@article{BungErpicumTullis2020,
  author    = {Bung, Daniel Bernhard and Erpicum, S{\´e}bastien and Tullis, Blanke P.},
  title     = {Advances in hydraulic structures engineering},
  series = {Journal of Hydraulic Engineering},
  volume    = {147},
  journal   = {Journal of Hydraulic Engineering},
  number    = {1},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {0733-9429 (Druckausgabe)},
  doi       = {10.1061/(ASCE)HY.1943-7900.0001851},
  pages     = {1 Seite},
  year      = {2020},
  language  = {en}
}
@article{BungCrookstonValero2020,
  author    = {Bung, Daniel Bernhard and Crookston, Brian M. and Valero, Daniel},
  title     = {Turbulent free-surface monitoring with an RGB-D sensor: the hydraulic jump case},
  series = {Journal of Hydraulic Research},
  journal   = {Journal of Hydraulic Research},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1814-2079},
  doi       = {10.1080/00221686.2020.1844810},
  year      = {2020},
  language  = {en}
}
@phdthesis{Bung2023,
  author    = {Bung, Daniel Bernhard},
  title     = {Imaging techniques for investigation of free-surface flows in hydraulic laboratories},
  doi       = {10.25926/BUW/0-172},
  pages     = {XXIII, 218 Seiten},
  year      = {2023},
  abstract  = {This thesis aims at the presentation and discussion of well-accepted and new imaging techniques applied to different types of flow in common hydraulic engineering environments. All studies are conducted in laboratory conditions and focus on flow depth and velocity measurements. Investigated flows cover a wide range of complexity, e.g. propagation of waves, dam-break flows, slightly and fully aerated spillway flows as well as highly turbulent hydraulic jumps. Newimagingmethods are compared to different types of sensorswhich are frequently employed in contemporary laboratory studies. This classical instrumentation as well as the general concept of hydraulic modeling is introduced to give an overview on experimental methods. Flow depths are commonly measured by means of ultrasonic sensors, also known as acoustic displacement sensors. These sensors may provide accurate data with high sample rates in case of simple flow conditions, e.g. low-turbulent clear water flows. However, with increasing turbulence, higher uncertainty must be considered. Moreover, ultrasonic sensors can provide point data only, while the relatively large acoustic beam footprint may lead to another source of uncertainty in case of relatively short, highly turbulent surface fluctuations (ripples) or free-surface air-water flows. Analysis of turbulent length and time scales of surface fluctuations from point measurements is also difficult. Imaging techniques with different dimensionality, however, may close this gap. It is shown in this thesis that edge detection methods (known from computer vision) may be used for two-dimensional free-surface extraction (i.e. from images taken through transparant sidewalls in laboratory flumes). Another opportunity in hydraulic laboratory studies comes with the application of stereo vision. Low-cost RGB-D sensors can be used to gather instantaneous, three-dimensional free-surface elevations, even in flows with very high complexity (e.g. aerated hydraulic jumps). It will be shown that the uncertainty of these methods is of similar order as for classical instruments. Particle Image Velocimetry (PIV) is a well-accepted and widespread imaging technique for velocity determination in laboratory conditions. In combination with high-speed cameras, PIV can give time-resolved velocity fields in 2D/3D or even as volumetric flow fields. PIV is based on a cross-correlation technique applied to small subimages of seeded flows. The minimum size of these subimages defines the maximum spatial resolution of resulting velocity fields. A derivative of PIV for aerated flows is also available, i.e. the so-called Bubble Image Velocimetry (BIV). This thesis emphasizes the capacities and limitations of both methods, using relatively simple setups with halogen and LED illuminations. It will be demonstrated that PIV/BIV images may also be processed by means of Optical Flow (OF) techniques. OF is another method originating from the computer vision discipline, based on the assumption of image brightness conservation within a sequence of images. The Horn-Schunck approach, which has been first employed to hydraulic engineering problems in the studies presented herein, yields dense velocity fields, i.e. pixelwise velocity data. As discussed hereinafter, the accuracy of OF competes well with PIV for clear-water flows and even improves results (compared to BIV) for aerated flow conditions. In order to independently benchmark the OF approach, synthetic images with defined turbulence intensitiy are used. Computer vision offers new opportunities that may help to improve the understanding of fluid mechanics and fluid-structure interactions in laboratory investigations. In prototype environments, it can be employed for obstacle detection (e.g. identification of potential fish migration corridors) and recognition (e.g. fish species for monitoring in a fishway) or surface reconstruction (e.g. inspection of hydraulic structures). It can thus be expected that applications to hydraulic engineering problems will develop rapidly in near future. Current methods have not been developed for fluids in motion. Systematic future developments are needed to improve the results in such difficult conditions.},
  language  = {en}
}
@inproceedings{Bung2012,
  author    = {Bung, Daniel Bernhard},
  title     = {Sensitivity of phase detection techniques in aerated chute flows to hydraulic design parameters},
  series = {2nd European IAHR congress : 27. - 29. June 2012, M{\"u}nchen},
  booktitle = {2nd European IAHR congress : 27. - 29. June 2012, M{\"u}nchen},
  publisher = {Lehrstuhl u. Versuchsanst. f{\"u}r Wasserbau u. Wasserwirtschaft d. TU M{\"u}nchen},
  address   = {M{\"u}nchen},
  organization    = {International Association for Hydraulic Engineering and Research},
  isbn      = {978-3-943683-03-5},
  pages     = {Artikelkennnummer: B15},
  year      = {2012},
  language  = {en}
}
@article{Bung2013,
  author    = {Bung, Daniel Bernhard},
  title     = {Non-intrusive detection of air-water surface roughness in self-aerated chute flows},
  series = {Journal of hydraulic research},
  volume    = {Vol. 51},
  journal   = {Journal of hydraulic research},
  number    = {Iss. 3},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1814-2079 (E-Journal); 0022-1686 (Print)},
  pages     = {322 -- 329},
  year      = {2013},
  language  = {en}
}
@article{Bung2021,
  author    = {Bung, Daniel Bernhard},
  title     = {Extreme flooding in Western Germany: some thoughts on hazards, return periods and risk},
  series = {Hydrolink},
  journal   = {Hydrolink},
  number    = {4},
  publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)},
  address   = {Madrid},
  pages     = {108 -- 113},
  year      = {2021},
  abstract  = {The low-pressure system Bernd involved extreme rainfalls in the Western part of Germany in July 2021, resulting in major floods, severe damages and a tremendous number of casualties. Such extreme events are rare and full flood protection can never be ensured with reasonable financial means. But still, this event must be starting point to reconsider current design concepts. This article aims at sharing some thoughts on potential hazards, the selection of return periods and remaining risk with the focus on Germany.},
  language  = {en}
}
@article{Bung2011,
  author    = {Bung, Daniel Bernhard},
  title     = {Developing flow in skimming flow regime on embankment stepped spillways},
  series = {Journal of hydraulic research},
  volume    = {Vol. 49},
  journal   = {Journal of hydraulic research},
  number    = {Iss. 5},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1814-2079 (E-Journal); 0022-1686 (Print)},
  pages     = {639 -- 648},
  year      = {2011},
  language  = {en}
}
@inproceedings{Bung2010,
  author    = {Bung, Daniel Bernhard},
  title     = {A comparative study of self-aerated stepped spillway and smooth invert chute flow: the effect of step-induced macro roughness},
  series = {5th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : CG JOINT 2010},
  booktitle = {5th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : CG JOINT 2010},
  publisher = {Univ. Press},
  address   = {Tianjin},
  organization    = {Chinese-German Joint Symposium on Hydraulic and Ocean Engineering <5, 2010, Tianjin>},
  isbn      = {978-7-5618-3671-2},
  pages     = {451 -- 456},
  year      = {2010},
  language  = {en}
}
@incollection{Bung2015,
  author    = {Bung, Daniel Bernhard},
  title     = {Laboratory models of free-surface flows},
  series = {Rivers - physical, fluvial and environmental processes},
  booktitle = {Rivers - physical, fluvial and environmental processes},
  editor    = {Rowinski, Pawel},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-17718-2 ; 978-3-319-17719-9},
  doi       = {10.1007/978-3-319-17719-9_9},
  pages     = {213 -- 228},
  year      = {2015},
  abstract  = {Hydraulic modeling is the classical approach to investigate and describe complex fluid motion. Many empirical formulas in the literature used for the hydraulic design of river training measures and structures have been developed using experimental data from the laboratory. Although computer capacities have increased to a high level which allows to run complex numerical simulations on standard workstation nowadays, non-standard design of structures may still raise the need to perform physical model investigations. These investigations deliver insight into details of flow patterns and the effect of varying boundary conditions. Data from hydraulic model tests may be used for calibration of numerical models as well. As the field of hydraulic modeling is very complex, this chapter intends to give a short overview on capacities and limits of hydraulic modeling in regard to river flows and hydraulic structures only. The reader shall get a first idea of modeling principles and basic considerations. More detailed information can be found in the references.},
  language  = {en}
}
@inproceedings{Bung2011,
  author    = {Bung, Daniel Bernhard},
  title     = {Non-intrusive measuring of air-water flow properties in self-aerated stepped spillway flow},
  series = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia},
  booktitle = {Balance and uncertainty - water in a changing world : proceedings of the 34th IAHR world congress ; 33rd Hydrology and Water Resources Symposium ; 10th Conference on Hydraulics in Water Engineering ; 26 June - 1 July 2011, Brisbane, Australia},
  organization    = {International Association for Hydraulic Engineering and Research},
  isbn      = {978-0-85825-868-6},
  pages     = {2380 -- 2387},
  year      = {2011},
  language  = {en}
}
@inproceedings{Bung2013,
  author    = {Bung, Daniel Bernhard},
  title     = {Air-water surface roughness in self-aerated stepped spillway flows},
  series = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China},
  booktitle = {35th IAHR world congress : 8.-13.9.2013, Chengdu, China},
  publisher = {Tsinghua Univ. Press},
  address   = {Beijing},
  organization    = {International Association for Hydraulic Engineering and Research},
  pages     = {Artikelkennnummer: A11045},
  year      = {2013},
  language  = {en}
}
@inproceedings{Bung2014,
  author    = {Bung, Daniel Bernhard},
  title     = {Observations on non-aerated flow and air entrainment on moderately sloped stepped spillways},
  series = {7th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : 8. - 12. Sept. 2014, Hannover},
  booktitle = {7th Chinese-German Joint Symposium on Hydraulic and Ocean Engineering : 8. - 12. Sept. 2014, Hannover},
  organization    = {Chinese-German Joint Symposium on Hydraulic and Ocean Engineering <7, 2014, Hannover>},
  pages     = {1 -- 8},
  year      = {2014},
  language  = {en}
}
@article{BullerschenWilhelmiWimmer1985,
  author    = {Bullerschen, Klaus-Gerd and Wilhelmi, Herbert and Wimmer, W.},
  title     = {Influence of non-uniform material properties and water cooling on current density and temperature profiles in arc furnace elektrodes},
  series = {Steel Research. 56 (1985), H. 11},
  journal   = {Steel Research. 56 (1985), H. 11},
  isbn      = {0177-4832},
  pages     = {559 -- 564},
  year      = {1985},
  language  = {en}
}
@article{BullerschenWilhelmi1991,
  author    = {Bullerschen, Klaus-Gerd and Wilhelmi, Herbert},
  title     = {Cooling of arc furnace electrodes with heat pipes},
  series = {Chemical Engineering \& Technology. 14 (1991), H. 1},
  journal   = {Chemical Engineering \& Technology. 14 (1991), H. 1},
  isbn      = {0930-7516},
  pages     = {45 -- 53},
  year      = {1991},
  language  = {en}
}
@inproceedings{BukhariYang2006,
  author    = {Bukhari, Syed Faisal Ahmed and Yang, Wuqiang},
  title     = {Multi-interface level sensors and new development in monitoring and control of oil separators},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1498},
  year      = {2006},
  abstract  = {In the oil industry, huge saving may be made if suitable multi-interface level measurement systems are employed for effectively monitoring crude oil separators and efficient control of their operation. A number of techniques, e.g. externally mounted displacers, differential pressure transmitters and capacitance rod devices, have been developed to measure the separation process with gas, oil, water and other components. Because of the unavailability of suitable multi-interface level measurement systems, oil separators are currently operated by the trial-and-error approach. In this paper some conventional techniques, which have been used for level measurement in industry, and new development are discussed.},
  subject      = {Biosensor},
  language  = {en}
}
@incollection{BudaSchuermannWollert2010,
  author    = {Buda, Aurel and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg},
  title     = {Wireless technologies in factory automation},
  series = {Factory automation / ed. by Javier Silvestre-Blanes},
  booktitle = {Factory automation / ed. by Javier Silvestre-Blanes},
  publisher = {Intech},
  address   = {London},
  isbn      = {978-953-7619-42-8},
  pages     = {29 -- 50},
  year      = {2010},
  language  = {en}
}
@inproceedings{BudaJozenfiniWollert2007,
  author    = {Buda, Aurel and Jozenfini, B. and Wollert, J{\"o}rg},
  title     = {Mobile ad-hoc Network for home automation based on ZigBee application framework},
  series = {1st European ZigBee Developer's Conference : June 18 - 20, 2007, Munich, Germany},
  booktitle = {1st European ZigBee Developer's Conference : June 18 - 20, 2007, Munich, Germany},
  publisher = {Design \& Elektronik},
  address   = {Poing},
  organization    = {European ZigBee Developer's Conference <1, 2007, M{\"u}nchen>},
  pages     = {1 -- 5},
  year      = {2007},
  language  = {en}
}
@article{BucurLazarescuPopetal.2019,
  author    = {Bucur, Alexandru and Lazarescu, Lucian and Pop, Grigore Marian and Achimas, Gheorghe and Gebhardt, Andreas},
  title     = {Tribological performance of biodegradable lubricants under different surface roughness of tools},
  series = {Academic Journal of Manufacturing Engineering},
  volume    = {17},
  journal   = {Academic Journal of Manufacturing Engineering},
  number    = {1},
  issn      = {1583-7904},
  pages     = {172 -- 178},
  year      = {2019},
  language  = {en}
}
@inproceedings{BuckWurmhoeringerLehleetal.2010,
  author    = {Buck, R. and Wurmh{\"o}ringer, K. and Lehle, R. and Pfahl, A. and G{\"o}ttsche, Joachim and Meyr, T.},
  title     = {Development of a 30m2 heliostat with hydraulic drive},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {74 -- 75},
  year      = {2010},
  language  = {en}
}
@inproceedings{BruessermannDeuster2005,
  author    = {Br{\"u}ssermann, Klaus and Deuster, M.},
  title     = {Temperature measurement to optimise the burning process},
  year      = {2005},
  abstract  = {One of the most important parameters in a burning chamber - in power stations, in waste to energy plants - is the temperature. This temperature is in the range of 700-1500 °C - one of the most advanced measuring methods being the acoustic pyrometry with the possibility of producing temperature mapping in one level of the burning chamber - comparable to computer tomography. The results of these measurements discussed in the presentation can be used - to fulfil the legal requirements in the FRG or in the EU - to equalise the temperature in one level of the burning chamber to optimise the steam production (better efficiency of the plant) and to minimise the production of temperature controlled flue gas components (NO, CO a. o.) - to control the SNCR-process if used.},
  subject      = {Pyrometrie},
  language  = {en}
}
@article{BruessermannAshtonLeichtetal.1994,
  author    = {Br{\"u}ssermann, Klaus and Ashton, P. and Leicht, R. and Martens, B.-R.},
  title     = {Concept of the Konrad repository documentation system for radioactive wastes (DORA) / Ashton, P.; Leicht, R.; Martens, B.-R.; Giller, H. Br{\"u}ssermann, K.},
  series = {Kerntechnik 94 : Jahrestagung, 17.-19. Mai 1994, Stuttgart: Tagungsbericht = Nuclear technology, annual meeting 94 / Veranst.: Kerntechnische Gesellschaft; Deutsches Atomforum},
  journal   = {Kerntechnik 94 : Jahrestagung, 17.-19. Mai 1994, Stuttgart: Tagungsbericht = Nuclear technology, annual meeting 94 / Veranst.: Kerntechnische Gesellschaft; Deutsches Atomforum},
  publisher = {INFORUM Verl.- u. Verwaltungs-Ges.},
  address   = {Bonn},
  pages     = {294 -- 297},
  year      = {1994},
  language  = {en}
}
@inproceedings{Bruessermann2005,
  author    = {Br{\"u}ssermann, Klaus},
  title     = {Platform of Excellence in "Energy and Environment"},
  year      = {2005},
  abstract  = {The Ministry of Science and Research in North Rhine-Westphalia created eight platforms of excellence, one in the research area „Energy and Environment" in 2002 at ACUAS. This platform concentrates the research and development of 13 professors in J{\"u}lich and Aachen and of two scientific institutes with different topics: - NOWUM-Energy with emphasis on efficient and economic energy conversion - The Solar Institute J{\"u}lich - SIJ - being the largest research institute in the field of renewables at a University of Applied Sciences in Germany With this platform each possible energy conversion - nuclear, fossil, renewable- can be dealt with to help solving the two most important problems of mankind, energy and potable water. At the CSE are presented the historical development, some research results and the combined master studies in „Energy Systems" and „Nuclear Applications"},
  subject      = {Energietechnik},
  language  = {en}
}
@book{Bruessermann1982,
  author    = {Br{\"u}ssermann, Klaus},
  title     = {Proceedings of the Workshop on Evaluation and Mitigation of Accidental Releases of Radioactivity, Identification of Uncertainties : Bad M{\"u}nstereifel, Fed. Republic of Germany, April 5th - 10th, 1981},
  publisher = {Ges. f{\"u}r Umwelt{\"u}berwachung},
  address   = {Aldenhoven},
  isbn      = {3-88668-014-2},
  pages     = {72 S.},
  year      = {1982},
  language  = {en}
}
@article{Bruessermann1989,
  author    = {Br{\"u}ssermann, Klaus},
  title     = {H3 and C14 air monitoring according to KTA 1503.1},
  series = {2. Karlsruhe international conference on analytical chemistry in nuclear technology, Karlsruhe (Germany), 5-9 Jun 1989},
  journal   = {2. Karlsruhe international conference on analytical chemistry in nuclear technology, Karlsruhe (Germany), 5-9 Jun 1989},
  pages     = {223},
  year      = {1989},
  language  = {en}
}
@article{BrueckSorgerGligorevicetal.2000,
  author    = {Br{\"u}ck, Stefan and Sorger, Ulrich and Gligorevic, Snjezana and Stolte, Norbert},
  title     = {Interleaving for outer convolutional codes in DS-CDMA systems},
  series = {IEEE transactions on communications},
  volume    = {Vol. 48},
  journal   = {IEEE transactions on communications},
  number    = {Iss. 7},
  issn      = {0090-6778},
  pages     = {1100 -- 1107},
  year      = {2000},
  language  = {en}
}
@article{BruksleChwallekKrastina2023,
  author    = {Bruksle, Ieva and Chwallek, Constanze and Krastina, Anzelika},
  title     = {Strengthening sustainability in entrepreneurship education - implications for shifting entrepreneurial thinking towards sustainability at universities},
  series = {ACTA PROSPERITATIS},
  volume    = {14},
  journal   = {ACTA PROSPERITATIS},
  number    = {1},
  publisher = {Sciendo},
  issn      = {1691-6077},
  doi       = {10.37804/1691-6077-2023-14-37-48},
  pages     = {37 -- 48},
  year      = {2023},
  abstract  = {By developing innovative solutions to social and environmental problems, sustainable ventures carry greatpotential. Entrepreneurship which focuses especially on new venture creation can be developed through education anduniversities, in particular, are called upon to provide an impetus for social change. But social innovations are associatedwith certain hurdles, which are related to the multi-dimensionality, i.e. the tension between creating social,environmental and economic value and dealing with a multiplicity of stakeholders. The already complex field ofentrepreneurship education has to face these challenges. This paper, therefore, aims to identify starting points for theintegration of sustainability into entrepreneurship education. To pursue this goal experiences from three differentproject initiatives between the partner universities: Lapland University of Applied Sciences, FH Aachen University ofApplied Sciences and Turiba University are reflected and findings are systematically condensed into recommendationsfor education on sustainable entrepreneurship.},
  language  = {en}
}
@article{BronderWuPoghossianetal.2014,
  author    = {Bronder, Thomas and Wu, Chunsheng and Poghossian, Arshak and Werner, Frederik and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Label-free detection of DNA hybridization with light-addressable potentiometric sensors: comparison of various DNA-immobilization strategies},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.647},
  pages     = {755 -- 758},
  year      = {2014},
  abstract  = {Light-addressable potentiometric sensors (LAPS) consisting of a p-Si-SiO2 and p-Si-SiO2-Au structure, respectively, have been tested for a label-free electrical detection of DNA (deoxyribonucleic acid) hybridization. Three different strategies for immobilizing single-stranded probe DNA (ssDNA) molecules on a LAPS surface have been studied and compared: (a) immobilization of thiol-modified ssDNA on the patterned Au surface via gold-thiol bond, (b) covalent immobilization of amino-modified ssDNA onto the SiO2 surface functionalized with 3-aminopropyltriethoxysilane and (c) layer-by-layer adsorption of negatively charged ssDNA on a positively charged weak polyelectrolyte layer of poly(allylamine hydrochloride).},
  language  = {en}
}
@article{BronderPoghossianSchejaetal.2015,
  author    = {Bronder, Thomas and Poghossian, Arshak and Scheja, Sabrina and Wu, Chunsheng and Keusgen, Michael and Mewes, Dieter and Sch{\"o}ning, Michael Josef},
  title     = {DNA Immobilization and Hybridization Detection by the Intrinsic Molecular Charge Using Capacitive Field-Effect Sensors Modified with a Charged Weak Polyelectrolyte Layer},
  series = {Applied Materials \& Interfaces},
  volume    = {36},
  journal   = {Applied Materials \& Interfaces},
  number    = {7},
  publisher = {American Chemical Society},
  address   = {Washington, DC},
  doi       = {10.1021/acsami.5b05146},
  pages     = {20068 -- 20075},
  year      = {2015},
  abstract  = {Miniaturized setup, compatibility with advanced micro- and nanotechnologies, and ability to detect biomolecules by their intrinsic molecular charge favor the semiconductor field-effect platform as one of the most attractive approaches for the development of label-free DNA chips. In this work, a capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensor covered with a layer-by-layer prepared, positively charged weak polyelectrolyte layer of PAH (poly(allylamine hydrochloride)) was used for the label-free electrical detection of DNA (deoxyribonucleic acid) immobilization and hybridization. The negatively charged probe single-stranded DNA (ssDNA) molecules were electrostatically adsorbed onto the positively charged PAH layer, resulting in a preferentially flat orientation of the ssDNA molecules within the Debye length, thus yielding a reduced charge-screening effect and a higher sensor signal. Each sensor-surface modification step (PAH adsorption, probe ssDNA immobilization, hybridization with complementary target DNA (cDNA), reducing an unspecific adsorption by a blocking agent, incubation with noncomplementary DNA (ncDNA) solution) was monitored by means of capacitance-voltage and constant-capacitance measurements. In addition, the surface morphology of the PAH layer was studied by atomic force microscopy and contact-angle measurements. High hybridization signals of 34 and 43 mV were recorded in low-ionic strength solutions of 10 and 1 mM, respectively. In contrast, a small signal of 4 mV was recorded in the case of unspecific adsorption of fully mismatched ncDNA. The density of probe ssDNA and dsDNA molecules as well as the hybridization efficiency was estimated using the experimentally measured DNA immobilization and hybridization signals and a simplified double-layer capacitor model. The results of field-effect experiments were supported by fluorescence measurements, verifying the DNA-immobilization and hybridization event.},
  language  = {en}
}
@article{BronderPoghossianSchejaetal.2015,
  author    = {Bronder, Thomas and Poghossian, Arshak and Scheja, S. and Wu, Chunsheng and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Electrostatic Detection of Unlabelled Single- and Double-stranded DNA Using Capacitive Field-effect Devices Functionalized with a Positively Charged Polyelectrolyte Layer},
  series = {Procedia Engineering},
  volume    = {120},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2015.08.710},
  pages     = {544 -- 547},
  year      = {2015},
  abstract  = {Capacitive field-effect electrolyte-insulator-semiconductor sensors consisting of an Al-p-Si-SiO2 structure have been used for the electrical detection of unlabelled single- and double-stranded DNA (dsDNA) molecules by their intrinsic charge. A simple functionalization protocol based on the layer-by-layer (LbL) technique was used to prepare a weak polyelectrolyte/probe-DNA bilayer, followed by the hybridization with complementary target DNA molecules. Due to the flat orientation of the LbL-adsorbed DNA molecules, a high sensor signal has been achieved. In addition, direct label-free detection of in-solution hybridized dsDNA molecules has been studied.},
  language  = {en}
}
@article{BronderPoghossianKeusgenetal.2017,
  author    = {Bronder, Thomas and Poghossian, Arshak and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Label-free detection of double-stranded DNA molecules with polyelectrolyte-modified capacitive field-effect sensors},
  series = {tm - Technisches Messen},
  volume    = {84},
  journal   = {tm - Technisches Messen},
  number    = {10},
  publisher = {De Gruyter},
  address   = {Oldenbourg},
  doi       = {10.1515/teme-2017-0015},
  pages     = {628 -- 634},
  year      = {2017},
  abstract  = {In this study, polyelectrolyte-modified field-effect-based electrolyte-insulator-semiconductor (EIS) devices have been used for the label-free electrical detection of double-stranded deoxyribonucleic acid (dsDNA)molecules. The sensor-chip functionalization with a positively charged polyelectrolyte layer provides the possibility of direct adsorptive binding of negatively charged target DNA oligonucleotides onto theSiO2-chip surface.EIS sensors can be utilized as a tool to detect surface-charge changes; the electrostatic adsorption of oligonucleotides onto the polyelectrolyte layer leads to a measureable surface-potential change. Signals of 39mV have been recorded after the incubation with the oligonucleotide solution. Besides the electrochemical experiments, the successful adsorption of dsDNA onto the polyelectrolyte layer has been verified via fluorescence microscopy. The presented results demonstrate that the signal recording of EISchips, which are modified with a polyelectrolyte layer, canbe used as a favorable approach for a fast, cheap and simple detection method for dsDNA.},
  language  = {en}
}
@article{BronderPoghossianJessingetal.2019,
  author    = {Bronder, Thomas and Poghossian, Arshak and Jessing, Max P. and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Surface regeneration and reusability of label-free DNA biosensors based on weak polyelectrolyte-modified capacitive field-effect structures},
  series = {Biosensors and Bioelectronics},
  volume    = {126},
  journal   = {Biosensors and Bioelectronics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0956-5663},
  doi       = {10.1016/j.bios.2018.11.019},
  pages     = {510 -- 517},
  year      = {2019},
  language  = {en}
}
@article{BronderJessingPoghossianetal.2018,
  author    = {Bronder, Thomas and Jessing, Max P. and Poghossian, Arshak and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Detection of PCR-Amplified Tuberculosis DNA Fragments with Polyelectrolyte-Modified Field-Effect Sensors},
  series = {Analytical Chemistry},
  volume    = {90},
  journal   = {Analytical Chemistry},
  number    = {12},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  issn      = {0003-2700},
  doi       = {10.1021/acs.analchem.8b01807},
  pages     = {7747 -- 7753},
  year      = {2018},
  abstract  = {Field-effect-based electrolyte-insulator-semiconductor (EIS) sensors were modified with a bilayer of positively charged weak polyelectrolyte (poly(allylamine hydrochloride) (PAH)) and probe single-stranded DNA (ssDNA) and are used for the detection of complementary single-stranded target DNA (cDNA) in different test solutions. The sensing mechanism is based on the detection of the intrinsic molecular charge of target cDNA molecules after the hybridization event between cDNA and immobilized probe ssDNA. The test solutions contain synthetic cDNA oligonucleotides (with a sequence of tuberculosis mycobacteria genome) or PCR-amplified DNA (which origins from a template DNA strand that has been extracted from Mycobacterium avium paratuberculosis-spiked human sputum samples), respectively. Sensor responses up to 41 mV have been measured for the test solutions with DNA, while only small signals of ∼5 mV were detected for solutions without DNA. The lower detection limit of the EIS sensors was ∼0.3 nM, and the sensitivity was ∼7.2 mV/decade. Fluorescence experiments using SybrGreen I fluorescence dye support the electrochemical results.},
  language  = {en}
}
@phdthesis{Bronder2020,
  author    = {Bronder, Thomas},
  title     = {Label-free detection of tuberculosis DNA with capacitive field-effect biosensors},
  publisher = {Philipps-Universit{\"a}t Marburg},
  address   = {Marburg},
  doi       = {10.17192/z2021.0056},
  pages     = {X, 162 S},
  year      = {2020},
  language  = {en}
}
@inproceedings{BroennerHoefkenSchuba2016,
  author    = {Broenner, Simon and H{\"o}fken, Hans-Wilhelm and Schuba, Marko},
  title     = {Streamlining extraction and analysis of android RAM images},
  series = {Proceedings of the 2nd international conference on information systems security and privacy},
  booktitle = {Proceedings of the 2nd international conference on information systems security and privacy},
  organization    = {ICISSP International Conference on Information Systems Security and Privacy <2, 2016, Rome, Italy>},
  isbn      = {978-989-758-167-0},
  doi       = {10.5220/0005652802550264},
  pages     = {255 -- 264},
  year      = {2016},
  language  = {en}
}
@inproceedings{BrockmannSultanowCzarnecki2019,
  author    = {Brockmann, Carsten and Sultanow, Eldar and Czarnecki, Christian},
  title     = {Is enterprise architecture still relevant in the digital age?},
  series = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge},
  booktitle = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge},
  editor    = {Draude, Claude and Lange, Martin and Sick, Bernhard},
  publisher = {K{\"o}llen},
  address   = {Bonn},
  isbn      = {9783885796893},
  issn      = {1617-5468},
  doi       = {10.18420/inf2019_ws01},
  pages     = {21 -- 21},
  year      = {2019},
  language  = {en}
}
@inproceedings{BrockmannSultanowCzarnecki2018,
  author    = {Brockmann, Carsten and Sultanow, Eldar and Czarnecki, Christian},
  title     = {Enterprise architectures between agility and traditional methodologies},
  series = {GI Edition Proceedings Band 285 Workshops der INFORMATIK 2018},
  booktitle = {GI Edition Proceedings Band 285 Workshops der INFORMATIK 2018},
  editor    = {Czarnecki, Christian and Brockmann, Carsten and Sultanow, Eldar and Koschmider, Agnes and Selzer, Annika and Gesellschaft f{\"u}r Informatik e. V.,},
  publisher = {K{\"o}llen},
  address   = {Bonn},
  isbn      = {9783885796794},
  issn      = {1617-5468},
  pages     = {1 Seite},
  year      = {2018},
  abstract  = {For this year's workshop on Enterpirse Architecture in Research and Practice we have received eight submissions from which four have passed the rigorous peer-review. The acceptance quote of 50\% assures that only advancements in the field are included in our workshop.},
  language  = {en}
}
@article{BrockhausBehbahaniMurisetal.2021,
  author    = {Brockhaus, Moritz K. and Behbahani, Mehdi and Muris, Farina and Jansen, Sebastian V. and Schmitz-Rode, Thomas and Steinseifer, Ulrich and Clauser, Johanna C.},
  title     = {In vitro thrombogenicity testing of pulsatile mechanical circulatory support systems: Design and proof-of-concept},
  series = {Artificial Organs},
  volume    = {45},
  journal   = {Artificial Organs},
  number    = {12},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1525-1594},
  doi       = {10.1111/aor.14046},
  pages     = {1513 -- 1521},
  year      = {2021},
  abstract  = {Thrombogenic complications are a main issue in mechanical circulatory support (MCS). There is no validated in vitro method available to quantitatively assess the thrombogenic performance of pulsatile MCS devices under realistic hemodynamic conditions. The aim of this study is to propose a method to evaluate the thrombogenic potential of new designs without the use of complex in-vivo trials. This study presents a novel in vitro method for reproducible thrombogenicity testing of pulsatile MCS systems using low molecular weight heparinized porcine blood. Blood parameters are continuously measured with full blood thromboelastometry (ROTEM; EXTEM, FIBTEM and a custom-made analysis HEPNATEM). Thrombus formation is optically observed after four hours of testing. The results of three experiments are presented each with two parallel loops. The area of thrombus formation inside the MCS device was reproducible. The implantation of a filter inside the loop catches embolizing thrombi without a measurable increase of platelet activation, allowing conclusions of the place of origin of thrombi inside the device. EXTEM and FIBTEM parameters such as clotting velocity (α) and maximum clot firmness (MCF) show a total decrease by around 6\% with a characteristic kink after 180 minutes. HEPNATEM α and MCF rise within the first 180 minutes indicate a continuously increasing activation level of coagulation. After 180 minutes, the consumption of clotting factors prevails, resulting in a decrease of α and MCF. With the designed mock loop and the presented protocol we are able to identify thrombogenic hot spots inside a pulsatile pump and characterize their thrombogenic potential.},
  language  = {en}
}
@incollection{BrittenBraunHesseetal.2003,
  author    = {Britten, G. and Braun, Carsten and Hesse, M. and Ballmann, Josef},
  title     = {Computational aeroelasticity with reduced structural models},
  series = {Flow modulation and fluid-structure interaction at airplane wings : research results of the Collaborative Research Center SFB 401 at RWTH Aachen, University of Technology, Aachen, Germany / Josef Ballmann (Ed.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 84},
  booktitle = {Flow modulation and fluid-structure interaction at airplane wings : research results of the Collaborative Research Center SFB 401 at RWTH Aachen, University of Technology, Aachen, Germany / Josef Ballmann (Ed.) Notes on numerical fluid mechanics and multidisciplinary design. Vol. 84},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {3-540-40209-8},
  pages     = {275 -- 299},
  year      = {2003},
  language  = {en}
}
@article{BreussKleefeld2020,
  author    = {Breuß, Michael and Kleefeld, Andreas},
  title     = {Implicit monotone difference methods for scalar conservation laws with source terms},
  series = {Acta Mathematica Vietnamica},
  volume    = {45},
  journal   = {Acta Mathematica Vietnamica},
  publisher = {Springer Singapore},
  address   = {Singapore},
  issn      = {2315-4144},
  doi       = {10.1007/s40306-019-00354-1},
  pages     = {709 -- 738},
  year      = {2020},
  abstract  = {In this article, a concept of implicit methods for scalar conservation laws in one or more spatial dimensions allowing also for source terms of various types is presented. This material is a significant extension of previous work of the first author (Breuß SIAM J. Numer. Anal. 43(3), 970-986 2005). Implicit notions are developed that are centered around a monotonicity criterion. We demonstrate a connection between a numerical scheme and a discrete entropy inequality, which is based on a classical approach by Crandall and Majda. Additionally, three implicit methods are investigated using the developed notions. Next, we conduct a convergence proof which is not based on a classical compactness argument. Finally, the theoretical results are confirmed by various numerical tests.},
  language  = {en}
}
@article{BreuerRaueStrobeletal.2016,
  author    = {Breuer, Lars and Raue, Markus and Strobel, M. and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, R. and Wagner, Torsten},
  title     = {Hydrogels with incorporated graphene oxide as light-addressable actuator materials for cell culture environments in lab-on-chip systems},
  series = {Physica status solidi (a)},
  volume    = {213},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.201533056},
  pages     = {1520 -- 1525},
  year      = {2016},
  abstract  = {Abstractauthoren Graphene oxide (GO) nanoparticles were incorporated in temperature-sensitive Poly(N-isopropylacrylamide) (PNIPAAm) hydrogels. The nanoparticles increase the light absorption and convert light energy into heat efficiently. Thus, the hydrogels with GO can be stimulated spatially resolved by illumination as it was demonstrated by IR thermography. The temporal progression of the temperature maximum was detected for different concentrations of GO within the polymer network. Furthermore, the compatibility of PNIPAAm hydrogels with GO and cell cultures was investigated. For this purpose, culture medium was incubated with hydrogels containing GO and the viability and morphology of chinese hamster ovary (CHO) cells was examined after several days of culturing in presence of this medium.},
  language  = {en}
}
@inproceedings{BreuerRaueMangetal.2015,
  author    = {Breuer, Lars and Raue, Markus and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Light-stimulated hydrogel actuators with incorporated graphene oxide for microfluidic applications},
  series = {12. Dresdner Sensor-Symposium 2015},
  booktitle = {12. Dresdner Sensor-Symposium 2015},
  doi       = {10.5162/12dss2015/P5.8},
  pages     = {206 -- 209},
  year      = {2015},
  language  = {en}
}
@article{BreuerRaueKirschbaumetal.2015,
  author    = {Breuer, Lars and Raue, Markus and Kirschbaum, M. and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, R. and Wagner, Torsten},
  title     = {Light-controllable polymeric material based on temperature-sensitive hydrogels with incorporated graphene oxide},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431944},
  pages     = {1368 -- 1374},
  year      = {2015},
  abstract  = {Poly(N-isopropylacrylamide) (PNIPAAm) hydrogel films with incorporated graphene oxide (GO) were developed and tested as light-stimulated actuators. GO dispersions were synthesized via Hummers method and characterized toward their optical properties and photothermal energy conversion. The hydrogels were prepared by means of photopolymerization. In addition, the influence of GO within the hydrogel network on the lower critical solution temperature (LCST) was investigated by differential scanning calorimetry (DSC). The optical absorbance and the response to illumination were determined as a function of GO concentration for thin hydrogel films. A proof of principle for the stimulation with light was performed.},
  language  = {en}
}
@article{BreuerPilasGuthmannetal.2019,
  author    = {Breuer, Lars and Pilas, Johanna and Guthmann, Eric and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Towards light-addressable flow control: responsive hydrogels with incorporated graphene oxide as laser-driven actuator structures within microfluidic channels},
  series = {Sensor and Actuators B: Chemical},
  volume    = {288},
  journal   = {Sensor and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2019.02.086},
  pages     = {579 -- 585},
  year      = {2019},
  language  = {en}
}
@article{BreuerMangSchoeningetal.2017,
  author    = {Breuer, Lars and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Investigation of the spatial resolution of a laser-based stimulation process for light-addressable hydrogels with incorporated graphene oxide by means of IR thermography},
  series = {Sensors and Actuators A: Physical},
  volume    = {268},
  journal   = {Sensors and Actuators A: Physical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0924-4247},
  doi       = {10.1016/j.sna.2017.11.031},
  pages     = {126 -- 132},
  year      = {2017},
  language  = {en}
}
@inproceedings{BreuerGuthmannSchoeningetal.2017,
  author    = {Breuer, Lars and Guthmann, Eric and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Light-Stimulated Hydrogels with Incorporated Graphene Oxide as Actuator Material for Flow Control in Microfluidic Applications},
  series = {Proceedings Eurosensors 2017 Conference, Paris, France, 3-6 September 2017},
  booktitle = {Proceedings Eurosensors 2017 Conference, Paris, France, 3-6 September 2017},
  doi       = {10.3390/proceedings1040524},
  pages     = {1 -- 4},
  year      = {2017},
  language  = {en}
}
@article{BresselSchultzeKhanetal.2003,
  author    = {Bressel, A. and Schultze, J.W. and Khan, W. and Wolfaardt, G. M. and Rohns, H.-P. and Irmscher, R. and Sch{\"o}ning, Michael Josef},
  title     = {High resolution gravimetric, optical and electrochemical investigations of microbial biofilm formation in aqueous systems},
  series = {Electrochimica Acta. 48 (2003), H. 20-22},
  journal   = {Electrochimica Acta. 48 (2003), H. 20-22},
  isbn      = {0013-4686},
  pages     = {3363 -- 3372},
  year      = {2003},
  language  = {en}
}
@article{BreitbachWolfDeschkaetal.1992,
  author    = {Breitbach, Gerd and Wolf, U. and Deschka, S. and Nickel, H.},
  title     = {Thermomechanical analysis of an actively cooled divertor mock up},
  series = {Tagungsbericht : Jahrestagung Kerntechnik : Stadthalle Karlsruhe, 5.-7. Mai 1992, Karlsruhe = Proceedings / Kerntechnische Gesellschaft ... [Red.: Karl G. Bauer]. - 1. Aufl., als Ms. gedr..},
  journal   = {Tagungsbericht : Jahrestagung Kerntechnik : Stadthalle Karlsruhe, 5.-7. Mai 1992, Karlsruhe = Proceedings / Kerntechnische Gesellschaft ... [Red.: Karl G. Bauer]. - 1. Aufl., als Ms. gedr..},
  publisher = {INFOFORUM},
  address   = {Bonn},
  pages     = {457 -- 461},
  year      = {1992},
  language  = {en}
}
@article{BreitbachSchubert2004,
  author    = {Breitbach, Gerd and Schubert, F.},
  title     = {A contribution to stress prediction in coatings for gas turbine blades},
  series = {Archive of applied mechanics. 73 (2004), H. 9-10},
  journal   = {Archive of applied mechanics. 73 (2004), H. 9-10},
  isbn      = {0939-1533},
  pages     = {682 -- 689},
  year      = {2004},
  language  = {en}
}
@article{BreitbachSchmidtPlutkaSchubertetal.1993,
  author    = {Breitbach, Gerd and Schmidt-Plutka, A. and Schubert, F. and Nickel, H.},
  title     = {Deformation behaviour of structures exposed at very high temperatures to cyclic thermal and mechanical loadings},
  series = {Structural mechanics in reactor technology : transactions of the 12th International Conference on Structural Mechanics in Reactor Technology, Stuttgart, Germany, 15-20 August 1993 / ed. Karl F. Kussmaul. - Bd. L : Inelastic behaviour of solids and structures},
  journal   = {Structural mechanics in reactor technology : transactions of the 12th International Conference on Structural Mechanics in Reactor Technology, Stuttgart, Germany, 15-20 August 1993 / ed. Karl F. Kussmaul. - Bd. L : Inelastic behaviour of solids and structures},
  publisher = {Elsevier},
  address   = {Amsterdam [u.a.]},
  isbn      = {0-444-81515-5},
  pages     = {203 -- 208},
  year      = {1993},
  language  = {en}
}
@article{BreitbachDeschkaAkiba1992,
  author    = {Breitbach, Gerd and Deschka, S. and Akiba, M.},
  title     = {High heat flux tests on brazed divertor components in electron and ion beam test facilities / S. Deschka ; M. Akiba ; G. Breitbach ...},
  series = {International journal of refractory metals and hard materials. 11 (1992), H. 6},
  journal   = {International journal of refractory metals and hard materials. 11 (1992), H. 6},
  isbn      = {0263-4368},
  pages     = {367 -- 375},
  year      = {1992},
  language  = {en}
}