@inproceedings{KapoorBollerGiljohannetal.2010,
  author    = {Kapoor, Hrshi and Boller, Christian and Giljohann, Sebastian and Braun, Carsten},
  title     = {Strategies for structural health monitoring implementation potential assessment in aircraft operational life extension considerations},
  series = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  booktitle = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  publisher = {Dt. Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  address   = {Berlin},
  organization    = {Deutsche Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  isbn      = {978-3-940283-28-3},
  pages     = {9},
  year      = {2010},
  language  = {en}
}
@article{Staat2001,
  author    = {Staat, Manfred},
  title     = {Cyclic plastic deformation tests to verify FEM-based shakedown analyses},
  year      = {2001},
  abstract  = {Fatigue analyses are conducted with the aim of verifying that thermal ratcheting is limited. To this end it is important to make a clear distintion between the shakedown range and the ratcheting range (continuing deformation). As part of an EU-supported research project, experiments were carried out using a 4-bar model. The experiment comprised a water-cooled internal tube, and three insulated heatable outer test bars. The system was subjected to alternating axial forces, superimposed with alternating temperatures at the outer bars. The test parameters were partly selected on the basis of previous shakedown analyses. During the test, temperatures and strains were measured as a function of time. The loads and the resulting stresses were confirmed on an ongoing basis during performance of the test, and after it. Different material models were applied for this incremental elasto-plastic analysis using the ANSYS program. The results of the simulation are used to verify the FEM-based shakedown analysis.},
  subject      = {Materialerm{\"u}dung},
  language  = {en}
}
@article{MuschallikMolinnusJablonskietal.2020,
  author    = {Muschallik, Lukas and Molinnus, Denise and Jablonski, Melanie and Kipp, Carina Ronja and Bongaerts, Johannes and Pohl, Martina and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Selmer, Thorsten and Siegert, Petra},
  title     = {Synthesis of α-hydroxy ketones and vicinal (R, R)-diols by Bacillus clausii DSM 8716ᵀ butanediol dehydrogenase},
  series = {RSC Advances},
  volume    = {10},
  journal   = {RSC Advances},
  publisher = {Royal Society of Chemistry (RSC)},
  address   = {Cambridge},
  issn      = {2046-2069},
  doi       = {10.1039/D0RA02066D},
  pages     = {12206 -- 12216},
  year      = {2020},
  abstract  = {α-hydroxy ketones (HK) and 1,2-diols are important building blocks for fine chemical synthesis. Here, we describe the R-selective 2,3-butanediol dehydrogenase from B. clausii DSM 8716ᵀ (BcBDH) that belongs to the metal-dependent medium chain dehydrogenases/reductases family (MDR) and catalyzes the selective asymmetric reduction of prochiral 1,2-diketones to the corresponding HK and, in some cases, the reduction of the same to the corresponding 1,2-diols. Aliphatic diketones, like 2,3-pentanedione, 2,3-hexanedione, 5-methyl-2,3-hexanedione, 3,4-hexanedione and 2,3-heptanedione are well transformed. In addition, surprisingly alkyl phenyl dicarbonyls, like 2-hydroxy-1-phenylpropan-1-one and phenylglyoxal are accepted, whereas their derivatives with two phenyl groups are not substrates. Supplementation of Mn²⁺ (1 mM) increases BcBDH's activity in biotransformations. Furthermore, the biocatalytic reduction of 5-methyl-2,3-hexanedione to mainly 5-methyl-3-hydroxy-2-hexanone with only small amounts of 5-methyl-2-hydroxy-3-hexanone within an enzyme membrane reactor is demonstrated.},
  language  = {en}
}
@article{HorbachStaatPerezVianaetal.2020,
  author    = {Horbach, Andreas and Staat, Manfred and Perez-Viana, Daniel and Simmen, Hans-Peter and Neuhaus, Valentin and Pape, Hans-Christoph and Prescher, Andreas and Ciritsis, Bernhard},
  title     = {Biomechanical in vitro examination of a standardized low-volume tubular femoroplasty},
  series = {Clinical Biomechanics},
  volume    = {80},
  journal   = {Clinical Biomechanics},
  number    = {Art. 105104},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.1016/j.clinbiomech.2020.105104},
  year      = {2020},
  abstract  = {Background Osteoporosis is associated with the risk of fractures near the hip. Age and comorbidities increase the perioperative risk. Due to the ageing population, fracture of the proximal femur also proves to be a socio-economic problem. Preventive surgical measures have hardly been used so far. Methods 10 pairs of human femora from fresh cadavers were divided into control and low-volume femoroplasty groups and subjected to a Hayes fall-loading fracture test. The results of the respective localization and classification of the fracture site, the Singh index determined by computed tomography (CT) examination and the parameters in terms of fracture force, work to fracture and stiffness were evaluated statistically and with the finite element method. In addition, a finite element parametric study with different position angles and variants of the tubular geometry of the femoroplasty was performed. Findings Compared to the control group, the work to fracture could be increased by 33.2\%. The fracture force increased by 19.9\%. The used technique and instrumentation proved to be standardized and reproducible with an average poly(methyl methacrylate) volume of 10.5 ml. The parametric study showed the best results for the selected angle and geometry. Interpretation The cadaver studies demonstrated the biomechanical efficacy of the low-volume tubular femoroplasty. The numerical calculations confirmed the optimal choice of positioning as well as the inner and outer diameter of the tube in this setting. The standardized minimally invasive technique with the instruments developed for it could be used in further comparative studies to confirm the measured biomechanical results.},
  language  = {en}
}
@inproceedings{BeckerBergenerBreukeretal.2011,
  author    = {Becker, J{\"o}rg and Bergener, Philipp and Breuker, Dominic and Delfmann, Patrick and Eggert, Mathias},
  title     = {An Efficient Business Process Compliance Checking Approach},
  series = {Governance and Sustainability in Information Systems. Managing the Transfer and Diffusion of IT : IFIP WG 8.6 International Working Conference, Hamburg, Germany, September 22-24, 2011. Proceedings},
  booktitle = {Governance and Sustainability in Information Systems. Managing the Transfer and Diffusion of IT : IFIP WG 8.6 International Working Conference, Hamburg, Germany, September 22-24, 2011. Proceedings},
  publisher = {Springer},
  address   = {Berlin, Heidelberg},
  doi       = {10.1007/978-3-642-24148-2_19},
  pages     = {282 -- 287},
  year      = {2011},
  language  = {en}
}
@article{KramerValeroChansonetal.2019,
  author    = {Kramer, Matthias and Valero, Daniel and Chanson, Hubert and Bung, Daniel Bernhard},
  title     = {Towards reliable turbulence estimations with phase-detection probes: an adaptive window cross-correlation technique},
  series = {Experiments in Fluids},
  volume    = {60},
  journal   = {Experiments in Fluids},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1432-1114},
  doi       = {10.1007/s00348-018-2650-9},
  year      = {2019},
  language  = {en}
}
@article{FerreinJacobsLakemeyer2005,
  author    = {Ferrein, Alexander and Jacobs, Stefan and Lakemeyer, Gerhard},
  title     = {Controlling Unreal Tournament 2004 Bots with the logic-based action language Golog / Jacobs, Stefan ; Ferrein, Alexander ; Lakemeyer, Gerhard},
  series = {Proceedings of the First AAAI Conference on Artificial Intelligence and Interactive Digital Entertainment (AIIDE).},
  journal   = {Proceedings of the First AAAI Conference on Artificial Intelligence and Interactive Digital Entertainment (AIIDE).},
  pages     = {151 -- 152},
  year      = {2005},
  language  = {en}
}
@article{Staat2000,
  author    = {Staat, Manfred},
  title     = {Direct FEM Limit and Shakedown Analysis with Uncertain Data},
  year      = {2000},
  abstract  = {The structural reliability with respect to plastic collapse or to inadaptation is formulated on the basis of the lower bound limit and shakedown theorems. A direct definition of the limit state function is achieved which permits the use of the highly effective first order reliability methods (FORM) is achieved. The theorems are implemented into a general purpose FEM program in a way capable of large-scale analysis. The limit state function and its gradient are obtained from a mathematical optimization problem. This direct approach reduces considerably the necessary knowledge of uncertain technological input data, the computing time, and the numerical error, leading to highly effective and precise reliability analyses.},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}
@inproceedings{LahrsKrisamHerrmann2023,
  author    = {Lahrs, Lennart and Krisam, Pierre and Herrmann, Ulf},
  title     = {Envisioning a collaborative energy system planning platform for the energy transition at the district level},
  series = {ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems},
  booktitle = {ECOS 2023. The 36th International Conference on Efficiency, Cost, Optimization, Simulation and Environmental Impact of Energy Systems},
  publisher = {Procedings of ECOS 2023},
  doi       = {10.52202/069564-0284},
  pages     = {3163 -- 3170},
  year      = {2023},
  abstract  = {Residential and commercial buildings account for more than one-third of global energy-related greenhouse gas emissions. Integrated multi-energy systems at the district level are a promising way to reduce greenhouse gas emissions by exploiting economies of scale and synergies between energy sources. Planning district energy systems comes with many challenges in an ever-changing environment. Computational modelling established itself as the state-of-the-art method for district energy system planning. Unfortunately, it is still cumbersome to combine standalone models to generate insights that surpass their original purpose. Ideally, planning processes could be solved by using modular tools that easily incorporate the variety of competing and complementing computational models. Our contribution is a vision for a collaborative development and application platform for multi-energy system planning tools at the district level. We present challenges of district energy system planning identified in the literature and evaluate whether this platform can help to overcome these challenges. Further, we propose a toolkit that represents the core technical elements of the platform. Lastly, we discuss community management and its relevance for the success of projects with collaboration and knowledge sharing at their core.},
  language  = {en}
}
@article{KueppersSteffenHellmuthetal.2014,
  author    = {K{\"u}ppers, Tobias and Steffen, Victoria and Hellmuth, Hendrik and O'Connell, Timothy and Bongaerts, Johannes and Maurer, Karl-Heinz and Wiechert, Wolfgang},
  title     = {Developing a new production host from a blueprint: Bacillus pumilus as an industrial enzyme producer},
  series = {Microbial cell factories},
  volume    = {13},
  journal   = {Microbial cell factories},
  publisher = {BioMed Central},
  address   = {London},
  issn      = {1475-2859 (E-Journal)},
  doi       = {10.1186/1475-2859-13-46},
  pages     = {Article No. 46},
  year      = {2014},
  language  = {en}
}
@inproceedings{NiemuellerReuterFerrein2016,
  author    = {Niemueller, Tim and Reuter, Sebastian and Ferrein, Alexander},
  title     = {Fawkes for the RoboCup Logistics League},
  series = {RoboCup 2015: Robot World Cup XIX},
  booktitle = {RoboCup 2015: Robot World Cup XIX},
  editor    = {Almeida, Luis},
  publisher = {Springer International Publishing},
  address   = {Cham},
  isbn      = {978-3-319-29339-4},
  doi       = {10.1007/978-3-319-29339-4_31},
  pages     = {365 -- 373},
  year      = {2016},
  language  = {en}
}
@article{BassamArtmannHescheleretal.2011,
  author    = {Bassam, Rasha and Artmann, Gerhard and Hescheler, J{\"u}rgen and Graef, T. and Temiz Artmann, Ayseg{\"u}l and Porst, Dariusz and Linder, Peter and Kayser, Peter and Arinkin, Vladimir and Gossmann, Matthias and Digel, Ilya},
  title     = {Alterations in human hemoglobin structure related to red blood cell storage},
  year      = {2011},
  abstract  = {The importance of the availability of stored blood or blood cells, respectively, for urgent transfusion cannot be overestimated. Nowadays, blood storage becomes even more important since blood products are used for epidemiological studies, bio-technical research or banked for transfusion purposes. Thus blood samples must not only be processed, stored, and shipped to preserve their efficacy and safety, but also all parameters of storage must be recorded and reported for Quality Assurance. Therefore, blood banks and clinical research facilities are seeking more accurate, automated means for blood storage and blood processing.},
  subject      = {H{\"a}moglobin},
  language  = {en}
}
@inproceedings{BooysenMathewKnoxetal.2015,
  author    = {Booysen, Tracy and Mathew, Thomas and Knox, Greig and Fong, W. K. and St{\"u}ttgen, Marcel and Ferrein, Alexander and Steinbauer, Gerald},
  title     = {The Scarab Project},
  series = {ICRA 2015 Developing Countries Forum},
  booktitle = {ICRA 2015 Developing Countries Forum},
  pages     = {3 S.},
  year      = {2015},
  abstract  = {Urban Search and Rescue (USAR) is an active research field in the robotics community. Despite recent advances for many open research questions, these kind of systems are not widely used in real rescue missions. One reason is that such systems are complex and not (yet) very reliable; another is that one has to be an robotic expert to run such a system. Moreover, available rescue robots are very expensive and the benefits of using them are still limited. In this paper, we present the Scarab robot, an alternative design for a USAR robot. The robot is light weight, humanpackable and its primary purpose is that of extending the rescuer's capability to sense the disaster site. The idea is that a responder throws the robot to a certain spot. The robot survives the impact with the ground and relays sensor data such as camera images or thermal images to the responder's hand-held control unit from which the robot can be remotely controlled.},
  language  = {en}
}
@article{KnoxBruggemannGossmannetal.2020,
  author    = {Knox, Ronald and Bruggemann, Andrea and Gossmann, Matthias and Thomas, Ulrich and Horv{\´a}th, Andr{\´a}s and Dragicevic, Elena and Stoelzle-Feix, Sonja and Fertig, Niels and Jung, Alexander and Raman, Aravind Hariharan and Staat, Manfred and Linder, Peter},
  title     = {Combining physiological relevance and throughput for in vitro cardiac contractility measurement},
  series = {Biophysical Journal},
  volume    = {118},
  journal   = {Biophysical Journal},
  number    = {Issue 3, Supplement 1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0006-3495},
  doi       = {10.1016/j.bpj.2019.11.3104},
  pages     = {570a},
  year      = {2020},
  abstract  = {Despite increasing acceptance of human induced pluripotent stem cell-derived cardiomyocytes (hiPSC-CMs) in safety pharmacology, controversy remains about the physiological relevance of existing in vitro models for their mechanical testing. We hypothesize that existing signs of immaturity of the cell models result from an improper mechanical environment. We cultured hiPSC-CMs in a 96-well format on hyperelastic silicone membranes imitating their native mechanical environment, resulting in physiological responses to compound stimuli.We validated cell responses on the FLEXcyte 96, with a set of reference compounds covering a broad range of cellular targets, including ion channel modulators, adrenergic receptor modulators and kinase inhibitors. Acute (10 - 30 min) and chronic (up to 7 days) effects were investigated. Furthermore, the measurements were complemented with electromechanical models based on electrophysiological recordings of the used cell types.hiPSC-CMs were cultured on freely-swinging, ultra-thin and hyperelastic silicone membranes. The weight of the cell culture medium deflects the membranes downwards. Rhythmic contraction of the hiPSC-CMs resulted in dynamic deflection changes which were quantified by capacitive distance sensing. The cells were cultured for 7 days prior to compound addition. Acute measurements were conducted 10-30 minutes after compound addition in standard culture medium. For chronic treatment, compound-containing medium was replaced daily for up to 7 days. Electrophysiological properties of the employed cell types were recorded by automated patch-clamp (Patchliner) and the results were integrated into the electromechanical model of the system.Calcium channel agonist S Bay K8644 and beta-adrenergic stimulator isoproterenol induced significant positive inotropic responses without additional external stimulation. Kinase inhibitors displayed cardiotoxic effects on a functional level at low concentrations. The system-integrated analysis detected alterations in beating shape as well as frequency and arrhythmic events and we provide a quantitative measure of these.},
  language  = {en}
}
@article{FerreinSteinbauer2016,
  author    = {Ferrein, Alexander and Steinbauer, Gerald},
  title     = {Looking back on 20 Years of RoboCup},
  series = {KI - K{\"u}nstliche Intelligenz},
  volume    = {30},
  journal   = {KI - K{\"u}nstliche Intelligenz},
  number    = {3-4},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1610-1987},
  doi       = {10.1007/s13218-016-0443-y},
  pages     = {321 -- 323},
  year      = {2016},
  language  = {en}
}
@inproceedings{MoehringWulfhorstRothetal.2016,
  author    = {M{\"o}hring, S. and Wulfhorst, H. and Roth, J. and Tippk{\"o}tter, Nils},
  title     = {Pretreatment strategies for lignocellulosic biomass},
  series = {New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany},
  booktitle = {New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany},
  publisher = {DECHEMA},
  address   = {Frankfurt am Main},
  pages     = {131},
  year      = {2016},
  language  = {en}
}
@article{NguyenXuanRabczukNguyenThoietal.2011,
  author    = {Nguyen-Xuan, H. and Rabczuk, T. and Nguyen-Thoi, T. and Tran, Thanh Ngoc and Nguyen-Thanh, N.},
  title     = {Computation of limit and shakedown loads using a node-based smoothed finite element method},
  series = {International Journal for Numerical Methods in Engineering},
  volume    = {90},
  journal   = {International Journal for Numerical Methods in Engineering},
  number    = {3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1097-0207},
  doi       = {10.1002/nme.3317},
  pages     = {287 -- 310},
  year      = {2011},
  abstract  = {This paper presents a novel numerical procedure for computing limit and shakedown loads of structures using a node-based smoothed FEM in combination with a primal-dual algorithm. An associated primal-dual form based on the von Mises yield criterion is adopted. The primal-dual algorithm together with a Newton-like iteration are then used to solve this associated primal-dual form to determine simultaneously both approximate upper and quasi-lower bounds of the plastic collapse limit and the shakedown limit. The present formulation uses only linear approximations and its implementation into finite element programs is quite simple. Several numerical examples are given to show the reliability, accuracy, and generality of the present formulation compared with other available methods.},
  language  = {en}
}
@article{FerreinRensMeyeretal.2011,
  author    = {Ferrein, Alexander and Rens, Gavin and Meyer, Thomas and Lakemeyer, Gerhard},
  title     = {A Logic for Specifying Partially Observable Stochastic Domains / Rens, Gavin ; Meyer, Thomas ; Ferrein, Alexander ; Lakemeyer, Gerhard},
  series = {Proceedings of the Ninth International Workshop pn non-Monotonic Reasoning, Action and Change (NRAC`11)},
  journal   = {Proceedings of the Ninth International Workshop pn non-Monotonic Reasoning, Action and Change (NRAC`11)},
  pages     = {15 -- 22},
  year      = {2011},
  language  = {en}
}
@inproceedings{SauerbornLiebenstundRaueetal.2017,
  author    = {Sauerborn, Markus and Liebenstund, Lena and Raue, Markus and Mang, Thomas and Herrmann, Ulf and Dueing, Andreas},
  title     = {Analytic method for material aging and quality analyzing to forecast long time stability of plastic micro heliostat components},
  series = {AIP Conference Proceedings},
  volume    = {1850},
  booktitle = {AIP Conference Proceedings},
  number    = {1},
  doi       = {10.1063/1.4984388},
  pages     = {030045-1 -- 030045-8},
  year      = {2017},
  language  = {en}
}
@article{TranStaat2021,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {Direct plastic structural design under random strength and random load by chance constrained programming},
  series = {European Journal of Mechanics - A/Solids},
  volume    = {85},
  journal   = {European Journal of Mechanics - A/Solids},
  number    = {Article 104106},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0997-7538},
  doi       = {10.1016/j.euromechsol.2020.104106},
  year      = {2021},
  language  = {en}
}
@inproceedings{RothMoehringTippkoetter2016,
  author    = {Roth, J. and M{\"o}hring, S. and Tippk{\"o}tter, Nils},
  title     = {Characterization and evaluation of lignocellulosic biomass 130 hydrolysates for ABE fermentation},
  series = {New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany},
  booktitle = {New frontiers of biotech-processes (Himmelfahrtstagung) : 02-04 May 2016, Rhein-Mosel-Halle, Koblenz/Germany},
  publisher = {DECHEMA},
  address   = {Frankfurt am Main},
  pages     = {130},
  year      = {2016},
  language  = {en}
}
@inproceedings{FrauenrathGoemmelButenwegetal.2010,
  author    = {Frauenrath, Tobias and G{\"o}mmel, Andreas and Butenweg, Christoph and Otten, Mario and Niendorf, Thoralf},
  title     = {3D mapping of vocal fold geometry during articulatory maneuvers using ultrashort echo time imaging at 3.0 T},
  series = {ISMRM-ESMRMB joint annual meeting 2010, Band 4},
  booktitle = {ISMRM-ESMRMB joint annual meeting 2010, Band 4},
  publisher = {Curran},
  address   = {Red Hook, NY},
  organization    = {International Society of Magnetic Resonance in Medicine},
  isbn      = {978-1-617-82008-3},
  pages     = {3087},
  year      = {2010},
  language  = {en}
}
@inproceedings{WarerkarSchmitzGoettscheetal.2009,
  author    = {Warerkar, Shashikant and Schmitz, Stefan and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Reißel, Martin and Tamme, Rainer},
  title     = {Air-sand heat exchanger for high-temperature storage},
  series = {Proceedings of the ASME 3rd International Conference on Energy Sustainability : July 19 - 23, 2009, San Francisco, California, USA. Vol. 2},
  booktitle = {Proceedings of the ASME 3rd International Conference on Energy Sustainability : July 19 - 23, 2009, San Francisco, California, USA. Vol. 2},
  publisher = {ASME},
  address   = {New York, NY},
  isbn      = {978-0-7918-4890-6},
  pages     = {655 -- 661},
  year      = {2009},
  language  = {en}
}
@article{HeuermannSchiek1994,
  author    = {Heuermann, Holger and Schiek, Burkhard},
  title     = {Scattering Parameter Measurements of Microstrip Devices using the Double-LNN Calibration Technique},
  series = {Conference proceedings : [Palais des Festivals et des Congr{\`e}s Cannes, France, 5 - 8 September 1994]},
  journal   = {Conference proceedings : [Palais des Festivals et des Congr{\`e}s Cannes, France, 5 - 8 September 1994]},
  publisher = {Nexus Business Communications},
  address   = {Swanley},
  isbn      = {0-9518032-5-5},
  year      = {1994},
  language  = {en}
}
@inproceedings{DigelDemirciTrzewiketal.2004,
  author    = {Digel, Ilya and Demirci, Taylan and Trzewik, J{\"u}rgen and Linder, Peter and Temiz Artmann, Ayseg{\"u}l},
  title     = {Fibroblast response to mechanical stress: role of the adhesion substrate : [abstract]},
  year      = {2004},
  abstract  = {Mechanical stimulation of the cells resulted in evident changes in the cell morphology, protein composition and gene expression. Microscopically, additional formation of stress fibers accompanied by cell re-arrangements in a monolayer was observed. Also, significant activation of p53 gene was revealed as compared to control. Interestingly, the use of CellTech membrane coating induced cell death after mechanical stress had been applied. Such an effect was not detected when fibronectin had been used as an adhesion substrate.},
  subject      = {Fibroblast},
  language  = {en}
}
@inproceedings{LoebSchartnerDachwaldetal.2011,
  author    = {Loeb, Horst W. and Schartner, Karl-Heinz and Dachwald, Bernd and Ohndorf, Andreas and Seboldt, Wolfgang},
  title     = {An Interstellar - Heliopause mission using a combination of solar/radioisotope electric propulsion},
  series = {Presented at the 32nd International Electric Propulsion Conference},
  booktitle = {Presented at the 32nd International Electric Propulsion Conference},
  pages     = {1 -- 7},
  year      = {2011},
  abstract  = {There is common agreement within the scientific community that in order to understand our local galactic environment it will be necessary to send a spacecraft into the region beyond the solar wind termination shock. Considering distances of 200 AU for a new mission, one needs a spacecraft travelling at a speed of close to 10 AU/yr in order to keep the mission duration in the range of less than 25 yrs, a transfer time postulated by ESA.Two propulsion options for the mission have been proposed and discussed so far: the solar sail propulsion and the ballistic/radioisotope electric propulsion. As a further alternative, we here investigate a combination of solar-electric propulsion and radioisotope-electric propulsion. The solar-electric propulsion stage consists of six 22 cm diameter "RIT-22"ion thrusters working with a high specific impulse of 7377 s corresponding to a positive grid voltage of 5 kV. Solar power of 53 kW BOM is provided by a light-weight solar array. The REP-stage consists of four space-proven 10 cm diameter "RIT-10" ion thrusters that will be operating one after the other for 9 yrs in total. Four advanced radioisotope generators provide 648 W at BOM. The scientific instrument package is oriented at earlier studies. For its mass and electric power requirement 35 kg and 35 W are assessed, respectively. Optimized trajectory calculations, treated in a separate contribution, are based on our "InTrance" method.The program yields a burn out of the REP stage in a distance of 79.6 AU for a usage of 154 kg of Xe propellant. With a C3 = 45,1 (km/s)2 a heliocentric probe velocity of 10 AU/yr is reached at this distance, provided a close Jupiter gravity assist adds a velocity increment of 2.7 AU/yr. A transfer time of 23.8 yrs results for this scenario requiring about 450 kg Xe for the SEP stage, jettisoned at 3 AU. We interpret the SEP/REP propulsion as a competing alternative to solar sail and ballistic/REP propulsion. Omiting a Jupiter fly-by even allows more launch flexibility, leaving the mission duration in the range of the ESA specification.},
  language  = {en}
}
@article{SchwagerFleschSchwarzboezletal.2022,
  author    = {Schwager, Christian and Flesch, Robert and Schwarzb{\"o}zl, Peter and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e}},
  title     = {Advanced two phase flow model for transient molten salt receiver system simulation},
  series = {Solar Energy},
  volume    = {232},
  journal   = {Solar Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0038-092X (print)},
  doi       = {10.1016/j.solener.2021.12.065},
  pages     = {362 -- 375},
  year      = {2022},
  abstract  = {In order to realistically predict and optimize the actual performance of a concentrating solar power (CSP) plant sophisticated simulation models and methods are required. This paper presents a detailed dynamic simulation model for a Molten Salt Solar Tower (MST) system, which is capable of simulating transient operation including detailed startup and shutdown procedures including drainage and refill. For appropriate representation of the transient behavior of the receiver as well as replication of local bulk and surface temperatures a discretized receiver model based on a novel homogeneous two-phase (2P) flow modelling approach is implemented in Modelica Dymola®. This allows for reasonable representation of the very different hydraulic and thermal properties of molten salt versus air as well as the transition between both. This dynamic 2P receiver model is embedded in a comprehensive one-dimensional model of a commercial scale MST system and coupled with a transient receiver flux density distribution from raytracing based heliostat field simulation. This enables for detailed process prediction with reasonable computational effort, while providing data such as local salt film and wall temperatures, realistic control behavior as well as net performance of the overall system. Besides a model description, this paper presents some results of a validation as well as the simulation of a complete startup procedure. Finally, a study on numerical simulation performance and grid dependencies is presented and discussed.},
  language  = {en}
}
@inproceedings{HandschuhStollenwerkBorchert2021,
  author    = {Handschuh, Nils and Stollenwerk, Dominik and Borchert, J{\"o}rg},
  title     = {Operation of thermal storage power plants under high renewable grid penetration},
  series = {NEIS 2021: Conference on Sustainable Energy Supply and Energy Storage Systems},
  booktitle = {NEIS 2021: Conference on Sustainable Energy Supply and Energy Storage Systems},
  publisher = {VDE Verlag},
  address   = {Berlin},
  isbn      = {978-3-8007-5651-3},
  pages     = {261 -- 265},
  year      = {2021},
  abstract  = {The planned coal phase-out in Germany by 2038 will lead to the dismantling of power plants with a total capacity of approx. 30 GW. A possible further use of these assets is the conversion of the power plants to thermal storage power plants; the use of these power plants on the day-ahead market is considerably limited by their technical parameters. In this paper, the influence of the technical boundary conditions on the operating times of these storage facilities is presented. For this purpose, the storage power plants were described as an MILP problem and two price curves, one from 2015 with a relatively low renewable penetration (33 \%) and one from 2020 with a high renewable energy penetration (51 \%) are compared. The operating times were examined as a function of the technical parameters and the critical influencing factors were investigated. The thermal storage power plant operation duration and the energy shifted with the price curve of 2020 increases by more than 25 \% compared to 2015.},
  language  = {en}
}
@inproceedings{QuitterMarinoBauschat2019,
  author    = {Quitter, Julius and Marino, Matthew and Bauschat, J.-Michael},
  title     = {Highly Non-Planar Aircraft Configurations: Estimation of Flight Mechanical Derivatives Using Low-Order Methods},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  pages     = {10 Seiten},
  year      = {2019},
  language  = {en}
}
@article{YoshinobuMiyamotoWerneretal.2017,
  author    = {Yoshinobu, Tatsuo and Miyamoto, Ko-ichiro and Werner, Frederik and Poghossian, Arshak and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Light-addressable potentiometric sensors for quantitative spatial imaging of chemical species},
  series = {Annual Review of Analytical Chemistry},
  volume    = {10},
  journal   = {Annual Review of Analytical Chemistry},
  publisher = {Annual Reviews},
  address   = {Palo Alto, Calif.},
  issn      = {1936-1327},
  doi       = {10.1146/annurev-anchem-061516-045158},
  pages     = {225 -- 246},
  year      = {2017},
  abstract  = {A light-addressable potentiometric sensor (LAPS) is a semiconductor-based chemical sensor, in which a measurement site on the sensing surface is defined by illumination. This light addressability can be applied to visualize the spatial distribution of pH or the concentration of a specific chemical species, with potential applications in the fields of chemistry, materials science, biology, and medicine. In this review, the features of this chemical imaging sensor technology are compared with those of other technologies. Instrumentation, principles of operation, and various measurement modes of chemical imaging sensor systems are described. The review discusses and summarizes state-of-the-art technologies, especially with regard to the spatial resolution and measurement speed; for example, a high spatial resolution in a submicron range and a readout speed in the range of several tens of thousands of pixels per second have been achieved with the LAPS. The possibility of combining this technology with microfluidic devices and other potential future developments are discussed.},
  language  = {en}
}
@misc{ArtmannLinderBayeretal.2017,
  author    = {Artmann, Gerhard and Linder, Peter and Bayer, Robin and Gossmann, Matthias},
  title     = {Celldrum electrode arrangement for measuring mechanical stress [Patent of invention]},
  publisher = {WIPO},
  address   = {Geneva},
  pages     = {18 Seiten},
  year      = {2017},
  abstract  = {The invention pertains to a CellDrum electrode arrangement for measuring mechanical stress, comprising a mechanical holder (1 ) and a non-conductive membrane (4), whereby the membrane (4) is at least partially fixed at its circumference to the mechanical holder (1), keeping it in place when the membrane (4) may bend due to forces acting on the membrane (4), the mechanical holder (1) and the membrane (4) forming a container, whereby the membrane (1) within the container comprises an cell- membrane compound layer or biological material (3) adhered to the deformable membrane 4 which in response to stimulation by an agent may exert mechanical stress to the membrane (4) such that the membrane bending stage changes whereby the container may be filled with an electrolyte, whereby an electric contact (2) is arranged allowing to contact said electrolyte when filled into to the container, whereby within a predefined geometry to the fixing of the membrane (4) an electrode (7) is arranged, whereby the electrode (7) is electrically insulated with respect to the electric contact (2) as well as said electrolyte, whereby mechanical stress due to an agent may be measured as a change in capacitance.},
  language  = {en}
}
@article{BaeckerPouyeshmanSchnitzleretal.2011,
  author    = {B{\"a}cker, Matthias and Pouyeshman, S. and Schnitzler, Thomas and Poghossian, Arshak and Wagner, Patrick and Biselli, Manfred and Sch{\"o}ning, Michael Josef},
  title     = {A silicon-based multi-sensor chip for monitoring of fermentation processes},
  series = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  journal   = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1862-6319},
  pages     = {1364 -- 1369},
  year      = {2011},
  language  = {en}
}
@article{LehnertzMormannOsterhageetal.2007,
  author    = {Lehnertz, Klaus and Mormann, Florian and Osterhage, Hannes and Andy, M{\"u}ller and Prusseit, Jens and Chernihovskyi, Anton and Staniek, Matth{\"a}us and Krug, Dieter and Bialonski, Stephan and Elger, Christian E.},
  title     = {State-of-the-art of seizure prediction},
  series = {Journal of Clinical Neurophysiology},
  volume    = {24},
  journal   = {Journal of Clinical Neurophysiology},
  number    = {2},
  issn      = {1537-1603},
  doi       = {10.1097/WNP.0b013e3180336f16},
  pages     = {147 -- 153},
  year      = {2007},
  language  = {en}
}
@inproceedings{LimpertSchifferFerrein2015,
  author    = {Limpert, Nicolas and Schiffer, Stefan and Ferrein, Alexander},
  title     = {A Local Planner for Ackermann-Driven Vehicles in ROS SBPL},
  series = {Proceedings of the International Conference on Pattern Recognition Association of South Africa and Robotics and Mechatronics (PRASA-RobMech), 2015},
  booktitle = {Proceedings of the International Conference on Pattern Recognition Association of South Africa and Robotics and Mechatronics (PRASA-RobMech), 2015},
  doi       = {10.1109/RoboMech.2015.7359518},
  pages     = {172 -- 177},
  year      = {2015},
  language  = {en}
}
@article{BhattaraiMayStaatetal.2022,
  author    = {Bhattarai, Aroj and May, Charlotte Anabell and Staat, Manfred and Kowalczyk, Wojciech and Tran, Thanh Ngoc},
  title     = {Layer-specific damage modeling of porcine large intestine under biaxial tension},
  series = {Bioengineering},
  volume    = {9},
  journal   = {Bioengineering},
  number    = {10, Early Access},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2306-5354},
  doi       = {10.3390/bioengineering9100528},
  pages     = {1 -- 17},
  year      = {2022},
  abstract  = {The mechanical behavior of the large intestine beyond the ultimate stress has never been investigated. Stretching beyond the ultimate stress may drastically impair the tissue microstructure, which consequently weakens its healthy state functions of absorption, temporary storage, and transportation for defecation. Due to closely similar microstructure and function with humans, biaxial tensile experiments on the porcine large intestine have been performed in this study. In this paper, we report hyperelastic characterization of the large intestine based on experiments in 102 specimens. We also report the theoretical analysis of the experimental results, including an exponential damage evolution function. The fracture energies and the threshold stresses are set as damage material parameters for the longitudinal muscular, the circumferential muscular and the submucosal collagenous layers. A biaxial tensile simulation of a linear brick element has been performed to validate the applicability of the estimated material parameters. The model successfully simulates the biomechanical response of the large intestine under physiological and non-physiological loads.},
  language  = {en}
}
@inproceedings{GoettenFinger2019,
  author    = {G{\"o}tten, Falk and Finger, Felix},
  title     = {Conceptual Design of a Modular 150 kg Vertical Take-off and Landing Unmanned Aerial Vehicle},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  pages     = {1 -- 10},
  year      = {2019},
  language  = {en}
}
@article{WolfSchlickSpringer1997,
  author    = {Wolf, Martin R. and Schlick, Christopher and Springer, J.},
  title     = {The use of implicit communication mechanisms in desktop-teleconferencing-systems},
  series = {Proceedings of WWDU '97 Tokyo, Fifth International Scientific Conference on Work with Display Units : November 3 - 5, 1997, Tokyo},
  journal   = {Proceedings of WWDU '97 Tokyo, Fifth International Scientific Conference on Work with Display Units : November 3 - 5, 1997, Tokyo},
  editor    = {Miyamoto, Hiroyuki},
  publisher = {-},
  address   = {Tokyo},
  pages     = {193 -- 194},
  year      = {1997},
  language  = {en}
}
@article{KnobeGiesenPlateetal.2016,
  author    = {Knobe, M. and Giesen, M. and Plate, S. and Gradl-Dietsch, G. and Buecking, B. and Eschbach, D. and Laack, Walter van and Pape, H.-C.},
  title     = {The Aachen mobility and balance index to measure physiological falls risk: a comparison with the Tinetti POMA scale},
  series = {European Journal Of Trauma And Emergency Surgery},
  volume    = {42},
  journal   = {European Journal Of Trauma And Emergency Surgery},
  number    = {5},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1863-9941},
  doi       = {10.1007/s00068-016-0693-2},
  pages     = {537 -- 545},
  year      = {2016},
  abstract  = {Purpose The most commonly used mobility assessments for screening risk of falls among older adults are rating scales such as the Tinetti performance oriented mobility assessment (POMA). However, its correlation with falls is not always predictable and disadvantages of the scale include difficulty to assess many of the items on a 3-point scale and poor specificity. The purpose of this study was to describe the ability of the new Aachen Mobility and Balance Index (AMBI) to discriminate between subjects with a fall history and subjects without such events in comparison to the Tinetti POMA Scale. Methods For this prospective cohort study, 24 participants in the study group and 10 in the control group were selected from a population of patients in our hospital who had met the stringent inclusion criteria. Both groups completed the Tinetti POMA Scale (gait and balance component) and the AMBI (tandem stance, tandem walk, ten-meter-walk-test, sit-to-stand with five repetitions, 360° turns, timed-up-and-go-test and measurement of the dominant hand grip strength). A history of falls and hospitalization in the past year were evaluated retrospectively. The relationships among the mobility tests were examined with Bland-Altmananalysis. Receiver-operated characteristics curves, sensitivity and specificity were calculated. Results The study showed a strong negative correlation between the AMBI (17 points max., highest fall risk) and Tinetti POMA Scale (28 points max., lowest fall risk; r = -0.78, p < 0.001) with an excellent discrimination between community-dwelling older people and a younger control group. However, there were no differences in any of the mobility and balance measurements between participants with and without a fall history with equal characteristics in test comparison (AMBI vs. Tinetti POMA Scale: AUC 0.570 vs. 0.598; p = 0.762). The Tinetti POMA Scale (cut-off <20 points) showed a sensitivity of 0.45 and a specificity of 0.69, the AMBI a sensitivity of 0.64 and a specificity of 0.46 (cut-off >5 points). Conclusion The AMBI comprises mobility and balance tasks with increasing difficulty as well as a measurement of the dominant hand-grip strength. Its ability to identify fallers was comparable to the Tinetti POMA Scale. However, both measurement sets showed shortcomings in discrimination between fallers and non-fallers based on a self-reported retrospective falls-status.},
  language  = {en}
}
@article{AlKaidyKuthanHeringetal.2016,
  author    = {Al-Kaidy, Huschyar and Kuthan, Kai and Hering, Thomas and Tippk{\"o}tter, Nils},
  title     = {Aqueous droplets used as enzymatic microreactors and their electromagnetic actuation},
  series = {Journal of Visualized Experiments},
  journal   = {Journal of Visualized Experiments},
  number    = {Issue 126},
  issn      = {1940-087X},
  doi       = {10.3791/54643},
  year      = {2016},
  abstract  = {For the successful implementation of microfluidic reaction systems, such as PCR and electrophoresis, the movement of small liquid volumes is essential. In conventional lab-on-a-chip-platforms, solvents and samples are passed through defined microfluidic channels with complex flow control installations. The droplet actuation platform presented here is a promising alternative. With it, it is possible to move a liquid drop (microreactor) on a planar surface of a reaction platform (lab-in-a-drop). The actuation of microreactors on the hydrophobic surface of the platform is based on the use of magnetic forces acting on the outer shell of the liquid drops which is made of a thin layer of superhydrophobic magnetite particles. The hydrophobic surface of the platform is needed to avoid any contact between the liquid core and the surface to allow a smooth movement of the microreactor. On the platform, one or more microreactors with volumes of 10 µL can be positioned and moved simultaneously. The platform itself consists of a 3 x 3 matrix of electrical double coils which accommodate either neodymium or iron cores. The magnetic field gradients are automatically controlled. By variation of the magnetic field gradients, the microreactors' magnetic hydrophobic shell can be manipulated automatically to move the microreactor or open the shell reversibly. Reactions of substrates and corresponding enzymes can be initiated by merging the microreactors or bringing them into contact with surface immobilized catalysts.},
  language  = {en}
}
@article{AbouzarPoghossianPedrazaetal.2011,
  author    = {Abouzar, Maryam H. and Poghossian, Arshak and Pedraza, A. M. and Gandhi, D. and Ingebrandt, S. and Moritz, W. and Sch{\"o}ning, Michael Josef},
  title     = {An array of field-effect nanoplate SOI capacitors for (bio-)chemical sensing},
  series = {Biosensors and Bioelectronics. 26 (2011), H. 6},
  journal   = {Biosensors and Bioelectronics. 26 (2011), H. 6},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0956-5663},
  pages     = {3023 -- 3028},
  year      = {2011},
  language  = {en}
}
@article{HeuermannHoltrup2009,
  author    = {Heuermann, Holger and Holtrup, Stephan},
  title     = {Fundamentals and ignition of a microplasma at 2.45 GHZ / Holtrup, Stephan ; Heuermann, Holger},
  series = {European Microwave Conference, 2009 : EuMC 2009 ; Sept. 29, 2009 - Oct. 1, 2009, Rome, Italy ; part of European Microwave Week (EuMW) / sponsored by EuMA, European Microwave Association ... Endorsed by IEEE},
  journal   = {European Microwave Conference, 2009 : EuMC 2009 ; Sept. 29, 2009 - Oct. 1, 2009, Rome, Italy ; part of European Microwave Week (EuMW) / sponsored by EuMA, European Microwave Association ... Endorsed by IEEE},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  isbn      = {978-1-4244-4748-0},
  pages     = {1607 -- 1609},
  year      = {2009},
  language  = {en}
}
@article{KurulganDemirciLinderDemircietal.2009,
  author    = {Kurulgan Demirci, Eylem and Linder, Peter and Demirci, Taylan and Trzewik, J{\"u}rgen and Digel, Ilya and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Contractile tension of endothelial cells: An LPS based in-vitro sepsis model},
  series = {IUBMB Life. 61 (2009), H. 3},
  journal   = {IUBMB Life. 61 (2009), H. 3},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1521-6543},
  pages     = {307 -- 308},
  year      = {2009},
  language  = {en}
}
@article{PoghossianCherstvySchoening2004,
  author    = {Poghossian, Arshak and Cherstvy, A. and Sch{\"o}ning, Michael Josef},
  title     = {Possibilities and limitations of label-free detection of DNA hybridization with field-effect based devices},
  series = {Digest of technical papers : September 12 - 15, 2004, Rome, Italy, Pontificia Universitas Sancto Thoma Aquinate in Urbe / [conference chairperson: C. Di Natale].},
  journal   = {Digest of technical papers : September 12 - 15, 2004, Rome, Italy, Pontificia Universitas Sancto Thoma Aquinate in Urbe / [conference chairperson: C. Di Natale].},
  address   = {Roma},
  isbn      = {88-7621-282-5},
  pages     = {173 -- 176},
  year      = {2004},
  language  = {en}
}
@article{PhamStaat2014,
  author    = {Pham, Phu Tinh and Staat, Manfred},
  title     = {FEM-based shakedown analysis of hardening structures},
  series = {Asia Pacific journal on computational engineering},
  journal   = {Asia Pacific journal on computational engineering},
  number    = {1},
  publisher = {SpringerOpen},
  address   = {Berlin},
  issn      = {2196-1166 (E-Journal)},
  doi       = {10.1186/2196-1166-1-4},
  pages     = {Article No. 4},
  year      = {2014},
  abstract  = {This paper develops a new finite element method (FEM)-based upper bound algorithm for limit and shakedown analysis of hardening structures by a direct plasticity method. The hardening model is a simple two-surface model of plasticity with a fixed bounding surface. The initial yield surface can translate inside the bounding surface, and it is bounded by one of the two equivalent conditions: (1) it always stays inside the bounding surface or (2) its centre cannot move outside the back-stress surface. The algorithm gives an effective tool to analyze the problems with a very high number of degree of freedom. Our numerical results are very close to the analytical solutions and numerical solutions in literature.},
  language  = {en}
}
@article{SiqueiraMakiPaulovichetal.2010,
  author    = {Siqueira, Jose R. and Maki, Rafael M. and Paulovich, Fernando V. and Werner, Frederik and Poghossian, Arshak and Oliveira, Maria C. F. de and Zucolotto, Valtencir and Oliveira, Osvaldo N. Jr. and Sch{\"o}ning, Michael Josef},
  title     = {Use of Information Visualization Methods Eliminating Cross Talk in Multiple Sensing Units Investigated for a Light-Addressable Potentiometric Sensor},
  series = {Analytical Chemistry (2010)},
  journal   = {Analytical Chemistry (2010)},
  isbn      = {0003-2700},
  pages     = {61 -- 65},
  year      = {2010},
  language  = {en}
}
@article{JablonowskiKollmannNabeletal.2016,
  author    = {Jablonowski, Nicolai David and Kollmann, Tobias and Nabel, Moritz and Damm, Tatjana and Klose, Holger and M{\"u}ller, Michael and Bl{\"a}sing, Marc and Seebold, S{\"o}ren and Krafft, Simone and Kuperjans, Isabel and Dahmen, Markus and Schurr, Ulrich},
  title     = {Valorization of Sida (Sida hermaphrodita) biomass for multiple energy purposes},
  series = {GCB [Global Change Biology] Bioenergy},
  volume    = {9},
  journal   = {GCB [Global Change Biology] Bioenergy},
  number    = {1},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1757-1707 (online)},
  doi       = {10.1111/gcbb.12346},
  pages     = {202 -- 214},
  year      = {2016},
  abstract  = {The performance and biomass yield of the perennial energy plant Sida hermaphrodita (hereafter referred to as Sida) as a feedstock for biogas and solid fuel was evaluated throughout one entire growing period at agricultural field conditions. A Sida plant development code was established to allow comparison of the plant growth stages and biomass composition. Four scenarios were evaluated to determine the use of Sida biomass with regard to plant development and harvest time: (i) one harvest for solid fuel only; (ii) one harvest for biogas production only; (iii) one harvest for biogas production, followed by a harvest of the regrown biomass for solid fuel; and (iv) two consecutive harvests for biogas production. To determine Sida's value as a feedstock for combustion, we assessed the caloric value, the ash quality, and melting point with regard to DIN EN ISO norms. The results showed highest total dry biomass yields of max. 25 t ha⁻¹, whereas the highest dry matter of 70\% to 80\% was obtained at the end of the growing period. Scenario (i) clearly indicated the highest energy recovery, accounting for 439 288 MJ ha⁻¹; the energy recovery of the four scenarios from highest to lowest followed this order: (i) ≫ (iii) ≫ (iv) > (ii). Analysis of the Sida ashes showed a high melting point of >1500 °C, associated with a net calorific value of 16.5-17.2 MJ kg⁻¹. All prerequisites for DIN EN ISO norms were achieved, indicating Sida's advantage as a solid energy carrier without any post-treatment after harvesting. Cell wall analysis of the stems showed a constant lignin content after sampling week 16 (July), whereas cellulose had already reached a plateau in sampling week 4 (April). The results highlight Sida as a promising woody, perennial plant, providing biomass for flexible and multipurpose energy applications.},
  language  = {en}
}
@article{HaagZontarSchleupenetal.2014,
  author    = {Haag, S. and Zontar, D. and Schleupen, Josef and M{\"u}ller, T. and Brecher, C.},
  title     = {Chain of refined perception in self-optimizing assembly of micro-optical systems},
  series = {Journal of sensors and sensor systems},
  volume    = {3},
  journal   = {Journal of sensors and sensor systems},
  number    = {1},
  publisher = {Copernicus Publ.},
  address   = {G{\"o}ttingen},
  issn      = {2194-878X},
  doi       = {10.5194/jsss-3-87-2014},
  pages     = {87 -- 95},
  year      = {2014},
  abstract  = {Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements - especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base.},
  language  = {en}
}
@article{HeinzeMangPopescuetal.2016,
  author    = {Heinze, D. and Mang, Thomas and Popescu, C. and Weichold, O.},
  title     = {Effect of side chain length and degree of polymerization on the decomposition and crystallization behaviour of chlorinated poly(vinyl ester) oligomers},
  series = {Thermochimica Acta},
  volume    = {637},
  journal   = {Thermochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0040-6031 (electronic)},
  doi       = {10.1016/j.tca.2016.05.015},
  pages     = {143 -- 153},
  year      = {2016},
  abstract  = {Four members of a homologous series of chlorinated poly(vinyl ester) oligomers CCl₃-(CH₂CH (OCO(CH₂)ₘCH₃))ₙ-Cl with degrees of polymerization of 10 and 20 were prepared by telomerisation using carbon tetrachloride. The number of side chain carbon atoms ranges from 2 (poly(vinyl acetate) to 18 (poly(vinyl stearate)). The effect of the n-alkyl side chain length and of the degree of polymerization on the thermal stability and crystallization behaviour of the synthesized compounds was investigated. All oligomers degrade in two major steps by first losing HCl and side chains with subsequent breakdown of the backbone. The members with short side chains, up to poly(vinyl octanoate), are amorphous and show internal plasticization, whereas those with high number of side chain carbon atoms are semi-crystalline due to side-chain crystallization. A better packing for poly(vinyl stearate) is also noticeable. The glass transition and melting temperatures as well as the onset temperature of decomposition are influenced to a larger extent by the side chain length than by the degree of polymerization. Thermal stability is improved if both the size and number of side chains increase, but only a long side chain causes a significant increase of the resistance to degradation. This results in a stabilization of PVAc so that oligomers from poly(vinyl octanoate) on are stable under atmospheric conditions. Thus, the way to design stable, chlorinated PVEs oligomers is to use a long n-alkyl side chain.},
  language  = {en}
}
@phdthesis{Schusser2015,
  author    = {Schusser, Sebastian},
  title     = {Sensor-based degradation monitoring for the evaluation of (bio)degradable polymers},
  publisher = {Universiteit Hasselt ; FH Aachen},
  address   = {Hasselt ; Aachen},
  pages     = {145 Seiten},
  year      = {2015},
  language  = {en}
}
@article{RieperGebhardtStucker2016,
  author    = {Rieper, Harald and Gebhardt, Andreas and Stucker, Brent},
  title     = {Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt \% Cu},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {13},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/nbn:de:0009-2-44141},
  year      = {2016},
  abstract  = {The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. \% Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time.},
  language  = {en}
}