@inproceedings{KernBraun2014,
  author    = {Kern, Alexander and Braun, Christian},
  title     = {Risk management according to IEC 62305-2 edition 2: 2010-12 assessment of structures with a risk of explosion},
  series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  organization    = {International Conference on Lightning Protection <2014, Shanghai>},
  pages     = {1237 -- 1242},
  year      = {2014},
  abstract  = {Risk management for structures with a risk of explosion should be considered very carefully when performing a risk analysis according to IEC 62305-2. In contrast to the 2006 edition of the standard, the 2010 edition describes the topic "Structures with a risk of explosion" in more detail. Moreover, in Germany separate procedures and parameters are defined for the risk analysis of structures with a risk of explosion (Supplement 3 of the German DIN EN 62305-2 standard). This paper describes the contents and the relevant calculations of this Supplement 3, together with a numerical example.},
  language  = {en}
}
@article{GuoSekiMiyamotoetal.2014,
  author    = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor with a novel photoexcitation method for a higher spatial resolution},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.369},
  pages     = {456 -- 459},
  year      = {2014},
  abstract  = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) realized a higher spatial resolution of chemical imaging. In this method, a modulated light probe, which generates the alternating photocurrent signal, is surrounded by a ring of constant light, which suppresses the lateral diffusion of photocarriers by enhancing recombination. A device simulation verified that a higher spatial resolution could be obtained by adjusting the gap between the modulated and constant light. It was also found that a higher intensity and a longer wavelength of constant light was more effective. However, there exists a tradeoff between the spatial resolution and the amplitude of the photocurrent, and thus, the signal-to-noise ratio. A tilted incidence of constant light was applied, which could achieve even higher resolution with a smaller loss of photocurrent.},
  language  = {en}
}
@article{MiyamotoSekiWagneretal.2014,
  author    = {Miyamoto, K. and Seki, K. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Enhancement of the spatial resolution of the chemical imaging sensor by a hybrid fiber-optic illumination},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.563},
  pages     = {612 -- 615},
  year      = {2014},
  abstract  = {The chemical imaging sensor, which is based on the principle of the light-addressable potentiometric sensor (LAPS), is a powerful tool to visualize the spatial distribution of chemical species on the sensor surface. The spatial resolution of this sensor depends on the diffusion of photocarriers excited by a modulated light. In this study, a novel hybrid fiber-optic illumination was developed to enhance the spatial resolution. It consists of a modulated light probe to generate a photocurrent signal and a ring of constant light, which suppresses the lateral diffusion of minority carriers excited by the modulated light. It is demonstrated that the spatial resolution was improved from 92 μm to 68 μm.},
  language  = {en}
}
@article{BronderWuPoghossianetal.2014,
  author    = {Bronder, Thomas and Wu, Chunsheng and Poghossian, Arshak and Werner, Frederik and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Label-free detection of DNA hybridization with light-addressable potentiometric sensors: comparison of various DNA-immobilization strategies},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.647},
  pages     = {755 -- 758},
  year      = {2014},
  abstract  = {Light-addressable potentiometric sensors (LAPS) consisting of a p-Si-SiO2 and p-Si-SiO2-Au structure, respectively, have been tested for a label-free electrical detection of DNA (deoxyribonucleic acid) hybridization. Three different strategies for immobilizing single-stranded probe DNA (ssDNA) molecules on a LAPS surface have been studied and compared: (a) immobilization of thiol-modified ssDNA on the patterned Au surface via gold-thiol bond, (b) covalent immobilization of amino-modified ssDNA onto the SiO2 surface functionalized with 3-aminopropyltriethoxysilane and (c) layer-by-layer adsorption of negatively charged ssDNA on a positively charged weak polyelectrolyte layer of poly(allylamine hydrochloride).},
  language  = {en}
}
@article{HuckPoghossianBaeckeretal.2014,
  author    = {Huck, Christina and Poghossian, Arshak and B{\"a}cker, Matthias and Reisert, Steffen and Schubert, J. and Zander, W. and Begoyan, V. K. and Buniatyan, V. V. and Sch{\"o}ning, Michael Josef},
  title     = {Chemical sensors based on a high-k perovskite oxide of barium strontium titanate},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.258},
  pages     = {28 -- 31},
  year      = {2014},
  abstract  = {High-k perovskite oxide of barium strontium titanate (BST) represents a very attractive multi-functional transducer material for the development of (bio-)chemical sensors for liquids. In this work, BST films have been applied as a sensitive transducer material for a label-free detection of adsorbed charged macromolecules (positively charged polyelectrolytes) and concentration of hydrogen peroxide vapor as well as protection insulator layer for a contactless electrolyte-conductivity sensor. The experimental results of characterization of individual sensors are presented. Special emphasis is devoted towards the development of a capacitively-coupled contactless electrolyte-conductivity sensor.},
  language  = {en}
}
@article{SchusserBaeckerKrischeretal.2014,
  author    = {Schusser, Sebastian and B{\"a}cker, Matthias and Krischer, M. and Wenzel, L. and Leinhos, Marcel and Poghossian, Arshak and Biselli, Manfred and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Enzymatically catalyzed degradation of biodegradable polymers investigated by means of a semiconductor-based field-effect sensor},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.689},
  pages     = {1314 -- 1317},
  year      = {2014},
  abstract  = {A semiconductor field-effect device has been used for an enzymatically catalyzed degradation of biopolymers for the first time. This novel technique is capable to monitor the degradation process of multiple samples in situ and in real-time. As model system, the degradation of the biopolymer poly(D, L-lactic acid) has been monitored in the degradation medium containing the enzyme lipase from Rhizomucor miehei. The obtained results demonstrate the potential of capacitive field-effect sensors for degradation studies of biodegradable polymers.},
  language  = {en}
}
@misc{NoetzoldBragardFinketal.2014,
  author    = {N{\"o}tzold, K. and Bragard, Michael and Fink, K. and Griessel, R. and Wegener, R.},
  title     = {Cascaded H-bridge converter with transformer based cell power balancing in each voltage level : [Patentschrift]},
  publisher = {Europ{\"a}isches Patentamt / United States Patent and Trademark Office [u.a.]},
  address   = {Den Haag / Alexandria, VA},
  pages     = {16 S. : graph. Darst.},
  year      = {2014},
  language  = {en}
}
@article{Stulpe2014,
  author    = {Stulpe, Werner},
  title     = {From the attempt of certain classical reformulations of quantum mechanics to quasi-probability representations},
  series = {Journal of Mathematical Physics},
  volume    = {55},
  journal   = {Journal of Mathematical Physics},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {College Park, Md.},
  issn      = {222-488},
  doi       = {10.1063/1.4861939},
  pages     = {Artikel 012109},
  year      = {2014},
  abstract  = {The concept of an injective affine embedding of the quantum states into a set of classical states, i.e., into the set of the probability measures on some measurable space, as well as its relation to statistically complete observables is revisited, and its limitation in view of a classical reformulation of the statistical scheme of quantum mechanics is discussed. In particular, on the basis of a theorem concerning a non-denseness property of a set of coexistent effects, it is shown that an injective classical embedding of the quantum states cannot be supplemented by an at least approximate classical description of the quantum mechanical effects. As an alternative approach, the concept of quasi-probability representations of quantum mechanics is considered.},
  language  = {en}
}
@article{DachwaldMikuckiTulaczyketal.2014,
  author    = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng},
  title     = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems},
  series = {Annals of Glaciology},
  volume    = {55},
  journal   = {Annals of Glaciology},
  number    = {65},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  issn      = {1727-5644},
  doi       = {10.3189/2014AoG65A004},
  pages     = {14 -- 22},
  year      = {2014},
  abstract  = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.},
  language  = {en}
}
@article{LevesqueSiegwolfEilmannetal.2014,
  author    = {L{\´e}vesque, Mathieu and Siegwolf, Rolf and Eilmann, Britta and Saurer, Matthias and Rigling, Andreas},
  title     = {Increased water-use efficiency does not lead to enhanced tree growth under xeric and mesic conditions},
  series = {New Phytologist},
  volume    = {203},
  journal   = {New Phytologist},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1469-8137 (Online)},
  doi       = {10.1111/nph.12772},
  pages     = {94 -- 109},
  year      = {2014},
  language  = {en}
}
@inproceedings{NeumannFerreinKallweitetal.2014,
  author    = {Neumann, Tobias and Ferrein, Alexander and Kallweit, Stephan and Scholl, Ingrid},
  title     = {Towards a mobile mapping robot for underground mines},
  series = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town},
  booktitle = {7th Conference of Robotics and Mechatronics : RobMech 2014 : 27th and 28th Nov. 2014, Cape Town},
  organization    = {Conference of Robotics and Mechatronics <7, 2014, Cape Town, South Africa>},
  pages     = {1 -- 6},
  year      = {2014},
  language  = {en}
}
@incollection{AlhwarinFerreinScholl2014,
  author    = {Alhwarin, Faraj and Ferrein, Alexander and Scholl, Ingrid},
  title     = {IR stereo kinect: improving depth images by combining structured light with IR stereo},
  series = {PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862)},
  booktitle = {PRICAI 2014: Trends in artificial intelligence : 13th Pacific Rim International Conference on Artificial Intelligence : Gold Coast, QLD, Australia, December 1-5, 2014 : proceedings. (Lecture notes in computer science ; vol. 8862)},
  publisher = {Springer},
  address   = {M{\"u}nchen},
  isbn      = {978-3-319-13559-5 (Print) ; 978-3-319-13560-1 (E-Book)},
  doi       = {10.1007/978-3-319-13560-1_33},
  pages     = {409 -- 421},
  year      = {2014},
  abstract  = {RGB-D sensors such as the Microsoft Kinect or the Asus Xtion are inexpensive 3D sensors. A depth image is computed by calculating the distortion of a known infrared light (IR) pattern which is projected into the scene. While these sensors are great devices they have some limitations. The distance they can measure is limited and they suffer from reflection problems on transparent, shiny, or very matte and absorbing objects. If more than one RGB-D camera is used the IR patterns interfere with each other. This results in a massive loss of depth information. In this paper, we present a simple and powerful method to overcome these problems. We propose a stereo RGB-D camera system which uses the pros of RGB-D cameras and combine them with the pros of stereo camera systems. The idea is to utilize the IR images of each two sensors as a stereo pair to generate a depth map. The IR patterns emitted by IR projectors are exploited here to enhance the dense stereo matching even if the observed objects or surfaces are texture-less or transparent. The resulting disparity map is then fused with the depth map offered by the RGB-D sensor to fill the regions and the holes that appear because of interference, or due to transparent or reflective objects. Our results show that the density of depth information is increased especially for transparent, shiny or matte objects.},
  language  = {en}
}
@inproceedings{FateriGebhardt2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Jewelry fabrication via selective laser melting of glass},
  series = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  booktitle = {ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications},
  isbn      = {978-0-7918-4583-7},
  doi       = {10.1115/ESDA2014-20380},
  pages     = {V001T06A005},
  year      = {2014},
  abstract  = {Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies applicable for producing complex geometries which are typically expensive or difficult to fabricate using conventional methods. This process has been extensively investigated experimentally for various metals and the fabrication process parameters have been established for different applications; however, fabricating 3D glass objects using SLM technology has remained a challenge so far although it could have many applications. This paper presents a summery on various experimental evaluations of a material database incorporating the build parameters of glass powder using the SLM process for jewelry applications.},
  language  = {en}
}
@inproceedings{GebhardtRitzSiekmannetal.2014,
  author    = {Gebhardt, Andreas and Ritz, Thomas and Siekmann, Kirsten and Wallenborn, Ramona},
  title     = {Additive manufacturing businesses in the process chain of individualized mass products},
  series = {DDMC 2014 : Proceedings of the Fraunhofer Direct Digital Manufacturing Conference},
  booktitle = {DDMC 2014 : Proceedings of the Fraunhofer Direct Digital Manufacturing Conference},
  editor    = {Demmer, Axel},
  publisher = {Fraunhofer},
  address   = {Stuttgart},
  isbn      = {978-3-8396-9128-1 (E-Book)},
  year      = {2014},
  language  = {en}
}
@inproceedings{RitzIzquierdoTelloDamm2014,
  author    = {Ritz, Thomas and Izquierdo Tello, C{\´e}sar and Damm, Sebastian},
  title     = {Connecting a pedelec to the cloud as basis for gamification in multi modal mobility planning},
  series = {MobileCloud 2014 : 2nd IEEE International Conference on Mobile Cloud Computing, Services, and Engineering Oxford, United Kingdom 7-10 April 2014},
  booktitle = {MobileCloud 2014 : 2nd IEEE International Conference on Mobile Cloud Computing, Services, and Engineering Oxford, United Kingdom 7-10 April 2014},
  publisher = {IEEE Service Center},
  address   = {Piscataway, NJ},
  isbn      = {978-1-4799-2504-9},
  doi       = {10.1109/MobileCloud.2014.25},
  pages     = {101 -- 108},
  year      = {2014},
  language  = {en}
}
@inproceedings{HeuermannFinger2014,
  author    = {Heuermann, Holger and Finger, Torsten},
  title     = {2.45 GHz Plasma Powered Spark Plug by Thermal and EM-Optimization},
  pages     = {30 Folien},
  year      = {2014},
  language  = {en}
}
@article{RaueWambachGloeggleretal.2014,
  author    = {Raue, Markus and Wambach, M. and Gl{\"o}ggler, S. and Grefen, Dana and Kaufmann, R. and Abetz, C. and Georgopanos, P. and Handge, U. A. and Mang, Thomas and Bl{\"u}mich, B. and Abetz, V.},
  title     = {Investigation of historical hard rubber ornaments of Charles Goodyear},
  series = {Macromolecular chemistry and physics},
  volume    = {Vol. 215},
  journal   = {Macromolecular chemistry and physics},
  number    = {No. 3},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1022-1352},
  pages     = {245 -- 254},
  year      = {2014},
  language  = {en}
}
@inproceedings{SchoppHeuermannHoltrup2014,
  author    = {Schopp, Christoph and Heuermann, Holger and Holtrup, S.},
  title     = {Investigation on efficacy optimization of RF-driven automotive D-lamps},
  series = {44th European Microwave Conference (EuMC),2014, Rome},
  booktitle = {44th European Microwave Conference (EuMC),2014, Rome},
  doi       = {10.1109/EuMC.2014.6986645},
  pages     = {1154 -- 1157},
  year      = {2014},
  language  = {en}
}
@incollection{HeuermannFinger2014,
  author    = {Heuermann, Holger and Finger, Torsten},
  title     = {Microwave Spark Plug for Very High-Pressure Conditions},
  series = {Ignition systems for gasoline engines},
  booktitle = {Ignition systems for gasoline engines},
  editor    = {G{\"u}nther, Michael},
  publisher = {DCM Druck},
  address   = {Meckenheim},
  pages     = {269 -- 282},
  year      = {2014},
  language  = {en}
}
@article{HafnerDemetzWeickertetal.2014,
  author    = {Hafner, David and Demetz, Oliver and Weickert, Joachim and Reißel, Martin},
  title     = {Mathematical Foundations and Generalisations of the Census Transform for Robust Optic Flow Computation},
  series = {Journal of Mathematical Imaging and Vision},
  journal   = {Journal of Mathematical Imaging and Vision},
  publisher = {Springer},
  address   = {New York},
  issn      = {1573-7683 (Online)},
  doi       = {10.1007/s10851-014-0529-9},
  year      = {2014},
  language  = {en}
}
@article{FredebeulKreinSteingroever2014,
  author    = {Fredebeul-Krein, Markus and Steingr{\"o}ver, Markus},
  title     = {Wholesale broadband access to IPTV in an NGA environment : how to deal with it from a regulatory perspective?},
  series = {Telecommunications Policy},
  volume    = {38},
  journal   = {Telecommunications Policy},
  number    = {3},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0308-5961 (Print)},
  doi       = {doi:10.1016/j.telpol.2013.04.002},
  pages     = {264 -- 277},
  year      = {2014},
  language  = {en}
}
@inproceedings{Huening2014,
  author    = {H{\"u}ning, Felix},
  title     = {Power semiconductors : key components for HEV/EV},
  series = {FISITA 2014 World Automotive Congress : 2 - 6 June, Maastricht, the Netherlands International Federation of Automotive Engineering Societies},
  booktitle = {FISITA 2014 World Automotive Congress : 2 - 6 June, Maastricht, the Netherlands International Federation of Automotive Engineering Societies},
  publisher = {KIVI},
  address   = {[s.l.]},
  pages     = {1 USB-Speicherstick},
  year      = {2014},
  language  = {en}
}
@inproceedings{JanotteFecklerKoetteretal.2014,
  author    = {Janotte, N. and Feckler, G. and K{\"o}tter, Jens and Decker, Stefan and Herrmann, Ulf and Schmitz, Mark and L{\"u}pfert, E.},
  title     = {Dynamic performance evaluation of the HelioTrough® collector demonstration loop : towards a new benchmark in parabolic trough qualification},
  series = {SolarPACES International Conference 2013, Las Vegas, Nevada, USA, 17 - 20 September 2013 : [proceedings]. - Pt. 1. - (Energy procedia ; 49)},
  booktitle = {SolarPACES International Conference 2013, Las Vegas, Nevada, USA, 17 - 20 September 2013 : [proceedings]. - Pt. 1. - (Energy procedia ; 49)},
  publisher = {Curran},
  address   = {Red Hook, NY},
  isbn      = {978-1-63266-904-9},
  issn      = {1876-6102},
  doi       = {10.1016/j.egypro.2014.03.012},
  pages     = {109 -- 117},
  year      = {2014},
  language  = {en}
}
@article{MartinGonzalezKotliarRiosMartinezetal.2014,
  author    = {Martin-Gonzalez, Anabel and Kotliar, Konstantin and Rios-Martinez, Jorge and Lanzl, Ines and Navab, Nassir},
  title     = {Mediated-reality magnification for macular degeneration rehabilitation},
  series = {Journal of Modern Optics},
  volume    = {61},
  journal   = {Journal of Modern Optics},
  number    = {17},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1362-3044},
  doi       = {10.1080/09500340.2014.936110},
  pages     = {1400 -- 1408},
  year      = {2014},
  language  = {en}
}
@inproceedings{LenzWolf2014,
  author    = {Lenz, Laura L. and Wolf, Martin},
  title     = {Economic evaluation of serious games with the comparative assessment framework COSEGA},
  series = {The shift from teaching to learning : individual, collective and organizational learning through gaming simulation ; proceedings of the 45th conference of the International Simulation and Gaming Association, Dornbirn 2014},
  booktitle = {The shift from teaching to learning : individual, collective and organizational learning through gaming simulation ; proceedings of the 45th conference of the International Simulation and Gaming Association, Dornbirn 2014},
  editor    = {Kritz, Willy Christian},
  publisher = {Bertelsmann},
  address   = {[Bielefeld]},
  isbn      = {978-3-7639-5422-3},
  pages     = {374 -- 386},
  year      = {2014},
  language  = {en}
}
@article{VogtMottaghyRathetal.2014,
  author    = {Vogt, C. and Mottaghy, Darius and Rath, V. and Marquart, G. and Dijkshoorn, L. and Wolf, A. and Clauser, C.},
  title     = {Vertical variation in heat flow on the Kola Peninsula: palaeoclimate or fluid flow?},
  series = {Geophysical Journal International},
  volume    = {199},
  journal   = {Geophysical Journal International},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1365-246X},
  doi       = {10.1093/gji/ggu282},
  pages     = {829 -- 843},
  year      = {2014},
  abstract  = {Following earlier studies, we present forward and inverse simulations of heat and fluid transport of the upper crust using a local 3-D model of the Kola area. We provide best estimates for palaeotemperatures and permeabilities, their errors and their dependencies. Our results allow discriminating between the two mentioned processes to a certain extent, partly resolving the non-uniqueness of the problem. We find clear indications for a significant contribution of advective heat transport, which, in turn, imply only slightly lower ground surface temperatures during the last glacial maximum relative to the present value. These findings are consistent with the general background knowledge of (i) the fracture zones and the corresponding fluid movements in the bedrock and (ii) the glacial history of the Kola area.},
  language  = {en}
}
@inproceedings{KirschFelberMarcheretal.2014,
  author    = {Kirsch, Ansgar and Felber, W. and Marcher, Thomas and Fuchs, W.},
  title     = {Geotechnical challenges during design and construction of a ski resort in Azerbaijan},
  series = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria},
  booktitle = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria},
  publisher = {{\"O}IAV - {\"O}sterreichischer Ingenieur- und Architekten-Verein},
  address   = {Wien},
  organization    = {Danube - European Conference on Geotechnical Engineering <15, 2014, Wien>},
  isbn      = {978-3-902593-01-6},
  pages     = {757 -- 762},
  year      = {2014},
  language  = {en}
}
@incollection{AltayTaddeiButenwegetal.2014,
  author    = {Altay, Okyay and Taddei, Francesca and Butenweg, Christoph and Klinkel, Sven},
  title     = {Vibration mitigation of wind turbine towers with tuned mass dampers},
  series = {Wind turbine control and monitoring. (Advances in industrial control)},
  booktitle = {Wind turbine control and monitoring. (Advances in industrial control)},
  publisher = {Springer},
  address   = {Cham ; Heidelberg ; New York ; Dordrecht ; London},
  isbn      = {978-3-319-08412-1 (Print) ; 978-3-319-08413-8 (E-Book)},
  doi       = {10.1007/978-3-319-08413-8_12},
  pages     = {337 -- 373},
  year      = {2014},
  abstract  = {Because of its minor environmental impact, electricity generation using wind power is getting remarkable. The further growth of the wind industry depends on technological solutions to the challenges in production and construction of the turbines. Wind turbine tower vibrations, which limit power generation efficiency and cause fatigue problems with high maintenance costs, count as one of the main structural difficulties in the wind energy sector. To mitigate tower vibrations auxiliary measures are necessary. The effectiveness of tuned mass damper is verified by means of a numeric study on a 5 MW onshore reference wind turbine. Hereby, also seismic-induced vibrations and soil-structure interaction are considered. Acquired results show that tuned mass damper can effectively reduce resonant tower vibrations and improve the fatigue life of wind turbines. This chapter is also concerned with tuned liquid column damper and a semiactive application of it. Due to its geometric versatility and low prime costs, tuned liquid column dampers are a good alternative to other damping measures, in particular for slender structures like wind turbines.},
  language  = {en}
}
@book{KlinkelButenwegLinetal.2014,
  author    = {Klinkel, Sven and Butenweg, Christoph and Lin, Gao and Holtschoppen, Britta},
  title     = {Seismic design of industrial facilities : Proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF) / Sven Klinkel, Christoph Butenweg, Gao Lin, Britta Holtschoppen Editors},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  organization    = {International Conference on Seismic Design of Industrial Facilities <Aachen, 2013>},
  isbn      = {978-3-658-02809-1 (Print) ; 978-365-80281-0-7 (E-Book)},
  doi       = {10.1007/978-3-658-02810-7},
  pages     = {XIII, 450 S.},
  year      = {2014},
  language  = {en}
}
@techreport{ButenwegKaiser2014,
  author    = {Butenweg, Christoph and Kaiser, Diethelm},
  title     = {Seismic hazard harmonisation in Europe (SHARE) : DGEB-Workshop in Frankfurt a.M., Germany, 27. May 2014 / Christoph Butenweg, Diethelm Kaiser (editors)},
  publisher = {DGEB},
  address   = {Aachen},
  organization    = {Deutsche Gesellschaft f{\"u}r Erdbeben-Ingenieurwesen und Baudynamik},
  isbn      = {3-930108-12-7},
  pages     = {V, 117 S.},
  year      = {2014},
  language  = {en}
}
@inproceedings{FuchsRitz2014,
  author    = {Fuchs, Britta and Ritz, Thomas},
  title     = {Usability for Blended Shopping - Solving Major Flaws by Applying Usability Engineering and Proven Integration Technologies},
  series = {Proceedings of the 11th International Conference on e-Business, ICE-B 2014, Vienna, Austria},
  booktitle = {Proceedings of the 11th International Conference on e-Business, ICE-B 2014, Vienna, Austria},
  isbn      = {978-989-758-043-7},
  doi       = {10.5220/0005113502160223},
  pages     = {216 -- 223},
  year      = {2014},
  language  = {en}
}
@inproceedings{EdipGarevskiButenwegetal.2014,
  author    = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sheshov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor},
  title     = {New coupled finite-infinite element approach for wave propagation simulation of unbounded soil media},
  series = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2},
  booktitle = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2},
  publisher = {Curran Associates, Inc.},
  address   = {Red Hook, NY},
  organization    = {European Conference on Earthquake Engineering and Seismology <2, 2014, Istanbul>},
  isbn      = {978-1-5108-1021-1},
  pages     = {1556 -- 1561},
  year      = {2014},
  language  = {en}
}
@inproceedings{AltayButenwegKlinkeletal.2014,
  author    = {Altay, Okyay and Butenweg, Christoph and Klinkel, Sven and Taddei, Francesca},
  title     = {Vibration mitigation of wind turbine towers by tuned liquid column dampers},
  series = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)},
  booktitle = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)},
  address   = {Porto},
  organization    = {European Conference on Structural Dynamics, EURODYN <9, 2014, Porto>},
  isbn      = {978-972-752-165-4},
  pages     = {1531 -- 1538},
  year      = {2014},
  language  = {en}
}
@inproceedings{DalguerChurilovButenwegetal.2014,
  author    = {Dalguer, Luis A. and Churilov, Sergey and Butenweg, Christoph and Renault, Philippe and Hyun, An Jun},
  title     = {Dynamic analysis of a reinforced concrete electrical nuclear building of SMART 2013 project subjected to earthquake excitation using ABAQUS},
  series = {Workshop SMART2013 : Paris, France, November 25th - 27th, 2014},
  booktitle = {Workshop SMART2013 : Paris, France, November 25th - 27th, 2014},
  organization    = {Workshop SMART2013 <2014, Paris>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{HecklWeilerFleischhakeretal.2014,
  author    = {Heckl, O. H. and Weiler, Sascha and Fleischhaker, Robert and Gebs, Raphael and Budnicki, Aleksander and Wolf, M. and Kleinbauer, Jochen and Russ, S. and Kumkar, M. and Sutter, Dirk H.},
  title     = {Industry-grade high average power femtosecond light source},
  series = {Frontiers in ultrafast optics: Biomedical, scientific, and industrial applications XIV : 1 Februar 2014, San Francisco, USA. - (SPIE proceedings series ; 8972)},
  booktitle = {Frontiers in ultrafast optics: Biomedical, scientific, and industrial applications XIV : 1 Februar 2014, San Francisco, USA. - (SPIE proceedings series ; 8972)},
  editor    = {Heisterkamp, Alexander and Herman, Peter R. and Meunier, Michael and Nolte, Stefan},
  publisher = {SPIE, International Society for Optical Engineering},
  doi       = {10.1117/12.2039337},
  pages     = {89720P -- 89720P-7},
  year      = {2014},
  language  = {en}
}
@inproceedings{RosinKubalskiButenweg2014,
  author    = {Rosin, Julia and Kubalski, Thomas and Butenweg, Christoph},
  title     = {Seismic Design of cylindrical liquid storage tanks},
  series = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed.},
  booktitle = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed.},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  organization    = {International Conference on Seismic Design of Industrial Facilities <2013, Aachen>},
  isbn      = {978-3-658-02810-7 (E-Book) ; 978-3-658-02809-1 (Print)},
  doi       = {10.1007/978-3-658-02810-7_36},
  pages     = {429 -- 440},
  year      = {2014},
  language  = {en}
}
@inproceedings{EdipGarevskiButenwegetal.2014,
  author    = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sesov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor},
  title     = {Boundary effects on seismic analysis of multi-storey frames considering soil structure interaction phenomenon},
  series = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed},
  booktitle = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  organization    = {International Conference on Seismic Design of Industrial Facilities <2013, Aachen>},
  isbn      = {978-3-658-02809-1 (Print) ; 978-3-658-02810-7},
  doi       = {10.1007/978-3-658-02810-7_47},
  pages     = {569 -- 576},
  year      = {2014},
  language  = {en}
}
@inproceedings{GiresiniButenwegAndreinietal.2014,
  author    = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.},
  title     = {Numerical calibration of a macro-element for vaultes system in historic churches},
  series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  organization    = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{GiresiniButenwegAndreinietal.2014,
  author    = {Giresini, Linda and Butenweg, Christoph and Andreini, M. and De Falco, A. and Sassu, M.},
  title     = {Macro-elements identification in historic chapels: the case of St. Venerio Chapel in Reggiolo - Emilia Romagna},
  series = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  booktitle = {9th International Conference on Structural Analyses of Historical Conctruction, 14 - 17 October, 2014, Mexico City},
  organization    = {International Conference on Structural Analyses of Historical Conctructions <9, 2014, Mexico City>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{RosinButenweg2014,
  author    = {Rosin, Julia and Butenweg, Christoph},
  title     = {Seismic isolation of cylindrical liquid storage tanks},
  series = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)},
  booktitle = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)},
  address   = {Porto},
  organization    = {European Conference on Structural Dynamics, EURODYN <9, 2014, Porto>},
  isbn      = {978-972-752-165-4},
  pages     = {3145 -- 3152},
  year      = {2014},
  language  = {en}
}
@inproceedings{RosinHenneboehlButenweg2014,
  author    = {Rosin, Julia and Henneb{\"o}hl, Benedickt and Butenweg, Christoph},
  title     = {Global buckling analysis of cylindrical liquid storage tanks under earthquake loading},
  series = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 6},
  booktitle = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 6},
  publisher = {Curran Associates, Inc.},
  address   = {Red Hook, NY},
  organization    = {European Conference on Earthquake Engineering and Seismology <2, 2014, Istanbul>},
  isbn      = {978-1-5108-1021-1},
  pages     = {5270 -- 5281},
  year      = {2014},
  language  = {en}
}
@article{HaagZontarSchleupenetal.2014,
  author    = {Haag, S. and Zontar, D. and Schleupen, Josef and M{\"u}ller, T. and Brecher, C.},
  title     = {Chain of refined perception in self-optimizing assembly of micro-optical systems},
  series = {Journal of sensors and sensor systems},
  volume    = {3},
  journal   = {Journal of sensors and sensor systems},
  number    = {1},
  publisher = {Copernicus Publ.},
  address   = {G{\"o}ttingen},
  issn      = {2194-878X},
  doi       = {10.5194/jsss-3-87-2014},
  pages     = {87 -- 95},
  year      = {2014},
  abstract  = {Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements - especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base.},
  language  = {en}
}
@article{VosLagemaatBarentszetal.2014,
  author    = {Vos, E. K. and Lagemaat, M. W. and Barentsz, J. O. and F{\"u}tterer, J. J. and Zamecnik, P. and Roozen, H. and Orzada, S. and Bitz, Andreas and Maas, M. C. and Scheenen, T. W. J.},
  title     = {Image quality and cancer visibility of T2-weighted Magnetic Resonance Imaging of the prostate at 7 Tesla},
  series = {European Radiology},
  volume    = {24},
  journal   = {European Radiology},
  number    = {8},
  publisher = {Springer},
  address   = {Cham},
  issn      = {1432-1084},
  doi       = {10.1007/s00330-014-3234-6},
  pages     = {1950 -- 1958},
  year      = {2014},
  abstract  = {Objectives To assess the image quality of T2-weighted (T2w) magnetic resonance imaging of the prostate and the visibility of prostate cancer at 7 Tesla (T). Materials \& methods Seventeen prostate cancer patients underwent T2w imaging at 7T with only an external transmit/receive array coil. Three radiologists independently scored images for image quality, visibility of anatomical structures, and presence of artefacts. Krippendorff's alpha and weighted kappa statistics were used to assess inter-observer agreement. Visibility of prostate cancer lesions was assessed by directly linking the T2w images to the confirmed location of prostate cancer on histopathology. Results T2w imaging at 7T was achievable with 'satisfactory' (3/5) to 'good' (4/5) quality. Visibility of anatomical structures was predominantly scored as 'satisfactory' (3/5) and 'good' (4/5). If artefacts were present, they were mostly motion artefacts and, to a lesser extent, aliasing artefacts and noise. Krippendorff's analysis revealed an α = 0.44 between three readers for the overall image quality scores. Clinically significant cancer lesions in both peripheral zone and transition zone were visible at 7T. Conclusion T2w imaging with satisfactory to good quality can be routinely acquired, and cancer lesions were visible in patients with prostate cancer at 7T using only an external transmit/receive body array coil.},
  language  = {en}
}
@article{LagemaatVosMaasetal.2014,
  author    = {Lagemaat, Miriam W. and Vos, Eline K. and Maas, Marnix C. and Bitz, Andreas and Orzada, Stephan and Uden, Mark J. van and Kobus, Thiele and Heerschap, Arend and Scheenen, Tom W. J.},
  title     = {Phosphorus magnetic resonance spectroscopic imaging at 7 T in patients with prostate cancer},
  series = {Investigative Radiology},
  volume    = {49},
  journal   = {Investigative Radiology},
  number    = {5},
  publisher = {Lippincott Williams \& Wilkins},
  address   = {Philadelphia, Pa.},
  issn      = {1536-0210},
  doi       = {10.1097/RLI.0000000000000012},
  pages     = {363 -- 372},
  year      = {2014},
  abstract  = {Objectives The aim of this study was to identify characteristics of phosphorus (³¹P) spectra of the human prostate and to investigate changes of individual phospholipid metabolites in prostate cancer through in vivo ³¹P magnetic resonance spectroscopic imaging (MRSI) at 7 T. Materials and Methods In this institutional review board-approved study, 15 patients with biopsy-proven prostate cancer underwent T₂-weighted magnetic resonance imaging and 3-dimensional ³¹P MRSI at 7 T. Voxels were selected at the tumor location, in normal-appearing peripheral zone tissue, normal-appearing transition zone tissue, and in the base of the prostate close to the seminal vesicles. Phosphorus metabolite ratios were determined and compared between tissue types. Results Signals of phosphoethanolamine (PE) and phosphocholine (PC) were present and well resolved in most ³¹P spectra in the prostate. Glycerophosphocholine signals were observable in 43\% of the voxels in malignant tissue, but in only 10\% of the voxels in normal-appearing tissue away from the seminal vesicles. In many spectra, independent of tissue type, 2 peaks resonated in the chemical shift range of inorganic phosphate, possibly representing 2 separate pH compartments. The PC/PE ratio in the seminal vesicles was highly elevated compared with the prostate in 5 patients. A considerable overlap of ³¹P metabolite ratios was found between prostate cancer and normal-appearing prostate tissue, preventing direct discrimination of these tissues. The only 2 patients with high Gleason scores tumors (≥4+5) presented with high PC and glycerophosphocholine levels in their cancer lesions. Conclusions Phosphorus MRSI at 7 T shows distinct features of phospholipid metabolites in the prostate gland and its surrounding structures. In this exploratory study, no differences in ³¹P metabolite ratios were observed between prostate cancer and normal-appearing prostate tissue possibly because of the partial volume effects of small tumor foci in large MRSI voxels.},
  language  = {en}
}
@article{MaasVosLagemaatetal.2014,
  author    = {Maas, Marnix C. and Vos, Eline K. and Lagemaat, Miriam W. and Bitz, Andreas and Orzada, Stephan and Kobus, Thiele and Kraff, Oliver and Maderwald, Stefan and Ladd, Mark E. and Scheenen, Tom W. J.},
  title     = {Feasibility of T₂-weighted turbo spin echo imaging of the human prostate at 7 tesla},
  series = {Magnetic Resonance in Medicine},
  volume    = {71},
  journal   = {Magnetic Resonance in Medicine},
  number    = {5},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.24818},
  pages     = {1711 -- 1719},
  year      = {2014},
  abstract  = {Purpose To demonstrate that high quality T₂-weighted (T2w) turbo spin-echo (TSE) imaging of the complete prostate can be achieved routinely and within safety limits at 7 T, using an external transceive body array coil only. Methods Nine healthy volunteers and 12 prostate cancer patients were scanned on a 7 T whole-body system. Preparation consisted of B₀ and radiofrequency shimming and localized flip angle calibration. T₁ and T₂ relaxation times were measured and used to define the T2w-TSE protocol. T2w imaging was performed using a TSE sequence (pulse repetition time/echo time 3000-3640/71 ms) with prolonged excitation and refocusing pulses to reduce specific absorption rate. Results High quality T2w TSE imaging was performed in less than 2 min in all subjects. Tumors of patients with gold-standard tumor localization (MR-guided biopsy or prostatectomy) were well visualized on 7 T imaging (n = 3). The number of consecutive slices achievable within a 10-g averaged specific absorption rate limit of 10 W/kg was ≥28 in all subjects, sufficient for full prostate coverage with 3-mm slices in at least one direction. Conclusion High quality T2w TSE prostate imaging can be performed routinely and within specific absorption rate limits at 7 T with an external transceive body array.},
  language  = {en}
}
@article{PasteurTippkoetterKampeisetal.2014,
  author    = {Pasteur, Aline and Tippk{\"o}tter, Nils and Kampeis, Percy and Ulber, Roland},
  title     = {Optimization of high gradient magnetic separation filter units for the purification of fermentation products},
  series = {IEEE TRANSACTIONS ON MAGNETICS},
  volume    = {50},
  journal   = {IEEE TRANSACTIONS ON MAGNETICS},
  number    = {10},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {0018-9464},
  doi       = {10.1109/TMAG.2014.2325535},
  pages     = {Artikel 5000607},
  year      = {2014},
  abstract  = {High gradient magnetic separation (HGMS) has been established since the early 1970s. A more recent application of these systems is the use in bioprocesses. To integrate the HGMS in a fermentation process, it is necessary to optimize the separation matrix with regard to the magnetic separation characteristics and permeability of the non-magnetizable components of the fermentation broth. As part of the work presented here, a combined fluidic and magnetic force finite element model simulation was created using the software COMSOL Multiphysics and compared with separation experiments. Finally, as optimal lattice orientation of the separation matrix, a transversal rhombohedral arrangement was defined. The high suitability of the new filter matrix has been verified by separation experiments.},
  language  = {en}
}
@article{TippkoetterWollnySucketal.2014,
  author    = {Tippk{\"o}tter, Nils and Wollny, Steffen and Suck, Kirstin and Sohling, Ulrich and Ruf, Friedrich and Ulber, Roland},
  title     = {Recycling of spent oil bleaching earth as source of glycerol for the anaerobic production of acetone, butanol, and ethanol with Clostridium diolis and lipolytic Clostridium lundense},
  series = {Engineering in Life Sciences},
  volume    = {14},
  journal   = {Engineering in Life Sciences},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1618-2863},
  doi       = {10.1002/elsc.201300113},
  pages     = {425 -- 432},
  year      = {2014},
  abstract  = {A major part of edible oil is subjected to bleaching procedures, primarily with minerals applied as adsorbers. Their recycling is currently done either by regaining the oil via organic solvent extraction or by using the spent bleaching earth (SBE) as additive for animal feed, etc. As a new method, the reutilization of the by-product SBE for the microbiologic formation of acetone, butanol, and ethanol (ABE) is presented as proof-of-concept. The SBE was taken from a palm oil cleaning process. The recycling concept is based on the application of lipolytic clostridia strains. Due to considerably long fermentation times, co-fermentation with Candida rugosa and enzymatic hydrolyses of the bound oil with a subsequent clostridia fermentation are shown as alternative routes. Anaerobic fermentations under comparison of different clostridia strains were performed with glycerol media, enzymatically hydrolyzed palm oil and SBE. Solutes, side product compositions and productivities were quantified via HPLC. A successful production of ABE solutes from SBE has been done with a yield of 0.15 g butanol per gram of bound glycerol. Thus, the biotechnological recycling of the waste stream is possible in principle. Inhibition of the substrate suspension has been observed. A chromatographic ion-exchange of substrates increased the biomass concentration.},
  language  = {en}
}
@inproceedings{SchirraBauschatWatmuff2014,
  author    = {Schirra, Julian and Bauschat, J.-Michael and Watmuff, J.H.},
  title     = {Accurate induced drag prediction for highly non-planar lifting systems},
  series = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia},
  booktitle = {19th Australasian Fluid Mechanics Conference : 8.-11. Dezember 2014, Melbourne, Australia},
  pages     = {4 Seiten},
  year      = {2014},
  abstract  = {The impact of wake model effects is investigated for two highly non-planar lifting systems. Dependent on the geometrical arrangement of the configuration, the wake model shape is found to considerably affect the estimation. Particularly at higher angles of attack, an accurate estimation based on the common linear wake model approaches is involved.},
  language  = {en}
}
@article{TippkoetterDuweWiesenetal.2014,
  author    = {Tippk{\"o}tter, Nils and Duwe, Anna-Maria and Wiesen, Sebastian and Sieker, Tim and Ulber, Roland},
  title     = {Enzymatic hydrolysis of beech wood lignocellulose at high solid contents and its utilization as substrate for the production of biobutanol and dicarboxylic acids},
  series = {Bioresource Technology},
  volume    = {167},
  journal   = {Bioresource Technology},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.1016/j.biortech.2014.06.052},
  pages     = {447 -- 455},
  year      = {2014},
  abstract  = {The development of a cost-effective hydrolysis for crude cellulose is an essential part of biorefinery developments. To establish such high solid hydrolysis, a new solid state reactor with static mixing is used. However, concentrations >10\% (w/w) cause a rate and yield reduction of enzymatic hydrolysis. By optimizing the synergetic activity of cellulolytic enzymes at solid concentrations of 9\%, 17\% and 23\% (w/w) of crude Organosolv cellulose, glucose concentrations of 57, 113 and 152 g L⁻¹ are reached. However, the glucose yield decreases from 0.81 to 0.72gg⁻¹ at 17\% (w/w). Optimal conditions for hydrolysis scale-up under minimal enzyme addition are identified. As result, at 23\% (w/w) crude cellulose the glucose yield increases from 0.29 to 0.49gg⁻¹. As proof of its applicability, biobutanol, succinic and itaconic acid are produced with the crude hydrolysate. The potential of the substrate is proven e.g. by a high butanol yield of 0.33gg⁻¹.},
  language  = {en}
}
@article{HoehrPaulssenBenardetal.2014,
  author    = {Hoehr, Cornelia and Paulßen, Elisabeth and Benard, Francois and Lee, Chris Jaeil and Hou, Xinchi and Badesso, Brian and Ferguson, Simon and Miao, Qing and Yang, Hua and Buckley, Ken and Hanemaayer, Victoire and Zeisler, Stefan and Ruth, Thomas and Celler, Anna and Schaffer, Paul},
  title     = {⁴⁴ᶢSc production using a water target on a 13 MeV cyclotron},
  series = {Nuclear medicine and biology},
  volume    = {41},
  journal   = {Nuclear medicine and biology},
  number    = {5},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-9614},
  doi       = {10.1016/j.nucmedbio.2013.12.016},
  pages     = {401 -- 406},
  year      = {2014},
  abstract  = {Access to promising radiometals as isotopes for novel molecular imaging agents requires that they are routinely available and inexpensive to obtain. Proximity to a cyclotron center outfitted with solid target hardware, or to an isotope generator for the metal of interest is necessary, both of which can introduce significant hurdles in development of less common isotopes. Herein, we describe the production of ⁴⁴Sc (t₁⸝₂ = 3.97 h, Eavg,β⁺ = 1.47 MeV, branching ratio = 94.27\%) in a solution target and an automated loading system which allows a quick turn-around between different radiometallic isotopes and therefore greatly improves their availability for tracer development. Experimental yields are compared to theoretical calculations.},
  language  = {en}
}