FBG and piezoelectric sensors are used to successfully detect an impact damage. In addition, the feasibility of damage localisation and severity estimation is evaluated based on the coupling found between damageand OEV-induced feature changes.},
  language  = {en}
}
@inproceedings{BarnatBosse2016,
  author    = {Barnat, Miriam and Bosse, Elke},
  title     = {The challenge of creating meta-inferences: Combining data representing institutional and individual perspectives on first-year support in higher education},
  series = {9th Conference on Social Science Methodology of the International Sociological Association, Leicester, UK},
  booktitle = {9th Conference on Social Science Methodology of the International Sociological Association, Leicester, UK},
  pages     = {1 -- 20},
  year      = {2016},
  language  = {en}
}
@inproceedings{KleineKallweitMichauxetal.2016,
  author    = {Kleine, Harald and Kallweit, Stephan and Michaux, Frank and Havermann, Marc and Olivier, Herbert},
  title     = {PIV Measurement of Shock Wave Diffraction},
  series = {18th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2016, Lissabon},
  booktitle = {18th International Symposium on Applications of Laser Techniques to Fluid Mechanics, 2016, Lissabon},
  pages     = {1 -- 14},
  year      = {2016},
  language  = {en}
}
@inproceedings{SchleupenEngemannBagherietal.2016,
  author    = {Schleupen, Josef and Engemann, Heiko and Bagheri, Mohsen and Kallweit, Stephan},
  title     = {The potential of SMART climbing robot combined with a weatherproof cabin for rotor blade maintenance},
  series = {17th European Conference on Composite Materials - ECCM, Munich, Germany},
  booktitle = {17th European Conference on Composite Materials - ECCM, Munich, Germany},
  pages     = {1 -- 8},
  year      = {2016},
  language  = {en}
}
@inproceedings{FunkeKeinzHendrick2017,
  author    = {Funke, Harald and Keinz, Jan and Hendrick, P.},
  title     = {Experimental Evaluation of the Pollutant and Noise Emissions of the GTCP 36-300 Gas Turbine Operated with Kerosene and a Low NOX Micromix Hydrogen Combustor},
  series = {7th European Conference for Aeronautics and Space Sciences, EUCASS 2017},
  booktitle = {7th European Conference for Aeronautics and Space Sciences, EUCASS 2017},
  organization    = {7th European Conference for Aeronautics and Space Sciences, EUCASS 2017-125, Milan, Italy, July 2017},
  doi       = {10.13009/EUCASS2017-125},
  pages     = {10 Seiten},
  year      = {2017},
  language  = {en}
}
@inproceedings{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Map-Based Model for the Determination of Fuel Consumption for Internal Combustion Engines as a Function of Flight Altitude},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/490162},
  pages     = {13 Seiten},
  year      = {2020},
  abstract  = {In addition to very high safety and reliability requirements, the design of internal combustion engines (ICE) in aviation focuses on economic efficiency. The objective must be to design the aircraft powertrain optimized for a specific flight mission with respect to fuel consumption and specific engine power. Against this background, expert tools provide valuable decision-making assistance for the customer. In this paper, a mathematical calculation model for the fuel consumption of aircraft ICE is presented. This model enables the derivation of fuel consumption maps for different engine configurations. Depending on the flight conditions and based on these maps, the current and the integrated fuel consumption for freely definable flight emissions is calculated. For that purpose, an interpolation method is used, that has been optimized for accuracy and calculation time. The mission boundary conditions flight altitude and power requirement of the ICE form the basis for this calculation. The mathematical fuel consumption model is embedded in a parent program. This parent program presents the simulated fuel consumption by means of an example flight mission for a representative airplane. The focus of the work is therefore on reproducing exact consumption data for flight operations. By use of the empirical approaches according to Gagg-Farrar [1] the power and fuel consumption as a function of the flight altitude are determined. To substantiate this approaches, a 1-D ICE model based on the multi-physical simulation tool GT-Suite® has been created. This 1-D engine model offers the possibility to analyze the filling and gas change processes, the internal combustion as well as heat and friction losses for an ICE under altitude environmental conditions. Performance measurements on a dynamometer at sea level for a naturally aspirated ICE with a displacement of 1211 ccm used in an aviation aircraft has been done to validate the 1-D ICE model. To check the plausibility of the empirical approaches with respect to the fuel consumption and performance adjustment for the flight altitude an analysis of the ICE efficiency chain of the 1-D engine model is done. In addition, a comparison of literature and manufacturer data with the simulation results is presented.},
  language  = {en}
}
@inproceedings{StrieganStruthDickhoffetal.2019,
  author    = {Striegan, Constantin J. D. and Struth, Benjamin and Dickhoff, Jens and Kusterer, Karsten and Funke, Harald and Bohn, Dieter},
  title     = {Numerical Simulations of the Micromix DLN Hydrogen Combustion Technology with LES and Comparison to Results of RANS and Experimental Data},
  series = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan.},
  booktitle = {Proceedings of International Gas Turbine Congress 2019 Tokyo, November 17-22, 2019, Tokyo, Japan.},
  isbn      = {978-4-89111-010-9},
  pages     = {1 -- 9},
  year      = {2019},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalil, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modelling with Application in Industry 4.0},
  series = {IEEE Access},
  journal   = {IEEE Access},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{HailerWeberNevelingetal.2020,
  author    = {Hailer, Benjamin and Weber, Tobias and Neveling, Sebastian and Dera, Samuel and Arent, Jan-Christoph and Middendorf, Peter},
  title     = {Development of a test device to determine the frictional behavior between honeycomb and prepreg layers under realistic manufacturing conditions},
  series = {Journal of Sandwich Structures \& Materials},
  journal   = {Journal of Sandwich Structures \& Materials},
  number    = {Volume 23, Issue 7},
  publisher = {Sage},
  address   = {London},
  issn      = {1530-7972},
  doi       = {10.1177/1099636220923986},
  pages     = {3017 -- 3043},
  year      = {2020},
  abstract  = {In the friction tests between honeycomb with film adhesive and prepreg, the relative displacement occurs between the film adhesive and the prepreg. The film adhesive does not shift relative to the honeycomb. This is consistent with the core crush behavior where the honeycomb moves together with the film adhesive, as can be seen in Figure 2(a). The pull-through forces of the friction measurements between honeycomb and prepreg at 1 mm deformation are plotted in Figure 17(a). While the friction at 100°C is similar to the friction at 120°C, it decreases significantly at 130°C and exhibits a minimum at 140°C. At 150°C, the friction rises again slightly and then sharply at 160°C. Since the viscosity of the M18/1 prepreg resin drops significantly before it cures [23], the minimum friction at 140°C could result from a minimum viscosity of the mixture of prepreg resin and film adhesive before the bond subsequently cures. Figure 17(b) shows the mean value curve of the friction measurements at 140°C. The error bars, which represent the standard deviation, reveal the good repeatability of the tests. The force curve is approximately horizontal between 1 mm and 2 mm. The friction then slightly rises. As with interlaminar friction measurements, this could be due to the fact that resin is removed by friction and the proportion of boundary lubrication increases. Figure 18 shows the surfaces after the friction measurement. The honeycomb cell walls are clearly visible in the film adhesive. There are areas where the film adhesive is completely removed and the carrier material of the film adhesive becomes visible. In addition, the viscosity of the resin changes as the curing progresses during the friction test. This can also affect the force-displacement curve.},
  language  = {en}
}
@inproceedings{EnglhardWeberArent2021,
  author    = {Englhard, Markus and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Efficiency enhancement for CFRP-Prepregautoclave manufacturing by means of simulation-assisted loading optimization},
  series = {Proceedings of SAMPE Europe Conference 2021},
  booktitle = {Proceedings of SAMPE Europe Conference 2021},
  pages     = {8 Seiten},
  year      = {2021},
  abstract  = {A new method for improved autoclave loading within the restrictive framework of helicopter manufacturing is proposed. It is derived from experimental and numerical studies of the curing process and aims at optimizing tooling positions in the autoclave for fast and homogeneous heat-up. The mold positioning is based on two sets of information. The thermal properties of the molds, which can be determined via semi-empirical thermal simulation. The second information is a previously determined distribution of heat transfer coefficients inside the autoclave. Finally, an experimental proof of concept is performed to show a cycle time reduction of up to 31\% using the proposed methodology.},
  language  = {en}
}
@article{Maurischat2022,
  author    = {Maurischat, Andreas},
  title     = {Algebraic independence of the Carlitz period and its hyperderivatives},
  series = {Journal of Number Theory},
  volume    = {240},
  journal   = {Journal of Number Theory},
  publisher = {Elsevier},
  address   = {Orlando, Fla.},
  issn      = {0022-314X},
  doi       = {10.1016/j.jnt.2022.01.006},
  pages     = {145 -- 162},
  year      = {2022},
  language  = {en}
}
@inproceedings{StrieganHajAyedFunkeetal.2017,
  author    = {Striegan, C. and Haj Ayed, A. and Funke, Harald and Loechle, S. and Kazari, M. and Horikawa, A. and Okada, K. and Koga, K.},
  title     = {Numerical combustion and heat transfer simulations and validation for a hydrogen fueled "micromix" test combustor in industrial gas turbine applications},
  series = {Proceedings of the ASME Turbo Expo},
  booktitle = {Proceedings of the ASME Turbo Expo},
  number    = {Volume Part F130041-4B, 2017},
  isbn      = {978-079185085-5},
  doi       = {10.1115/GT2017-64719},
  year      = {2017},
  language  = {en}
}
@article{TekinAshikagaHorikawaetal.2018,
  author    = {Tekin, Nurettin and Ashikaga, Mitsugu and Horikawa, Atsushi and Funke, Harald},
  title     = {Enhancement of fuel flexibility of industrial gas turbines by development of innovative hydrogen combustion systems},
  series = {Gas for energy},
  journal   = {Gas for energy},
  number    = {2},
  publisher = {Vulkan-Verlag},
  address   = {Essen},
  pages     = {4},
  year      = {2018},
  abstract  = {For fuel flexibility enhancement hydrogen represents a possible alternative gas turbine fuel within future low emission power generation, in case of hydrogen production by the use of renewable energy sources such as wind energy or biomass. Kawasaki Heavy Industries, Ltd. (KHI) has research and development projects for future hydrogen society; production of hydrogen gas, refinement and liquefaction for transportation and storage, and utilization with gas turbine / gas engine for the generation of electricity. In the development of hydrogen gas turbines, a key technology is the stable and low NOx hydrogen combustion, especially Dry Low Emission (DLE) or Dry Low NOx (DLN) hydrogen combustion. Due to the large difference in the physical properties of hydrogen compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for DLE hydrogen combustion. Thus, the development of DLE hydrogen combustion technologies is an essential and challenging task for the future of hydrogen fueled gas turbines. The DLE Micro-Mix combustion principle for hydrogen fuel has been in development for many years to significantly reduce NOx emissions. This combustion principle is based on cross-flow mixing of air and gaseous hydrogen which reacts in multiple miniaturized "diffusion-type" flames. The major advantages of this combustion principle are the inherent safety against flashback and the low NOx-emissions due to a very short residence time of the reactants in the flame region of the micro-flames.},
  language  = {en}
}
@article{ThomaRavi2019,
  author    = {Thoma, Andreas and Ravi, Sridhar},
  title     = {Significance of parallel computing on the performance of Digital Image Correlation algorithms in MATLAB},
  pages     = {1 -- 17},
  year      = {2019},
  abstract  = {Digital Image Correlation (DIC) is a powerful tool used to evaluate displacements and deformations in a non-intrusive manner. By comparing two images, one of the undeformed reference state of a specimen and another of the deformed target state, the relative displacement between those two states is determined. DIC is well known and often used for post-processing analysis of in-plane displacements and deformation of specimen. Increasing the analysis speed to enable real-time DIC analysis will be beneficial and extend the field of use of this technique. Here we tested several combinations of the most common DIC methods in combination with different parallelization approaches in MATLAB and evaluated their performance to determine whether real-time analysis is possible with these methods. To reflect improvements in computing technology different hardware settings were also analysed. We found that implementation problems can reduce the efficiency of a theoretically superior algorithm such that it becomes practically slower than a suboptimal algorithm. The Newton-Raphson algorithm in combination with a modified Particle Swarm algorithm in parallel image computation was found to be most effective. This is contrary to theory, suggesting that the inverse-compositional Gauss-Newton algorithm is superior. As expected, the Brute Force Search algorithm is the least effective method. We also found that the correct choice of parallelization tasks is crucial to achieve improvements in computing speed. A poorly chosen parallelisation approach with high parallel overhead leads to inferior performance. Finally, irrespective of the computing mode the correct choice of combinations of integerpixel and sub-pixel search algorithms is decisive for an efficient analysis. Using currently available hardware realtime analysis at high framerates remains an aspiration.},
  language  = {en}
}
@inproceedings{HoevelerJanser2016,
  author    = {Hoeveler, Bastian and Janser, Frank},
  title     = {The aerodynamically optimized design of a fan-in-wing duct},
  series = {Applied Aerodynamics Research Conference 2016, Bristol, GB, Jul 19-21, 2016},
  booktitle = {Applied Aerodynamics Research Conference 2016, Bristol, GB, Jul 19-21, 2016},
  isbn      = {1-85768-371-4},
  pages     = {1 -- 10},
  year      = {2016},
  language  = {en}
}
@article{WeberEnglhardArentetal.2019,
  author    = {Weber, Tobias and Englhard, Markus and Arent, Jan-Christoph and Hausmann, Joachim},
  title     = {An experimental characterization of wrinkling generated during prepreg autoclave manufacturing using caul plates},
  series = {Journal of Composite Materials},
  volume    = {53},
  journal   = {Journal of Composite Materials},
  number    = {26-27},
  issn      = {1530-793X},
  doi       = {10.1177/0021998319846556},
  pages     = {3757 -- 3773},
  year      = {2019},
  language  = {en}
}
@article{OttenWeberArent2018,
  author    = {Otten, Dennis and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation - On Its Way to Industrial Application},
  series = {International Journal of Aviation, Aeronautics, and Aerospace},
  volume    = {5},
  journal   = {International Journal of Aviation, Aeronautics, and Aerospace},
  number    = {2},
  publisher = {Embry-Riddle Aeronautical University},
  address   = {Daytona Beach, Fla.},
  issn      = {2374-6793},
  doi       = {10.15394/ijaaa.2018.1217},
  year      = {2018},
  abstract  = {Manufacturing process simulation (MPS) has become more and more important for aviation and the automobile industry. A highly competitive market requires the use of high performance metals and composite materials in combination with reduced manufacturing cost and time as well as a minimization of the time to market for a new product. However, the use of such materials is expensive and requires sophisticated manufacturing processes. An experience based process and tooling design followed by a lengthy trial-and-error optimization is just not contemporary anymore. Instead, a tooling design process aided by simulation is used more often. This paper provides an overview of the capabilities of MPS in the fields of sheet metal forming and prepreg autoclave manufacturing of composite parts summarizing the resulting benefits for tooling design and manufacturing engineering. The simulation technology is explained briefly in order to show several simplification and optimization techniques for developing industrialized simulation approaches. Small case studies provide examples of an efficient application on an industrial scale.},
  language  = {en}
}
@article{WeberRuffStahl2017,
  author    = {Weber, Tobias and Ruff-Stahl, Hans-Joachim K.},
  title     = {Advances in Composite Manufacturing of Helicopter Parts},
  series = {International Journal of Aviation, Aeronautics, and Aerospace},
  volume    = {4},
  journal   = {International Journal of Aviation, Aeronautics, and Aerospace},
  number    = {1},
  issn      = {2374-6793},
  doi       = {10.15394/ijaaa.2017.1153},
  year      = {2017},
  language  = {en}
}
@article{WeberArentSteffenetal.2017,
  author    = {Weber, Tobias and Arent, Jan-Christoph and Steffen, Lucas and Balvers, Johannes M. and Duhovic, Miro},
  title     = {Thermal optimization of composite autoclave molds using the shift factor approach for boundary condition estimation},
  series = {Journal of Composite Materials},
  volume    = {51},
  journal   = {Journal of Composite Materials},
  number    = {12},
  publisher = {Sage},
  address   = {London},
  issn      = {1530-793X},
  doi       = {10.1177/0021998317699868},
  pages     = {1753 -- 1767},
  year      = {2017},
  language  = {en}
}
@inproceedings{OttenSchmidtWeber2016,
  author    = {Otten, D. and Schmidt, M. and Weber, Tobias},
  title     = {Advances in Determination of Material Parameters for Functional Simulations Based on Process Simulations},
  series = {SAMPE Europe Conference 16 Liege},
  booktitle = {SAMPE Europe Conference 16 Liege},
  isbn      = {978-1-5108-3800-0},
  pages     = {570 -- 577},
  year      = {2016},
  language  = {en}
}
@inproceedings{WeberTellisDuhovic2016,
  author    = {Weber, Tobias and Tellis, Jane J. and Duhovic, Miro},
  title     = {Characterization of tool-part-interaction an interlaminar friction for manufacturing process simulation},
  series = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016},
  booktitle = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016},
  isbn      = {978-3-00-053387-7},
  pages     = {1 -- 7},
  year      = {2016},
  language  = {en}
}
@article{WeberArentMuenchetal.2016,
  author    = {Weber, Tobias and Arent, Jan-Christoph and M{\"u}nch, Lukas and Duhovic, Miro and Balvers, Johannes M.},
  title     = {A fast method for the generation of boundary conditions for thermal autoclave simulation},
  series = {Composites Part A},
  volume    = {88},
  journal   = {Composites Part A},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-835X},
  doi       = {10.1016/j.compositesa.2016.05.036},
  pages     = {216 -- 225},
  year      = {2016},
  abstract  = {Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.},
  language  = {en}
}
@inproceedings{HailerWeberArent2019,
  author    = {Hailer, Benjamin and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for Autoclave-Produced Sandwich Structures},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 8},
  year      = {2019},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2019,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 10},
  year      = {2019},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2015,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference, Amiens , France},
  booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France},
  pages     = {1 -- 10},
  year      = {2015},
  language  = {en}
}
@inproceedings{Weber2015,
  author    = {Weber, Tobias},
  title     = {Manufacturing Process Simulation for Tooling Optimization: Reduction of Quality Issues During Autoclave Manufacturing of Composite Parts},
  series = {Proceedings of SAMPE Europe Conference 2015, Amiens, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2015, Amiens, France},
  pages     = {1 -- 8},
  year      = {2015},
  language  = {en}
}
@inproceedings{OttenSchmidWeber2015,
  author    = {Otten, D. and Schmid, M. and Weber, Tobias},
  title     = {Advances In Sheet Metal-Forming: Reduction Of Tooling Cost By Methodical Optimization},
  series = {Proceedings of SAMPE Europe Conference, Amiens , France},
  booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France},
  year      = {2015},
  language  = {en}
}
@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalili, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modeling with Application in Industry 4.0},
  series = {IEEE Access},
  volume    = {8},
  journal   = {IEEE Access},
  number    = {Art. 9108222},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {111381 -- 111393},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{MaurischatPerkins2020,
  author    = {Maurischat, Andreas and Perkins, Rudolph},
  title     = {Taylor coefficients of Anderson generating functions and Drinfeld torsion extensions},
  number    = {Vol. 18, No. 01},
  publisher = {World Scientific},
  address   = {Singapur},
  doi       = {10.1142/S1793042122500099},
  pages     = {113 -- 130},
  year      = {2020},
  abstract  = {We generalize our work on Carlitz prime power torsion extension to torsion extensions of Drinfeld modules of arbitrary rank. As in the Carlitz case, we give a description of these extensions in terms of evaluations of Anderson generating functions and their hyperderivatives at roots of unity. We also give a direct proof that the image of the Galois representation attached to the p-adic Tate module lies in the p-adic points of the motivic Galois group. This is a generalization of the corresponding result of Chang and Papanikolas for the t-adic case.},
  language  = {en}
}