@inproceedings{ŠakićMilijašMarinkovićetal.2021,
  author    = {Šakić, Bogdan and Milijaš, Aleksa and Marinković, Marko and Butenweg, Christoph and Klinkel, Sven},
  title     = {Influence of prior in-plane damage on the out-of-plane response of non-load bearing unreinforced masonry walls under seismic load},
  series = {8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering},
  booktitle = {8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering},
  editor    = {Papadrakakis, Manolis and Fragiadakis, Michalis},
  publisher = {National Technical University of Athens},
  address   = {Athen},
  isbn      = {9786188507258},
  issn      = {2623-3347},
  doi       = {10.7712/120121.8527.18913},
  pages     = {808 -- 828},
  year      = {2021},
  abstract  = {Reinforced concrete frames with masonry infill walls are popular form of construction all over the world as well in seismic regions. While severe earthquakes can cause high level of damage of both reinforced concrete and masonry infills, earthquakes of lower to medium intensity some-times can cause significant level of damage of masonry infill walls. Especially important is the level of damage of face loaded infill masonry walls (out-of-plane direction) as out-of-plane load cannot only bring high level of damage to the wall, it can also be life-threating for the people near the wall. The response in out-of-plane direction directly depends on the prior in-plane damage, as previous investigation shown that it decreases resistance capacity of the in-fills. Behaviour of infill masonry walls with and without prior in-plane load is investigated in the experimental campaign and the results are presented in this paper. These results are later compared with analytical approaches for the out-of-plane resistance from the literature. Conclusions based on the experimental campaign on the influence of prior in-plane damage on the out-of-plane response of infill walls are compared with the conclusions from other authors who investigated the same problematic.},
  language  = {en}
}
@inproceedings{ZieglerSchuellerMottaghy2013,
  author    = {Ziegler, M. and Sch{\"u}ller, R. and Mottaghy, Darius},
  title     = {Numerical simulation of energy consumption of artificial ground freezing applications subject to water seepage},
  series = {Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013},
  booktitle = {Proceedings of the 18th International Conference on Soil Mechanics and Geotechnical Engineering, Paris 2013},
  pages     = {2985 -- 2988},
  year      = {2013},
  language  = {en}
}
@inproceedings{ZahraPhaniSrujanCaminosetal.2022,
  author    = {Zahra, Mahdi and Phani Srujan, Merige and Caminos, Ricardo Alexander Chico and Schmitz, Pascal and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e} and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and Dersch, J{\"u}rgen},
  title     = {Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086268},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica.},
  language  = {en}
}
@inproceedings{WetterKern2014,
  author    = {Wetter, Martin and Kern, Alexander},
  title     = {Number of lightning strikes to tall structures - comparison of calculations and measurements using a modern lightning monitoring system},
  series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  organization    = {International Conference on Lightning Protection <2014, Shanghai>},
  pages     = {1 -- 7},
  year      = {2014},
  language  = {en}
}
@inproceedings{WagnerNohButenwegetal.2002,
  author    = {Wagner, R. and Noh, S.-Y. and Butenweg, Christoph and Meskouris, Konstantin},
  title     = {Seismic excited granular material silos},
  series = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ...},
  booktitle = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ...},
  publisher = {Balkema},
  address   = {Lisse},
  organization    = {European Conference on Structural Dynamics, EURODYN <5, 2002, M{\"u}nchen>},
  isbn      = {90-5809-511-8},
  pages     = {253 -- 258},
  year      = {2002},
  language  = {en}
}
@inproceedings{TomićPennaDeJongetal.2020,
  author    = {Tomić, Igor and Penna, Andrea and DeJong, Matthew and Butenweg, Christoph and Correia, Ant{\´o}nio A. and Candeias, Paulo X. and Senaldi, Ilaria and Guerrini, Gabriele and Malomo, Daniele and Beyer, Katrin},
  title     = {Seismic testing of adjacent interacting masonry structures},
  series = {12th International Conference on Structural Analysis of Historical Constructions (SAHC 2020)},
  booktitle = {12th International Conference on Structural Analysis of Historical Constructions (SAHC 2020)},
  doi       = {10.23967/sahc.2021.234},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {In many historical centres in Europe, stone masonry buildings are part of building aggregates, which developed when the layout of the city or village was densified. In these aggregates, adjacent buildings share structural walls to support floors and roofs. Meanwhile, the masonry walls of the fa{\c{c}}ades of adjacent buildings are often connected by dry joints since adjacent buildings were constructed at different times. Observations after for example the recent Central Italy earthquakes showed that the dry joints between the building units were often the first elements to be damaged. As a result, the joints opened up leading to pounding between the building units and a complicated interaction at floor and roof beam supports. The analysis of such building aggregates is very challenging and modelling guidelines do not exist. Advances in the development of analysis methods have been impeded by the lack of experimental data on the seismic response of such aggregates. The objective of the project AIMS (Seismic Testing of Adjacent Interacting Masonry Structures), included in the H2020 project SERA, is to provide such experimental data by testing an aggregate of two buildings under two horizontal components of dynamic excitation. The test unit is built at half-scale, with a two-storey building and a one-storey building. The buildings share one common wall while the fa{\c{c}}ade walls are connected by dry joints. The floors are at different heights leading to a complex dynamic response of this smallest possible building aggregate. The shake table test is conducted at the LNEC seismic testing facility. The testing sequence comprises four levels of shaking: 25\%, 50\%, 75\% and 100\% of nominal shaking table capacity. Extensive instrumentation, including accelerometers, displacement transducers and optical measurement systems, provides detailed information on the building aggregate response. Special attention is paid to the interface opening, the globa},
  language  = {en}
}
@inproceedings{TomicPennaDeJongetal.2020,
  author    = {Tomic, Igor and Penna, Andrea and DeJong, Matthew and Butenweg, Christoph and Senaldi, Ilaria and Guerrini, Gabriele and Malomo, Daniele and Beyer, Katrin},
  title     = {Blind predictions of shake table testing of aggregate masonry buildings},
  series = {17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.},
  booktitle = {17th World Conference on Earthquake Engineering, Sendai, Japan, September 27 to October 2, 2021.},
  year      = {2020},
  abstract  = {In many historical centers in Europe, stone masonry is part of building aggregates, which developed when the layout of the city or village was densified. The analysis of such building aggregates is very challenging and modelling guidelines missing. Advances in the development of analysis methods have been impeded by the lack of experimental data on the seismic response of such aggregates. The SERA project AIMS (Seismic Testing of Adjacent Interacting Masonry Structures) provides such experimental data by testing an aggregate of two buildings under two horizontal components of dynamic excitation. With the aim to advance the modelling of unreinforced masonry aggregates, a blind prediction competition is organized before the experimental campaign. Each group has been provided a complete set of construction drawings, material properties, testing sequence and the list of measurements to be reported. The applied modelling approaches span from equivalent frame models to Finite Element models using shell elements and discrete element models with solid elements. This paper compares the first entries, regarding the modelling approaches, results in terms of base shear, roof displacements, interface openings, and the failure modes.},
  language  = {en}
}
@inproceedings{TewariNeshvadGoldbachetal.2015,
  author    = {Tewari, Udit and Neshvad, Surena and Goldbach, Daniel and Sachau, J{\"u}rgen},
  title     = {Verification and Implementation of Pseudo-Random-Binary-Sequences for Online Determination of Grid Impedance Spectrum},
  series = {International Conference on Renewable Energies and Power Quality (ICREPQ´15), La Conuna, Spain, 25th to 27th March, 2015},
  booktitle = {International Conference on Renewable Energies and Power Quality (ICREPQ´15), La Conuna, Spain, 25th to 27th March, 2015},
  pages     = {6 Seiten},
  year      = {2015},
  language  = {en}
}
@inproceedings{TakenagaHerreraWerneretal.2013,
  author    = {Takenaga, Shoko and Herrera, Cony F. and Werner, Frederik and Biselli, Manfred and Schnitzler, Thomas and Sch{\"o}ning, Michael Josef and {\"O}hlschl{\"a}ger, Peter and Wagner, Torsten},
  title     = {Detection of the metabolic activity of cells by differential measurements based on a single light-addressable potentiometric sensor chip},
  series = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  booktitle = {11. Dresdner Sensor-Symposium : 9.-11.12.2013},
  organization    = {Dresdner Sensor-Symposium <11, 2013>},
  isbn      = {978-3-9813484-5-3},
  pages     = {63 -- 67},
  year      = {2013},
  language  = {en}
}
@inproceedings{TaddeiReindlParketal.2011,
  author    = {Taddei, Francesca and Reindl, Lukas and Park, Jin and Butenweg, Christoph and Karadogan, Faruk},
  title     = {Numerical investigation of AAC wall panels based on the damage plasticity constitutive law},
  series = {Cement, Wapno, Beton ; 2011, 7, Special issue: 5th International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' to be held at Bydgoszcz to celebrate 60 years of AAC experience in Poland, Bydgoszcz, September 14-17, 2011},
  booktitle = {Cement, Wapno, Beton ; 2011, 7, Special issue: 5th International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' to be held at Bydgoszcz to celebrate 60 years of AAC experience in Poland, Bydgoszcz, September 14-17, 2011},
  publisher = {Stowarzyszenie Producent{\´o}w Cementu i Wapna},
  address   = {Krakow},
  organization    = {International Conference on Autoclaved Aerated Concrete 'Securing a sustainable future' <5, 2011, Bydgoszcz>},
  issn      = {1425-8129},
  pages     = {86 -- 91},
  year      = {2011},
  language  = {en}
}
@inproceedings{TaddeiLozanaMicheletal.2015,
  author    = {Taddei, Francesca and Lozana, Lara and Michel, Philipp and Butenweg, Christoph and Klinkel, Sven},
  title     = {Practical recommendations for the foundation design of onshore wind turbines including soil-structure interaction},
  series = {5th International Conference on Computational Methods in Structural , Hersonissos, Greece Dynamics and Earthquake Engineering, COMPDYN 2015, 25.05.2015-27.05.2015, Hersonissos, Greece.},
  booktitle = {5th International Conference on Computational Methods in Structural , Hersonissos, Greece Dynamics and Earthquake Engineering, COMPDYN 2015, 25.05.2015-27.05.2015, Hersonissos, Greece.},
  editor    = {Papadrakakis, Manolis and Papadrakakis, M. and Papadopoulos, V. and Plevris, V.},
  year      = {2015},
  language  = {en}
}
@inproceedings{StollenwerkRiekeDahmenetal.2016,
  author    = {Stollenwerk, Dominik and Rieke, C. and Dahmen, Markus and Pieper, Martin},
  title     = {Biogas Production Modelling : A Control System Engineering Approach},
  series = {IOP Conference Series: Earth and Environmental Science. Bd. 32},
  booktitle = {IOP Conference Series: Earth and Environmental Science. Bd. 32},
  issn      = {1755-1315},
  doi       = {10.1088/1755-1315/32/1/012008},
  pages     = {012008/1 -- 012008/4},
  year      = {2016},
  language  = {en}
}
@inproceedings{StollenwerkKuvarakulKuperjans2013,
  author    = {Stollenwerk, Dominik and Kuvarakul, T. and Kuperjans, Isabel},
  title     = {Renewable energy supply for power dominated, energy intense production processes - a systematic conversion approach for the anodizing process},
  series = {IOP conference series: Earth and environmental science (EES)},
  volume    = {Vol. 16},
  booktitle = {IOP conference series: Earth and environmental science (EES)},
  number    = {H. 1},
  issn      = {1755-1315},
  pages     = {012142/1 -- 012142/4},
  year      = {2013},
  language  = {en}
}
@inproceedings{SteuerDankertSharmaBlecketal.2017,
  author    = {Steuer-Dankert, Linda and Sharma, Mamta Rameshwarlal and Bleck, Wolfgang and Leicht-Scholten, Carmen},
  title     = {Innovation through Diversity - Development of a Diversity and Innovation management concept},
  series = {International Conference on Innovation and Management : IAM23017S : Date: July 4-7, 2017, Osaka, Japan},
  booktitle = {International Conference on Innovation and Management : IAM23017S : Date: July 4-7, 2017, Osaka, Japan},
  editor    = {Farn, C. K.},
  publisher = {Kuang Hui Chiu},
  address   = {Osaka},
  issn      = {2218-6387},
  pages     = {Panel C},
  year      = {2017},
  abstract  = {Acknowledging that a diverse workforce could be a potential source of innovation, the current research deals with the fine details of why diversity management is central to achieving innovation in heterogeneous research groups and how this could be effectively realized in an organization. The types of heterogeneities addressed mainly include gender, qualification, academic discipline and intercultural perspectives. The type of organization being dealt with in this work is a complex association of research institutes at a technical university in Germany (RWTH Aachen University), namely a 'Cluster of Excellence', whereby several institutes of the university work collaboratively in different sub-projects. The 'Cluster of Excellence' is a part of the 'Excellence Initiative' of the German federal and state governments German Research Foundation (DFG) and German Council of Science and Humanities, with the ultimate aim of promoting cutting-edge research. To support interdisciplinary collaboration and thus the performance of the cluster, the development of a diversity and innovation management concept is presently in the conceptual phase and will be described in the frame of this paper. The 3-S-Diversity Model, composed of the three elements: skills, structure and strategy, serves as a basis for the development of the concept. The proposed concept consists of six phases; the first two phases lay the ground work by developing an understanding of the status quo on the forms of diversity in the Cluster of Excellence, the type of organizational structure of the member institutes and the varieties of specialist work cultures of the same. The third and the fourth phases build up on this foundation by means of qualitative and quantitative studies. While the third phase deals with the sensitization of the management level to the close connection between diversity and innovation; the need to manage them thereafter and find tailor-made methods of doing so, the fourth phase shall mainly focus on the mindset of the employees in this regard. The fifth phase shall consolidate the learnings and the ideas developed in the course of the first four phases into an implementable strategy. The ultimate phase shall be the implementation of this concept in the Cluster. The first three phases have been accomplished successfully and the preliminary results are already available.},
  language  = {en}
}
@inproceedings{SteuerDankertLeichtScholten2019,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Diversity- and innovation management in complex engineering organizations},
  series = {7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia},
  booktitle = {7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia},
  editor    = {Tipurić, Darko and Hruška, Domagoj},
  publisher = {Governance Research and Development Centre (CIRU)},
  address   = {Zagreb},
  pages     = {136 -- 157},
  year      = {2019},
  abstract  = {Diversity is increasingly being addressed as an innovation-promoting factor. For this reason, companies and institutions tackle the integration of a diversity management approach that enables a heterogenic perspective on innovation development. However, system-theoretical frameworks state that the implementation of diversity measures that are not tailored to the needs of the organization often leads to a rejection or reactivity with regard to the management approach. In this context, especially organizations, which are characterized by a specific hierarchical structure, a dominant habitus or specialist culture, must face the challenge of realizing a sustainable change of the corporate culture that sets the basis for implementing diversity management approaches. The presented research project focuses on analyzing the situation in a huge scientific collaborative project - so called Cluster of Excellence (CoE) - with the aim to implement a diversity - and innovation management strategy. Considering the influencing determinants, the CoE is characterized by its embeddedness in the scientific system, a complex organizational structure, and a high fluctuation rate. The paper presents a systemic approach of reflecting these factors in order to develop a diversity- and innovation management strategy. In this frame, the results of a quantitative survey of CoE employees and derived mindset-types are presented. The results show a need for taking different mindset-types into account, to be able to develop a tailored management strategy. The aim of the project is to give recommendations for developing a sustainable management concept that promotes both diversity and innovation by drawing on the persisting mindsets of organization members while reflecting top down as well as bottom up factors of implementation processes as well as the psychology of change. This paper addresses all who are concerned with the management of human resources in innovation processes and are striving for a cultural change within the framework of complex organizations.},
  language  = {en}
}
@inproceedings{SteuerDankertLeichtScholten2016,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Social responsibility and innovation - Key competencies for engineers},
  series = {ICERI 2016: 9th International Conference of Education, Research and Innovation: Conference Proceedings : Seville (Spain), 14-16 November},
  booktitle = {ICERI 2016: 9th International Conference of Education, Research and Innovation: Conference Proceedings : Seville (Spain), 14-16 November},
  isbn      = {978-84-617-5895-1},
  issn      = {2340-1095},
  doi       = {10.21125/iceri.2016.0353},
  pages     = {5967 -- 5976},
  year      = {2016},
  abstract  = {Engineers are of particular importance for the societies of tomorrow. The big social challenges society has to cope with in future, can only be mastered, if engineers link the development and innovation process closely with the requirements of people. As a result, in the frame of the innovation process engineers have to design and develop products for diverse users. Therefore, the consideration of diversity in this process is a core competence engineers should have. Implementing the consideration of diverse requirements into product design is also linked to the development of sustainable products and thus leads to social responsible research and development, the core concept formulated by the EU. For this reason, future engineers should be educated to look at the technical perspectives of a problem embedded in the related questions within societies they are developing their artefacts for. As a result, the aim of teaching engineering should be to prepare engineers for these requirements and to draw attention to the diverse needs in a globalized world. To match the competence profiles of future engineers to the global challenges and the resulting social responsibility, RWTH Aachen University, one of the leading technical universities in Germany, has established the bridging professorship "Gender and Diversity in Engineering" (GDI) which educates engineers with an interdisciplinary approach to expand engineering limits. The interdisciplinary teaching concept of the research group pursues an approach which imparts an application oriented Gender and Diversity expertise to future engineers. In the frame of an established teaching concept, which is a result of experiences and expertise of the research group, students gain theoretical knowledge about Gender and Diversity and learn how to transfer their knowledge into their later field of action. In the frame of the conference the institutional approach will be presented as well as the teaching concept which will be introduced by concrete course examples.},
  language  = {en}
}
@inproceedings{SteuerDankertLeichtScholten2017,
  author    = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {Innovation and Diversity : Integrating new perspectives into research associations},
  series = {12th European Conference on Innovation and Entrepreneurship (ECIE 2017) : Paris, France, 21-22 September 2017},
  booktitle = {12th European Conference on Innovation and Entrepreneurship (ECIE 2017) : Paris, France, 21-22 September 2017},
  isbn      = {978-1-911218-54-8},
  pages     = {767 -- 776},
  year      = {2017},
  abstract  = {The link between diversity and innovation is broadly discussed in the context of research and innovation processes. Many institutions and enterprises, specifically in commerce, have already tried to establish sustainable diversity management concepts, in order to increase the diversity of their workforce in addition to establishing a corporate culture of openness. Alongside the creation of a working place where different experiences and skills are valued equally, the entrepreneurial intention is to transfer diversity into economically relevant advantages. Taking into account the potential of diversity in research and innovation processes, the project "Diversity- and Innovation Management" was incorporated within a large interdisciplinary research Cluster. The project's purpose was to study the context between diversity and innovation in research associations and to later develop a customised management concept into an interdisciplinary research Cluster on integrative production technology with full integration. The challenge of such research associations lays in an organisational structure which is often described as being decentralised. Researchers coming from different academic disciplines, while having diverse habits, conduct research on large scientific issues and challenges. In addition, these researchers are socialised in different institutions and university chairs. Theses differences in leadership styles, business cultures and organisational strategies, follow into their research team work. Taking a closer look into the management of human resources suggests that decentral organised recruitment processes, as well as allocation of human resources, lead to a lacking overview in regard to missing competencies, perspectives and backgrounds in research networks. These circumstances are comparable to big corporate groups. While developing a management concept for research associations, these characteristics must be considered. To ensure this, the project follows a human-centred approach, which considers top-down, as well as bottom-up perspectives. This paper presents the applied mixed-method approach in the scientific issue described above. In the frame of the Cluster of Excellence "Integrative Production Technology for High-Wage Countries" research results based on quantitative, as well as qualitative studies, were presented as an application example. This paper provides a new perspective on the innovation and diversity context. Against the background of complex research organisations, the development approach of a management concept is particularly interesting.},
  language  = {en}
}
@inproceedings{SteuerDankertBergLeichtScholten2015,
  author    = {Steuer-Dankert, Linda and Berg, Tobias and Leicht-Scholten, Carmen},
  title     = {Breaking the habit - new approaches in engineering education},
  series = {Proceedings of the 43rd Annual Conference of the European Society for Engineering Education},
  booktitle = {Proceedings of the 43rd Annual Conference of the European Society for Engineering Education},
  isbn      = {978-2-87352-012-0},
  pages     = {11},
  year      = {2015},
  abstract  = {Within the framework of the project a genderand diversity-oriented teaching evaluation and modern, media-supported blended learning approaches were used in order to achieve the intended goals. First research results of the literature and status quo analysis were already implemented and tested in newly designed teaching approaches, for example in a multidisciplinary introductory lecture of civil engineering at RWTH Aachen University.},
  language  = {en}
}
@inproceedings{SteuerDankert2023,
  author    = {Steuer-Dankert, Linda},
  title     = {Training future skills - sustainability, interculturality \& innovation in a digital design thinking format},
  series = {Proceedings of the 19th International CDIO Conference},
  booktitle = {Proceedings of the 19th International CDIO Conference},
  pages     = {12 Seiten},
  year      = {2023},
  abstract  = {The complex questions of today for a world of tomorrow are characterized by their global impact. Solutions must therefore not only be sustainable in the sense of the three pillars of sustainability (economic, environmental, and social) but must also function globally. This goes hand in hand with the need for intercultural acceptance of developed services and products. To achieve this, engineers, as the problem solvers of the future, must be able to work in intercultural teams on appropriate solutions, and be sensitive to intercultural perspectives. To equip the engineers of the future with the so-called future skills, teaching concepts are needed in which students can acquire these methods and competencies in application-oriented formats. The presented course "Applying Design Thinking - Sustainability, Innovation and Interculturality" was developed to teach future skills from the competency areas Digital Key Competencies, Classical Competencies and Transformative Competencies. The CDIO Standard 3.0, in particular the standards 5, 6, 7 and 8, was used as a guideline. The course aims to prepare engineering students from different disciplines and cultures for their future work in an international environment by combining a digital teaching format with an interdisciplinary, transdisciplinary and intercultural setting for solving sustainability challenges. The innovative moment lies in the digital application of design thinking and the inclusion of intercultural as well as trans- and interdisciplinary perspectives in innovation development processes. In this paper, the concept of the course will be presented in detail and the particularities of a digital implementation of design thinking will be addressed. Subsequently, the potentials and challenges will be reflected and practical advice for integrating design thinking in engineering education will be given.},
  language  = {en}
}
@inproceedings{SirazitdinovaDulzonMueller2015,
  author    = {Sirazitdinova, Y. and Dulzon, A. and M{\"u}ller, Burghard},
  title     = {Project management practices in engineering university},
  series = {21st International Conference for Students and Young Scientists: Modern Technique and Technologies, MTT 2015; National Research Tomsk Polytechnic UniversityTomsk; Russian Federation; 5 October 2015 through 9 October 2015},
  booktitle = {21st International Conference for Students and Young Scientists: Modern Technique and Technologies, MTT 2015; National Research Tomsk Polytechnic UniversityTomsk; Russian Federation; 5 October 2015 through 9 October 2015},
  doi       = {10.1088/1757-899X/93/1/012080},
  pages     = {4 S.},
  year      = {2015},
  language  = {en}
}
@inproceedings{SildatkeKarwanniKraftetal.2020,
  author    = {Sildatke, Michael and Karwanni, Hendrik and Kraft, Bodo and Schmidts, Oliver and Z{\"u}ndorf, Albert},
  title     = {Automated Software Quality Monitoring in Research Collaboration Projects},
  series = {ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops},
  booktitle = {ICSEW'20: Proceedings of the IEEE/ACM 42nd International Conference on Software Engineering Workshops},
  doi       = {10.1145/3387940.3391478},
  pages     = {603 -- 610},
  year      = {2020},
  language  = {en}
}
@inproceedings{SchwagerAngeleSchwarzboezletal.2023,
  author    = {Schwager, Christian and Angele, Florian and Schwarzb{\"o}zl, Peter and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Model predictive assistance for operational decision making in molten salt receiver systems},
  series = {SolarPACES: Solar Power \& Chemical Energy Systems},
  booktitle = {SolarPACES: Solar Power \& Chemical Energy Systems},
  number    = {2815 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4623-6},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0151514},
  pages     = {8 Seiten},
  year      = {2023},
  abstract  = {Despite the challenges of pioneering molten salt towers (MST), it remains the leading technology in central receiver power plants today, thanks to cost effective storage integration and high cost reduction potential. The limited controllability in volatile solar conditions can cause significant losses, which are difficult to estimate without comprehensive modeling [1]. This paper presents a Methodology to generate predictions of the dynamic behavior of the receiver system as part of an operating assistance system (OAS). Based on this, it delivers proposals if and when to drain and refill the receiver during a cloudy period in order maximize the net yield and quantifies the amount of net electricity gained by this. After prior analysis with a detailed dynamic two-phase model of the entire receiver system, two different reduced modeling approaches where developed and implemented in the OAS. A tailored decision algorithm utilizes both models to deliver the desired predictions efficiently and with appropriate accuracy.},
  language  = {en}
}
@inproceedings{SchwagerAngeleNourietal.2022,
  author    = {Schwager, Christian and Angele, Florian and Nouri, Bijan and Schwarzb{\"o}zl, Peter and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Impact of DNI forecast quality on performance prediction for a commercial scale solar tower: Application of nowcasting DNI maps to dynamic solar tower simulation},
  series = {SolarPACES conference proceedings},
  booktitle = {SolarPACES conference proceedings},
  number    = {Vol. 1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.675},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concerning current efforts to improve operational efficiency and to lower overall costs of concentrating solar power (CSP) plants with prediction-based algorithms, this study investigates the quality and uncertainty of nowcasting data regarding the implications for process predictions. DNI (direct normal irradiation) maps from an all-sky imager-based nowcasting system are applied to a dynamic prediction model coupled with ray tracing. The results underline the need for high-resolution DNI maps in order to predict net yield and receiver outlet temperature realistically. Furthermore, based on a statistical uncertainty analysis, a correlation is developed, which allows for predicting the uncertainty of the net power prediction based on the corresponding DNI forecast uncertainty. However, the study reveals significant prediction errors and the demand for further improvement in the accuracy at which local shadings are forecasted.},
  language  = {en}
}
@inproceedings{SchulteSchwagerNoureldinetal.2023,
  author    = {Schulte, Jonas and Schwager, Christian and Noureldin, Kareem and May, Martin and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Gradient controlled startup procedure of a molten-salt power-to-heat energy storage plant based on dynamic process simulation},
  series = {SolarPACES: Solar Power \& Chemical Energy Systems},
  booktitle = {SolarPACES: Solar Power \& Chemical Energy Systems},
  number    = {2815 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4623-6},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0148741},
  pages     = {9 Seiten},
  year      = {2023},
  abstract  = {The integration of high temperature thermal energy storages into existing conventional power plants can help to reduce the CO2 emissions of those plants and lead to lower capital expenditures for building energy storage systems, due to the use of synergy effects [1]. One possibility to implement that, is a molten salt storage system with a powerful power-to-heat unit. This paper presents two possible control concepts for the startup of the charging system of such a facility. The procedures are implemented in a detailed dynamic process model. The performance and safety regarding the film temperatures at heat transmitting surfaces are investigated in the process simulations. To improve the accuracy in predicting the film temperatures, CFD simulations of the electrical heater are carried out and the results are merged with the dynamic model. The results show that both investigated control concepts are safe regarding the temperature limits. The gradient controlled startup performed better than the temperature-controlled startup. Nevertheless, there are several uncertainties that need to be investigated further.},
  language  = {en}
}
@inproceedings{SchulteSchwagerFrantzetal.2022,
  author    = {Schulte, Jonas and Schwager, Christian and Frantz, Cathy and Schloms, Felix and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Control concept for a molten salt receiver in star design: Development, optimization and testing with cloud passage scenarios},
  series = {SolarPACES conference proceedings},
  booktitle = {SolarPACES conference proceedings},
  number    = {Vol. 1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.693},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {A promising approach to reduce the system costs of molten salt solar receivers is to enable the irradiation of the absorber tubes on both sides. The star design is an innovative receiver design, pursuing this approach. The unconventional design leads to new challenges in controlling the system. This paper presents a control concept for a molten salt receiver system in star design. The control parameters are optimized in a defined test cycle by minimizing a cost function. The control concept is tested in realistic cloud passage scenarios based on real weather data. During these tests, the control system showed no sign of unstable behavior, but to perform sufficiently in every scenario further research and development like integrating Model Predictive Controls (MPCs) need to be done. The presented concept is a starting point to do so.},
  language  = {en}
}
@inproceedings{SchmittRosinButenweg2018,
  author    = {Schmitt, Timo and Rosin, Julia and Butenweg, Christoph},
  title     = {Seismic Impact And Design Of Buried Pipelines},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 12},
  year      = {2018},
  abstract  = {Seismic design of buried pipeline systems for energy and water supply is not only important for plant and operational safety but also for the maintenance of the supply infrastructure after an earthquake. The present paper shows special issues of the seismic wave impacts on buried pipelines, describes calculation methods, proposes approaches and gives calculation examples. This paper regards the effects of transient displacement differences and resulting tensions within the pipeline due to the wave propagation of the earthquake. However, the presented model can also be used to calculate fault rupture induced displacements. Based on a three-dimensional Finite Element Model parameter studies are performed to show the influence of several parameters such as incoming wave angle, wave velocity, backfill height and synthetic displacement time histories. The interaction between the pipeline and the surrounding soil is modeled with non-linear soil springs and the propagating wave is simulated affecting the pipeline punctually, independently in time and space. Special attention is given to long-distance heat pipeline systems. Here, in regular distances expansion bends are arranged to ensure movements of the pipeline due to high temperature. Such expansion bends are usually designed with small bending radii, which during the earthquake lead to high bending stresses in the cross-section of the pipeline. Finally, an interpretation of the results and recommendations are given for the most critical parameters.},
  language  = {en}
}
@inproceedings{SattlerCaminosUerlingsetal.2020,
  author    = {Sattler, Johannes, Christoph and Caminos, Ricardo Alexander Chico and {\"U}rlings, Nicolas and Dutta, Siddharth and Ruiz, Victor and Kalogirou, Soteris and Ktistis, Panayiotis and Agathokleous, Rafaela and Jung, Christian and Alexopoulos, Spiros and Atti, Vikrama Nagababu and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Operational experience and behaviour of a parabolic trough collector system with concrete thermal energy storage for process steam generation in Cyprus},
  series = {AIP Conference Proceedings},
  booktitle = {AIP Conference Proceedings},
  number    = {2303},
  doi       = {10.1063/5.0029278},
  pages     = {140004-1 -- 140004-10},
  year      = {2020},
  language  = {en}
}
@inproceedings{SattlerAlexopoulosCaminosetal.2019,
  author    = {Sattler, Johannes, Christoph and Alexopoulos, Spiros and Caminos, Ricardo Alexander Chico and Mitchell, John C. and Ruiz, Victor C. and Kalogirou, Soteris and Ktistis, Panayiotis K. and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Dynamic simulation model of a parabolic trough collector system with concrete thermal energy storage for process steam generation},
  series = {AIP Conference Proceedings},
  volume    = {2126},
  booktitle = {AIP Conference Proceedings},
  issn      = {0094243X},
  doi       = {10.1063/1.5117663},
  pages     = {150007-1 -- 150007-8},
  year      = {2019},
  language  = {en}
}
@inproceedings{SattlerSchneiderAngeleetal.2022,
  author    = {Sattler, Johannes Christoph and Schneider, Iesse Peer and Angele, Florian and Atti, Vikrama and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Development of heliostat field calibration methods: Theory and experimental test results},
  series = {SolarPACES conference proceedings},
  booktitle = {SolarPACES conference proceedings},
  number    = {Vol. 1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.678},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {In this work, three patent pending calibration methods for heliostat fields of central receiver systems (CRS) developed by the Solar-Institut J{\"u}lich (SIJ) of the FH Aachen University of Applied Sciences are presented. The calibration methods can either operate in a combined mode or in stand-alone mode. The first calibration method, method A, foresees that a camera matrix is placed into the receiver plane where it is subjected to concentrated solar irradiance during a measurement process. The second calibration method, method B, uses an unmanned aerial vehicle (UAV) such as a quadrocopter to automatically fly into the reflected solar irradiance cross-section of one or more heliostats (two variants of method B were tested). The third calibration method, method C, foresees a stereo central camera or multiple stereo cameras installed e.g. on the solar tower whereby the orientations of the heliostats are calculated from the location detection of spherical red markers attached to the heliostats. The most accurate method is method A which has a mean accuracy of 0.17 mrad. The mean accuracy of method B variant 1 is 1.36 mrad and of variant 2 is 1.73 mrad. Method C has a mean accuracy of 15.07 mrad. For method B there is great potential regarding improving the measurement accuracy. For method C the collected data was not sufficient for determining whether or not there is potential for improving the accuracy.},
  language  = {en}
}
@inproceedings{SattlerAttiAlexopoulosetal.2022,
  author    = {Sattler, Johannes Christoph and Atti, Vikrama and Alexopoulos, Spiros and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf and Dutta, Siddharth and Kioutsioukis, Ioannis},
  title     = {DNI forecast tool for the smart operation of a parabolic trough collector system with concrete thermal energy storage: Theory, results and outlook},
  series = {SolarPACES conference proceedings},
  booktitle = {SolarPACES conference proceedings},
  number    = {VOL. 1},
  publisher = {TIB Open Publishing},
  address   = {Hannover},
  issn      = {2751-9899 (online)},
  doi       = {10.52825/solarpaces.v1i.731},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {This work presents a basic forecast tool for predicting direct normal irradiance (DNI) in hourly resolution, which the Solar-Institut J{\"u}lich (SIJ) is developing within a research project. The DNI forecast data shall be used for a parabolic trough collector (PTC) system with a concrete thermal energy storage (C-TES) located at the company KEAN Soft Drinks Ltd in Limassol, Cyprus. On a daily basis, 24-hour DNI prediction data in hourly resolution shall be automatically produced using free or very low-cost weather forecast data as input. The purpose of the DNI forecast tool is to automatically transfer the DNI forecast data on a daily basis to a main control unit (MCU). The MCU automatically makes a smart decision on the operation mode of the PTC system such as steam production mode and/or C-TES charging mode. The DNI forecast tool was evaluated using historical data of measured DNI from an on-site weather station, which was compared to the DNI forecast data. The DNI forecast tool was tested using data from 56 days between January and March 2022, which included days with a strong variation in DNI due to cloud passages. For the evaluation of the DNI forecast reliability, three categories were created and the forecast data was sorted accordingly. The result was that the DNI forecast tool has a reliability of 71.4 \% based on the tested days. The result fulfils SIJ's aim to achieve a reliability of around 70 \%, but SIJ aims to still improve the DNI forecast quality.},
  language  = {en}
}
@inproceedings{RousseauKern2014,
  author    = {Rousseau, Alain and Kern, Alexander},
  title     = {How to deal with environmental risk in IEC 62305-2},
  series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  organization    = {International Conference on Lightning Protection <2014, Shanghai>},
  pages     = {521 -- 527},
  year      = {2014},
  abstract  = {The 2nd edition of the lightning risk management standard (IEC 62305-2) considers structures, which may endanger environment. In these cases, the loss is not limited to the structure itself, which is valid for usual structures. In the past (Edition 1) this danger was simply taken into account by a special hazard factor, multiplying the existing risk for the structure with a number. Now, in the edition 2, we add to the risk for the structure itself a "second risk" due to the losses outside the structure. The losses outside can be treated independently from what occurs inside. This is a major advantage to analyze the risk for sensitive structures, like chemical plants, nuclear plants, or structures containing explosives, etc. In this paper, the existing procedure given by the European version EN 62305-2 Ed.2 is further developed and applied to a few structures.},
  language  = {en}
}
@inproceedings{RosinKubalskiButenweg2014,
  author    = {Rosin, Julia and Kubalski, Thomas and Butenweg, Christoph},
  title     = {Seismic Design of cylindrical liquid storage tanks},
  series = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed.},
  booktitle = {Seismic design of industrial facilities : proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF-Conference) ; [Aachen, 26. - 27. September 2013] / Chair of Structural Statics and Dynamics, RWTH Aachen. Sven Klinkel ..., ed.},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  organization    = {International Conference on Seismic Design of Industrial Facilities <2013, Aachen>},
  isbn      = {978-3-658-02810-7 (E-Book) ; 978-3-658-02809-1 (Print)},
  doi       = {10.1007/978-3-658-02810-7_36},
  pages     = {429 -- 440},
  year      = {2014},
  language  = {en}
}
@inproceedings{RosinKubalskiButenweg2013,
  author    = {Rosin, Julia and Kubalski, Thomas and Butenweg, Christoph},
  title     = {Seismic isolation of cylindrical liquid storage tanks},
  series = {Seismic design of industrial facilities},
  booktitle = {Seismic design of industrial facilities},
  editor    = {Klinkel, Sven and Butenweg, Christoph and Lin, Gao and Holtschoppen, Britta},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  isbn      = {978-3-658-02810-7},
  doi       = {10.1007/978-3-658-02810-7_36},
  pages     = {429 -- 440},
  year      = {2013},
  abstract  = {Seismic excited liquid filled tanks are subjected to extreme loading due to hydrodynamic pressures, which can lead to nonlinear stability failure of the thinwalled cylindrical tanks, as it is known from past earthquakes. A significant reduction of the seismically induced loads can be obtained by the application of base isolation systems, which have to be designed carefully with respect to the modified hydrodynamic behaviour of the tank in interaction with the liquid. For this reason a highly sophisticated fluid-structure interaction model has to be applied for a realistic simulation of the overall dynamic system. In the following, such a model is presented and compared with the results of simplified mathematical models for rigidly supported tanks. Finally, it is examined to what extent a simple mechanical model can represent the behaviour of a base isolated tank in case of seismic excitation},
  language  = {en}
}
@inproceedings{RosinButenwegBoesenetal.2018,
  author    = {Rosin, Julia and Butenweg, Christoph and Boesen, Niklas and Gellert, Christoph},
  title     = {Evaluation of the Seismic Behavior of a Modern URM Building During the 2012 Northern Italy Earthquakes},
  series = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  booktitle = {16th European Conference on Earthquake Engineering, Thessaloniki, 18-21 June, 2018},
  pages     = {1 -- 12},
  year      = {2018},
  language  = {en}
}
@inproceedings{RosinButenweg2014,
  author    = {Rosin, Julia and Butenweg, Christoph},
  title     = {Seismic isolation of cylindrical liquid storage tanks},
  series = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)},
  booktitle = {Proceedings of the 9th European Conference on Structural Dynamics, EURODYN 2014 Porto, Portugal, 30 June - 2 July 2014 / A. Cunha, E. Caetano, .... (eds.)},
  address   = {Porto},
  organization    = {European Conference on Structural Dynamics, EURODYN <9, 2014, Porto>},
  isbn      = {978-972-752-165-4},
  pages     = {3145 -- 3152},
  year      = {2014},
  language  = {en}
}
@inproceedings{RosinMykoniouButenweg2017,
  author    = {Rosin, J. and Mykoniou, K. and Butenweg, Christoph},
  title     = {Analysis Of Base Isolated Liquid Storage Tanks With 3D Fsi-Analysis As Well As Simplified Approaches},
  series = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake Engineering, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  pages     = {1 -- 14},
  year      = {2017},
  abstract  = {Tanks are preferably designed, for cost-saving reasons, as circular, cylindrical, thin-walled shells. In case of seismic excitation, these constructions are highly vulnerable to stability failures. An earthquake-resistant design of rigidly supported tanks for high seismic loading demands, however, uneconomic wall thicknesses. A cost-effective alternative can be provided by base isolation systems. In this paper, a simplified seismic design procedure for base isolated tanks is introduced, by appropriately modifying the standard mechanical model for flexible, rigidly supported tanks. The non-linear behavior of conventional base isolation systems becomes an integral part of a proposed simplified process, which enables the assessment of the reduced hydrodynamic forces acting on the tank walls and the corresponding stress distribution. The impulsive and convective actions of the liquid are taken into account. The validity of this approach is evaluated by employing a non-linear fluid-structure interaction algorithm of finite element method. Special focus is placed on the boundary conditions imposed from the base isolation and the resulting hydrodynamic pressures. Both horizontal and vertical component of ground motion are considered in order to study the principal effects of the base isolation on the pressure distribution of the tank walls. The induced rocking effects associated with elastomeric bearings are discussed. The results manifest that base isolated tanks can be designed for seismic loads by means of the proposed procedure with sufficient accuracy, allowing to dispense with numerically expensive techniques.},
  language  = {en}
}
@inproceedings{RochefortVerverGrunendahletal.2005,
  author    = {Rochefort, E. de and Verver, M. and Grunendahl, A. and Mooi, H. and Butenweg, Christoph},
  title     = {Detailed modelling of the lumbar spine for investigation of low back pain},
  series = {Digital Human Modeling for Design and Engineering Symposium : Iowa City, Iowa June 14-16, 2005. (SAE technical papers series ; 2005-1-2716)},
  booktitle = {Digital Human Modeling for Design and Engineering Symposium : Iowa City, Iowa June 14-16, 2005. (SAE technical papers series ; 2005-1-2716)},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  organization    = {Society of Automotive Engineers},
  issn      = {0096-736X},
  doi       = {10.4271/2005-01-2716},
  pages     = {1 -- 11},
  year      = {2005},
  language  = {en}
}
@inproceedings{RigaPitilakisButenwegetal.2022,
  author    = {Riga, Evi and Pitilakis, Kyriazis and Butenweg, Christoph and Apostolaki, Stefania and Karatzetzou, Anna},
  title     = {Investigating the impact of the new European Seismic Hazard Model ESHM20 on the seismic design and safety control of industrial facilities},
  series = {The Third European Conference on Earthquake Engineering and Seismology September 4 - September 9, 2022, Bucharest},
  booktitle = {The Third European Conference on Earthquake Engineering and Seismology September 4 - September 9, 2022, Bucharest},
  editor    = {Arion, Cristian and Scupin, Alexandra and Ţigănescu, Alexandru},
  isbn      = {978-973-100-533-1},
  pages     = {3261 -- 3270},
  year      = {2022},
  abstract  = {The seismic performance and safety of major European industrial facilities has a global interest for Europe, its citizens and economy. A potential major disaster at an industrial site could affect several countries, probably far beyond the country where it is located. However, the seismic design and safety assessment of these facilities is practically based on national, often outdated seismic hazard assessment studies, due to many reasons, including the absence of a reliable, commonly developed seismic hazard model for whole Europe. This important gap is no more existing, as the 2020 European Seismic Hazard Model ESHM20 was released in December 2021. In this paper we investigate the expected impact of the adoption of ESHM20 on the seismic demand for industrial facilities, through the comparison of the ESHM20 probabilistic hazard at the sites where industrial facilities are located with the respective national and European regulations. The goal of this preliminary work in the framework of Working Group 13 of the European Association for Earthquake Engineering (EAEE), is to identify potential inadequacies in the design and safety control of existing industrial facilities and to highlight the expected impact of the adoption of the new European Seismic Hazard Model on the design of new industrial facilities and the safety assessment of existing ones.},
  language  = {en}
}
@inproceedings{RensFerreinPoel2008,
  author    = {Rens, Gavin and Ferrein, Alexander and Poel, Etienne van der},
  title     = {Extending DTGolog to deal with POMD-Ps},
  series = {Proceedings of the Nineteenth Annual Symposium of the Pattern Recognition Association of South Africa (PRASA 2008)},
  booktitle = {Proceedings of the Nineteenth Annual Symposium of the Pattern Recognition Association of South Africa (PRASA 2008)},
  organization    = {Pattern Recognition Association of South Africa},
  pages     = {49 -- 54},
  year      = {2008},
  language  = {en}
}
@inproceedings{RendonSchwagerGhiasietal.2020,
  author    = {Rendon, Carlos and Schwager, Christian and Ghiasi, Mona and Schmitz, Pascal and Bohang, Fakhri and Caminos, Ricardo Alexander Chico and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Modeling and upscaling of a pilot bayonettube reactor for indirect solar mixed methane reforming},
  series = {AIP Conference Proceedings},
  booktitle = {AIP Conference Proceedings},
  number    = {2303},
  doi       = {10.1063/5.0029974},
  pages     = {170012-1 -- 170012-9},
  year      = {2020},
  language  = {en}
}
@inproceedings{RenaultButenwegMistler2005,
  author    = {Renault, Philippe and Butenweg, Christoph and Mistler, Michael},
  title     = {Seismic vulnerability assessment system for bridges},
  series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>},
  isbn      = {1-905088-00-0},
  pages     = {1 -- 14},
  year      = {2005},
  language  = {en}
}
@inproceedings{ReindlParkNordaetal.2010,
  author    = {Reindl, Lukas and Park, Jin and Norda, Hannah and Butenweg, Christoph},
  title     = {Seismic design of masonry walls subject to out-of-plane bending},
  series = {Proceedings of the Tenth International Conference on Computational Structures Technology : Valencia, Spain, 14 - 17 September 2010 / organised in association with: Universidad Politecnica de Valencia ... Ed. by B. H. V. Topping ...},
  booktitle = {Proceedings of the Tenth International Conference on Computational Structures Technology : Valencia, Spain, 14 - 17 September 2010 / organised in association with: Universidad Politecnica de Valencia ... Ed. by B. H. V. Topping ...},
  publisher = {Civil-Comp Press},
  address   = {Kippen},
  organization    = {International Conference on Computational Structures Technology <10, 2010, Valencia>},
  isbn      = {978-1-905088-36-2},
  doi       = {10.4203/ccp.93.348},
  pages     = {Paper 348},
  year      = {2010},
  language  = {en}
}
@inproceedings{ReindlButenwegKubalski2011,
  author    = {Reindl, Lukas and Butenweg, Christoph and Kubalski, Thomas},
  title     = {Numerical simulation of unreinforced masonry walls subject to dynamic out-of-plane loading},
  series = {COMPDYN 2011 : ECCOMAS Thematic Conference ; Proceedings of the 3rd International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering ; 25-28 May, 2011, Corfu, Greece / Eds.: M. Papadrakakis ...},
  booktitle = {COMPDYN 2011 : ECCOMAS Thematic Conference ; Proceedings of the 3rd International Conference on Computational Methods in Structural Dynamics and Earthquake Engineering ; 25-28 May, 2011, Corfu, Greece / Eds.: M. Papadrakakis ...},
  publisher = {National Technical Univ. of Athens},
  address   = {Athen},
  organization    = {COMPDYN <2011, Corfu>},
  isbn      = {978-960-99994-0-3},
  pages     = {1 -- 10},
  year      = {2011},
  language  = {en}
}
@inproceedings{RajanKubalskiAltayetal.2017,
  author    = {Rajan, Sreelakshmy and Kubalski, Thomas and Altay, Okyay and Dalguer, Luis A and Butenweg, Christoph},
  title     = {Multi-dimensional fragility analysis of a RC building with components using response surface method},
  series = {24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017},
  booktitle = {24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017},
  publisher = {International Assn for Structural Mechanics in Reactor Technology (IASMiRT)},
  address   = {Raleigh, USA},
  isbn      = {9781510856776},
  pages     = {3126 -- 3135},
  year      = {2017},
  abstract  = {Conventional fragility curves describe the vulnerability of the main structure under external hazards. However, in complex structures such as nuclear power plants, the safety or the risk depends also on the components associated with a system. The classical fault tree analysis gives an overall view of the failure and contains several subsystems to the main event, however, the interactions in the subsystems are not well represented. In order to represent the interaction of the components, a method suggested by Cimellaro et al. (2006) using multidimensional performance limit state functions to obtain the system fragility curves is adopted. This approach gives the possibility of deriving the cumulative fragility taking into account the interaction of the response of different components. In this paper, this approach is used to evaluate seismic risk of a representative electrical building infrastructure, including the component, of a nuclear power plant. A simplified model of the structure, with nonlinear material behavior is employed for the analysis in Abaqus©. The input variables considered are the material parameters, boundary conditions and the seismic input. The variability of the seismic input is obtained from selected ground motion time histories of spectrum compatible synthetic ccelerograms. Unlike the usual Monte Carlo methods used for the probabilistic analysis of the structure, a computationally effective response surface method is used. This method reduces the computational effort of the calculations by reducing the required number of samples.},
  language  = {en}
}
@inproceedings{RajanHoltschoppenDalgueretal.2016,
  author    = {Rajan, Sreelakshmy and Holtschoppen, B. and Dalguer, L. A. and Klinkel, S. and Butenweg, Christoph},
  title     = {Seismic fragility analysis of a non-conventional reinforced concrete structure considering different uncertainties},
  series = {Proceedings of ISMA2016, International Conference on Noise and Vibration Engineering/USD2016, International Conference on Uncertainty in Structural Dynamics, / ISMA 2016, USD 2016},
  booktitle = {Proceedings of ISMA2016, International Conference on Noise and Vibration Engineering/USD2016, International Conference on Uncertainty in Structural Dynamics, / ISMA 2016, USD 2016},
  editor    = {Sas, P.},
  publisher = {KU Leuven},
  address   = {Leuven},
  pages     = {4213 -- 4225},
  year      = {2016},
  language  = {en}
}
@inproceedings{RajanButenwegDalgueretal.2017,
  author    = {Rajan, S. and Butenweg, Christoph and Dalguer, L. A. and An, J. H. and Renault, P. and Klinkel, S.},
  title     = {Fragility curves for a three-storey reinforced concrete test structure of the international benchmark SMART 2013},
  series = {16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  booktitle = {16th World Conference on Earthquake, 16WCEE 2017 Santiago Chile, January 9th to 13th 2017},
  publisher = {Chilean Association on Seismology and Earthquake Engineering (ACHISINA)},
  year      = {2017},
  language  = {en}
}
@inproceedings{PuetzBaierBrauneretal.2022,
  author    = {P{\"u}tz, Sebastian and Baier, Ralph and Brauner, Philipp and Brillowski, Florian and Dammers, Hannah and Liehner, Luca and Mertens, Alexander and Rodemann, Niklas and Schneider, Sebastian and Schollemann, Alexander and Steuer-Dankert, Linda and Vervier, Luisa and Gries, Thomas and Leicht-Scholten, Carmen and Nagel, Saskia K. and Piller, Frank T. and Schuh, G{\"u}nther and Ziefle, Martina and Nitsch, Verena},
  title     = {An interdisciplinary view on humane interfaces for digital shadows in the internet of production},
  series = {2022 15th International Conference on Human System Interaction (HSI)},
  booktitle = {2022 15th International Conference on Human System Interaction (HSI)},
  publisher = {IEEE},
  isbn      = {978-1-6654-6823-7 (Print)},
  issn      = {2158-2246 (Print)},
  doi       = {10.1109/HSI55341.2022.9869467},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {Digital shadows play a central role for the next generation industrial internet, also known as Internet of Production (IoP). However, prior research has not considered systematically how human actors interact with digital shadows, shaping their potential for success. To address this research gap, we assembled an interdisciplinary team of authors from diverse areas of human-centered research to propose and discuss design and research recommendations for the implementation of industrial user interfaces for digital shadows, as they are currently conceptualized for the IoP. Based on the four use cases of decision support systems, knowledge sharing in global production networks, human-robot collaboration, and monitoring employee workload, we derive recommendations for interface design and enhancing workers' capabilities. This analysis is extended by introducing requirements from the higher-level perspectives of governance and organization.},
  language  = {en}
}
@inproceedings{PieperSchulz2014,
  author    = {Pieper, Martin and Schulz, Silvia},
  title     = {Teaching Simulation Methods with COMSOL Multiphysics},
  organization    = {COMSOL Conference <2014, Cambridge>},
  pages     = {7},
  year      = {2014},
  abstract  = {This paper describes two courses on simulation methods for graduate students: "Simulation Methods" and "Simulation and Optimization in Virtual Engineering" The courses were planned to teach young engineers how to work with simulation software as well as to understand the necessary mathematical background. As simulation software COMSOL is used. The main philosophy was to combine theory and praxis in a way that motivates the students. In addition "soft skills" should be improved. This was achieved by project work as final examination. As underlying didactical principle the ideas of Bloom's revised taxonomy were followed. The paper basically focusses on educational aspects, e.g. how to structure the course, plan the exercises, organize the project work and include practical COMSOL examples.},
  language  = {en}
}
@inproceedings{PhilippBrillowskiDammersetal.2020,
  author    = {Philipp, Brauner and Brillowski, Florian Sascha and Dammers, Hannah and K{\"o}nigs, Peter and Kordtomeikel, Frauke Carole and Petruck, Henning and Schaar, Anne Kathrin and Schmitz, Seth and Steuer-Dankert, Linda and Mertens, Alexander and Gries, Thomas and Leicht-Scholten, Carmen and Nagel, Saskia K. and Nitsch, Verena and Schuh, G{\"u}nther and Ziefle, Martina},
  title     = {A research framework for human aspects in the internet of production: an intra-company perspective},
  series = {Advances in Manufacturing, Production Management and Process Control: Proceedings of the AHFE 2020 Virtual Conferences on Human Aspects of Advanced Manufacturing, Advanced Production Management and Process Control, and Additive Manufacturing, Modeling Systems and 3D Prototyping, July 16-20, 2020, USA},
  booktitle = {Advances in Manufacturing, Production Management and Process Control: Proceedings of the AHFE 2020 Virtual Conferences on Human Aspects of Advanced Manufacturing, Advanced Production Management and Process Control, and Additive Manufacturing, Modeling Systems and 3D Prototyping, July 16-20, 2020, USA},
  editor    = {Mrugalska, Beata and Trzcielinski, Stefan and Karwowski, Waldemar and Nicolantonio, Massimo Di and Roossi, Emilio},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-51980-3},
  doi       = {10.1007/978-3-030-51981-0_1},
  pages     = {3 -- 17},
  year      = {2020},
  abstract  = {Digitalization in the production sector aims at transferring concepts and methods from the Internet of Things (IoT) to the industry and is, as a result, currently reshaping the production area. Besides technological progress, changes in work processes and organization are relevant for a successful implementation of the "Internet of Production" (IoP). Focusing on the labor organization and organizational procedures emphasizes to consider intra-company factors such as (user) acceptance, ethical issues, and ergonomics in the context of IoP approaches. In the scope of this paper, a research approach is presented that considers these aspects from an intra-company perspective by conducting studies on the shop floor, control level and management level of companies in the production area. Focused on four central dimensions—governance, organization, capabilities, and interfaces—this contribution presents a research framework that is focused on a systematic integration and consideration of human aspects in the realization of the IoP.},
  language  = {en}
}
@inproceedings{PfundtVogelsangGerling1988,
  author    = {Pfundt, H. and Vogelsang, D. and Gerling, Ulrich},
  title     = {Calculation of the crust profile in aluminium reduction cells by thermal computer modelling},
  series = {Light metals 1989 : 118th annual meeting of the Minerals, Metals and Materials Society, Las Vegas, NV, Feb. 27 - Mar. 03. 1989},
  booktitle = {Light metals 1989 : 118th annual meeting of the Minerals, Metals and Materials Society, Las Vegas, NV, Feb. 27 - Mar. 03. 1989},
  publisher = {Minerals, Metals and Materials Soc.},
  address   = {Warrendale, Pa.},
  pages     = {371 -- 377},
  year      = {1988},
  language  = {en}
}